RT540E. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. Dimensions ton (35 mt) capacity

Transcription

1 RT5E product guide contents Features 2 features ton ( mt) capacity 32 ft. - 2 ft. (9.8 m m) 4-section, full power boom 26 ft. - ft. (7.9 m m) offsettable telescopic swing-away extension Full frame decking Rounded cab design Dual-axis electric joystick controllers 1 hp (119 kw) Cummins diesel engine (tier III) Specifications 3 Dimensions 5 Working Range 6 Load Charts 7 Rough Terrain Hydraulic Crane

2 features 2 The RT5E incorporates a rectangular boom shape made from 0k.s.i. steel which eliminates weight and maximizes structural capacities. Rounded steel cab design provides aesthetic appeal. Automotive-style dash control panel designed to offer a less cluttered look while still offering full instrumentation. Max. tip height of 154 ft. (47.0 m) w/ ft. (13.7 m) telescopic extension. Cummins QSB 6.7L diesel engine provides plenty of power at the jobsite and meets current emission standards.

3 specifications Superstructure B Boom 32 ft. - 2 ft. (9.8 m m) four-section, synchronized full power boom. Maximum tip height: 1 ft. (33.6 m). *Optional Fixed Swingaway Extension 26 ft. (7.9 m) offsettable fixed swingaway extension. Offsets at and 3. Stows alongside base boom section. Maximum tip height: 1 ft. (41.1 m). *Optional Telescopic Swingaway Extension 26 ft. - ft. (7.9 m m) offsettable telescopic lattice swingaway extension. Offsets at, 15 and 3. Stows alongside base boom section. Maximum tip height: 154 ft. (47.0 m). B Boom Nose Four nylatron sheaves mounted on heavy duty tapered roller bearings with removable pin-type rope guards. Quick reeve type boom nose. Boom Elevation One double-acting hydraulic cylinder with integral holding valve provides elevation from -3 to +78. Load Moment & Anti-Two Block System Standard Graphic Display load moment and anti-two block system with audio-visual warning and control lever lockout. These systems provide electronic display of boom angle, length, radius, tip height, relative load moment, maximum permissible load, load indication and warning of impending two-block condition. The standard Work Area Definition System allows the operator to pre-select and define safe working areas. If the crane approaches the pre-set limits, audio-visual warnings aid the operator in avoiding job-site obstructions. C Cab Full vision, all steel fabricated with acoustical lining and tinted safety glass throughout. Deluxe seat incorporates armrestmounted electric dual-axis controllers. Dash panel incorporates gauges for all engine functions. Other standard features include: tilt steering wheel, hot water heater, cab circulating air fan, sliding side and rear windows, sliding skylight with electric wiper and sunscreen, electric windshield wash/wipe, fire extinguisher and seat belt. Counterweight 9,490 lbs. (4 305 kg) pinned to superstructure. Hydraulic System Two main pumps ([1] piston and [1] gear) with a combined capacity of 83.6 GPM (316.5 LPM). Maximum operating pressure: 4,000 psi (275.7 bar). Three section pressure compensated valve bank. Return line type filter with full flow by-pass protection and service indicator. Replaceable cartridge with micron filtration rating of 5/12/ gallon (396 L) hyd. reservoir. System pressure test ports. HOIST SPECIFICATIONS (HP15C-17G) Main and Auxiliary Hoist Planetary reduction with automatic spring applied multi-disc wet brake. Electronic hoist drum rotation indicators, and hoist drum cable followers. Maximum Single Line Pull: 1st layer: 11,6 lbs. (5 2 kg) 3rd layer: 9,530 lbs. (4 323 kg) 5th layer: 8,0 lbs. (3 656 kg) Maximum Permissible Line Pull: 11,6 lb. (5 2 kg.) with 6x37 class rope 11,6 lb. (5 2 kg.) with x7 class rope Maximum Single Line Speed: 4 FPM (136 m/min) Rope Construction: 6x36 EIPS IWRC, Special Flexible x7 Flex-X, Rotation Resistant Rope Diameter: 5/8 in. (16 mm) Rope Length: Main Hoist 4 ft. (137.0 m) Auxillary Hoist 4 ft. (137.0 m) Maximum Rope Stowage: 596 ft. (181 m) *Denotes optional equipment 3 Swing Single speed, planetary swing drive with foot applied multi-disc wet brake. Spring applied, hydraulically released swing brake. Single position mechanical house lock, operated from cab. Maximum speed: 2.0 RPM. RT5E

