Siphon Tipping Bucket & Operations & Maintenance Manual

Size: px
Start display at page:

Download "Siphon Tipping Bucket & Operations & Maintenance Manual"

Transcription

1 Siphon Tipping Bucket & Operations & Maintenance Manual Part No Revision C August 16, 2016

2 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg. 2 TABLE OF CONTENTS 1. Introduction Overview Specifications Installation Setup & Wiring Mounting Hole Pattern Theory of Operation Calibration Laboratory Calibration Field Calibration Maintenance Calibration Drip Setup Ordering Guide Training & Warranty... 11

3 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Introduction 1.1 Overview This Tipping Bucket Rain Gage is used to measure rainfall volume and/or rate. Rain entering through a funnel assembly with an 8.08 inch (205mm) orifice passes through a debris filtering screen and is funneled into a siphon that regulates flow and into one side of the tipping bucket assembly inside the gage. The bucket tips when a given amount of water, determined by gage calibration, has been collected. The model tips for each 0.2mm collected; the Model tips for each 0.5mm; the Model tips for each 0.01 inch (0.254 mm). As the bucket tips it causes a magnet to pass by a ruggedized reed switch, momentarily closing the switch. The tipping of the bucket brings a second bucket into position under the funnel, ready for filling. After the rain water is measured, it is directed into drain tubes that allow it to exit out holes in the base of the gage; the exit holes are 3/8 NPT to allow for tubing or screen fittings. Materials used in construction of the instrument are corrosion resistant. All external openings of the gage are protected from insects and foreign material by mesh screen. 2. Specifications Type Sensitivity/Resolution Orifice size Accuracy Bearings Insect protection Tipping Bucket 1 tip per 0.2 mm 1 tip per 0.5 mm 1 tip per mm (0.01 inch) 205 mm (8.08 inch) dia. ±2% from mm/hr ( in/hr) Sapphire jeweled bearings with hard stainless steel shaft Mesh screens Capacity 700 mm/hr (27.5 inch/hr) with ±5% Output Switch type Size Diameter Height Weight Temperature range, operating 0.1 second switch closure Single reed switch 228 mm (9 inch) dia. 482 mm (19 inch) 3kg (6.6 lbs) 0 to 60 C (32 F to 140 F)

4 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Installation 3.1 Setup & Wiring 1. This instrument is thoroughly tested and fully calibrated at the factory and is ready for installation. If return to the factory is necessary please contact the Sutron Customer Service department at (703) for a Return Material Authorization Number. 2. The gage must be mounted level and adequately protected from high winds. Errors of greater than 5% can occur due to rainfall blowing over the lip of the orifice. 3. Install the rain gage at a distance away from surrounding obstructions two to four times the obstacle's height. Such obstacles may block the normal rainfall path into the gage or rainfall may blow off the obstructions and into the gage. 4. The gage should be securely mounted by using the mounting holes provided by the mounting feet. A recommended method of mounting the gage is to secure the gage pour a small (12" square) concrete pad at the site with three anchor bolts set for the hole pattern of the mounting feet. 5. Loosen the 3 screws attaching the outer housing of the rain gage to the tipping bucket mechanism. Rotate the top half clockwise and lift up to remove outer housing of rain gage. 6. Using the bulls-eye level on the tipping bucket mechanism, level and securely mount the gage. 7. Fish a two conductor cable through the PG gland in the base and connect the two conductor cables between the Switch thumb screw and the screw on the housing to the right of the switch. Do this by unscrewing both screws from housing to create a gap about the thickness of the wire, stripping 1/2" of insulation off of both wires, wrap the stripped part around each screw clockwise between the gap, tighten down both screws to clamp the wire in place. For SDI-12 connections use a 3 conductor cable in the PG gland to SDI-12 interface and 2 short pieces of wires connected to switch and TB in and GND. Figure 1: Tipping Bucket Output Figure 2: SDI-12 Output 8. Pull extra cable back out the PG gland and tighten the gland to secure the cable in place. 9. Place the cover back on making sure to align with the screws in the base. Make a slight count-clockwise rotation once the cover is on the base and secure it in place by tightening all three screws in the base. 10. Be sure to remove any packing material and the bucket retainers from the instrument.

5 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Mounting Hole Pattern Use three 5/16-18 bolts to secure tipping bucket to installation platform. Drain holes are 3/8 NPT tapped for optional outlet filters or drainage tubing.

6 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Theory of Operation The 205 mm (8.08 inch) diameter orifice was chosen from a trade-off between the sampling area and the size of the tipping bucket mechanism. The large funnel at the orifice helps prevent evaporation inside the instrument. Precipitation enters the funnel inside the instrument and remains there until there is sufficient accumulation to trigger the siphon. This is about equal to 4mL worth of precipitation. Once the siphon is triggered, it releases all the water in the funnel at a constant rate and is directed to one of two tipping buckets. When one bucket fills, its weight tips the next bucket into position, and empties the first. At the same time, a.1 second momentary contact closure occurs. This closure initiates an event accumulating device. The water drains through the bottom of the instrument.

7 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Calibration 5.1 Laboratory Calibration Model Number Calibration Grams per Tip & mm of rain 6.62 grams & mm of rain grams & mm (0.01 ) of rain 8.40 grams 1. To calibrate the tipping bucket rain gage, remove the outer cover by first loosening the three screws at the base. BE SURE THE GAGE IS LEVEL, using the built-in bulls-eye level as an indicator. 2. To make the first rough adjustment, draw water into a B-D 20cc syringe and weigh out to grams indicated in the table above for the required model number on an ACCULAB (or equal) Model 121 precision weighing gage. Be sure to zero out the weight of the empty syringe before weighing the water. With the bucket adjustment screws located on the bottom of tipping bucket, adjusted all the way counter-clockwise, transfer the water from the syringe into one side of the bucket. Rotate the opposite side adjusting screw clockwise until the bucket tips. Repeat these steps for the second bucket. 3. To make the final calibration adjustments, reassembly the cover to the tipping bucket and devise a source of water (Calibration Drip Setup, page 8) with a uniform flow rate of approximately 50mm/hr (2"/hr). Direct this flow onto the wall of the small funnel. After the gage has tipped several times and the buckets are wet, collect the water in two containers, one under each drain tube. (Styrofoam cups work well) Carefully insert the collection containers between tips and collect exactly 5 tips of each bucket. Remove the containers. Measure the amount of water in each container by weight using the ACCULAB weighing gage described above. (Be sure to zero out the weight of the empty collection containers) The total weight of both containers should be from grams to grams, or + 2% of 84 grams if calibrating for a -6 unit. 4. Adjustments may be made to the stops located under the buckets. Raising the stop of the bucket will reduce the catch for that bucket and consequently lowering the stop will reduce the catch for that bucket and consequently lowering the stop will increase the catch. NOTE: The stop for a bucket is located under the opposite bucket. Make only small corrections at a time (1/4 turn per test). Repeat the calibration procedure until the gage is within specifications. 5. The above procedure is for a rate of 50mm/hr (2"/hr). The gage may be calibrated at other rates of interest. 6. After calibration, note date and place of calibration and reinstall the outer cover and screws. Be sure the cover is correctly lined up. 7. If the gage has been removed from a field location for calibration be sure the gage is installed and leveled properly.

