INSTRUCTION MANUAL MARTINDALE CM52 CLAMP METER. ELECTRIC Trusted by professionals. Other products from Martindale:
|
|
- Leon Shepherd
- 5 years ago
- Views:
Transcription
1 Other products from Martindale: 18th Edition Testers All-in-one s Calibration Equipment Continuity Testers Electrician s Kits Full Calibration & Repair Service Fuse Finders Digital Clamp Meters Digital Multimeters Microwave Leakage Detectors Motor Maintenance Equipment Non-trip Loop Testers Pat Testers & Accessories Phase Rotation Units Proving Units Socket Testers Thermometers & Probes Test Leads Voltage Indicators Specialist Drummond Testers Specialist Metrohm Testers (4 & 5kV) CM52 CLAMP METER INSTRUCTION MANUAL Martindale Electric Company Limited Metrohm House, Imperial Park, Imperial Way, Watford, Hertfordshire, WD24 4PP, UK Tel: +44(0) Fax: +44 (0) sales@martindale-electric.co.uk Website: Martindale Electric Company Ltd Registered in England No Rev 1. MARTINDALE ELECTRIC Trusted by professionals
2 SAFETY INFORMATION: Always read before proceeding WARNING Read through and understand the instructions contained in this manual before using the instrument. Keep the manual handy for quick reference whenever necessary. Be sure to use the instrument for its intended applications only and to follow measurement procedures described in the manual. Be sure to understand and follow all safety instructions contained in the manual. Failure to follow the above instructions may cause injury, instrument damage and/or damage to equipment under test. Operating Environment: Jaw opening: Safety Standard: Power Source: Accessories: Dimension: Weight: 0-40 C, relative humidity up to 75% (without condensation) Approx. 21mm EN CAT II 600V Two LR-44(3V) or SR-44 batteries Instruction manual, two LR-44 batteries (installed in meter) carrying case. 145L x 54W x 26D (mm) Approx. 70g (batteries included) Updated instructions and product information are available at: SYMBOLS: ~ Equipment complies with relevant EU Directives AC (Alternating Current) Equipment protected by Double Insulation (Class II) Caution - refer to accompanying documents End of life disposal of this equipment should be in accordance with relevant EU Directives Accuracy At 23 C ± 5 C RH 75% less Ranges Accuracy Frequency AC 2A AC 20A AC 200A 0.05<2A ±2%rdg ± 8dgt 0.5<20A ±2%rdg ± 5dgt 0.5<20A ±3%rdg ± 10dgt 5A<200A ±2%rdg ± 5dgt 5A<200A ±3%rdg ± 10dgt 50/60Hz 50/60Hz 45Hz~1KHz 50/60Hz 45Hz~1KHz
3 MARTINDALE ELECTRIC Display: Measuring Range: Low Battery Indication: Over-range Indication: Response Time: Auto Power-Off: Data Hold: Storage Environment: Altitude: Specification CM52 Clamp Meter 3.5 digit LCD 0.001A - 200A Symbol appears on the display "OL" flashes on the highest digit Approx. 3 times per second The instrument automatically shuts off approx. 30 minutes after being turned on. For all ranges -10 C to +50 C, relative humidity up to 75% (without condensation) 2000 metres CONTENTS 1 Introduction Description Unpacking and Inspection Replacing the batteries 3 2 Safety Warnings 3 3 Operation 4 4 Maintenance Cleaning Repair & Service Storage Conditions Warranty 6 Technical Specification 7 Pollution Degree: 2
4 1. INTRODUCTION This manual contains information and warnings which must be followed to ensure safe operation of the clamp meter. WARNING READ "SAFETY INFORMATION" BEFORE USING THE METER This instrument is a pocket-sized AC clamp meter. The clamp incorporates teardrop shaped jaws for ease of use in crowded cable areas and other tight places. The CM52 is designed to international safety standard EN (CAT II 600V) and has a wide range frequency response from 45Hz~1KHz. The clamp also incorporates a Data Hold function to allow for easy readings in tight or hard-to-read locations and an auto power-off function to conserve battery power. A protective carrying case is included for protection of the meter whilst not in use. 4. MAINTENANCE Maintenance consists of periodic cleaning and battery replacement. Repairs or servicing not covered in this manual should only be performed by qualified personnel. 4.1 Cleaning The CM52 may be cleaned using a soft damp cloth. Do not use abrasives, solvents, or detergents, which can be conductive. Allow to dry completely before using. 4.2 Repair & Service There are no user-serviceable parts in this unit. Return to Martindale Electric Company Ltd if faulty, the service department will quote promptly to repair any fault that occurs outside the guarantee period. Before the unit is returned, please ensure that it has been checked thoroughly for flat batteries (check & replace). 1.1 Description 1 CAT. II MA X Storage Conditions The clamp meter should be kept in warm dry conditions away from direct sources of heat or sunlight, and in such a manner as to preserve the working life of the unit. It is strongly advised that the unit is not kept in a tool box where other tools may damage it. 0 0V ~ 2 200A OFF ~ 0A 0 3 HOLD 2A 20A Warranty The CM52 is guaranteed against faults in manufacture and materials for 24 months from date of invoice. Faults will be rectified free of charge provided the unit has not been tampered with and is returned with its housing unopened. Damage due to dropping, abuse or misuse is not covered by this guarantee. Batteries are not covered by this guarantee. 3 CM52 DIGITAL CLAMP METER 1 6