4 specifications 4 Carrier FChassis Box section frame fabricated from high-strength, low alloy steel. Front/rear towing and tie down lugs. O Outrigger System Four hydraulic telescoping single-stage double box beam outriggers with inverted jacks and integral holding valves. Three position setting, 0%, % and fully extended. All steel fabricated quick release type outrigger floats, in. (362 mm) square. Maximum outrigger pad load: 58,000 lbs. ( kg) Outrigger Controls Controls and crane level indicator located in cab. Engine (Tier III) Cummins QSB 6.7L diesel, six cylinders, 1 bhp (119 kw) 2,0 RPM. Maximum torque: 5 ft. lb. (732 1,0 RPM. Fuel Tank Capacity 58 gallons (219 L) Transmission Range-shift 6 speed (3 speeds x 2 range, both forward & reverse). Front axle disconnect for 4 x 2 travel. Electrical System Two 12 V - maintenance free batteries. 12 V starting and lighting. Battery disconnect. CanBus Diagnostic system. Oscillation Lockouts Automatic full hydraulic lockouts on rear axle permits in. (25.4 cm) oscillation only with boom centered over the front. Brakes Full hydraulic split circuit disc-type brakes operating on all wheels. Spring-applied, hydraulically released parking brake mounted on front axle. Tires Std x bias ply L Lights Full lighting including turn indicators, head, tail, brake and hazard warning lights. Maximum Speed 25 MPH ( 20 r.p.m. Gradeability (Theoretical) 119% (at engine stall) (Based on 62,532 lb. [ kg] GVW) 20.5 x 25 tires, 2 ft. (31.0m) main boom, plus ft. (13.7m) telescopic swingaway, 9,490 lb. (4 305 kg) counterweight, T (mt) hookblock and 7.5 T (6.8mt) headache ball. Miscellaneous Standard Equipment Full width steel fenders, full length steel decking with anti-skid, dual rear view mirrors, hook-block tiedown, electronic back-up alarm, light package, front stowage well, tachometer/hourmeter, rear wheel position indicator, 36,000 Btu hot water cab heater, hoist mirrors, engine distress A/V warning system, front/rear tie down and tow lugs, coolant sight level indicator. RT5E Drive 4 x 4 Steering Fully independent power steering: Front: Full hydraulic steering wheel controlled. Rear: Full hydraulic switch controlled. Provides infinite variations 4 main steering modes: front only, rear only, crab and coordinated. Rear steer indicator. Outside turning radius: 19.1 ft. (5.8m) Inside turning radius: 13.1 ft. (4.0m) Axles Front: Drive/steer with differential and planetary reduction hubs rigid mounted to frame. Rear: Drive/steer with differential and planetary reduction hubs pivot mounted to frame. *Optional Equipment * AUXILIARY HOIST PACKAGE (includes Model HP15C-17G auxiliary hoist with electronic hoist drum rotation indicator, hoist drum cable follower, 4 ft. (137.0 m) of 5/8 in. (16 mm) x 7 class wire rope and auxiliary single sheave boom nose. *AUXILIARY LIGHTING PACKAGE (includes cab mounted amber flashing light, hoist mounted worklights, and dual base boom mounted floodlights). *LMI light bar (in cab) *Air conditioning (28,0 BTU) *36 NYC style mechanical swing lock *Rear Pintle hook *Cab-controlled cross axle differential locks (front & rear) *PAT Data logger down-load kit *Rubber mat for stowage trough *Denotes optional equipment

