2009 Buick Truck Enclave AWD V6-3.6L
|
|
|
- Oliver McGee
- 5 years ago
- Views:
Transcription
1 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 1 of Buick Truck Enclave AWD V6-3.6L Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank Unit» Service and Repair Fuel Tank Module Replacement Special Tools J Fuel Sender Lock Ring Wrench Removal Procedure Warning Whenever fuel line fittings are loosened or removed, wrap a shop cloth around the fitting and have an approved container available to collect any fuel. Caution: Clean all fuel pipe and hose connections and surrounding areas before disassembling to avoid possible contamination of the fuel system. Spray the fuel pump module cam-lock ring tang with penetrating oil prior to attempting removal. Note: A NEW fuel tank module seal is necessary each time the fuel tank module is serviced. Obtain a NEW seal prior to beginning this service procedure.
2 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 2 of Remove the fuel tank. Refer to Fuel Tank Replacement (See: Fuel Tank\Service and Repair). 2. Disconnect the fuel pump fuel feed line quick connect fitting (1) from the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 3. Disconnect evaporative emission (EVAP) canister vent front pipe quick connect fitting (4) from the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 4. Reposition the fuel pump fuel feed line and the EVAP canister vent front pipe out of the way. 5. Disconnect the fuel sender wiring harness electrical connector (2) from the fuel tank pressure sensor. 6. Disconnect the fuel sender wiring harness electrical connector (3) from the fuel tank module.
3 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 3 of 10 Caution: Avoid damaging the lock ring. Use only J to prevent damage to the lock ring. 7. Install the J (1) to the fuel tank module lock ring.
4 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 4 of 10 Note: Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation. 8. Using the J and a long breaker-bar, rotate the lock ring counterclockwise unlocking the fuel tank module lock ring. 9. Remove the J
5 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 5 of 10 Caution: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints. 10. Remove the fuel tank module lock ring (1). 11. Slowly raise the module (2) until the fuel level sensor float arm is just visible. Note: When removing the module from the fuel tank, be aware that the module reservoir bucket is full of fuel. The module must be tipped slightly during removal to avoid bending the fuel level sensor float arm. 12. Tilt the module towards the lower front corner of the fuel tank to allow the level sensor float arm to clear the tank opening. Remove the module from the fuel tank. 13. Carefully discard the fuel in the module reservoir bucket into an approved container. 14. Remove and discard the fuel tank module seal (3). 15. Remove the fuel level sensor, if required. Refer to Fuel Level Sensor Replacement (See: Computers and Control Systems\Fuel Level Sensor\Service and Repair).
6 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 6 of 10 Note: Some lock ring were manufactured with DO NOT REUSE stamped into them. These lock rings may be reused if they are not damaged or warped. Inspect the lock ring for damage due to improper removal or installation procedures. If damage is found, install a NEW lock ring. Check the lock ring for flatness. 16. Place the lock ring on a flat surface. Measure the clearance between to lock ring and the flat surface using a feeler gage at 7 points. 17. If the warpage is less than 0.41 mm (0.016 in), the lock ring does not require replacement. 18. If the warpage is greater than 0.41 mm (0.016 in), the lock ring must be replaced. Installation Procedure
7 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 7 of Install the fuel level sensor, if required. Refer to Fuel Level Sensor Replacement (See: Computers and Control Systems\Fuel Level Sensor\Service and Repair). 2. Install a NEW fuel tank module seal (3) onto the fuel tank. Note: The bucket must be tipped slightly during installation to avoid bending the fuel level sensor bloat arm. 3. Tilt the module towards the lower front corner of the fuel tank to allow the level sensor float arm to clear the tank opening. Install the module into the fuel tank. 4. Position and install the fuel tank module lock ring (1).
8 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 8 of Install the J to the fuel tank module lock ring. 6. Using the J and a long breaker-bar, rotate the lock ring clockwise locking the fuel tank module lock ring.
9 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 9 of Remove the J (1) from the fuel tank module lock ring.
10 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 10 of Connect the fuel sender wiring harness electrical connector (3) to the fuel tank module. 9. Connect the fuel sender wiring harness electrical connector (2) to the fuel tank pressure sensor. 10. Position the fuel pump fuel feed line and the EVAP canister vent front pipe to the fuel tank. 11. Connect EVAP canister vent front pipe quick connect fitting (4) to the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 12. Connect the fuel pump fuel feed line quick connect fitting (1) to the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 13. Install the fuel tank. Refer to Fuel Tank Replacement (See: Fuel Tank\Service and Repair).
