I hope this guide helps you as much as Boomer Bob helped me. We re just sharing what we know to help out other folks. Best of luck! Phil C.

Size: px
Start display at page:

Download "I hope this guide helps you as much as Boomer Bob helped me. We re just sharing what we know to help out other folks. Best of luck! Phil C."

Transcription

1 A brief tutorial on swapping cams for the Victory Cross Roads and Cross Country on the Victory Freedom 106 inch V-Twin Engine with 6 speed over drive transmission Disclaimer: Swapping cams on a Victory XR/XC is meant for those with some engine mechanical assembly/disassembly experience. Do not attempt this if you are unsure of your ability or lack the necessary tools or skill to complete the job. The steps outlined in this tutorial are not meant to be the definitive resource for performing a cam swap on a Victory 106 engine. Over the course of time, steps may be refined or deleted by those who have done these procedures. If you are unsure of any of the steps involved, consult the attached service manual pages, someone who has done the work, or a qualified Victory mechanic. The author takes no responsibility for any component failures, part malfunctions, engine malfunctions, or damage done to the engine or any of its components. You are doing this of your own free will and will hold harmless the author or any of its editors. You are being held responsible for your own work and have no one else to blame but yourself if things go wrong. I hope this guide helps you as much as Boomer Bob helped me. We re just sharing what we know to help out other folks. Best of luck! Phil C. Forward: Swapping cams on a Victory Freedom engine is the easiest and cheapest way to increase engine performance on the Victory XR/XC. This brief tutorial will outline the steps needed to do the job yourself with simple easy to follow instructions. Attached to this document are excerpts from the Victory XR/XC Service Manual that you will need to complete the job. Please read through this guide in its entirety and be sure you understand all the steps involved before attempting to swap cams.

2 Items Needed: The following tools and supplies will be needed to complete the cam swap: General Instructions: Your owner s manual Motorcycle jack Automotive Pry-bar Long, sturdy screwdriver or extra long 3/8th drive ratchet extension BFH (Big F n Hammer) and rubber mallet 3/8 inch drive ratchet ½ inch drive ratchet Torque wrench Assorted metric sockets for 3/8ths and ½ inch drive ratchets (8mm, 10mm, 12mm, 13mm, 15mm, 19mm) Assorted metric wrenches in the above stated sizes. Assorted Metric Allen Keys/ Hex Wrenches 1 1/16th inch wrench 1 1/16th socket Small tube of Engine Assembly Grease or Lube Small tube of Anti-seize Enough oil for an oil change and fresh filter Strong small magnet Several shop rags Place the motorcycle jack completely under the motorcycle engine and safely lift the motorcycle off the ground. You will need the front tire slightly off the ground so the frame can move without the bike s weight on it. Secure the motorcycle so it doesn t tip and fall while you are working on it. Disconnect the battery before you do any work! Disassembly Procedures Using your owner s manual, carefully follow the instructions that guide you to remove the side covers, seat, and fuel tank. When removing the fuel line from the tank, be sure to pinch the tabs which secure it to the tank. Do not forcefully pull it off! Remove the spark plug wires and spark plugs. Remove the oil dip stick and plug the hole with a shop rag. Ensure that the rear brake master cylinder cover is tight then remove the right side driver s floor board by removing the two 8mm Hex bolts that hold it on the sub frame. Remove the floor board and rear brake controls as an assembly. Do not disconnect the rear brake master cylinder or brake lines from the engine. Lean the floor board/brake assembly on the engine guard.

3 Note: Those of you with the flat cast engine guards will probably have to remove them to gain sufficient access to the engine. Those with the round tubular bars can leave them attached to the frame if you wish. THE KINDA SCARY PART: The front backbone of the Victory XR/XC can be split from the rear backbone to gain access to the engine without removing it. In this step we will split the back bone where it meets in the middle to gain access to the valve covers and give us enough room to remove the cams. At the rear of the engine you will notice that the engine is attached to the front backbone and rear backbone with what looks like 2 triangular pieces of steel. These are attached to both backbones with 4 bolts. 2 bolts are in the front backbone, 2 bolts are in the rear backbone. This is the rear engine mount.