5 AC Current Measurement 1. Set the range switch to 2A / 20A / 200A range. 2. Press the yellow trigger to open the jaws and clamp on to one conductor only. Try to place the conductor at the centre of the jaws. 1. Clamp Jaws Detect AC current flowing through the conductor on test. 2. Trigger Press the trigger to open the clamp jaws. When the trigger is released, the jaws will close. 3. Display The display indicates the measured value of signal, function mode, low battery, range and hold settings. 4. Hold Button Press to toggle in and out of data hold mode. In the data hold mode, the "HOLD" indicator is displayed and the last reading is frozen on the display. Press the button again to exit and resume taking readings. Using Data Hold Function 1. Press the Data Hold button to freeze the reading. Symbol " H " is displayed to indicate the instrument is being used in the Data Hold mode. 2. Press the button again to cancel the Data Hold mode. The Data Hold function is available on all ranges for measurement in hard-to-read locations. 5. Function / Range selector rotary switch. The rotary switch selects the function and desired range. 1.2 Unpacking and Inspection Before unpacking the clamp meter, examine the shipping carton for any sign of damage. Unpack and inspect the clamp meter and if there is any damage then consult your distributor immediately. After removing your new clamp meter from its packaging, you should have the following items: 1. Digital clamp meter 2. Instruction manual 3. Two LR-44 batteries (installed in meter) 4. Carrying case If any of the above items are missing or are received damaged, please contact the distributor from whom you purchased the unit. 5 2
6 1.3 Replacing the batteries DANGER Never replace the batteries while taking a reading. When the display remains blank or the symbol appears, replace the batteries. 3. OPERATION 1. Set the range switch to any range. 2. If the display remains blank or symbol appears, replace the batteries in accordance with the battery replacement procedures as outlined in section Set the range switch to the OFF position. 2. Remove the screw on the back of the case. 3. Replace the batteries with two new ones, observing correct polarity. Replacement batteries should be type LR-44 or SR Re-install the screw in the case bottom. 2. SAFETY WARNINGS This instrument has been designed and tested according to EN , Safety Requirements for Electronic Measuring Apparatus. This instruction manual contains warnings and safety rules which must be observed by the user to ensure safe operation of the instrument. Therefore, read through these operating instructions before using the instrument. DANGER Never use the instrument on a circuit above 600V AC. The jaws are made of metal and their tips are not insulated. Be especially careful about the hazard of possible shorting where equipment under test has exposed conductive parts. CAUTION The maximum size conductor that can be tested is approx. 21mm in diameter. An accurate measurement cannot be made when the jaws are not fully closed on a conductor larger than 21mm. When measuring a large current, the jaws may buzz. This is not a fault and does not affect the accuracy. About 30 minutes after the instrument is turned on, the Auto Power-Off function turns the instrument off, even during a measurement. To continue testing, turn the range switch to OFF, then to a range again. Do not attempt to take measurements with the battery compartment cover removed from the instrument. 3 4
MARTINDALE INSTRUCTIONS ELITE FUSE FINDER KIT ELECTRIC. Trusted by professionals. 4.4 Storage Conditions
4.4 Storage Conditions The FD650/R and FD500/T or FD600/T should be kept in warm dry conditions away from direct sources of heat or sunlight, with the battery removed and in such a manner as to preserve
More informationINSTRUCTION MANUAL CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT
CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER INSTRUCTION MANUAL 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT These instructions contain both information and warnings
More informationINSTRUCTION MANUAL CM69 TRMS AC EARTH LEAKAGE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT
CM69 TRMS AC EARTH LEAKAGE CLAMP METER INSTRUCTION MANUAL 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT These instructions contain both information and warnings
More informationInstruction Manual PC104/PC105 3-PHASE SOCKET TESTER. Check out what else you can get from Martindale:
Check out what else you can get from Martindale: 17th Edition Testers Accessories Calibration Equipment Continuity Testers Electricians Kits Environmental Products Full Calibration & Repair Service Fuse