11 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 1 of Buick Truck Enclave AWD V6-3.6L Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank» Service and Repair» Fuel Tank Replacement Fuel Tank Replacement Removal Procedure Warning Do not allow smoking or the use of open flames in the area where work on the fuel or EVAP system is taking place. Anytime work is being done on the fuel system, disconnect the negative battery cable, except for those tests where battery voltage is required. Warning Fuel supply lines will remain pressurized for long periods of time after the engine is shutdown. This pressure must be relieved before servicing the fuel system.
12 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 2 of Relieve the fuel system pressure. Refer to Fuel Pressure Relief (With CH-48027) (See: Fuel Pressure Release\Service and Repair\Fuel Pressure Relief (With CH-48027))Fuel Pressure Relief (Without CH ) (See: Fuel Pressure Release\Service and Repair\Fuel Pressure Relief (Without CH-48027)). 2. Drain the fuel tank. Refer to Fuel Tank Draining (See: Service and Repair). Warning Whenever fuel lines are removed, catch fuel in an approved container. Container opening must be a minimum of 300 mm (12 in) diameter to adequately catch the fluid. Caution: Clean all fuel pipe connections and surrounding areas before disconnecting the fuel pipes to avoid contamination of the fuel system. 3. Disconnect the fuel pump fuel feed line quick connect fitting (6) from the chassis fuel line. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 4. Disconnect the fuel tank evaporative emission (EVAP) canister vent front pipe quick connect fitting (5) from the chassis EVAP line. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 5. Disconnect the vent hose from the left rear of the fuel tank.
13 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 3 of Disconnect the fuel sender wiring harness electrical connector (2) from the body wiring harness electrical connector. 7. Remove the fuel sender wiring harness clip (1) from the underbody side rail extension. 8. Remove the left underbody side rail. Refer to Underbody Rear Side Rail Replacement (). 9. Support the fuel tank with a suitable adjustable jack. 10. Remove the fuel tank strap bolts (1). Allow the fuel tank straps to hang.
14 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 4 of 26 Caution: Do not bend the fuel tank straps. Bending the fuel tank straps may cause damage to the straps. 11. Push up on the rear of the strap slightly and rotate the strap towards the rear of the vehicle, in order the remove the fuel tank straps (1).
15 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 5 of Using the adjustable jack and the aid of an assistant, lower the fuel tank from the underbody of the vehicle. 13. With the aid of the assistant, remove the fuel tank from the adjustable jack, and place on a flat work surface.
16 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 6 of If replacing the fuel tank, perform the following steps, otherwise proceed to step 21 in the installation procedure. 15. Remove the fuel tank front and rear shield push on nuts (2). 16. Remove the fuel tank front and rear shield nuts (3). 17. Remove the fuel tank front (1) and rear (4) shields.
17 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 7 of Remove the foam pad insulators (1) from the top of the fuel tank.
18 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 8 of Disconnect the fuel pump fuel feed line quick connect fitting (1) from the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 20. Remove the fuel pump fuel feed line from the retaining features (2) built into the fuel tank and out from under the EVAP canister vent rear pipe.
19 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replacement Page 9 of Disconnect the EVAP canister vent front pipe quick connect fitting (1) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 22. Remove the EVAP canister vent front pipe from the retaining features (2) built into the fuel tank.
20 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 10 of Disconnect the fuel sender wiring harness electrical connectors from the fuel tank module (1), fuel tank pressure sensor 2), and EVAP canister vent solenoid (3). 24. Remove the fuel sender wiring harness.
21 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 11 of Disconnect the EVAP canister vent rear pipe quick connect fitting (1) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 26. Squeeze the retainer (2) into order to disengage the retainer from the EVAP canister, and remove the EVAP canister assembly from the EVAP canister bracket retainers (1).
22 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 12 of Disconnect the EVAP canister vent rear pipe quick connect fittings (1) from the fuel tank rollover valves. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 28. Disconnect the EVAP canister vent rear pipe quick connect fitting (2) from the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 29. Remove the EVAP canister vent rear pipe from the retaining features (3) built into the fuel tank. 30. Remove the fuel tank module. Refer to Fuel Tank Module Replacement (See: Fuel Tank Unit\Service and Repair). Installation Procedure
23 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 13 of If the fuel tank was replaced, perform the following steps, otherwise proceed the step Install the fuel tank module. Refer to Fuel Tank Module Replacement (See: Fuel Tank Unit\Service and Repair). 3. Lay the EVAP canister vent rear pipe into position on the fuel tank. 4. Connect the EVAP canister vent rear pipe quick connect fittings (1) to the fuel tank rollover valves. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 5. Connect the EVAP canister vent rear pipe quick connect fitting (2) to the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 6. Install the EVAP canister vent rear pipe to the retaining features (3) built into the fuel tank.
