CX130C. Swing mechanism. Swing torque 24,400 lb ft (33,000 N m) Length 12 ft 4 in (3.76 m) Track gauge 6 ft 6 in (1.99 m)

Size: px
Start display at page:

Download "CX130C. Swing mechanism. Swing torque 24,400 lb ft (33,000 N m) Length 12 ft 4 in (3.76 m) Track gauge 6 ft 6 in (1.99 m)"

Transcription

1 CX130C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED engine Model Isuzu AM-4JJ1X, Tier 4 Interim Certified (Cooled EGR) Fuel Type Cylinders Requires ultra low-sulfur fuel B5 biodiesel tolerant Water-cooled, 4-cycle, high pressure common rail system. Turbo-charged with air cooled intercooler, DPD system 4-cylinder in-line Displacement 183 in 3 (3.0 L) Bore / Stroke Fuel injection Fuel filter 3.76 in x 4.13 in (95.4 mm x mm) Direct injection (electronic) Replaceable, full flow spin-on cartridge Air filter Dry type element w/ warning restriction indicator Oil filter Replaceable, full flow spin-on cartridge Engine oil operating angle ratings: Side-to-side Rated 35 Fore and aft Rated 35 Net horsepower SAE J hp ( RPM Net maximum torque SAE J lbf ft (359 N 1600 RPM Cooling 110 to -13 F (43 to -25 C) at 55% concentration Oil Requires low-ash oil (CJ-4) Service capacities Fuel tank 69 gal (260 L) Hydraulic system 41 gal (157 L) Hydraulic tank 22 gal (82 L) Engine oil w/ filter 4.5 gal (17 L) Swing drive 2.3 qt (2.2 L) Final drive (each side) 2.2 qt (2.1 L) Cooling system 4.3 gal (16.2 L) electrical Voltage 24 Volts Alternator rating 50 amp Batteries 2 x 12 Volt Battery Reserve Capacity 92 Ah / 5 hour Work lights (4) 24 Volt / 70 watt (1 x boom; 1 x upper; 2 x cab) Swing mechanism Swing speed RPM Swing torque 24,400 lb ft (33,000 N m) Swing brake Mechanical disc undercarriage Length 12 ft 4 in (3.76 m) Track gauge 6 ft 6 in (1.99 m) Carrier rollers 2 per side Track rollers 7 per side Shoes triple grouser 47 per side Shoe width (std.) 23.6 in (600 mm) Link pitch 6.77 in (172 mm) Track: Chain Grease lubricated / strutted Guides Single Adjustment Hydraulic Ground Standard operating weight 4.79 psi (.33 bar) w/ 23.6 in (600 mm) triple semi-grouser shoes hydraulics System design Open center Main pumps Two variable displacement/ axial piston Max. rated flow: 2 x 34.1 GPM (2 x 129 L/min) System pressures: Boom, arm & bucket 4,970 psi (343 bar) Boom, arm & bucket w/ power boost 5,330 psi (368 bar) Travel circuits 4,970 psi (294 bar) Swing circuits 4,260 psi (343 bar) Pilot pump Max. capacity 1 x gear design 5.8 gpm (22 L/min) Controls With boom / arm holding valve Right track travel, Four-spool section bucket, boom and arm acceleration. Left track travel, Five-spool section auxiliary, swing, boom acceleration. Work mode selections SP: Speed priority H: Heavy duty A: Automatic Swing motor Swing final drive Travel motor Fixed displacement axial piston Planetary gear reduction Two-speed independent travel / axial piston hydraulic cylinders Boom cylinders Two (2) Cylinder bore 4.1 in (105 mm) Cylinder rod diameter 2.8 in (70 mm) Cylinder stroke 37.8 in (961 mm) Arm cylinder One (1) Cylinder bore 4.5 in (115 mm) Cylinder rod diameter 3.3 in (80 mm) Cylinder stroke 43.6 in (1108 mm) Bucket cylinder One (1) Cylinder bore 3.7 in (95 mm) Cylinder rod diameter 2.6 in (65 mm) Cylinder stroke 34.7 in (881 mm) Drivetrain Travel control Brakes Service brakes Two speed travel: Max. high speed Max. low speed Automatic downshift Drawbar pull Gradeability Dual stage relief/ counter balance design Mechanical disc SAHR disc (each motor) 3.5 mph (5.6 kph) 2.1 mph (3.4 kph) 25,900 lbf (115 kn) 70% (35 ) CAB and controls Air-conditioner output 18,100 BTU/hr Heater output 20,150 BTU/hr Sound level ISO6395 (inside cab) 70.0 dba Electrical outlet 12 Volt Cab interior light (1) 10 watt Rear-view camera (1) Standard Seat Air-suspension attachment Boom 15 ft 2 in (4.63 m) Arm 8 ft 2 in (2.5 m) Bucket digging force* 20,200 lbf (90 kn) w/ Auto Power-Boost 21,400 lbf (95 kn) *Digging force ratings based on ISO6015 operating weight Operating weight 28,600 lb ( kg) w/ shoes 23.6 in (600 mm) w/ boom 15 ft 2 in (4.63 m) w/ arm 8 ft 2 in (2.5 m) w/ bucket 880 lb (400 kg) w/ counterweight 4,850 lb (2200 kg) w/ operator / full fuel / standard equipment Page 1 of 7

2 CX130C LC Lift Capacities 8 ft 2 in (2.50 m) Arm Lift capacities calculated using a 900 lb (408 kg) bucket, 4,850 lb (2200 kg) counterweight. Load 5 ft 10 ft 15 ft 20 ft 25 ft MAXIMUM REACH (Lift (1.52 m) (3.05 m) (4.57 m) (6.1 m) (7.62 m) Point) END SIDE END SIDE END SIDE END SIDE END END SIDE Height +25 ft 4,050 lb* 4,050 lb* 16 ft 7 in 3,250 lb* 3,250 lb* (7.62 m) (1837 kg)* (1837 kg)* (5.05 m) (1474 kg)* (1474 kg)* +20 ft 5,900 lb* 5,900 lb* 4,950 lb* 4,750 lb 21 ft 9 in 2,700 lb* 2,700 lb* (6.1 m) (2676 kg)* (2676 kg)* (2245 kg)* (2155 kg) (6.63 m) (1225 kg)* (1225 kg)* +15 ft 6,400 lb* 6,400 lb* 6,100 lb* 4,700 lb 24 ft 7 in 2,550 lb* 2,550 lb* (4.57 m) (2903 kg)* (2903 kg)* (2767 kg)* (2132 kg) (7.49 m) (1157 kg)* (1157 kg)* +10 ft 11,550 lb* 11,550 lb* 8,600 lb* 7,250 lb 6,950 lb* 4,500 lb 4,750 lb 3,000 lb 26 ft 0 in 2,550 lb* 2,550 lb* (3.05) (5239 kg)* (5239 kg)* (3901 kg)* (3289 kg) (3152 kg)* (2041 kg) (2155 kg) (1361 kg) (7.92 m) (1157 kg)* (1157 kg)* +5 ft 16,800 lb* 12,700 lb 10,700 lb 6,700 lb 6,700 lb 4,250 lb 4,650 lb 2,850 lb 26 ft 4 in 2,700 lb* 2,600 lb (1.52 m) (7620 kg)* (5761 kg) (4853 kg) (3039 kg) (3039 kg) (1928 kg) (2109 kg) (1293 kg) (8.03 m) (1225 kg)* (1179 kg) Ground- 5,650 lb* 5,650 lb* 18,450 lb* 11,700 lb 10,300 lb 6,300 lb 6,500 lb 4,000 lb 4,550 lb 2,800 lb 25 ft 7 in 3,000 lb* 2,700 lb line (2563 kg)* (2563 kg)* (8369 kg)* (5307 kg) (4672 kg) (2858 kg) (2948 kg) (1814 kg) (2064 kg) (1270 kg) (7.80 m) (1361 kg)* (1225 kg) -5 ft 11,200 lb* 11,200 lb* 20,200 lb* 11,600 lb 10,100 lb 6,100 lb 6,350 lb 3,900 lb 23 ft 9 in 3,600 lb* 3,000 lb (-1.52 m) (5080 kg)* (5080 kg)* (9163 kg)* (5262 kg) (4581 kg) (2767 kg) (2880 kg) (1769 kg) (7.24 m) (1633 kg)* (1361 kg) -10 ft 17,700 lb* 17,700 lb* 18,550 lb* 11,850 lb 10,200 lb 6,200 lb 6,500 lb 4,050 lb 20 ft 7 in 4,900 lb* 3,850 lb (-3.05 m) (8029 kg)* (8029 kg)* (8414 kg)* (5375 kg) (4627 kg) (2812 kg) (2948 kg) (1837 kg) (6.27 m) (2223 kg)* (1746 kg) -15 ft 13,800 lb* 12,150 lb 8,250 lb* 6,450 lb 15 ft 4 in 7,800 lb* 6,200 lb (-4.57 m) (6260 kg)* (5511 kg) (3742 kg)* (2926 kg) (4.67 m) (3538 kg)* (2812 kg) 9 ft 10 in (3.01 m) Arm Lift capacities calculated using a 750 lb (340 kg) bucket, 4,850 lb (2200 kg) counterweight. Load 0 ft 5 ft 10 ft 15 ft 20 ft 25 ft MAXIMUM REACH (Lift (0 m) (1.52 m) (3.05 m) (4.57 m) (6.1 m) (7.62 m) Point) END SIDE END SIDE END SIDE END SIDE END SIDE END END SIDE Height +25 ft 19 ft 1 in 3,100 lb* 3,100 lb* (7.62 m) (5.82 m) (1406 kg)* (1406 kg)* +20 ft 4,900 lb* 4,900 lb* 23 ft 7 in 2,700 lb* 2,700 lb* (6.1 m) (2223 kg)* (2223 kg)* (7.19 m) (1225 kg)* (1225 kg)* +15 ft 5,800 lb* 4,850 lb 4,200 lb* 3,150 lb 26 ft 3 in 2,550 lb* 2,550 lb* (4.57 m) (2631 kg)* (2200 kg) (1905 kg)* (1429 kg) (8.00 m) (1157 kg)* (1157 kg)* +10 ft 7,500 lb* 7,300 lb 6,550 lb* 4,600 lb 4,850 lb 3,050 lb 27 ft 7 in 2,550 lb* 2,500 lb (3.05) (3402 kg)* (3311 kg) (2971 kg)* (2087 kg) (2200 kg) (1383 kg) (8.41 m) (1157 kg)* (1134 kg) +5 ft 14,450 lb* 13,100 lb 10,200 lb* 6,850 lb 6,800 lb 4,300 lb 4,700 lb 2,900 lb 27 ft 10 in 2,700 lb* 2,350 lb (1.52 m) (6554 kg)* (5942 kg) (4627 kg)* (3107 kg) (3084 kg) (1950 kg) (2132 kg) (1315 kg) (8.48 m) (1225 kg)* (1066 kg) Ground- 5,850 lb* 5,850 lb* 18,650 lb* 11,800 lb 10,350 lb 6,300 lb 6,500 lb 4,050 lb 4,550 lb 2,800 lb 27 ft 2 in 3,000 lb* 2,400 lb line (2654 kg)* (2654 kg)* (8459 kg)* (5352 kg) (4695 kg) (2858 kg) (2948 kg) (1837 kg) (2064 kg) (1270 kg) (8.28 m) (1361 kg)* (1089 kg) -5 ft 8,400 lb* 8,400 lb* 10,200 lb* 10,200 lb* 20,100 lb* 11,450 lb 10,050 lb 6,050 lb 6,350 lb 3,900 lb 4,500 lb 2,750 lb 25 ft 5 in 3,500 lb* 2,700 lb (-1.52 m) (3810 kg)* (3810 kg)* (4627 kg)* (4627 kg)* (9117 kg)* (5194 kg) (4559 kg) (2744 kg) (2880 kg) (1769 kg) (2041 kg) (1247 kg) (7.75 m) (1588 kg)* (1225 kg) -10 ft 11,200 lb* 11,200 lb* 15,100 lb* 15,100 lb* 19,300 lb* 11,600 lb 10,050 lb 6,100 lb 6,400 lb 3,950 lb 22 ft 6 in 4,600 lb* 3,300 lb (-3.05 m) (5080 kg)* (5080 kg)* (6849 kg)* (6849 kg)* (8754 kg)* (5262 kg) (4559 kg) (2767 kg) (2903 kg) (1792 kg) (6.86 m) (2087 kg)* (1497 kg) -15 ft 24,050 lb* 24,050 lb* 15,800 lb* 12,050 lb 10,150 lb 6,450 lb 17 ft 9 in 7,400 lb* 4,850 lb (-4.57 m) ( kg)* ( kg)* (7167 kg)* (5466 kg) (4604 kg) (2926 kg) (5.41 m) (3357 kg)* (2200 kg) NOTE: * Lift capacities do not exceed 75% of the minimum tipping load or 87% of the hydraulic lift capacity. Capacities that are marked with an asterisk are hydraulic limited. CX130C LC Page 2 of 7

