3/13/ :32 AM. NOTICE: Do not disconnect the hose.
|
|
|
- Kristopher Moody
- 5 years ago
- Views:
Transcription
1 1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install a new gasket and the drain plug after draining engine oil. Torque: 25 Nm (255 kgf-cm, 18 ft. lbs.) 7. REMOVE EXHAUST PIPE ASSEMBLY FRONT 8. REMOVE ENGINE MOVING CONTROL ROD W/ BRACKET a. Remove the 3 bolts and engine moving control rod w/ bracket. 9. REMOVE ENGINE MOUNTING STAY NO. 2 RH 10. REMOVE ENGINE MOUNTING BRACKET NO. 2 RH 11. REMOVE FAN AND GENERATOR V BELT 12. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 13. DISCONNECT ENGINE WIRE 14. REMOVE GENERATOR ASSEMBLY 15. REMOVE VANE PUMP ASSEMBLY NOTICE: Do not disconnect the hose. 16. REMOVE IGNITION COIL ASSEMBLY 17. DISCONNECT VENTILATION HOSE 18. DISCONNECT VENTILATION HOSE NO. 2
2 2 of REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY a. Remove the bolt and disconnect the engine wire harness clamp. b. Remove the 8 bolts and 2 nuts, and disconnect the cylinder head cover. 20. SET NO. 1 CYLINDER TO TDC/COMPRESSION 21. REMOVE CRANKSHAFT PULLEY a. Remove the crankshaft pulley (TMC made). 1) Using SST, loosen the pulley bolt. SST ( ),
3 3 of 25 2) Using SST, remove the crankshaft pulley. SST ( , , , ) b. Remove the crankshaft pulley (TMMK made). 1) Using SST, loosen the pulley bolt. SST ( , ) 2) Using SST, remove the crankshaft pulley.
4 4 of 25 SST ( , , , , , , ) 22. REMOVE CRANK POSITION SENSOR 23. REMOVE OIL PAN SUB-ASSEMBLY a. Remove the 12 bolts and 2 nuts. b. Insert the blade of SST between the crankcase and oil pan, cut off applied sealer and remove the oil pan. SST NOTICE: Be careful not to damage the contact surface of the cylinder block and oil pan.
5 5 of REMOVE CHAIN TENSIONER ASSEMBLY NO. 1 a. Remove the 2 nuts, timing chain tensioner and gasket. NOTICE: Be sure not to revolve the crankshaft without the chain tensioner. 25. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY a. Remove the bolt, the bolt and drive belt tensioner.
6 6 of INSTALL ENGINE HANGER NO. 1 a. Install the engine hanger No. 1, No. 2 and bolt as shown in the illustration. Torque: 38 Nm (387 kgf-cm, 30 ft. lbs.) Parts No.: Engine hanger No Engine hanger No Bolt REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR a. Attach the engine chain hoist to the engine hangers. CAUTION: Do not attempt to hang the engine by hooking the chain to any other part. b. Remove the bolt, and disconnect the engine mounting insulator. c. Remove the bolt and disconnect the engine lateral control rod (M/T).
7 7 of 25 d. Remove the bolt and disconnect the steering gear return hose clamp from the frame. e. Remove the 4 nuts from the engine mounting insulator RH. f. Raise the engine and remove the engine mounting insulator RH.
8 8 of REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET a. Remove the 3 bolts and the engine mounting bracket RH. 29. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY a. Remove the stud bolt for drive belt tensioner from the cylinder block. b. Remove the 14 bolts and 2 nuts. c. Remove the timing chain cover with a screwdriver.
9 9 of 25 NOTICE: Be careful not to damage the contact surfaces of timing chain cover, cylinder block and cylinder head. 30. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO REMOVE CHAIN TENSIONER SLIPPER 32. REMOVE CHAIN VIBRATION DAMPER NO REMOVE CHAIN SUB-ASSEMBLY 34. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET 35. REMOVE NO. 2 CHAIN SUB-ASSEMBLY a. Turn the crankshaft counterclockwise 90, and align an adjusting hole of the oil pump drive shaft gear with the groove of the oil pump. b. Put a bar ([diameter] 4 mm) in the adjusting hole of the oil pump drive shaft gear to lock in position, and remove a nut.
10 10 of 25 c. Remove the bolt, chain tensioner plate and spring. d. Remove the chain tensioner, oil pump drive shaft gear and No. 2 chain. 36. INSTALL NO. 2 CHAIN SUB-ASSEMBLY a. Set the crankshaft key into the left horizontal position. b. Turn the cutout of the drive shaft to the top.
