TOGGLE DRIVEN BEAM PUNCHES AND PRESSES
|
|
- Derek Grant
- 6 years ago
- Views:
Transcription
1 TOGGLE DRIVEN BEAM PUNCHES AND PRESSES FOR PUNCHING EXTRA LARGE STRUCTURAL SHAPES AND MANUFACTURED PARTS MORE DIE SPACE 2 DEEPER THROAT LONGER STROKE 4 GREATER CAPACITY HIGHER PRESSURE G LESS POWER CONSUMED 7 LOWER MAl NTENANCE 8 LEAST FLOOR SPACE
2 No. IS TOGGLE BEAM PUNCH Photograph No Patent Applied For This highly improved type of Beam Punch has been designed to meet the increasing requirements of steel fabricating shops to handle a range of structural shapes and sections for both flange and web punching in one handling. The tool equipment can be furnished in several styles as found most suitable for.the work to be performed. The tools illustrated in photograph 1591 are used for odd hole Beam Punching, with a range from 6" H Beam to 36" wide flange Beam. Photographs 1682 and 1683 illustrate more of a straight production set up. Special tools covering a large variety of punching problems can be applied to these machines. The die space can also be modified if wider ram face is required. The Ram cannot tilt or twist, it has no overhang. The entire load can be concentrated for flange or web punching.
3 No. 14 TOGGLE BEAM PUNCH Punching Tools with double gag punching and die holders. Two diameters on each pitch line which saves time, money and re-handling as two diameter holes can be punched on same pitch line without loss of time to change tools. Control Levers for production or duplicate punching. This is also a time saver. Gag can be operated singly by detaching levers. NOTE-Clear Working Space. Clutch Control Levers on each side of Punch. Punching Tools with Double Gag Units NOTE-Small Fl oor Space. Do not overlook speed. This is the Fastest Large Punch Made. All top dies level, therefore plates can be punched with same tools.
4 No. 14 TOGGLE BEAM PUNCH Equipped With Spacing Table and Beam Handler Patent Appl ied for The above photograph illustrates the Toggle Beam Punch equipped with Spacing Table and Beam Handler or Turn Over which transfers the Beam from flange to web punching, requiring less than thirty seconds for the largest Beam. Same is controlled by the punch operator. See photographs 1678 and Rolls for Flange Punching adjustable from die level down to handle 36" Beams. Motor driven. The Beam Handler adjustable to handle all sizes. See Page 6 for Capacity and Speed.
5 No. 14 TOGGLE PUNCH Automatic Beam Handler transfering beam from flange to Web Punching Patent Applied for LARGE DIE SPACE. SMALL FLOOR SPACE
6 SPECIFICATIONS No. 13, 14, and 15 Structural Punches General Dimensions of Die Space Face of slide, right to left- Standard Maximum No , No. 14, 24 No Face of slide, front to back , 60 l..-oie space L -Stroke Throat Face of Table, front to back , 25 46, 48Vz" 60 48Th" 3, 34, 64 Face of Table, right to left- Standard , 22, 28, Maximum Lc. apac1ty T 34, 300T 38, 400T Shipping Weight ,000 lb. 57,000 lb. 76,000 lb. Motor Required-H. P Vz Spacing Table to Suit Requirements. CAPACITY Punching holes 1 Va" 4 holes 1/ 6 " 4 holes 1 Va" thru 1" thru "Va" thru 1 Va" Maximum Size of Material: Plates, width " 60" 60" 1-Beams- Girders " 36" 36" H-Columns, 195 pounds " 14" 14" Channels " 18" 18" Angles x8x1 Va" 8x8x1 Va" 8x8x1 Va" ] J
7 No. 16 TOGGLE PUNCH PRESS The No. 16 Toggle with large die space and suitable for punching and shearing tie plates, punching and straightening splice bars, also for general manufacturing press, punching and shearing articles. Drive is mounted inside of frame. J I t, ' o~ -.~.,. ' ~t ~ (;.t..'l,. -( J I
8 No. 16 TOGGLE PRESS Punching and Straightening High Carbon Ever Tight Splice Bars The Hydraulic head applies approximately 60 tons pressure on bar while punching, therefore, a perfectly straight forging and no re-handling.
9 No. 16 TOGGLE PUNCH Equipped with Hydro Pneumatic Accumulator The Hydro Pneumatic Accumulator supplies Hydraulic Pressure to die head and is furnished in various sizes to meet requirements. Equipped with magnetic or air clutch with convenient control station. Hand or foot operated.
10 No. 16 Series Heavy Duty Toggle Punch Press General Dimensions of Die Space No. 16 No. 16-A No. 16-B Face of slide, right to left " 53" 62" Face of slide, front to back " 26" 26" 'l-die space: 51 ide down f Stroke :' Standard.....)./.?!---. t;/~ -:, _.. ~~. I ) 20" $~ " 3" 20" 3" Maximum ' 5" 5" 5" Face of Table, front to back " 26" 26" Face of Table, right to left " 60" 66" Capa&~ty T 850T 1000T Strokes Depth of Throat " " " Weight ,000 lb. 82,000 lb. 88,000 lb. Motor Required-H. P The No. 16 Press has large die space and occupys a small amount of floor space with driving parts mounted inside the housing, operating at high speed. Roller Bearings in flywheel shaft. All bearings on slide lined with renewal bronze liners. The motor is mounted overhead. Air counterbalance to slide. Rigid construction! Minimum upkeep! The use of the Toggle to operate slide reduces the size and number of gears and the Horse Power of Motor, therefore a power saving.
