Automotive Lifting Equipment
|
|
- Kathlyn Annabel Peters
- 1 years ago
- Views:
Transcription
1 Automotive Lifting Equipment Vehicle Hoists A vehicle hoist / lift is a necessary tool in any automotive repair shop. There are several common types of auto hoists used in repair shops: above ground two post lifts above ground four post lifts Other variations are not as common but include side lifts and scissor lifts. In ground lifts can be further divided into low pressure lifts and high pressure lifts. These terms describe the fluid pressure levels used to extend the lift. Identified Risks and Hazards Falling objects tools, vehicle components etc. Trapping hazards finger crushing in machinery Crushing hazards hand injuries Entanglement hazards clothing and body parts caught in machinery Slip, Trip hazards liquids and equipment on floors Improperly maintained or adjusted hydraulic parts can cause serious injury. Always use caution when working on a hydraulic system. Even when the system is shut down, hydraulic oil can still be under pressure. Copyright 2010 OnGuard Safety Training PTY LTD 1
2 If the controls for more than one lift are in one location, they should be numbered or colourcoded to ensure operators know which control operates each individual lift. Pre-operational Safety Ensure you understand the information provided in the automotive lift s manual and that the operating and maintenance instructions are permanently located and clearly visible. The equipment must be used in accordance with manufacturer s instructions. Inspect the automotive lift for any disrepair. In addition, assure that the hydraulic oil levels are at the correct amount and chains, cables, drums are not damaged, corrosive or worn. Familiarise yourself with and check all machine operations and controls. Check the capacity of the hoist compared to the weight of the vehicle. If vehicle is too heavy, do not proceed. Check all safety devices are in good condition. Ensure support arms are capable of being locked in position. Ensure rubber pads are in good condition on all load points. Ensure that you are wearing the appropriate personal protective equipment including your hard hat, safety glasses, gloves, boots and ear plugs if the lift is excessively noisy. Ensure the area is clean and clear of grease, oil, and objects that may be a slip/trip hazard. Faulty equipment must not be used. Immediately report any suspect equipment. If the lifting device does not conform then notify your supervisor immediately. Operating Safety Precautions Never attempt to lift a load that exceeds the rated capacity of the automotive lift. Centre vehicle on hoist, ensuring that the weight is evenly distributed to the front and rear. Never raise a vehicle with a person inside. Identify the correct jacking points and place the lifting pads under the vehicle at the front & rear on the jacking points, ensuring contact. Raise the vehicle about one foot off the floor. Check the stability by pushing or shaking gently. Do not try to stabilize a vehicle when it is in the air. Lower it immediately. Ensure that the automotive lift locking devices are in place. Never work under a vehicle that does not have the load locking devices in place. Engage manual lock. Copyright 2010 OnGuard Safety Training PTY LTD 2
3 Only one person shall operate the hoist at a time. Do not leave the controls whilst the lift is in motion. Do not raise only one end of the vehicle with the lift. Ensure the area around the automotive lift is cleared of any rubbish or spilt fluids. Ensure hoist area is clear of people and equipment before operating. Never leave the hoist running unattended. Do not work on vehicle while it is being raised Do not stand directly in front of the vehicle Do not rock a vehicle on a lift. Do not lower the lift to rest on supporting jacks. Extend the height of the jacks to support the weight of the vehicle. Do not use wooden blocks or homemade devices in place of proper lifting adaptors. Do not rely on hoisting equipment. Support equipment on blocks or stands. Do not lower the vehicle until all people, tools, and materials are clear from under lift. At the completion of work lower the vehicle hoist and ensure to remove all tools and obstructions from beneath the vehicle. Daily Maintenance Lift arms check for cracks and breaks in welds or castings lubricate swivel points Chains and cables Check chain and cables for unusual stretch or wear Lubricate chains and cables Inspect connections for corrosion or fatigue Check sockets and pulleys for wear Examine coating and sheath on cables If there is slack sensors ensure they are working Operating Procedures Know the load limits of the lift and adaptors. Do not overload. The rated capacity is displayed on the manufacturer's name plate. Copyright 2010 OnGuard Safety Training PTY LTD 3