3 CX130C LC Lift Capacities 6 ft 10 in (2.11 m) HD Arm Lift capacities calculated using a 900 lb (408 kg) bucket, 4,850 lb (2200 kg) counterweight. Load 5 ft 10 ft 15 ft 20 ft 25 ft MAXIMUM REACH (Lift (1.52 m) (3.05 m) (4.57 m) (6.1 m) (7.62 m) Point) END SIDE END SIDE END SIDE END SIDE END END SIDE Height +25 ft 14 ft 6 in 4,000 lb* 4,000 lb* (7.62 m) (4.42 m) (1814 kg)* (1814 kg)* +20 ft 6,300 lb* 6,300 lb* 4,050 lb* 4,050 lb* 20 ft 3 in 3,300 lb* 3,300 lb* (6.1 m) (2858 kg)* (2858 kg)* (1837 kg)* (1837 kg)* (6.17 m) (1497 kg)* (1497 kg)* +15 ft 7,150 lb* 7,150 lb* 6,550 lb* 4,550 lb 23 ft 4 in 3,050 lb* 3,050 lb* (4.57 m) (3243 kg)* (3243 kg)* (2971 kg)* (2064 kg) (7.11 m) (1383 kg)* (1383 kg)* +10 ft 12,350 lb* 12,350 lb* 9,250 lb* 7,050 lb 6,850 lb 4,350 lb 24 ft 10 in 3,050 lb* 2,900 lb (3.05) (5602 kg)* (5602 kg)* (4196 kg)* (3198 kg) (3107 kg) (1973 kg) (7.57 m) (1383 kg)* (1315 kg) +5 ft 17,400 lb* 12,250 lb 10,600 lb 6,550 lb 6,600 lb 4,150 lb 3,950 lb* 2,800 lb 25 ft 2 in 3,200 lb* 2,750 lb (1.52 m) (7893 kg)* (5557 kg) (4808 kg) (2971 kg) (2994 kg) (1882 kg) (1792 kg)* (1270 kg) (7.67 m) (1451 kg)* (1247 kg) Ground- 16,800 lb* 11,450 lb 10,150 lb 6,150 lb 6,400 lb 3,950 lb 24 ft 5 in 3,550 lb* 2,850 lb line (7620 kg)* (5194 kg) (4604 kg) (2790 kg) (2903 kg) (1792 kg) (7.44 m) (1610 kg)* (1293 kg) -5 ft 12,100 lb* 12,100 lb* 19,850 lb* 11,550 lb 10,050 lb 6,050 lb 6,350 lb 3,900 lb 22 ft 6 in 4,300 lb* 3,250 lb (-1.52 m) (5488 kg)* (5488 kg)* (9004 kg)* (5239 kg) (4559 kg) (2744 kg) (2880 kg) (1769 kg) (6.86 m) (1950 kg)* (1474 kg) -10 ft 18,600 lb* 18,600 lb* 17,500 lb* 11,850 lb 10,200 lb 6,250 lb 19 ft 1 in 6,000 lb* 4,300 lb (-3.05 m) (8437 kg)* (8437 kg)* (7938 kg)* (5375 kg) (4627 kg) (2835 kg) (5.82 m) (2722 kg)* (1950 kg) - 15 ft 11 ft 7 in 9,800 lb* 9,500 lb (-4.57 m) (3.53 m) (4445 kg) (4309 kg) NOTE: * Lift capacities do not exceed 75% of the minimum tipping load or 87% of the hydraulic lift capacity. Capacities that are marked with an asterisk are hydraulic limited. CX130C LC Page 3 of 7

4 C E M A B K L Line drawings are for illustrative purpose only and may not be exact representation of unit. J H F D G dimensions 8 ft 2 in (2.50 m) Arm 9 ft 10 in (3.01 m) Arm 6 ft 10 in (2.11 m) HD Arm A. Overall height (w/ attachment) 9 ft 3 in (2.83 m) 9 ft 3 in (2.83 m) 9 ft 3 in (2.83 m) B. Cab height 9 ft 3 in (2.83 m) 9 ft 3 in (2.83 m) 9 ft 3 in (2.83 m) C. Overall length (w/ attachment) 25 ft 0 in (7.62 m) 24 ft 10 in (7.61 m) 24 ft 10 in (7.61 m) D. Overall length (w/o attachment) 12 ft 9 in (3.88 m) 12 ft 9 in (3.88 m) 12 ft 9 in (3.88 m) E. Width of upperstructure 8 ft 3 in (2.54 m) 8 ft 3 in (2.54 m) 8 ft 3 in (2.54 m) F. Track overall length 12 ft 4 in (3.76 m) 12 ft 4 in (3.76 m) 12 ft 4 in (3.76 m) G. Track overall width w/ 23.6 in (600 mm) shoes 8 ft 5 in (2.59 m) 8 ft 5 in (2.59 m) 8 ft 5 in (2.59 m) H. Track shoe width 23.6 in (600 mm) 23.6 in (600 mm) 23.6 in (600 mm) J. Center to center (idler to sprocket) 9 ft 10 in (3.04 m) 9 ft 10 in (3.04 m) 9 ft 10 in (3.04 m) K. Upperstructure ground clearance 2 ft 10 in (0.90 m) 2 ft 10 in (0.90 m) 2 ft 10 in (0.90 m) L. Minimum ground clearance 17 in (0.44 m) 17 in (0.44 m) 17 in (0.44 m) M. Rear tail swing radius 6 ft 10 in (2.13 m) 6 ft 10 in (2.13 m) 6 ft 10 in (2.13 m) Operating weight* 28,600 lb ( kg) 28,741 lb ( kg) 28,459 lb ( kg) Ground pressure 4.79 psi (.33 bar) 4.79 psi (.33 bar) 4.79 psi (.33 bar) *With 23.6 in (600 mm) track shoe, 880 lb (400 kg) bucket, 165 lb (75 kg) operator, full fuel and standard equipment. CX130C LC Page 4 of 7