More informationINSTRUCTION MANUAL DT173 DT175 DIGITAL THERMOMETERS ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING
DIGITAL THERMOMETERS INSTRUCTION MANUAL ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING Thank you for buying one of our products. For safety and a full understanding of its benefits please read this manual
More informationInstruction Manual VT4 VOLTAGE TESTER. Check out what else you can get from Martindale:
Check out what else you can get from Martindale: 17th Edition Testers Accessories Calibration Equipment Continuity Testers Electricians Kits Environmental Products Full Calibration & Repair Service Fuse
More informationSafety design conforming to the following provisions
Safety design conforming to the following provisions of IEC61010. Overvoltage category III 300V AC, pollution degree 2 Overvoltage category II 600V AC/DC, pollution degree 2 Protected throughout by double
More informationSafety design conforming to the following provisions
Safety design conforming to the following provisions of IEC61010. Overvoltage category III 300V, pollution degree 2, Overvoltage category II 600V, pollution degree 2, Data hold switch for easy reading
More informationInstruction Manual VT25 / VT28 VOLTAGE TESTER ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING
VT25 / VT28 VOLTAGE TESTER Instruction Manual ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING Thank you for buying one of our products. For safety and full understanding of its benefi ts please read this
More informationSL101 Manual_SL101 User Manual 05/10/ :06 Page 1. Instruction Manual
SL101 Manual_SL101 User Manual 05/10/2011 11:06 Page 1 SL101 Solar Power Irradiance Meter Instruction Manual Please read this manual before switching the unit on. Important safety information 1 inside.
More informationThe insulation tester must only be used by a skilled and competent measuring equipment connected directly to utilization points
IN2101 / IN2102 INSULATION TESTER INSTRUCTION MANUAL ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING Thank you for buying one of our products. For safety and a full understanding of its benefits please
More informationoperating manual DL7 101 DIGITAL THERMOMETER
operating manual DL7 101 DIGITAL THERMOMETER Safety Information This instrument is a portable 3½ digit., compact-sized digital thermometer designed to use external K-type thermocouple as temperature sensor.
More informationMetrohm E3640 FLASH TESTER INSTRUCTION MANUAL. Martindale Electric Co Ltd.
Metrohm Martindale Electric Metrohm House, Imperial Park, Imperial Way, Watford, Hertfordshire, WD24 4PP, UK T: 01923 441717 F: 01923 446900 Email: sales@martindale-electric.co.uk web: www.martindale-electric.co.uk
More informationOPERATING INSTRUCTION
11/05 Form #273 OPERATING INSTRUCTION MODEL 4105 Disital Earth Resistance Tester 2150 joshua's Path, Suite 302, Hauppauge, NY 11788 Phone : 1-800-645-5398 or 1-639-231-7050 Fax : 1-639-434-3128 E-mail
More informationDigital/Analog Megohmmeter Model 1026 USER MANUAL
Digital/Analog Megohmmeter Model 1026 USER MANUAL Limited Warranty The Megohmmeter Model 1026, is warranted to the owner for a period of 2 years from the date of original purchase against defects in manufacture.
More informationMAX. AC 600V HOLD V M H.V. LIVE CIRCUIT DIGITAL INSULATION TESTER DO NOT OPERATE IF LIT POWER DATA HOLD TEST ON / OFF 250V 500V 1000V OFF CAT.
INSULATION TESTER EARTH MAX. AC 600V LINE AC -+ HOLD V k M LIVE CIRCUIT DIGITAL INSULATION TESTER DO NOT OPERATE IF LIT M H.V. POWER DATA HOLD TEST ON / OFF 250V 500V 1000V ACV OFF 0 CAT.III 600V INSTRUCTION
More informationInstruction Manual. 99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Model 308A Digital Insulation & Continuity Meter
Instruction Manual 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Model 308A Digital Insulation & Continuity Meter INDEX PAGE INSTRUMENT LAYOUT... 1 INTRODUCTION... 2 SAFETY
More informationUSER MANUAL. 200A AC Mini Clamp Meter. Model MA130. Please visit for user manual translations
USER MANUAL 200A AC Mini Clamp Meter Model MA130 Please visit www.extech.com for user manual translations Introduction Thank you for selecting the Extech Instruments 200A AC Mini Clamp Meter. The MA130
More informationUsers Manual. Accessories Motor and Phase Rotation Indicator ships with the following items: 3 test leads 3 test probes 3 alligator clips 9 V battery
MS5900 Users Manual Table of Contents Introduction Motor and Phase Rotation Indicator is a handheld, battery-operated instrument designed to detect the rotary field of three-phase systems and determine
More informationOPERATING INSTRUCTION
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 8/05 Form #270 OPERATING INSTRUCTION MODEL 3005 DIGITAL INSULATION-CONTINUITY TESTER
More information1.Safe testing IMPORTANT:
Electricity is dangerous and can cause injury and death. Always treat it with the greatest of respect and care. If you are not quite sure how to proceed, then stop, take advice from a qualified person.