24 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 14 of Insert the rear of the EVAP canister into the EVAP canister bracket retainers (1), squeeze the retainer (2), and set the EVAP canister assembly into place. 8. Connect the EVAP canister vent rear pipe quick connect fitting (1) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service).
25 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 15 of Place the fuel sender wiring harness into the channel in the fuel tank. 10. Connect the fuel sender wiring harness electrical connectors to the fuel tank module (1), fuel tank pressure sensor (2), and EVAP canister vent solenoid (3).
26 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 16 of Lay the EVAP canister vent front pipe into position on the fuel tank. 12. Connect the EVAP canister vent rear pipe quick connect fitting (1) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 13. Install the EVAP canister vent rear pipe to the retaining features (2) built into the fuel tank.
27 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 17 of Route the fuel pump fuel feed pipe under the EVAP canister vent rear pipe and lay into position on the fuel tank. 15. Connect the fuel pump fuel feed line quick connect fitting (1) to the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 16. Install the fuel pump fuel feed line to the retaining features (2) built into the fuel tank.
28 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 18 of Install the foam pad insulators (1) onto the top of the fuel tank.
29 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 19 of Install the fuel tank rear (4) and front (1) shields onto the fuel tank. 19. Install the fuel tank front and rear shield push on nuts (2). 20. Install the fuel tank front and rear shield nuts (3) until snug.
30 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 20 of With the aid of an assistant, remove the fuel tank from the work surface and place on the adjustable jack. 22. With the aid of the assistant, raise the fuel tank into position under the vehicle.
31 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 21 of Install the fuel tank straps (1).
32 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 22 of 26 Caution: Refer to Fastener Caution (See: Service Precautions\Vehicle Damage Warnings\Fastener Caution). 24. Install the fuel tank strap bolts (1). Tighten the bolts to 47 Nm (35 lb ft). 25. Remove the adjustable jack from under the fuel tank. 26. Install the left underbody side rail. Refer to Underbody Rear Side Rail Replacement ().
33 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 23 of Connect the fuel sender wiring harness electrical connector (2) to the body wiring harness electrical connector. 28. Install the fuel sender wiring harness clip (1) to the underbody side rail extension. 29. Connect the vent hose to the left rear of the fuel tank.
34 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 24 of Connect the fuel tank EVAP canister vent front pipe quick connect fitting (5) to the chassis EVAP line. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 31. Connect the fuel pump fuel feed line quick connect fitting (6) to the chassis fuel line. Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service).
35 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 25 of 26 Note: Ensure that the notch in the fill hose aligns with the tab on the fuel tank. 32. Position and install the fuel tank fill pipe (2) to the fuel tank. 33. Connect the EVAP canister vent rear pipe quick connect fitting (4) to the recirculation line on the fuel fill pipe (3). Refer to Plastic Collar Quick Connect Fitting Service (See: Fuel Line Coupler\Service and Repair\Plastic Collar Quick Connect Fitting Service). 34. Tighten the fuel tank fill hose clamp (1) at the fuel tank. Tighten the clamp to 3.3 Nm (29 lb in). 35. Lower the vehicle. 36. Refill the fuel tank. 37. Tighten the fuel fill cap. 38. Use the following procedure in order the inspect for leaks: 1. Turn the ignition ON, with the engine OFF, for 2 seconds. 2. Turn the ignition OFF for 10 seconds. 3. Turn the ignition ON, with the engine OFF. 4. Inspect for fuel leaks.
36 ALLDATA Repair Buick Truck Enclave AWD V6-3.6L - Fuel Tank Replaceme... Page 26 of Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement (See: Fuel Injector\Service and Repair).
