Aerial Units Contract end Date

Transcription

1 Aerial Units Contract end Date Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip Bloomington, MN Phone #: Toll Free #: Fax #: Address: Website: Version of Excel used: Aerial Units Make Elliot Warranty 1 year parts and labor Date & I.D. of Price List 12/1/2017 Elliot Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed CVI Inspection Please see pricing below Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED 9150 Pillsbury Avenue South, Delivery Starting Point Address Bloomington, MN Price per loaded mile for delivery $ 4.50 Delivery Time Frame in calendar days ARO Determined at time of order Shop Rates Shop Rate for Mechanical work $ Body Shop Rate $ *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic 12/1/2017 Elliot 6.01 M43R Elliott M43R Rear Mount Aerial Device Installed Elliott HiReach M43R having a 48' working height. Basic unit includes $105, base assembly supporting rear mounted rotating turret, hydraulically

2 powered continuous rotation mechanism, oil reservoir mounted to turret box, oil, and manual hydraulic controls mounted to turret. Electronic proportional three stick remote controls on platform. Underslung "A" outriggers at rear and overframe vertical outriggers at front. Steel two section hydraulically telescoping boom with double acting lift cylinder. Internal cable carrier to boom tip. Hydraulically self-leveling and rotating 30" x 54" EZR work platform with remote leveling from platform. Power take off or clutch pump drive, pressure gauge, pump and holding valves on all cylinders. Remote start/stop at upper and lower controls, 12-volt emergency pump with switch at upper and lower controls, PTO hour meter, backup alarm, fire extinguisher, and two body harness and lanyard. Safety triangle kit. Installed on chassis, tested, checked and ready to operate. Unit certified to ANSI A92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices. Platform capacity 500 lbs. 13' Wood Bed With LED Lights (For Use With Crossbody Box) Standard ICC Rear Bumper With Steps and Grab Handles Tie Down Rails On Both Sides of Bed 2,000 lb. Planetary Winch With Anti-Two- Block Switch, Horn, Cable & Retainer Lug 500 lb. Platform Mounted Hydraulic Jib Winch 110 Volt Line to Platform Walkway Access to Platform When Boom Stowed (19,500 GVWR Chassis) Hot Shift PTO For Automatic Transmission 98" x 18" x 18" Steel Crossbody Box 48" x 20" x 18" Steel Underbody Mounted Steel Cable Carrier Cover (2) LED Strobe Lights, (1) Mounted on Each Side of Turret Near Top With Switch in Cab Chassis Rating - 19,500 lb. GVWR Non CDL HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD)

3 Factory supplied chassis 6.02 Dodge Dodge X2 $47, HP Cummins 6.7 L I6 Turbo Diesel Engine, 50 state emissions, 192" WB, 108" CA 6-speed automatic transmission Aisin AS69RC HD, 19,500 GVWR, 7,250 lb front axle, 13,500 lb rear axle P225/70R19.5F front & rear tires, 4.44 axle ratio, anti spin rear axle, PTO prep, 52 gallon rear fuel tank, Platform running boards, Bright bumper/grille, eng block heater, cruise, air conditioning, AM/FM w/ CD with Bluetooth, 40/20/40 vinyl split bench seat, power windows & locks, heated mirrors. Color: White Chassis Charge 6.03 CHASSIS- CHRG Handling charge for customer supplied chassis $2, I50F Elliott I50F Behind Cab Mount Aerial Device One new Elliott HiReach I50F having a 55' working height. Basic unit $129, includes base assembly supporting front mounted rotating turret, hydraulically powered continuous rotation mechanism, oil reservoir mounted to truck frame, oil, and manual hydraulic controls mounted to turret and fiber-optic proportional three stick controls in platform. Base mounted "A" type hydraulically powered, individually controlled main outriggers. Underslung "A" type secondary outriggers for rear stabilization. Two high strength steel boom sections and one fiberglass boom section hydraulically telescoping with one double acting 6 lift cylinder for boom lift. Covered cable carrier to boom tip. Hydraulic self-leveling 40" x 60" top mount fiberglass work platform with hydraulic rotation and remote leveling control from