11 -Well Known Users of Beatty Products Agricultural Implement Manufacturers ). I. Case Company Caterpi liar Tractor Company Deere & Company International Harvester Company Ohio Cultivator Company Oliver Farm Equipment Co. Van Brunt Manufacturing Company Car Builders- Armour & Company Canton Car Company General American Tank Car Company Greenville Steel Car Company Mather Stock Car Company Pacific Car & Foundry Company Pullman Car & Mfg. Company Pressed Steel Car Company Ryan Car Company Standard Steel Car Company Crane Builders- Bedford Foundry & Machine Co. Chain Belt Company Harnischfeger Corporation Whiting Corporation Miscellaneous- Bradford Corporation Cyclone Fence Company Ford Motor Company Pettibone-Mulliken Company Union Metal Products Company taylor-stiles & Company Stephens-Adamson Mfg. Company Boiler and Tank Manufacturers- Graver Corporation Stover Steel Tank Mfg. Company Railroad Shops- Chicago & Illinois Midland Railroad Chicago, Milwaukee, St. Paul & Pacific Railroad Chicago, Rock Island & Pacific Railroad Erie Railroad Great Northern Railroad Illinois Central Railroad Michigan Central Railroad Missouri-Kansas-Texas Railroad Northern Pacific Railroad Steel and Iron Works Acme Steel Company American Steel Foundries Austin Company Buffalo Steel Company A. M. Castle & Company Central States Bridge Co. Danville Structural Steel Company Dayton Structural Steel Company Hansell-Elcock Company Illinois Steel Company Inland Steel Company Interstate I ron & Steel Company Ingalls Iron Works Company LaSalle Steel Company Mahon Structural Steel Company 01 iver I ron & Steel Company Pacific Coast Steel Company Scully Steel & I ron Company St. Joseph Structural Steel Co. Western Pipe & Steel Company
40 Ton and 50 Ton Ironworker
40 Ton and 50 Ton Ironworker 40 TON THE SHOPMATE 4 Workstations Maximum capacity: 1" diameter in 1/2" plate 40 Ton and 50 Ton Ironworker Throat depth: 7" Stroke: 1" Work Height: 38-1/2" Open Station Throat
More information~11. H. J. WEBER & co W. CHICAGO AVENUE CHICAGO 51, ILLINOIS COLUMBUS MACHINE TOOLS - FABRICATING EQUIPMENT
~11 H. J. WEBER & co. 5722 W. CHICAGO AVENUE CHICAGO 51, ILLINOIS COLUMBUS 1-56 MACHINE TOOLS - FABRICATING EQUIPMENT c D PO ER PRESSES OPEN BACK INCLINABLE The SIXTY SERIES of C leveland Inclinable Open
More informationJANUARY - JUNE TON IRON WORKER $18,899 $13,999 $7,899 $1,049 $3,099 $170 $389 FOR MORE INFORMATION
JANUARY - JUNE 2018 65 TON IRON WORKER $18,899 SEE PAGE 66 GEARED HEAD BENCH LATHES CYCLONE DUST COLLECTOR 110 TON SHOP PRESS WITH PLC $7,899 $1,049 $13,999 WITH SEE PAGE 22 TRADESMAN VISE TRADEMARKED
More informationMADE IN THE USA SINCE product catalog
product catalog YOUR IS YOUR REPUTATION. That s why each and every day, you put it all out there for the world to judge. Never stopping and always looking forward to your next challenge. You know what
More informationMechanical equipment Pneumatic stamping-unit Hand-toggle-lever presses
Mechanical equipment Pneumatic stamping-unit Hand-toggle-lever presses Mechanical equipment ST 1092 ST 1292 page 7.03 ST 9041 page 7.04 ST 9062 page 7.05 ST 9067 page 7.05 ST 9072 page 7.06 ST 9075 page
More informationpow-er. presses, BALKO TooL & MACHINE ca.»»>>machinery<<<((<,6866 NO.. WESTERN AVE. AMussad
pow-er. presses, BALKO TooL & MACHINE ca.»»>>machinery
More informationSTRAIGHTSIDE PRESSES
STRAIGHTSIDE PRESSES Straightside presses are named because of the vertical columns or uprights on either side of the machine. The columns together with the bed and crown form a rigid box-like housing.
