OPERATOR S AND PARTS MANUAL

Transcription

1 OPERATOR S AND PARTS MANUAL BUCKET LOADER ATTACHMENTS AD11 AD12 AM11 AR10 AR12 AY11 AY12 MANUAL #MP76314 M

2

3 TABLE OF CONTENTS PREFACE... 2 SAFETY PRECAUTIONS SAFETY STATEMENTS... 3 GENERAL SAFETY PRECAUTIONS EQUIPMENT SAFETY PRECAUTIONS SET-UP... 8 INSTALLATION ATTACHING & DETACHING EQUIPMENT - 200/300/400/00 Series Loaders... 9 ATTACHING & DETACHING EQUIPMENT - 600/700/800 Series Loaders ATTACHING & DETACHING EQUIPMENT - Global Carrier Series Loaders OPERATION AY11 & AY12 SERIES 4-IN-1 BUCKET OPERATION AD11 & AD12 SERIES DEBRIS BUCKET OPERATION... 1 AR10 & AR12 SERIES ROCK BUCKET OPERATION (INCLUDES OPTIONAL GRAPPLE) AM11 SERIES MANURE FORK WITH GRAPPLE OPERATION MAINTENANCE LUBRICATION & DAILY MAINTENANCE DECAL REPLACEMENT MONTHLY MAINTENANCE CYLINDER SEAL REPLACEMENT SPECIFICATIONS ATTACHMENT SPECIFICATIONS BOLT TORQUE SPECIFICATIONS PARTS AY11H 60 4-IN-1 BUCKET (300/400 Series Loader) AY11E 72 4-IN-1 BUCKET (300/400/00 Series Loader) AY12D & AY12G 72 4-IN-1 BUCKET (600/700/Global Carrier Series Loader) AY12D & AY12G 78 4-IN-1 BUCKET (600/700/Global Carrier Series Loader) AY12D & AY12G 84 4-IN-1 BUCKET (600/700/Global Carrier Series Loader) OPTIONAL TOOTHBAR ASSEMBLY (4-IN-1 Buckets) AD11H 60 DEBRIS BUCKET (300/400 Series Loader) AD11E 60 DEBRIS BUCKET (300/400/00 Series Loader) AD12D & AD12G 76 DEBRIS BUCKET (600/700/Global Carrier Series Loader) AD12D & AD12G 82 DEBRIS BUCKET (600/700/Global Carrier Series Loader) AD12D & AD12G 88 DEBRIS BUCKET (600/700/Global Carrier Series Loader) AD12D & AD12G 96 DEBRIS BUCKET (600/700/Global Carrier Series Loader) OPTIONAL BOLT ON EDGES AND TOOTHBAR ASSEMBLIES (Debris Buckets) AM11H 60 MANURE FORK AND GRAPPLE (300/400 Series Loader) AM11E 72 MANURE FORK AND GRAPPLE (300/400/00 Series Loader) AM11D & AM114G 84 MANURE FORK AND GRAPPLE (600/700/Global Carrier Series Loader) AM11D & AM11G 96 MANURE FORK AND GRAPPLE (600/700/Global Carrier Series Loader) AR10 & AR12 ROCK BUCKET (All Loaders) OPTIONAL ROCK BUCKET GRAPPLE ROCK BUCKET GRAPPLE HYDRAULIC KITS HYDRAULIC KIT FP (Adapts from 1/4 Body Couplers to 1/2 Body Couplers) CYLINDER ASSEMBLY MP10628 (AY11H 60 & AY11E 72 4-IN-1 Buckets) CYLINDER ASSEMBLY MP (AY12 Series 4-IN-1 Buckets) CYLINDER ASSEMBLY MP10786 (Debris Buckets and Manure Fork with Grapple) CYLINDER ASSEMBLY MP10767 (Rock Bucket)

4 PREFACE GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your attachment. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from field experience and engineering data. Some information may be general in nature, due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to you particular situation. The illustrations and data used in this manual were current at the time of printing. However, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification. Throughout this manual, references are made to right and left direction. These are determined by standing behind the tractor facing the direction of forward travel. LEA EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le truduzca lasmedidas de sequridad. WARNING! Never let anyone operate this unit without reading the "Safety Precautions" and "Operations" sections of this manual. Always choose hard, level ground to park the loader on and set the brake so the unit cannot roll. BEFORE OPERATION The primary responsibility for safety with this equipment falls to the operator. Make sure the equipment is operated only by trained individuals that have read and understand this manual. If there is any portion of this manual or function you do not understand, contact your local Frontier Dealer. SERVICE When servicing your product, remember to use only manufacturer replacement parts. Substitute parts may not meet the standards required for safe, dependable operation. To facilitate parts ordering, record the model and serial number of your unit in the space provided on this page. This information may be obtained from the identification plate located on the product. Any questions related to this attachment should be directed to your local Frontier dealer. MODEL: DATE: SERIAL NUMBER: (See parts section for location.)

5 SAFETY STATEMENTS THIS SYMBOL BY ITSELF OR WITH A WARNING WORD THROUGHOUT THIS MAN- UAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY OR THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH. DANGER WARNING CAUTION NOTICE THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATH WILL RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY. THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATH COULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY. THIS SIGNAL WORD IS USED WHERE MINOR INJURY COULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY. NOTICE INDICATES A PROPERTY DAMAGE MESSAGE. GENERAL SAFETY PRECAUTIONS WARNING! READ MANUAL PRIOR TO INSTALLATION Improper installation, operation, or maintenance of this equipment could result in serious injury or death. Operators and maintenance personnel should read this manual, as well as all manuals related to this equipment and the prime mover thoroughly before beginning installation, operation, or maintenance. FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE PRIME MOVER S MANUAL(S). READ AND UNDERSTAND ALL SAFETY STATEMENTS Read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all OSHA regulations, local laws, and other professional guidelines for your operation. Know and follow good work practices when assembling, maintaining, repairing, mounting, removing, or operating this equipment. KNOW YOUR EQUIPMENT Know your equipment s capabilities, dimensions, and operations before operating. Visually inspect your equipment before you start, and never operate equipment that is not in proper working order with all safety devices intact. Check all hardware to ensure it is tight. Make certain that all locking pins, latches, and connection devices are properly installed and secured. Remove and replace any damaged, fatigued, or excessively worn parts. Make certain all safety decals are in place and are legible. Keep decals clean, and replace them if they become worn or hard to read

6 GENERAL SAFETY PRECAUTIONS WARNING! WARNING! WARNING! PROTECT AGAINST FLYING DEBRIS Always wear proper safety glasses, goggles, or a face shield when driving pins in or out, or when any operation causes dust, flying debris, or any other hazardous material. LOWER OR SUPPORT RAISED EQUIPMENT Do not work under raised booms without supporting them. Do not use support material made of concrete blocks, logs, buckets, barrels, or any other material that could suddenly collapse or shift positions. Make sure support material is solid, not decayed, warped, twisted, or tapered. Lower booms to ground level or on blocks. Lower booms and attachments to the ground before leaving the cab or operator s station. USE CARE WITH HYDRAULIC FLUID PRESSURE Hydraulic fluid under pressure can penetrate the skin and cause serious injury or death. Hydraulic leaks under pressure may not be visible. Before connecting or disconnecting hydraulic hoses, read your prime mover s operator s manual for detailed instructions on connecting and disconnecting hydraulic hoses or fittings. Keep unprotected body parts, such as face, eyes, and arms as far away as possible from a suspected leak. Flesh injected with hydraulic fluid may develop gangrene or other permanent disabilities. If injured by injected fluid, see a doctor at once. If your doctor is not familiar with this type of injury, ask him to research it immediately to determine proper treatment. Wear safety glasses, protective clothing, and use a piece of cardboard or wood when searching for hydraulic leaks. DO NOT USE YOUR HANDS! SEE ILLUSTRATION. CARDBOARD HYDRAULIC HOSE OR FITTING MAGNIFYING GLASS

7 GENERAL SAFETY PRECAUTIONS WARNING! DO NOT MODIFY MACHINE OR ATTACHMENTS Modifications may weaken the integrity of the attachment and may impair the function, safety, life, and performance of the attachment. When making repairs, use only the manufacturer s genuine parts, following authorized instructions. Other parts may be substandard in fit and quality. Never modify any ROPS (Roll Over Protection Structure) or FOPS (Falling Object Protective Structure) equipment or device. Any modifications must be authorized in writing by the manufacturer. WARNING! SAFELY MAINTAIN AND REPAIR EQUIPMENT Do not wear loose clothing or any accessories that can catch in moving parts. If you have long hair, cover or secure it so that it does not become entangled in the equipment. Work on a level surface in a well-lit area. Use properly grounded electrical outlets and tools. Use the correct tools for the job at hand. Make sure they are in good condition for the task required. Wear the protective equipment specified by the tool manufacturer. SAFELY OPERATE EQUIPMENT Do not operate equipment until you are completely trained by a qualified operator in how to use the controls, know its capabilities, dimensions, and all safety requirements. See your machine s manual for these instructions. Keep all step plates, grab bars, pedals, and controls free of dirt, grease, debris, and oil. Never allow anyone to be around the equipment when it is operating. Do not allow riders on the attachment or the prime mover. Do not operate the equipment from anywhere other than the correct operator s position. Never leave equipment unattended with the engine running, or with this attachment in a raised position. Do not alter or remove any safety feature from the prime mover or this attachment. Know your work site safety rules as well as traffic rules and flow. When in doubt on any safety issue, contact your supervisor or safety coordinator for an explanation. WARNING! KNOW WHERE UTILITIES ARE Observe overhead electrical and other utility lines. Be sure equipment will clear them. When digging, call your local utilities for location of buried utility lines, gas, water, and sewer, as well as any other hazard you may encounter