4 Loosen the rear engine mount bolt that attaches directly to the rear of the engine. Do not remove it. There is a lot of friction holding the front backbone to rear backbone so you really don t need to worry about the backbone dropping down. Just in case, hold and secure your pry bar under the front backbone to prevent it from slipping in the next step. This is easily accomplished on the left side of the bike using the rear center of the engine mount as a pry point. Now remove the 2 bolts from the engine mount that are attached to the front backbone. These are near the rear engine opening. Do not loosen or remove the 2 bolts that hold the engine mount to the rear backbone. These are farthest from the rear engine opening. These will hold our engine in place while we perform our swap. With your pry-bar, lift up the backbone using the engine mount as a pry point. Lift it up enough to clear at least 1 bolt hole. While holding the front backbone up, insert your sturdy screwdriver or extra long 3/8ths ratchet extension into the lowest bolt hole to support the front backbone under the lower lip of the backbone. Lower the backbone onto the screwdriver/extension and remove your pry-bar. Not too scary now that you ve done it. Left Side View Right Side View Before you do anything else wipe off the tops of the valve covers with a shop rag to remove any dirt or debris that has accumulated on them. Then continue wiping down the right side of the engine to remove any debris. This is done so no foreign objects have the chance to get into the engine. Remove the 10 bolts from the top of each valve cover. Carefully lift and remove the valve cover and valve cover gasket from the right side of the engine. You do not have to remove the fuel injector plugs or harness. From this point on, I will be referring to Service Manual pages for disassembly and assembly. Not all steps will need to be followed in the service manual! I will indicate this in the instructions. All required Service Manual pages should be included in this write up. Follow the disassembly instructions in the service manual for the camshaft drive cover and cam chain tensioner (pg 7.8).

5

6 Follow the disassembly instructions in the service manual for the camshaft chain and sprocket removal (pg 7.10) Note: You will need the 1 1/16ths socket to turn the crank. Turn it carefully so you don t mar the alignment key. You do not have to bring the engine to TDC to remove the sprocket. Just turn the crank and remove the sprocket bolts as they come clear. You also do not need to remove any cam tensioner blade bolts. Removing the cam tensioner will give you enough slack to remove the cam sprocket. When you remove the sprocket, hold the chain to prevent it from falling into the head. I used a loose zip tie to hold the chain out of my way. I loosely secured the zip tie to a frame point. Do the same for the other cam sprocket removal.

7 Once the sprocket is removed you need to remove the black button cap bolt that is on top of the cam carrier. Once removed, take a hex wrench and attach a magnet to it. Insert this into the hole where the black button cap resided. Slowly and carefully remove the pin that is in there. Remove the cam carrier by loosening the 4 head nuts a half turn each until finger loose. Loosen them in a criss-cross pattern to relieve the valve spring tension equally! (pg 7.11) (do not disassemble the cam carrier any farther! We need to leave the rocker arms and rocker arm shafts in place!)

8 Turn the cam shaft so the alignment mark points up. Carefully lift and tilt the cam carrier so the cam can be removed without removing the carrier. Push the spring side portion of the rocker arms down so the cam may be removed. Remove the cam. Now do the other cam carrier.

9 Assembly Procedures Remove the new cams from the packaging and liberally spray them with brake cleaner. This will remove any oil or metal shavings that are on them. Let the cams air dry after they are clean. Note that each cam is marked whether it is for the Front or Rear with either an F or an R. Once dry, liberally coat the cam lobes and cam bearing surfaces with assembly grease. If it s machined smooth, it ll need Engine Assembly grease. Pages 7.21 through 7-26 of the Service manual are the assembly process. Follow it exactly or you will damage an engine component! Double check each step made or risk damaging your engine! I cannot stress that enough! If a part or a bolt wasn t removed, skip that section. There are alignment holes that determine TDC (Top Dead Center). If you look at the Service manual drawing, they are located under and to the left or right of the crankshaft snout. You can use a 7mm hex wrench to align them.