4 Position the vehicle so that the centre of gravity is in accordance with manufacturers' recommendations. Put the transmission in neutral position, turn off ignition, close all car doors, and check for overhead obstructions such as radio aerials. Place adaptors or pads in the proper position under the recommended contact points. Check that the automatic chock devices on drive-on or runway lifts are in position before raising a vehicle. Ensure that permanent blocks are sufficient to stop a vehicle. As the lift is raised, observe the automatic chocks at the drive-on end of the lift runners. Raise the lift until the vehicle's wheels are just off the floor (about 30 cm or 1 ft). Then check again to ensure that contact pads and any adaptors are set accurately and that loads are not being placed on parts of the vehicle which might be damaged. Lower the vehicle and readjust the lift before continuing further if the contact with the vehicle is not even or if it looks as if the vehicle may slip. Do not bang or move the lift quickly at the top. Raise it slowly for the last 45 cm. Banging the lift will stretch the seal bolts and allow oil to leak. Lock the lift with the mechanical locking device or use appropriate jack stands. Be aware of conditions that could cause the vehicle's centre of gravity to shift and cause the vehicle to fall. For example, before lifting a vehicle, remove a load or cargo if it can shift unexpectedly, or follow the manufacturer's recommendations for removing heavy components like engines or axles and universals. In addition, the removal or installation of parts may cause the centre of gravity to shift and the vehicle to become unstable. Watch for low obstructions when walking under a supported vehicle. Wear suitable personal protective equipment (PPE) when working under raised vehicles; e.g., goggles or face protection for protection from leaking fluids, rust, dust, etc. or a hard hat to prevent injuries from bumps or falling objects. Check overhead clearances before lifting. Watch for antennas, vehicle signs and attachments. Close the vehicle doors, hood, and trunk, and make sure no one is inside before raising the vehicle. Keep people at least 2 m away from the vehicle about to be raised. Carry out a daily safety check of all components before using the lift. Check that no tools, equipment, jacks or other obstructions are under the lift. Ensure that everyone is standing clear of the lift before it is lowered. Copyright 2010 OnGuard Safety Training PTY LTD 4
5 Lower the vehicle slowly and smoothly and allow the lift to go as low as possible. Adjust lift arms or other supports, or remove chocks, as needed, so that the vehicle can be moved without bumping into any parts of the lift when the vehicle is driven out of the garage. Other lifting devices Engine Lift / Crane The main use of these lifting devices is removing/replacing engines and transmissions in cars and light commercials. Steel wheels to easily move around your workshop. Dismantles to transport in most car boots. Has steel casters for easy moving. Engine Stand A portable hand operated device for supporting car engines during repairs or rebuilding with the added advantage of easily rotating the engine for easy access to any particular area. It allows motor to be turned 360 degrees. Copyright 2010 OnGuard Safety Training PTY LTD 5
6 Hydraulic Jack These jacks are used for lifting, raising and jacking machinery, cars, trucks and buildings. They are light to carry and easy to use. There are a wide range of capacities and sizes. Trolley / Floor Jack These jacks are used for lifting, raising and jacking cars and trucks. They are easily moved as they are mounted on wheels. The rear set of wheels are on swivel mounts, allowing easy manoeuvrability. Chain Block A hand operated block & tackle lifting apparatus with workshop, rural & engineering applications. Popular tasks include engine and machinery hoisting. Copyright 2010 OnGuard Safety Training PTY LTD 6
7 Car Stands A portable hand positioned device for supporting car chassis during repairs or rebuilding. Copyright 2010 OnGuard Safety Training PTY LTD 7
3-TONNE GARAGE JACK OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: CTJ3000GB PART NO: ORIGINAL INSTRUCTIONS
3-TONNE GARAGE JACK MODEL NO: CTJ3000GB PART NO: 7623032 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1216 2 INTRODUCTION Thank you for purchasing this CLARKE Garage Jack. Before attempting
GENERAL HOUSEKEEPING. 1. Are all aisles, passageways, stairways and stairwells kept clear of tools, hoses, and trash?