More informationDigital/Analog Megohmmeter Model 1026
Digital/Analog Megohmmeter Model 1026 USER MANUAL 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Table of Contents Warning...3
More informationRental Industry Safety Tester Safe Check 5s
Rental Industry Safety Tester Safe Check 5s Feb 2006 2006 Clare Instruments Inc. Issue 2.0 Firmware Version : 1.2a Limited Warranty & Limitation of Liability Clare Instruments Inc, guarantees this product
More informationKMP Insulation-Continuity Tester. Users Manual
KMP 7036 Insulation-Continuity Tester Users Manual KMP7036 Insulation-Continuity Tester Users Manual English September 2011, Rev.1 2011 Amprobe Test Tools. All rights reserved. Printed in China Limited
More informationl The Battery Tester is designed for measuring the l AC four-terminal method to measure the internal
Certificate of Calibration We hereby certify that this product has been calibrated and found to be in accordance with the applicable SPECIFICATIONS and STANDARDS. Accuracies of the standard equipment used
More informationAC/DC CURRENT TRANSDUCER INSTRUCTION MANUAL
AC/DC CURRENT TRANSDUCER INSTRUCTION MANUAL INTRODUCTION 1-1 Unpacking and Inspection Upon removing your new Clamp Meter from its packing, you should have the following items: 1. Current Transducer with
More informationMARTINDALE MARTINDALE IN2001/IN2003 INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL IN2001/IN2003 INSULATION & CONTINUITY TESTERS
MARTINDALE ELECTRIC Martindale Electric Company LTD Metrohm House Penfold Trading Estate Imperial Way Watford Herts WD24 4YY T: 01923 441717 F: 01923 446900 Email: sales@martindale-electric.co.uk web:
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS Digital Clamp Meter DSA500A IMPORTANT: RECEIVING INSTRUCTIONS Visually inspect all components for shipping damage. If you find damage, notify the carrier at once. Shipping damage
More informationDIGITAL RCD(ELCB) TESTER
INSTRUCTION MANUAL DIGITAL RCD(ELCB) TESTER KEW 5410 R KYORITSU ELECTRICAL INSTRUMENTS WORKS, LTD. Contents 1. Safety Warnings.... 1 2. Procedure of removing Cover. 3 2-1 Method of removing the Cover.
More informationIN1001/IN1003 ANALOGUE INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL IN1001/IN1003 ANALOGUE INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL
Martindale Electric Company LTD Metrohm House Penfold Trading Estate Imperial Way Watford Herts WD24 4YY T: 01923 441717 F: 01923 446900 Email: sales@martindale-electric.co.uk web: www.martindale-electric.co.uk
More informationPY-11 Voltage & Continuity Tester
PY-11 Voltage & Continuity Tester Users Manual PY-11 Voltage & Continuity Tester English Users Manual May 2010, Rev.1 2010 Amprobe Test Tools. All rights reserved. Printed in China Limited Warranty and
More informationTable of Contents. Title Page UT501/UT502 OPERATING MANUAL. Introduction. Unpacking the Meter. Safety Information. International Electrical Symbols
Table of Contents Title Page Introduction Unpacking the Meter Safety Information International Electrical Symbols The Meter Structure Key Functions Rotary Switch Measurement Operation A. Measuring Voltages
More information362 Clamp Meter. Users Manual
362 Clamp Meter Users Manual PN 3622678 August 2010, Rev. 1, 4/13 2010, 2013 Fluke Corporation. All rights reserved. Printed in China. Specifications are subject to change without notice. All product names
More informationUser's Manual. Earth Ground Resistance Tester. Model Introduction
User's Manual Earth Ground Resistance Tester Model 382152 Introduction Congratulations on your purchase of the Extech Earth Ground Resistance Tester. This device can measure resistance (in 3 ranges) and
More informationNon-Contact Phase Rotation Tester
USER GUIDE Non-Contact Phase Rotation Tester Model PRT00 Model PRT00-M Introduction Congratulations on your purchase of this Extech Meter. The PRT00 is used to quickly and accurately determine three phase
More information4-WIRE EARTH RESISTANCE TESTER C1 ES P1 S. Max. AC 200V MICROPROCESSOR CONTROLLED TEST. Switch ON, TEST, SCROLL RESULTS 20Ω 200Ω 2000Ω OFF
2734 ER 4-WIRE EARTH RESISTANCE TESTER E C1 ES P1 S P2 H C2 Max. AC 200V Rc Rp MICROPROCESSOR CONTROLLED Noise CATⅣ 200V PRESS TO: Switch ON, TEST, SCROLL RESULTS TEST 20Ω 200Ω 2000Ω OFF EARTH VOLTAGE
More informationEZYPAT / EZYPAT+ / SMARTPAT PORTABLE APPLIANCE TESTER INSTRUCTION MANUAL
EZYPAT / EZYPAT+ / SMARTPAT PORTABLE APPLIANCE TESTER INSTRUCTION MANUAL CONTENTS 1. Safe testing... 2 2. Product summary and explanation... 5 2.1 Product summary... 5 2.2 Test Function... 5 2.3 Features...