8 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Field Calibration To check for calibration in the field, use a Nova Lynx, or equal, Rain Gauge Field calibrator Model An alternate is Allweatherinc, Model Bring at least 3 liters of roughly room temp water to the gage site for this test. Below is a table for Nova Lynx calibrator with 946 ml of water. Note that exceeding the instrument s specified accuracy range with a very high simulated rain rate will result in an under counting of the rain. A simulated rain rate exceeding the specified accuracy range defeats the benefit of the siphon resulting in water continuously running into the buckets. With water continuously running in, a little bit of water is lost during every tip transition. This error is more pronounced with smaller bucket sizes since there are more tips for a given amount of water. You can see the result of exceeding the specified accuracy range when testing at 26 in/hr in the table below. Orifice size Inches/hour mm/hr Test Time 1/ tips tips tips ~35 min 1/ min 3/ min 1/8 26* 660.4* min *Rain rate exceeds the specified calibration range. 1. For a calibration check at 2"/hr rate, fill the bottle with room temperature water until the meniscus level reaches the center of the reference line of 946 ml. Note that Nova Lynx calibrator embossed line may not be in the correct location. 2. Screw the orifice assembly onto the bottle and slip the holder over with the feet pointing upward. 3. While holding the calibrator over the gage, flip the calibrator assembly so that water begins flowing out into the rain gage funnel. Do not allow any water to drip outside the funnel. 4. Set the calibrator in the funnel shown in the diagram. The feet of the holder should position themselves firmly in the funnel, supporting the bottle nearly vertical above the funnel opening. 5. In about half an hour the water stream should cease. Tap or shake the bottle slightly to make sure all the water is out. 6. Repeat the above test about three times, recording the number of tips after each test. (Note: The number of tips during each test can vary ± 1 count or so because of the residual water left in one bucket and/or siphon at the end of the preceding test. 7. For 2"/hr rain rate the number of tips should be from 110 to 114 for -6 model. If the values fall below or above, remove the gage from the field and recalibrate using the Laboratory Calibration Check. Note that the siphon will prevent some water from going through the system so your tip count may reduce by 1 depending on whether you start with the unit completely dry or not. 5.3 Maintenance Maintenance is limited to cleaning debris out of the input orifice and output drains.

9 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Calibration Drip Setup W ater Container Flow Meter -- Gilmont Instruments or Equivalent Adjusts Flow Rate Tipping Bucket Mechanism F i g. 2

10 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Ordering Guide Sutron Tipping Buckets & Accessories mm Tipping bucket mm Tipping bucket with SDI-12 output mm Tipping bucket mm Tipping Bucket with SDI-12 output inch (0.254 mm) Tipping Bucket inch (0.254 mm) Tipping Bucket with SDI-12 output SDI-TB-1 SDI-12 Interface electronics, comes standard on X units. You can field upgrade an X model into a X inch Stainless Steel Filter screen Pipe mounting kit

11 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg Training & Warranty Dear Customer: Thank you for making the important decision to purchase Sutron equipment. All Sutron equipment is manufactured and tested to the highest quality standards as set by Sutron s Quality Assurance Department. Our Customer Service Representatives have years of experience with equipment, systems and services. We have electronic technicians with field and applications experience, not limited to technical school training. Sutron Equipment Repairs Sutron maintains a Repair Department at the Virginia factory (22400 Davis Drive, Sterling, VA 20164). Average turn-around time for repairs ranges from ten to thirty days after Sutron receives equipment for repair. Prior to returning any equipment for repair, please call Customer Service at (703) for a Return Material Authorization (RMA) number. Then send the faulty equipment back to the Virginia factory**. Sutron Customer Service will repair Sutron-manufactured equipment sent to us for repair within 30 days of the time we receive the item or that repair is free of charge.* Please provide our Customer Service Representative with your address when receiving the RMA number so that we can you when your equipment is received at Sutron and again when it is shipped back to you. Expedited repairs can be completed within one (1) week for an additional expedite fee of $ Repaired equipment is warranted for a period of 180 days after the repair shipment date.*** We appreciate your cooperation in achieving a quick turn-around by promptly providing cost approval decisions, Purchase Order and credit card information once we have supplied you with a repair estimate. Customer Phone Support: 8:00 am to 8:00 pm EST, Monday through Friday Customer Service Representatives routinely handle a wide variety of questions every day. When equipment questions arise, please feel free to contact me or one of Sutron s Customer Service Representatives. We are available from 8:00 am to 8:00 pm EST Monday through Friday and are happy to take your calls. The main Customer Service number is (703) , extension #5. After 5 pm EST Monday through Friday, please use extension #6. We typically answer most datalogger, transmitter, sensor and interface questions on the first call. If we cannot quickly answer a question on an interface, we will work with you until we find a solution. Sometimes a problem is application related. Although we pride ourselves on handling 95% of application related questions over the phone, we maintain constant contact with our Integrated Systems Division and Engineering Division for additional assistance.

12 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg. 12 On-Site Visits Of course not all problems can be fixed over the phone. Sometimes a customer needs an on-site technician to identify site related problems or troubleshoot a network. Sutron provides these services at a reasonable cost. Please call for details. Training Training is an important part of the Sutron Customer Service Success policy. With proper training, you will learn how to take advantage of all the benefits and tools that Sutron equipment provides. We are available for, and frequently provide, on-site introductory training at our Customers facilities. We also hold three (3) day training seminars approximately four times per year at our Sutron headquarters in Sterling (near Washington, DC). Contact me or your Sutron Regional Sales Manager for details. If you would like to learn more about Sutron products, please sales@sutron.com. Thank you again for your business, Paul Delisi, Customer Service Manager pdelisi@sutron.com * Note: The 30 day guarantee applies only to Sutron-manufactured products. The 30 day guarantee does not apply to the following: bulk shipments of 10 or more repair items, third party or buy-ship products, shipments awaiting payment authorizations, cases where delays are caused by international customs, shipping or other regulations. Additionally, the 30 day guarantee is exclusive of domestic and international transit times.* ** Transportation charges for equipment returns are the responsibility of the Customer. *** See Warranty.Any products repaired or replaced under Warranty will be warranted for the balance of the Warranty period or for a period of 180 days from the repair shipment date, whichever is greater.

