OPERATOR'S MANUAL Expand-it Edger Attachment UT15518B

Transcription

1 OPERATOR'S MANUAL Expand-it Edger Attachment UT15518B TM Your new Expand-it Edger Attachment has been engineered and manufactured to a high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. To reduce the risk of injury, the user must read and understand the operator s manual. Thank you again for buying an Expand-it Accessory. SAVE THIS MANUAL FOR FUTURE REFERENCE

2 TABLE OF CONTENTS l Introduction... 2 l Safety Rules... 3 l Symbols... 4 l Unpacking... 5 l Features... 6 l Assembly... 7 l Operation... 8 l Maintenance l Warranty l Parts, Ordering, and Service...12 INTRODUCTION With the Expand-it Edger Attachment you can create a professionally landscaped look to your lawn. Just connect the Expand-it Edger Attachment to your attachment capable power head and edging around walkways, curbing, and other similar areas can be accomplished quickly. Safety, performance, and dependability have been given top priority in the design of this edger attachment making it easy to maintain and operate. Carefully read through this entire operator s manual before using your new Expand-it Edger Attachment. Pay close attention to the safety rules, warnings, and cautions. If you use your tool properly and only for its intended use, you will enjoy years of safe, reliable service. The operation of any tool can result in foreign objects being thrown into your eyes which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection that is marked to comply with ANSI Z87.1. Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved. 2

3 SAFETY RULES Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS GENERAL SAFETY RULES l For safe operation, read and understand all instructions before using the edger attachment. Follow all safety instructions. Failure to follow all safety instructions listed below, can result in serious personal injury. l Do not allow children or untrained individuals to use this unit. l Wear safety glasses or goggles that are marked to comply with ANSI Z87.1 standards and hearing protection when operating this unit. l Wear heavy long pants, boots, and gloves. Do not wear loose fitting clothing, short pants, jewelry of any kind, or go barefoot. l Secure long hair so it is above shoulder level to prevent entanglement in any moving parts. l Keep all bystanders, children, and pets at least 50 ft. (15 m ) away. l Do not operate this unit when you are tired, ill, or under the influence of alcohol, drugs, or medication. l Do not operate in poor lighting. l Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance or exposure to hot surfaces. l Keep all parts of your body away from any moving part. l Do not touch areas around the muffler or cylinder of the power head, these parts get hot from operation. Failure to do so could result in possible serious personal injury. l Always stop the engine and remove the spark plug wire before making any adjustments or repairs except for carburetor adjustments. l Inspect unit before each use for loose fasteners, damaged or missing parts. Correct before using the edger attachment. Failure to do so can cause serious injury. l Use only original manufacturer s replacement parts. Failure to do so, may cause poor performance, possible injury, and will void your warranty. l Do not, under any circumstance, use any attachment or accessory on this product, which was not provided with the product, or identified as appropriate for use with this product in the Operator s Manual. SPECIFIC SAFETY RULES FOR EDGER USE l Clear the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the edger blade. l Be sure all guards are properly and securely attached. l Replace dull or worn blade; do not attempt to sharpen. l Use this edger for edging along sidewalks, driveways, flower beds, and similar areas. Do not use for any other purpose. l Be thoroughly familiar with the controls. Know how to stop the unit and disengage the controls quickly. l Do not use edger in rain or wet locations. l Do not use the edger on or near graveled surfaces. l If the edger strikes any type of foreign object: 1. Stop the edger and disconnect the spark plug wire. 2. Inspect for damage to the edger attachment. 3. Correct damage before using the edger attachment. Failure to do so can cause serious injury. l Make yourself familiar with the area you are edging. Be aware of uneven sidewalks, holes in the terrain as well as other similar hazardous conditions. Always push the edger attachment slowly over rough ground. l Always stop the engine and remove the spark plug wire before installing attachments, or making any adjustments. 3

4 SYMBOLS Important: Some of the following symbols may be used on your unit. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Read Your Operator s Manual Wear eye and hearing protection. Indicates danger, warning or caution. It means attention!!! Your safety is involved. Your manual contains special messages to bring attention to potential safety concerns, machine damage as well as helpful operating and servicing information. Please read all the information carefully to avoid injury and machine damage. Wear eye protection which is marked to comply with ANSI Z87.1 as well as hearing protection when operating this equipment. Keep bystanders away. Keep all bystanders at least 50 ft. (15 m) away. Ricochet. Danger of Ricochet. Sharp blade. Danger - Keep hands and feet away from rotating blade. The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices that may cause property damage. NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment. SAVE THESE INSTRUCTIONS 4

5 UNPACKING INSTRUCTIONS We have shipped the Expand-it Edger Attachment completely assembled. l Carefully remove the tool from the box. Make sure that all items listed in the packing list are included. l Inspect the tool carefully to be sure no breakage or damage occurred during shipping. l Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. l If any parts are damaged or missing, please call chainsaw ( ). PACKING LIST Expand-it Edger Attachment (Completely Assembled) Hanger Cap Operator s Manual If any parts are missing, replace them before operating the tool. Failure to do so could result in serious personal injury. 5