10

11

12

13

14

15

16 Once you re sure of your work, it s time to button up the engine. Once you put on the valve covers, it s the perfect time to add the fuel injector connections of your fuel controller. You only need to make the connections to the injectors at this time. You can leave the rest until you finished the engine and backbone assembly. Once you re ready to reassemble the backbone you may need to relocate your sturdy screwdriver. Place another screwdriver in the upper hole so you can access the lower lip to lift the backbone again. Remove the lower screwdriver, lift the backbone with the prybar, remove the top screwdriver, then lower the backbone into place. If you have a hard time getting the back bone to go down, place the rubber mallet on the top rear of the backbone and hold it there. Take your BFH and hit the top of rubber mallet until you get both holes aligned. Aren t you done yet? Come on it s almost beer 30! If you added a fuel controller, finish the install according to the manufacturer s instructions. Put your tank, seat, side covers, plugs and plug wires back on then reconnect the battery. A word before you fire it up. Each cam manufacturer has a specified break in procedure. Follow it. LLoydz recommends his cams be broken in by regular driving. Make sure you have a base line setting for your fuel controller before you fire it up. Search the forums and the web to get an idea of what you want. Go ahead and fire it up!

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13. Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961

More information

Though Indian s 111-cubic-inch engine delivers a

Though Indian s 111-cubic-inch engine delivers a TECH by Chris Maida Andrews Indian 111 Camshafts Part I: Removing the cams from the camshaft compartment Tools Needed Red Loctite Clean rags 6mm Allen 5/64" Allen 3/32" punch External circlip pliers Needlenose

More information

Z8004. KDT916 S197 Performance Watts Linkage

Z8004. KDT916 S197 Performance Watts Linkage Z8004 KDT916 S197 Performance Watts Linkage Kit Includes: Differential Cover o Magnetic Plug o Standard Plug o Main Brace o Center Pivot o Swivel Foot Bolts 2 o Swivel Foot Retaining nuts 2 o M12x30 Bolt

More information

Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

How to install the Barnett clutch and the stronger Oil Pump Drive Gear

How to install the Barnett clutch and the stronger Oil Pump Drive Gear How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

1999 Corolla Valve Cover Gasket Replacement

1999 Corolla Valve Cover Gasket Replacement 1999 Corolla Valve Cover Gasket Replacement While checking the spark plugs on my 1999 Corolla, I found the each plug sitting in a pool of oil. Oil on the spark plugs usually is indicative of major engine

More information

This document provides instructions for removing and installing a Front Wheel / Rotor on a Ducati Superbike. The torque values used are for the 748/916/996 from 1994 to 2001 and may be applicable for later

More information

Required tools are: Parts list:

Required tools are: Parts list: BEW cam and lifters replacement procedure by zanzabar Jay Roberts, Petaluma, CA. (modified from engine timing belt replacement procedure from MOGolf as demonstrated on a 2004 Jetta). Required tools are:

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough

More information

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions

Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped

More information

PORSCHE V r Valve Timing Instructions. Copyright 2009 Written by Mike Frye Edited my Adam G.

PORSCHE V r Valve Timing Instructions. Copyright 2009 Written by Mike Frye Edited my Adam G. PORSCHE 928 32V r Valve Timing Instructions Copyright 2009 Written by Mike Frye Edited my Adam G. Sections: Overview.3 Disclaimer/warnings/things to watch for 4 Terms and naming conventions used in this

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough

More information

Door Panel Removal & Window Stop Adjustment

Door Panel Removal & Window Stop Adjustment Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to

More information

How I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.

How I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B. How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By

More information

E31 Repair Procedure Replace Front Wheel Hub/Bearing Assembly

E31 Repair Procedure Replace Front Wheel Hub/Bearing Assembly E31 Repair Procedure 31-21 Replace Front Wheel Hub/Bearing Assembly Disclaimer This repair procedure is provided as is and is not authoritative with respect to any BMW repair operation. Mark F. Fling is

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

Suzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions

Suzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions Suzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related

More information

COBB CAMSHAFTS INSTALLATION Impreza RS/TS

COBB CAMSHAFTS INSTALLATION Impreza RS/TS 4673 South Cherry St. Salt Lake City, UT 84213 USA +1 801-713-0035 COBB CAMSHAFTS INSTALLATION 99-01 Impreza RS/TS Congratulations on your purchase of Cobb Camshafts. The following instructions should

More information

Slave Cylinder Weep Hole Drilling Procedure

Slave Cylinder Weep Hole Drilling Procedure Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key

More information

Tri-Spark Ignition System Installation Triple Cylinder TRI-0001

Tri-Spark Ignition System Installation Triple Cylinder TRI-0001 Tri-Spark Ignition System Installation Triple Cylinder TRI-0001 There are potentially lethal high voltages produced at the ignition coils and spark plugs, therefore every precaution must be taken to prevent

More information

For all Ram x4 Trucks, and all Ram x4 trucks.