5 2 WHEEL STEER 4 WHEEL STEER TIRE SIZE A B C D E F G H J K L M 20.5 X X X X NOTES: 1. ALL DIMENSIONS ARE FOR REFERENCE ONLY 2. BOOM ELEVATION IS -3 TO DIMS SHOWN BASED ON 20.5 X 25 TIRES. ADD 34.5 MM FOR 16.0 X 25 TIRES [20 FT 2 IN] dimensions 5 6 [25.19] 2387 [941] RETRACTED 4267 [168] MID EXTEND 96 [2] FULL EXTEND 641 [25.26] BOOM NOSE WIDTH H TRACK M OVER TIRES A B C D OUTSIDE CURB CLEARANCE E OUTSIDE TURNING RADIUS F INSIDE TURNING RADIUS S/S OVERALL [39-2 ] G INSIDE CURB CLEARANCE R3796 [149.5] TAIL SWING 1172 [46.14] 3283 [129.24] BOOM HORIZONTAL [18.34] [62.25] 3 32 [127.37] TOP OF HOIST J L CL ROTATION K 4722 [185.92] 3 3 [14.56] CL O/R BOX [18.] 2951 [116.18] WHEELBASE 36 [144.09] 98 [279.46] 1905 [75.00] 3196 [125.83] O/R CL BOX NOTE: [ ] Reference dimensions in inches Weights RT5E Basic Machine GVW Front Rear lb. kg lb. kg lb. kg Basic Machine including 2 ft. (31.0m) main boom, main hoist with 4 ft. (137.0m) of rope, full counterweight + IPO, 7.5 T (6.8mt) headache ball, and T (mt) hookblock:, , , ADD: Auxiliary hoist + 4 ft. (137.0m) of x7 hoist cable and auxiliary boom nose ILO IPO C/W, , , ADD: Fixed 26 ft. (7.9m) offsettable boom extension + extension hangers 62, , , OR ADD: 26 ft. - ft. ( m) telescopic boom extension + extension hangers 62, , , RT5E

6 working range Working range 2 ft. Main Boom ft. extension 6 (BOOM DEFLECTION NOT SHOWN) WORKING RANGE DIAGRAM D O o ' EXT o 26' EXT HEIGHT FROM GROUND IN FEET o o o o o 2 90 BOOM LENGTH AND EXTENSION IN FEET 20 o o 76 o MAX. BOOM ANGLE 0 o OPERATING RADIUS IN FEET FROM AXIS OF ROTATION AXIS OF ROTATION RT5E 8'-2" 7'-8" DIMENSIONS ARE FOR LARGEST GROVE FURNISHED HOOK BLOCK AND HEADACHE BALL, WITH ANTI-TWO BLOCK ACTIVATED. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

7 RT5E load chart 32-2 ft. 9,490 lbs 0% 23' 4" spread º ,000 (69) 72,200,0 48,0 (65) (.5) (75) 61,000,0 48,0 *46,0 (61) 47,9 48,0 48,0 44,300 *38,0 (54) (69) (73) 34,5,000,0,300 31,000 29,0 *22,000 (41) (53.5) (71.5) (74) 26,300 26,0 27,200 27,0 25,0 24,0 22,000 *18,0 (20.5) (43.5) (55.5) (67) (.5) (73) 21,2 21,6 21,8 21,0 20,0 18,3 17,0 (30) (47.5) (56.5) (66.5) (69.5) (73) 17,6 17,900 18,0 17,0 15,0 15,200 (38.5) (.5) (57.5) (66) () 14,0 14,4 14,6 14,0 13,0 13,200 (26.5) (43.5) (52.5) (58.5) (66.5) 11,6 11,0 11,900 11,7 11,0 () (46.5) (54) (63.5) 9,4 9,6 9,7 9,7 9,790 (24.5) (.5) (49) (55) (.5) 7,9 8,0 8,1 8,130 (33) (44) (51) (57) 6,0 6,720 6,7 6,0 (23) (38) (46.5) (53.5) 5,590 5,6 5,7 (31) (42) (49.5) 4,6 4,7 4,0 (21.5) (36) (.5) 3,9 4,0 (29.5) (41) 3,2 3,3 (21) (36) 2,7 (30.5) 2,2 (23) 1,0 (9.5) 0 2 Minimum boom angle ( ) for indicated length Maximum boom length (ft.) at boom angle #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum boom angle. Boom Angle Lifting Capacities at Zero Degree Boom Angle ,9 18,0 12,1 8,1 5,7 4,030 2,0 1,7 (26) (33.8) (43.8) (53.8) (63.8) (73.8) (83.8) (95.5) 7 NOTE: ( ) Reference radii in feet. A THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. RT5E