13 Sutron Corporation Tipping Bucket Rev. C Operations & Maintenance Manual 8/17/2016 pg. 13 COMMERCIAL WARRANTY SUTRON MANUFACTURED EQUIPMENT THE SUTRON CORPORATION WARRANTS that the equipment manufactured by its Manufacturing Division shall conform to applicable specifications and shall remain free from defects in workmanship and material for a period ending two years from the date of shipment from Sutron s plant. Sutron s obligation under this Warranty shall be limited to repair at the factory (22400 Davis Drive, Sterling, VA 20164) or, at Sutron s option, replacement of the defective product. In no event shall Sutron be responsible for incidental or consequential damages, whether or not foreseeable or whether or not Sutron has knowledge of the possibility of such damages. This Warranty shall not apply to products that have been damaged through negligence, accident, misuse or acts of nature such as floods, fires, earthquakes, lightning strikes, etc. Sutron s liability, whether in contract or in tort, arising out of warranties or representations, instructions or defects from any cause, shall be limited exclusively to repair or replacement parts under the aforesaid conditions. Sutron requires the return of the defective electronic products or parts to the factory to establish claim under this Warranty. The customer shall pre-pay transportation charges to the factory. Sutron shall pay transportation charges for the return of the repaired equipment to the customer when the validity of the damage claim has been established. Otherwise, Sutron will pre-pay shipment and bill the amount to the customer. All shipments shall be accomplished by best-way surface freight. Sutron shall in no event assume any responsibility for repairs or alterations made other than by Sutron. Any products repaired or replaced under this Warranty will be warranted for the balance of the Warranty period or for a period of 180 days from the repair shipment date, whichever is greater. Products repaired at cost will be warranted for 90 days from the date of shipment. NON-SUTRON MANUFACTURED EQUIPMENT The above Warranty applies only to products manufactured by Sutron. Equipment provided, but not manufactured by Sutron, is warranted and will be repaired to the extent of and according to the current terms and conditions of the respective equipment manufacturers. EXTENDED WARRANTY AND ON-SITE MAINTENANCE Extended warranty and on-site maintenance contracts are available. Price quotations may be obtained from Sutron Customer Service Representatives.

Data-Logging Rain Gauge PRODUCT MANUAL

Data-Logging Rain Gauge PRODUCT MANUAL Data-Logging Rain Gauge PRODUCT MANUAL Item # 3554WD1 Thank you for purchasing a Spectrum Datalogging Rain Gauge. With proper installation and care, it will give you years of accurate and reliable measurements.

More information

RS-110 Rainfall Sensor Installation Guide

RS-110 Rainfall Sensor Installation Guide RS-110 Rainfall Sensor Installation Guide for XR440 and XR5 Data Loggers September 2015 Revision 1.1 1 Disclaimer The following warranty and liability disclaimer apply to this product. PACE SCIENTIFIC

More information

Rain Gauge Smart Sensor (Part # RGA-M0XX, RGB-M0XX)

Rain Gauge Smart Sensor (Part # RGA-M0XX, RGB-M0XX) (Part # RGA-M0XX, RGB-M0XX) The Rain Gauge smart sensor is designed to work with the HOBO Weather Station logger. The smart sensor has a plug-in modular connector that allows it to be added easily to a

More information

METEOROLOGICAL INSTRUMENTS

METEOROLOGICAL INSTRUMENTS METEOROLOGICAL INSTRUMENTS INSTRUCTIONS PRECIPITATION GAUGE MODEL 50202 / 50203 R.M. YOUNG COMPANY 2801 AERO PARK DRIVE, TRAVERSE CITY, MICHIGAN 49686, USA TEL: (231) 946-3980 FAX: (231) 946-4772 WEB:

More information

Rain Collector (#7857 & 7857M)

Rain Collector (#7857 & 7857M) Rain Collector (#7857 & 7857M) This rain collector can be used with Vantage Pro2 weather stations, including Vantage Pro2, Vantage Pro2 Plus, and the Anemometer/Sensor Transmitter Kit. The following instructions

More information

TR-4 Tipping Bucket Rain Gauge User s Manual

TR-4 Tipping Bucket Rain Gauge User s Manual Relied on Worldwide in the Most Extreme Conditions TR-4 Tipping Bucket Rain Gauge User s Manual Texas Electronics, Inc. Dallas, TX 75237 Fax.214.631.4218 4230 Shilling Way Tel.214-631-2490 www.texaselectronics.com

More information

INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL HS305

INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL HS305 INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL HS305 HS305 100-01 CONTENTS Page I General HS305 100-03 II Specification HS305 100-03 III Installation HS305 100-04 IV Test Operation HS305 100-05 V Maintenance

More information

INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL HS305

INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL HS305 INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL HS305 QUALITY SYSTEM ISO 9001 2008 CERTIFIED HYQUEST SOLUTIONS PTY. LTD. PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) +612 9601 2022 Fax:

More information

Operating Instructions

Operating Instructions Operating Instructions WARNING: Do not attempt to assemble, connect to power source, or operate the Burrell Wrist-Action Shaker without first reading these instructions. Also assure that each person that

More information

ONE-YEAR SERVICE AND FREIGHT WARRANTY GUIDELINES

ONE-YEAR SERVICE AND FREIGHT WARRANTY GUIDELINES ONE-YEAR WARRANTY This One-year Warranty ( Warranty ) applies to new systems purchased from and installed by a MotoSAT Factory Certified Installer ( Installer ). To receive the benefits of this Warranty,

More information

Digital Body Weight Scale Model No.: EB4074C. Questions or Concerns? (855)

Digital Body Weight Scale Model No.: EB4074C. Questions or Concerns? (855) Digital Body Weight Scale Model No.: EB4074C Questions or Concerns? (855) 686-3835 support@etekcity.com 1 Thank You. Thank you for purchasing the EB4074C Digital Body Weight Scale by Etekcity. We are dedicated

More information

AD-7 THERMAL INDICATING AMMETER

AD-7 THERMAL INDICATING AMMETER AD-7 THERMAL INDICATING AMMETER a nd ACCESSORIES Operating & Instruction Manual HD ELECTRIC COMPANY 1 4 7 5 L A K E S I D E D R I V E W A U K E G A N, I L L I N O I S 6 0 0 8 5 U. S. A. P H O N E 8 4 7.

