Figs. 800 Verticle, 800 W. Fig. 800 Vertical Type Fig. 800 W. Wall type.

Size: px
Start display at page:

Download "Figs. 800 Verticle, 800 W. Fig. 800 Vertical Type Fig. 800 W. Wall type."

Transcription

1 Indicator Posts Indicator posts are controls, extending aboveground, for operating underground sprinkler system valves. As an important feature of their design, a target or indicator, visible through an opening in the post, shows whether the valve is open or shut. The indicator post generally consists of a cast iron barrel, an extension flange which allows the height of the barrel to be regulated, and a wrought iron or mild steel stem which operates the underground valve and simultaneously moves the target. A telescoping union permits turning the stem from a constant height. Indicator posts are available for installation on non-rising stem gate valves. Unless otherwise specified, indicator posts are Approved for use on 4 through 14 in. NPS non-rising stem gate valves with an indicator post flange. In all new fire protection system installations, buried valves must open in a counterclockwise direction regardless of the direction the valves of the public water system open. An exception to this is when all other buried valves in a plant yard open in a clockwise direction. Then all new valves should open clockwise also. When some buried valves in a system open one way and some the other, all new valves should open counterclockwise. There may be exceptions to this when most valves in an extensive yard system open clockwise. In such cases, FM Global should be consulted regarding the proper direction of opening. Figs. 800 Verticle, 800 W Fig. 800 Vertical Type Fig. 800 W. Wall type.

2 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 762U Model 762U. Metal to Metal Seated Gate Valve. 2 through 12 in. NPS. 175 psi (1205 kpa) rated working pressure. Available with the 2, 2 1 2, 3, 4, 6, 8, 10, 12 Flanged

3 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 722U Model 722U. Resilient Seated Gate Valve through 12 in. NPS. 200 psi (1380 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged

4 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 722H Model 722H. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged

5 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 710U Model 710U. Metal to Metal Seated Gate Valve through 12 in. NPS. 175 psi (1205 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged 2 1 2, 3, 4, 6, 8, 10, 12 Mechanical Joint

6 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 721F Model 721F. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged x Flanged

7 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 721G Model 721G. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Grooved

8 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 721GF Model 721GF. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. All valves are available with an operating nut or indicator post flange with operating nut. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Grooved x Flanged

9 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 721H Model 721H. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged 2 1 2, 3, 4, 6, 8, 10, 12 Mechanical Joint

10 Inside Screw Gate Valves Inside screw gate valves are used underground with indicator posts attached or as roadway box valves (curb box installation). FM Approved valves are available with a variety of end connections as indicated in the listings. Valves having Ring-Tite, Fluid-Tite or Tyton-Joint connections should be anchored in place during installation. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 721U Model 721U. Resilient Seated Gate Valve through 12 in. NPS. 200 psi (1380 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged 2 1 2, 3, 4, 6, 8, 10, 12 Mechanical Joint

11 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 722F Model 722F. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Flanged x Flanged

12 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 722G Model 722G. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Grooved

13 Outside Screw and Yoke Gate Valves Outside screw and yoke gate valves are recommended for service indoors and in pits outdoors. They are not recommended for throttling service. The stem indicates at a glance whether or not the valve is open. Smaller sizes, 3 4 through 2 in. NPS inclusive, are of bronze. Large sizes, through 14 in. NPS inclusive, are of iron, bronze mounted. One manufacturer makes valves of bronze up through the 3 in. size. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. Model 722GF Model 722GF. Resilient Seated Gate Valve through 12 in. NPS. 250 psi (1725 kpa) rated working pressure. Available with the 2 1 2, 3, 4, 6, 8, 10, 12 Grooved x Flanged