8 EQUIPMENT SAFETY PRECAUTIONS TRANSPORTING ALL ATTACHMENTS Travel only with the attachment as close to the ground as possible. Drive slowly over rough ground and on slopes. When driving on public roads use safety lights, reflectors, Slow Moving Vehicle signs etc., to prevent accidents. Check local government regulations that may affect you. Do not drive close to ditches, excavations, etc., cave in could result. When on a slope, keep the load low and proceed with extreme caution. Do not drive ACROSS a steep slope - drive straight up and down. With a LOADED attachment - face the attachment and load uphill. With an EMPTY attachment - face the attachment downhill. Do not smoke when refueling. Allow room in the gas tank for expansion. Wipe up any spilled fuel. Secure cap tightly when done. MAINTAINING ALL ATTACHMENTS Before performing maintenance, lower the attachment to the ground, apply the brakes, turn off the engine, and remove the key. Worn, damaged, or illegible safety decals must be replaced. New safety decals can be ordered from your Frontier Dealer. Never work under a raised attachment. OPERATING ALL ATTACHMENTS Operate only from the operator s station. Always use the seat belt if the prime mover has a ROPS. Do not use a seat belt if there is not ROPS. Check the seat belt daily and replace if frayed or damaged. Specified lift capacities must not be exceeded. See loader specifications. An operator must not use drugs or alcohol, which can change his or her alertness or coordination. An operator taking prescription or over-the-counter drugs should seek medical advice on whether or not he or she can safely operate equipment. Never use any of these attachments for a work platform or personnel carrier. Always check locking pins before tilting or operating any attachment. Do not handle round bales unless loader is equipped with approved bale handling attachments. Do not detach loader from tractor with any of these attachments installed. Equip loader with material bucket when detaching. Stop loader gradually when lowering or lifting loads Before exiting the prime mover, lower the attachment to the ground, apply the brakes, turn off the prime mover s engine, and remove the key. Add the required amount of ballast or tractor. (See Preparing the Tractor section of the Loader Operator s Manual to determine the type and amount of ballast required.) REAR BALLAST BOX WARNING! TRACTOR STABILITY OR LOSS OF STEERING CONTROL MAY RESULT IF BALLAST BOX IS INSTALLED WITHOUT LOADER. DO NOT OPERATE TRACTOR WITH BALLAST BOX UNLESS LOADER IS INSTALLED

9 EQUIPMENT SAFETY PRECAUTIONS REAR TIRE BALLAST 200/300/400/00 SERIES LOADERS REAR TIRE BALLAST 600/700/800/GLOBAL CARRIER SERIES LOADERS ADDITIONAL PRECAUTIONS FOR AY11 & AY12 SERIES 4-IN-1 BUCKETS Make sure all loads are secure before lifting. If lifting with the clam and load appears to be unstable, lower the load, open the clam and reposition the load to attain full stability. Do not handle round bales. Do not exceed the lift capacity of your loader. See loader specifications. ADDITIONAL PRECAUTIONS FOR AD11 & AD12 SERIES DEBRIS BUCKETS Do not heap load heavy material where the combined weight of the bucket and the material could exceed the rated lifting capacity of the loader. Be sure the load does not stick out too far in front of the bucket. A light load sticking out too far can have the same tipping effect as a heavy load carried in close. Do not exceed the lift capacity of your loader. See loader specifications. Make sure all loads are secure before lifting. If lifting with the grapple and the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Do not handle round bales. ADDITIONAL PRECAUTIONS FOR AR10 & AR12 SERIES ROCK BUCKETS Be sure the load does not stick out too far in front of the bucket. A light load sticking out too far can have the same tipping effect as a heavy load carried in close. Do not exceed the lift capacity of your loader. See loader specifications. Make sure all loads are secure before lifting. If lifting with the optional grapple and the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Do not handle round bales. ADDITIONAL PRECAUTIONS FOR AM11 SERIES MANURE FORKS WITH GRAPPLE Do not exceed the lift capacity of your loader. See loader specifications. Make sure all loads are secure before lifting. If lifting with the grapple and the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Do not handle round bales

10 SET-UP GENERAL INFORMATION The AY11 & AY12 Series 4-in-1 buckets, the AD11 & AD12 Series debris buckets, the AR10 & AR12 Series rock buckets and the AM11 Series Manure Fork with Grapple are shipped completely assembled and ready to install without any set-up required. The optional grapple and hydraulic kit for the 66 and 7 rock buckets will need to be installed on the rock bucket before use. GRAPPLE ASSEMBLY AND HYDRAULIC KIT INSTALLATION Before installing the grapple assembly onto your rock bucket, park the tractor on a level surface with an overhead hoist available and with the rock bucket properly attached. Lower the bucket to the ground, turn off the engine, remove the key and apply the brakes. 1. With the grapple properly attached to the overhead hoist, lift the grapple and center it on the rock bucket. 2. Lower the rear columns into position over the top tubes on the back of the rock bucket. 3. Rotate the grapple up slightly to bring the bottom of the rear columns up against the bottom tube. Install the U-bolts suppled around the bottom tube and through the rear columns. Secure in place with the 1/2 hard flat washer and deformed lock nuts provided. 4. Install the two power and return lines to the bulkhead tees on the back right side of the grapple followed by the straight connectors and the couplers required for your loader. NOTE: The 200/300/400 loaders require MP347 straight connectors, MP1061 male coupler and MP10616 female coupler. The 600/700/Global Carrier loaders require MP3362 straight connectors and MP112 male couplers with dust caps. The 800 loader requires MP3362 straight connectors, MP112 male coupler, MP31886 female coupler, and one each dust plug and dust cap

11 INSTALLATION ATTACHING AND DETACHING EQUIPMENT (200/300/400/00 SERIES LOADERS) NOTE: Procedure is the same for all attachments. Bucket attachment shown. 1. Start tractor engine. 2. Release parking brake and/or place transmission in NEUTRAL. 3. Roll attachment back slightly and raise boom approximately 18 (460 mm) above ground level. 4. Engage tractor parking brake and/or place transmission in PARK. Shut off tractor engine and remove key.. Disconnect hydraulic couplers to attachment (if so equipped). 6. Remove the quick-lock pin (A) from each side of attachment. 7. Store pins in their storage position (B). 8. Start tractor engine. 9. Extend bucket cylinders until pin (F) releases from the holder strap (E) on each side of the attachment. 10. Lower loader boom. Place transmission in REVERSE and move away from the attachment. Holder (D) will release from hook (C) on each side of the attachment. A F B C D E 11. Set the parking brake and/or place transmission in PARK. 12. Shut off tractor engine and remove the key. 13. Attach equipment in reverse order of detaching. NOTE: On attachments with two pins (F), the 200,300 and 400 series loaders will utilize the upper pin and the 00 series loader will utilize the lower pin

12 INSTALLATION ATTACHING EQUIPMENT (600 & 700 SERIES LOADERS WITH QUIK-CHANGE LATCHES AND 800 SERIES LOADERS.) NOTE: Latch pins automatically drop on 800 series loaders to prepare the loader for attachment. A 700 SERIES 1. Extend attachment cylinders to angle attaching brackets forward /700 - Drive forward, adjusting loader height and position until the top of the bracket is aligned with the pins (A) Drive forward, adjusting loader height and position until the bar is under hooks (B) and tabs (C) are on the center side of hooks. C B 800 SERIES 3. Raise loader to engage hooks and retract attachment cylinders quickly /700 - Raise loader until you can check that pins (D) on both sides have fully dropped Raise loader until latch pins (E) are visible. Pins on both sides must extend through the attachment latch brackets. CAUTION! ALWAYS CHECK LATCH PINS BEFORE TILTING OR OPERATING ANY ATTACHMENT. E D 700 SERIES BOLT-ON LATCH SHOWN 800 SERIES. Lower attachment, shut off engine, and connect hydraulic hoses (if equipped) to the auxiliary hydraulic hook up on your loader. Installation is now complete. DETACHING EQUIPMENT (600 & 700 SERIES LOADERS WITH QUIK-CHANGE LATCHES AND 800 SERIES LOADERS) NOTE: Disconnect hydraulic attachments before backing away. 1. Level attachment approximately 6 inches (10mm) off the ground. 2. Place transmission in PARK and shut off engine. 3. Lift and rotate latches (A) up on both sides of attachment