8 RT5E load chart ft. 26 ft. 9,490 lbs 0% 3º Min. boom angle for indicated length Max. boom length at boom angle #LMI operating code. Refer to LMI manual for instructions. *This capacity based on maximum boom angle. 26 ft. LENGTH #0051 # *8,200 8,200 8,200 *5,7 () 8,1 5,7 7,0 5,4 (65) () 6,4 4,9 5,4 4,4 () (64.5) 4,620 4,0 (57.5) (62) 3,900 3,6 (54.5) 3,2 3,3 (51.5) (56) 2,7 3,0 (48.5) (53) 2,2 2,5 () (49.5) 1,7 2,0 (41.5) (46) 1,3 1,620 (38) (41.5) 1,020 1,200 (33.5) (37) ft. A ft ft. 9,490 lbs 0% 3º 26 ft. LENGTH ft. LENGTH #0021 #0022 #0023 #0041 #0042 # *,200 9,4 *7,7 *5,2 8,7 7,3 *6,030 5,2 () (72) (73.5) 8,1 6,8 (69.5) 5,7 5,0 (71.5) 3,6 55 7,5 6,0 5,520 4,6 3,5 (65) (67) () (69.5) 6,0 5,3 5,290 4,290 3,430 *3,000 (64.5) (67) (.5) 65 5,990 4,7 4,8 4,000 3,320 2,890 () (62) (64.5) (65) (68.5) 5,2 4,2 4,2 3,0 3,220 2,790 (57.5) (62) (63) (66) (.5) 75 4,0 3,7 3,0 3,6 3,130 2,0 (54.5) (56) (.5) (64) (68) 3,6 3,330 3,3 3,520 3,000 2,620 (51.5) (53.5) (56) (58.5) (61.5) (65.5) 85 3,0 (48.5) 2,9 (.5) 3,0 (53) 3,3 (56) 2,8 2,5 (63) 90 2,0 () 2,590 (47) 2,6 (49.5) 3,030 (53.5) 2,7 (56.5) 2,4 (.5) 95 2,020 (41.5) 2,130 (43.5) 2,2 (46) 2,6 (51) 2,6 (54) 2,4 (57.5) 0 1,590 1,6 1,790 2,2 2,5 2,3 (38) () (41.5) (48) (51.5) (55) 5 1,200 1,2 1,3 1,930 2,2 2,3 (33.5) (.5) (37) (.5) (48.5) (52) 1 1,630 1,890 2,030 (42.5) (.5) (48.5) 115 1,330 1,5 1,0 (39) (42) () 120 1,0 1,2 1,0 (.5) (38.5) (41) 125 1,0 (36.5) Min. boom angle for indicated length Max. boom length at boom angle ft. ft. A #LMI operating code. Refer to LMI manual for instructions. *This capacity based on maximum boom angle. RT5E BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold line are based on structural strength of boom extension ft. fixed extension lengths may be used for single line lifting service. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers fully extended and vertical jacks set only. 6. When lifting over the main boom nose with 26 ft. fixed extension erected, the outriggers must be fully extended or % extended (14' spread). BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold line are based on structural strength of boom extension ft. and ft. tele extension lengths may be used for single line lifting service. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers fully extended and vertical jacks set only. 6. When lifting over the main boom nose with 26 ft. or ft. tele extension erected, the outriggers must be fully extended or % extended (14' spread). THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