5 A B J G F E C D H 8 ft (2440 mm) performance specs 8 ft 2 in (2.50 m) Arm 9 ft 10 in (3.01 m) Arm 6 ft 10 in (2.11 m) HD Arm A. Maximum dig radius 27 ft 3 in (8.31 m) 28 ft 8 in (8.77 m) 26 ft 1 in (7.96 m) B. Dig radius at groundline 26 ft 8 in (8.17 m) 28 ft 4 in (8.64 m) 25 ft 6 in (7.81 m) C. Maximum dig depth 18 ft 2 in (5.54 m) 19 ft 9 in (6.05 m) 16 ft 9 in (5.15 m) D. Dig depth 8 ft 0 in (2.44 m) level bottom 17 ft 5 in (5.33 m) 19 ft 3 in (5.87 m) 16 ft 11 in (4.91 m) E. Dump height 20 ft 10 in (6.39 m) 21 ft 9 in (6.68 m) 20 ft 2 in (6.17 m) F. Maximum reach height 28 ft 8 in (8.77 m) 29 ft 7 in (9.05 m) 28 ft 1 in (8.55 m) G. Bucket rotation H. Maximum vertical wall dig depth 17 ft 5 in (5.33 m) 19 ft 3 in (5.87 m) 15 ft 1 in (4.60 m) J. Minimum swing radius 7 ft 7 in (2.34 m) 8 ft 7 in (2.66 m) 7 ft 7 in (2.36 m) Arm digging force: Standard 13,900 lb (62.0 kn) 12,600 lb (56.0 kn) 15,700 lb (70.0 kn) Power Boost 14,800 lb (66.0 kn) 13,500 lb (60.0 kn) 16,600 lb (74.0 kn) Bucket digging force: Standard 20,200 lb (90.0 kn) 20,200 lb (90.0 kn) 20,200 lb (90.0 kn) Power Boost 21,400 lb (95.0 kn) 21,400 lb (95.0 kn) 21,400 lb (95.0 kn) CX130C LC Page 5 of 7

6 Standard equipment ENGINE Isuzu four-cylinder turbo-charged diesel Certified Tier 4 Interim (CEGR) Electronic fuel injection High pressure common rail system Diesel Particulate Defuser system (DPD) Neutral safety start Auto-engine warm up Glow-plug pre-heat EPF (Engine Protection Feature) Dual-stage fuel filtration Dual element air filter Remote oil filter Green plug oil drain 500-hour engine oil change interval 24-volt system Requires CJ-4 engine oil Requires ultra low-sulfur fuel FUEL ECONOMY SYSTEMS Engine idle / Fuel economy system: Auto-idle One-touch idle Idle shut-down BEC boom economy control AEC auto economy control SWC swing relief control SSC spool stroke control HYDRAULICS Auto power boost Auto swing priority Auto travel speed change HYDRAULICS (continued) Selectable work modes ISO pattern controls Pre-set auxiliary pump settings Auxiliary valve 5,000-hour hydraulic oil change interval 1,000-hour hydraulic filter change interval SAHR brake UPPERSTRUCTURE Right and left side mirrors Isolation mounted cab (fluid and spring) Common key vandal locks Upper mounted work light (70 watt) Swivel guard belly pan UNDERCARRIAGE 23.6 in (600 mm) steel shoes, triple semi-grouser Full overlap turntable bearing tub Hydraulic track adjustment X-pattern carbody ATTACHMENT Boom 15 ft 2 in (4.63 m) Arm 8 ft 2 in (2.50 m) Heavy-duty bucket linkage Boom mounted work light (70 watt) Auxiliary pipe brackets Centralized grease fittings Attachment cushion valve Arm and boom regeneration OPERATOR STATION ROPS protection FOPS cab top guard (Level 1) Pressurized cab One-touch lock front window AC / heat / defrost w/ auto climate control Color monitor (7 in / 180 mm) Interior dome light Air-suspension seat (cloth) Seatbelt (3 in) Adjustable armrests Tiltng consoles 4-position Low-effort joystick controls Sliding cockpit (7 in / 180 mm) Straight travel AM/FM radio w/ antenna and 2 speakers Aux-in port for personal electronics Rear-view camera Anti-theft system (start code system) Rubber floormat 12-volt electric socket 24-volt cigarette lighter External rearview mirrors Windshield wiper / washer Clear (polycarbonate) roof window w/ sunshade Cup holder Storage compartments On-board diagnostic system Travel alarm with cancel switch One key start & lock-up optional equipment HYDRAULICS Auxiliary hydraulics: Single acting / joystick activated Double acting / joystick activated Multi-function / joystick activated Secondary low-flow / joystick activated ATTACHMENT Standard arm 9 ft 10 in (3.01 m) Heavy-duty arm 6 ft 10 in (2.11 m) Coupler / Case multi-pin grabber Buckets: Heavy duty Extreme duty Load holding control Free swing (order kit through Service Parts) Hose Burst Check Valve (HBCV) OPERATOR STATION Control pattern selector FOPS cab top guard (Level 2) Front grill guard 2 x 2 screen mesh Front rock guard vertical bars (two piece) / OPG 1 Front rock guard vertical bars (fixed / one piece) / OPG 2 Vandal guard Rain deflector Sun visor Side-view camera Refueling pump UNDERCARRIAGE 23.6 in (600 mm) steel shoes, triple semi-grouser 27.6 in (700 mm) steel shoes, triple semi-grouser 20.0 in (500 mm) rubber shoes Double track chain guides BUCKETS Application Width SAE Heaped Capacity Heavy-duty 18 in to 48 in (0.46 m to 1.22 m) 0.32 yd 3 to 0.96 yd 3 (0.25 m 3 to 0.74 m 3 ) High capacity heavy-duty 18 in to 48 in (0.46 m to 1.22 m) 0.36 yd 3 to 1.12 yd 3 (0.28 m 3 to 0.86 m 3 ) Coupler 18 in to 48 in (0.46 m to 1.22 m) 0.32 yd 3 to 0.96 yd 3 (0.25 m 3 to 0.74 m 3 ) Ditching 48 in or 60 in (1.22 m or 1.52 m) 0.79 yd 3 or 1.02 yd 3 (0.60 m 3 or 0.78 m 3 ) CX130C LC Page 6 of 7

7 This page intentionally left blank. NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. NOTE: All engines meet current EPA emissions requirements. IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Case Construction Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. Form No. CCE201203CX130CLC Printed in U.S.A CNH America LLC Replaces form no. CCE201105CX130B CX130C LC Page 7 of 7 All Rights Reserved All Case construction equipment is biodiesel ready.

8 CX130C CX160C EXCAVATORS

9 CX130C/CX160C Excavators MORE DIRT MOVED. LESS FUEL USED. The CASE CX130C and CX160C excavators combine the muscle and finesse that s required to get the job done as effectively and efficiently as possible. These versatile machines provide auxiliary customization, craning strength and the power to keep your project moving forward. And they do so without burning excess fuel or sacrificing precision and comfort. Greater control means fewer jolts and jerks from the attachment. Smart systems allow fewer fill-ups and more jobs done. That s how CASE does it.

10 CX130C CX160C Highlights Tier 4 Interim Certified Engine CEGR with diesel particulate filter. CASE Intelligent Hydraulic System By blending four integrated hydraulic control systems throughout lift/dump and dig/curl movements, CASE excavators can move more dirt per gallon and load more trucks per shift. Boom Economy Control (BEC) Auto Economy Control (AEC) Swing Relief Control (SWC) Spool Stroke Control (SSC) Intelligent hydraulic systems matched with engine controllers to maximize speed and efficiency of the machine while reducing fuel consumption for unnecessary and energy wasting functionality. Unmatched featherability provides the operator with smoother control of the attachment without the undesired jerks or shakes like some competitors. 3 Power Modes (Speed Priority, Heavy and Automatic) provide selectable operation capacity matched to the jobsite needs. Isomount cab cushioning system provides less noise and vibration transfer to the operator s station. Easy Maintenance System (EMS) lubrication joints. New full-color 7-inch HD monitor. Standard rear and optional side cameras with side-byside viewing in the monitor provide increased awareness around the jobsite. Best-in-Class Operator Environment Climb inside a ROPS/FOPS certified cab with spacious, climate-controlled comfort and smart operation features: Sunlight sensor, auto climate management, removable front windows and optional sun visor and rain deflectors. Highly adjustable seat with independent arm rest, seat and pedestal movements. Floor-to-ceiling glass on sides and front provide excellent visibility to the worksite. Low operating noise which reduces operator fatigue and promotes awareness around the jobsite. Optional CASE Multi Fit Coupler provides versatility between attachments for increased utilization.