13 INSTALLATION NOTE: Loader with Quik-Change latch plates: Pins/handles on attachment DO NOT need to be in the UP position. 800 SERIES SHOWN 4. Start tractor and slowly extend attachment cylinders until front of attachment touches ground. A. 600/700 - Lower loader until the holder clears the pockets and pins (B) Lower loader until bar (C) clears hooks (D) and back up. B 700 SERIES SHOWN 6. Shut off the engine, and disconnect hydraulic hoses. 6. Drive the tractor in reverse until it is clear of the attachment. D C 800 SERIES SHOWN NOTE: Latch pins automatically drop on 800 series loaders to prepare the loader for the next attachment. ATTACHING EQUIPMENT (GLOBAL CARRIER SERIES LOADERS) NOTE: Latch automatically closes on global carrier. 1. To prepare the loader for attachment, pull and rotate handle to open latch (A). 2. Extend attachment cylinders to angle attaching brackets forward. B A 3. Drive forward, adjusting loader height and position until the bar (B) is under hooks (C) and tabs (D) are on the center side of the hooks. 4. Raise loader and retract attachment cylinders until latch closes. A

14 INSTALLATION CAUTION! ALWAYS CHECK LATCH PINS BEFORE TILTING OR OPERATING ANY ATTACH- MENT. C D B. Lower attachment, shut off engine, and connect hydraulic hoses (if equipped) to the auxiliary hydraulic hook up on your loader. Installation is now complete DETACHING EQUIPMENT (GLOBAL CARRIER SERIES LOADERS) NOTE: Disconnect hydraulic attachments before backing away. 1. Level attachment approximately 6 inches (10 mm) off the ground. 2. Place transmission in PARK and shut off engine. A 3. Pull and rotate handle to open latch (A). 4. Start tractor and slowly extend attachment cylinders until front of attachment touches the ground.. Lower loader until the bar clears hooks and back up. 6. Shut off the engine and disconnect hydraulic hoses. 7. Drive the tractor in reverse until it is clear of the attachment

15 4-IN-1 BUCKET OPERATION AY11 & AY12 SERIES 4-IN-1 BUCKETS Read all Safety Precautions before operating your new attachment. Refer to your machines operator s manual for attachment operation. All AY11 & AY12 Series 4-IN-1 buckets are designed for various functions such as, digging with the bucket, grabbing with the clam, bulldozing, scraping or backfilling with the back blade and bottom dumping. BULLDOZING For all industry uses: road maintenance, clean up, grading, etc. CLAM Handles the hard to pick up material with ease. Complete control of loading. BACKFILLING Backfilling is no problem. BACKDRAG For working in close quarters such as between buildings and among trees. SCRAPING Cleaning yards, leveling lawns: a landscaper's bucket. BOTTOM DUMPING Ideal for trench filling or dumping into a container. GRAB Handles all undesirable loading: brush, timbers and all bulky materials. DIGGING Same as all conventional buckets

16 4-IN-1 BUCKET OPERATION ALAY11 & AY12 SERIES 4-IN-1 BUCKETS Operate the attachment only when properly seated at the operator s station. Do not exceed the lift capacity of your loader. See loader specifications. Do not handle round bales. When using the clam, lift the load slightly and make sure that the load is secure. If the load appears to be unstable, lower the load, open the clam and reposition the load to attain full stability. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle. Avoid side slope travel whenever possible. Drive up the slope to pick up a load and then down in reverse. Carry loads as close to the ground as possible. Before exiting the prime mover, lower the bucket to the ground, turn off the prime mover s engine, remove the key and apply the brakes. Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching

17 DEBRIS BUCKET OPERATION AD11 & AD12 SERIES DEBRIS BUCKETS Read all Safety Precautions before operating your new attachment. Refer to your machines operator s manual for attachment operation. All AD11 & AD12 Series debris buckets are designed to pick up bulky, unusually shaped, or long materials that would not stay in an ordinary bucket. 1. Approach the load in such a fashion that the weight will be centered on the floor of the bucket. The heaviest side should be closest to the back of the bucket and not near the bucket edge. 2. Before lifting, make certain the bucket is completely under the load and the bucket floor is level. 3. Close the grapples to their fullest extent possible and lift the bucket slightly to be certain that the load is secure. NOTE: If the load appears to be unstable, lower the bucket to the ground, open the grapples and reposition the load to attain full stability. Repeat until full stability is achieved. When using the grapples as a rake to drag materials into position for pick up, THE GRAPPLES MUST BE COMPLETELY OPEN. NOTICE Applying a raking-type force to partially open grapples will greatly magnify the fluid pressure in the hydraulic hoses, fittings, and cylinders and may cause component failure. Never heap load heavy material where the combined weight of the bucket and material could exceed the rated lifting capacity of the loader. Be sure the load does not stick out too far in front of the bucket. A light load sticking out too far can have the same tipping effect as a heavy load carried in close. Operate the attachment only when properly seated at the operator s station. Do not exceed the lift capacity of your loader. See loader specifications. Do not handle round bales. When using the grapple, lift the load slightly and make sure that the load is secure. If the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle. Avoid side slope travel whenever possible. Drive up the slope to pick up a load and then down in reverse. Carry loads as close to the ground as possible. Before exiting the prime mover, lower the bucket to the ground, turn off the prime mover s engine, remove the key and apply the brakes. Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching

18 ROCK BUCKET OPERATION AR10 & AR12 SERIES ROCK BUCKETS Read all Safety Precautions before operating your new attachment. Refer to your machines operator s manual for attachment operation. All AR10 & AR11 Series rock buckets are designed to collect rocks and debris, allowing the soil to sift through. The rake design is used for fast clean-up, ground leveling, sifting out debris and rocks, and gathering material away from buildings and obstructions. 1. Approach the load in such a fashion that the weight will be centered on the floor of the bucket. The heaviest side should be closest to the back of the bucket and not near the bucket edge. 2. Before lifting, make certain the bucket is completely under the load and the bucket floor is level. OPTIONAL GRAPPLE OPERATION The optional grapple fits all AR10 66 & 7 Series rock buckets. The grapple was designed with added structure between the grapple arms to trap and contain debris. 1. Follow Steps 1 and 2 above. 2. Close the grapples to their fullest extent possible and lift the bucket slightly to be certain that the load is secure. NOTE: If the load appears to be unstable, lower the bucket to the ground, open the grapples and reposition the load to attain full stability. Repeat until full stability is achieved. When using the grapples as a rake to drag materials into position for pick up, THE GRAPPLES MUST BE COMPLETELY OPEN. NOTICE Applying a raking-type force to partially open grapples will greatly magnify the fluid pressure in the hydraulic hoses, fittings, and cylinders and may cause component failure. Operate the attachment only when properly seated at the operator s station. Do not exceed the lift capacity of your loader. See loader specifications. Do not handle round bales. When using the grapple, lift the load slightly and make sure that the load is secure. If the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle. Avoid side slope travel whenever possible. Drive up the slope to pick up a load and then down in reverse. Carry loads as close to the ground as possible. Before exiting the prime mover, lower the bucket to the ground, turn off the prime mover s engine, remove the key and apply the brakes. Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching

19 MANURE FORK AND GRAPPLE OPERATION AM11 SERIES MANURE FORK AND GRAPPLES Read all Safety Precautions before operating your new attachment. Refer to your machines operator s manual for attachment operation. All AM11 Series manure fork and grapples are designed for moving loose hay, manure, brush and small branches. 1. Depending on the material being moved, approach so the fork tines are either centered under the load (brush or branches) or stabbing into the load (pile of hay or manure). 2. Close the grapples to their fullest extent possible and lift the attachment slightly to be certain that the load is secure. NOTE: If the load appears to be unstable, lower the forks to the ground, open the grapples and reposition the load to attain full stability. Repeat until full stability is achieved. When using the grapples as a rake to drag materials into position for pick up, THE GRAPPLES MUST BE COMPLETELY OPEN. NOTICE Applying a raking-type force to partially open grapples will greatly magnify the fluid pressure in the hydraulic hoses, fittings, and cylinders and may cause component failure. Never heap load heavy material where the combined weight of the attachment and material could exceed the rated lifting capacity of the loader. Be sure the load does not stick out too far in front of the bucket. A light load sticking out too far can have the same tipping effect as a heavy load carried in close. Operate the attachment only when properly seated at the operator s station. Do not exceed the lift capacity of your loader. See loader specifications. Do not handle round bales. When using the grapple, lift the load slightly and make sure that the load is secure. If the load appears to be unstable, lower the load, open the grapple and reposition the load to attain full stability. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle. Avoid side slope travel whenever possible. Drive up the slope to pick up a load and then down in reverse. Carry loads as close to the ground as possible. Before exiting the prime mover, lower the bucket to the ground, turn off the prime mover s engine, remove the key and apply the brakes. Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching

20 MAINTENANCE GENERAL INFORMATION Your attachment was designed to be virtually maintenance free. Very little effort is needed to keep it in top condition. It is, however, important to follow these procedures to get full performance and longevity out of the equipment. IMPORTANT: When replacing parts, use only factory approved replacement parts. Manufacturer will not claim responsibility for use of unapproved parts or accessories and/or other damages as a result of their use. LUBRICATION The only lubrication your attachment may need is the greasing of the cylinder ends and most pivot points. A grease fitting has been installed to facilitate this task. Following is a list of each of the attachments in this manual that require lubricating and the number of grease fittings. We recommend greasing all grease fittings after the initial 8 hours of operation and then every 40 hours of operation thereafter. AY11 & AY12 Series 4-IN-1 Buckets = 6 (One fitting on each end of cylinders and on each clam/back blade pivot pin.) AD11 & AD12 Series Debris Buckets = 8 (One fitting on each end of cylinders and on each grapple pin.) AR10 & AR12 Rock Bucket Grapple = 6 (One fitting on each end of cylinders and on each grapple pin.) AM11 Series Manure Fork and Grapple = 2 (One fitting on each end of cylinder.) DAILY OR EVERY 8 HOURS OF OPERATION Replace any missing bolts or nuts with approved replacement parts. Check hydraulic system for leaks. (If so equipped.) See procedure below. Visually inspect the machine for worn parts or cracked welds. Repair as necessary. Replace any damaged, illegible or missing decals. See Decal Identification and Replacement WARNING! Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Fluid escaping from a very small hole can be almost invisible. Use a piece of cardboard or wood, rather than hands to search for suspected leaks. Keep unprotected body parts, such as face, eyes, and arms as far away as possible from a suspected leak. Flesh injected with hydraulic fluid may develop gangrene or other permanent disabilities. If injured by injected fluid, see a doctor at once. If your doctor is not familiar with this type of injury, ask him or her to research it immediately to determine proper treatment. CARDBOARD HYDRAULIC HOSE OR FITTING MAGNIFYING GLASS

21 MAINTENANCE DECAL IDENTIFICATION AND REPLACEMENT Decal placement and identification for all of the attachments can be found on the parts diagrams and lists located at the back of this manual. The decals are identified by their part numbers with reductions of the actual decals located on the page. Use this information to order replacements for missing, illegible or damaged deals. When replacing parts with safety signs attached, the safety sign must also be replaced. All Safety Decals are free of charge. Contact your local Frontier dealer for replacements. REPLACING SAFETY SIGNS: 1. Clean the area of application with nonflammable solvent. 2. Wash the same area with soap and water. 3. Allow the surface to fully dry. 4. Remove the backing from the safety sign exposing the adhesive surface.. Apply the safety sign to the location shown in the parts diagram. 6. Smooth out any bubbles. Helpful Hints: (1) Decals adhere to a warm surface better than a cold surface. (2) Applying heat (from a hair dryer) will greatly improve your ability to remove a damaged decal before preparing the surface for installation of a new one. MONTHLY OR EVERY 40 HOURS OF OPERATION Check all bolts, nuts and bearings for tightness. Tighten or replace as needed. Clean equipment of dirt, oil, grease, etc. This will assist you in making a visual inspection and help avoid overlooking worn or damaged components

22 MAINTENANCE WARNING! Disconnect cylinder carefully from hydraulic hoses after removal from attachment. Hydraulic oil under pressure can cause severe injury or death. CYLINDER SEAL REPLACEMENT The following information is provided to assist you in the event you should need to repair or rebuild a hydraulic cylinder. When working on hydraulic cylinders, make sure that the work area and tools are clean and free of dirt to prevent contamination of the hydraulic system and damage to the hydraulic cylinders. Always protect the active part of the cylinder rod (the chrome section). Nicks or scratches on the surface of the rod could result in cylinder failure. Clean all parts thoroughly with a cleaning solvent before reassembly. DISASSEMBLY PROCEDURE IMPORTANT: Do not contact the active surface of the cylinder rod with the vise. Damage to the rod could result. THREADED TYPE GLAND 1. Rotate the gland with a spanner wrench counterclockwise until the gland is free of the cylinder tube. 2. Pull the cylinder rod from the cylinder tube and inspect the piston and the bore of the cylinder tube for deep scratches or galling. If damaged, the piston AND the cylinder tube must be replaced. 3. Remove the hex nut, piston, flat washer or spacer tube (if so equipped), and gland from the cylinder rod. If the cylinder rod is rusty, scratched, or bent, it must be replaced. 4. Remove and discard all the old seals. ASSEMBLY PROCEDURE IMPORTANT: Replace all seals even if they do not appear to be damaged. Failure to replace all seals may result in premature cylinder failure. NOTE: Seal kits will service most cylinders of similar bore size and rod diameter. 1. Install the cylinder rod seal in the gland first. Be careful not to damage the seal in the process, as it is somewhat difficult to install. NOTE: A special installation tool (Part #MP6349) is available to help with installing the seal. Simply fit the end of the tool over the seal so that the large prong of the tool is on the outside of the seal, and the two smaller prongs on the inside. The lip of the seal should be facing towards the tool. Rotate the handles on the tool around to wrap the seal around the end of the tool. Rotate the handles on the tool around to wrap the seal around the end of the tool

23 MAINTENANCE Now insert the seal into the gland from the inner end. Position the seal in its groove, and release and remove the tool. Press the seal into its seat the rest of the way by hand. 2. Install the new piston ring, rod wiper, O-rings and backup washers, if applicable, on the piston. Be careful not to damage the seals. Caution must be used when installing the piston ring. The ring must be stretched carefully over the piston with a smooth, round, pointed tool. 3. After installing the rod seal inside the gland, as shown in step #1, install the external seal. NOTE: Threaded glands may have been equipped with a separate O-ring and backup washer system or a polypak (all in one) type seal. Current seal kits contain a polypak (all in one) type seal to replace the discarded seal types on ALL THREADED GLANDS. 4. Slide the gland onto the cylinder rod, being careful not to damage the rod wiper. Then install the spacer, or flat washer (if so equipped), small o-ring, piston, and hex nut onto the end of the cylinder rod.. Secure the cylinder rod (mounting end) in a vise with a support at its center. Torque the nut to the amount shown for the thread diameter of the cylinder rod (see chart). Thread Diameter POUNDS - FEET 7/8" *1" /8" /4" /8" * 1" Thread Diameter WITH 1.2" Rod Diameter Min. 230 ft. lbs. Max. 20 ft. lbs. IMPORTANT: Do not contact the active surface of the cylinder rod with the vise. Damage to the rod could result. 6. Apply a lubricant (such as Lubriplate #10) to the piston and teflon ring. Insert the cylinder rod assembly into the cylinder tube. IMPORTANT: Ensure that the piston ring fits squarely into the cylinder tube and piston groove, otherwise the ring may be damaged and a leak will occur. 7. Use a spanner wrench to rotate the gland clockwise into the cylinder. Continue to rotate the gland with the spanner wrench until it is tight. WARNING! Cylinders serviced in the field are to be tested for leakage prior to the attachment being placed in work. Failure to test rebuilt cylinders could result in damage to the cylinder and/or the attachment, cause severe personal injury or even death

24 SPECIFICATIONS LOADER SERIES COMPATIBILITY: A=800 SERIES D=600/700 SERIES E=300/400/00 SERIES F=200/300/400/00 SERIES G=GLOBAL CARRIER SERIES H=300/400 SERIES AY11 & AY12 SERIES 4-IN-1 BUCKET SPECIFICATIONS Model Compatibility & Size AY11H 60 AY12D 72 AY11E 72 AY12G 72 AY12D 78 AY12G 78 AY12D 84 AY12G 84 Overall Height (inches) Overall Width (inches) Overall Length (inches) Clam Opening (inches) Attachment Weight (lbs.) Shipping Weight (lbs.) AD11 & AD12 SERIES DEBRIS BUCKET SPECIFICATIONS Model Compatibility & Size AD11H 60 AD11E 72 AD12D 76 AD12G 76 AD12D 82 AD12G 82 Overall Height (inches) Overall Width (inches) Overall Length (inches) Grapple Opening (inches) Attachment Weight (lbs.) Shipping Weight (lbs.) AD11 & AD12 SERIES DEBRIS BUCKET SPECIFICATIONS Model Compatibility & Size AD12D 88 AD12G 88 AD12D 96 AD12G 96 Overall Height (inches) Overall Width (inches) Overall Length (inches) Grapple Opening (inches) Attachment Weight (lbs.) Shipping Weight (lbs.) AR10 SERIES ROCK BUCKET SPECIFICATIONS Model Compatibility & Size AR10H AR10E 66 AR10D 7 AR10E 7 AR10G 7 Overall Height (inches) Overall Width (inches) Overall Length (inches) Opt. Grapple Opening (inches) NA Opt. Grapple Width (inches) NA Tine Diameter (inches) Tine Spacing (inches) 2 2 or 3 2 or 3 2 or 3 2 or 3 Attachment Weight (3 spacing-w/o grapple) 620 (2 Spacing) Shipping Weight (3 spacing-w/o grapple) 6 (2 Spacing) AR12 SERIES ROCK BUCKET SPECIFICATIONS Model Compatibility & Size AR12A 84 AR12D 84 AR12G 84 AR12A 93 AR12D 93 AR12G 93 Overall Height (inches) Overall Width (inches) Overall Length (inches) Opt. Grapple Opening (inches) NA NA NA Opt. Grapple Width (inches) NA NA NA Tine Diameter (inches) Tine Spacing (inches) 2 or Attachment Weight (3 spacing-w/o grapple) Shipping Weight (3 spacing-w/o grapple) AM11 SERIES MANURE FORK AND GRAPPLE SPECIFICATIONS Model Compatibility & Size AM11H 60 AM11E 72 AM11D 84 AM11G 84 AM11D 96 AM11G 96 Overall Height (inches) Overall Width (inches) Overall Length (inches) Grapple Opening (inches) Attachment Weight (lbs.) Shipping Weight (lbs.)

