WARNING. Baseplates Toyota Solara SLE Installation Instructions BX3774. Serial Number

Transcription

1 Serial Number Baseplates Toyota Solara SLE Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge to do fit work. When necessary, Blue Ox Dealers can be found at or by contacting our 24/7 Customer Care Department at (888) Many Blue Ox Baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use hardware supplied in the hardware kit or existing hardware specified in the Baseplate Towing. Confirm the towability and pre-towing procedures for your vehicle with the owner s manual or contact the vehicle s manufacturer for specific towing procedures. You can also contact REMCO for additional information at 1(800) Attachment Tab Height: 13.5 Attachment Tab Width: 18 Bolt Torque Specifications Torque in Foot-Pounds per Metric Bolts Bolt Size Grade 8.8 Grade MM 6 8 8MM MM MM MM Bolt Torque Specifications Torque in Foot-Pounds per Inch Bolts Bolt Size Grade 5 Grade 8 1/ / / / / / ! WARNING Failure to read and follow these instructions could result in separation of the towed vehicle from the tow bar, causing property damage, loss of towed vehicle, personal injury or death. Page 1 of /07

2 Toyota Solara SLE Parts List Ref. No. Qty. Part # Description Weldment, Base Plate, Weldment, 1/2 Nut Wire Weldment, Nut Plate, 1/4 x 1 x 1, 3/ Weldment, 3/8 Nut Plate, w 1/2 Wire /2-13 x 1 1/4 Hex Bolt, Grd. 5, ZP /2 Lock Washer, ZP /8-16 x 1 1/4 Hex Head Bolt, Grd. 5, ZP /8 Lock Washer, ZP /8-16 Hex Nut, ZP #12-14 x 1 Self Drilling Screw, ZP #10-32 x 1/2 Slot Round Head Screw #10 Lock Washer #10-32 Hex Nut Adapter, 4 Way Connector Attachment, Assembly, SF/SB, 1 Hole Cap Plug, Black (not shown) Quicklink, 3/8, ZP (not shown) Baseplate Safety Cable, 36 Class III (not shown) Tools Required Loctite RED 9/16 Socket 10MM Socket 13/32 Drill Bit Reciprocating Saw Tape Measure Utility Knife Phillips Screwdriver Flat Screwdriver Important: Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue Ox Dealer or Distributor. Page 2 of /07

3 Toyota Solara SLE Vehicle Weight: The weight of this vehicle is near the Class III, 5,000 lb. rating limitations. Some models, depending on options, may well exceed this 5,000 lb. rating. Be sure to confirm the weight of your individual vehicle before towing. As of 1999, the Aventa II is now 10,000 lbs. and either the Aventa II or the Aventa LX tow bar must be used for these applications. Tow Bar Adapters are NOT to be used with vehicles weighing over 5,000 lbs. Installation Notes: The fascia metal bumper and air baffle are removed and reinstalled during installation of the baseplate. Drilling is required. Trimming of the fascia is required. The dimensional variations between otherwise identical vehicles can be considerable. While the baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for auto manufacturer s tolerances. These minor adjustments may include filing a hole slightly, bending electrical rods and/ or bending end plates. : 1. Using a Phillips flat screwdriver, remove one plastic push pin and one metric from both sides. There is also one push pin from the center by the hood latch to remove. Set push pins and bolts aside to be reinstalled later. 2. Using a Phillips flat screw driver turn the push pin horizontally then remove. 1 2 The BX8869 Bulb and Socket Wiring Kit is recommended for this vehicle. 3. Using a 10MM socket, remove one metric bolt inside front wheel well on fascia s upper corner. Do this on both sides of vehicle. Set bolts aside to be reinstalled later. 3 Page 3 of /07