Inspection Checklist GENERAL HOUSEKEEPING 1. Are all aisles, passageways, stairways and stairwells kept clear of tools, hoses, and trash? 2. Is oil, grease, or other liquids, when spilled on the floor
Important. Contents. Contact us:
Operator's Manual First Edition Ninth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall
HYDRAULIC PALLET TRUCKS
HYDRAULIC PALLET TRUCKS HYDRAULIC PALLET TRUCKS MODEL Nos: PT550 GAL & PT685 GAL PART Nos: 7630234 & 7630236 OPERATION & MAINTENANCE INSTRUCTIONS 0204 Please read these instructions carefully before operating
OPERATIONAL ADVICE WARNING: TO PREVENT SERIOUS INJURY, PLEASE READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
OPERATIONAL ADVICE WARNING: TO PREVENT SERIOUS INJURY, PLEASE READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. SAVE THIS MANUAL Keep this manual in a safe place for future reference. This
Important. Contents. Contact us:
Operator's Manual Third Edition Third Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall
Wind and Temperature Tip Over Hazard Do not add notice boards or similar
Lift & Work Platform Safety Information Safety Information: Boom Lifts Safety Information: Scissor Lifts Safety Information: Boom Lifts Power Lines Electrocution Hazard Maintain safe clearance from Electrical
Owner s Manual Gantry Cranes
Owner s Manual Gantry Cranes Fixed Height Gantry Crane MODEL NUMBER: SERIAL NUMBER: CAPACITY IN TONS: Telescoping Gantry Crane Bushman Equipment, Inc. 262-790-4200, 800338-7810, Fax 262-790-4200 www.bushman.com
KWSL2000RM ! CAUTION!! READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF THIS PRODUCT. DO NOT RETURN THIS PRODUCT TO SELLER.
Assembly & Operating Instructions KWSL2000RM 2000 Lb. 12VDC Electric Winch! CAUTION!! READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF THIS PRODUCT. DO NOT RETURN THIS PRODUCT TO SELLER.
Safelift Overhead Runway Beams & Rolling Beam Cranes
Operation & Maintenance Instructions Instructions for Safe Use Safelift Overhead Runway Beams & Rolling Beam Cranes Certification Safelift overhead runway beams and rolling beam cranes are lifting appliances
OVERHEAD CRANE SAFETY:
ERI Safety Videos DVDs, Digital Media & Custom Production 1313 OVERHEAD CRANE SAFETY: Safety Is In Your Hands Leader s Guide Safety Source Productions OVERHEAD CRANE SAFETY: Safety Is In Your Hands This
Hydraulic Hand Pallet Trucks
Operating Instructions & Parts Manual 12U124 Please read and save these instructions. Read carefully before attempting to assemble, install, operate, or maintain the product described. Protect yourself
Ground Controls. Cage Control Levers. 1) Cage/Platform 2) Cage Controls 3) Ground Controls Buttons. Ground Control Levers
P14936/01 P14939/01 1 2 3 4 5 6 Nifty HR12 (12082) 1) Cage/Platform 2) Cage Controls 3) Ground Controls Buttons 4) Ground Controls - Levers 5) Lower 6) Upper 7) Cage/Ground Selector 8) Manual Hand Pump
Operator Manual. The most important component is you. This operator manual. has information for. all models of series. B plus some options and
Operator Manual This operator manual has information for all models of series B plus some options and accessories. Some of the illustrations and information may not apply to your truck. The most important
Operator Manual. This operator manual has. information for all models. of series M plus some. options and accessories. Some of the illustrations
M S E R I E Operator Manual S This operator manual has information for all models of series M plus some options and accessories. Some of the illustrations and information may not The most apply to your
HIGH LIFT HYDRAULIC TRANSMISSION JACK K12110
HIGH LIFT HYDRAULIC TRANSMISSION JACK K12110 Distributed by Kincrome Group www.kincrome.com.au Owner s Assembly and Operating Manual SPECIFICATIONS... 2 IMPORTANT SAFETY INFORMATION... 3 UNPACKING AND
TJA2.5 ALUMINIUM TROLLEY JACK
TJA2.5 ALUMINIUM TROLLEY JACK OWNER S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE. SPECIFICATION Part Number: Product Weight: Brand: Capacity: A - Closed
SAFE OPERATING PROCEDURE LADDER - Extension
SAFE OPERATING PROCEDURE LADDER - Extension DO NOT use this equipment unless you have been instructed in its safe use and operation and given prior permission. PERSONAL PROTECTIVE EQUIPMENT PRE-OPERATIONAL
Operator s Manual. 2010, 2015, 2020, 2025 Material Lifts
Operator s Manual 2010, 2015, 2020, 2025 Material Lifts April 2005! Before operating this lift, read and understand this Operator s Manual. Become familiar with the potential hazards of this unit. Call
Model 289F. Operator s Manual for Morse Model 289F. MORStak TM Forklift-Mounted Drum Racker. The Specialist In Drum Handling Equipment
Contents Page Receiving Procedures.................... 1 Warranty............................. 1 Safety Information..................... 1-2 Machine Description................... 3 Operating Instructions....................