More informationJET FORMING. Brakes Shears Rolls Rotary and Hand Notcher Machines Presses
Brakes....................................... 111 Shears....................................... 114 Rolls........................................ 115 Rotary and Hand Notcher Machines.............. 117
More informationMachine elements. Pneumatic stamping unit. Toggle-lever presses
Machine elements Pneumatic stamping unit Toggle-lever presses Machine elements ST 1292 ST 1092 Page 7.03 ST 9041 Page 7.04 ST 9061/62 Page 7.05 ST 9067 Page 7.05 ST 9070/72 Page 7.06 ST 9075 Page 7.07
More informationCONTENTS BUILD YOUR LEGEND YOUR WORK IS YOUR REPUTATION AND SO DO WE. BECAUSE WE ARE NEVER CONTENT WITH THE STATUS QUO.
YOUR WORK IS YOUR REPUTATION That s why each and every day, you put it all out there for the world to judge. Never stopping and always looking forward to your next challenge. You know what it means to
More informationCONTENTS ONE YEAR LIMITED WARRANTY
CONTENTS SIDE PUMP BOTTLE JACKS 3 AIR ACTUATED BOTTLE JACKS 4 FAST LIFT SERVICE JACKS 5 SERVICE JACK 5 LOW PROFILE FAST LIFT SERVICE JACK 6 3 TON FAST LIFT SERVICE JACK AND 3 TON JACK STANDS 6 COMBO AIR
More informationHoists Polipastos Hebezeuge Palans
Hoists Polipastos Hebezeuge Palans By Detroit Hoist PAGE 2 Better Cranes Begin with Detroit Hoist At the forefront of hoist technology - US made since 1905 For almost a century Detroit Hoist has designed
More informationCITY OF ROCK ISLAND S P E C I F I C A T I O N S
CITY OF ROCK ISLAND S P E C I F I C A T I O N S It is the intent of the City of Rock Island to receive bids on fourteen (14) snow plows. The proposed plows will be used by the Public Works Departments
More informationHYDRAULIC. IRONWORKERS SW-Series
HYDRAULIC IRONWORKERS SW-Series IRONWORKERS Every Machine Has 5-Station Versatility Built In Station Baileigh Industrial offers the highest quality Ironworkers on the market today. Our 50 ton, 62 ton,
More informationPNEUMATIC PRESSES. pneumatic presses DESCRIPTION FEATURES AND OPTIONS
3 DESCRIPTION Air-Mite has been manufacturing since 1952. We are continuously improving the durable, time-tested design of our presses PRESS SELECTION that they exert. From the smallest DPS4 model, which
More informationReversing Switch for Ram Adjustment Motor. Depth of Throat. and Handle. Rolled Steel Welded Gears. Multiple "V" Belt Drive
Bronze Bushings in Main and Intermediate Shaft Bearings One-Piece Forged Alloy Eccentric Shafts Fully Enclosed Adjustment Gears Automatic Force Feed Oiling System SERIES D ~ Reversing Switch for Ram Adjustment
More informationHoists & Rigging Products for Construction Projects
Manual Hoists Have a special application? Our full line of material handling products allows us to create complete solutions rather than just offering single products. Now you have one point of contact
More informationBULLETIN 507. Mechanical Forging Presses
BULLETIN 507 Mechanical Forging Presses...-. ~ " The Erie Foundry Company designs and manufactu res quality machine tools that are used around the world. Erie presses have been built to stamp, cut, blank,
More informationAtlas BUYER S CHOICE
HO MASTER 40 AAR Postwar Box Car www.atlasrr.com/hofreight/ho40postwarbc1.htm Spurred by the postwar business boom and in an effort to replace worn out equipment, North American railroads built large numbers
More informationMINSTER. P2 Series Presses PIECE-MAKER. Group Company TONS CAPACITY BULLETIN 130C
A Group Company BULLETIN 130C MINSTER P2 PIECE-MAKER 60-200 TONS CAPACITY HIGH PERFORMANCE COMBINED WITH DURABILITY RELIABILITY AND SERVICEABILITY IN STRAIGHT SIDE PRECISION PRESSES P2 PIECE-MAKER INTRO
More informationDistrict Sales Offices
Crane Rail Systems sales offices fabrication & distribution facilities headquarters District Sales Offices California 32970 Alvarado Niles Road #736 Union City, CA 94587 P: 510.471.9840 / F: 510.471.9847
More informationBENDING ROLLS FAST -- ACCURATE -- VERSATILE MACHINE TOOL DIVISION
v E R Cj~ -3 T c A L BENDNG ROLLS FAST -- ACCURATE -- VERSATLE Commercially accurate circles, segments and spiral bending are turned out at high production rates by these compact, efficient machines. Occupying
More informationDouble Column Vertical Machining Centers
Double Column Vertical Machining Centers Double Column Vertical Machining Centers www.toyoda.com Your local distributor is: Corporate Headquarters 316 West University Drive Arlington Heights, IL 60004
More informationIRONWORKERS & PUNCHING MACHINES
HYDRAULIC IRONWORKERS & PUNCHING MACHINES Multi-Function Excellent Quality Economical Investment ISO 9001 INTRODUCTION With a highly dedicated team, Sunrise Fluid Power Inc. has been specializing in the