4 6.05 Freightliner platform. Power take-off and holding valves on all cylinders. Remote start/shutdown at upper and lower controls. Safety triangle kit, (2) body harnesses and fire extinguisher. LED Lights to Include all bed marker lights, stop, tail and turn. Installed on chassis, tested and ready to operate. Unit certified to ANSI A92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices, Category C insulation 46KV rated. Platform capacity 600 lbs. 18' Wood Bed With LED Lights Standard ICC Rear Bumper Tie Down Rails On Both Sides of Bed 3,650 lb. Winch With 180' of 3/4" Double Braided Polyester Rope, Retainer Lug and Wireless Anti Two Block Warning System 500 lb. Platform Mounted Hydraulic Jib Winch With Synthetic Rope Hot Shift PTO For Automatic Transmission 48" x 20" x 18" Steel Underbody Mounted (2) LED Strobe Lights, (1) Mounted on Each Side of Turret Near Top With Switch in Cab Chassis Rating - Sum of Axle Capacities HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD) Factory supplied chassis M Freightliner M2 106 $73, hp Cummins B6.7 diesel engine (660 lb/ft torque), 210" WB, 144" C.A., 90" AF Allison 3500 RDS automatic transmission, 33,000 GVWR, 13,000 lb front axle, 20,000 lb rear axle 11R22.5 front and rear tires, air brakes, 50 gallon alum fuel tank (LH), AM/FM radio, cruise control, air conditioning, air ride driver seat, two-man pass. bench seat. Color: White. 1-year tow warranty. Chassis Charge 6.06 CHASSIS- CHRG Handling charge for customer supplied chassis $2,953.00

5 6.07 I60F Elliott I60F Behind Cab Mount Aerial Device One new Elliott HiReach I60F having 65' working height. Basic unit $145, includes base assembly supporting front mounted rotating turret, hydraulically powered continuous rotation mechanism, oil reservoir mounted to truck frame, oil, and manual hydraulic controls mounted to turret. Fiber-optic proportional three-stick controls in platform. Base mounted MH type hydraulically powered individually controlled main outriggers. Underslung "A" type outriggers for rear stabilization. Front bumper stabilizer. Two high strength steel boom sections and one fiberglass boom section hydraulically telescoping boom with one double acting lift cylinder. Covered cable carrier to boom tip. Hydraulic self-leveling 40" x 60" top mount fiberglass work platform with hydraulic rotation and remote leveling control from platform. Power take-off and holding valves on all cylinders. Remote start/shutdown at upper and lower controls. Safety triangle kit, (2) body harnesses and fire extinguisher. LED Lights to Include all bed marker lights, stop, tail and turn. Installed on chassis, tested and ready to operate. Unit certified to ANSI A92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices, Category C insulation 46KV 22' Wood Bed With LED Lights Standard ICC Rear Bumper Tie Down Rails On Both Sides of Bed 3,650 lb. Winch With 180' of 3/4" Double Braided Polyester Rope, Retainer Lug and Wireless Anti Two Block Warning System 500 lb. Platform Mounted Hydraulic Jib Winch With Synthetic Rope Hot Shift PTO For Automatic Transmission 48" x 20" x 18" Steel Underbody Mounted (2) LED Strobe Lights, (1) Mounted on Each Side of Turret

6 6.08 Freightliner Near Top With Switch in Cab HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD) Factory supplied chassis M Freightliner M2-106 $74, hp Cummins B6.7 diesel engine (660 lb/ft torque), 222" WB, 156" C.A., 90" AF Allison 3500 RDS automatic transmission, 33,000 GVWR, 13,000 lb front axle, 20,000 lb rear axle 11R22.5 front and rear tires, air brakes, 50 gallon alum fuel tank (LH), AM/FM radio, cruise control, air conditioning, air ride driver seat, two-man pass. bench seat. Color: White. 1-year tow warranty. Chassis Charge 6.09 CHASSIS- CHRG Handling charge for customer supplied chassis $2, V60F Elliott V60F Behind Cab Mount Aerial Device Elliott HiReach V60F having a 63' working height. Basic unit includes $95, base assembly supporting a front mounted rotating turret, hydraulically powered continuous rotation mechanism, oil reservoir mounted to truck frame with oil. Selector switches mounted at turret. Electronic proportional controls on platform. "A" style hydraulically powered, individually controlled front main outriggers and A style secondary outriggers. Steel three section hydraulically telescoping boom. Hydraulically self-leveling and rotating top mount 30" x 40" work platform with integral tool tray. Leveling from platform. Lifting eye in boom tip rated at 500 lbs. PTO or pump clutch drive, pressure gauge, pump, and holding valve on all cylinders. Remote start/shutdown at upper and lower controls. 12-volt emergency pump with switch at