9 RT5E load charts 32 - ft. 9,490 lbs Stationary 3 o # ,0 24,0 23,000 (65) (.5) 12 21,0 22,0 21,0 (61) 15 15,2 15,5 16,0 13,900 (54) (68.5) 20 9,1 9,3 9,8 9,8 (41) (53.5) (62) 25 5,790 6,0 6,0 6,5 (20) (43) (55) (62) 30 3,9 4,2 4,3 (29.5) (47.5) (56) 2,7 2,900 (38) () 1,690 1,8 (26) (43) 1,030 (34.5) Minimum boom angle ( ) for indicated length 33 Maximum boom length (ft.) at boom angle #LMI operating code. Refer to LMI manual for operating instructions. Lifting Capacities at Zero Degree Boom Angle Boom Angle 32 5,290 (26) NOTE: ( ) Reference radii in feet. 2,8 (33.8) 1,0 (43.8) A ft. 9,490 lbs Pick & Carry (Max. 2.5 MPH) 20.5 x 25 Tires #9006 Defined Arc Over Front 32 27,1 (65) 26,900 (.5) 12 23,3 23,2 (61) 15 18,9 (54) 19,0 19,0 (69) 20 13,0 14,200 14,0 14,5 (41) (53.5) 25,0 (20),7 (43.5) 11,1 (55.5) 11,200 (62) 30 8,290 8,620 8,790 (30) (47.5) (56.5) 6,7 6,890 (38.5) () 5,2 5,390 (26.5) (43) 4,1 () 3,190 (24) Minimum boom angle ( ) for indicated length 0 Maximum boom length (ft.) at boom angle #LMI operating code. Refer to LMI manual for operating instructions. Lifting Capacities at Zero Degree Boom Angle Boom Angle 32 9,520 6,830 4,2 2,5 (26) (33.8) (43.8) (53.8) NOTE: ( ) Reference radii in feet. A NOTES TO ALL RUBBER CAPACITY CHARTS: 1. Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J Capacities are applicable to machines equipped with 20.5x25 (24 ply) tires at 75 psi cold inflation pressure, and 16.00x25 (28 ply) tires at 0 psi cold inflation pressure. 3. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation. 4. Capacities are applicable only with machine on firm level surface. 5. On rubber lifting with boom extensions not permitted. 6. For pick and carry operation, boom must be centered over front of machine, mechanical swing lock engaged and load restrained from swinging. When handling loads in the structural range with capacities close to maximum ratings, travel should be reduced to creep speeds. 7. Axle lockouts must be functioning when lifting on rubber. 8. All lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation pressures. See lifting capacity chart for tire used. Damaged tires are hazardous to safe operation of crane. 9. Creep - Not over 200 ft. of movement in any 30 minute period and not exceeding 1 mph. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. RT5E