For all Ram x4 Trucks, and all Ram x4 trucks. Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0907 APPLICATION: 2011-12 E90 335i/xi (N55 engine) with BMW M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

Mirrored from:

Mirrored from: Mirrored from: http://www.wranglerforum.com/f274/install-synergy-suspension-ball-joints-write-up-147062.html 03-18-2012, 02:43 AM #1 SilverSport Supporting Member WF Supporting Member Install Synergy Suspension

More information

Changing the Struts on a WK Jeep CRD

Changing the Struts on a WK Jeep CRD Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading

More information

W hen Harley-Davidson introduced the 96 Twin Cam Motor in 2007, the increased displacement was obtained by

W hen Harley-Davidson introduced the 96 Twin Cam Motor in 2007, the increased displacement was obtained by Revolution Performance Story by Jason Mook Photos by Jesse B. Nelson W hen Harley-Davidson introduced the 96 Twin Cam Motor in 2007, the increased displacement was obtained by increasing the stroke of

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit

M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure

More information

Eurocompulsion Camshaft Installation

Eurocompulsion Camshaft Installation Eurocompulsion Camshaft Installation Introduction, please read. The purpose of this article is too assist our customers with installation of a performance camshaft in the Fiat Multiair 1.4 Turbo. The operation

More information

How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg

How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,

More information

Installing Rear Brake Pads on a WK Jeep

Installing Rear Brake Pads on a WK Jeep Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after

More information

What s in your new header system kit?

What s in your new header system kit? !"#$% "#$%& ' "())' **+ Congratulations on your purchase of the Dynatech / SuperMaXX system for the Dodge Magnum / Chrysler 300C. We believe, and think you will agree that this system is second to none

More information

2001 V70 T5 ETM Removal and Cleaning Directions

2001 V70 T5 ETM Removal and Cleaning Directions 2001 V70 T5 ETM Removal and Cleaning Directions Howard Cheng howardc64@gmail.com 10/24/05 Version 1.4 Read this before you start I performed this ETM cleaning because I had gotten 2 reduced performance

More information

Installation Instructions

Installation Instructions Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.

More information

Installation Instructions Truckin Suspension 6.5 Suspension Lift Kit DODGE DAKOTA-DURANGO (worm and sector)

Installation Instructions Truckin Suspension 6.5 Suspension Lift Kit DODGE DAKOTA-DURANGO (worm and sector) Installation Instructions Truckin Suspension 6.5 Suspension Lift Kit 1997-1999 DODGE DAKOTA-DURANGO (worm and sector) Important! Read all instructions before attempting any work on the vehicle. DO NOT

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

You will be removing the suspension of your vehicle. If you are not comfortable with this or do not have the proper tools, please do not proceed.

You will be removing the suspension of your vehicle. If you are not comfortable with this or do not have the proper tools, please do not proceed. Thank you for purchasing the CorkSport Mazda 3 and Mazdaspeed 3 Coilover Kit. This suspension system features 15-way adjustable dampening settings and full length adjustment to meet every driver s handling

More information

DIY: Shiver Valve Check, Illustrated

DIY: Shiver Valve Check, Illustrated DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover

More information

Slingshot Rotrex Supercharger Kit

Slingshot Rotrex Supercharger Kit Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you

More information

ENG-14, Balance Shaft Oil Seal Replacement

ENG-14, Balance Shaft Oil Seal Replacement ENG-14, Balance Shaft Oil Seal Replacement Introduction The following procedure will provide instructions for replacing the balance shaft seals on a 944. It will also provide instructions for resealing

More information

Service Bulletin Cylinder Head Service. September 17, 2002

Service Bulletin Cylinder Head Service. September 17, 2002 Service Bulletin 02-047 Applies To: 1998 02 Passport ALL September 17, 2002 Cylinder Head Service BACKGROUND In the 1998 through 2002 Passport Service Manuals, some of the information on cylinder head

More information

Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions

Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions The below installation instructions work for the following products: Steeda Sport Mustang Lowering Springs (2005+) Please read