7 upper and lower controls, backup alarm, fire extinguisher, and two body harnesses and lanyards. Safety triangle kit. Installed on chassis, tested, checked and ready to operate. Unit certified to ANSI A92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices. Platform capacity 500 lbs. 15' 6" Low Profile Wood Bed With LED Lights Standard ICC Rear Bumper 500 lb. Platform Jib With Electric Winch Mounted Under Platform 110 Volt Line to Platform Hot Shift PTO For Automatic Transmission 48" x 20" x 18" Steel Underbody Mounted Chassis Rating - Sum of Axle Capacities (2) LED Strobe Lights, (1) Mounted on Each Side of Turret Near Top With Switch in Cab HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD) Factory Supplied Chassis 6.11 Dodge Dodge x2 $47, HP Cummins 6.7 L I6 Turbo Diesel Engine, 50 state emissions, 192" WB, 108" CA 6-speed automatic transmission Aisin AS69RC HD, 19,500 GVWR, 7,250 lb front axle, 13,500 lb rear axle P225/70R19.5F front & rear tires, 4.44 axle ratio, anti spin rear axle, PTO prep, 52 gallon rear fuel tank, Platform running boards, Bright bumper/grille, eng block heater, cruise, air conditioning, AM/FM w/ CD with Bluetooth, 40/20/40 vinyl split bench seat, power windows & locks, heated mirrors. Color: White Chassis Charge 6.12 CHASSIS- CHRG Handling charge for customer supplied chassis $2, S50R S50R Skywalk Aerial Device Elliott Skywalk S50R, having a 55' working height. Basic unit includes $142,379.00

8 base assembly supporting rear mounted rotating turret, hydraulically powered continuous rotation mechanism, oil reservoir mounted to truck frame, oil, and manual hydraulic controls mounted to turret. Electronic proportional four stick remote controls in platform. Base mounted "MH" type hydraulically powered, individually controlled rear main outriggers and A secondary outriggers behind cab. High strength steel three-section hydraulically telescoping boom with one double acting 6 lift cylinder. Exposed cable carrier to boom tip. Hydraulically self-leveling end mounted 2'10" wide x 12' long work platform with 180 degree hydraulic rotation and remote leveling from platform. Power take off and pump drive, pressure gauge, pump and holding valves on all cylinders. Remote start/ shutdown at upper and lower controls, 12-volt emergency pump with switch at upper and lower controls, PTO hour meter, backup alarm, fire extinguisher, and (2) body harnesses and lanyards. Unit certified to ANSI 92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices. Installed on chassis, tested and ready to operate. Platform capacity 900 lbs. 14' Wood Bed With LED Lights (For Use With Crossbody Box) Standard ICC Rear Bumper With Steps and Grab Handles Tie Down Rails On Both Sides of Bed 9,000 lb. Planetary Winch With Anti-Two- Block Switch, Horn, Two Part Hook & 180' 7/16" Cable & Retainer Lug (Includes Radio Load Cell) 500 lb. Platform Mounted Jib With Hydraulic Winch. 300 lb Capacity at 6' Extension. 110 Volt Line to Platform Hot Shift PTO For Automatic Transmission 98" x 36" x 24" Steel Crossbody Box 48" x 20" x 18" Steel Underbody Mounted

9 6.14 Freightliner Steel Cable Carrier Cover Walkway Access to Platform When Boom Stowed (2) LED Strobe Lights, (1) Mounted on Each Side of Turret Near Top With Switch in Cab Chassis Rating - Sum of Axle Capacities HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD) Factory Supplied Chassis M Freightliner M2-106 $73, hp Cummins B6.7diesel engine (660 lb/ft torque), 210" WB, 144" C.A., 90" AF Allison 3500 RDS automatic transmission, 33,000 GVWR, 13,000 lb front axle, 20,000 lb rear axle 11R22.5 front and rear tires, air brakes, 50 gallon alum fuel tank (LH), AM/FM radio, cruise control, air conditioning, air ride driver seat, two-man pass. bench seat. Color: White. 1-year tow warranty. Chassis Charge 6.15 CHASSIS- CHRG Handling charge for customer supplied chassis $2,953.00