25 BOLT TORQUE BOLT TORQUE SPECIFICATIONS GENERAL TORQUE SPECIFICATION TABLES Use the following charts when determining bolt torque specifications when special torques are not given. Always use grade or better when replacing bolts. SAE BOLT TORQUE SPECIFICATIONS NOTE: The following torque values are for use with extreme pressure lubricants, plating or hard washer applications Increase torque 1% when using hardware that is unplated and either dry or lubricated with engine oil. SAE GRADE TORQUE SAE GRADE 8 TORQUE Bolt Size Pounds Feet Newton-Meters Pounds Feet Newton-Meters Inches Millimeters UNC UNF UNC UNF UNC UNF UNC UNF 1/ / / / / / / / / / / / / METRIC BOLT TORQUE SPECIFICATIONS NOTE: The following torque values are for use with metric hardware that is unplated and either dry or lubricated with engine oil. Reduce torque 1% when using hardware that has extreme pressure lubricants, plating or hard washer applications. Bolt head identification marks as per grade. NOTE: Manufacturing Marks Will Vary Bolt head identification marks as per grade. Size of Bolt Grade No. Pitch (mm) Pounds Feet Newton-Meters Pitch (mm) Pounds Feet Newton-Meters M M M M M M M M

26 AY11H 60 4-IN-1 BUCKET 300 & 400 SERIES LOADERS

27 AY11H 60 4-IN-1 BUCKET 300 & 400 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 4 MP170 Snap Ring 2 4 MP131 Thrust Washer 3 2 MP10769 Pivot Pin 1 x 3-7/8 4 6 MP6616 Grease Fitting 2 MP10628 Cylinder Assembly 6 1 MP1061* Male Coupler 6FBo 1/4 Body 7 1 MP10616* Female Coupler 6FBo 1/4 Body 8 4 MP347 Straight Connector 6MBo-6MJ 9 2 MP3829 1/4 Hose X 60 6FJX-6FJX 10 2 MP3498 Bulkhead Tee 6MJ-6MJ-6MJ 11 2 MP /4 Hose X 3 6FJX-6MBoX MP /4 Hose X 39 6FJX-6FJX 13 2 MP1043 3/8 UNC X 1 Hex Bolt 2 MP103 3/8 Lock Washer 2 MP1800 3/8 Hard Flat Washer 14 2 MP819 Spacer Tube 1 2 MP Pivot Pin 16 4 MP1009 1/4 UNC X 2-1/2 Hex Bolt 17 2 MP10672 Pivot Pin 1 x 4-7/ MP1629 1/4 UNC Nylock Nut 19 2 FP00737 Warning Decal, Pinch Points 20 2 FPRDL312 Warning Decal, Crushing Hazard 21 2 MP34114 Rubber Edge 22 2 MP212 Hose Clamp (Included with Back Blade) Serial Number Identification Tag Location 24 1 FP Warning Decal, Read Manual, No Riders 2 1 FPW0426 Warning Decal, Lock Pins 26 1 MP1067 Cover 27 2 MP1021 /16 UNC X 3/4 Hex Bolt 2 MP102 /16 Lock Washer 28 1 MP4011 Warning Decal, High Pressure Fluid 29 1 MP11188 Back Blade 30 1 MP Clam 31 4 MP10867 Bushing 32 2 MP11207 Bushing * Hydraulic Kit MP required to adapt 4-IN-1 buckets to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

28 AY11E 72 4-IN-1 BUCKET 300, 400 & 00 SERIES LOADERS

29 AY11E 72 4-IN-1 BUCKET 300, 400 & 00 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 4 MP170 Snap Ring 2 4 MP131 Thrust Washer 3 2 MP10769 Pivot Pin 1 x 3-7/8 4 6 MP6616 Grease Fitting 2 MP10628 Cylinder Assembly 6 1 MP1061* Male Coupler 6FBo 1/4 Body 7 1 MP10616* Female Coupler 6FBo 1/4 Body 8 4 MP347 Straight Connector 6MBo-6MJ 9 2 MP3829 1/4 Hose X 60 6FJX-6FJX 10 2 MP3498 Bulkhead Tee 6MJ-6MJ-6MJ 11 2 MP /4 Hose X 41 6FJX-6MBoX MP /4 Hose X 4 6FJX-6FJX 13 2 MP1043 3/8 UNC X 1 Hex Bolt 2 MP103 3/8 Lock Washer 2 MP1800 3/8 Hard Flat Washer 14 2 MP819 Spacer Tube 1 2 MP Pivot Pin 16 4 MP1009 1/4 UNC X 2-1/2 Hex Bolt 17 2 MP10672 Pivot Pin 1 x 4-7/ MP1629 1/4 UNC Nylock Nut 19 2 FP00737 Warning Decal, Pinch Points 20 2 FPRDL312 Warning Decal, Crushing Hazard 21 2 MP34107 Rubber Edge 22 2 MP212 Hose Clamp (Included with Back Blade) Serial Number Identification Tag Location 24 1 FP Warning Decal, Read Manual, No Riders 2 1 FPW0426 Warning Decal, Lock Pins 26 1 MP1067 Cover 27 2 MP1021 /16 UNC X 3/4 Hex Bolt 2 MP102 /16 Lock Washer 28 1 MP4011 Warning Decal, High Pressure Fluid 29 1 MP Back Blade 30 1 MP Clam 31 4 MP10867 Bushing 32 2 MP11207 Bushing * Hydraulic Kit MP required to adapt 4-IN-1 buckets to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

30 AY12D & AY12G 72 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS

31 AY12D & AY12G 72 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP112 Male Coupler 10FBo 1/2 Body 2 MP173 Male Coupler Cover 2 2 MP MBo-6MJ Straight Connector 3 2 MP /8 Hose X 60 6FJX-6FJX 4 1 MP10778 Valve Cover 3 MP1027 /16 UNC X 2-1/4 Hex Bolt 6 3 MP102 /16 Lock Washer 7 3 MP113 /16 Flat Washer 8 1 MP3721 1/4 Hose X 39 6FJX-6FJX 9 1 MP3879 1/4 Hose X 37 6FJX-6FJX 10 3 MP3434 6MBo-6MJ 90 Elbow 11 1 MP8836 Valve - Gresen 12 1 MP MBo-6MJ 90 Long Elbow 13 2 MP MJ-6FJX-6MJ Tee 14 1 MP3806 1/4 Hose X 4 6FJX-6FJX 1 1 MP /4 Hose X 43 6FJX-6FJX 16 4 MP1030 /16 UNC X 3 Hex Bolt 17 2 MP1073 Cylinder Pin 18 6 MP173 /16 UNC Nylock Nut 19 6 MP6616 Grease Fitting 20 2 MP Cylinder Assembly 21 2 MP1029 /16 UNC X 2-3/4 Hex Bolt 22 2 MP1072 Cylinder Pin 23 1 MP Back Blade (600 & 700 Series Loader) MP Back Blade (Global Carrier Series Loader) 24 1 MP Clam 2 2 MP11207 Bushing 26 2 MP1071 Pivot Pin 27 2 FP00737 Warning Decal, Pinch Points 28 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 30 1 FP Warning Decal, Read Manual, No Riders 31 1 MP4011 Warning Decal, High Pressure Fluid ITEMS #32 THROUGH #37 ARE USED ON 600 & 700 SERIES LOADERS ONLY 32 4 FP M12 Hex Nut 33 1 FP Right Latch Pin 34 2 FP Trip Pin 3 1 FP13213 Left Latch Pin 36 2 FPRHW8028 Roll Pin 37 2 FP Compression Spring