STRUT SPRING COMPRESSOR
OWNER S MANUAL PRODUCT CODE: 1221T STRUT SPRING COMPRESSOR Capacity Stroke Spring Coil Spring Spring Coil Net Weight (Maximum) Thickness Length Diameter 1,000kg 330mm 10-18mm 210-570mm 100-158mm 36kg Made
Parallel Lift Rack MODEL RM
Form 4401T, 09-03 Supersedes Form 4401T, 10-00 OPERATION INSTRUCTIONS Parallel Lift Rack MODEL RM Copyright 1998-2003 Hunter Engineering Company Contents 1. For Your Safety... 1 1.1 Warning/Instruction
Notice. Overhead Crane Safety and Inspection Requirements. Daily Operator Inspection Reuirements. Daily Operator Inspection Requirements
Notice Overhead Crane Safety and Inspection Requirements It is the responsibility of the Owner/User to install, inspect, test, maintain, and operate a crane or associated lifting equipment in accordance
1.5 TON ALUMINUM RACING JACK
1.5 TON ALUMINUM RACING JACK OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
Heavy Duty Engine Cranes
Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number Atd-7484 Atd-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model Atd-7484 Model Atd-7485 Atd Tools Inc. 160 Enterprise Drive, Wentzville,
Safe Operating Procedure LADDER - Single
Safe Operating Procedure LADDER - Single DO NOT use this equipment unless you have been instructed in its safe use and operation and given prior permission. PERSONAL PROTECTIVE EQUIPMENT Welds are intact.
Technical Publications AWP. Operator's Manual. Fourth Edition, First Printing Part No
Technical Publications AWP Operator's Manual Fourth Edition, First Printing Part No. 424 Operator s Manual Fourth Edition Important Read, understand and obey these safety rules and operating instructions
610 BUSHEL MANURE SPREADER
610 BUSHEL MANURE SPREADER RODA MANUFACTURING 1008 LOCUST ST. HULL, IA. 51239 Art s-way Manufacturing 712-439-2366 Co., Inc. Hwy 9 West - PO Box 288 WWW.RODAMFG.COM Armstrong, IA. 50514 U.S.A 2 INTRODUCTION
PRESENTER'S GUIDE "CRANE SAFETY" Part of the "SAFETY MEETING KIT" Series Quality Safety and Health Products, for Today...
PRESENTER'S GUIDE "CRANE SAFETY" Part of the "SAFETY MEETING KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE OF MAJOR PROGRAM POINTS The
Forklift & Tractor Jack
Forklift & Tractor Jack 10435 4 Ton Capacity ASSEMBLY & OPERATION INSTRUCTIONS SAVE THESE INSTRUCTIONS. For your safety and the safety of others around you, read carefully before attempting to install,
OPERATIONAL INSTRUCTION OVERVIEW MAINTENANCE CHECKLIST
OPERATIONAL INSTRUCTION OVERVIEW Operation Both manual and electrically powered winches develop tremendous forces; therefore, all backstops must be operated by qualified personnel only to avoid structural
BOGERT HMMWV LIFTING JACK KIT PART NR: 30M-HVBMI NSN:
BOGERT HMMWV LIFTING JACK KIT PART NR: 30M-HVBMI NSN: 5120-01-573-3382 Tire Replacement Jack Operating Instructions Model: 30M-HV Jack with BMI P40A Hydraulic Pump Bogert International Inc. 3606 N. Swallow
OPERATOR S MANUAL R-Series Roust-a-Bout
December 2017 OPERATOR S MANUAL R-Series Roust-a-Bout! Before operatingthis lift, readand understandthis Operator s Manual. Become familiar with the potentialhazards of thisunit. Call SUMNER if youhaveanyquestions.
Air Actuated Hydraulic Bottle Jacks
Air Actuated Hydraulic Bottle Jacks Operating Instructions & Parts Manual Model Number Atd-7412 Atd-7420 Capacity 12 Ton 20 Ton Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China
HOISTING APPARATUS Inspection Guidelines
HOISTING APPARATUS Inspection Guidelines This is a guide to assist in meeting the requirements of paragraph 211(2)(a) of the General Regulation 91-191 under the Occupational Health and Safety (OHS) Act.