10 Aerial Units Contract end Date Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip Bloomington, MN Phone #: Toll Free #: Fax #: Address: Website: Version of Excel used: Aerial Units Make Altec Warranty 1 year parts and labor Date & I.D. of Price List 12/1/2017 Altech Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed CVI Inspection Please See Pricing Below Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address 9150 Pillsbury Avenue South, Bloomington, MN Price per loaded mile for delivery $4.50 Delivery Time Frame in calendar days ARO Determined at time of order Shop Rates Shop Rate for Mechanical work $ Body Shop Rate $ *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage 12/1/2017 Altech 6.01 Altec AT37G Altec AT37G Installed Altec Model AT37G telescoping/articulating continuous rotation aerial device $62, ALTEC Model AT37G telescoping/articulating continuous rotation aerial device with an insulating articulating arm, insulating telescopic

11 upper boom, and the patented ISO-Grip insulating system at the boom tip. Includes the following features: Build Install on customer supplied 60 CA Ford F550 or Dodge 5500 Ground to bottom of platform height: 37.8 feet Working height: 42.8 feet Maximum reach to edge of platform. Side Mounted Platform: 26.6 feet. End Mounted Platform: 28.3 feet (at 14.4 foot platform height). Telescopic boom extension: 9 feet 8 inches Continuous rotation Insulating Aerial Device, ANSI Category C, 46kV and Below Articulating Arm: Articulation is from -7 to 90 degrees. Insulator provides 12 inches of isolation. Compensation System: By raising the articulating arm only, the telescopic boom maintains its relative angle in relation to the ground. The work position is achieved through a single function operation. Telescoping upper boom: Articulation is from -25 to 75 degrees. Master/ Slave Leveling: Platform automatically maintains level during boom articulation through a lifetime master/slave hydraulic leveling system that requires no major preventive maintenance. The INSULATING UPPER CONTROL SYSTEM includes a single handle controller incorporating high electrical resistance components that is dielectrically tested to 40 kv AC with no more than 400 microampers of leakage. The control handle is green in color to differentiate it from other nontested controllers. One set of tool outlets at the platform providing up to 5 gpm of flow for open center tools Hydraulic System: Open center system operating at 5gpm and 2,400 psi. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion. Structural

12 Warranty all of the following applicable major components is to be warranted for so long as the initial purchaser owns the product: Booms, boom articulation links, hydraulic cylinder structures, outrigger weldments, pedestals, subbases and turntables. Manuals: Two (2) operator and Maintenance/Parts manuals AT37G Unit Model Engine Start/Stop & Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation wherein the primary hydraulic source fails. Electric motor is powered by the chassis battery. This feature allows the operator to completely stow the booms and platform. Secondary Stowage & Start/Stop is activated with an air plunger at the platform and switch at the lower control station. Post style pedestal mounting Poly Hydraulic Reservoir, Pedestal Mounted, 7 Gallon (Includes Sight Gauge) Single, One (1) Man, Fiberglass Platform; End Mounted with 180 degree rotator. 24 x 30 x 42 inches, includes hydraulic tilt. One (1) Platform Step Soft nylon reinforced vinyl platform cover for a 24 x 30 inch platform Platform liner for a 24 x 30 x 42 inch platform Platform Capacity, 400LBS. Altec Patented ISO-Grip Insulating 4 Function, Proportional Speed, Upper Control Handle - with safety interlock and interlock guard. Forward/back operates upper boom in/out, tiller operates rotation CW/CCW, up/down operates lower boom up/down, and twist operates articulating arm up/down. Platform leveling is controlled with a separate interlocked control handle. Manual lowering valve located at the boom tip. For use in emergency situations to allow the operator to lower the boom to the ground