More informationUSER GUIDE. Model RH10 Hygro Thermometer. Humidity and Temperature Meter
USER GUIDE Model RH10 Hygro Thermometer Humidity and Temperature Meter Introduction Congratulations on your purchase of the Extech Hygro Thermometer Model RH10. This device measures relative humidity and
More informationRS-3 PRO RS-1007 PRO. CAT IV Analog Clamp meter Series. Users Manual. For detailed specifications and ordering info go to
RS-3 PRO RS-1007 PRO CAT IV Analog Clamp meter Series Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com RS-3 PRO RS-1007 PRO CAT IV Analog Clampmeter Series English
More informationINSTRUCTION MANUAL PORTABLE APPLIANCE TESTER
INSTRUCTION MANUAL PORTABLE APPLIANCE TESTER KEW6201A CONTENTS 1. Safe testing 1 2. Procedure of removing cover. 3 2.1 Method of removing the cover. 3 2.2 Method of storing the cover. 3 3. Product summary
More informationSafetyPAT Plus A B P/N:
SafetyPAT Plus A B C P/N:110401103864 Test Instrument Solutions SafetyPat Plus Instructions A.Features SafetyPat Plus The SafetyPat Plus is a handheld battery powered unit suitable for carrying out electrical
More informationInstruction Manual & Specification
SP200, SP400 & VP400 Proving Units Instruction Manual & Specification VP400 SP200 SP400 SS0019V2 Sn 1. Safety 1.1 Equipment Markings Caution - refer to the instruction manual Construction is double insulated
More informationTIC 300 PRO. Users Manual Mode d emploi Bedienungshandbuch Manual d uso Manual de uso. Non Contact AC Voltage Detector. High Energy Tic Tracer
TIC 300 PRO High Energy Tic Tracer Non Contact AC Voltage Detector Users Manual Mode d emploi Bedienungshandbuch Manual d uso Manual de uso TIC 300 PRO High Energy Tic Tracer Non Contact AC Voltage Detector
More informationOPERATING MANUAL CMP-200
OPERATING MANUAL MINI AC LEAKAGE CURRENT METER CMP-200 Version 1.7 The CMP-200 digital clamp meter has been designed for the purpose of clamp measurements of alternative leakage current. Main features
More informationUsers Manual. Phase Rotation Indicator
9040 Phase Rotation Indicator Users Manual PN 2438546 April 2005, Rev.2, 5/11 2005-2011 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are
More informationNon-Contact Phase Rotation Tester
User's Guide 99 Washington Street Melrose, MA 076 Phone 78-665-400 Toll Free -800-57-84 Visit us at www.testequipmentdepot.com Non-Contact Phase Rotation Tester Model PRT00 Introduction Congratulations
More informationItem ref: UK & UK MTB01 & MTB02 DIGITAL MULTITESTERS. User Manual
Item ref: 600.101UK & 600.102UK MTB01 & MTB02 DIGITAL MULTITESTERS User Manual Please read this manual thoroughly and ensure all contents are fully understood before using the apparatus. Warning To avoid
More informationPOWERED BY KT71 / Portable Appliance Tester. Instruction Manual
KT71 / Portable Appliance Tester POWERED BY Instruction Manual CONTENTS 1. Safe testing 1 2. Procedure of removing cover.. 3 2.1 Method of removing the cover... 3 2.2 Method of storing the cover... 3 3.
More informationR&S RT-ZC02 R&S RT-ZC03 AC/DC Current Probe User Manual
R&S RT-ZC02 R&S RT-ZC03 AC/DC Current Probe User Manual / User Manual Content 1 Introduction 3 2 Safety 3 3 Specifications RT-ZC03 6 Specifications RT-ZC02 7 4 Operating Instructions RT-ZC03 8 Operating
More informationUser Guide. Model Insulation Tester / Megohmmeter
User Guide Model 380260 Insulation Tester / Megohmmeter Introduction Congratulations on your purchase of Extech s Insulation Tester/Megohmmeter. The Model 380260 provides three test ranges plus continuity
More informationMini Multimeter with Non-Contact Voltage Detector (NCV)
Owner s Manual Mini Multimeter with Non-Contact Voltage Detector (NCV) Model No. 82314 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product.