BEFORE YOU START!! Read the safety messages on the implement as shown in your manual. Observe the rules of safety and common sense!
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable
440/880LB ELECTRIC HOIST STF-4488EH
ELECTRIC HOIST 440/880LB WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
Engine Crane Owner s Manual
Engine Crane Owner s Manual Model Number ATD04 Capacity Ton WARNING: This product may contain chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive
HOP-LP Portable Steel Dumping Hoppers Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
Element 3: Musculoskeletal Hazards and Risk Control
Manually and Mechanically Operated Load Handling Equipment There are many different types of lifting and moving equipment such as manually operated trucks and hoists and mechanically operated forklift
2 TON CAPACITY PROFESSIONAL SERIES ALUMINUM JACK OWNER'S MANUAL SPECIFICATIONS
80006 OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Warning Information 3 Setup, Operating and Preventative Maintenance 4 Troubleshooting 5 Maintenance 6 Exploded View Drawing and Replacement Parts
GRAIN AUGERS MK80 X ASSEMBLY & OPERATION MANUAL
GRAIN AUGERS ASSEMBLY & OPERATION MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property
Hydraulic Transmission Jacks
Hydraulic Transmission Jacks Operating Instructions & Parts Manual Model Number Atd-7435 Atd-7436 Atd-7437 Capacity 1100 Lb. 2000 Lb. 3000 Lb. Model Atd-7435 Model Atd-7436 Model Atd-7437 Atd Tools Inc.
25 BUSHEL MANURE SPREADER
25 BUSHEL MANURE SPREADER RODA MANUFACTURING 338 MAIN ST. HULL, IA. 51239 Art s-way Manufacturing 712-439-2366 Co., Inc. Hwy 9 West - PO Box 288 WWW.RODAMFG.COM Armstrong, IA. 50514 U.S.A 2 INTRODUCTION
CONTENTS: 5740AH - 40 Ton Air/Hydraulic Shop Press 5750AH - 50 Ton Air/Hydraulic Shop Press OWNER'S MANUAL
OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Safety Information and Warranty Information 3 Parts List 4-6 Assembly Instructions 7 Pump and Ram Assembly Instructions 8 Procedure for Bleeding Air 9 Pump
HYDRAULIC BENCH PRESS 50,000kg
OWNER S MANUAL PRODUCT CODE: 2037T HYDRAULIC BENCH PRESS 50,000kg Working Capacity Height Width Depth Weight 50,000kg 1660mm 1220mm 800mm 236kg Made in China to TQB Brands Pty Ltd specifications WARNING
Portable Lighting Equipment Operating Instructions Table of Contents
Portable Lighting Equipment Operating Instructions Table of Generac Magnum Ingersoll Rand TEREX AMIDA TEREX GENIE Model: MLT3060 Model: LIGHTSOURCE Model: Amida AL4000 series Model: TML4000N Generac Magnum
Long Chassis Hydraulic Service Jacks
Long Chassis Hydraulic Service Jacks Operating Instructions & Parts Manual Model Number Atd-7390 Atd-7391 Capacity 5 Ton 10 Ton Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China
OPERATIONS MANUAL LEVER CHAIN HOIST
OPERATIONS MANUAL LEVER CHAIN HOIST IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this hoist. Retain these instructions
EZ LINER EXPRESS USERS MANUAL
EZ LINER EXPRESS 2013 Vehicle Service Group CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies warrants for one year from date of installation and/or purchase any components of
P. & I. Pascoe Limited
P. & I. Pascoe Limited www.hh.net.nz Significant Hazard Register and Safe Operating Procedures (SOP s) Diggers / Roller / Bulldozer / Loader July 2008 Significant Hazard Register & Safe Operating Procedures
jegs.com. Installation Instructions for Ton Aluminum Floor Jack
Installation Instructions for 80077 3-Ton Aluminum Floor Jack Contents: Specifications Warning Information Setup and Operating Instructions Preventive Maintenance and Troubleshooting Hydraulic Maintenance
MODEL LR-2066 & LR-2866A HOIST INSTALLATION AND OPERATION MANUAL
TRUCK BODIES & EQUIPMENT INTERNATIONAL, Inc. Website: www.rugbymfg.com E-mail: sales@rugbymfg.com Phone: 1-800-869-9162 03 5839 MODEL LR-2066 & LR-2866A HOIST INSTALLATION AND OPERATION MANUAL Hoist Serial
Operating Instructions & Parts Manual
Hydraulic Air/Manual Bottle Jacks Operating Instructions & Parts Manual Model Number ATD-74 ATD-74 Capacity Ton 0 Ton! U.S. Patent No.'s. 5,34,73-5,946,9 This is the safety alert symbol. It is used to