More information

WARRANTY POLICY. Grid-Tied Photovoltaic Inverters. Revision D. 2014, Solectria Renewables, LLC DOCIN

WARRANTY POLICY. Grid-Tied Photovoltaic Inverters. Revision D. 2014, Solectria Renewables, LLC DOCIN WARRANTY POLICY Revision D 2014, Solectria Renewables, LLC DOCIN-070360 1 Product Warranty & RMA Policy 1. Warranty Policy Warranty Registration: It is important to have updated information about the inverter

More information

PVI 60KW, PVI 82KW, PVI 95KW

PVI 60KW, PVI 82KW, PVI 95KW PVI 60KW PVI 82KW PVI 95KW WARRANTY MANUAL Commercial, Grid-Tied Photovoltaic Inverters 2008, Solectria Renewables LLC Subject to Change DOC-020099 rev 024 1 1 Product Warranty & RMA Policy Warranty Policy

More information

DATA LOGGING RAIN GAUGE MANUAL Part # RG2 and RG2-M

DATA LOGGING RAIN GAUGE MANUAL Part # RG2 and RG2-M DATA LOGGING RAIN GAUGE MANUAL Part # RG2 and RG2-M 5470-B MAN RG2/RG2-M Tel: 1-800-LOGGERS, 1-508-759-9500 Fax: 1-508-759-9100, www.onsetcomp.com Contents Rain gauge overview... 2 Accessing the logger...

More information

Digital Body Weight Scale Model No. EB4074C. Questions or Concerns? (855)

Digital Body Weight Scale Model No. EB4074C. Questions or Concerns? (855) Digital Body Weight Scale Model No. EB4074C Questions or Concerns? (855) 686-3835 support@etekcity.com Thank you for purchasing the Digital Body Weight Scale by Etekcity. This device can help you reach

More information

Rapid Shrink 100. Owner s Manual

Rapid Shrink 100. Owner s Manual Rapid Shrink 100 Owner s Manual Table of Contents Introduction Pg. 2 General Safety Pg. 3-4 Which Tank to Use Pg. 5-6 Operating Instructions Pg. 7-10 Troubleshooting Guide Pg. 11-12 Parts Index Pg. 13-14

More information

Digital Body Weight Scale

Digital Body Weight Scale Digital Body Weight Scale Model No.: EB4410B Questions or Concerns? Please contact us: (855) 686-3835 support@etekcity.com Thank You. Thank you for purchasing the Digital Body Weight Scale by Etekcity.

More information

Digital Tipping Bucket Rain Collector PRODUCT MANUAL

Digital Tipping Bucket Rain Collector PRODUCT MANUAL Digital Tipping Bucket Rain Collector PRODUCT MANUAL Item # 3665RD 2 THANK YOU for purchasing a Digital Rain Collector to use with your WatchDog Sensor Pups. This manual will aid you in placement and mounting

More information

"WHERE TUBING AND FITTINGS COME TOGETHER"

WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD200SS TUBE EXPANDER OPERATIONS MANUAL VERSION 4.3 LAST EDITED 06.17.15 cleanroomdevices.com Table of Contents Table of Contents....1

More information

Model Combustible Gas Sample Draw Detector Head Operator s Manual

Model Combustible Gas Sample Draw Detector Head Operator s Manual Model 1017-06 Combustible Gas Sample Draw Detector Head Operator s Manual Part Number: 71-0356 Revision: P1 Released: 2/4/15 www.rkiinstruments.com WARNING Read and understand this instruction manual before

More information

Dear Customer, User Memo: Please visit us on facebook or twitter! Thank you for purchasing this product.

Dear Customer, User Memo: Please visit us on facebook or twitter! Thank you for purchasing this product. Owner s Manual 1 Dear Customer, Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. User Memo: Date of purchase: Dealer name: Dealer address:

More information

Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions

Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions Revision 012211 Table of Contents Basic Conveyor Features 3 Getting Started 4 Setting Up the Incline Conveyor 5 Belt Removal

More information

Techcon Systems TS5000 Series Rotary Valve

Techcon Systems TS5000 Series Rotary Valve 10. SPARE PARTS AND ACCESSORIES 10.1 SPARE PARTS: The only spare parts available are: Fluid inlet fitting, O- ring and clean out screw. These items are included in the Valve cleaning kit part number: 5000-013-000

More information

Web Volume Control Model WV220

Web Volume Control Model WV220 WEB CONTROL PRODUCTS User Manual Web Volume Control Model WV220 1 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject

More information

Installation, Operating and Maintenance instructions for Hydro-Air pumps

Installation, Operating and Maintenance instructions for Hydro-Air pumps FEATURES: Installation, Operating and Maintenance instructions for Hydro-Air pumps USE & APPLICATION: INSTALLATION: The pump is a magnetically driven centrifugal water pump. It has no seals to wear and

More information

UPPER TRAILING ARM REMOVAL

UPPER TRAILING ARM REMOVAL #1204 MUSTANG UPPER TRAILING ARMS Thank you for your purchase. Please call us at (562) 907-7757 if you have any questions regarding your Hotchkis Performance products. Visit us online @ www.hotchkis.net

More information

Model Combustible Gas Sample Draw Detector Head Operator s Manual

Model Combustible Gas Sample Draw Detector Head Operator s Manual Model 1017-07 Combustible Gas Sample Draw Detector Head Operator s Manual Part Number: 71-0480 Revision: P1 Released: 1/4/19 www.rkiinstruments.com WARNING Read and understand this instruction manual before

More information

COMPRESSED AIR LOADER MODEL: AL-1

COMPRESSED AIR LOADER MODEL: AL-1 COMPRESSED AIR LOADER MODEL: AL-1 Document: AL-1 IM 10-22-2011 TABLE OF CONTENTS Important Notices and Precautions 3 Quick Installation 4 Product Description 4 Principle of Operation 5 Unpacking and Inspection

More information

Model Combustible Gas Sample Draw Detector Head Operator s Manual

Model Combustible Gas Sample Draw Detector Head Operator s Manual Model 1017-01 Combustible Gas Sample Draw Detector Head Operator s Manual Part Number: 71-0058RK Revision: B Released: 5/24/13 www.rkiinstruments.com WARNING Read and understand this instruction manual

More information

SoilStik ph Meter PRODUCT MANUAL. Item # 2105

SoilStik ph Meter PRODUCT MANUAL. Item # 2105 SoilStik ph Meter PRODUCT MANUAL Item # 2105 Contents General Overview...3 LCD Display...4 LCD Display Messages...5 Meter Components...6 Calibration...7 Changing the Temperature Units...8 Taking Liquid/Soil

More information

Professional Weather Center

Professional Weather Center Instruction Manual Professional Weather Center CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2... 3... 4... 6 Setup... 7 5-in-1 Sensor Setup... 7... 8... 9... 9...10...