PRIMARY FUEL TANK MODULE REPL... FUEL TANK REPLACEMENT (FWD) (ENGINE CONTROLS 3.4L) Document ID#
PRIMARY FUEL TANK MODULE REPL... FUEL TANK REPLACEMENT (FWD) (ENGINE CONTROLS 3.4L) Document ID# 1389484 Fuel Tank Replacement (FWD) Removal Procedure Caution: Do not allow smoking or the use of open flames
FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID#
FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# 824435 Fuel Tank Replacement (Cab/Chassis Front) Removal Procedure http://dh.identifix.com/searchfixes/index?roid=158586813&vid=2018330&vsm=4&hasbookmark=0&locationid=2#kw=fuel+pump&soption=1&vetid=8&stmode=1&paging=&smode=2&position=assetcat_9
1. Remove the fuel sender assembly. Refer to Fuel Sender Assembly Replacement.
FUEL LEVEL SENSOR REPLACEMENT Removal Procedure Fig. 105: Identifying Fuel Tank Module 1. Remove the fuel sender assembly. Refer to Fuel Sender Assembly Replacement. Sunday, October 26, 2008 8:48:25 8:48:30
1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
Disconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
Zoom and Print Options
Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank» Service and Repair» Procedures» Fuel Tank Removal and Installation REMOVAL WARNING: DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR
REMOVAL AND INSTALLATION
310-00-1 Fuel System 310-00-1 REMOVAL AND INSTALLATION Fuel Tank and Filler Pipe Special Tool(s) Fuel Tank Drain Hose 310-F013 2. NOTE: Steps 2 through 5 are only necessary if servicing the fuel tank or
FUEL TANK DRAINING. Special Tool(s) Special Tool(s)
FUEL TANK DRAINING Special Tool(s) Zoom Special Tool(s) WARNING: Do not smoke, carry lighted tobacco or open flame of any type when working on or near any fuel-related component. Highly flammable mixtures
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
REMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
ALLDATA Online Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10. Service and Repair
ALLDATA Online - 2009 Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
Do not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
FUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE)
ALLDATA Repair - 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) - Service and R... Page 1 of 12 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Vehicle» Powertrain Management» Fuel Delivery and Air Induction»
2014 Ford Edge SE ENGINE Fuel Tank & Lines - Edge, MKX
17. Remove the 2 nuts, 7 bundle retainer clips and remove the fuel supply and EVAP vapor tube assembly. To install, tighten to 9 Nm (80 lb-in). 18. To install, reverse the removal procedure. FUEL LINES
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
FUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
Fuel System Diagnosis
Page 1 of 6 2001 Chevrolet Express Express, Savana (VIN G) Service Manual Engine Engine Controls - 5.0L and 5.7L Diagnostic Information and Procedures Document ID: 720867 Fuel System Diagnosis Circuit
FUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL SENSOR
2007 Volkswagen Touareg (7LA) V6-3.6L (BHK)
Page 1 of 11 2007 Volkswagen Touareg (7LA) V6-3.6L (BHK) Vehicle» Engine, Cooling and Exhaust» Engine» Intake Manifold» Service and Repair» Intake Manifold Intake Manifold Special tools, testers and auxiliary
Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
FUEL SYSTEM SECTION FL CONTENTS ENGINE FL-1 PRECAUTION... 2 PREPARATION... 4 PERIODIC MAINTENANCE... 5 DISASSEMBLY AND ASSEMBLY...
ENGINE SECTION FL FUEL SYSTEM FL C D CONTENTS E PRECUTION... 2 PRECUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "IR BG" and "SET BELT PRE-TEN- SIONER"...2 General Precaution...2 PREPRTION...
w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
Cylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
FUEL SYSTEM SECTION FL CONTENTS ENGINE FL-1 PRECAUTION... 2 ON-VEHICLE REPAIR... 6 PREPARATION... 3 SERVICE DATA AND SPECIFICATIONS (SDS)...
ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precautions Necessary
BEFORE BEGINNING INSTALLATION
COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
ENGINE REMOVAL & INSTALLATION
TORQUE VALUES ENGINE MOUNTING = Apply Victory All Purpose Grease 2872187 1. Install all bolts in order A-H Do not tighten. E 41 Nm (30 lb-ft) M8 x 25mm D 111 Nm (82 lb-ft) 12 x 100mm ENGINE INSTALLATION
1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY PFP:17042 Removal and Installation EBS00M47 1. Lock ring 2. Fuel level sensor, fuel filter, and fuel pump assembly FL-6 3. Fuel level sensor,
FUEL SYSTEM SECTION FL CONTENTS B ENGINE FL-1
B ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL
AIR CLEANER GENERAL REMOVAL. 1CAUTION Do not run engine without filter element in place. Debris could be drawn into the engine causing damage.