More informationHydraulic clamping elements
Hydraulic clamping elements hydraulic 3 Contents Product group 3 Hollow piston cylinder single-acting 3.1403 3.2130 Sliding clamp single-acting compact classic 3.2202 3.2204 Angular clamping element single
More informationCOMPLETE LATE MODEL FABRICATING FACILITY AUCTION CONDUCTED BY:
PUBLIC AUCTION WEENING BROTHERS MANUFACTURING INC. MARK YOUR CALENDARS! Tuesday, June 12, 2018 10:30 A.M. EDT 33475 Hwy 88, RR #1, Bradford, Ontario, L3Z 2 INSPECTION: Monday, June 11 from 9:00 A.M. to
More informationToll-free:
Toll-free: 1.800.362.4601 CRANES CRANE SERVICE WIRE ROPE ENGINEERED PRODUCTS HARDWARE SLINGS TRAINING CAPABILITIES BROCHURE >> www.progressivecrane.com Cranes: Progressive Crane is a leading manufacturer
More informationSpartec CONVEYORS DESIGN MANUFACTURE INSTALLATION CONVEYORS
DESIGN MANUFACTURE INSTALLATION PARTS SCRAP PACKAGE BULK HANDLING LOW PROFILE DIE-VEYORS 2 Frame Heavy Duty BELT WIDTH + 1 1/2" 3/4" BELT WIDTH 3/4" 2" 1" BELT WIDTH + 3/4" SECTION VIEW WIDTHS: 2 Thru
More informationSimpLok Shaft Holders. Holders Unwind and rewind modules Skew adjustment Lateral adjustment Skew and lateral adjustment Web guided modules
SimpLok Shaft Holders Holders Unwind and rewind modules Skew adjustment Lateral adjustment Skew and lateral adjustment Web guided modules SimpLok Shaft Holders SimpLok shaft holders are the perfect answer
More informationAir Carbon Arc Gouging Torches & Equipment; Slice Exothermic Cutting Systems. Gouging & Cutting Products & Accessories
Air Carbon Arc Gouging Torches & Equipment; Slice Exothermic Cutting Systems Gouging & Cutting Products & Accessories Gouging & Cutting Products & Accessories EXTREME Air Carbon Arc Gouging Torches Angle-Arc
More informationShearing, bending, and rolling capabilities are available along with fabricating from hand drawn sketches to engineered drawings.
Tazgo Machine Inc. is a full service stocking warehouse. Items we stock include carbon, aluminum & stainless steel shapes, angles, beams, flats, hex bar, bar grating, squares, CR rounds in 1018,1045 &
More informationSPECIALTY PRODUCTS INDEX... A-1 MTO SPECIALTY PRODUCTS... A-2. Bronze Bushed... A-3. Ball Bearing... A-4. Ball Bearing - Non-Metallic...
Index SECTION A SPECIALTY SPECIALTY PRODUCTS PRODUCT PAGE INDEX................................................................................... A-1 MTO SPECIALTY PRODUCTS................................................................
More informationBucket Elevators & Conveyors
Bucket Elevators & Conveyors Bucket Elevator Heads GSI's bucket elevators & conveyors are engineered to perform and built tough to provide years of reliable service. Whether your business is industrial
More informationfor CONSTRUCTION PROJECTS HOISTS & RIGGING PRODUCTS FOR CONSTRUCTION Power Plants Commercial Construction Wind Energy Bridges & Highways
A Complete Line of Products & Solutions for CONSTRUCTION PROJECTS HOISTS & RIGGING CONSTRUCTION Power Plants Commercial Construction Wind Energy Bridges & Highways TOUGH. RELIABLE. STRONG. Keeping Projects
More informationPUNCH RANGE HYDRAULIC PUNCHING MACHINE
PUNCH RANGE HYDRAULIC PUNCHING MACHINE PUNCH RANGE Punch station-applications (optional equipment) Minimum deform stripper assembly Minimum deform stripper assembly to give minimum deformation while punching
More informationw w w. m a r v e l s a w s. c o m
Quality Machines by Vertical Band Saws Series 8 Mark III Miter cuts up to 60 with optional power column tilt. Column adjustable from 90 to 3 canted. Capacity: 18 X 22 (457mm x 560mm) at 45 18 x 14.5 R,
More informationLength. Area. Volume. OH USA, p
Conversion of Units 1 Length 1 millimeter = 0.0394 inch 1 centimeter = 0.394 inch 1 meter = 39.4 inches 1 meter = 3.2808 feet 1 kilometer = 0.62137 mile 1 inch = 25.4 millimeters 1 inch = 2.54 centimeters
More informationTFX2 80 TFX TFX2 Series Augers
TFX2 80 TFX2 100 TFX2 Series Augers Our Best Farm Proven Features Main Tubes Main tube connections are welded and flanges are bolted togther for maximum strength. Aircraft cable trussing on longer units
More informationDirect contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI.
Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as
More informationH. J. WEBER Be CO W. CHICAGO AVENUE CHICAGO 51, ILLINOIS. COLUMBUS
H. J. WEBER Be CO. 5722 W. CHICAGO AVENUE CHICAGO 51, ILLINOIS. COLUMBUS 1-5644 MACHINE TOOLS - FABRICATING EQUIPMENT DOUBLE CRANK POWER PRESSES INDEX POWER P STRAIGH SIDED DOUBLE CRANK SD2-60 Pa9e 3.