11 CX130C CX160C EXCAVATORS CX130C A C F D Line drawings are for illustrative purpose only and may not be exact representation of unit. L DIMENSIONS CX130C CX130C with Dozer Blade CX160C A. Overall Height With Attachment 9 ft. 3 in. (2.83 m) 9 ft. 3 in. (2.83 m) 9 ft. 8 in. (2.98 m) B. Cab Height 9 ft. 3 in. (2.83 m) 9 ft. 3 in. (2.83 m) 9 ft. 8 in. (2.98 m) C. Overall Length With Attachment 25 ft. 0 in. (7.62 m) 25 ft. 0 in. (7.62 m) 27 ft. 7 in. (8.44 m) D. Overall Length Without Attachment 12 ft. 9 in. (3.88 m) 13 ft. 9 in. (4.18 m) 14 ft. 5 in. (4.41 m) E. Width Of Upperstructure 8 ft. 3 in. (2.54 m) 8 ft. 3 in. (2.54 m) 8 ft. 3 in. (2.54 m) F. Track Overall Length 11 ft. 6 in. (3.50 m) 11 ft. 6 in. (3.50 m) 13 ft. 1 in. (3.99 m) G. Track Overall Width 8 ft. 5 in. (2.59 m) 8 ft. 5 in. (2.59 m) 8 ft. 5 in. (2.59 m) H. Track Shoe Width 23.6 in. (0.60 m) 23.6 in. (0.60 m) 23.6 in. (0.60 m) J. Upperstructure Ground Clearance 2 ft. 10 in. (0.90 m) 2 ft. 10 in. (0.90 m) 3 ft. 4 in. (1.02 m) K. Minimum Ground Clearance 17 in. (0.44 m) 17 in. (0.44 m) 17 in. (0.44 m) L. Rear Tail Swing Radius 7 ft. 0 in. (2.13 m) 7 ft. 0 in. (2.13 m) 8 ft. 0 in. (2.45 m) J B H E G K Protected by ProCare The CX130C and CX160C come standard with the industry s first all-in-one heavy machine support program that s as powerful as the equipment it protects CASE ProCare. ProCare includes: 3-year/3000-hr. Full-Machine Factory Warranty *. We ve got your back for up to three full years! 3-year/3000-hr. Planned Maintenance. Don t spend another dime for scheduled care from factory-trained CASE technicians. 3-year SiteWatch Subscription. Telematics isn t a luxury, it s a necessity and we ve made it accessible to all. *See your dealer for the complete terms of CNH s Warranty and Limitation of Liability, which contains certain limits and exclusions. SPECIFICATIONS CX130C CX130C with Dozer Blade CX160C Engine Isuzu AM-4JJ1X Isuzu AM-4JJ1X Isuzu AM-4JJ1X Emissions Rating Tier 4 Interim (Cooled EGR) Tier 4 Interim (Cooled EGR) Tier 4 Interim (Cooled EGR) Displacement in. 3 (L) 183 (3.0) 183 (3.0) 183 (3.0) Cylinders 4-cylinder in line 4-cylinder in line 4-cylinder in line Net hp (kw) RPM RPM RPM Swing Speed RPM Bucket Digging Force lb. (kn) 21,400 (95.0) 21,400 (95.0) 26,500 (118.0) Arm Digging Force lb. (kn) 14,800 (66.0) 14,800 (66.0) 18,800 (84.0) Operating Weight lb. (kg) 27,100 (12 200) 30,000 (13 608) 38,001 (17 200) Max. Dig Ground Line 27 ft. 3 in. (8.37 m) 27 ft. 3 in. (8.37 m) 29 ft. 7 in. (9.04 m) Max. Digging Depth 18 ft. 2 in. (5.54 m) 18 ft. 2 in. (5.54 m) 19 ft. 9 in. (6.06 m) Swing Torque lb. ft. (N m) 23,340 (33 000) 23,340 (33 000) 33,300 (45 100) Drawbar Pull lb. (kn) 26,078 (116) 26,078 (116) 36,200 (161) NOTE: Specifications are based on standard arm for each machine: CX130C 8 ft. 2 in. (2.50 m); CX160C 8 ft. 7 in. (2.62 m). SmartFit Bucket Teeth. CX130C and CX160C buckets come standard with the innovative SmartFit bucket tooth system. These heavy-duty, self-sharpening teeth combine exceptional strength and unmatched ease of installation thanks to a hammerless fastener system with reusable locking pins. Available in a full range of styles CNH America LLC. All rights reserved. CASE is a registered trademark and SiteWatch is a trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. Printed in U.S.A. Form No. CCE201311CX130C_160C Always read the operator s manual before operating any equipment. Inspect equipment before using it, and be sure it is operating properly. Follow the product safety signs and use any safety features provided. All engines meet current EPA emission regulations. All specifications are stated in accordance with SAE standards or recommended practices, where applicable. Contains 10% post-consumer fiber IMPORTANT: CASE Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Availability of some models and equipment builds vary according to the country in which the equipment is used. The illustrations and text may include optional equipment and accessories and may not include all standard equipment. Your CASE dealer/distributor will be able to give you details of the products and their specifications available in your area. CASE construction equipment is biodiesel friendly.

CX130C. Swing mechanism. Swing torque 24,400 lb ft (33,000 N m) Length 12 ft 4 in (3.76 m) Track gauge 6 ft 6 in (1.99 m)

CX130C. Swing mechanism. Swing torque 24,400 lb ft (33,000 N m) Length 12 ft 4 in (3.76 m) Track gauge 6 ft 6 in (1.99 m) CX130C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED engine Model Isuzu AM-4JJ1X, Tier 4 Interim Certified (Cooled EGR) Fuel Type Cylinders Requires ultra low-sulfur fuel B5 biodiesel tolerant

More information

CX210C EXCAVATOR. Swing mechanism. Length 14 ft 8 in (4.47 m) Track gauge 7 ft 10 in (2.4 m) Track Grease lubricated / strutted

CX210C EXCAVATOR. Swing mechanism. Length 14 ft 8 in (4.47 m) Track gauge 7 ft 10 in (2.4 m) Track Grease lubricated / strutted CX210C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED engine Model Fuel Type Cylinders Isuzu AM-4HK1X Tier 4 Interim Certified (Cooled EGR) Requires ultra low-sulfur fuel B5 biodiesel tolerant

More information

CX130C OPERATOR ENVIRONMENT. Sound level ISO6395 inside cab 70 dba Electrical outlet Cab interior light (1) Rear-view camera (1) Air-suspension

CX130C OPERATOR ENVIRONMENT. Sound level ISO6395 inside cab 70 dba Electrical outlet Cab interior light (1) Rear-view camera (1) Air-suspension CX130C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED ENGINE Model Emissions Certification Fuel Isuzu AM-4JJ1X, Cooled EGR Tier 4 Interim Requires ultra low-sulfur fuel B5 biodiesel tolerant

More information

CX160C OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light

CX160C OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light CX160C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AM-4JJ1X Cooled EGR Tier 4 Interim Requires ultra low-sulfur fuel B5 biodiesel

More information

CX250C CAB AND CONTROLS. Sound level inside cab ISO dba Electrical outlet Cab interior light. Air-suspension

CX250C CAB AND CONTROLS. Sound level inside cab ISO dba Electrical outlet Cab interior light. Air-suspension CX250C EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 INTERIM CERTIFIED ENGINE Model Emissions Certification Fuel Isuzu AM-4HK1X Cooled EGR Tier 4 Interim Requires ultra-low sulfur fuel B5 biodiesel tolerant

More information

CX300C EXCAVATOR CAB AND CONTROLS. Sound level inside cab ISO6395 Electrical outlet Cab interior light. 20 ft 2 in (6 150 mm)

CX300C EXCAVATOR CAB AND CONTROLS. Sound level inside cab ISO6395 Electrical outlet Cab interior light. 20 ft 2 in (6 150 mm) CX300C EXCAVATOR TIER 4 INTERIM CERTIFIED ENGINE Model Emissions Certification Fuel Isuzu AM-6HK1X Cooled EGR Tier 4 Interim Requires ultra low-sulfur fuel B5 biodiesel tolerant Type Water-cooled, 4-cycle,

More information

CX145D SR SHORT RADIUS EXCAVATOR TIER 4 FINAL

CX145D SR SHORT RADIUS EXCAVATOR TIER 4 FINAL SHORT RADIUS EXCAVATOR TIER 4 FINAL ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AM-4JJ1X CEGR, SCR and DOC Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant Water-cooled,

More information

CX145D SR SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED

CX145D SR SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED CX145D SR SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AM-4JJ1X CEGR, SCR and DOC Tier 4 Final Requires ultra low-sulfur fuel

More information

CX80C EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED

CX80C EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED CX80C EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AP-4LE2X Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant Water-cooled,

More information

CX75C OPERATOR ENVIRONMENT

CX75C OPERATOR ENVIRONMENT CX75C MSR EXCAVATOR STANDARD & OFFSET BOOM TIER 4 FINAL CERTIFIED PRELIMINARY ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AP-4LE2X Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel

More information

CX80C OPERATOR ENVIRONMENT

CX80C OPERATOR ENVIRONMENT CX80C EXCAVATOR SWING BOOM TIER 4 FINAL CERTIFIED PRELIMINARY ENGINE Model Type Cylinders Isuzu AP-4LE2X, Tier 4 Final Certified Water-cooled, 4-cycle. Turbo-charged w/ air-cooled intercooler w/ DOC 4-cylinder

More information

CX245D SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED

CX245D SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED CX245D SHORT RADIUS EXCAVATOR DOZER BLADE TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Isuzu AR-4HK1X Turbocharged w/cooled intercooler/ SCR System Tier 4 Final Requires ultra low-sulfur

More information

CX245D SHORT RADIUS EXCAVATOR TIER 4 FINAL CERTIFIED

CX245D SHORT RADIUS EXCAVATOR TIER 4 FINAL CERTIFIED CX245D SHORT RADIUS EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Isuzu AR-4HK1X Turbocharged w/cooled intercooler/ SCR System Tier 4 Final Requires ultra low-sulfur fuel B5