14 Single Check Valves Single check valves are used in fire protection systems to allow waterflow in one direction only. Typical applications are at connections between public water supplies and private fire service systems, at the discharge from fire pumps, at gravity tank connections and at fire service pumper connections. Valves identified in the listing by a single asterisk (*) have side covers; valves identified by a double asterisk (**) have no removable covers; others have top covers. Clearance must be provided for side-cover valves to permit clapper removal. Valves without covers must be removed from the system for clapper replacement or repair. Unless otherwise noted in the listing, these valves have 175 psi (1205 kpa) rated working pressure. 763U, 453U Product Designation Description Nominal Pipe Size, in. Max Working Pressure, psi (kpa) Remarks 763UM Swing Check Valve Flanged Ends 3, 4, 6, 8, 10, (1380) a 763UR Swing Check Valve Flanged Ends 3, 4, 6, 8, 10, (1380) b 453UF Dual Plate Check Valve Flanged Ends 3, 4, 6, (1725) b, c 453UG Dual Plate Check Valve Grooved Ends 3, 4, 6, (1380) b, c Remarks a. Metal seat. b. Resilient seat. c. No removable covers.

SUBMITTAL PACKAGE FIRE PROTECTION VALVES

SUBMITTAL PACKAGE FIRE PROTECTION VALVES SUBMITTAL PACKAGE FIRE PROTECTION VALVES Butterfly Valves Ductile Iron Grooved...pg 2-5 Grooved Check Valves...pg 6-8 OS&Y Valves...pg 9-12 ARGCO.com 800-854-1015 Updated 2/27/2017 ARGCO GROOVED BUTTERFLY

More information

ESCONDIDO FIRE DEPT TRAINING MANUAL Section Engine Module Page 1 of 5 Sprinkler System Controls Revised

ESCONDIDO FIRE DEPT TRAINING MANUAL Section Engine Module Page 1 of 5 Sprinkler System Controls Revised Engine Module Page 1 of 5 SPRINKLER SYSTEM CONTROLS Control and Operating Valves Integral to each sprinkler system is the main control valve. These valves are used to shut off the supply of water when

More information

According to AWWA-standard

According to AWWA-standard According to -standard Water Fire fighting - UL/FM 304 Gate valves - Cast iron 320 Gate valves OS&Y 306 Service connection valves 322 Post indicators 306 Combi valves 307 Gate valves - 310 Gate valves

More information

PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA

PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending

More information

SECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping.

SECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping. SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Section includes valves for building services piping. 1.2 REFERENCES A. AGA Z21.22 (American Gas Association) - Relief Valves

More information

Valve Selection. 1. Function and service considerations

Valve Selection. 1. Function and service considerations 1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.

More information

Approved Branded Traceable Fire Protection & Waterworks Valves

Approved Branded Traceable Fire Protection & Waterworks Valves Approved Branded Traceable Fire Protection & Waterworks Valves (800) 766-0076 www.smithcooper.com Los Angeles, CA Atlanta, GA Vancouver, WA Chicago, IL AWWA C515 Compliant CONSIDER Your Options Tamper

More information

Technical Data. Sizes 2 in. to 24 in. (DN50 to DN600) Approvals UL and ULC Listed FM Approved

Technical Data. Sizes 2 in. to 24 in. (DN50 to DN600) Approvals UL and ULC Listed FM Approved Worldwide Contacts www.tyco-fire.com Model TJP Resilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator General Description TYCO Model TJP Resilient-Seated Gate Valves with Vertical and

More information

Fire Protection Indicator Post

Fire Protection Indicator Post The 813 Series Indicator Post is designed to operate non-rising stem gate valves used in the control of underground water supply for automatic sprinklers, water spray deluge, foam-water deluge, and standpipe

More information

visit us online at

visit us online at PRICE SHEET (PL-1014-VLV Replaces PL-0513-VLV) TABLE OF CONTENTS VALVES & HYDRANTS Page(s) Product Line Price Sheet 1 AWWA C515 Gate Valves NRS Series 2010 & 1010 PL-1014 Multiplier 2 AWWA C515 Gate Valves

More information

PIPE OUTSIDE DIAMETER GUIDE

PIPE OUTSIDE DIAMETER GUIDE June 7, 2018-1 PIPE OUTSIDE DIAMETER GUIDE PIPE OUTSIDE DIAMETER GUIDE - SMALL DIAMETER PIPE SIZES NOMINAL PIPE SIZES 1 /2" 3 /4" 1" 1 1 /4" 1 1 /2" 2" 2 1 /2" THIS O.D. GUIDE IS FOR YOUR CONVENIENCE &

More information

Copyright 2012 AIA MasterSpec Premium 06/12 PRODUCT MASTERSPEC LICENSED BY ARCOM TO CONBRACO, INC.