6 FEATURES Before using the Expand-it Edger Attachment, familiarize yourself with all operating features and safety requirements. Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. EDGER ATTACHMENT SHAFT KNOB BLADE GUARD END CAP BLADE DEBRIS FLAP GEAR HEAD WHEEL Fig. 1 Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. 6

7 ASSEMBLY The edger attachment is fully assembled at the factory and requires no further assembly. JOINING THE POWER HEAD TO THE EDGER ATTACHMENT See Figure 2. Never attach or adjust any attachment while power head is running. Failure to stop the engine can cause serious personal injury. The edger attachment connects to the power head by means of a coupler device. 1. Loosen the knob on the coupler of the power head shaft and remove the end cap from the edger shaft. 2. Push in the button located on the edger attachment shaft. Align the button with the guide recess on the power head coupler and slide the two shafts together. Rotate the edger attachment shaft until the button locks into the positioning hole. NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place. 3. Tighten the knob securely. Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious injury. REMOVING THE ATTACHMENT FROM THE POWER HEAD For removing or changing the attachment: 1. Loosen the knob. 2. Push in the button and twist the shafts to remove and separate ends. POWER HEAD SHAFT GUIDE RECESS EDGER ATTACHMENT COUPLER KNOB POSITIONING HOLE Fig. 2 7

8 OPERATION Wear safety glasses or goggles when operating this tool. Failure to do so could result in possible serious injury. OPERATING THE EDGER See Figure 3. Hold the edger with the right hand on the rear handle and the left hand on the front handle. The edger should be held on the right side of the body. Keep a firm grip with both hands while in operation. The edger should be held at a comfortable position with the rear handle about hip height. Always operate the unit at full throttle. Prolonged cutting at partial throttle will result in oil dripping from the muffler. TO ADJUST THE BLADE DEPTH See Figures 4 and 5. Depth of the cut is determined by the distance from the bottom of the wheel to the tip of blade. 1. Stop the engine and disconnect the spark plug wire. 2. Loosen the adjusting knob and move the wheel arm up to increase the depth and down to decrease the depth. 3. After adjustment is complete, tighten the adjusting knob securely. NOTE: Adjust the blade depth from 1/2 in. to 1 in. (1.2 to 2.5 cm) deep initially. Make a shallow cut to test the cutting depth. If the cutting depth needs adjusting, this should be done progressively until the desired depth is reached. ADJUSTING KNOB TO INCREASE DEPTH WHEEL ARM TO DECREASE DEPTH Fig. 4 Fig. 3 CUTTING TIPS l The edger will edge along sidewalks, driveways, flower beds, curbs, and similar areas. l Use the arrow guide on the blade guard to align the blade with the edging surface. See Figure 3. l Cut at a steady pace. If the blade begins to bog down, you are edging too fast; slow your pace. Do not force the blade into ground. l Light contact of the blade against the sidewalk edge, curb, etc. is acceptable and will not damage the edger. l Best appearance is obtained when grass is dry. Avoid edging in wet soil or wet grass areas or the blade guard might clog and result in an uneven edge. If the blade guard becomes clogged, stop the engine, disconnect the spark plug wire, and remove debris from the blade guard. BLADE DEPTH CURB GUIDE BLADE Fig. 5 8

9 MAINTENANCE Use only original manufacturer's replacement parts, accessories and attachments. Failure to do so may cause poor performance, possible injury and may void your warranty. BLADE TURN BLADE NUT CLOCKWISE l Never operate a unit that is damaged, improperly adjusted, or is not completely and securely assembled. l Always stop the engine and remove the spark plug wire before making any adjustments or repairs. l Inspect the unit before each use for loose fasteners and damaged or missing parts. Replace any parts that are cracked, chipped, or damaged in any way. Failure to do so can cause serious injury. l Make sure all handles are properly and securely attached. l Never modify the unit in any way. Do not use for any job except that for which it is intended. l For service, contact a service dealer. You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer. BLADE REPLACEMENT See Figures 6 and 7. Replace blades that are damaged or worn. Stop the engine and disconnect the spark plug wire. Always make sure the blade is installed correctly and securely fastened before each use. 1. Place the holding pin through the slot in the upper flange washer and rest it against the bolt head of the blade guard. 2. Using a 1/2 inch socket wrench, turn the blade nut clockwise to loosen. 3. Remove the blade from the edger shaft. 4. Clean debris from the edger shaft and flange washers. 5. Center the blade on the upper flange washer making sure the blade sits flat. 6. Install the lower flange washer with the cupped hole away from the blade. 7. Install the blade nut onto the edger shaft. 8. Place the holding pin through the slot in the upper flange washer and rest it against bolt head of the blade guard. 9. Using a 1/2 inch socket wrench, turn the blade nut counterclockwise onto the edger shaft. Tighten securely. LOWER FLANGE WASHER BLADE TURN BLADE NUT COUNTERCLOCKWISE HOLDING PIN UPPER FLANGE WASHER Fig. 6 HOLDING PIN Fig. 7 9