DWHOIST. Drywall Hoist Assembly & Operating Instructions
DWHOIST Drywall Hoist Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information
RUTGERS UNIVERSITY POWERED INDUSTRIAL TRUCK PROGRAM
RUTGERS UNIVERSITY POWERED INDUSTRIAL TRUCK PROGRAM 9/01 1 TABLE OF CONTENTS POWERED INDUSTRIAL TRUCK PROGRAM A. PURPOSE AND SCOPE...1 B. LIFE TRUCK REQUIREMENTS...1 C. AREA REQUIREMENTS...2 D. RESPONSIBILITIES...2
Ryko Solutions, Inc. Crane and Jib Safety Program
Ryko Solutions, Inc. Crane and Jib Safety Program CONTENTS PURPOSE...3 POLICY...3 SCOPE...3 RESPONSIBILITIES...3 FITNESS FOR DUTY...4 INSPECTIONS...4 FREQUENT INSPECTION...4 PERIODIC INSPECTIONS...5 RATED
1 CLEAN BELT TABLES Apr CLEAN UNDER MOVING CONVEYOR Apr CLEAN PRODUCT CHUTES Apr CLEAN TRUCK PITS Apr-08
TABLE OF CONTENTS FOR # 1 PAGE # SHIPPING UNIT # 1 REVISED 1 CLEAN BELT TABLES Apr-08 2 CLEAN UNDER MOVING CONVEYOR Apr-08 3 CLEAN PRODUCT CHUTES Apr-08 4 CLEAN TRUCK PITS Apr-08 5 CLEAN CONVEYOR MAGNETS
Brake Fluid Exchange
Brake Fluid Exchange OJT / Practice DTOG Proficiency Exam Date: Trainee: Trainer: Service Center: Brake Fluid Exchange 1. Prepare for service Wear proper Personal Protective Equipment Recommended PPE:
Perfect Park 7000 Installation & Unloading Instructions Operating Manual
Perfect Park 7000 Installation & Unloading Instructions Operating Manual 1) Always file a claim with the truck line if the lift has been damaged! (If you don t originally notice the damage, but find some
In This Document MODULE DESCRIPTION This module provides information on the safety concerns and
Crane Safety Fact Sheet In This Document MODULE DESCRIPTION This module provides information on the safety concerns and Introduction necessary precautions you will need to be aware of when working Crane
Low Profile Service Jack
Low Profile Service Jack Operating Instructions & Parts Manual Model Number JSA200LCX Capacity 2 Ton MAC TOOLS INC. 2005 505 N. Cleveland Ave. Suite 200 Westerville, OH 43082 Printed in PRC Save these
FITTING INSTRUCTIONS NEW ATW4500 M A
FITTING INSTRUCTIONS NEW ATW4500 M73080930A INTRODUCTION Thanks for your interesting in Products, especially the ATW4500, and we sincerely hope that it will satisfy you. We not only have the professional
MXEM Manual Push/Electric Lift Stackers Service Manual
MXEM Manual Push/Electric Lift Stackers Service Manual LIFT PRODUCTS INC PO BOX 349 ELM GROVE WI 53122 262-521-5720 FAX 262-521-5725 Toll Free 877-543-8776 Model: MXEM-2200 Series (MXEM-2200-63, MXEM-2200-98,
11 OPERATION AND VERIFICATION
11 OPERATION AND VERIFICATION Section Page 11.1 PREPARATION FOR A FIRST TIME START... 11-3 11.2 STARTING THE ENGINE... 11-9 11.3 RUNNING THE ENGINE... 11-12 11.4 STOPPING THE ENGINE... 11-14 (Rev. 3/04)
"CRANE SAFETY IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "CRANE SAFETY IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE
Material Handling - Cranes, Hoists, Slings, Chain Falls, and Ratchet Hoists
Material Handling - Cranes, Hoists, Slings, Chain Falls, and Ratchet Hoists University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob
PO Box 1719 Subiaco Western Australia
INSTRUCTION MANUAL Contact BUSH WINCHES AND ANCHORS PTY LTD PO Box 1719 Subiaco Western Australia 6904 Email: info@bushwinch.com.au CONGRATULATIONS Congratulations on your purchase of the Bush Winch. You
Lineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2
Lineman s Hoist LMST0- Operating, Maintenance & Parts Manual Lineman s Hoist Follow all instructions and warnings for inspecting, maintaining and operating this hoist. The use of any hoist presents some
OPERATOR S MANUAL 7(5 & ( 8&. $5.00 P/N REV.B
OPERATOR S MANUAL &281 2817( 7(5 %$/$1&( /,)7 7758& 8&. $5.00 P/N 901345 REV.B As a lift truck operator, you are responsible for a machine that is useful, powerful, and can be hazardous if not operated
MK AUGERS POWER SWING KIT ASSEMBLY & OPERATION MANUAL
MK AUGERS POWER SWING KIT ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.