13 Powder coat unit Altec White. Unit & Hydraulic Acc. HVI-22 Hydraulic Oil (Standard). Standard Pump For PTO Hot shift PTO for automatic transmission Body 108 Inch Universal Small Aerial Body for a 60 Inch CA Chassis with 38 Inch Long Side Access Tailshelf to Meet the Following Specifications: Basic body fabricated from A40 grade 100% zinc alloy coated steel All doors are full, double paneled, self-sealed with built-in drainage. Electro-zinc plated, steel hinge rods extend full length of door. Door hinges are zinc alloy material attached with rivets All doors contain stainless steel, flush mounted, paddle activated rotary style latches with two-stage locking, including keyed locks and adjustable strikers. Heavygauge welded steel frame construction with smooth galvaneal floor. All edges are either rolled or folded for strength and safety Door header drip rail at top for maximum weather protection. Neoprene or rolled fenders on wheel fender panels. Steel treated for improved primer bond and rust resistance. Automotive underseal applied to body. Automotive type non-porous door seals fastened to the door facing. 108 Inch Body Length 40 Inch Body Height (Standard) 94 Inch Body Width (Standard) 20 Inch Body Compartment Depth (Standard) Body Color - White (Standard) Finish Paint Body At Body Manufacturer (Standard) 8 Inch Body Cross-members (Standard) No Treadplate On Compartment Tops 6 Inch tall wood tailboard installed at the rear of body cargo area No Compartment Lighting Supplied by the Body Manufacturer Stainless Steel Rotary Paddle Latch With Lock (Standard) Master Body Locking System (Standard) No Chock Holders In Line Body Fender Panel Required

14 (Standard) Gas Shock Type Rigid Door Holders For Vertical Doors (Standard) Chains On Horizontal Doors Hotstick shelf extending full length of body on curbside. Drop-Down Hot Stick Door For One (1) Shelf (Right Side) Two (2) Hot Stick Brackets 1st Vertical Street Side (LH) - Two (2) Adjustable Shelf With Removable Dividers On 4 Inch Centers 1st Horizontal Street Side (LH) - One (1) Fixed Shelf With Removable Dividers On 8 Inch Centers Rear Vertical Street Side (LH) - Six (6) Adjustable Locking Swivel Hooks 1st Vertical Curb Side (RH) - Seven (7) Adjustable Locking Swivel Hooks, Louvered Panel Installed in Cargo Wall 1st Horizontal Curb Side (RH) - Vacant Rear Vertical Curb Side (RH) - Two (2) Adjustable Shelf With Removable Dividers On 4 Centers Aluminum Rock Guards Installed at Bottom 38" Tailshelf with Integrated Side Access Steps, Two Wheel Chock Holders, and Smooth Galvaneal Floor Installed at Rear of Body Body and Chassis Accessories ICC Underride Protection Combination 2 Ball (10,000 LB MGTW) And Pintle Hitch (16,000 LB MGTW) Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. Rear Torsion Bar Installed On Chassis Appropriate counterweight added for stability. Platform Rest, Rigid with Rubber Tube Boom Rest for a Telescopic Unit Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers Safety Harness And 4.5' Lanyard (Fits Medium To X-large) Includes Pouch and Placards 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Vinyl manual pouch for storage of all operator and parts manuals Electrical

15 Accessories Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including LED reverse lights) Standard Amber LED Strobe Light With Brush Guard Post Mounted On Streetside Front Compartment Top Single tone back up alarm installed between the chassis frame rails at the rear of the chassis. To work in conjunction with chassis reverse drive system 6-Way Trailer Receptacle (Pin Type) Installed At Rear Dash panel rocker switches supplied with Chassis. Auxiliary switches supplied in upfitting package from chassis. Start/Stop/Throttle Module, 12 Volt System Install secondary stowage system. PTO Indicator Light Installed In Cab Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated black by Altec. Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Focus Factory Build Install on customer supplied 60 CA Ford F550 or Dodge 5500 Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90) days warranty for travel charges, limited lifetime structural warranty F.O.B. Bloomington, MN Altec AT37G Options Installed 6.02 OUTRIGGERS IN LIEU OF TORSION BAR $2, AT40G (INCLUDES 2ND TORSION BAR) $9, STANDARD STEEL 84 CA BODY $5, FIBERGLASS 60 CA BODY $2, FIBERGLASS 84 CA BODY $9,887.00