32 AY12D & AY12G 78 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS

33 AY12D & AY12G 78 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP112 Male Coupler 10FBo 1/2 Body 2 MP173 Male Coupler Cover 2 2 MP MBo-6MJ Straight Connector 3 2 MP /8 Hose X 60 6FJX-6FJX 4 1 MP10778 Valve Cover 3 MP1027 /16 UNC X 2-1/4 Hex Bolt 6 3 MP102 /16 Lock Washer 7 3 MP113 /16 Flat Washer 8 1 MP3720 1/4 Hose X 42 6FJX-6FJX 9 1 MP /4 Hose X 40 6FJX-6FJX 10 3 MP3434 6MBo-6MJ 90 Elbow 11 1 MP8836 Valve - Gresen 12 1 MP MBo-6MJ 90 Long Elbow 13 2 MP MJ-6FJX-6MJ Tee 14 1 MP /4 Hose X 48 6FJX-6FJX 1 1 MP /4 Hose X 46 6FJX-6FJX 16 4 MP1030 /16 UNC X 3 Hex Bolt 17 2 MP1073 Cylinder Pin 18 6 MP173 /16 UNC Nylock Nut 19 6 MP6616 Grease Fitting 20 2 MP Cylinder Assembly 21 2 MP1029 /16 UNC X 2-3/4 Hex Bolt 22 2 MP1072 Cylinder Pin 23 1 MP Back Blade (600 & 700 Series Loader) MP Back Blade (Global Carrier Series Loader) 24 1 MP Clam 2 2 MP11207 Bushing 26 2 MP1071 Pivot Pin 27 2 FP00737 Warning Decal, Pinch Points 28 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 30 1 FP Warning Decal, Read Manual, No Riders 31 1 MP4011 Warning Decal, High Pressure Fluid ITEMS #32 THROUGH #37 ARE USED ON 600 & 700 SERIES LOADERS ONLY 32 4 FP M12 Hex Nut 33 1 FP Right Latch Pin 34 2 FP Trip Pin 3 1 FP13213 Left Latch Pin 36 2 FPRHW8028 Roll Pin 37 2 FP Compression Spring

34 AY12D & AY12G 84 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS

35 AY12D & AY12G 84 4-IN-1 BUCKET 600, 700, GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP112 Male Coupler 10FBo 1/2 Body 2 MP173 Male Coupler Cover 2 2 MP MBo-6MJ Straight Connector 3 2 MP /8 Hose X 60 6FJX-6FJX 4 1 MP10778 Valve Cover 3 MP1027 /16 UNC X 2-1/4 Hex Bolt 6 3 MP102 /16 Lock Washer 7 3 MP113 /16 Flat Washer 8 1 MP3806 1/4 Hose X 4 6FJX-6FJX 9 1 MP /4 Hose X 43 6FJX-6FJX 10 3 MP3434 6MBo-6MJ 90 Elbow 11 1 MP8836 Valve - Gresen 12 1 MP MBo-6MJ 90 Long Elbow 13 2 MP MJ-6FJX-6MJ Tee 14 1 MP3779 1/4 Hose X 1 6FJX-6FJX 1 1 MP3807 1/4 Hose X 0 6FJX-6FJX 16 4 MP1030 /16 UNC X 3 Hex Bolt 17 2 MP1073 Cylinder Pin 18 6 MP173 /16 UNC Nylock Nut 19 6 MP6616 Grease Fitting 20 2 MP Cylinder Assembly 21 2 MP1029 /16 UNC X 2-3/4 Hex Bolt 22 2 MP1072 Cylinder Pin 23 1 MP Back Blade (600 & 700 Series Loader) MP Back Blade (Global Carrier Series Loader) 24 1 MP Clam 2 2 MP11207 Bushing 26 2 MP1071 Pivot Pin 27 2 FP00737 Warning Decal, Pinch Points 28 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 30 1 FP Warning Decal, Read Manual, No Riders 31 1 MP4011 Warning Decal, High Pressure Fluid ITEMS #32 THROUGH #37 ARE USED ON 600 & 700 SERIES LOADERS ONLY 32 4 FP M12 Hex Nut 33 1 FP Right Latch Pin 34 2 FP Trip Pin 3 1 FP13213 Left Latch Pin 36 2 FPRHW8028 Roll Pin 37 2 FP Compression Spring

36 OPTIONAL TOOTHBAR ASSEMBLY 4-IN-1 BUCKETS

37 OPTIONAL TOOTHBAR ASSEMBLY 4-IN-1 BUCKETS FP10642 OPTIONAL 60 TOOTH BAR ASSEMBLY - AY11H 60 BUCKET ONLY ITEM REQ D PART NO. DESCRIPTION Tooth Bar 2 2 MP1117 /8 UNC X 2-1/4 Hex Bolt Spacer (Used with MP127 Tooth Bar Only) 4 2 MP117 /8 Flat Washer 2 MP106 /8 Lock Washer 2 MP1230 /8 UNC Hex Nut 6 7 FPLAF1000 Replaceable Tooth Point 7 7 FPRHW8026 Replaceable Roll Pin FP10643 OPTIONAL 72 TOOTH BAR ASSEMBLY - AY11E 72 BUCKET ONLY ITEM REQ D PART NO. DESCRIPTION Tooth Bar 2 2 MP1117 /8 UNC X 2-1/4 Hex Bolt Spacer (Used with MP127 Tooth Bar Only) 4 2 MP117 /8 Flat Washer 2 MP106 /8 Lock Washer 2 MP1230 /8 UNC Hex Nut 6 8 FPLAF1000 Replaceable Tooth Point 7 8 FPRHW8026 Replaceable Roll Pin FP33823 OPTIONAL 72 TOOTH BAR ASSEMBLY - AY12D & AY12G 72 BUCKETS ITEM REQ D PART NO. DESCRIPTION 1 1 FP127 Tooth Bar 2 2 MP1781 1/2 UNC X 2 Hex Bolt 2 MP1818 1/2 UNC X 2-3/4 Hex Bolt (Use With Spacer) 3 2 MP19019 Spacer (Use as required between tooth bar and bucket.) 4 2 MP1646 1/2 Hard Flat Washer 2 MP1841 1/2 UNC Deformed Lock Nut 6 8 MP88893 Replaceable Tooth Point 7 8 MP88894 Replaceable Flex Pin FP16288 OPTIONAL 78 TOOTH BAR ASSEMBLY - AY12D & AY12G 78 BUCKETS ITEM REQ D PART NO. DESCRIPTION 1 1 FP1611 Tooth Bar 2 2 MP1781 1/2 UNC X 2 Hex Bolt Spacer (Used with MP127 Tooth Bar Only) 4 2 MP1646 1/2 Hard Flat Washer 2 MP1841 1/2 UNC Deformed Lock Nut 6 8 MP88893 Replaceable Tooth Point 7 8 MP88894 Replaceable Flex Pin FP16193 OPTIONAL 84 TOOTH BAR ASSEMBLY - AY12D & AY12G 84 BUCKETS ITEM REQ D PART NO. DESCRIPTION 1 1 FP1613 Tooth Bar 2 2 MP1781 1/2 UNC X 2 Hex Bolt Spacer (Used with MP127 Tooth Bar Only) 4 2 MP1646 1/2 Hard Flat Washer 2 MP1841 1/2 UNC Deformed Lock Nut 6 9 MP88893 Replaceable Tooth Point 7 9 MP88894 Replaceable Flex Pin

38 AD11H 60 DEBRIS BUCKET 300 & 400 SERIES LOADERS

39 AD11H 60 DEBRIS BUCKET 300 & 400 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 1 MP1061* Male Coupler 6FBo 1/4 Body 2 1 MP10616* Female Coupler 6FBo 1/4 Body 3 2 FP /4 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit - Cylinder MP FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X 1-1/2 Hex Bolt 6 MP12 3/8 SAE Flat Washer 6 FP819 Spacer Tube 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 4-1/32 Long 12 2 FP MFS-6MBo Long 90 Elbow 13 2 FPRHW7103 /16 UNC Center Dented Lock Nut 14 4 MP113 /16 Flat Washer 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 16 1 MP8836 Check Valve 17 2 FPLAF3412 Rubber Edge 18 2 FP Cylinder Pin 3-1/32 Long 19 1 FP Bucket 20 4 MP6616 Grease Fitting 21 2 FP Grapple Pivot Pin 22 1 FP Right Grapple 23 4 FPLAF917 Replacement Bushing 24 1 FP Left Grapple 2 2 FP00737 Warning Decal, Pinch Points 26 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 28 1 FP Warning Decal, Read Manual, No Riders 29 1 FPW0426 Warning Decal, Lock Pins 30 1 MP4011 Warning Decal, High Pressure Fluid * Hydraulic Kit MP needed to adapt debris buckets to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

40 AD11E 72 DEBRIS BUCKET 300, 400 & 00 SERIES LOADERS

41 AD11E 72 DEBRIS BUCKET 300, 400 & 00 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 1 MP1061* Male Coupler 6FBo 1/4 Body 2 1 MP10616* Female Coupler 6FBo 1/4 Body 3 2 FP /4 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 6 FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X 1-1/2 Hex Bolt 6 FP819 Spacer Tube 6 MP12 3/8 SAE Flat Washer 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 4-1/32 Long 12 2 FP MFS-6MBo Long 90 Elbow 13 2 FPRHW7103 /16 UNC Center Dented Lock Nut 14 4 MP113 /16 Flat Washer 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 16 1 MP8836 Check Valve 17 2 FPLAF3412 Rubber Edge 18 2 FP Cylinder Pin 3-1/32 Long 19 1 FP Bucket 20 4 MP6616 Grease Fitting 21 2 FP Grapple Pivot Pin 22 1 FP Right Grapple 23 4 FPLAF917 Replacement Bushing 24 1 FP Left Grapple 2 2 FP00737 Warning Decal, Pinch Points 26 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 28 1 FP Warning Decal, Read Manual, No Riders 29 1 FPW0426 Warning Decal, Lock Pins 30 1 MP4011 Warning Decal, High Pressure Fluid * Hydraulic Kit MP needed to adapt debris buckets to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