Installation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
N G 3 S p r i n g B r a k e s
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t M a n u a l N G 3 S p r i n g B r a k e s R ationalised Units for S-Cam Applications P r o d u c t M a n u a l Disclaimer The information contained
Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A
Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-440436 Ph.: 800-274-6848 Revision A1 06/2014 www.jettools.com Copyright
Inspections of Aerial Equipment
I Inspections of Aerial Equipment Milton J. Luttrell, III Aspen Aerials, Inc. nspections of aerial equipment are a requirement as set forth by the American Nations Standards Institute (ANSI). Owners of
Hydraulic Transmission Jack
Hydraulic Transmission Jack Operating Instructions & Parts Manual Model Number Atd-7430 Series A Atd-743 Series A (Air Actuated Model) Capacity 000 lbs 000 lbs Model Atd-7430 Series A! This is the safety
OnBoard Drum Major Podium
Assembly and Owner s Manual OnBoard Drum Major Podium CONTENTS CONTENTS................................................................................. 1 SAFETY...................................................................................
MR6K-48X. Mid-Rise Scissor Lift ASSEMBLY & OPERATION INSTRUCTION MANUAL. 6,000 lbs.
MR6K-48X Mid-Rise Scissor Lift 6,000 lbs. ASSEMBLY & OPERATION INSTRUCTION MANUAL November 2014 Important! Be sure to read the operating instructions before operating your lift! Getting Ready Make sure
Atd Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385
Owner's Manual Trolley Jack Model ATD-7304 Capacity 2 Ton! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol
Service Bulletin No. 3023
Service Bulletin No. 3023 MODEL TYPE SECTION/GROUP DATE D / E / J Series Coaches Service Information 4--Brakes Sept. 8, 2009 SUBJECT DISC PLUS EX225 BRAKE ACTUATOR TEST PROCEDURE CONDITIONS Service Information
Atd Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385
Owner's Manual Model RHO-7425 High Lift Transmission Jack Capacity 700 lbs.! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that
WD DODGE SUSPENSION LIFT KIT P/N
4/03/03 94-01 4WD DODGE 1500 3 SUSPENSION LIFT KIT P/N 10-46094 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are covered in separate instructions.
MGM Brakes Service Manual
MGM Brakes Service Manual MAGNUM Performance Plus Spring Brake Actuators (MJ-Series 3.00 / 76mm Long Stroke ) For: S-Cam Tamper-Resistant MAGNUM Performance Plus Spring Brake Actuators Figure 1 A B C Your
WARNING SPECIFICATIONS MODEL # A 1-1/2 TON TRANSMISSION JACK. Manufactured to comply with the ASME PASE-2014 Safety Standard.
MODEL # 791-7180 A 1-1/2 TON TRANSMISSION JACK BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING PROCEDURES, SAFETY S AND MAINTENANCE REQUIREMENTS. It is the
Stuck Draft Gear Procedure Manual Derived from AAR Manual of Standards and Recommended Practices Book B-II, RP , Pages 57 98
Stuck Draft Gear Procedure Manual Derived from AAR Manual of Standards and Recommended Practices Book B-II, RP-101-83, Pages 57 98 MINER ENTERPRISES, INC. 630-232-3000 Technical Services Direct line -
2 PCE HYDRAULIC VEHICLE POSITIONING JACKS
2 PCE HYDRAULIC VEHICLE POSITIONING JACKS 300MM WHEEL WIDTH CAPACITY STEEL FRAME CONSTRUCTION ADJUSTING RANGE 345MM-625MM K12101-2 Piece Hydraulic Vehicle Positioning Jacks (PU Castors) K12104-2 Piece
Installation Instructions
Suzuki Samurai 1 Inch and 2 Inch Body Lift Kit (SKU# SSP-BL) Installation Instructions Background: These instructions are designed for installing the 2 body lift. Our approach is to raise the entire body
New Bremen, Ohio USA 2004 PF14387-WEB Rev. 6/06 Printed in U.S.A.