More informationKMP7010. Ground Resistance Tester. Users Manual
KMP7010 Ground Resistance Tester Users Manual KMP7010 Ground Resistance Tester Users Manual English June 2011, Rev.1 2011 Amprobe Test Tools. All rights reserved. Printed in China Limited Warranty and
More information1 This instrument must only be used by a competent and trained person and operated in strict accordance with the instructions.
1 This instrument must only be used by a competent and trained person and operated in strict accordance with the instructions. KYORITSU will not accept liability for any damage or injury caused by misuse
More informationASTROAI USER MANUAL DIGITAL MULTIMETER. NOTE: Fully read and understand this manual before using this instrument.
ASTROAI USER MANUAL DIGITAL MULTIMETER NOTE: Fully read and understand this manual before using this instrument. WARNING: To avoid possible electric shock or personal injury, and to avoid possible damage
More informationBK BK J93 MA BK MA BK MN93-BK MN193-BK MR193-BK SL261-BK SR193-BK
n 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com COMPATIBLE CURRENT PROBES & SENSORS FOR POWER QUALITY METERS 193-24-BK 193-36-BK
More information51 & 52 Series II. Users Manual. Thermometer. Test Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.
51 & 52 Series II Thermometer Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com Users Manual English September 1999 Rev.2, 11/10 1999-2010 Fluke Corporation,
More informationUser Guide. Model Insulation Tester / Megohmmeter
User Guide Model 380260 Insulation Tester / Megohmmeter Introduction Congratulations on your purchase of Extech s Insulation Tester/Megohmmeter. The Model 380260 provides three test ranges plus continuity
More informationDigital Multimeter User's Manual
Digital Multimeter User's Manual MS8239A MS8239A DIGITAL MULTIMETER Auto Power Off V HOLD 600 600 20 10A A m 10A 20m 2 m V MAX 10A/ 500V COM 600V CAT III IEC61010-1 12V 9V BATT. k 2M 600V MAX MAX ma/250v
More informationMM300. INSTRUCTION MANUAL Manual-Ranging Digital Multimeter
INSTRUCTION MANUAL Manual-Ranging Digital Multimeter MM300 DATA HOLD AUDIBLE CONTINUITY BATTERY TEST DIODE TEST 10A 2MΩ ESPAÑOL pg. 13 FRANÇAIS pg. 25 MM300-1390109ART.indd 1 9/21/2015 2:48:00 PM GENERAL
More informationDistributor. Kewtech Corporation Limited 76 St. Catherine s Grove Lincoln LN5 8NA KEWTECH
Distributor Kewtech Corporation Limited 76 St. Catherine s Grove Lincoln LN5 8NA www.kewtechcorp.com KEWTECH 92-1618 04-03 KEWTECH KT61 digital multi function tester Instruction manual Contents 1 Safe
More informationUser s Manual Power Supply. IM E 3rd Edition. Yokogawa Electric Corporation
User s Manual 700938 Power Supply Yokogawa Electric Corporation 3rd Edition Introduction Revisions Thank you for purchasing the 700938 Power Supply. This Instruction Manual contains useful information
More informationUSE AND CARE GUIDE DUALCHECK CIRCUIT TESTER
Item # 1002 153 664 Model #CE-VD7504GFI USE AND CARE GUIDE DUALCHECK CIRCUIT TESTER Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. 7
More information365 Detachable Jaw True-rms Clamp Meter
365 Detachable Jaw True-rms Clamp Meter Users Manual PN 3622684 August 2010 2010 Fluke Corporation. All rights reserved. Printed in China. Specifications are subject to change without notice. All product
More informationAMB V Insulation Resistance Tester. Users Manual. For detailed specifications and ordering info go to
AMB-50 5000V Insulation Resistance Tester Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com AMB-50 5000V Insulation Resistance Tester Users Manual English June
More information323/324/325 Clamp Meter
323/324/325 Clamp Meter Users Manual PN 4045153 May 2012 2012 Fluke Corporation. All rights reserved. Printed in China. Specifications are subject to change without notice. All product names are trademarks
More informationINSP-3 Wiring Inspection Tester
INSP-3 Wiring Inspection Tester Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com INSP-3 Wiring Inspection Tester Users Manual English December 2009, Rev.1 2009
More informationi3000s/i2000 Flex AC Current Probe
i3000s/ AC Current Probe Instruction Sheet Introduction The i3000s 24 Flex, i3000s 36 Flex, and AC Current Probes (the Probe) are used with oscilloscopes, digital multimeters, recorders or data loggers.