Copyright 2012 AIA MasterSpec Premium 06/12 PRODUCT MASTERSPEC LICENSED BY ARCOM TO CONBRACO, INC. This Product MasterSpec Section is licensed by ARCOM to Apollo Flow Controls, Conbraco Industries, Inc ("Licensee").This Product MasterSpec Section modifies the original MasterSpec text and does not include

More information

KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES

KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES KENNEDY VALVE AWWA C515 Resilient Wedge Gate Valves Meet or Exceed the Requirements of AWWA Standard C515 UL-262/FM-1120/1130 ULC-Underwriters of Canada 2 1/2

More information

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3

SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3 SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General 430-1 thru 430-2 2. Gate Valves 430-2 thru 430-3 3. Plug Valves 430-3 thru 430-4 4. Check Valves 430-4 5. Tapping

More information

mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY

mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY 129 HYDRANT YESTERDAY, TODAY, & TOMORROW For more than 85 years, the M&H

More information

MEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY

MEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY clowvalve.com MEDALLION HYDRANT AWWA C50 UL LISTED FM APPROVED NSF 6/37 CERTIFIED 50 PSI WORKING PRESSURE 0-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane, Inc. MEDALLION HYDRANT FIRE PROTECTION

More information

INSTALLATION, OPERATION, and MAINTENANCE GUIDE NIBCO Wall Mount Indicator Posts Series NIP-2AW

INSTALLATION, OPERATION, and MAINTENANCE GUIDE NIBCO Wall Mount Indicator Posts Series NIP-2AW INSTALLATION, OPERATION, and MAINTENANCE GUIDE NIBCO Wall Mount Indicator Posts Series NIP-2AW PATENT #US 9,541,218 NIBCO Series NIP-2AW Wall Mount Indicator Posts are designed and manufactured to: Operate

More information

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS

San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance

More information

San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS

San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance

More information

Shearseal Knife Gate Valves. Manufactured by TSE

Shearseal Knife Gate Valves. Manufactured by TSE Shearseal Knife Gate Valves Manufactured by TSE Shearseal Design Most knife gate valve manufacturers describe their valve as rugged and dependable. In the Shearseal Valve, these qualities are not idle

More information

Approved. Size L H. 3" (76mm) 9-1/2" (241mm) 5-51/64" (147mm) 46. 4" (102mm) 11-1/2" (292mm) 6-45/64" (170mm) 81

Approved. Size L H. 3 (76mm) 9-1/2 (241mm) 5-51/64 (147mm) 46. 4 (102mm) 11-1/2 (292mm) 6-45/64 (170mm) 81 pproved. Model: SD-NRV200CV Flanged Ends The Flanged End Check Valves are made of Iron Body, Bolted Bonnet and Horizontal Swing, painted with standard color. Epoxy coated inside and outside to WW C550

More information

OPTIMAL VALVE SOLUTIONS FOR OIL AND GAS PLANTS

OPTIMAL VALVE SOLUTIONS FOR OIL AND GAS PLANTS AVK FLOW CONTROL OPTIMAL VALVE SOLUTIONS FOR OIL AND GAS PLANTS InterApp World Valve Wouter Witzel TEC artec AVK 1 2 AVK FLOW CONTROL l OIL & GAS PLANTS CONTENT: AVK FLOW CONTROL 4-5 OFFSHORE PRODUCTION

More information

A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.