More informationFabrication Series Hydraulic Press Brake 14' x 242 Tons
Box 20, Grp. 200, RR2, 390 Eagle Drive, Winnipeg, MB R3C 2E6 Canada Toll Free 800-665-8089 Ph: 204-779-7791 Fax: 204-779-7796 Email: sales@empire-machinery.com December 18, 2017 Technical Specifications:
More informationCone 900. C900 Standard/Metric. Specification. Omron/CoastOne software
Built in Finland, CoastOne press brakes are designed to surpass the exacting requirements of today s high-tech fab shops. Every CoastOne comes equipped with the highest quality linear guides and fast,
More informationSTANDARD FEATURES: Closed 9-1/4" Work Stations From Floor 42" Height w/o Die Block Hydraulics: Optional Lengths Available Weight (NET) lbs 2600
IRONWORKERS The Piranha Model P-50 features Automatic Urethane Hold Downs on the Punch Stripper and Bar, Plate and Angle Shear. This assures precise cuts and longer punch and blade life. Complete Punching
More informationThe AFF Total Value Commitment
The AFF Total Value Commitment Since 1963, American Forge and Foundry has provided a full selection of Forge-Tough hydraulic lifting products, lubrication tools, and general shop equipment. Serving Repair
More informationMULTI HYDRAULIC STEELWORKER
MULTI HYDRAULIC STEELWORKER MULTI 3 2 1 4 5 Hydraulic steelworker The Kingsland Multi range of 60 up to 175 ton machines are in the Kingsland tradition of well engineered, robust steelworkers, built for
More informationINTERLOCKS FOR TRANSFER CRANES
INTERLOCK FOR TRANFER CRANE The productivity of many crane systems can be greatly increased by including transfer cranes in the system. Cleveland Tramrail transfer cranes permit trolleys to be transferred
More informationProduct Description. Lionel Locomotives compatible with LCS SensorTrack
Lionel Locomotives compatible with LCS SensorTrack Listed below are all the previously produced Lionel Legacy locomotives which are equipped with the IR transmitter. These are 100% compatible with the
More informationCelebrating 50 Years of Excellence. 50YEARS PROFESSIONAL LIFTING EQUIPMENT.
Celebrating 50 Years of Excellence. 1964 PROFESSIONAL LIFTING EQUIPMENT 50YEARS www.norcoindustries.com America s fastest and most durable AIR/HYDRAULIC AXLE JACKS 1 1964 PROFESSIONAL LIFTING EQUIPMENT
More informationDistributed by Tri-State Equipment Company Inc
Distributed by Tri-State Equipment Company Inc. sales@tsoverheadcrane.com 314-869-7200 www.tsoverheadcrane.com Harrington Manual hoist products CB Hand Chain Hoist 1 2 through 100 Ton capacity Harrington
More informationRousselle Single Point Gap Frame (Cast Iron)
Single Point Gap Frame 15 to 110 Tons Rousselle Single Point Gap Frame (Cast Iron) Standard Features Cast Frame Air Clutch and Shoe Brake Crankshaft Motion (40 Ton and Up) Eccentric Shaft Motion (15 and
More informationAccessories Catalogue
Accessories Catalogue GEKA ACCESSORIES Since 1919, GEKA Group has been manufacturing Ironworkers for angle work, flats and profiles - for black iron, metal workshops, metal constructions, telecommunication
More informationrecognized as the best in the industry for over 115 years. Each component is designed with greater innovation and manufactured with higher
0-0_q_K //0 : PM Page C R A N E C O M P O N E N T S TM TM THERE S A CRANE SOURCE COMPONENT FOR EVERY JOB. CraneSource crane bridge components have been recognized as the best in the industry for over years.
More informationMODERN TECHNOLOGY IN PUNCHING AND SHEARING
MODERN TECHNOLOGY IN PUNCHING AND SHEARING SOLUTION The GEKA HYDRACROP range of hydraulic steelworkers have been designed by highly experienced engineers with the support of powerful CAD equipment, culminating
More informationDirect contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI.