More information

Peg-Harness installation instructions

Peg-Harness installation instructions Peg-Harness installation instructions I know it s not the easiest thing to do, but PLEASE READ THESE INSTRUCTIONS COMPLETELY so you will understand what you are trying to accomplish before you start drilling

More information

VWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version)

VWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version) VWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version) Click here to print this topic. Post Title: DIY: Timing Belt And Coolant

More information

Engine Management System

Engine Management System Engine Management System 6 0 4-0 0 1 I N S T R U C T I O N S For 2005-2010 Harley-Davidson FXS (Softail) Models 2 Revolution Performance was founded with two major goals in mind to go that extra mile providing

More information

Ford Focus Zetec SVT Timing Belt

Ford Focus Zetec SVT Timing Belt 2000-2004 Ford Focus Zetec SVT Timing Belt Replacement This guide will show you how to replace the timing belt on the 2.0L DOHC Zetec with VCT on a 2002 Ford Focus SVT. This is an interference motor. Written

More information

ST 93 RIPPER INSTALL KIT

ST 93 RIPPER INSTALL KIT ST 93 RIPPER INSTALL KIT P/N 2883777;2883778;2883779 APPLICATION The Timbersled Ripper ST93 Install Kit is designed to fit all Timbersled ST90 and ST93 Ripper models. This includes; Timbersled Model No.

More information

Saab 9-3 Krona Downpipe Installation Instructions. What's Included:

Saab 9-3 Krona Downpipe Installation Instructions. What's Included: www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo

More information

CAT-BACK EXHAUST FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE WARNING PARTS INCLUDED INSTALL PROCEDURE TOOLS NEEDED

CAT-BACK EXHAUST FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE WARNING PARTS INCLUDED INSTALL PROCEDURE TOOLS NEEDED PARTS LIST AND PARTS INCLUDED 1PC STAINLESS STEEL RESONATED MIDPIPE W/ 2-BOLT FLANGE 1PC STAINLESS STEEL MIDPIPE-TO-REAR MUFFLER SECTION 1PC STAINLESS STEEL REAR MUFFLER SECTION 1PC 3" DUAL OFFSET TIPS

More information

ACURA NSX ABS/ALB Modulator Rebuild Procedure

ACURA NSX ABS/ALB Modulator Rebuild Procedure Version 03 ACURA NSX ABS/ALB Modulator Rebuild Procedure I rebuilt my 1991 ABS/ALB modulator using this procedure. Please note that this will not guarantee that your ABS/ALB system issues will be resolved

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation

More information

CHASSIS CONTENTS EXTERIOR PARTS 7-1 FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-13 FRONT FORK 7-15 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30

CHASSIS CONTENTS EXTERIOR PARTS 7-1 FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-13 FRONT FORK 7-15 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30 CHASSIS CONTENTS EXTERIOR PARTS 7- FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-3 FRONT FORK 7-5 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30 REAR SHOCK ABSORBER 7-32 SWING ARM 7-33 7 7- CHASSIS EXTERIOR

More information

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and

More information

Copper Sleeve, Unit Injector, Replacement

Copper Sleeve, Unit Injector, Replacement Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks

More information

Our goal is to make the install a breeze. Please read the entire guide before beginning.

Our goal is to make the install a breeze. Please read the entire guide before beginning. www.airkewld.com Page 1 of 6 IRS Axle Kit Install IRS Axle Kit Install Our goal is to make the install a breeze. Please read the entire guide before beginning. KITS SHOULD INCLUDE 2 - Control-arm mounting

More information

Sherco Engine Teardown and Assembly Manual

Sherco Engine Teardown and Assembly Manual Sherco Engine Teardown This Manual is provided as a guide for: Removing the engine from the frame Splitting the cases Complete Disassembly of the engine Reassembly of the engine Reinstallation back in

More information

Engine Management System

Engine Management System Engine Management System 6 0 4-0 0 1 I N S T R U C T I O N S For 2005-2007 Harley-Davidson FL Models 2 Revolution Performance was founded with two major goals in mind to go that extra mile providing a

More information

Chrysler A-Body Tubular A-Arms Installation Instructions A-ARM INSTALLATION

Chrysler A-Body Tubular A-Arms Installation Instructions A-ARM INSTALLATION 1967-1976 Dodge Demon 1112 67-72 Chrysler A-Body Tubular A-Arms Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your A-Arm set was designed with the performance

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350: TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: 2007 2008 IS 350: 2006 2008 I. OPERATION FLOWCHART Verify Vehicle Eligibility 1. Check the VIN range. 2.