More informationKEWTECH. KT56 digital multi function tester. Instruction manual
KEWTECH KT56 digital multi function tester Instruction manual Contents 1 Safety Notice 1 2 Features and Principles of Measurement 3 3 Introduction 6 4 Specifications 7 5 Instrument layout 9 6 Operating
More informationTX900. Microwave Leakage Detector. 99 Washington Street Melrose, MA Phone Toll Free
TX900 Microwave Leakage Detector 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Users Manual TX900 Microwave Leakage Detector
More informationOPERATING INSTRUCTION
11/05 Form #271 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 OPERATING INSTRUCTION Visit us at www.testequipmentdepot.com MODEL 3132 ANALOG INSULATION-CONTINUITY TESTER
More information5.2 PRE-OPERATION PROCEDURE WARRANTY
4/02 Form #314 OPERATING INSTRUCTIONS MODELS DM-210A, 220A, 230A DIGITAL MULTIMETER PLEASE READ THESE OPERATING INSTRUCTIONS CAREFULLY Misuse and or abuse of these instruments cannot be prevented by any
More informationLH41A. User Manual. Clamp On Ammeter. For detailed specifications and ordering info go to
LH41A Clamp On Ammeter User Manual For detailed specifications and ordering info go to www.testequipmentdepot.com LH41A Clamp On Ammeter Users Manual English April 2007, Rev.2 2007 Amprobe Test Tools.
More informationThe following table shows the symbols used on the product and/or in this manual. Hazardous Voltage. Risk of electric shock.
i6000s Flex AC Current Probe Instruction Sheet Introduction The i6000s 24 Flex and i6000s 36 Flex AC Current Probes (hereafter referred to as the Probes ) are used with oscilloscopes, digital multimeters,
More informationDT304. Digital Temperature Logger INSTRUCTION MANUAL
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com DT304 INSTRUCTION MANUAL Digital Temperature Logger TABLE OF CONTENTS Introduction..........................................1
More informationUser Guide. Model Insulation Tester / Megohmmeter. Introduction
User Guide Model 380363 Insulation Tester / Megohmmeter Introduction Congratulations on your purchase of Extech s Insulation Tester/Megohmmeter. The Model 380363 provides three test ranges plus continuity
More information1 INTRODUCTION SPECIFICATIONS Electrical Data General Data... 3
International Electrical Symbols Caution! Refer to this manual before using the probe Probe is protected by Reinforced or Double Insulation CONTENTS Page 1 INTRODUCTION... 2 2 SPECIFICATIONS... 2 2.1 Electrical
More informationModel Insulation Tester / Megohmmeter. User Manual
Model 380363 Insulation Tester / Megohmmeter User Manual Introduction Congratulations on your purchase of Extech s Insulation Tester/Megohmmeter. The Model 380363 provides three test ranges plus continuity
More informationBK BK A BK MA BK MA BK J93 MN93-BK MN193-BK MR193-BK SL261-BK SR193-BK
n COMPATIBLE CURRENT PROBES & SENSORS FOR POWER QUALITY METERS 193-24-BK 193-36-BK A196-24-BK MA193-10-BK MA193-14-BK J93 MN93-BK MN193-BK MR193-BK SL261-BK SR193-BK E N G L I S H User Manual Copyright
More informationOPERATING INSTRUCTIONS. TempCheck Non-Contact Infrared Thermometer IRT200 F C + -
OPERATING INSTRUCTIONS TempCheck Non-Contact Infrared Thermometer IRT200 1 8 2 4 5 7 6 3 F C 00.0 SCAN + - Figure 1 MAX HOLD E= Figure 3 0.00 Figure 2 NUMBER DESCRIPTION NUMBER DESCRIPTION 1 Laser 5 C
More informationBATTERY OPERATED DIGITAL MILLI-OHMMETER
BATTERY OPERATED DIGITAL MILLI-OHMMETER C 1 P 1 P 2 C 2 MAX. DC20V MICROPROCESSOR CONTROLLED AC DC HOLD M A X M I N AUTO-HOLD Hz mv km ka ms DIGITAL MILLIOHM METER 2000 200.0 20.00 2000m Test Current Range
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 51 & 52 Series II Thermometer Users Manual English September 1999 Rev.1,
More informationAC/DC CURRENT TRANSDUCER 600A 10mV/1A, 1mV/1A
AC/DC CURRENT TRANSDUCER 600A 10mV/1A, 1mV/1A INTRODUCTION 1-1 Unpacking and Inspection Upon removing your new Current Transducer from its packing, you should have the following items: 1. Current Transducer
More informationCONTACTS RELAY TESTER 66249
RELAY TESTER 66249 These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder
More informationMY /2-DIGIT DIGITAL MULTIMETER Users Manual
MY-65 4 1/2-DIGIT DIGITAL MULTIMETER Users Manual Read the Users Manual thoroughly before use. WARRANTY This instrument is warranted to be free from defects in material and workmanship for a period of