More information

EXCAVATOR STANDARD & DOZER BLADE EQUIPPED TIER 3 CERTIFIED

EXCAVATOR STANDARD & DOZER BLADE EQUIPPED TIER 3 CERTIFIED CX225 MSR EXCAVATOR STANDARD & DOZER BLADE EQUIPPED TIER 3 CERTIFIED ENGINE Model Type Isuzu AI-4HK1X, Tier 3 certified 4-stroke, turbocharged Cylinders 4 Displacement Bore/Stroke Fuel injection Fuel filter

More information

CX130D EXCAVATOR BLADE TIER 4 FINAL CERTIFIED

CX130D EXCAVATOR BLADE TIER 4 FINAL CERTIFIED EXCAVATOR BLADE TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AR-4JJ1X CEGR, SCR, DOC Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel tolerant Water-cooled,

More information

CX160D EXCAVATOR LONG UNDERCARRIAGE TIER 4 FINAL CERTIFIED

CX160D EXCAVATOR LONG UNDERCARRIAGE TIER 4 FINAL CERTIFIED CX160D EXCAVATOR LONG UNDERCARRIAGE TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AR-4JJ1X CEGR, SCR, DOC Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel

More information

CX350D LR EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED

CX350D LR EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-6HK1X Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel tolerant Water-cooled, 4-cycle

More information

CX210D LR EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED

CX210D LR EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED PRELIMINARY CX210D LR EXCAVATOR LONG REACH TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AR-4HK1X Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel tolerant

More information

CX250D LONG REACH EXCAVATOR (LR) LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED

CX250D LONG REACH EXCAVATOR (LR) LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED CX250D LONG REACH EXCAVATOR (LR) LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-4HK1X Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel

More information

CX750D MASS EXCAVATOR TIER 4 FINAL CERTIFIED

CX750D MASS EXCAVATOR TIER 4 FINAL CERTIFIED PRELIMINARY CX750D MASS EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-6WG1X Cooled EGR Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant

More information

CX135. Variable displacement axial piston design

CX135. Variable displacement axial piston design CX135 EXCAVATOR TIER III CERTIFIED ENGINE Model Type Isuzu AJ-4JJ1X, Tier III certified 4-stroke, turbocharged Cylinders 4 Bore/Stroke Displacement Fuel injection Fuel injection pump Fuel Fuel filter Cooling

More information

CX750D EXCAVATOR TIER 4 FINAL CERTIFIED

CX750D EXCAVATOR TIER 4 FINAL CERTIFIED PRELIMINARY CX750D EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-6WG1X Cooled EGR Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant

More information

Number of rollers Top, each track 1 Bottom, each track 5 Number of shoes Triple grouser each side 39. Gradeability 70%

Number of rollers Top, each track 1 Bottom, each track 5 Number of shoes Triple grouser each side 39. Gradeability 70% CX75 EXCAVATOR TIER III CERTIFIED ENGINE Model Isuzu AU-4LE2X,Tier III certified Type 4-stroke turbocharged Cylinders 4 Bore/Stroke 3.35 in x 3.78 in (85 x 96 mm) Displacement 133 in 3 (2179 cc) Fuel injection

More information

CX250D OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light

CX250D OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light CX250D EXCAVATOR LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-4HK1X Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel tolerant

More information

CX290D EXCAVATOR MATERIAL HANDLER TIER 4 FINAL CERTIFIED

CX290D EXCAVATOR MATERIAL HANDLER TIER 4 FINAL CERTIFIED CX290D EXCAVATOR MATERIAL HANDLER TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-4HK1X Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel tolerant Water-cooled,

More information

Number of rollers Top, each track 3 Bottom, each track 8 Number of shoes Double grouser each side 47. Variable displacement axial piston design

Number of rollers Top, each track 3 Bottom, each track 8 Number of shoes Double grouser each side 47. Variable displacement axial piston design CX700B EXCAVATOR TIER III CERTIFIED ENGINE Model Type AH-6WG1XYSS, Tier III certified 4-stroke, turbocharged Cylinders 6 Bore/Stroke Displacement 5.79 in x 6.07 in (147 x 154 mm) 957 in 3 (15 700 cc) Grade

More information

CX800B EXCAVATOR. Number of rollers Top, each track 3 Bottom, each track 9 Number of shoes Double grouser each side 51

CX800B EXCAVATOR. Number of rollers Top, each track 3 Bottom, each track 9 Number of shoes Double grouser each side 51 CX800B EXCAVATOR TIER III CERTIFIED ENGINE Model Type AH-6WG1XYSS, Tier III certified 4-stroke, turbocharged Cylinders 6 Bore/ Displacement Fuel injection Fuel Fuel filter Cooling Horsepower per SAE J1349

More information

CX350D OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light

CX350D OPERATOR ENVIRONMENT. Sound level inside cab ISO dba Electrical outlet Cab interior light CX350D EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-6HK1X Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant Water-cooled, 4-cycle,

More information

CX210D STD LC EXCAVATOR STANDARD LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED

CX210D STD LC EXCAVATOR STANDARD LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED STD LC EXCAVATOR STANDARD LONG UNDERCARRIAGE (LC) TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AR-4HK1X Tier 4 Final Requires ultra-low sulfur fuel B5 biodiesel

More information

CX300D EXCAVATOR TIER 4 FINAL CERTIFIED

CX300D EXCAVATOR TIER 4 FINAL CERTIFIED CX300D EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Fuel Type Cylinders Isuzu AQ-6HK1X Tier 4 Final Requires ultra low-sulfur fuel B5 biodiesel tolerant Water-cooled, 4-cycle diesel,

More information

C-SERIES HYDRAULIC EXCAVATORS CX235C SR COMPACT PERFORMANCE. EXPERTS FOR THE REAL WORLD SINCE 1842

C-SERIES HYDRAULIC EXCAVATORS CX235C SR COMPACT PERFORMANCE.   EXPERTS FOR THE REAL WORLD SINCE 1842 C-SERIES HYDRAULIC EXCAVATORS CX235C SR COMPACT PERFORMANCE www.casece.com EXPERTS FOR THE REAL WORLD SINCE 1842 MAIN REASONS TO CHOOSE THE C-SERIES HIGH EFFICIENCY CASE Intelligent Hydraulic System (CIHS),

More information

Lubricant and Coolant Capacity

Lubricant and Coolant Capacity Engine Isuzu AI-4HK1X Tier 3 turbocharged diesel engine with electronic fuel control, 153 Net HP (114 kw), 5.2 Liter displacement, 4-cylinder, water-cooled, EGR with cooler, air-toair intercooler, 24-volt

More information

Lubricant and Coolant Capacity

Lubricant and Coolant Capacity Operating Weight: 28,440 (12,900 kg) SAE Net Horsepower: 95 HP (71 kw) Bucket Range:.42 -.98 yd 3 (.32 -.75 m 3 ) Engine Isuzu AJ-4JJ1X Tier 3 turbocharged diesel engine with electronic fuel control, 4-cylinder,

More information

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (22.8 L/min) Relief pressure psi (3.

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (22.8 L/min) Relief pressure psi (3. CX130 Excavator ENGINE Model... Case 4TA-390 Type... 4-stroke, turbocharged and aftercooled Cylinders... 4 Bore/Stroke... 4.02 x 4.72 (102 x 120 mm) Displacement... 239 in 3 (3.9 L) Fuel injection... Direct

More information

Undercarriage. Lubricant and Coolant Capacity. Travel System

Undercarriage. Lubricant and Coolant Capacity. Travel System MATERIAL HANDLER Operating Weight: 76,49 lbs (8, kg) SAE Net Horsepower: with fan pump 49 HP (69 kw) without fan pump HP (97 kw) Swing Torque: 96,6 lbf-ft. (66. kn m) Engine Isuzu AH-6WGXYSS- Tier turbocharged

More information

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (20 L/min) Relief pressure psi (3900 kpa)

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (20 L/min) Relief pressure psi (3900 kpa) 9010B Excavator ENGINE Model... Case 4TA-390 Type... 4-stroke, turbocharged and aftercooled Cylinders... 4 Bore/Stroke... 4.02 x 4.72 (102 x 120 mm) Displacement... 239 in 3 (3.9 L) Fuel injection... Direct

More information

Lubricant and Coolant Capacity

Lubricant and Coolant Capacity Operating Weight: 105,600 lbs (47,900 kg) SAE Net Horsepower: with fan pump 329 HP (245 kw) without fan pump 362 HP (270 kw) Range: 1.58-4.05 yd 3 (1.21-3.10 m 3 ) Engine Isuzu AH-6UZ1XYSS Tier 3 turbocharged

More information

Hydraulic System. (130 mm x 80 mm x 260 mm) Swing

Hydraulic System. (130 mm x 80 mm x 260 mm) Swing SAE Net Horsepower: 160 HP (119 kw) Operating Weight: 56,879 lbs. (25 800 kg) Digging Depth: 21 ft. 10 in. (6.65 m) Engine Hydraulic System Travel System Isuzu AM-4HK1X Tier 4A turbocharged diesel engine

More information

750M. (2) 12-volt, low-maintenance 925 cold-cranking -4 F (-20 C) OPERATOR ENVIRONMENT

750M. (2) 12-volt, low-maintenance 925 cold-cranking -4 F (-20 C) OPERATOR ENVIRONMENT 750M LT/WT/LGP CRAWLER DOZER TIER 4 INTERIM CERTIFIED ENGINE Model FPT F5HFL413J Tier 4 Interim Certified Cylinders 4 Displacement 207.5 in 3 (3.4 L) Fuel injection Common rail Fuel #2 Diesel Fuel filter

More information

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (21 L/min) Relief pressure psi (3900 kpa)

HYDRAULICS. Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (21 L/min) Relief pressure psi (3900 kpa) 9020B Excavator ENGINE Model... Case 4TA-390 Type... 4-stroke, turbocharged and aftercooled Cylinders... 4 Bore/Stroke... 4.02 x 4.72 (102 x 120 mm) Displacement... 239 in 3 (3.9 L ) Fuel injection...