10 MAINTENANCE MAINTENANCE STORING THE EDGER ATTACHMENT Store the edger attachment in a well ventilated place that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. To remove the edger attachment from the power head for storage: 1. Loosen the knob on the coupler device. 2. Push the button in, then twist the shafts to remove and separate the power head from the attachment. For storing information: Please refer to the operator s manual of your power head. ATTACHING THE STORAGE HANGER See Figure 8. There are two ways to hang your attachment for storage. l To use the hanger cap, push in the button and place the hanger cap over end of the edger attachment shaft. Slightly rotate the cap from side to side until the button locks into place. l The secondary hole in the edger attachment shaft can be used for hanging purposes as well. HANGER CAP SECONDARY HOLE BUTTON EDGER ATTACHMENT SHAFT HOUSING Fig. 8 10

11 WARRANTY LIMITED WARRANTY STATEMENT Homelite Consumer Product, Inc. warrants to the original retail purchaser that this Expand-it product is free from defect in material and workmanship and agrees to repair or replace, at Homelite Consumer Products, Inc. s discretion, any defective product free of charge within these time periods from the date of purchase. l One year for the following units: UT08110, UT20760, UT10901; l Two years for all other Homelite products, if the product is used for personal, family or household use; l 90 days, if any of the above products are used for product used for any other purpose, such as commercial or rental. This warranty extends to the original retail purchaser only and commences on the date of the original retial purchase. Any part of the Expand-it product manufactured or supplied by HOMELITE and found in the reasonable judgment of HOMELITE to be defective in material or workmanship will be repaired or replaced by an authorized service dealer without charge for parts and labor. The Expand-it product including any defective part must be returned to an authorized service dealer within the warranty period. The expense of delivering the Expand-it product to the dealer for warranty work and the expense of returning it back to the owner after repair or replacement will be paid for by the owner. HOMELITE S responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Expand-it product. Proof of purchase will be required by the dealer to substantiate any warranty claim. All warranty work must be performed by an authorized service dealer. This warranty is limited to ninety (90) days from the date of original retail purchase for any Expand-it product that is used for rental or commercial purposes, or any other income-producing purpose. This warranty does not cover any Expand-it product that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Expand-it operator s manual. This warranty does not apply to any damage to the Expand-it product that is the result of improper maintenance or to any Expand-it product that has been altered or modified so as to adversely affect the products operation, performance or durability or that has been altered or modified so as to change its intended use. The warranty does not extend to repairs made necessary by normal wear or by the use of parts or accessories which are either INCOMPATIBLE WITH THE Expandit product or adversely affect its operation, performance or durability. In addition, this warranty does not cover: A. Tune-ups Spark Plugs, Carburetor Adjustments, Filters B. Wear items Bump Knobs, Outer Spools, Cutting Lines, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts HOMELITE reserves the right to change or improve the design of any Expand-it product without assuming any obligation to modify any product previously manufactured. ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE STATED WARRANTY PERIOD. ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES INCLUDING MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN THEIR ENTIRETY AFTER THE EXPIRATION OF THE APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY DAY WARRANTY PERIOD. HOMELITE S OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY OTHER OBLIGATION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES INCLUDING, BUT NO LIMITED TO EXPENSE OF RETURNING THE HOMELITE PRODUCT TO AN AUTHORIZED SERVICE DEALER AND EXPENSE OF DELIVERING IT BACK TO THE OWNER, MECHANIC S TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES, RENTAL OF A LIKE PRODUCT DURING THE TIME WARRANTY SERVICE IS BEING PERFORMED, TRAVEL, LOSS OR DAMAGE TO PERSONAL PROPERLY, LOSS OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, OR INCONVENIENCE, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This warranty gives you specific legal rights, any you may also have other rights which vary from state to state. This warranty applies to all Expand-it products manufactured by HOMELITE and sold in the United States and Canada. To locate your nearest service dealer, dial or log on to our website at 11

12 OPERATOR'S MANUAL Expand-it Edger Attachment UT15518B TM SERVICE For parts or service, contact your nearest Expand-it authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call chainsaw ( ) or visit us online at REPAIR PARTS The model number of this tool is found on a plate or label attached to the housing. Please record the serial number in the space provided below. MODEL NUMBER UT15518B SERIAL NUMBER HOMELITE CONSUMER PRODUCTS, INC Pearman Dairy Road Anderson, SC Post Office Box 1207, Anderson, SC Phone chainsaw ( )