More information

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6) Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

Torqueflite Manual/Automatic Valve Body

Torqueflite Manual/Automatic Valve Body TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts

More information

PORSCHE 928. PKT Installation 1.8. No air pump version. Air pump version

PORSCHE 928. PKT Installation 1.8. No air pump version. Air pump version PORSCHE 928 PKT Installation No air pump version Air pump version 1.8 Tools Torque wrench 10mm socket 12mm socket 13mm socket 5mm allen socket 6mm allen socket 8mm allen key Caliper Supplies Blue Loctite

More information

RAMPAGE POWER LIFT RAMP

RAMPAGE POWER LIFT RAMP RAMPAGE POWER LIFT RAMP INSTALLATION AND OPERATING INSTRUCTIONS (3/10/07) The Rampage Power Lift Ramp is the fast, easy, and safe way to load a motorcycle into a truck. One person can load or unload a

More information

Precision Degree Wheel Kit

Precision Degree Wheel Kit 555-81621 Precision Degree Wheel Kit Instruction Booklet Instructions for 81621 Camshaft Degree Kit Thank you for purchasing the Jegs Camshaft Degree Kit. Please follow these detailed instructions to properly

More information

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Product: Variable Height Spring. Part Numbers: N. Applications: BMW F8x, M2/M3/M

Product: Variable Height Spring. Part Numbers: N. Applications: BMW F8x, M2/M3/M Product: Variable Height Spring Part Numbers: 415-503001-N Applications: BMW F8x, M2/M3/M4 2014-17 Contents in the box: Qty Part # Description 1 00P-0A1646-B Front Passenger Sleeve Assembly 1 00P-0A1645-N

More information

HOW TO INSTALL FORD RACING HOT ROD PERFORMANCE CAMSHAFTS MUSTANG GT

HOW TO INSTALL FORD RACING HOT ROD PERFORMANCE CAMSHAFTS MUSTANG GT HOW TO INSTALL FORD RACING HOT ROD PERFORMANCE CAMSHAFTS 2005-2010 MUSTANG GT INSTALLATION TIME: 8 HOURS Introduction: This instruction set is intended to be a step by step guide for installing Ford Racing

More information

Volkswagen Cabriolet DIY Guide Engine & Transmission Mounts

Volkswagen Cabriolet DIY Guide Engine & Transmission Mounts Volkswagen Cabriolet DIY Guide Engine & Transmission Mounts Component Front carrier (bracket) Part Numbers 171199329F Transmission/ Engine All (Automatic version is NLA) Photo Front carrier flange 171199319A

More information

Mustang Differential Gears - Installation Instructions

Mustang Differential Gears - Installation Instructions Mustang Differential Gears - Installation Instructions The below installation instructions work for the following products: Ford Racing Gears - 3.73 Gears for 8.8" Ford Rear End Ford Racing Gears - FRPP

More information

BEFORE BEGINNING INSTALLATION

BEFORE BEGINNING INSTALLATION COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

List of tools: Jack Two Jack Stands Conventional Socket Set Liquid Collection pan Rear axle lubricant and friction modifier Rags for wiping up spills

List of tools: Jack Two Jack Stands Conventional Socket Set Liquid Collection pan Rear axle lubricant and friction modifier Rags for wiping up spills List of tools: Jack Two Jack Stands Conventional Socket Set Liquid Collection pan Rear axle lubricant and friction modifier Rags for wiping up spills 1. Jack car up Loosen wheel lugs first. Don t take

More information

Appendix B A Step-by-Step Guide to Changing the Front Oil Seals on the Volvo B-230 Engine

Appendix B A Step-by-Step Guide to Changing the Front Oil Seals on the Volvo B-230 Engine Appendix B A Step-by-Step Guide to Changing the Front Oil Seals on the Volvo B-230 Engine When replacing the timing belt, check to see that there are no oil leaks around any of the pulleys. If no leaks,

More information

Honda Super Cub Etc. Frame & Forks

Honda Super Cub Etc. Frame & Forks Honda Super Cub Etc. Frame & Forks Introduction This section is all about how to strip, servioce and rebuild the frame and forks of the Honda Super Cub and other bikes using the same frames, plus all the

More information

The M7 Direct Flow Intercooler (DFIC) Installation Guide

The M7 Direct Flow Intercooler (DFIC) Installation Guide The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting

More information

Timing Belt: Service and Repair

Timing Belt: Service and Repair 2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata

More information

The following information is gathered from pages of the Honda Aero Shop Manual.