More information

Lubricant and Coolant Capacity

Lubricant and Coolant Capacity Operating Weight: 105,600 lbs (47,900 kg) SAE Net Horsepower: with fan pump 329 HP (245 kw) without fan pump 362 HP (270 kw) Range: 1.58-4.05 yd 3 (1.21-3.10 m 3 ) Engine Isuzu AH-6UZ1XYSS Tier 3 turbocharged

More information

Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (21 L/min) Relief pressure psi (3900 kpa)

Pilot control hydraulic system Pump (1)... Gear design Maximum capacity gpm (21 L/min) Relief pressure psi (3900 kpa) 9020B Excavator ENGINE Model... Case 4TA-390 Type... 4-stroke, turbocharged and aftercooled Cylinders... 4 Bore/Stroke... 4.02 x 4.72 (102 x 120 mm) Displacement... 239 in 3 (3.9 L ) Fuel injection...

More information

850M. (2) 12-volt, low-maintenance 925 cold-cranking -4 F (-20 C) OPERATOR ENVIRONMENT

850M. (2) 12-volt, low-maintenance 925 cold-cranking -4 F (-20 C) OPERATOR ENVIRONMENT 850M LT/WT/LGP CRAWLER DOZER TIER 4 INTERIM CERTIFIED ENGINE Model FPT F4HFE413P Tier 4 Interim Certified Cylinders 4 Displacement 275 in 3 (4.5 L) Fuel injection Common rail Fuel #2 Diesel Fuel filter

More information

CX55BMTS OPERATING WEIGHT. Cab with 165 lb (75 kg) operator, 247 lb (112 kg) bucket, full fuel and standard equipment: 11,312 lb (5 130 kg)

CX55BMTS OPERATING WEIGHT. Cab with 165 lb (75 kg) operator, 247 lb (112 kg) bucket, full fuel and standard equipment: 11,312 lb (5 130 kg) CX55BMTS COMPACT EXCAVATOR TIER 4 FINAL CERTIFIED ENGINE Model Yanmar 4TNV88-C-PYB Tier 4 Final Certified Cylinders 4 Bore/ 3.46 x 3.54 in (88 x 90 mm) Displacement 133.6 in 3 (2.2 L) Fuel injection Direct

More information

CONSTRUCTION EQUIPMENT

CONSTRUCTION EQUIPMENT CONSTRUCTION EQUIPMENT U.S. PRICE LIST EXCAVATORS PL-200 CX SAP REVISION 13b EFFECTIVE MAY 13, 2013 REVISED JUNE 20, 2013 THIS IS AN ELECTRONIC COPY ONLY HARD COPIES WILL NOT BE DISTRIBUTED. This price

More information

CX17BCOMPACT EXCAVATOR

CX17BCOMPACT EXCAVATOR CX17BCOMPACT EXCAVATOR ENGINE Model Mitsubishi L3E-W231KBS Cylinders 3 Bore/Stroke Displacement Fuel injection Fuel injection pump Fuel Fuel filter Cooling 2.99 in x 2.76 in (76 x 70 mm) 58.1 in 3 (952

More information

DX140LC TECHNICAL DATA

DX140LC TECHNICAL DATA DX140LC TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL Doosan DL06 Diesel, Tier III Certified NUMBER OF CYLINDERS 6 RATED FLYWHEEL POWER hp / rpm 98.6 / 1,850 (hp PER SAE J1995) GROSS

More information

ZAXIS DASH-5 Ultrashort-CLASS EXCAVATORS ZX245LC kw (159 hp)

ZAXIS DASH-5 Ultrashort-CLASS EXCAVATORS ZX245LC kw (159 hp) ZAXIS DASH-5 Ultrashort-CLASS EXCAVATORS ZX245LC-5 119 kw (159 hp) ZX245LC-5 ZAXIS DASH-5 Ultrashort-CLASS EXCAVATORS Engine ZX245LC-5 Manufacturer and Model Isuzu 4HK1 Non-Road Emissions Standard EPA

More information

DX420LC TECHNICAL DATA

DX420LC TECHNICAL DATA DX420LC TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL Doosan DV11 Diesel, Tier III Certified NUMBER OF CYLINDERS 6 RATED FLYWHEEL POWER hp / rpm 293 / 1,800 (hp PER SAE J1995) GROSS kw

More information

2050M. Transmission cooling: Tube and fin Core size in 2 (0.33 m 2 ) (2) 12-volt, low-maintenance 950 cold-cranking 0 F (-18 C)

2050M. Transmission cooling: Tube and fin Core size in 2 (0.33 m 2 ) (2) 12-volt, low-maintenance 950 cold-cranking 0 F (-18 C) 2050M LT/XLT/WT/LGP CRAWLER DOZER TIER 4 INTERIM CERTIFIED ENGINE Model FPT F4HFE613J Tier 4 Interim Certified Cylinders 6 Displacement 409 in 3 (6.7 L) Fuel injection Fuel Fuel filter Air intake Direct

More information

CONTROL. No. of shoes on each side No. of carrier roller on each side No. of track roller on each side No. of rail guard on each side.

CONTROL. No. of shoes on each side No. of carrier roller on each side No. of track roller on each side No. of rail guard on each side. SPECIFICATIONS ENGINE Maker / Model Type Rated flywheel horse power SAE DIN Perkins 1204F Water-cooled, 4-cycle diesel, 4-cylinder inline, Direct injection, Turbocharged, Charge and air cooled J1995 (gross)

More information

FORESTRY. For Use in Log-Loading, Road Building and Harvester Processing Applications. Engine. Cab and Controls. Undercarriage

FORESTRY. For Use in Log-Loading, Road Building and Harvester Processing Applications. Engine. Cab and Controls. Undercarriage FORESTRY For Use in Log-Loading, Road Building and Harvester Processing Applications Engine Isuzu AI-4HK1X Tier 3 turbocharged diesel engine with electronic fuel control, 4-cylinder, water-cooled, EGR

More information

EC140B LC VOLVO EXCAVATOR

EC140B LC VOLVO EXCAVATOR VOLVO EXCAVATOR EC140B LC Engine power, gross: 73 kw 98 hp Operating weight: 13.4 ~ 15.2 t 29,529 ~ 33,450 lb Buckets (SAE): 600 ~ 975 l 0.78 ~ 1.28 yd 3 Turbocharged Volvo diesel engine with direct injection

More information

CX210C HYDRAULIC EXCAVATOR HYDRAULIC SYSTEM HYDRAULIC CONTROLS ENGINE MONITOR SYSTEM ELECTRICAL SYSTEM

CX210C HYDRAULIC EXCAVATOR HYDRAULIC SYSTEM HYDRAULIC CONTROLS ENGINE MONITOR SYSTEM ELECTRICAL SYSTEM CX210C HYDRAULIC EXCAVATOR ENGINE Brand Model Type ISUZU GI-4HK1X 4-stroke engine, water-cooled, 4 cylinder common rail injection system, turbocharged with air-cooled intercooler, with tier 3 emission

More information

With Tier 4 Interim Engine installed HYUNDAI HEAVY INDUSTRIES

With Tier 4 Interim Engine installed HYUNDAI HEAVY INDUSTRIES With Tier 4 Interim Engine installed HYUNDAI HEAVY INDUSTRIES 1 Specifications R145LCR-9A ENGINE MODEL Type PERKINS 1204E Water cooled, 4 cycle Diesel, 4-Cylinders in line, direct injection, turbocharged,

More information

CONSTRUCTION EQUIPMENT

CONSTRUCTION EQUIPMENT CONSTRUCTION EQUIPMENT U.S. PRICE LIST EXCAVATORS PL-200 CX SAP REVISION 17 EFFECTIVE FEBRUARY 9, 2015 THIS IS AN ELECTRONIC COPY ONLY HARD COPIES WILL NOT BE DISTRIBUTED. This price list is intended for

More information

CX C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX370C

CX C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX370C CX C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX370C CX C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX370C Clean power Case C Series excavators use clean and efficient Tier 4 interim diesel engines.

More information

SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 61,950 lbs. ( kg) Digging Depth: 47 ft. 9 in. (14.56 m)

SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 61,950 lbs. ( kg) Digging Depth: 47 ft. 9 in. (14.56 m) SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 61,950 lbs. (28 100 kg) Digging Depth: 47 ft. 9 in. (14.56 m) Cab The Link-Belt X3 cab is the strongest and roomiest LBX has ever offered. The X3 cab

More information

CRAWLER EXCAVATORS EH160 LC. Specifications.