More information

Kalyx-RG Rain Gauge User Manual

Kalyx-RG Rain Gauge User Manual Kalyx-RG Rain Gauge User Manual PUBLISHED BY Environmental Measurements Limited (EML) 7 Jupiter Court Orion Business Park North Shields NE29 7SE United Kingdom Visit our internet pages at http://www.emltd.net

More information

FCB-450, LCB-600, MCB-800

FCB-450, LCB-600, MCB-800 AIR CHAMP PRODUCTS User Manual FCB-450, LCB-600, MCB-800 Clutch-Brakes (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are

More information

Techcon Systems TS7000 Series Interchangeable Material Path Rotary Valve

Techcon Systems TS7000 Series Interchangeable Material Path Rotary Valve Techcon Systems TS7000 Series Interchangeable Material Path Rotary Valve User Guide Copyright OK International CONTENTS Page number 1. Specifications 3 2. Unpacking and inspection 4 3. Description 4 4.

More information

Operation Instructions

Operation Instructions Rice Lake Mechanical Physician Scale (w/ hand post) Model RL-MPS-30 Operation Instructions 132702 Contents 1.0 Introduction... 1 2.0 Installation Instructions... 2 2.1 Pillar Installation.................................................................

More information

Product Recovery Canister

Product Recovery Canister Product Recovery Canister Installation and Operation Manual PRC 2 PRC 4 Rev. 4/28/2010 Part # 26650319 TABLE OF CONTENTS CHAPTER 1: SYSTEM DESCRIPTION... 5 FUNCTION AND THEORY... 5 SYSTEM COMPONENTS...

More information

ETgage Model E Instructions

ETgage Model E Instructions EXTERNAL WIRING Unclip and drop down the bottom compartment of the instrument to expose the circuit board. Insert lead-in wires through the 3/16-inch diameter hole in the side of the instrument, and through

More information

Operation Instructions

Operation Instructions Rice Lake Mechanical Physician Scale Model RL-MPS, RL-MPS-10, RS-MPS-20 Operation Instructions To be the best by every measure 102696 Contents 1.0 Introduction... 1 2.0 Installation Instructions... 2

More information

CM1000C CM1800C ChangeMakers. Operator s Manual. Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA

CM1000C CM1800C ChangeMakers. Operator s Manual. Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA CM1000C CM1800C ChangeMakers Operator s Manual Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA 61032 www.seagamfg.com INTRODUCTION Congratulations on the purchase of your new ChangeMaker. This

More information

AUTO-BLiP. User Manual Porsche INTELLIGENT DOWNSHIFTS. Version 1.2

AUTO-BLiP. User Manual Porsche INTELLIGENT DOWNSHIFTS.   Version 1.2 AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 2005+ Porsche Version 1.2 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP while driving

More information

Andatech SOBERPOINT 3. Wall Mounted Breathalyser USER S MANUAL

Andatech SOBERPOINT 3. Wall Mounted Breathalyser USER S MANUAL Andatech SOBERPOINT 3 Wall Mounted Breathalyser USER S MANUAL Thank you for purchasing an Andatech Soberpoint 3 breathalyser. The Andatech Soberpoint 3 is a Fuel Sensor type coin- or buttonoperated breathalyser.

More information

Stainless Steel Pilot Piston Solenoid Valve 2MS Series for High Temperature & High Pressure

Stainless Steel Pilot Piston Solenoid Valve 2MS Series for High Temperature & High Pressure Stainless Steel Pilot Piston Solenoid Valve 2MS Series for High Temperature & High Pressure S T C TM To Order, Please Specify: 1) Model No., 2) Voltage 2 Way, NC Pilot Piston Stainless Steel Part No. Voltage

More information

AXD 530 MicroManometer

AXD 530 MicroManometer OWNER S MANUAL AXD 530 MicroManometer A TSI Company Table of Contents Features 2 Using the AXD530 Safely 3 Getting Started 4 Installing Batteries 4 Preparing the Instrument 4 Attaching the Optional Pitot-Static

More information

Radian Research, Inc. makes no warranty on the accuracy of the information contained in this Operations Manual and accepts no liability for its use.

Radian Research, Inc. makes no warranty on the accuracy of the information contained in this Operations Manual and accepts no liability for its use. About This Operations Manual makes no warranty on the accuracy of the information contained in this Operations Manual and accepts no liability for its use. The information contained in this Operations

More information

Model E600 Tarping System

Model E600 Tarping System 10 Boulder Parkway N. Oxford, MA 01537 866-353-5826 pioneersales@wastequip.com www.pioneercoverall.com Model E600 Tarping System Installation Instructions WARNING: In order to prevent damage, the tarp

More information

STC 2P025 Series Solenoid Valve

STC 2P025 Series Solenoid Valve STC 2P025 Series Solenoid Valve 2P025 Series Solenoid Valve Specifications Valve Model Valve Type Action Cv (Orifice) Operating Pressure Operating Temperature 2P025 2 Way, Normally Closed (NC) Direct Acting

More information

AD-7. Instruction Manual. Thermal Indicating Ammeter HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS U.S.A.