42 AD12D & AD12G 76 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS

43 AD12D & AD12G 76 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 2 FP /2 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 6 FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X 1-1/2 Hex Bolt 6 MP12 3/8 SAE Flat Washer 6 FP819 Spacer Tube 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 3-1/32 Long 12 2 FP Cylinder Pin 4-1/32 Long 13 2 FP MFS-6MBo Long 90 Elbow 14 1 MP8836 Check Valve 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 2 MP113 /16 Flat Washer 2 FPRHW7103 /16 UNC Center Dented Lock Nut 16 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 17 2 FP Trip Pin (600 & 700 Series Loader ONLY) 18 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 19 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 20 2 FP Compression Spring (600 & 700 Series Loader ONLY) 21 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 22 2 FPLAF3412 Rubber Edge 23 2 FP Grapple Pivot Pin 24 4 MP6616 Grease Fitting 2 4 FPLAF944 Replacement Bushing 26 1 FP Right Grapple 27 1 FP Left Grapple 28 1 FP Bucket (Global Carrier Series Loader) 1 FP Bucket (600 & 700 Series Loader) 29 2 FP00737 Warning Decal, Pinch Points 30 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 32 1 FP Warning Decal, Read Manual, No Riders 33 1 MP4011 Warning Decal, High Pressure Fluid

44 AD12D & AD12G 82 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS

45 AD12D & AD12G 82 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 2 FP /2 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 6 FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X1-1/2 Hex Bolt 6 MP12 3/8 SAE Flat Washer 6 FP819 Spacer Tube 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 3-1/32 Long 12 2 FP Cylinder Pin 4-1/32 Long 13 2 FP MFS-6MBo Long 90 Elbow 14 1 MP8836 Check Valve 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 2 MP113 /16 Flat Washer 2 FPRHW7103 /16 UNC Center Dented Lock Nut 16 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 17 2 FP Trip Pin (600 & 700 Series Loader ONLY) 18 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 19 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 20 2 FP Compression Spring (600 & 700 Series Loader ONLY) 21 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 22 2 FPLAF3412 Rubber Edge 23 2 FP Grapple Pivot Pin 24 4 MP6616 Grease Fitting 2 4 FPLAF944 Replacement Bushing 26 1 FP Right Grapple 27 1 FP Left Grapple 28 1 FP Bucket (Global Carrier Series Loader) 1 FP Bucket (600 & 700 Series Loader) 29 2 FP00737 Warning Decal, Pinch Points 30 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 32 1 FP Warning Decal, Read Manual, No Riders 33 1 MP4011 Warning Decal, High Pressure Fluid

46 AD12D & AD12G 88 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS

47 AD12D & AD12G 88 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 2 FP /2 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 6 FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X1-1/2 Hex Bolt 6 MP12 3/8 SAE Flat Washer 6 FP819 Spacer Tube 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 3-1/32 Long 12 2 FP Cylinder Pin 4-1/32 Long 13 2 FP MFS-6MBo Long 90 Elbow 14 1 MP8836 Check Valve 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 2 MP113 /16 Flat Washer 2 FPRHW7103 /16 UNC Center Dented Lock Nut 16 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 17 2 FP Trip Pin (600 & 700 Series Loader ONLY) 18 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 19 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 20 2 FP Compression Spring (600 & 700 Series Loader ONLY) 21 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 22 2 FPLAF3412 Rubber Edge 23 2 FP Grapple Pivot Pin 24 4 MP6616 Grease Fitting 2 4 FPLAF944 Replacement Bushing 26 1 FP Right Grapple 27 1 FP Left Grapple 28 1 FP Bucket (Global Carrier Series Loader) 1 FP Bucket (600 & 700 Series Loader) 29 2 FP00737 Warning Decal, Pinch Points 30 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 32 1 FP Warning Decal, Read Manual, No Riders 33 1 MP4011 Warning Decal, High Pressure Fluid

48 AD12D & AD12G 96 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS

49 AD12D & AD12G 96 DEBRIS BUCKET 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 2 FP /2 Hose X 60 6FFS-6MBo 4 2 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 6 FP MFS-6MBo 90 Elbow 6 2 FP /4 Hose X 44 6FFS-6FFS 7 1 FP /4 Hose X 36 6FFS-6FFS 8 2 FP MFS-6MFS-6FFS Tee 9 1 FP /4 Hose X 0 6FFS-6FFS 10 6 MP104 3/8 UNC X1-1/2 Hex Bolt 6 MP12 3/8 SAE Flat Washer 6 FP819 Spacer Tube 6 MP1837 3/8 UNC Torque Lock Nut 11 2 FP Cylinder Pin 3-1/32 Long 12 2 FP Cylinder Pin 4-1/32 Long 13 2 FP MFS-6MBo Long 90 Elbow 14 1 MP8836 Check Valve 1 2 MP1027 /16 UNC X 2-1/4 Hex Bolt 2 MP113 /16 Flat Washer 2 FPRHW7103 /16 UNC Center Dented Lock Nut 16 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 17 2 FP Trip Pin (600 & 700 Series Loader ONLY) 18 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 19 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 20 2 FP Compression Spring (600 & 700 Series Loader ONLY) 21 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 22 2 FPLAF3412 Rubber Edge 23 2 FP Grapple Pivot Pin 24 4 MP6616 Grease Fitting 2 4 FPLAF944 Replacement Bushing 26 1 FP Right Grapple 27 1 FP Left Grapple 28 1 FP Bucket (Global Carrier Series Loader) 1 FP Bucket (600 & 700 Series Loader) 29 2 FP00737 Warning Decal, Pinch Points 30 2 FPRDL312 Warning Decal, Crushing Hazard Serial Number Identification Tag Location 32 1 FP Warning Decal, Read Manual, No Riders 33 1 MP4011 Warning Decal, High Pressure Fluid

50 OPTIONAL BOLT ON EDGES AND TOOTHBAR ASSEMBLIES DEBRIS BUCKETS

51 OPTIONAL BOLT ON EDGES AND TOOTHBAR ASSEMBLIES DEBRIS BUCKETS ITEM REQ D PART NO. DESCRIPTION 1 1 FP Toothbar Assembly without Bolt On Edge 1 FP Toothbar Assembly without Bolt On Edge 1 FP Toothbar Assembly without Bolt On Edge 1 FP Toothbar Assembly without Bolt On Edge 2 1 FP Toothbar Assembly with Bolt On Edge 1 FP Toothbar Assembly with Bolt On Edge 1 FP Toothbar Assembly with Bolt On Edge 1 FP Toothbar Assembly with Bolt On Edge 3 1 FP Bolt On Edge Assembly 1 FP Bolt On Edge Assembly 1 FP Bolt On Edge Assembly 1 FP Bolt On Edge Assembly 4 2 MP1141 3/4 UNC X 2-1/2 Hex Bolt 2 MP118 3/4 Flat Washer 6 2 MP107 3/4 Lock Washer 7 2 MP1231 3/4 UNC Hex Nut 8 Varies FPLAF1029 Replacement Tooth Point 9 Varies FPLAF1018 Replacement Spring Pin with Rubber Insert 10 Varies FPRHW771 3/4 UNC Hex Nut - Grade 8 11 Varies MP107 3/4 Lock Washer 12 Varies FPRHW2767 3/4 UNC X 2-1/2 Plow Bolt - Grade

52 AM11H 60 MANURE FORK AND GRAPPLE 300 & 400 SERIES LOADERS

53 AM11H 60 MANURE FORK AND GRAPPLE 300 & 400 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 1 FP10616* Female Coupler 6FBo 1/4 Body 2 1 FP1061* Male Coupler 6FBo 1/4 Body 3 1 FP /4 Hose X 81 6FFS-6MBo 4 1 FP /4 Hose X 72 6FFS-6MBo 2 FP MFS-6MBo 90 Elbow 6 1 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 7 2 MP104 3/8 UNC X1-1/2 Hex Bolt 2 MP12 3/8 SAE Flat Washer 2 FP819 Spacer Tube 2 MP1837 3/8 UNC Torque Lock Nut 8 2 FP Cylinder Pin 3-1/32 Long 9 4 FPRHW4103 3/4 UNC X 1-3/4 Socket Head Shoulder Bolt 4 MP129 3/4 SAE Flat Washer 4 MP128 /8 SAE Flat Washer 4 MP1839 /8 UNC Torque Lock Nut 10 1 FP13277 Grapple 11 4 MP1141 3/4 UNC X 2-1/2 Hex Bolt 4 MP129 3/4 SAE Flat Washer 4 MP1936 3/4 UNC Torque Lock Nut 12 8 FPLAF9481 Replacement Bushing 13 1 FP Back Frame 14 8 FP Fork Tine 8 FP Replacement Nut 1 2 FPRDL312 Warning Decal, Crushing Hazard 16 1 FP Warning Decal, Read Manual, No Riders 17 1 MP4011 Warning Decal, High Pressure Fluid 18 1 FPW0426 Warning Decal, Lock Pins Serial Number Identification Tag Location 20 2 FP00737 Warning Decal, Pinch Points * Hydraulic Kit MP needed to adapt manure fork and grapple to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