A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems. SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing

More information

ADMIRAL HYDRANT. clowvalve.com

ADMIRAL HYDRANT. clowvalve.com clowvalve.com ADMIRAL HYDRANT AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 350 PSI WORKING PRESSURE AVAILABLE 10-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane,

More information

FireLock NXT Deluge Valve. With Deluge Trim Grooved x Grooved. System No. Submitted By Spec Sect Para Location Date Approved Date

FireLock NXT Deluge Valve. With Deluge Trim Grooved x Grooved. System No. Submitted By Spec Sect Para Location Date Approved Date MEA: 248-98-E CSFM: 7770-0531-117 The patent-pending Victaulic Series 769 FireLock NXT controls the water supply entry into the deluge system piping and open sprinklers. The Series 769 is a low differential,

More information

MODEL UM UNIVERSAL MANIFOLD ASSEMBLY (With or Without Control Valve) 1¼", 1½", 2", 2½", 76.1mm, 3", 4", 6",165.1mm, 8"

MODEL UM UNIVERSAL MANIFOLD ASSEMBLY (With or Without Control Valve) 1¼, 1½, 2, 2½, 76.1mm, 3, 4, 6,165.1mm, 8 4077 Airpark Dr. Standish, MI 48658 989-846-4583 www.globesprinkler.com Technical Support 989-414-2600 techservice@globesprinkler.com MODEL UM UNIVERSAL MANIFOLD ASSEMBLY (With or Without Control Valve)

More information

GENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Iron swing check valves. 3. Iron gate valves. 4. Iron globe valves. B.

More information

Crispin Valves Operating Guide. Crispin

Crispin Valves Operating Guide. Crispin Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com

More information

NON RETURN BRASS FLANGED AGA GAS APPROVED

NON RETURN BRASS FLANGED AGA GAS APPROVED NON RETURN BRASS FLANGED AGA GAS APPROVED ACTUATED MARINE STAINLESS STEEL 34 VALVES 36... BRASS BALL VALVES 37... AGA GAS APPROVED VALVES GATE VALVES 38... BRASS VALVES 39... RUBBER BELLOW, HOSECOCKS &

More information

M&H AWWA C508 STANDARD SWING CHECK VALVES

M&H AWWA C508 STANDARD SWING CHECK VALVES GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by

More information

VALVES, FIRE HYDRANTS, AND APPURTENANCES

VALVES, FIRE HYDRANTS, AND APPURTENANCES VALVES, FIRE HYDRANTS, AND APPURTENANCES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Butterfly Valves B. Gate Valves C. Tapping Valve Assemblies D. Fire Hydrant Assemblies E. Flushing Devices (Blowoffs)

More information

GD N (not shown) No Switches. GD N Grooved 2¹ ₂", 3", 4", 6", 8", 10"

GD N (not shown) No Switches. GD N Grooved 2¹ ₂, 3, 4, 6, 8, 10 300 PSI WWP UL/FM Butterfly Valves Designed for normally open position monitoring Elastomer Encapsulated Disc Accepts Internal Supervisory Switches Compatible with IPS Pipe 300 PSI/20.7 Bar Non-Shock Cold

More information

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page Page 220523-1 SECTION 220523 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

FACILITY WATER DISTRIBUTION PIPING

FACILITY WATER DISTRIBUTION PIPING SECTION 221113 - FACILITY WATER DISTRIBUTION PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL

AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION

More information

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page Page 230523-1 Copyright 2005 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical Plant

More information

V January 2016 SINGLE SEATED V5011 SERIES. Previously manufactured by Dezurik and Honeywell

V January 2016 SINGLE SEATED V5011 SERIES. Previously manufactured by Dezurik and Honeywell V5011. January 2016 SINGLE SEATED V5011 SERIES Previously manufactured by Dezurik and Honeywell Description: 2 ½ to 6 class 5 with cast iron body, bronze trim and composite seat, ideally suited for low

More information

AVK SAUDI VALVES MANUFACTURING COMPANY

AVK SAUDI VALVES MANUFACTURING COMPANY AVK SAUDI VALVES MANUFACTURING COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION

More information

GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101

GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101 GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101 Available Sizes 1" through 12" (25 through ) Pipe Material Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses

More information

SECTION VALVES PART 1 - GENERAL

SECTION VALVES PART 1 - GENERAL 1.01 RELATED DOCUMENTS SECTION 15100 VALVES PART 1 - GENERAL A. The work in this section includes the furnishing and installation of all control valves and accessories shown on the construction plans and

More information

Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC&R VALVES

Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC&R VALVES SECTION 23 05 23 HVAC&R VALVES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes valves for building services piping. 1.2 GENERAL VALVE APPLICATION REQUIREMENTS: A. Provide valve handle extensions that

More information

SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.

SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems. SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000

More information

GENERAL CATALOGUE Catalogue 2013

GENERAL CATALOGUE Catalogue 2013 GENERAL CATALOGUE Catalogue 2013 Company Profile GALA - Extends Business on a Global Perspective. GALA company offers a wide range of products and systems in the field of valves, piping, and seismic isolation

More information

AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL

AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL AMERICAN AVK COMPANY AVK SERIES 34 WALL MOUNTED & TELESCOPIC POST INDICATORS, UL LISTED, FM APPROVED FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION

More information

Instructions for Installation, Operation, Care and Maintenance

Instructions for Installation, Operation, Care and Maintenance Bulletin 59 Model DDX Deluge Valve (50 mm), ½ (65 mm), (80 mm), 76 mm, 4 (00 mm), 6 (50 mm), 65 mm & 8 (00 mm) Bulletin 59 Instructions for Installation, Operation, Care and Maintenance Wet Pilot Line,

More information

Division 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING

Division 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION FACILITY FUEL OIL PIPING

SECTION FACILITY FUEL OIL PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related Sections:

More information

FIRE PROTECTION PUMPS. Table of Contents

FIRE PROTECTION PUMPS. Table of Contents FM Global Property Loss Prevention Data Sheets 3-7 April 2012 Page 1 of 45 FIRE PROTECTION PUMPS Table of Contents Page 1.0 SCOPE... 3 1.1 Changes... 3 2.0 LOSS PREVENTION RECOMMENDATIONS... 3 2.1 Introduction...

More information

Series 769 FireLock NXT Deluge Valve

Series 769 FireLock NXT Deluge Valve IPS CARBON STEEL PIPE FIRE PROTECTION PRODUCTS Series 79 FireLock NXT Deluge Valve With Deluge Trim Grooved X Grooved 30.81 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION The patent-pending

More information

Model CV-1FR Grooved-End Riser Check Valves 2 Inch to 12 Inch (DN50 to DN300) General Description. Installation. Technical Data

Model CV-1FR Grooved-End Riser Check Valves 2 Inch to 12 Inch (DN50 to DN300) General Description. Installation. Technical Data Worldwide Contacts www.tyco-fire.com Model CV-FR Grooved-End Riser Check Valves Inch to Inch (DN0 to DN00) General Description The TYCO Model CV-FR Grooved- End Riser Check Valve is a compact and rugged

More information

Sentinel 250 Fire Hydrant. Solid design and features to meet any municipal requirement.

Sentinel 250 Fire Hydrant. Solid design and features to meet any municipal requirement. Sentinel 250 Fire Hydrant Solid design and features to meet any municipal requirement. Product Features That meet any municipal requirement. 1 Operating Nut Shields the hold down nut from tampering and

More information

SECTION VALVES. A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section.

SECTION VALVES. A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section. PART 1 GENERAL 1.01 DESCRIPTION OF WORK SECTION 22412 VALVES A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section. B. All valves, except those are 2 in diameter

More information

Herpteraium SECTION VALVES GENERAL

Herpteraium SECTION VALVES GENERAL SECTION 22 05 23 VALVES GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to

More information

Series 756 FireLock Dry System Check Valve

Series 756 FireLock Dry System Check Valve R IPS CARBON STEEL PIPE FIRE PROTECTION PRODUCTS Series FireLock Dry System Check Valve Grooved X Grooved and Flanged X Grooved 0.0 VICTAULIC IS AN ISO 900 CERTIFIED COMPANY PRODUCT DESCRIPTION The Victaulic

More information

with the specific application. Always read and understand the installation

with the specific application. Always read and understand the installation Worldwide Contacts www.tyco-fire.com Resilient-Seated Gate Valves Outside Screw and Yoke General Description TYCO Resilient-Seated Gate Valves are used in Fire Protection Systems for on/off operation.