AD-7. Instruction Manual. Thermal Indicating Ammeter HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS U.S.A. CONTROLS & SYSTEM MEASUREMENT AD-7 Thermal Indicating Ammeter Instruction Manual HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS 60085 U.S.A. PHONE 847.473.4980 FAX 847.473.4981 website: www.hdelectriccompany.com

More information

L007 LIQUID LEVEL FLOAT SWITCH. Side-Mounted Liquid Level Float Switch INSTALLATION AND OPERATIONS MANUAL

L007 LIQUID LEVEL FLOAT SWITCH. Side-Mounted Liquid Level Float Switch INSTALLATION AND OPERATIONS MANUAL L007 LIQUID LEVEL FLOAT SWITCH INSTALLATION AND OPERATIONS MANUAL Side-Mounted Liquid Level Float Switch READ THIS MANUAL PRIOR TO INSTALLATION This manual provides information on the L007 Side- Mounted

More information

STC 2L Series Solenoid Valves

STC 2L Series Solenoid Valves STC 2L170-500 Series Solenoid Valves 2L170-500 Series Solenoid Valve Specifications Valve Model 2L170-3/8 2L170-1/2 2L170-3/4 2L200-1 2L300-1 1/2 2L500-2 Valve Type Action 2 Way, Normally Closed (NC) Pilot

More information

PVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables

PVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables PVI 1800/PVI 2500 WARRANTY MANUAL Residential/Commercial Grid-Tied Photovoltaic Inverter 2009, Solectria Renewables Subject to Change REV 10.09 1 Product Warranty & RMA Policy 1.1 Warranty Policy The Solectria

More information

Model 1100 Turbine Flow Meter

Model 1100 Turbine Flow Meter Model 1100 Turbine Flow Meter INSTALLATION & INSTRUCTION MANUAL 8635 Washington Avenue Racine, Wisconsin 53406 Tel: 800-433-5263 or 262-639-6770 Fax: 800-245-3569 or 262-639-2267 www.hedland.com TABLE

More information

MODEL 1100 TURBINE FLOW METER

MODEL 1100 TURBINE FLOW METER MODEL 1100 TURBINE FLOW METER INSTALLATION & INSTRUCTION MANUAL 8635 Washington Ave. Racine, Wisconsin 53406 Phone: 800.433.5263 Fax: 800.245.3569 www.hedland.com 2 OPERATIONAL START-UP Fluid entering

More information

1416 Cabinet Unit. Installation Operation Maintenance Troubleshooting Version Dec/17

1416 Cabinet Unit. Installation Operation Maintenance Troubleshooting Version Dec/17 Installation Operation Maintenance Troubleshooting Version Dec/17 1416 Cabinet Unit Page 1 of 16 Table of Contents Important Information... 3 Weight & Dimensions... 4 Operator s Instructions... 5 Flow

More information

INTRODUCTION INSTALLATION

INTRODUCTION INSTALLATION INTRODUCTION INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS This instruction manual includes installation, operation and maintenance information for the figure G73 gear operator. The figure G73 is

More information

3V SERIES SOLENOID VALVE

3V SERIES SOLENOID VALVE 3V110-410 SERIES SOLENOID VALVE Valve Model 3V110-1/8 3V210-1/4 3V310-3/8 3V410-1/2 Port & Mounting Action & Motion Operating Pressure Body Ported Air Pilot, Spool Design, Response Time

More information

L-Series: LIQUID LEVEL FLOAT SWITCH. Single-Point, Vertically-Mounted Liquid Level Float Switch INSTALLATION AND OPERATIONS MANUAL

L-Series: LIQUID LEVEL FLOAT SWITCH. Single-Point, Vertically-Mounted Liquid Level Float Switch INSTALLATION AND OPERATIONS MANUAL L-Series: L001, L002, L003, L170, L175, L176, L177, L178, L180, L190 AND L195 LIQUID LEVEL FLOAT SWITCH INSTALLATION AND OPERATIONS MANUAL Single-Point, Vertically-Mounted Liquid Level Float Switch L001

More information

INSTRUCTIONS AND SERVICE MANUAL WITH PARTS LIST

INSTRUCTIONS AND SERVICE MANUAL WITH PARTS LIST CMP SERIES CPM15-15B (25905F300) CPM15-15B-H/D (25905F301) CPM18-15B (25905F303) CPM18-15B-H/D (25905F304) INDUSTRIAL PUMPS INSTRUCTIONS AND SERVICE MANUAL WITH PARTS LIST NOTE! To the installer: Please

More information

Rain Gauge RG13 and RG13H USER'S GUIDE

Rain Gauge RG13 and RG13H USER'S GUIDE Rain Gauge RG13 and RG13H USER'S GUIDE D210220EN-A April 2004 PUBLISHED BY Vaisala Oyj Phone (int.): +358 9 8949 1 P.O. Box 26 Fax: +358 9 8949 2227 FIN-00421 Helsinki Finland Visit our Internet pages

More information

Rapid Digestor Fume Removal System

Rapid Digestor Fume Removal System Rapid Digestor Fume Removal System Model 23500-20 Designed for 20 Place Block Digestors Model 23500-25 Designed for Rapid Digestor 25 Place Model 23540 Designed for Rapid Digestor 4 Place INSTRUCTION MANUAL

More information

Model Series 66 Amplifying and Reducing Relays

Model Series 66 Amplifying and Reducing Relays Siemens Energy & Automation INSTALLATION AND SERVICE INSTRUCTION INTRODUCTION Model Series 66 Amplifying and Reducing Relays SD66 Rev 11 January 2006 Supersedes Rev 10 The Model Series 66 Amplifying and

More information

AIR CHAMP PRODUCTS. User Manual. Sheave & Pilot Mount Clutch-Brake Model BCB-275 FORM NO. L F-0414 FORM NO. L F-0414

AIR CHAMP PRODUCTS. User Manual. Sheave & Pilot Mount Clutch-Brake Model BCB-275 FORM NO. L F-0414 FORM NO. L F-0414 AIR CHAMP PRODUCTS User Manual Sheave & Pilot Mount Clutch-Brake Model BCB-275 i In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual

More information

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09 HAND CRANK & MOTORIZED POWER CORD REELS: SERIES 1125PC SERIES: 1125PC HAND CRANK SERIES: 1125PC MOTORIZED COXREELS The technical data and images which appear in this manual are for informational purposes

More information

Flo-Way. Measure Granular or Powdered Material. Stand Alone or Connect to Other Devices for Blending. Used by Successful Producers World-Wide

Flo-Way. Measure Granular or Powdered Material. Stand Alone or Connect to Other Devices for Blending. Used by Successful Producers World-Wide Flo-Way R Solids Impact Flow Meter Measure Granular or Powdered Material Stand Alone or Connect to Other Devices for Blending Used by Successful Producers World-Wide Visit our website: www.beltwayscales.com