Direct contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as
More informationJACKS & LIFTS JACKS & LIFTS BOTTLE JACKS JACK STANDS JACKS & LIFTS JACK PACKS JACKS & LIFTS UNDER HOIST STANDS. Bottle Jacks - Stands
BOTTLE JACKS TEQ Correct Professional 12 Ton Short Professional Bottle Jack EQP 3113 JACK STANDS Low Height: 12 3/16" Raised Height: 18 7/8" TEQ Correct Professional 3 Ton Ratcheting Professional Series
More informationCatalogue of Black-line scale drawings January, 2014
Catalogue of Black-line scale drawings January, 2014 1 Although I am a product designer for medical devices and consumer products, my first love is Industrial Archeology and the re-creation of objects
More informationHarrington Beam Accessory Kits. Options and Accessories: Consult Factory. Compliance
Harrington Beam Accessory Kits Provides the convenience of pre-fabricated bracing and bridge beam accessories. For use with any Harrington end truck specify end truck model when ordering. Kit includes:
More informationAmada Rg3512 Ld Press Brake Manual
Amada Rg3512 Ld Press Brake Manual If searching for a book Amada rg3512 ld press brake manual in pdf form, then you have come on to the right site. We furnish utter version of this ebook in epub, DjVu,
More informationADJUSTABLE AIR PRESS
ADJUSTABLE AIR PRESS MODELS 12-A, 28-A, 50-A INSTALLATION, OPERATING, and MAINTENANCE INSTRUCTIONS Black & Webster Assembly Equipment Division 545 Hupp Ave. P.O. Box 831 Jackson, Michigan 49204 Phone:
More informationPRESS BRAKES PRESS BRAKE DIES STRAIGHT-SIDE-TYPE PRESS BRAK POWER BENDING BRAKES HAND OPERATED BENDING BRAKES SPECIAL METAL-FORMING MAC ~ INES
PRESS BRAKES PRESS BRAKE DIES STRAIGHT-SIDE-TYPE PRESS BRAK POWER BENDING BRAKES HAND OPERATED BENDING BRAKES SPECIAL METAL-FORMING MAC ~ INES A Tradition of Quality and Value since 1899 DREIS & KRB MP
More informationWILTON SAWING. Horizontal Bandsaw s Vertical Bandsaws Cold Saws Cold Saw Blades Accessories... 32
Horizontal Bandsaw s........................... 18 Vertical Bandsaws.............................. 24 Cold Saws.................................... 27 Cold Saw Blades............................... 31
More informationTHE BEST MOVES IN THE WORLD
THE BEST MOVES IN THE WORLD UNDERHUNG & TOP RUNNING CRANES STACKER CRANE SYSTEMS MONORAILS `SPECIALIZED AVIATION MAINTENANCE CRANES SPECIALIZED LAUNDRY & OVERHEAD MATERIALS HANDLING THE RIGHT MOVE TC/American
More informationCOMPANY HISTORY Di-Acro Metal Fabrication Equipment
COMPANY HISTORY Di-Acro Metal Fabrication Equipment For more than sixty years, Di-Acro Inc. has served the metalworking industry producing metal fabricating equipment. We ve maintained the same traditional
More informationMANUAL HOISTING TAKE THE WEIGHT OUT OF HEAVY DUTY LIFTING
MANUAL HOISTING TAKE THE WEIGHT OUT OF HEAVY DUTY LIFTING CARE & SAFETY INSTRUCTIONS 114 CX & M3 SERIES CHAIN BLOCKS 115-117 C SERIES CHAIN BLOCKS 118 MINI II CHAIN BLOCKS 118 LX & L5 SERIES CHAIN BLOCKS
More informationCHAIN & HOOKS. Proof Coil Chain Grade 28. Transport Chain Grade 70
Proof Coil Chain Grade 28 Proof coil chain is suitable for use as towing chain, logging,fencing, trailer safety chain, boat anchors, security barriers or other general purposes where chain of high tensile
More informationBASANT MECHANICAL WORKS (REGD.) MANUFACTURERS & EXPORTERS OF HIGH CLASS POWER PRESSES AND KNUCKLE JOINT PRESSES.
7-721, Basant Road, Industrial Area-B, Ludhiana - 13 (INDIA) 91-97802-00007, 9315-11111 info@basantgroup.com www.basantgroup.com BASANT MECHANICAL WORKS (REGD.) MANUFACTURERS & EXPORTERS OF HIGH CLASS
More informationUpdate of the Midwest Regional Rail Initiative. Tim Hoeffner Michigan Department of Transportation Director, Office of Rail Lansing, MI
Update of the Midwest Regional Rail Initiative Tim Hoeffner Michigan Department of Transportation Director, Office of Rail Lansing, MI Key Presentation Take-Aways Status of Midwest Regional Rail Initiative
More informationCHANDLER LOW PROFILE
CHANDLER LOW PROFILE ORCHARD AND GROVE PULL-TYPE FERTILIZER AND LIME SPREADER (Unit Shown W/PTO Drive Spinners) Hopper Specifications 3-Ton Capacity (Fertilizer) 5-Ton Capacity (Lime) Available In: 304
More informationBUILT WITH INTEGRITY
WITH INTEGRITY Let us share our wealth of knowledge accumulated over three decades. We have equipped the material handling industry across North America with some of the most resilient cranes and crane
More informationMaxi-Stamper. 200 to 1,000 Tons STAMPING OUT DOWNTIME
TM Maxi-Stamper 200 to 1,000 Tons STAMPING OUT DOWNTIME Stand ard Features Steel Fabricated Construction Drive Capacity Rated 1/2 Above Bottom of Stroke Self-Diagnostic Solid State Controller Moveable
More informationPallet Forks Hydraulically Shifting and Tines with Continuous Spindle Adjustment
Pallet Forks Hydraulically Shifting and Tines with Continuous Spindle djustment The efficient pallet fork with a hydraulically compensating centre of gravity can easily be adapted to different loads with
More informationElJay Rollercone Classic and ElJay Rollercone II 36, 45, 54, 60, 66 ELJAY ROLLERCONE
ElJay Rollercone Classic and ElJay Rollercone II 36, 45, 54, 60, 66 ELJAY ROLLERCONE ELJAY ROLLERCONE OFTEN IMITATED, NEVER EQUALED INCREASED OUTPUT FROM ADVANCED ENGINEERING The TEREX Cedarapids ElJay
More informationKnife Gate & Butterfly Valves Data Sheets
Knife Gate & Butterfly Valves Data Sheets Series 80-TP Series 80-TP/XL Series 80-BA Series 80-SS Series 80-SSRS Series 80-DI Series 150 Series 120 Butterfly Valves Series TM-3 & TM-4 Butterfly Valves www.townley.net
More informationAdding performance to the industry. Widest Range of Machines installed with proven performance AN ISO 9001:2000 CERTIFIED COMPANY.