4 Toyota Solara SLE 4. Using 10MM socket, remove seven metric bolts underneath the fascia Install nut plates through the top, and install one from the bottom (gray arrow). Reinstall metal bumper. Using the base plate as a template, drill a hole into the bottom of the metal bumper with the 13/32" drill bit, on both sides. Insert the 3/8-16 nut plate with the 12 inch wire into the opening on the front of bumper to align with drilled hole, tighten the 3/8-16 hex bolt and lock washer, on both sides Pull the styrofoam off, unclip the four clips across the top of the metal bumper. Remove the bolts with a 14MM socket from both sides. Set aside for later reinstallation Using the baseplate as a template, drill the needed holes with a 3/8 drill bit. The larger bolt is the existing hole (gray arrow). Do this to both sides. Page 4 of / Reinstall molded styrofoam on the front of metal bumper and fascia. 9. The dimensional variations between otherwise identical cars can be considerable. While the base plate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for auto manufacturers' tolerances. These minor adjustments may include filing a hole slightly, bending electrical rods, adding shims and/ or bending endplates. Using a good quality paint, spray cut edges of frame to prevent rusting. BE SURE TO USE LOCTITE RED ON ALL BOLTS BEFORE TIGHTENING. TIGHTEN ALL BOLTS ACCORDING TO THE TORQUE CHART ON THE FRONT PAGE OF THESE INSTRUCTIONS OR ON PAGE 3 OF THE BASEPLATE TOWING GENERAL INSTRUCTIONS. Be sure that ALL electrical connections are plugged in properly and functioning BEFORE installing the fascia. DEALER or INSTALLER: Be certain the user receives the instruction sheets for their products.

5 Toyota Solara Customer Service Commitment Shown without removable tabs installed. Blue Ox is focused on providing exemplary customer service, as observed in our mission statement and guiding principles. In accordance with this objective, Blue Ox is proud to provide services such as repairs and general maintenance of Blue Ox products at over 150 RV Rallies. Look for our Destination America or Blue Ox Racing service crews at the next rally or race that you attend. If you were not present, you will find an informative, personalized note explaining any services that may have been performed to your Blue Ox products. Blue Ox also offers educational seminars at rallies and through our Park and Resort teams. In addition, Blue Ox customers visiting our factory may take advantage of the well-equipped Blue Ox RV park at no charge to you, our valued and appreciated customer. Shown with removable tabs installed. Page 5 of / Blue Ox One Mill Road, Industrial Park Pender, Nebraska Phone: (402) Fax: (402)

6 General Information 1. Ensure that your product(s) are registered online at It is crucial to register your product(s) so that you may be alerted of product offerings, updates, upgrades, maintenance and safety bulletins, and/ or recalls. 2. It is the owner s responsibility to inspect all towing equipment for cracked welds, missing or worn parts and loose bolts before each towing trip. Be sure to use Loctite Red on all bolts and tighten to the recommended specifications. 3. It is the owner s responsibility to hook up all towing equipment per manufacturer s instructions/ recommendations. 4. Remove the attachment tabs when not in use (if applicable). Notice To Baseplate Installer 1. It is YOUR responsibility to watch for: Oil cooler and air conditioner lines Electrical wires and hoses Missing parts or attaching points on the frame ** If the baseplate is improperly installed and is against a wire or hose, it could cause fluid leaks or electrical shorts some time after the actual baseplate installation. Permanent Baseplate Safety Cable Installation Permanent baseplate safety cables are strongly recommended when towing a vehicle with a tow bar. The principle function of the permanent baseplate safety cables is to prevent the towed vehicle from breaking loose in the event the connection between the frame of the towed vehicle and the baseplate fails or becomes disconnected. The cables must be connected from the baseplate to the frame rail or cross member of the vehicle s frame. The illustrations below show the possible arrangements recommended by Blue Ox. Each permanent baseplate safety cable must have an adequate weight rating for the towing system. The weight rating of the two (2) cables together will not qualify. Do not mount the permanent baseplate safety cables against wires, hoses or brake lines. These permanent baseplate safety cables should remain installed as long as the baseplate is installed on the vehicle. Permanent baseplate safety cables are to be used in conjunction with, and NOT a replacement for legally required safety cables attaching the towed vehicle to the towing vehicle. 5/11/15