More information

II DISTRIBUTION & SUBSTATION TYPE C

II DISTRIBUTION & SUBSTATION TYPE C CapCheckIII DISTRIBUTION & SUBSTATION TYPE Ca p a c i t o r C h e c ke r Operating & Instruction Manual 1475 Lakeside Drive Waukegan, Illinois 60085 U.S.A. 847.473.4980 f a x 8 4 7. 4 7 3. 4 9 8 1 w e

More information

DWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers

DWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers DWS404 DWS524 DWS654 DWS684 DWS694 DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers PREPARATION Safety Guidelines Thank you for purchasing the DWS Series car speakers. Although Dual has attempted

More information

Effective June 1, 2013 This guide supersedes all previous versions

Effective June 1, 2013 This guide supersedes all previous versions Effective June 1, 2013 This guide supersedes all previous versions 3842 Redman Drive 1-800-797-7974 Fort Collins, CO 80524 www.commandlight.com L-CAS THANK YOU Please allow us to express a simple thank

More information

Positive Displacement Pump

Positive Displacement Pump www.conairgroup.com U S E R G U I D E UGC028-1105 Positive Displacement Pump Models PD 3. 5, 7.5, 10, 15 and 25 Corporate Office: 724.584.5500 l Instant Access 24/7 (Parts and Service): 800.458.1960 l

More information

ADI-125/750 ADI-125/1500 ADI-125/2500

ADI-125/750 ADI-125/1500 ADI-125/2500 Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com 121094B OWNERS

More information

Model GD-K77D4X-XX Supplement to the GD-K77D Operator s Manual

Model GD-K77D4X-XX Supplement to the GD-K77D Operator s Manual Model GD-K77D4X-XX Supplement to the GD-K77D Operator s Manual Part Number: 71-0217RK Revision: 0 Released: 3/1/11 www.rkiinstruments.com WARNING Read and understand this instruction manual before operating

More information

Loctite 300ml Cartridge Pusher Part Number EQUIPMENT Operation Manual

Loctite 300ml Cartridge Pusher Part Number EQUIPMENT Operation Manual Loctite 300ml Cartridge Pusher Part Number 98022 EQUIPMENT Operation Manual Table Of Contents 1 PLEASE OBSERVE THE FOLLOWING... 3 1.1 EMPHASIZED SECTIONS...3 1.2 FOR YOUR SAFETY...3 1.3 ITEMS SUPPLIED...3

More information

4V130P-430P SERIES AIR PILOT VALVE

4V130P-430P SERIES AIR PILOT VALVE 4V130P-430P SERIES AIR PILOT VALVE Valve Model 4V130P-1/8 4V230P-1/4 4V330P-3/8 4V430P-1/2 Port & Mounting Action & Motion Operating Pressure Body Ported Double Solenoid, Spool Design, 3 Position, Pressure

More information

ActuLink ABS Module - ABS-MOD-400

ActuLink ABS Module - ABS-MOD-400 Installation Instructions ActuLink ABS Module - ABS-MOD-400 For more information on the installation and operation of Tuson s towable ABS system, consult the installation and operations manuals for the

More information

SSI Technologies MediaSensor

SSI Technologies MediaSensor SSI Technologies MediaSensor P51 Pressure Transducers Product Description SSI s line of bulk micro-machined, absolute and gage pressure transducers and transmitters for both harsh and benign media with

More information

NOVALYNX CORPORATION MODEL 200-WS-02F WIND SPEED & DIRECTION SENSOR INSTRUCTION MANUAL

NOVALYNX CORPORATION MODEL 200-WS-02F WIND SPEED & DIRECTION SENSOR INSTRUCTION MANUAL NOVALYNX CORPORATION MODEL 200-WS-02F WIND SPEED & DIRECTION SENSOR INSTRUCTION MANUAL REVISION DATE: MAY 2005 Receiving and Unpacking Carefully unpack all components and compare to the packing list. Notify

More information

BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer

BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer PREPARATION Getting Started Thank you for purchasing the Dual BAK1500 compact amplified subwoofer. Although Dual has attempted to ensure

More information

JET METER INSTRUCTIONS

JET METER INSTRUCTIONS UNPACKING Please open and inspect your package upon receipt. Your package was packed with great care and all the necessary packing materials to arrive to you undamaged. If you do find an item that is broken

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS OWNER S MANUAL FLO-MASTER XP2 SERIES PUMPS IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

More information

ST-70 CONTROL OPERATING MANUAL REVISION DATE: PART#:

ST-70 CONTROL OPERATING MANUAL REVISION DATE: PART#: ST-70 CONTROL OPERATING MANUAL REVISION DATE: 05-15-07 PART#: 98-0002-09 SERVICE & CUSTOMER INFORMATION CUSTOMER MUST HAVE PART NUMBER WHEN ORDERING ITEMS THROUGH THE SERVICE DEPARTMENT. IF FURTHER HELP

More information

RENA AF371Feeder Operating Manual. Feeder. Operating Manual. Manual Part #: M AF371 Operations Rev

RENA AF371Feeder Operating Manual. Feeder. Operating Manual. Manual Part #: M AF371 Operations Rev Manual Part #: M-3022 Feeder AF371 Operations Rev. 3-16-04 1 RENA AF371 Feeder YOUR RENA AF371 IS DISTRIBUTED BY RENA SYSTEMS INC. SERVICE AND SUPPORT FOR THIS PRODUCT IS PROVIDED BY YOUR RENA DEALER.

More information

STC 2W Series Solenoid Valves

STC 2W Series Solenoid Valves STC 2W160-500 Series Solenoid Valves 2W160-500 Series Solenoid Valve Specifications Valve Model 2W160-3/8 2W160-1/2 2W200-3/4 2W250-1 2W350-1 1/4 2W400-1 1/2 2W500-2 Valve Type Action 2 Way, Normally Closed

More information

Premium Pond Pump 330 Gallons Per Hour

Premium Pond Pump 330 Gallons Per Hour Premium Pond 330 Gallons Per Hour REMINDER CALL 1-888-755-4497 BEFORE RETURNING TO STORE. MODEL #PDP330 Questions, problems, missing parts? Before returning to your retailer, call our customer service

More information

Installation and Set Up Instructions

Installation and Set Up Instructions SL SLIDING GATE MOTOR KIT Solar Powered and 12V Low Voltage Installation and Set Up Instructions Unit 27 / 49 Corporate Boulevard Bayswater Vic 3153 Phone 1800 111 930 Email info@gforceautogates.com.au