Adding performance to the industry We at Energy Mission believe to deliver high quality products at competitive price supported by best service support. To achieve this mission, we have developed inhouse
More information/2017. Hollow piston cylinder, single-acting spring clamping hydraulic unclamping
, single-acting spring clamping hydraulic unclamping Applications: un-pressurized long-term clamping of dies or fixtures on press beds and rams when the space available is limited T-bolt Spring clamping
More informationORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and C-to-C dimension. C - C LOAD lb.
Fig. 2110 www.pipingtech.com/fig2110 Sway Strut with 4 of Adjustment Engineered spring supports option 1 option 2 ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and
More informationPROFESSIONAL LIFTING EQUIPMENT DEPENDABLE PRODUCTS 50YEARS QUALITY SAFETY PERFORMANCE. Over
PROFESSIONAL LIFTING EQUIPMENT DEPENDABLE PRODUCTS 1964 QUALITY SAFETY PERFORMANCE PROFESSIONAL LIFTING EQUIPMENT Over 50YEARS WHY SHOULD YOU CHOOSE NORCO? PROFESSIONAL LIFTING EQUIPMENT Exceptional Customer
More informationELECTRONIC OVERHEAD TRAVELLING CRANE DIMENSIONS & LOAD DATA
ELECTRONIC OVERHEAD TRAVELLING CRANE DIMENSIONS & LOAD DATA FOR ESTIMATING PURPOSES ONLY CONTENTS TOP RUNNING SINGLE GIRDER CRANES 2, 3 & 5 Ton 7.5 & 10 Ton PAGE 2-5 TOP RUNNING DOUBLE GIRDER CRANES 5,
More informationSHEARING & PRESS BRAKE - KAWA HYDRAULIC PRESS BRAKE
SHEARING & PRESS AKE - KAWA HYDRAULIC PRESS AKE Frame : The frame is of heavy duty design and hot rolled welded steer plate construction. The shearing table is Integral wi e basic machine frame to ensure
More informationB.I. Brooks and Sons Inc. Overhead Conveyor
B.I. Brooks and Sons Inc. Overhead Conveyor 3 and 4 I-Beam Conveyor Components X348 and X458 Track, Chain, and Trolleys Roller Turns and Traction Wheel Turns Drive Units Chain Take Ups in business since
More informationIf You Can Produce It, We Can Move It. Custom engineered products for safe, reliable and efficient material handling.
MATERIAL HANDLING AND FABRICATED PRODUCTS If You Can Produce It, We Can Move It. Custom engineered products for safe, reliable and efficient material handling. Avon Engineering is recognized as a leader
More informationDIVISION 14 CONVEYING EQUIPMENT
DIVISION 14 CONVEYING EQUIPMENT Page 1 of 4 Part 1 General 1.1 SCOPE OF WORK.1 Supply and install one (1) complete overhead (push trolley electric chain hoist) under running monorail crane systems as mentioned
More informationWELDOR CNC MACHINES. We invite your kind attention to your interest of below machines and discussion for the same.