CRAWLER EXCAVATORS EH160 LC. Specifications. CRAWLER EXCAVATORS Specifications EH160 LC www.newhollandconstruction.com EH160 LC MACHINE DIMENSIONS A M C E I F L G H D K J B Standard Arm Optional Arm Arm Length 10 2 (3.10 m) 8 6 (2.60 m) A. Overall

More information

308E. Mini Hydraulic Excavator

308E. Mini Hydraulic Excavator 308E Mini Hydraulic Excavator Engine Weights Engine Model Cat C3.3 DI Turbo Operating Weight Standard Stick 7160 kg Net Power @ 2,400 rpm 46.8 kw Operating Weight Long Stick 7190 kg Gross Power @ 2,000

More information

7. 5 M E T R I C T O N EXCAVATOR C 7 5 C

7. 5 M E T R I C T O N EXCAVATOR C 7 5 C 7. 5 M E T R I C T O N C EXCAVATOR Specifications Engine Type................................... Isuzu CC-4JG1 naturally aspirated direct-injection diesel; certified to EPA Tier 2 emissions Net Peak Power

More information

Specif ications R125LCR-9A

Specif ications R125LCR-9A Specif ications R125LCR-9A ENGINE MODEL PERKINS 1204E Water cooled, 4 cycle Diesel, 4-cylinders Type in line, direct injection, turbocharged, charged air cooled and low emission Rated flywheel horse power

More information

SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 55,336 lbs. ( kg) Digging Depth: 22 ft. 8 in. (6.90 m)

SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 55,336 lbs. ( kg) Digging Depth: 22 ft. 8 in. (6.90 m) SAE Net Horsepower: 177 HP (132 kw) Operating Weight: 55,336 lbs. (25 100 kg) Digging Depth: 22 ft. 8 in. (6.90 m) Cab The Link-Belt X3 cab is the strongest and roomiest LBX has ever offered. The X3 cab

More information

Doosan Infracore DX700LC TECHNICAL DATA

Doosan Infracore DX700LC TECHNICAL DATA Doosan Infracore Construction Equipment DX700LC TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL ISUZU AH6WG1XYSC01 NUMBER OF CYLINDERS 6 RATED FLYWHEEL POWER hp / rpm 463 / 1,800 (GROSS)

More information

Swing torque 80,800 N m (59,595 lbf ft) Two variable displacement piston pumps L/min ( gal/min) 34.3/37.3 MPa (4,975 / 5,410 psi)

Swing torque 80,800 N m (59,595 lbf ft) Two variable displacement piston pumps L/min ( gal/min) 34.3/37.3 MPa (4,975 / 5,410 psi) 925E EXCAVATOR Tier 4 Final / Stage IV Specifications Operating weight 25,500 kg (56,218 lb) Operating weight includes coolant, lubricants, full fuel tank, cab, standard shoes, boom, arm, bucket and operator

More information

ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX210/210LC kw (150 hp)

ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX210/210LC kw (150 hp) ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX210/210LC-5 119 kw (150 hp) zx210/210lc-5 ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS Engine ZX210-5 / ZX210LC-5 Manufacturer and Model Isuzu 4HK1 Non-Road Emission Standards

More information

ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX180LC kw (121 hp)

ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX180LC kw (121 hp) ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS ZX180LC-5 90 kw (121 hp) ZX180LC-5 ZAXIS DASH-5 UTILITY-CLASS EXCAVATORS Engine ZX180LC-5 Manufacturer and Model Isuzu 4JJ1 Non-Road Emissions Standards Certified

More information

ZAXIS. 210/210LC-5 n 119 kw (159 hp)

ZAXIS. 210/210LC-5 n 119 kw (159 hp) n 119 kw (159 hp) EnginE Manufacturer and Model... Isuzu 4HK1 Non-Road Emission Standards... certified to IT4 / Stage IIIB emissions Net Rated Power (ISO 9249)... 119 kw (159 hp) @ 1,900 rpm Cylinders...

More information

FORESTRY. For Use in Log-Loading, Road Building and Harvester Processing Applications. Engine. Cab and Controls. Logging Attachment with Live-Heel

FORESTRY. For Use in Log-Loading, Road Building and Harvester Processing Applications. Engine. Cab and Controls. Logging Attachment with Live-Heel FORESTRY For Use in Log-Loading, Road Building and Harvester Processing Applications Engine Isuzu AH-6HK1XYSS Tier 3 turbocharged diesel engine with electronic fuel control, 6-cylinder, water-cooled, EGR

More information

TOUGH WORLD. TOUGH EQUIPMENT.

TOUGH WORLD. TOUGH EQUIPMENT. Engine Yanmar 4TNV98 Net Power 44.5 kw (60 hp) Operating Weight 7,500 kg Bucket Capacity 0.32 m³ 908E EXCAVATOR TOUGH WORLD. TOUGH EQUIPMENT. 1 MAXIMIZE YOUR RETURN ON INVESTMENT POWERFUL ENGINE The 908E

More information

Two variable displacement piston pumps L/min (2 x 79.3 gal/min) 34.3/37.3 MPa (4,975 / 5,410 psi) Travel circuit 34.

Two variable displacement piston pumps L/min (2 x 79.3 gal/min) 34.3/37.3 MPa (4,975 / 5,410 psi) Travel circuit 34. 922E EXCAVATOR Tier 4 Final / Stage IV Specifications Operating weight 22,800 kg (50,265 lb) SWING SYSTEM ELECTRIC SYSTEM Operating weight includes coolant, lubricants, full fuel tank, cab, standard shoes,

More information

Hydraulic. Open center, load sensing Main Pumps. 2 variable-displacement axial-piston pumps Maximum Rated Flow 105 L/m (28 gpm) x 2 Pilot Pump

Hydraulic. Open center, load sensing Main Pumps. 2 variable-displacement axial-piston pumps Maximum Rated Flow 105 L/m (28 gpm) x 2 Pilot Pump 14 Engine Base engine for use in the U.S., U.S. Territories, and Canada Optional engine for use outside the U.S. and U.S. Territories Manufacturer and Model John Deere PowerTech PWX John Deere 4045H Non-Road

More information

ZAXIS DASH-5 utility-class EXCAVAtORS. ZX250lC kw (188 hp)

ZAXIS DASH-5 utility-class EXCAVAtORS. ZX250lC kw (188 hp) ZAXIS DASH-5 utility-class EXCAVAtORS ZX250lC-5 140 kw (188 hp) ZX250lC-5 ZAXIS DASH-5 utility-class EXCAVAtORS Engine ZX250LC-5 Manufacturer and Model Isuzu 4HKIZXSA-01 Non-Road Emissions Standards EPA

More information

QUALITY YOU CAN TRUST C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX470C CX470C MASS EXCAVATION EXPERTS FOR THE REAL WORLD SINCE 1842

QUALITY YOU CAN TRUST C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX470C CX470C MASS EXCAVATION EXPERTS FOR THE REAL WORLD SINCE 1842 C-SERIES HYDRAULIC EXCAVATORS CX300C I CX350C I CX470C CX470C MASS EXCAVATION QUALITY YOU CAN TRUST www.casece.com EXPERTS FOR THE REAL WORLD SINCE 1842 MAIN REASONS TO CHOOSE THE C-SERIES HIGH EFFICIENCY

More information

305 CR. Mini Hydraulic Excavator

305 CR. Mini Hydraulic Excavator 305 CR Mini Hydraulic Excavator Engine Power Gross 32 kw 43 hp Net 31.3 kw 42 hp Maximum Operating Weight With cab 4990 kg 11,000 lb With canopy 4940 kg 10,890 lb 305 CR Mini Hydraulic Excavator Designed

More information

TXC 225LC-1 HYDRAULIC EXCAVATOR TXC 225LC-1. Hydraulic Excavator

TXC 225LC-1 HYDRAULIC EXCAVATOR TXC 225LC-1. Hydraulic Excavator Hydraulic Excavator OPERATING WEIGHT NET ENGINE POWER MAX DIG DEPTH MAX REACH 47,400 lbs (21,500 kg) 148 hp (110 kw) @ 1,950 rpm 21' 9" (6,630 mm) 32' 6" (9,910 mm) HYDRAULIC EXCAVATOR FEATURES Powerful,

More information

HYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for auxiliary & backfill blade

HYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for auxiliary & backfill blade CX25 Compact Excavator ENGINE Model... Yanmar 3TNE74-NYBB Cylinders... 3 Bore/Stroke... 2.91 x 3.07 (74 x 78 mm) Displacement... 61.6 in 3 (1010 cc) Fuel injection... Direct Fuel injection pump...mechanical

More information

Doosan Infracore DX225LL TECHNICAL DATA

Doosan Infracore DX225LL TECHNICAL DATA Doosan Infracore Construction Equipment DX225LL TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL Doosan DL06 NUMBER OF CYLINDERS 6 RATED FLYWHEEL POWER hp / rpm 155 / 1,900 (hp PER SAE J1995)

More information

290G LC. 147 kw (197 hp)

290G LC. 147 kw (197 hp) 290G LC 147 kw (197 hp) 290G LC Engine 290G LC Base engine for use in U.S., U.S. Territories, and Canada Optional engine for use outside the U.S. and U.S. Territories Optional engine for use outside the

More information

250G LC. 142 kw (191 hp)

250G LC. 142 kw (191 hp) 250G LC 142 kw (191 hp) 250G LC Engine 250G LC Base engine for use in U.S., U.S. Territories, and Canada Optional engine for use outside the U.S. and U.S. Territories Optional engine for use outside the

More information

EQUIPMENT ENGINE HYDRAULIC SYSTEM

EQUIPMENT ENGINE HYDRAULIC SYSTEM EQUIPMENT ENGINE Model... Isuzu AI-4JJ1X Type... 4-cycle water-cooled, direct injection Aspiration... Turbocharged, intercooled No. of cylinders... 4 Rated power ISO 9249, net... 90.2 kw (121 HP) at 2

More information

EC160B NLC VOLVO EXCAVATOR MONOBLOCK/2-PIECE BOOM

EC160B NLC VOLVO EXCAVATOR MONOBLOCK/2-PIECE BOOM VOLVO EXCAVATOR EC160B LC EC160B NLC MONOBLOCK/2-PIECE BOOM Engine power, gross: 90 kw (121 hp) Operating weight: LC: 16.6 ~ 18.4 t NLC: 16.5 ~ 18.3 t Buckets (SAE) 775 ~ 1,225 l Turbocharged VOLVO diesel

More information

CX C-SERIES HYDRAULIC EXCAVATORS CX130C I CX160C I CX180C

CX C-SERIES HYDRAULIC EXCAVATORS CX130C I CX160C I CX180C CX C-SERIES HYDRAULIC EXCAVATORS CX130C I CX160C I CX180C CX C-SERIES HYDRAULIC EXCAVATORS CX130C I CX160C I CX180C Clean power Case C Series excavators use clean and effi cient Tier 4 interim diesel engines.