10 load charts RT5E 32-2 ft. 9,490 lbs % 14 ft. spread 3º # ,000 (69) 66,2,0 48,0 (65) (.5) (75) 12 57,9,0 48,0 *46,0 (61) 15 46,300 44,200 41,0 39,5 *37,5 (54) (69) (73) 20 27,0 27,0 27,0 25,9 24,9 24,000 *22,000 (41) (53.5) (71.5) (74) 25 17,6 18,2 18,0 18,4 18,0 17,4 16,9 *16,3 (20.5) (43.5) (55.5) (67) (.5) (73) 30 12,8 13,200 13,300 13,5 13,2 12,9 12,0 (30) (47.5) (56.5) (66.5) (69.5) (73) 9,790 9,9,1,2,0 9,830 (38.5) (.5) (57.5) (66) () 7,0 7,520 7,7 7,9 7,9 7,820 (26.5) (43.5) (52.5) (58.5) (66.5) 5,7 5,9 6,1 6,1 6,190 () (46.5) (54) (63.5) 4,4 4,590 4,7 4,820 4,8 (24.5) (.5) (49) (55) (.5) 55 3,0 3,630 3,7 3,7 (33) (44) (51) (57) 2,6 2,730 2,8 2,890 (23) (38) (46.5) (53.5) 65 1,9 2,0 2,1 (31) (42) (49.5) 1,3 1,4 1,530 (21.5) (36) (.5) 75 1,000 (41) Minimum boom angle ( ) for indicated length Maximum boom length (ft.) at boom angle #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum boom angle. Lifting Capacities at Zero Degree Boom Angle Boom Angle 32 16,300,1 6,030 3,5 2,0 (26) (33.8) (43.8) (53.8) (63.8) NOTE: ( ) Reference radii in feet. A ft. 9,490 lbs 0% 7.8 ft. spread 3º # ,9 (69) 37,0,900 33,0 (65) (.5) (75) 12 29,0 28,0 26,0 *25,1 (61) 15 20,8 20,4 19,7 18,8 *18,000 (54) (69) (73) 20 12,0 13,0 12,9 12,0 12,1 11,0 *11,2 (41) (53.5) (71.5) (74) 25 7,9 8,4 8,0 8,7 8,5 8,300 8,0 *7,720 (20.5) (43.5) (55.5) (67) (.5) (73) 30 5,6 5,890 6,000 6,1 5,9 5,8 5,0 (30) (47.5) (56.5) (66.5) (69.5) (73) 3,9 4,090 4,3 4,2 4,200 4,0 (38.5) (.5) (57.5) (66) () 2,0 2,7 2,9 2,9 2,9 2,8 (26.5) (43.5) (52.5) (58.5) (66.5) 1,6 1,8 1,9 1,9 1,890 () (46.5) (54) (63.5) 1,020 1,1 1,1 1,1 (.5) (49) (55) (.5) Minimum boom angle ( ) for indicated length Maximum boom length ft.) ( at boom angle #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum boom angle. Lifting Capacities at Zero Degree Boom Angle Boom Angle 32 7,230 4,0 1,790 (26) (33.8) (43.8) NOTE: ( ) Reference radii in feet. A ft. 26 ft. 9,490 lbs % 14 ft.spread Min. boom angle for indicated length Max. boom length at boom angle #LMI operating code. Refer to LMI manual for instructions. *This capacity based on maximum boom angle. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold line are based on structural strength of boom extension ft. fixed extension lengths may be used for single line lifting service. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 6. When lifting over the main boom nose with 26 ft. fixed extension erected, the outriggers must be fully extended or % extended (14' spread). BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold line are based on structural strength of boom extension ft. and ft. tele extension lengths may be used for single line lifting service. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 6. When lifting over the main boom nose with 26 ft. or ft. tele extension erected, the outriggers must be fully extended or % extended (14' spread). THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 26 ft. LENGTH #51 #53 3 *8,200 7,2 5,7 *5,7 () 4,6 5,7 3,6 4,6 (65) () 2,8 3,720 2,1 2,900 () (64.5) 1,5 2,2 (57.5) (62) 1,030 1,620 (54.5) 1,0 (56) ft. 3º A ft ft. 9,490 lbs % 14 ft. spread #LMI operating code. Refer to LMI manual for instructions. *This capacity based on maximum boom angle. 3º 26 ft. LENGTH ft. LENGTH #21 #22 #23 #41 #42 # *9,120 7,2 *7,7 *5,2 5,7 () 6,4 (72) *6,030 5,2 (73.5) 4,6 5,200 (69.5) 5,7 5,0 (71.5) 3,6 55 3,6 (65) 4,1 (67) 4,6 () 4,2 (69.5) 3,5 2,8 3,320 (64.5) 3,720 3,4 (67) 3,430 (.5) *3, ,1 () 2,5 (62) 2,900 (64.5) 2,820 (65) 3,320 (68.5) 2,890 1,5 (57.5) 1,900 2,2 (62) 2,2 (63) 2,8 (66) 2,790 (.5) 75 1,030 (54.5) 1,3 (56) 1,620 1,7 (.5) 2,300 (64) 2,0 (68) 1,0 (56) 1,300 (58.5) 1,0 (61.5) 2,2 (65.5) 85 1,3 1,7 (63) 90 1,320 (.5) Min. boom angle for indicated length Max. boom length at boom angle ft. ft. A