New Bremen, Ohio 45869 USA 2004 PF14387-WEB Rev. 6/06 Printed in U.S.A. You Must be Trained It s the law, you must be trained and certified to operate this truck. (OSHA 1910.178, Rev. 1999) You or others
SIDE-WIND, A-FRAME TRAILER JACK. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
SIDE-WIND, A-FRAME TRAILER JACK Model 95157 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
Trailer Jack Lb. Ring Mount. Assembly & Operating Instructions.
2000 Lb. Ring Mount Trailer Jack Model 41006 Assembly & Operating Instructions www.harborfreight.com Copyright 1999 by Harbor Freight Tools. All Rights Reserved. No portion of this manual or any artwork
ICEBREAKER. The T12 model. USER MANUAL. Sah-Ko Oy Lumijoentie 6, P.O. Box 13 FI Oulu, FINLAND
ICEBREAKER The T12 model USER MANUAL Note! P13 T14 in the picture. Sah-Ko Oy Lumijoentie 6, P.O. Box 13 FI-90401 Oulu, FINLAND +358 207 448 500 www.raikomachines.com CONTENTS 1 SAFETY INSTRUCTIONS... 4
OPERATION MANUAL FOR SQUARE DRIVE & LOW PROFILE HYDRAULIC TORQUE WRENCHES NOTICE WARNING
OPERATION MANUAL FOR SQUARE DRIVE & LOW PROFILE HYDRAULIC TORQUE WRENCHES NOTICE Hydraulic Torque Wrenches are designed for installing and removing large bolts having minimal wrench clearance at offshore
Hydraulic Furniture Movers
Hydraulic Furniture Movers Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
Instruction Manual. Maximum Operating Pressure 510 bar
Single Speed Diesel Power Unit Model HPD11 Maximum Operating Pressure 510 bar ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au Phone: +61 7 3865
VEHICLE MECHANICS SAFETY RULES, POLICIES, AND PROCEDURES
VEHICLE MECHANICS SAFETY RULES, POLICIES, AND PROCEDURES The following sections provide general guidelines and requirements for vehicle maintenance safety and have been prepared to assist you based on
23-TV25 TIPPING TRAILER CAREFULLY READ THE OPERATING INSTRUCTIONS BEFORE USING THE PRODUCT! OPERATING INSTRUCTIONS TRANSLATED FROM ORIGINAL
23-TV25 TIPPING TRAILER CAREFULLY READ THE OPERATING INSTRUCTIONS BEFORE USING THE PRODUCT! OPERATING INSTRUCTIONS TRANSLATED FROM ORIGINAL INTRODUCTION Thank you for choosing a product from Kellfri AB.
Safe use of portable ladders
Safe use of portable ladders A portable ladder is primarily used for gaining access to areas above or below the ground, or other levels that are not provided with permanent access. The potential for injury
A-Series ATV Winch Operator and Installation Manual
A-Series ATV Winch Operator and Installation Manual 1 P a g e A-Series Operator and Installation Manual Thank you for choosing Superwinch. Your Superwinch is a powerful machine and whether you use it for
50 BUSHEL PTO DRIVE MANURE SPREADER
50 BUSHEL PTO DRIVE MANURE SPREADER RODA MANUFACTURING 1008 LOCUST ST. HULL, IA. 51239 712-439-2366 WWW.RODAMFG.COM 2 INTRODUCTION Thank you for purchasing a Roda Spreader. We appreciate your business.
Work Zone Toolbox Talks. Providing Excellence in Regulatory Compliance Management Systems
Providing Excellence in Regulatory Compliance Management Systems Table of Contents General Safety for Asphalt Paving...- 3 - Maintenance and Service Safety for Asphalt Paving...- 5 - Operational Safety