WELDOR CNC MACHINES Mail: - weldorcncmachines@gmail.com Mobile Number: - +91 83061 84061 / +91 92277 55528 Web1:- www.weldorcncmachines.com Web2:- www.weldorpunchpress.com Address: - Survey No.240, Behind
More informationHOISTS RATCHET LEVER HOISTS
Yale HOISTS RATCHET LEVER HOISTS Yale PE & RS Ratchet Lever Hoist / to ton capacities Link chain models Light and portable Weatherized load brake Requires less handle pull to lift full load Efficient Yale
More informationManufactured in the U.S.A. HVAC Rollforming and Sheet Metal Equipment
Manufactured in the U.S.A. HVAC Rollforming and Sheet Metal Equipment Where superior duct work begins. The Vicon line of HVAC Rollforming and Sheet Metal Equipment is the industry proven solution for all
More informationValve Lapping Tool Attachment. Valve / Valve Spring Tools / Jacks / Axle Stands. 27-piece Valve Seat Cutter Set, mm
Valve Lapping Tool Attachment - facilitates the insertion of valves - automatic change in direction - for use with fine grinding paste - with 8 mm shank - working speed min. 1000 rpm, max. 1250 rpm - 2
More informationLaboratory pellet mill
The pellet MILL FOR the Professionals Laboratory pellet mill - 6 pole motor 18,5 kw max. - Conditioner motor 0,75 kw - Feeder speed can be used with VFD or hydraulic gear drive (0,37 kw) - Die I.D. 200
More informationIMPACT HAMMER MODEL Z-2 & Z-6 PARTS AND OPERATING MANUAL
IMPACT HAMMER MODEL Z-2 & Z-6 PARTS AND OPERATING MANUAL Black & Webster Products Division 545 Hupp Ave. P.O. Box 831, Jackson, Michigan 49204 Phone: (517-787-9444 Fax: (517) 787-7585 Email: info@airhydraulics.com
More informationRiver Falls FFA Alumni. July 14th 2018 Tractor Pull Rules
River Falls FFA Alumni July 14th 2018 Tractor Pull Rules Tractor General Rules 1. Be a Professional. Must have tractor registered before class starts. No exceptions made. Can call ahead of time to get
More informationBOLT PLANT (Automatic)
BOLT PLANT (Automatic) (a) Automatic High Speed Double Stroke Cold Heading Machines (b) Automatic Bolt Head Trimming and Shank Reducing Machines (c) Automatic Thread Rolling Machines (High Speed) DOUBLE
More informationGARAGE EQUIPMENT NATIONWIDE SALES SERVICE INSTALLATION AUTOQUIP. Garage & Tyre Equipment CORK. Phone: Website:
GARAGE EQUIPMENT NATIONWIDE SALES SERVICE INSTALLATION AUTOQUIP Garage & Tyre Equipment CORK Two-Post Lifts PA-6140A Manual Lock Release PA-6140D Electric Lock Release P Our lifts are fitted with a low
More informationServices. Rental Equipment RENTAL DIVISION PRODUCT LINES. LOAD RESTRAINTS Load Binders (Lever & Ratchet) Truck Tie-down Assemblies Boomer Chains
RENTAL DIVISION PRODUCT LINES In a continuing effort to give the customer the opportunity to get an assortment of equipment, services and products from one supplier, our rental division was established
More informationGLOBAL KINGTM &WORLD SERIESTM
GLOBAL KINGTM &WORLD SERIESTM ELECTRIC WIRE ROPE HOISTS COl UMBUS McKINNON CORPORATION -48 QUICK SHIP PROGRAM IS EVEN IBLE Since its launch, the Flex-48 Quick Ship Program has proven to be a reliable and
More informationStructure of Wind Supply Chain Onshore to Offshore. Ed Weston Director, GLWN Copyright 2012 GLWN A WIRE-Net Initiative
Structure of Wind Supply Chain Onshore to Offshore Ed Weston Director, GLWN eweston@glwn.org FIND Connections Company name WIND Classification Component Families Radius Search Active Suppliers Almost 1600
More informationIndustrial Boiler MACT Experience
(includes current January Final Reconsidered Rule, which replaced the March Rule) (Energy Assessment) Orion, Michigan (Energy Assessment) Wentzville, Missouri (Energy Assessment) Fairfax, Kansas (Energy
More informationA PROVEN ...WITH HUMBLE BEGINNINGS ...AND A VERY BRIGHT FUTURE U.S. COMPANY. First C-Frame. First Four Column. First Shear
PRESS BRAKES A PROVEN U.S. COMPANY...WITH HUMBLE BEGINNINGS First C-Frame First Shear First Four Column...AND A VERY BRIGHT FUTURE POWERFUL, PRECISION MACHINES MADE IN THE USA / 02 MODEL AB PRESS BRAKES
More informationCONTACT INFORMATION. Charleston, WV Location. 901 Brooks Street Charleston, WV Telephone: (304)
CONTACT INFORMATION Poca, WV Location (River Plant) 300 Wright Glass Addition Road PO Box 1029 Poca, WV 25159 Telephone: (304) 755-5638 Sales Fax: (304) 755-8611 Accounting Fax: (304) 755-8589 Charleston,
More information& SK ELECTRIC WIRE ROPE HOISTS. COLUMBUS McKINNON CORPORATION
YK & SK ELECTRIC WIRE ROPE HOISTS COLUMBUS McKINNON CORPORATION YK & SK ELECTRIC WIRE ROPE HOISTS When you need quality and performance in a wire rope hoist, turn to the Yale YK and Shaw-Box SK hoists
More information100 YEARS C H I C A G O, M I L W A U K E E, S T. P A U L A N D P A C I F I C R A I L R O A D C O M P A N Y
100YEARS C H I C A G O, M I L W A U K E E, S T. PA U L A N D PACIFIC RAILROAD C O M PA N Y 100 YEARS OF LOCOMOTIVE PROGRESS On a Fall day in the year 1850, the Milwaukee Road's first locomotive, coupled
More informationRW 1200 ROCK WINDROWER. Table of Contents
RITE WAY MFG. CO. LTD. P.O. Box 328 Imperial, Saskatchewan Canada, S0G 2J0 Ph: (306) 963-2180 Fax: (306) 963-2660 Web Site: www.ritewaymfg.com E-mail: info@ritewaymfg.com RW 1200 ROCK WINDROWER Table of
More information