More information

Installation Instructions

Installation Instructions 85-4592 rev. 08 02-18 Installation Instructions Thank you for purchasing our sway bar kit. Please read through these instructions before installation. Auxiliary Rear Anti-Sway Bar Kit for Ford F53 part

More information

Exhaust Fan Flow Meter. Operation Manual. The ENERGY CONSERVATORY DIAGNOSTIC TOOLS TO MEASURE BUILDING PERFORMANCE

Exhaust Fan Flow Meter. Operation Manual. The ENERGY CONSERVATORY DIAGNOSTIC TOOLS TO MEASURE BUILDING PERFORMANCE Exhaust Fan Flow Meter Operation Manual The ENERGY Exhaust Fan Flow Meter Operation Manual The Energy Conservatory 2801 21st Ave. S., Suite 160 Minneapolis, MN 55407 612-827-1117 Fax 612-827-1051 www.energyconservatory.com

More information

RT404-FLEX II ROTARY TABLE OPERATING MANUAL

RT404-FLEX II ROTARY TABLE OPERATING MANUAL P/N 561447 REV E AUG. 03 REV D NOV. 01 REV C APR. 01 REV B JULY 98 REV A AUG. 97 AUGUST 2003 RT404-FLEX II ROTARY TABLE OPERATING MANUAL 2003 I&J FISNAR INC. RT404-FLEX II ROTARY TABLE NOTE: Unlike the

More information

DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR

DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR OPERATION MANUAL DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR P/N 95-030 NIS -800-662-200 nissantechmate.com CONTENTS Specifications / Warranty... Functions...2-3 Accessories... 4 Set-Up... 5 Adaptor Installation...

More information

MICROPROCESSOR CONTROL WATER SUPPLY SYSTEM (MPR-01AW)

MICROPROCESSOR CONTROL WATER SUPPLY SYSTEM (MPR-01AW) MICROPROCESSOR CONTROL WATER SUPPLY SYSTEM (MPR-01AW) Installation, Operation, and Maintenance Manual REV. "B" REV. "C" PLEASE READ ENTIRE DOCUMENT BEFORE PROCEEDING WITH INSTALLATION Energy Saver has

More information

Container Fountain Kit with LED Light

Container Fountain Kit with LED Light Container Fountain Kit with LED Light REMINDER CALL 1-888-755-6750 BEFORE RETURNING TO STORE. PACKAGE CONTENTS Questions, problems, missing parts? Before returning to your retailer, call our customer service

More information

MODEL 200 MULTI-JET FLOW METER

MODEL 200 MULTI-JET FLOW METER MODEL 200 MULTI-JET FLOW METER - For Water Applications - INSTALLATION & INSTRUCTION MANUAL 8635 Washington Avenue Racine, Wisconsin 53406 Toll Free: 800.235.1638 Phone: 262.639.6770 Fax: 262.417.1155

More information

Installation Instructions

Installation Instructions 85-4341 rev. 04 10-15 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Chevy 2500/3500/4500

More information

Innoquest Item # Product Manual

Innoquest Item # Product Manual Innoquest Item # 29480 Product Manual Table of Contents 1.0 Safety Information. 2 2.0 Introduction... 3 2.1 Spray Case Diagram. 3 2.2 Features 4 3.0 Specifications. 5 4.0 Set-up & Operation... 6 4.1 Charging

More information

TOTALIZER-TRANSMITTER

TOTALIZER-TRANSMITTER TOTALIZER-TRANSMITTER MODEL TR04-2 OPERATION AND MAINTENANCE MANUAL PARTS LIST FEATURING: *SEALED HOUSING *STANDARD TOTALIZER ASSEMBLY *MAGNETICALLY ACTUATED REED SWITCH 3255 WEST STETSON AVENUE HEMET,

More information

INSTRUCTION MANUAL L WIND CONE

INSTRUCTION MANUAL L WIND CONE Cooper Industries DOCUMENT September 29, 2009 Revision B Crouse-Hinds Division Crouse-Hinds Airport Lighting Products 1200 Kennedy Road Windsor, CT 06095 860 683-4300 Fax 860 683-4354 Title: INSTRUCTION

More information

HALLMARK INDUSTRIES INC

HALLMARK INDUSTRIES INC Performance Part No. HP. CONVERTIBLE JET PUMP USER S MANUAL GPH of Water @ Total Discharge Pressure of 40 psi Max. Pressure Max suction (shallow well) Max Suction (deep well) Max GPM (@0 head) Max Discharge

More information

MODEL 900 IMPELLER-TYPE FLOW METER

MODEL 900 IMPELLER-TYPE FLOW METER MODEL 900 IMPELLER-TYPE FLOW METER - For Water Applications - INSTALLATION & INSTRUCTION MANUAL 8635 Washington Avenue Racine, Wisconsin 53406 Toll Free: 800.235.1638 Phone: 262.639.6770 Fax: 262.417.1155

More information

INSTRUCTIONS Refillable, reusable. Extra versatile. Pressurized by free air

INSTRUCTIONS Refillable, reusable. Extra versatile. Pressurized by free air SURE SHOT SPRAYERS INSTRUCTIONS Refillable, reusable. Extra versatile. Pressurized by free air MODEL M 24 OZ. DIRECTIONS FOR OPERATING MODEL M SPRAYERS 1) ALWAYS DEPRESSURIZE SPRAYER BEFORE REMOVING ANY

More information

Pressurized Pond Filter Up to 850 gallons

Pressurized Pond Filter Up to 850 gallons Pressurized Pond Filter Up to 850 gallons REMINER CALL 1-888-755-4497 EFORE RETURNING TO STORE. MOEL/MOELO #PZF850 Questions, problems, missing parts? efore returning to your retailer, call our customer

More information

IN SUMP PROTEIN SKIMMER TOP QUALITY & HIGHLY EFFICIENT INCLUDES NEEDLE WHEEL PUMP 1 YEAR WARRANTY

IN SUMP PROTEIN SKIMMER TOP QUALITY & HIGHLY EFFICIENT INCLUDES NEEDLE WHEEL PUMP 1 YEAR WARRANTY IN SUMP PROTEIN SKIMMER TOP QUALITY & HIGHLY EFFICIENT INCLUDES NEEDLE WHEEL PUMP 1 YEAR WARRANTY 1 ASSEMBLY PARTS NOTE: Make sure all connections are secure. Examine for damages before installation. Bubble

More information

CSA CERTIFIED Conforms to UL 507

CSA CERTIFIED Conforms to UL 507 Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550

More information