Replace brake pads and discs - rear * (Volkswagen Golf )
|
|
- Marilynn Nicholson
- 5 years ago
- Views:
Transcription
1 Replace brake pads and discs - rear * (Volkswagen Golf ) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're not sure - don't act! Administration will not accept any responsibility for damage to you or your vehicle after following these instructions bellow. Tools we need: Jack + stands, 17mm socket to take the wheels off, 13mm socket and 15mm spanner to take caliper off, cross head or torx screwdriver to take brake disc off, 8mm allen bit in case if you want to take caliper bracket off, get some tissues to catch any possible excessive brake fluid. Posted by: waway This is how we do it: Jack up the car, do not use jack on its own - use stands, chock front wheels, put car in the gear - safety! Remove rear wheels. *NOTE: Let brakes to cool down - do not work on them straight after driving. - Page 1 of 10 -
2 To remove brake pads: - take 2x13mm bolts out, counterhold with 15mm open end spanner (See Image 1 below) - wiggle the caliper out - use screwdriver, spanner or pry bar if necessary for leverage - do not hang the caliper on the brake line - rest it on something (use some box, or as it shown on Image 2 canister) - remove the brake pads (Image 2), if new brake pad set comes with new anti-rattle springs - remove springs as well (Image 2) To remove disc: - take little securing bolt out (Image 3), can be torx, can be cross-head - remove brake disc, tap it with the hammer, if it's stuck If for any reason you need to remove caliper bracket - it's help by 2x8mm hex-allen bolts at the back (Image 4), tightening torque - 80Nm Install new disc, lubricate little securing bolt with copper grease - so you'll be thankful to yourself, if it needs to be removed in the future. Tightening torque for securing bolt 4Nm Because new brake pads are much thicker than worn out old ones, the piston on - Page 2 of 10 -
3 caliper needs to be pushed back. On rear calipers it needs to be pushed and turned (clockwise) at the same time. Use caliper piston retraction tool (Image 5) *NOTE: While retracting piston, excessive brake fluid will go back, so keep checking level in brake fluid reservoir (under the bonnet/hood), pump out if necessary, use tissues. Avoid brake fluid getting onto paintwork or skin/eyes! Clean any dirt from caliper bracket, use metal brush. Install new anti-rattle springs, apply some copper grease for easier brake pads movement. For perfection you should clean lubricate caliper pins (See Image 6 and video below). Lubricate with heat resisting grease, such as copper or silicone grease. *NOTE: Make sure that no grease gets onto the braking surfaces! Compare that new pads are same type as the old ones, install new pads into the bracket, make sure that braking surface fully touching brake disc, peel off protective stickers at the back of new brake pads and apply some copper grease on the contact surfaces with the caliper. Put caliper back on and tighten bolts up to 35Nm (use new bolts from brake pad set). Once you finished on both wheels, before you go: - press brake pedal few times, so pistons squeeze pads to the disc - apply and release hand brake few times, adjust, if necessary - search "adjust parking brake" in manuals at our website - for the first 100 miles avoid hard braking, let new pads to rub properly to the discs. - Page 3 of 10 -
4 Happy days! Here's YouTube video link: And here is another video about lubricating pins: - Page 4 of 10 -
5 Image 1 - Caliper bolts - Page 5 of 10 -
6 Image 2 - Removing brake pads - Page 6 of 10 -
7 Image 3 - Removing securing bolt for brake disc - Page 7 of 10 -
8 Image 4 - Caliper bracket bolts - Page 8 of 10 -
9 Image 5 - Caliper piston retraction tool - Page 9 of 10 -
10 Image 6 - Clean and lubricate caliper pins - Page 10 of 10 -
Replace brake pads and discs - front * (Volkswagen Sharan 2010-Present)
Replace brake pads and discs - front * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions,
More informationReplace front brake pads and discs * (Ford Galaxy )
Replace front brake pads and discs * (Ford Galaxy 2006-2015) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're
More informationReplace clutch and flywheel * (Volkswagen Sharan 2010-Present)
Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationminimum allowable level, remove brake fluid to the midway point before proceeding.
1 of 6 12/7/2011 6:45 PM aution: Refer to Brake Dust Caution in Service Precautions. Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Removal Procedure 1. Inspect the fluid level
More informationThe following information shows the steps to change the rear brake pads and rotors on an E36 chassis.
1 of 20 1/18/2010 9:15 PM See More DIY Articles Bookmark Site! The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. Disclaimer: The following information
More information2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up.