16 FT. MATERIAL HANDLING VERSION WITH 84 STANDARD STEEL BODY $24, STANDARD BODY COMPARTMENTATION RECONFIGURATION $ Altec LR7-56 Altec LR7-56 Installed Altec Model LR7-56 Articulating Overcenter Aerial Device $82, ALTEC Model LR7-56 Articulating Overcenter Aerial Device with an insulating lower boom, insulating upper boom and the Altec ISO-Grip insulating system at the boom tip. Installed behind the cab to include the following features: Installed on customer supplied medium duty chassis, must be approved by Altec prior to order Ground to Bottom of Platform Height: 56.3 feet (17.16 meters). Working Height: 61.3 feet (18.68 meters). Maximum reach to edge of platform with Upper Boom Nonovercenter: 41.6 feet (12.68 meters). Maximum reach to edge of platform with Upper Boom Overcenter: 44.4 feet (13.53 meters). Continuous rotation. Lower Boom Articulation: 0 to 125 degrees. Lower Boom Insulator provides 15 inches (38.1 centimeters) of isolation. Upper Boom Articulation: 0 to 270 degrees. Platform capacity: 400 lbs ( kilograms). Platform leveling: achieved by a single leveling chain and 3/4" fiberglass rods in the upper and lower booms. This lifetime system is very low maintenance. Hydraulic system: Open center (full pressure), maximum flow of 6.0 to 6.5 gpm (22.7 to 24.6 lpm), maximum operating pressure of 3,000 psi. Side-by-Side Boom Stow offers low travel height and easy platform access. Maintenance Free Elbow: nitrided to prevent rust, increase hardness and eliminates the need for grease at the elbow Small Boom Tip Profile. Altec Patented walking link system features uniform speed, smooth and continuous articulation

17 and low maintenance operation. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion. Paint is electrostatically applied to the inside as well as outside of fabricated parts then high temperature cured prior to assembly ensuring maximum coverage and protection. Unit meets or exceeds ANSI 92.2 standards. Manual Upper Boom Stow Securing System with support cradle and tie down strap. Pedestal Reservoir, 30 Gallon Sight Gauge for Hydraulic Reservoir, Remote Mounted Single, One (1) Man, Fiberglass Platform; fixed side mounted. 24 x 24 x 39 inches. Altec Patented ISO-Grip Insulating, Proportional Speed, Upper Control Handle with safety interlock and interlock guard. Located on the side of the platform nearest the upper boom, mounted on the shaft. Forward/back operates lower boom down/up, tiller operates rotation CW/CCW, and up/down operates upper boom up/down. One (1) Platform Step Located on the side of the platform nearest the elbow in the stowed position Platform Cover - Soft vinyl 24 x 24 inch (610 x 610 mm) Platform Liner, 24 x 24 x 39 inches (610 x 610 x 991 mm), 50 kv Rating Platform Floor Liner (Scuff Pad), 24 x 24 inches (610 x 610 mm) Hydraulic Tool Circuit at Platform: Two (2) sets of tool couplers for open center tools, located on the side of the platform nearest the elbow in the stowed position. Tool Circuit System Relief Pressure to be set to 2250 PSI Primary A-Frame Outriggers with 5- degree swivel shoe. For installation on a 36 to 40 inch chassis frame height. Maximum Spread: 140 inches to the outer edge of shoes Ground

18 Penetration: 7 to 11 inches depending on chassis frame height Outrigger/Unit Selector Valve Outrigger Control Valves: located on the outrigger legs Outrigger Motion Alarms Outrigger Interlocks: will not allow the unit to be operated until the outriggers have been at least partially deployed Hydraulic Outrigger Control Valves Insulating Aerial Device, ANSI Category C, 46kV and Below Fall Protection System to include one body harness and decelerating type lanyard. Bolt On Grab Handle for Turntable Altec Aerial Device Powder Painted White Unit & Hydraulic Acc. HVI-22 Hydraulic Oil (Standard). Standard Pump For PTO Hot shift PTO for automatic transmission Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear. Once the chassis is shifted back into gear the PTO will disengage. For some truck configurations the PTO switch must be turned off to allow the transmission to shift into gear. Body Altec Chip Dump Body 14.5 cubic yard capacity, 96 inches wide x 60 inches high x 132 inches long (2438 x 1524 x 3353 mm) with ladder box on curb side of body and single piece tailgate Structural Channel stringers and floor channel. 12 gauge minimum floor plate. 14 gauge minimum sides and front with full length die-formed reinforcing ribs. 14 gauge roof. Rear top and sides of body reinforced for lower boom support. 26-1/2 inches (673 mm) high tailgate, hinged curb side with provision to hold open for dumping. 12 gauge minimum rear under body skirt panel. Class ''C'' Hydraulic hoist, installed, with 45 degree dump angle and body prop.