More information

BS 5163 Resilient Wedge Gate Valve

BS 5163 Resilient Wedge Gate Valve BS 516 Resilient Wedge Gate Valve BS 516 Flanged Resilient OS&Y Gate Valve, Type A, (XZ41X), /16, Gate valves serve to cut the medium flow in the piping system, widely used in the field of potable water,

More information

1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves.

1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves. Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product

More information

A-C Fire Pump. Fitting and Accessories A-C 100A

A-C Fire Pump. Fitting and Accessories A-C 100A A-C Fire Pump Fitting and Accessories A-C 100A A-C Fire Pump Fitting and Accessories Table of Content Page Automatic Air Release Valve... 1 Suction And Discharge Gauge Assembly... 2 Casing Relief Valve...

More information

B. Work Included: The work shall include, but not be limited to, the following: 1. Types of valves specified in this section include the following:

B. Work Included: The work shall include, but not be limited to, the following: 1. Types of valves specified in this section include the following: SECTION 15100 - PART 1 - GENERAL 1.1 SUMMARY A. Provide labor, materials, equipment and services, and perform operations required for complete installation of Valves and related work as indicated on the

More information

M&H AWWA C508 STANDARD SWING CHECK VALVES

M&H AWWA C508 STANDARD SWING CHECK VALVES GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by

More information

Suggested Specifications

Suggested Specifications ISO 9001 Certified Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve, setting higher standards for dependable performance

More information

1 Visit for more details. Contact the Factory at

1 Visit  for more details. Contact the Factory at PACIFIC Fire Protection Solutions for Offshore and Onshore Applications Deluge Pressure Relief Pressure Reducing Level Control Solenoid Control Air Release and Check Valves 1 Visit www.cla-valpacific.com

More information

Henderson Engineers, Inc. SECTION GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS

Henderson Engineers, Inc. SECTION GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS SECTION 220523 - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS 1.1 SUMMARY A. This Section includes general duty valves common to most plumbing piping systems. 1. Special purpose

More information

The SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution

The SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution The Series Meets AWWA C-508-01 Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick,

More information

Sludge Dewatering and Odor Control at Plant 1 CONFORMED

Sludge Dewatering and Odor Control at Plant 1 CONFORMED 2. Fire Service Main Interior Piping from Exterior Service up to Fire Sprinkler Alarm Check Valve: a. Pipe: Schedule 40 galvanized steel. b. Fittings: Galvanized 150-pound malleable iron, screwed or Victaulic

More information

ND = Double Door, SEAT NBR ES = Center Guided Silent Check / EPDM NS = Center Guided Silent Check / NBR. Butterfly Valves, Seat in body.

ND = Double Door, SEAT NBR ES = Center Guided Silent Check / EPDM NS = Center Guided Silent Check / NBR. Butterfly Valves, Seat in body. MAS-WDI-1118 MAS W-Series Water Works / Fire Protection Valves ORDERING CODES Series XX = Valve Type X = CWP XX = Design Type XX = End Connection W = AWWA/UL/FM, 10 = Gate Valve A = 300 CWP RS = Rising

More information

Price Book - Section C Valves and Hose Equipment

Price Book - Section C Valves and Hose Equipment Effective Date Price Book - Kennedy Valves O.S.&Y. Gate Valve UL/FM Resilient Wedge w/ 3 4" Tap and Plug - Model #4068A 2 2" 2265 $579.00 3" 2266 $669.00 4" 2267 $776.00 6" 2269 $,30.00 8" 2268 $,855.00

More information

SPECIFICATIONS - DETAILED PROVISIONS Section Valve and Gate Operations CONTENTS

SPECIFICATIONS - DETAILED PROVISIONS Section Valve and Gate Operations CONTENTS SPECIFICATIONS - DETAILED PROVISIONS Section 13446 - Valve and Gate Operations CONTENTS PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 SUBMITTALS... 1 1.04 QUALITY ASSURANCE... 1 1.05