54 AM11E 72 MANURE FORK AND GRAPPLE 300, 400 & 00 SERIES LOADERS

55 AM11E 72 MANURE FORK AND GRAPPLE 300, 400 & 00 SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 1 FP10616* Female Coupler 6FBo 1/4 Body 2 1 FP1061* Male Coupler 6FBo 1/4 Body 3 1 FP /4 Hose X 81 6FFS-6MBo 4 1 FP /4 Hose X 72 6FFS-6MBo 2 FP MFS-6MBo 90 Elbow 6 1 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 7 2 MP104 3/8 UNC X1-1/2 Hex Bolt 2 MP12 3/8 SAE Flat Washer 2 FP819 Spacer Tube 2 MP1837 3/8 UNC Torque Lock Nut 8 2 FP Cylinder Pin 3-1/32 Long 9 4 FPRHW4103 3/4 UNC X 1-3/4 Socket Head Shoulder Bolt 4 MP129 3/4 SAE Flat Washer 4 MP128 /8 SAE Flat Washer 4 MP1839 /8 UNC Torque Lock Nut 10 1 FP13277 Grapple 11 4 MP1141 3/4 UNC X 2-1/2 Hex Bolt 4 MP129 3/4 SAE Flat Washer 4 MP1936 3/4 UNC Torque Lock Nut 12 8 FPLAF9481 Replacement Bushing 13 1 FP Back Frame 14 9 FP Fork Tine 9 FP Replacement Nut 1 2 FPRDL312 Warning Decal, Crushing Hazard 16 1 FP Warning Decal, Read Manual, No Riders 17 1 MP4011 Warning Decal, High Pressure Fluid 18 1 FPW0426 Warning Decal, Lock Pins Serial Number Identification Tag Location 20 2 FP00737 Warning Decal, Pinch Points * Hydraulic Kit MP needed to adapt manure fork and grapple to 1/2 Body couplers which are required for 3rd function attachment on 00 series loaders

56 AM11D & AM11G 84 MANURE FORK AND GRAPPLE 600, 700 & GLOBAL CARRIER SERIES LOADERS

57 AM11D & AM11G 84 MANURE FORK AND GRAPPLE 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 1 FP /4 Hose X 81 6FFS-6MBo 4 1 FP /4 Hose X 72 6FFS-6MBo 2 FP MFS-6MBo 90 Elbow 6 1 MP10786 Cylinder Assembly - MP4136 Replacement Cylinder Seal Kit 7 2 MP104 3/8 UNC X1-1/2 Hex Bolt 2 MP12 3/8 SAE Flat Washer 2 FP819 Spacer Tube 2 MP1837 3/8 UNC Torque Lock Nut 8 2 FP Cylinder Pin 3-1/32 Long 9 4 FPRHW4103 /8 UNC X 1.7 Socket Head Shoulder Bolt 4 MP129 3/4 SAE Flat Washer 4 MP128 /8 SAE Flat Washer 4 MP1839 /8 UNC Torque Lock Nut 10 1 FP13277 Grapple 11 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 12 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 13 2 FP Trip Pin (600 & 700 Series Loader ONLY) 14 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 1 2 FP Compression Spring (600 & 700 Series Loader ONLY) 16 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 17 4 MP1141 3/4 UNC X 2-1/2 Hex Bolt 4 MP129 3/4 SAE Flat Washer 4 MP1936 3/4 UNC Torque Lock Nut 18 8 FPLAF9481 Replacement Bushing 19 1 FP Back Frame (600 & 700 Series Loader) 1 FP Back Frame (Global Carrier Series Loader) FP Fork Tine 10 FP Replacement Nut 21 2 FPRDL312 Warning Decal, Crushing Hazard 22 1 FP Warning Decal, Read Manual, No Riders 23 1 MP4011 Warning Decal, High Pressure Fluid Serial Number Identification Tag Location 2 2 FP00737 Warning Decal, Pinch Points 76314

58 AM11D & AM11G 96 MANURE FORK AND GRAPPLE 600, 700 & GLOBAL CARRIER SERIES LOADERS

59 AM11D & AM11G 96 MANURE FORK AND GRAPPLE 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION 1 2 MP17139 Male Coupler 8FBo 1/2 Body 2 2 MP3338 8MBo-6FBo Straight Connector 3 1 FP /4 Hose X 81 6FFS-6MBo 4 1 FP /4 Hose X 72 6FFS-6MBo 2 FP MFS-6MBo 90 Elbow 6 1 MP10786 Cylinder Assembly - MP41361 Replacement Cylinder Seal Kit 7 2 MP104 3/8 UNC X1-1/2 Hex Bolt 2 MP12 3/8 SAE Flat Washer 2 FP819 Spacer Tube 2 MP1837 3/8 UNC Torque Lock Nut 8 2 FP Cylinder Pin 3-1/32 Long 9 4 FPRHW4103 /8 UNC X 1.7 Socket Head Shoulder Bolt 4 MP129 3/4 SAE Flat Washer 4 MP128 /8 SAE Flat Washer 4 MP1839 /8 UNC Torque Lock Nut 10 1 FP13277 Grapple 11 4 FP M12 Hex Nut (600 & 700 Series Loader ONLY) 12 1 FP Right Latch Pin (600 & 700 Series Loader ONLY) 13 2 FP Trip Pin (600 & 700 Series Loader ONLY) 14 2 FPRHW8028 Roll Pin (600 & 700 Series Loader ONLY) 1 2 FP Compression Spring (600 & 700 Series Loader ONLY) 16 1 FP13213 Left Latch Pin (600 & 700 Series Loader ONLY) 17 4 MP1141 3/4 UNC X 2-1/2 Hex Bolt 4 MP129 3/4 SAE Flat Washer 4 MP1936 3/4 UNC Torque Lock Nut 18 8 FPLAF9481 Replacement Bushing 19 1 FP Back Frame (600 & 700 Series Loader) 1 FP Back Frame (Global Carrier Series Loader) FP Fork Tine 12 FP Replacement Nut 21 2 FPRDL312 Warning Decal, Crushing Hazard 22 1 FP Warning Decal, Read Manual, No Riders 23 1 MP4011 Warning Decal, High Pressure Fluid Serial Number Identification Tag Location 2 2 FP00737 Warning Decal, Pinch Points

60 AR10 & AR12 SERIES ROCK BUCKET 300, 400, 00, 600, 700 & GLOBAL CARRIER SERIES LOADERS

61 AR10 & AR12 SERIES ROCK BUCKET 300, 400, 00, 600, 700 & GLOBAL CARRIER SERIES LOADERS ITEM REQ D PART NO. DESCRIPTION Rock Bucket with 2 Tine Spacing 1 1 MP10862 AR10H Rock Bucket (300/400 Series Loaders) 1 MP AR10E 66 Rock Bucket (300/400/00 Series Loaders) 1 MP AR10E 7 Rock Bucket (300/400/00 Series Loaders) 1 MP11131 AR10D 7 Rock Bucket (600/700 Series Loaders) 1 MP10972 AR10G 7 Rock Bucket (Global Carrier Series Loader) Rock Bucket with 3 Tine Spacing 2 1 MP89622 AR10E 66 Rock Bucket (300/400/00 Series Loaders) 1 MP8964 AR10E 7 Rock Bucket (300/400/00 Series Loaders) 1 MP11132 AR10D 7 Rock Bucket (600/700 Series Loaders) 1 MP10973 AR10G 7 Rock Bucket (Global Carrier Series Loader) 1 MP AR12A 84 Rock Bucket (800 Series Loader) 1 MP11133 AR12D 84 Rock Bucket (600/700 Series Loaders) 1 MP10974 AR12G 84 Rock Bucket (Global Carrier Series Loader) 1 MP AR12A 93 Rock Bucket (800 Series Loader) 1 MP11134 AR12D 93 Rock Bucket (600/700 Series Loaders) 1 MP AR12G 93 Rock Bucket (Global Carrier Series Loader) 3 4 MP88798 Plastic Plug (All 66 and 7 Rock Buckets) Serial Number Identification Tag Location 1 FP Warning Decal, Read Manual, No Riders 6 1 FPW0426 Warning Decal, Lock Pins (300/400/00 Series Loaders) ITEMS #7 THROUGH #12 ARE USED ON 600 & 700 SERIES LOADERS ONLY 7 4 FP M12 Hex Nut 8 1 FP Right Latch Pin 9 2 FP Trip Pin 10 1 FP13213 Left Latch Pin 11 2 FPRHW8028 Roll Pin 12 2 FP Compression Spring

62 OPTIONAL ROCK BUCKET GRAPPLE AR10 SERIES 66 & 7 ROCK BUCKETS