The following information is gathered from pages of the Honda Aero Shop Manual. Original write-up by W. Boyter The following information is gathered from pages 3.10-3.12 of the Honda Aero Shop Manual. First of all, pull all your spark plugs, make sure your transmission is in neutral.

More information

Audi A3 2.0 T FSI Fuel Pump

Audi A3 2.0 T FSI Fuel Pump Installation Procedures Audi A3 2.0 T FSI Fuel Pump Cam Follower Replacement Kit ES2609354 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe,

More information

A Division of Thiessen Products, Inc.

A Division of Thiessen Products, Inc. The JIMS FORCEFLOW CYLINDER HEAD COOLER is designed for Twin Cam Models 1999 to present. Also fits all JIMS Twin Cam Race Engines. NOTE: These instructions show the installation of this product on a 2012

More information

Thanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT!

Thanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT! Thanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the Adjustable Lowering kit on your Honda

More information

Remove Air Cleaner Cover and. Filter

Remove Air Cleaner Cover and. Filter Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove

More information

Do not have any open flame or heat sources close to the installation

Do not have any open flame or heat sources close to the installation March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew

More information

-Magnet (not completely necessary but can come in handy)

-Magnet (not completely necessary but can come in handy) McLeod High Performance Hydraulic Clutch Line Upgrade (05-14 V8) Included in kit: -New clutch line -2 fittings Required Tools: -Floor jack and jack stands (or a lift) -Flashlight -Angled pick tool -13mm

More information

LUGGAGE RACK MG TD with Original Steel Wheels. Installation Instructions. Step 1

LUGGAGE RACK MG TD with Original Steel Wheels. Installation Instructions. Step 1 Created on 7/7/2003 8:34:00 PM by Michael Grant Last Revised 2/2/2008 1:55:00 PM Page 1 of 14 1 2 3 243-705 LUGGAGE RACK MG TD with Original Steel Wheels If your TD has been converted to wire wheels, please

More information

Light Truck MegaShifter

Light Truck MegaShifter Installation Instructions Light Truck MegaShifter The B&M Light Truck Megashifter shifter is designed to be used in most light trucks equipped with most popular three speed or four speed automatic transmissions.

More information

Front Axle Pinion Seal Replacement

Front Axle Pinion Seal Replacement Front Axle Pinion Seal Replacement by Flopster843 10 Apr 2016 The AAM 925 axle used on the front of Dodge Ram trucks is a decent unit, but it does have its flaws. This axle lacks lockout hubs on the front

More information

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION

More information

Audi A Timing Belt. Installation

Audi A Timing Belt. Installation Audi A3 2.0T Timing Belt Installation ES2538517 Audi A3 2.0 Timing Belt Installation This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may

More information

Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.

Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible

More information

Volvo 850 Radiator Replacement Jason Reed 29 March 2013

Volvo 850 Radiator Replacement Jason Reed 29 March 2013 This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS PERFORMER RPM CAMSHAFT / LIFTERS / LUBE KIT For 343-401 c.i.d. AMC V8 Engines CATALOG # 7132 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most

More information

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117 Page 1 PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 283-400 c.i.d. Chevrolet V8 Engines GENERAL INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

The spacers can be made out of.750 round aluminum bar with a.3125 to.318 hole drilled in center.

The spacers can be made out of.750 round aluminum bar with a.3125 to.318 hole drilled in center. SECTION I : FRONT COVER INSTALLATION With Crankshaft, Camshaft and oil Galley plugs installed in engine, you need to verify that the front cover clears the oil galley plugs and fits on engine block. The

More information

Wheel Bearing Replacement Passat TDI

Wheel Bearing Replacement Passat TDI Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information