More information

Data Sheet Issue A

Data Sheet Issue A General Description The Rapidrop Fig 601/602 dry barrel post / flushing fire hydrant is designed to be a trouble free, easy to maintain hydrant. The Fig 601/602 fire hydrant is rated for a working pressure

More information

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE ISO 9001 CERTIFIED MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve,

More information

Water Distribution Solutions

Water Distribution Solutions Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents

More information

SECTION (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS

SECTION (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS SECTION 22 11 23.13 (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Packaged Domestic Water Booster Pumps B. Related Sections: 1.02 REFERENCES 1. Section

More information

SECTION VALVES

SECTION VALVES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:

More information

Price Book - Section C Valves and Hose Equipment

Price Book - Section C Valves and Hose Equipment Kennedy Valves O.S.&Y. Gate Valve UL/FM Resilient Wedge w/ 3 /4" Tap and Plug - Model #4068A 2 1 /2" 2265 $743.00 3" 2266 $858.50 4" 2267 $996.00 6" 2269 $1,449.00 8" 2268 $2,379.00 10" 2264 $3,891.00

More information

M x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator

M x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator Installation Instructions Issue Date June 15, 2007 Supersedes November 15, 2002 M9000-53x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator Installation Parts Included

More information

K81-DD FIRE HYDRANT GUARDIAN AWWA C502 NSF YEARS. For Generations CERTIFICATIONS ISO 9001 ISO BS OHSAS

K81-DD FIRE HYDRANT GUARDIAN AWWA C502 NSF YEARS. For Generations CERTIFICATIONS ISO 9001 ISO BS OHSAS GUARDIAN K81-DD FIRE HYDRANT CERTIFICATIONS ISO 9001 ISO 14001 BS OHSAS 18001 AWWA C502 NSF 61 140 YEARS WWW.KENNEDYVALVE.COM C For Generations COMPONENTS AND FEATURES A B C E D F G H J K M L N P Q S R

More information

AMERICAN AVK COMPANY AVK SERIES 67 - HIGH PRESSURE, POST/FLUSHING HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS

AMERICAN AVK COMPANY AVK SERIES 67 - HIGH PRESSURE, POST/FLUSHING HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS AMERICAN AVK COMPANY AVK SERIES 67 - HIGH PRESSURE, POST/FLUSHING HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION RECEIVING

More information

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number: SECTION 230523 GENERAL DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. The following

More information

Iron Check Valves Illustrated Index

Iron Check Valves Illustrated Index Iron Check Valves Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Iron Body Silent Check

More information

FIRE PROTECTION PRODUCTS

FIRE PROTECTION PRODUCTS SUPER CENTURION FIRE HYDRANT Mueller Super Centurion Fire Hydrant Since its introduction in 1976, millions of Centurion fire hydrants have been installed throughout North America. There are a number of

More information

AUTOMATION ACCESSORIES IN-PLANT VALVE PRODUCTS EXTENSION STEMS FLOORBOX STEM GUIDES FLOORSTANDS COMMITTED TO ENVIRONMENTAL RESPONSIBILITY FLAP VALVES

AUTOMATION ACCESSORIES IN-PLANT VALVE PRODUCTS EXTENSION STEMS FLOORBOX STEM GUIDES FLOORSTANDS COMMITTED TO ENVIRONMENTAL RESPONSIBILITY FLAP VALVES INCREASING SWING CHECK VALVES FLAP VALVES SWING CHECK VALVES AUTOMATION ACTUATION CLOW VALVE has furnished valves with many assorted types of motorized to operate our valves. The gate valves use multi-turn,

More information

DIMENSIONS (approximate)

DIMENSIONS (approximate) Page 1 of 8 a NRS GATES OS&Y GATES company Model 48 Resilient Wedge Gate Valve SPECIFICATION SUBMITTAL SHEET FEATURES Sizes: 2 1/2" 3" 4" 6" 8" 10" 12" Maximum working water pressure 200 PSI Maximum working