11 load handling Weight Reductions for Load Handling Devices 26 ft. Fixed Boom Extension *Erected 2,7 26 ft.- ft. Tele. Boom Extension *Erected (Retracted) 3,7 *Erected (Extended) 5,0 11 *Reduction of main boom capacities Auxiliary Boom Nose 5 Hookblocks and Headache Balls Ton, 3 Sheave (14" sheave) Ton, 3 Sheave (12" sheave) Ton, 4 Sheave (CE) Ton Overhaul Ball Refer to rating plate for actual weight. Line Pulls and Reeving Information Permissible Nominal Hoists Cable Specs Line Pulls Cable Length 5/8" (16 mm) 6x37 Class Main EIPS, IWRC Special Flexible 11,6 lb. 4 ft. Min. Breaking Str. 41,200 lb. 5/8" (16 mm) Flex-X Main & Aux. Rotation Resistant (non-rotating) 11,6 lb. 4 ft. Min. Breaking Str. 61,200 lb. When lifting over swingaway and/or jib combinations, deduct total weight of all load handling devices reeved over main boom nose directly from swingaway or jib capacity. NOTE: All load handling devices and boom attachments are considered part of the load and suitable allowances MUST BE MADE for their combined weights. Weights are for Grove furnished equipment. Hoist Performance Wire Hoist Line Pulls Drum Rope Rope Two Speed Hoist Capacity (ft.) Layer Low High Available lb.* Available lb.* Layer Total 1 11,6 7, ,4 6, ,530 6, ,730 5, ,0 5, ,490 4, *Max. lifting capacity: 6x37 class = 11,6 lb. x7 class = 11,6 lb. Working Area Diagram DIAGRAM OF WORKING AREA CENTERLINE OF BOOM 3 o OVER SIDE CENTERLINE OF OUTRIGGER SUPPORT LONGITUDINAL CENTERLINE OF CRANE BOOM CENTERED OVER FRONT 3 o REAR AXLE OSCILLATION LOCKOUTS MUST BE SET TO MAINTAIN 3 o CAPACITIES CG OF LOAD OVER FRONT + + OVER REAR 12 o 6 o SEE NOTE AT BOTTOM FRONT LIFTING ON OUTRIGGERS OVER SIDE CENTERLINE OF ROTATION LIFTING ON TIRES BOLD LINES DETERMINE THE LIMITING POSITION OF ANY LOAD FOR OPERATION WITHIN WORKING AREAS INDICATED Bold lines determine the limiting position of any load for operation within working areas indicated. C C THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. RT5E

12 Manitowoc Crane Group - Americas Manitowoc, Wisconsin Facility Tel: [Int + 001] Fax: [Int + 001] Shady Grove, Pennsylvania Facility Tel: [Int + 001] Fax: [Int + 001] Manitowoc Crane Group - EMEA Europe Middle East & Africa Tel: [Int + 33] (0) Fax: [Int + 33] (0) Manitowoc Crane Group - UK Europe Middle East & Africa Tel: [Int + 44] (0) Fax: [Int + 44] (0) Manitowoc Crane Group - Germany (Sales, Parts & Service) Tel: [Int + 49](0) Fax: [Int + 49] (0) Manitowoc Crane Group - France France & Africa (Sales, Parts & Service) Tel: [Int + 33] (0) Fax: [Int + 33] (0) Manitowoc Crane Group - Netherlands (Sales, Parts & Service) Tel: [Int + 31] (0) Fax: [Int + 31] (0) Manitowoc Crane Group - Italy Italy & Southern Europe (Sales, Parts & Service) Tel: [Int + 39] (0) Fax: [Int + 39] (0) Manitowoc Crane Group - Portugal Portugal & Spain (Sales, Parts & Service) Tel: [Int + 1] (0) Fax: [Int + 1] (0) Manitowoc Crane Group - Singapore Asia/Pacific excl China (Sales, Parts & Service) Tel: [Int + 65] Fax: [Int + 65] 6862 / 4142 Manitowoc Crane Group - Shanghai China (Sales, Parts & Service) Tel: [Int + 86] (0) Fax: [Int + 86] (0) Manitowoc Crane Group - Beijing China (Sales, Parts & Service) Tel: [Int + 86] (0) Fax: [Int + 86] (0) Manitowoc Crane Group - Middle East (Sales) Tel: [Int + 971] (0) Fax: [Int + 971] (0) (Parts & Service) Tel: [Int + 973] (0) Fax: [Int + 973] (0) Distributed By: Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories, and may not include all standard equipment M Printed in USA Form No. RT5E Part No Manitowoc Crane Group 2007