More information

EC210B LC EC210B NC/EC210B NLC

EC210B LC EC210B NC/EC210B NLC VOLVO EXCAVATOR EC210B LC EC210B NC/EC210B NLC MONOBLOCK/2-PIECE BOOM Engine power, gross: 119 kw (159 hp) Operating weight: LC: 21,3 ~ 22,3 t NC: 20,9 ~ 21,8 t NLC: 21,5 ~ 22,2 t Buckets (SAE): 750 ~

More information

EC140C VOLVO EXCAVATOR. 28,110 32,370 lb, 92 hp

EC140C VOLVO EXCAVATOR. 28,110 32,370 lb, 92 hp EC140C VOLVO EXCAVATOR 28,110 32,370 lb, 92 hp SPECIFICATIONS Engine The Volvo diesel engine delivers lower emissions, along with superior performance and fuel efficiency. The EPA Tier 3 compliant engine

More information

HYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for breaker & backfill blade

HYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for breaker & backfill blade CX47 Compact Excavator ENGINE Model... Yanmar 4TNE88-EYBC Cylinders... 4 Bore/Stroke... 3.46 x 3.54 (88 x 90 mm) Displacement... 133.5 in 3 (2180 cc) Fuel injection... Direct Fuel injection pump... Electronic

More information

307E2. Mini Hydraulic Excavator

307E2. Mini Hydraulic Excavator 307E2 Mini Hydraulic Excavator Engine Weights Engine Model* Cat C2.4 Turbo Operating Weight with Cab 7270 kg 16,028 lb Net Power (ISO 9249) 37.7 kw 50.6 hp Operating Specifications *Engine meets U.S. EPA

More information

HYDRAULIC EXCAVATOR PC308USLC-3 308US. NET HORSEPOWER 134 kw rpm OPERATING WEIGHT kg 70,383 73,146 lb

HYDRAULIC EXCAVATOR PC308USLC-3 308US. NET HORSEPOWER 134 kw rpm OPERATING WEIGHT kg 70,383 73,146 lb NET HORSEPOWER 134 kw 179 HP @ 2050 rpm OPERATING WEIGHT 31925 33178 kg 70,383 73,146 lb PC308USLC-3 BUCKET CAPACITY 0.74 1.87 m 3 0.97 2.45 yd 3 PC 308US LC Photo may include optional equipment. HYDRAULIC

More information

TRACKED EXCAVATOR JS370 LONG REACH. Net engine power: 210kW (281hp) Operating weight: 41149kg 42039kg Bucket capacity: 0.38m 3 0.

TRACKED EXCAVATOR JS370 LONG REACH. Net engine power: 210kW (281hp) Operating weight: 41149kg 42039kg Bucket capacity: 0.38m 3 0. TRACKED EXCAVATOR JS370 LONG REACH Net engine power: 210kW (281hp) Operating weight: 41149kg 42039kg Bucket capacity: 0.38m 3 0.79m 3 STATIC DIMENSIONS I E H M N J F K L G C D A B Illustration shows optional

More information

307E2. Mini Hydraulic Excavator. Standard Bucket Size 0.33 m 3 Engine Model Cat C2.6 DI Turbo Bucket Width 854 mm Net Power 41.5 kw (55.

307E2. Mini Hydraulic Excavator. Standard Bucket Size 0.33 m 3 Engine Model Cat C2.6 DI Turbo Bucket Width 854 mm Net Power 41.5 kw (55. 307E2 Mini Hydraulic Excavator Bucket Engine Standard Bucket Size 0.33 m 3 Engine Model Cat C2.6 DI Turbo Bucket Width 854 mm Net Power 41.5 kw (55.6 hp) Gross Power @ 2,000 rpm 43 kw (57.6 hp) Weights

More information

DL250 TECHNICAL DATA

DL250 TECHNICAL DATA DL250 TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL ea. Doosan DL06 NUMBER OF CYLINDERS ea. 6 RATED FLYWHEEL POWER hp / rpm 163 / 2,100 (GROSS) (SAE J1995) kw / rpm 121 / 2,100 RATED

More information

EC240B Lc EC240B NLC MONOBLOCK/2-PIECE BOOM. more care. built in. VOLVO EXCAVATOR

EC240B Lc EC240B NLC MONOBLOCK/2-PIECE BOOM. more care. built in. VOLVO EXCAVATOR VOLVO EXCAVATOR EC240B Lc EC240B NLC MONOBLOCK/2-PIECE BOOM Engine power, gross: 134 kw (180 hp) Operating weight: LC: 24.2 ~ 25.8 t NLC: 24.8 ~ 25.7 t Turbocharged VOLVO diesel engine with water cooling,

More information

305 CR. Mini Hydraulic Excavator. Stage II Compliant. Engine Power kw/42 hp. Maximum Operating Weight

305 CR. Mini Hydraulic Excavator. Stage II Compliant. Engine Power kw/42 hp. Maximum Operating Weight 305 CR Mini Hydraulic Excavator Stage II Compliant Engine Power Gross Net Maximum Operating Weight With cab With canopy 32 kw/43 hp 31.3 kw/42 hp 4990 kg 4940 kg 305 CR Mini Hydraulic Excavator Designed

More information

121F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED

121F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED 121F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Type FPT F5H FL463 C*F001 Tier 4 Final 4-stroke Cylinders 4 Bore/ 3.9 x 4.3 in (99 x 110 mm) Displacement 207 in 3

More information

21F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED

21F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED 21F COMPACT WHEEL LOADER TIER 4 FINAL CERTIFIED ENGINE Model Emissions Certification Type FPT F5H FL463 B*F001 Tier 4 Final 4-stroke Cylinders 4 Bore/ 3.9 x 4.3 in (99 x 110 mm) Displacement 207 in 3 (3.4

More information

324D/ 324D L. Hydraulic Excavator. Engine Engine Model. ACERT Technology. Net Flywheel Power Weights. Std. Undercarriage. Long Undercarriage

324D/ 324D L. Hydraulic Excavator. Engine Engine Model. ACERT Technology. Net Flywheel Power Weights. Std. Undercarriage. Long Undercarriage D/ D L Hydraulic Excavator Engine Engine Model Net Flywheel Power Weights Operating Weight Std. Undercarriage Operating Weight Long Undercarriage Cat C with ACERT Technology 0 kw 0 kg 0 kg Engine Engine

More information

Cummins / 6CTA8.3-C or Rhino Tier 2 (Tier 3, Tier 4) 6 8.3(506) 188(252) Direct Injection Turbocharged, air-to-air charge air cooler COOLING Fan Drive

Cummins / 6CTA8.3-C or Rhino Tier 2 (Tier 3, Tier 4) 6 8.3(506) 188(252) Direct Injection Turbocharged, air-to-air charge air cooler COOLING Fan Drive 330 EXCAVATOR ENGINE Engine Make/ Engine Model Emission Rating (optional) Cylinders Displacement L (cu. In) Net Power kw (Hp) @2,200 rpm Fuel System Aspiration Cummins / 6CTA8.3-C or Rhino Tier 2 (Tier

More information

303 CR. Mini Hydraulic Excavator

303 CR. Mini Hydraulic Excavator 303 CR Mini Hydraulic Excavator Engine Power Gross 20.2 kw 27.1 hp Net 19.5 kw 26.1 hp Maximum Operating Weight With cab 3420 kg 7524 lb With canopy 3330 kg 7326 lb 303 CR Mini Hydraulic Excavator Designed

More information

With Tier 4 Interim Engine installed. hyundai heavy industries

With Tier 4 Interim Engine installed. hyundai heavy industries With Tier 4 Interim Engine installed hyundai heavy industries 1 Pride at Work Hyundai Heavy Industries strives to build state-of-the art earthmoving equipment to give every operator maximum performance,

More information

Doosan Infracore DL220 TECHNICAL DATA

Doosan Infracore DL220 TECHNICAL DATA Doosan Infracore Construction Equipment DL220 TECHNICAL DATA GENERAL SPECIFICATIONS ITEMS UNIT STANDARD MODEL ea. Doosan DL06 NUMBER OF CYLINDERS ea. 6 RATED FLYWHEEL POWER hp / rpm 148 / 2,200 (GROSS)

More information