FRONT BRAKES: 2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up. 1. Remove this bolt holding brake line bracket to the suspension. 2. I had to replace all 4 rotors at 60K miles, so
More informationFRONT BRAKE COMPONENTS
BR18 COMPONENTS BRAKE PADS REPLACEMENT HINT: If a squealing noise occurs from the brakes while driving, check the pad wear indicator plate. If the pad wear indicator plate contacts the disc, the brake
More informationHow To: Replace Brembo front discs & pads
How To: Replace Brembo front discs & pads Necessary Tools required Good quality socket set. T55 Torx/spline bit of very good quality. T30 Torx/spline bit. T27 Torx /spline bit WD40 Mallet. Punch. Brake
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationBrake Pad: Service and Repair Front PADS - BRAKE FRONT
2005 Dodge Truck RAM 3500 4WD Pickup L6-5.9L DSL Turbo VIN C Page 1 Brake Pad: Service and Repair Front PADS - BRAKE FRONT REMOVAL 1. Raise and support vehicle. 2. Remove the wheel and tire assemblies.
More informationFront brakes, servicing
Page 1 / 12 46-1 Front brakes, servicing Front brakes - brake caliper Girling, servicing Note : After replacing brake pads, depress brake pedal several times firmly to properly seat brake pads in their
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More information1 of 11 4/11/ :35 AM
1 of 11 4/11/2015 11:35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM-6007-30 Adaptor Removal Procedure 2 of 11 4/11/2015 11:35 AM Caution: Refer to Brake Dust Caution
More informationALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Hummer H2 V8-6.0L Conversion Calculator Vehicle Level Brakes
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationRemoving/installing final drive
1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm
More informationDodge Caravan Brake Pads and Rotors Replacement
2001-2007 Dodge Caravan Brake Pads and Rotors Replacement Written By: aelegg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide shows how easy it is for someone with little skills to
More informationAudi B5 A4/S4 Rear Wheel Bearing Service Kit
Audi B5 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More information1 of 9 7/19/2016 5:35 PM
1 of 9 7/19/2016 5:35 PM PADS - FRONT/REAR BRAKE - SRT8 STANDARD PROCEDURE BRAKE PAD BURNISHING CAUTION: After installing NEW brake pads, keep in mind that braking effectiveness might be somewhat reduced
More informationFord Focus Front Brake Pad Replacement
2005-2007 Ford Focus Front Brake Pad Replacement Replacing the brake pads on all 2005-2007 Focus models with rear drum brakes. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationAudi B6/B7 A4/S4 Rear Wheel Bearing Service Kit
Audi B6/B7 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationPerformance Brake Caliper Guide Bushing Set Installation Guide
Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationFord Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions
Ford Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions Time Necessary: Approximately 1.5 hours Tools Required: 15 MM Socket Ratchet PryBar Floor Lift or: o Floor Jack o (2) Jack Stands
More informationRelease the electrical wire from the bracket -2- toward the left -A- and remove.
Page 1 of 8 Front Brake Pads, FBC-60, Removing and Installing Always replace on both axles. Special tools and workshop equipment required t Torque Wrench 5 50 Nm -V.A.G 1331- t Reversible Ratchet -V.A.G.
More informationBMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li)
Page 1 of 11 BMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li) This guide will detail how to change the rear brakes on late model BMW E65 / E66 s. It was performed on a 2003
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationFront brakes, servicing (HP-2 dual-piston calipers - steel)
Page 1 of 19 46-9 Front s, servicing (HP-2 dualpiston calipers - steel) Note: Always install complete repair kit After replacing pads and before moving vehicle, depress pedal several times firmly to properly
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationAudi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions
Audi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal
More information2005 Dodge Grand Caravan
REMOVAL REMOVAL - REAR DISC BRAKE SHOES 1. Raise vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE). 2. Remove rear wheel and tire assemblies from vehicle. 3. Remove the caliper
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationRepairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor
CIS-Jetronic.com 07.3-0997-06-01 Repairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor When do you have to repair your CIS Bosch fuel distributor? If your car has rough idle, low power, high
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationThe Driveshaft Shop Aluminum One Piece Driveshaft (05-10 GT)
Install Time: 2-3 Hours Tools Needed: Metric Hex Key Set 10mm, 13mm, 15mm deep socket 12 point 12mm deep socket ⅜ Rachet 5 ½ Rachet Extensions ½ Drive Breaker Bar Blue Thread Locker Rubber Mallet Pry Bar
More informationXJ CHEROKEE LIFT KIT
921633XN200 Thank you for choosing Rough Country for your suspension needs. 84-01 4.5 XJ CHEROKEE LIFT KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationDetroit Tuned R56 Oil Service How-To
Detroit Tuned R56 Oil Service How-To Welcome to Detroit Tuned s how-to guide for an oil service for an R56 MINI Cooper. It s always best to do an oil change on a hot engine as the hot oil will drain better
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More information2003 Infiniti G35. CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out.