More information

ACE VALVE COMPANY LIMITED

ACE VALVE COMPANY LIMITED Gate & Globe Valves ACE COMPANY LIMITED ttp://www.acevalve.co.kr Mangdeokri, Juchonmyun, Gimhae, Gyeongnam, Korea. TEL +000 FAX +0~ Email acevalve@acevalve.co.kr omepage www.acevalve.co.kr 0.0. ACE CATALOG

More information

AMERICAN AVK COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS

AMERICAN AVK COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS AMERICAN AVK COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION RECEIVING AND

More information

1.2 REFERENCES.1 American National Standards Institute (ANSI)/ American Society of Mechanical Engineers (ASME)

1.2 REFERENCES.1 American National Standards Institute (ANSI)/ American Society of Mechanical Engineers (ASME) Issued 2005/06/01 Section 15111 Valves Bronze Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards Institute (ANSI)/

More information

Instructions for Installation, Operation, Care and Maintenance

Instructions for Installation, Operation, Care and Maintenance Model D Dry Pipe Valve Bulletin 350 Rev. S Bulletin 350 Rev. S Instructions for Installation, Operation, Care and Maintenance 4 (100mm) 6 (150mm) Valve With Model D Trimmings Listed by Underwriters Laboratories,

More information

VALVE AND HYDRANT PRICE BOOK

VALVE AND HYDRANT PRICE BOOK VALVE AND HYDRANT PRICE BOOK HTTP://WWW.CLOWVALVE.COM EFFECTIVE DATE February 10, 2012 CLOW VALVE COMPANY 902 SOUTH SECOND ST. OSKALOOSA, IA 52577 PH# 800-829-2569 FAX# 641-673-8269 CLOW VALVE COMPANY

More information

SECTION VALVES PART 1 -GENERAL

SECTION VALVES PART 1 -GENERAL SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This

More information

Keystone resilient seated butterfly valves Figure 221 and 222

Keystone resilient seated butterfly valves Figure 221 and 222 Figure 221 and 222 An economical bonded resilient seated butterfly valve for bi-directional and end-of-line service F221 Wafer style valve F222 Lugged style valve Features Bubble tight shut-off at full

More information

M x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators

M x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators Issue Date June 15, 2007 Supersedes November 15, 2002 M9000-53x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators Installation Parts Included Linkage Stem

More information

A. This Section includes general duty valves common to several HVAC piping systems.

A. This Section includes general duty valves common to several HVAC piping systems. SECTION 23 05 23 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

Flow controller (PN 25) AVQ - return and flow mounting

Flow controller (PN 25) AVQ - return and flow mounting Data sheet Flow controller (PN 5) - return and flow mounting Description is a self-acting flow controller primarily for use in district heating systems. The controller closes when set max. flow is exceeded.

More information

InsertaValve Sleeve. InsertaValve Valve Assembly. Valve Insertion, simplified. Material Specifications. Transmate InsertaValve

InsertaValve Sleeve. InsertaValve Valve Assembly. Valve Insertion, simplified. Material Specifications. Transmate InsertaValve Material Specifications Material Specifications Sleeve 10" - 12" installations in cast iron, ductile iron, A/C, PVC C-900 and steel pipe No Loss of Pressure Minimal Water Loss Completion time is less than

More information

Water Distribution Solutions

Water Distribution Solutions Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents

More information

SECTION (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING

SECTION (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING SECTION 22 05 23 (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Valves. B. Related Sections: 1.02 REFERENCES 1. Section 22 05 53 (15075) Identification

More information

TABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44

TABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44 TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical

More information

Valves. BS Standard JINAN MEIDE CASTING CO., LTD.

Valves. BS Standard JINAN MEIDE CASTING CO., LTD. Valves BS Standard JINAN MEIDE CASTING CO., LTD. Resilient Wedge Gate Valve XZ81X Grooved Resilient OS&Y Gate Valve Page 11 XZ51X Flanged x Grooved Resilient OS&Y Gate Valve Page 12 Z85X Grooved Resilient

More information