AIR CLEANER GENERAL The air cleaner prevents foreign material from entering the carburetor and engine by trapping airborne dust and dirt in the filter element. Service air cleaner filter element every
Ford 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
TOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation
TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake
Intake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
2004 Lincoln LS Workshop Manual
SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose
PRODUCT USE INFORMATION
9RC61000 Jeep YJ Body Lift Thank you for choosing Rough Country for all your suspension needs. This body lift fits both manual and Automatic equipped vehicles!!! Refer to last page of this Instruction
2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
Multistrada (MTS) Tank Installation Notes. Tools Required. Phase 1: Remove Fairings. Phase 2: Remove Fuel Tank
The California Cycleworks MTS tank provides an aftermarket alternative to the OEM nylon fuel tanks as used on aircooled Desmodue Ducati Multistrada 1100, 1000, and 620 models. This fuel tank is NOT for
2007 Dodge Nitro R/T ENGINE Fuel System - Nitro. TORQUE SPECIFICATION DESCRIPTION N.m Ft. Lbs. In. Lbs. Accelerator Pedal
2007 ENGINE Fuel System - Nitro SPECIFICATIONS TORQUE SPECIFICATION TORQUE SPECIFICATION DESCRIPTION N.m Ft. Lbs. In. Lbs. Accelerator Pedal 12-105 Bracket Mounting Nuts Crankshaft Position 28 21 - Sensor
1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
1999 Oldsmobile Truck Bravada V6-4.3L VIN W
1 of 6 8/24/2015 9:53 PM 1999 Oldsmobile Truck Bravada V6-4.3L VIN W Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Meter Body» Service and Repair CLEANING AND INSPECTION PROCEDURE
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
Service Bulletin 1988 PRELUDE. RECALL: 1988 Prelude Power Steering Supply Hose
Service Bulletin Model Applicable To File Under Bulletin No. 1988 PRELUDE See VEHICLES AFFECTED ENGINE 88-014 Issue Date APRIL 20, 1988 RECALL: 1988 Prelude Power Steering Supply Hose PROBLEM When subjected
SECTION 4 - FUEL SYSTEMS AND CARBURETION
SECTION - FUEL SYSTEMS AND CARBURETION FUEL SYSTEMS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -62 FUEL PUMP - - - - - - -
FUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
FUEL SYSTEM B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tools... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3
The following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
INTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
Installation Instructions for Chevrolet C5 Corvette Lingenfelter High Flow Fuel Pump Module
Installation Instructions for 1997-2003 Chevrolet C5 Corvette Lingenfelter High Flow Fuel Pump Module PN: L710650197 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552
Fuel Supply Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Supply Component Description FIGURE Central SFI Fuel System with Fuel Pressure Gauge(c) (1) Fuel Inlet (2) Bleed Hose (3) J 34730-1A Fuel Pressure Gage Assembly (4)
Removing and Installing Battery
ALLDATA Online - 2005 Porsche 911 GT3 (996) F6-3.6L - Removing and Installing Bat... Page 1 of 13 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's
(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector.
REMOVAL 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. 3. DISCHARGE FUEL SYSTEM PRESSURE
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
FUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
FUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
Fuel System Diagnosis
1996 Chevrolet Impala Caprice, Impala, Roadmaster (VIN B) Service Manual Engine Engine Controls - 4.3L (Caprice Only) and 5.7L Diagnostic Information and Procedures Document ID: 37723 Fuel System Diagnosis
255 Liter/Hr, In Tank Fuel Pump For Chrysler Front Wheel Drive Vehicles Catalog # INSTALLATION INSTRUCTIONS
255 Liter/Hr, In Tank Fuel Pump For 1984-1990 Chrysler Front Wheel Drive Vehicles Catalog # 17934 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before installing your new In-Tank
Sniper EFI Conversion Fuel Tanks
Sniper EFI Conversion Fuel Tanks Congratulations on your purchase of the Sniper EFI Conversion Fuel Tank. The following assembly instructions will assist you in installing the tank, fuel level sender,
TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
Fuel supply system components, removing and installing
20-1 Fuel supply system components, removing and installing Checking fuel system for leaks Removing and installing fuel filter and draining water, engine code AAZ: Repair Manual, 1.9 Liter 4-Cyl. 2V Eco-Diesel
2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 9 SECTION 303-04: Fuel Charging and Controls 2002 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/13/2001 Fuel Injection Supply Manifold Material
FUEL SYSTEM SECTION FL CONTENTS B ENGINE FL-1
FUEL SYSTEM B ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Battery Service... 2 PREPARATION... 3 Commercial Service Tools... 3 FUEL SYSTEM... 4 Checking Fuel Lines...
Assembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious
1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
M-9407-GT05 Mustang GT Dual Fuel Pump Kit INSTRUCTION SHEET
Please contact the Techline for the most current instruction information (800) FORD788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following information describes
This information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
REMOVAL AND REPLACEMENT
2005 Scion tc L4-2.4L (2AZ-FE) Vehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/39648/component/20/itype/401/nonstandard/
GXS14 - Civic Natural Gas Fuel Tank Solenoid Valve Replacement
Objective Remove In-Tank Solenoid Valve Inspect Fuel Tank for Liquid Contamination Evaluate Replacement Valve Condition Install In-Tank Solenoid Valve and Leak Check Align New Solenoid Valve and Connect
Powerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
Timing Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
ALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil)
ALLDATA Online - 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T - Steering... Page 1 of 12 Steering Wheel Module Coil Replacement (Coil) INFLATABLE RESTRAINT STEERING WHEEL MODULE COIL REPLACEMENT (COIL)
Last Revision: 30JN THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 30JN2007 1969 THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic
Plastic Collar Quick Connect Fitting Service
2004 Chevrolet Silverado 1500 -Fuel Systems > Fuel Controls -4.8L, 5.3L, And 6.0L > Repair Ins... Page 1 of 10 2004 Chevrolet Silverado 1500 : Fuel Systems > Fuel Controls - 4.8L, 5.3L, And 6.0L > Repair
TECHNICAL INFORMATION RECALL ACE System Pipe Leak
RECALL ACE System Pipe Leak AFFECTED VEHICLE RANGE: Ref: Issue: 1 Date: 01/12/01 Discovery Series II (LT) YA261114 to YA263118 SITUATION: ACE HIGH-PRESSURE PIPE MISBUILD Some ACE high pressure supply pipes
Installation Instructions Pro Bandit Shifter Fits: GM Powerglide Automatic Transmissions
Installation Instructions Pro Bandit Shifter Fits: 1962-1973 GM Powerglide Automatic Transmissions Part # 80793 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and
Phone Fax
Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator
CROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT
PAGE 1 OF 6 AFFECTED S: OVERVIEW CROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT CERTAIN 1992 THROUGH 2003 MODEL YEAR CROWN VICTORIA POLICE INTERCEPTOR (CVPI) S CURRENTLY IN POLICE
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
STEERING COLUMN - STANDARD
STEERING COLUMN - STANDARD 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Standard Celica DESCRIPTION & OPERATION Steering column is a collapsible 2-piece design. Columns use shear pins to
This chapter contains operational verification, adjustment, and repair/replacement procedures for major
V. MAJOR SYSTEMS REPAIR This chapter contains operational verification, adjustment, and repair/replacement procedures for major systems of the RICON. Each section also provides a brief functional description
This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
1 of 27 7/21/2015 3:33 PM
1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work
AEROMOTIVE Part # & Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18651 & 18652 Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
TECHNICAL INFORMATION
RECALL ACE System Pipe Leak AFFECTED VEHICLE RANGE: Ref: Issue: 2 Date: 02/29/00 Discovery Series II (LT) YA228484 to YA258264 SITUATION: NOTE: The vehicle VIN range includes vehicles that are not equipped
Authorized Field Change
Authorized Field Change AFC 08907R Date: June, 2008 Subject File: ENGINE Subject: Fuel Pressure Regulator and Fuel Pressure Switch on VT 275 Engines in Workhorse Commercial Chassis Model: Workhorse Start
Installation Instructions and Warranty Information
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 6695S 2007-14 5.4/5.8 Ford Mustang
Installation Instructions
SLP GM/Chevrolet LS3 COIL COVER KIT 2010+ Camaro 5.3L/6.2L 2007+ GMT900 5.3L/6.2L PN: 620038 Installation Instructions Important Notes: Before installing your SLP Coil Cover Kit, please read the installation
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)
Page 1 of 49 20-6 Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine) Note: VAG1921 spring clamp pliers are recommended for installation Always replace
11. CARBURETOR 11-0 CARBURETOR ZX / SCOUT 50
11 CARBURETOR SERVICE INFORMATION... 11-2 TROUBLESHOOTING... 11-2 THROTTLE VALVE DISASSEMBLY... 11-3 THROTTLE VALVE INSTALLATION... 11-4 CARBURETOR REMOVAL... 11-5 AUTO BYSTARTER... 11-6 FLOAT CHAMBER...
ENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.