More informationVisit us at
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Introduction 717 30G & 717 100G Pressure Calibrators Instruction Sheet The Fluke
More informationDeclaration of Conformity
We Declaration of Conformity GOOD WILL INSTRUMENT CO., LTD. No. 7-1, Jhongsing Rd, Tucheng City, Taipei County 236, Taiwan GOOD WILL INSTRUMENT (SUZHOU) CO., LTD. No.69 Lushan Road, Suzhou New District
More informationPro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
More information7/05 FORM#347 OPERATING INSTRUCTIONS MULTI FUNCTION TESTER MODEL 6030
7/05 FORM#347 OPERATING INSTRUCTIONS MULTI FUNCTION TESTER MODEL 6030 Contents 1. Safety Precautions 1 2. Features 3 3. Specifications 4 4. Layout Diagram 7 5. Preparation for Measurement 9 6. Operation
More informationKD1E Range Potential Indicators
KD1E Range Potential Indicators Operating Instructions 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Limited Warranty & Limitation
More informationINSTRUCTION MANUAL ANALOGUE INSULATION TESTER KEW 3131M KYORITSU ELECTRICAL INSTRUMENTS WORKS,LTD., TOKYO JAPAN
INSTRUCTION MANUAL ANALOGUE INSULATION TESTER KEW 3131M KYORITSU ELECTRICAL INSTRUMENTS WORKS,LTD., TOKYO JAPAN Contents 1. Safety Precautions... 1 2. Features... 3 3. Specifications... 4 4. Instrument
More informationCalibrator Capabilities Function Range Resolution Measure V dc 28 V 1 mv Measure ma dc Source ma dc
707 Loop Calibrator Instruction Sheet Introduction The Fluke 707 Loop Calibrator (hereafter, the Calibrator) is a compact sourcing and measuring tool. The Calibrator tests current loops of 0-20 ma or 4-20
More information373 Clamp Meter. Users Manual
373 Clamp Meter Users Manual PN 3612805 July 2010 2010 Fluke Corporation. All rights reserved. Printed in Taiwan. Specifications are subject to change without notice. All product names are trademarks of
More informationAttention ETCR8600 Leakage Protector Tester To read this user manual carefully. To comply with the operating cautions presented in this manual.
Content Attention... 2 I. Brief introduction... 4 II. Electrical Symbol... 4 III. Technical Specification... 4 IV. Instrument Structure... 6 V. Instrument Operation... 6 1. boot up, shutdown... 6 2. Manual
More informationORIGINAL INSTRUCTIONS
OPERATION & MAINTENANCE INSTRUCTIONS CBB200 Shown here BUFFER/POLISHER MODEL NO: CBB150, CBB200 PART NO: 6500485, 6500490 ORIGINAL INSTRUCTIONS LS0818 - ISS 1 INTRODUCTION Thank you for purchasing this
More information4-20mA DC PROCESS CLAMP METER
An ISO 9001:2008 Company The KM 071 Milliamp Process Clamp Meter is a Hand-held battery operated clamp meter that measures 4-20 ma DC without breaking the electrical circuit. Unlike conventional clamp
More informationUser s Manual Power Supply IM E. 5th Edition
User s Manual 700938 Power Supply 5th Edition Thank you for purchasing the 700938 Power Supply. This user s manual contains useful information about the instrument s functions and operating procedures
More information3 PHASE TESTER & MOTOR ROTATION TESTER
3 PHASE TESTER & MOTOR ROTATION TESTER R S T TEST CAT. III 500V 3 PHASE TESTER & MOTOR ROTATION TESTER CCW CW BAT. L2 L1 L3 L1 L2 L3 MOTOR ROTATION INSTRUCTION MANUAL INDEX Page 1. INTRODUCTION... 1 2.
More informationAC50A. Leakage Clamp Meter. User Manual. For detailed specifications and ordering info go to
AC50A Leakage Clamp Meter User Manual For detailed specifications and ordering info go to www.testequipmentdepot.com Contents AC50A Current Clamp Meter Introduction... 2 Contents... 3 Transport and Storage...
More informationHOME CHARGER MODE 2. Series to /32A single phase CONTENTS. Manual IMPORTANT SAFETY INSTRUCTIONS 3 SAFETY INFORMATION 4 INSTALLATION 5
CONTENTS IMPORTANT SAFETY INSTRUCTIONS 3 SAFETY INFORMATION 4 INSTALLATION 5 OPERATION 8 SPECIFICATIONS 8 MAINTENANCE 9 HOME CHARGER MODE 2 Series 31328 to 31340 16/32A single phase FCC INFORMATION 9 WARRANTY
More information5 IN 1 JUMP START OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: JS5IN1 PART NO: LS0810
5 IN 1 JUMP START MODEL NO: JS5IN1 PART NO: 6240005 OPERATION & MAINTENANCE INSTRUCTIONS LS0810 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please
More information