FRONT & REAR DISC PADS CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out. To determine which brake system vehicle is equipped with, see MODEL IDENTIFICATION. Removal
More informationInstallation Guide: Front Brake Pad
Installation Guide: Front Brake Pad Ninety percent of the brake pad changes you make during the life of your vehicle will be to the front brakes because they do 60% to 70% of the braking. On most cars,
More informationGo-ped ESR750 / ESR750EX Rear Brake Installation Instructions
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationWorkshop manual 4618 BAVP 85 SX. Product Exploded View Disassembly & Assembling. Schok absorber 4618 BAVP 85 SX
Schok absorber Introduction 2 Exploded view 3 Disassembly shock absorber 4 Disassembly piston rod 12 Assembling piston rod 23 Disassembly adaptor DU-bush 33 Assembling adaptor DU-bush 36 Disassembly tube
More information2007 Pontiac G BRAKES Disc Brakes - G6
REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between
More informationInstallation instructions, accessories. Electric engine block heater, 230V, 5 cyl diesel
Installation instructions, accessories Instruction No 30795311 Version 1.2 Part. No. 31373138 Electric engine block heater, 230V, 5 cyl diesel IMG-256423 Volvo Car Corporation Electric engine block heater,
More informationDYNATRAC PRODUCTS V5.3
DYNATRAC PRODUCTS V5.3 2000-2008 Dodge Hub Kit Stage 1 4x4, Front Axle Free Spin Conversion Kit Note: This Kit is not Approved for 2007 & up 3500 Cab and Chassis Trucks Due to a Larger U-Joint (If U-Joint
More informationVW SCIROCCO TWINTERCOOLER INSTALLATION INSTRUCTIONS
VW SCIROCCO TWINTERCOOLER INSTALLATION INSTRUCTIONS Tools needed: T25 torx driver Small flat head screwdriver 12mm & 13mm socket, with ratchet Dremel or similar with cut off disc Large Phillips screwdriver
More informationAudi B7 A4 2.oT Lightweight Flywheel. Installation Tutorial ES
Audi B7 A4 2.oT Lightweight Flywheel Installation Tutorial ES2739501 Project Preparation Safety Leave the car in neutral. Park the vehicle in a safe, well lit, level area. Open the hood and place protective
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More information1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum
BRAKE PEDAL FREE PLAY 1994 Mazda MX-5 Miata DESCRIPTION & OPERATION BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum NOTE: For information on anti-lock brake systems, see ANTI-LOCK BRAKE SYSTEM article in
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove
More informationJK 3 Install Kit Instruction Pack
JK 3 Install Kit Instruction Pack 1 Contents: Rear Sway Bar Link Instructions Spring Instructions Bumpstop Instructions Rear Track Bar Bracket Instructions Extended Brake Line Instructions Quick Disconnect
More informationFRONT BRAKE COMPONENTS
BR18 BRAKE SYSTEM FRONT BRAKE COMPONENTS REPLACEMENT OF BRAKE PADS HINT: If a squealing noise occurs from the front brakes while driving, check the pad wear indicator. If there are traces of the indicator
More informationInstallation Instructions for disc brakes
Installation Instructions for disc brakes Bedford CF 230-280, built 1974-1986, not suitable for vehicles with rear twin tyres Included 2 pcs. Wheel Hubs with Wheel Bolts, Mounted Brake Discs and Wheel
More informationPOWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires
More informationREAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
More informationJK HD Skid Plate for Rear Falcon Shocks
1 JK HD Skid Plate for Rear Falcon Shocks Kit # 36-07-01-300 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate
More information1.6 HDI or TDCI (up to 2010) Turbo and injector upgrade
1.6 HDI or TDCI (up to 2010) Turbo and injector upgrade The 1.6 90 and 110 16v engines are the same apart from the turbo charger and the injectors. The injectors both use the same body however the 110
More informationThis chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models.
KYMCO MXU 500i/700i Repair Manual Brake System 9.Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models. 1.Brake Discs... 9-3
More informationShock absorber for Automotive TTX36 P/ IL. Workshop Manual
TTX6P TTX6IL Shock absorber for Automotive TTX6 P/ IL Workshop Manual Safety precautions General Warnings Note! The shock absorber/front fork/steering damper is an important part of the vehicle and will
More informationINSTALLATION INSTRUCTIONS SPULEN BILLET SPHERICAL CATCH CAN KIT - V2 VOLKSWAGEN: MK7 GOLF, GTI & GOLF R AUDI: 8V A3
INSTALLATION INSTRUCTIONS SPULEN BILLET SPHERICAL CATCH CAN KIT - V2 VOLKSWAGEN: MK7 GOLF, GTI & GOLF R AUDI: 8V A3 7675 & 7676 7499 & 7500 VIDEO INSTRUCTIONS ARE ALSO AVAILABLE ONLINE FOR A MORE ENHANCED
More information2001 Volvo V70 XC AWD L5-2.4L Turbo VIN 58 B5244T3
2001 Volvo V70 XC AWD L5-2.4L Turbo VIN 58 B5244T3 Bushing Control Arm, Replacing Bushing control arm, replacing Special tools: 951 2050 951 2923 999 5045 999 7032 999 7033 999 7035 999 7037 999 7048 999
More informationWARNING: Only perform this installation if you are experienced, fully equipped mechanic.
DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These
More informationVolkswagen Passat Driveshaft Removal (B5 TDi)
Volkswagen Passat Driveshaft Removal (B5 TDi) About this guide This document is intended as an amateur maintenance guide to assist you with removal of the driveshaft in your VW Passat. The removal procedure
More informationSteeda Bumpsteer Kit (94-04) - Installation Instructions
Steeda Bumpsteer Kit (94-04) - Installation Instructions The below installation instructions work for the following products: Steeda Bumpsteer Kit (94-04) Please read through the instructions carefully
More informationMirrored from:
Mirrored from: http://www.wranglerforum.com/f274/install-synergy-suspension-ball-joints-write-up-147062.html 03-18-2012, 02:43 AM #1 SilverSport Supporting Member WF Supporting Member Install Synergy Suspension
More informationHawk Brake Pads ( Mustang GT/V6 Rear Pair)
Hawk Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) The below installation instructions work for the following products: Hawk HPS Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) Hawk Performance Ceramic
More informationAudi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions
Audi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal
More informationXJ CHEROKEE LIFT KIT
92169600 84-01 6.5 XJ CHEROKEE LIFT KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationSERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS
SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE
More information60 76 A Body Mopar Power Disc Conversion Installation Instructions
62-72 B & E BodyMopar 60 76 A Body Mopar Power Disc Conversion Installation Instructions Special A-Body only parts shown below (In addition to parts above for A-Body cars, part # MDC66DC & MDC46DC) Your
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationSCION tc BIG BRAKE KIT Section I - Installation Preparation
SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More informationSuper T QR20 INSTRUCTIONS GENERAL RULES
INSTRUCTIONS GENERAL RULES 1. Where specified, assemble and disassemble the shock absorption system using the MARZOCCHI special tools only. 2. On reassembling the suspension system, always use new seals.
More informationMOTOR CYCLE, GENERAL PURPOSE, HARLEY - DAVIDSON MT350 TECHNICAL DESCRIPTION OIL CHANGE
MOTOR CYCLE, GENERAL PURPOSE, HARLEY - DAVIDSON MT350 TECHNICAL DESCRIPTION OIL CHANGE This is intended as a walk through & Guide only to the Oil Change on a MT350 / Rotax 348 engine Approx Procedure Time
More informationCarry out replacement in the following order:
How to replace the rear brake disc on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Replace the brake disks on the car Nissan X-Trail T30 in complete set for each axis. Regardless
More informationPage 1 of 10 43: Transmission, automatic, B5254T2, AW50/51 AWD V70 XC (01-) / XC70 (-07), 2004, B5254T2, AW50/51 AWD, L.H.D, YV1SZ59H241147306, 147306 15/10/2011 PRINT 43: Transmission, automatic, B5254T2,
More informationDisassembly. 1 Pull off the QUIK-LOK cable from the machine.
Special Tools Require Important! Torx TX0 bit 0 0 Screwdriver Torx 0 0 0 Forcing Discs 0 Before beginning the maintenance work, perform an initial check with a high voltage test according to VDE (see chapter
More informationINSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT
INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you
More informationSelf Adjusting Disc Brakes
Disc Brakes Four advantages of Disc Brakes to Drum Brakes 1) Resistance to heat fade 2) Resistance to water fade 3) Less of a tendency to pull 4) Automatically adjust to lining wear Self Adjusting Disc
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationSouthwest Windpower Instruction Sheet AIR-X Circuit Replacement Kit
Southwest Windpower Instruction Sheet AIR-X Circuit Replacement Kit Tools Required 5 / 32 Hex key 5 / 16 Hex key 7 / 64 Hex key Standard screwdriver Pair of external snap ring pliers Rubber mallet Hammer
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationBMW 3 Series E46 Front Wheel Bearing
BMW 3 Series E46 Front Wheel Bearing Replacement A step-by-step guide on BMW 3 Series E46 Front Wheel Bearing Replacement. Written By: Danielle 2017 guides.drivediy.com Page 1 of 13 INTRODUCTION Discover
More informationPypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & GT) - Installation Instructions
Pypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & 94-97 GT) - Installation Instructions The below installation instructions work for the following products: Pypes 409 Stainless
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More information04-08 FORD F150 4 KIT
9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationTech Feature: Brake Job on Ford Edge
Tech Topics Tech Feature: Brake Job on Ford Edge By Andrew Markel email Editor, Brake & Front End Magazine August 20, 2010 The Ford Edge is an SUV based on a the CD3 platform. The brakes on these vehicles
More information