19 LED lighting package, security-mounted, with wiring harness in automotive type loom. Two(2) LED strobes mounted in the upper rear corners of the dump body. Curb side built-in ladder compartment, 12 inches wide x 25 inches high (305 x 635 mm) with wear pad and internal security chain. Pole pruner compartment, 11 inches high (279.4 mm), above ladder compartment with dual shelves and rear locking door. Upper section of rear door opening is open. Interior of chip body finished with scratch and corrosion resistant liner Underside of chip body undercoated. Painted White Altec T-48 Thru Box tool compartment 48 inches wide x 50 inches high x 96 inches long (1219 x 1270 x 2438 mm) with 26.5 inch (673 mm) deep curb and street side compartments with the following compartmentation Streetside: Single compartment with two vertical barn-style doors. Left side has two (2) fixed shelves with six (6) dividers. Right side has four (4) unequal transverse compartments open to curbside. Compartment bottom has one (1) tray with five (5) removable dividers, inch (3.175 mm) rubber liner partitioned for chainsaw gas can and wedge storage. Security chain for chainsaw provided in bottom and wedge storage. Security chain for chainsaw provided in bottom. Curbside: Single compartment with two (2) vertical barn-style doors. Left side has four (4) unequal transverse compartments open to streetside. All compartments have inch (3.175 mm) rubber shelf liners. Top center has two (2) fixed shelves with six (6) dividers. Top right has six (6) swivel rope hooks (3-0-3). Compartment bottom has one (1) tray with five (5) removable dividers, inch (3.175 mm) rubber liner

20 partitioned for chainsaw gas can and wedge storage. Security chain for chainsaw provided in bottom. Standard features: Bolton rotary slam door locks. Gas shock door holders. Door locks are two point engagement with locking cylinders. Finish paint interior compartments the same as exterior. Integrated locking system installed. Single drawer kit mounted under fixed shelves. Painted White Body and Chassis Accessories Cab Guard, 140'' L, 12 GA Sheet Metal With Non-Skid Surface And Expanded Metal Section At Front, Black Gator Hyde Coating Cab Guard Mounting Kit Front Supports For Cab Guard ICC (Underride Protection) Bumper Installed At Rear T-100 Style Pintle Hitch (30,000 LB) Set of Safety Chain Loops, Fixed Mounting (Forestry Applications) Cab Guard Access Stirrup Step(s) With Grab Handle(s) At Curbside Rear Of Cab Guard Cab Guard Access Ladder Platform Rest, Rigid with Rubber Tube Wood Outrigger Pad, 19.5'' x 19.5'' x 2.25'', With Fluorescent Orange Steel Collar Around The Outer Edges And Chain Handle Outrigger Pad Holder, 20" L x 20" W x 3.5" H, Fits 19.5" x 19.5" x 2.25" And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4" Lip Retainer Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle (Pair) Wheel Chock Holders (Pair), For Installation Under Flatbed Or Dump Body Slope Indicator Assembly For Machine With Outriggers Cone Holder, Horizontal Style with Vertical Pivot (Un-folds Upwards), For Mounting On Front Bumper (Holds up to four 15"x15" large cones) Driveaway Safety Kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Strobe and Indicator Lights Wired Battery Hot Lights And Reflectors Per FMVSS 108 (Complete LED),

21 With Security Mounted Lights 4-Corner Strobe Lighting, Amber LED Two (2) Round Security Mounted Lights in Front Corners of Cab Guard Two (2) Round Security Mounted Lights at Rear Dual Tone Back-Up With Outrigger Motion Alarm 6-Way Trailer Receptacle (Pin Type) Installed At Rear Electric Trailer Brake Controller (Tekonsha Voyager #9030) Install Outrigger Interlock System Altec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory Switches PTO Indicator Light Installed In Cab Finishing Details Powder Coat Unit White Finish Paint Body Accessories Above Body Floor Altec White Components mounted below frame rail shall be coated black Vehicle Height Placard, Installed In Cab Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Focus Factory Build Installed on customer supplied medium duty chassis, must be approved by Altec prior to order Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90) days warranty for travel charges, limited lifetime structural warranty F.O.B. Bloomington, MN Altec LR7-56 options Installed 6.1 Upgrade to LR7-58 $1, Upgrade to LR7-60 $4, Upgrade to rear mount version $11, HOP Hydraulic Overload Protection System (Elliott # ) $3,875.00