11 11 of 25 c. Align the mark links (yellow colored links) with the timing marks of the gear as shown in the illustration. d. Insert the gears with chain to the crankshaft and oil pump shaft. e. Temporarily tighten the oil pump drive shaft gear by a nut. f. Inset the damper spring into the adjusting hole, and install the chain tensioner plate by a nut. Torque: 12 Nm (122 kgf-cm, 9 ft. lbs.)
![Put a bar ([diameter] 4 mm) in the adjusting hole of the oil pump drive shaft gear to lock in position, and assemble a nut.](/docs-images/85/92232946/images/12-1.jpg "Torque: 30 Nm (301 kgf-cm, 22 ft. lbs.) i. Rotate the crankshaft clockwise 90, and align the crankshaft key to the top. 37.")
12 12 of 25 g. Align an adjusting hole of the oil pump drive shaft gear with the groove of the oil pump. h. Put a bar ([diameter] 4 mm) in the adjusting hole of the oil pump drive shaft gear to lock in position, and assemble a nut. Torque: 30 Nm (301 kgf-cm, 22 ft. lbs.) i. Rotate the crankshaft clockwise 90, and align the crankshaft key to the top. 37. INSTALL CHAIN VIBRATION DAMPER NO. 1 Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) 38. INSTALL CHAIN SUB-ASSEMBLY a. Set No. 1 cylinder to TDC/compression.
13 13 of 25 1) Align the timing marks of the camshaft timing sprockets with No. 1 bearing caps. 2) Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
14 14 of 25 b. Align the mark link (gold or orange colored link) with the timing mark of the crankshaft timing gear. c. Using a SST, install the sprocket. SST d. Align the mark links (gold or yellow colored links) with the timing marks of the camshaft timing gear, and install the chain.
15 15 of INSTALL CHAIN TENSIONER SLIPPER Torque: 19 Nm (194 kgf-cm, 14 ft. lbs.) 40. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO. 1 a. Install the crankshaft position sensor plate the "F" mark facing forward. 41. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY NOTICE: - Remove any oil from the contact surface. - Install the chain cover within 3 minutes after applying seal packing. - Do not start the engine 2 hours after installing. a. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
16 16 of 25 b. Apply seal packing in the shape of bead (Diameter 2 mm (0.099 inch)) as shown in the illustration. Seal packing: Part No or equivalent
17 17 of 25 c. Apply seal packing in the shape of bead (Diameter 3-4 mm ( inch)) as shown in the illustration. Seal packing: Part No or equivalent d. Install the timing chain cover with the 14 bolts and 2 nuts. Torque:
18 18 of 25 Bolt A 9.0 Nm (92 kgf-cm, 80 inch lbs.) Bolt B 21 Nm (214 kgf-cm, 15 ft. lbs.) Bolt C 43 Nm (438 kgf-cm, 32 ft. lbs.) Nut 9.0 Nm (92 kgf-cm, 80 inch lbs.) e. Install the stud bolt to the drive belt tensioner. Torque: 10 Nm (102 kgf-cm, 7 ft. lbs.) 42. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY a. Install the drive belt tensioner with the bolt and nut. Torque: 59.5 Nm (607 kgf-cm, 44 ft. lbs.) 43. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET a. Install the engine mounting bracket RH with the 3 bolts. Torque: 54 Nm (551 kgf-cm, 40 ft. lbs.) 44. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR a. Raise the engine and install the engine mounting insulator RH.
19 19 of 25 b. Install the engine mounting insulator RH with the 4 nuts. Torque: Bolt A 95 Nm (969 kgf-cm, 70 ft. lbs.) Bolt B 87 Nm (888 kgf-cm, 64 ft. lbs.) c. Install the bolt and disconnect the steering gear return hose clamp from the frame. Torque: 8.0 Nm (80 kgf-cm, 69 inch lbs.)
20 20 of 25 d. Install the engine mounting insulator FR with the bolt. Torque: 87 Nm (888 kgf-cm, 64 inch lbs.) e. Install the engine lateral control rod with the bolt (M/T). Torque: 89 Nm (910 kgf-cm, 69 inch lbs.) 45. INSTALL OIL PAN SUB-ASSEMBLY NOTICE: - Remove any oil from the contact surface.
21 21 of 25 - Install the oil pan within 3 minutes after applying seal packing. - Do not start the engine 2 hours after installing. a. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surface of the cylinder block and oil pan. b. Apply seal packing in the shape of bead (Diameter 3-4 mm (0.157 inch)) as shown in the illustration, and install the oil pan. Seal packing: Part No or equivalent
22 22 of 25 c. Install the oil pan with the 12 bolts and 2 nuts. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) 46. INSTALL CHAIN TENSIONER ASSEMBLY NO INSTALL CRANK POSITION SENSOR a. Install the bolt and crankshaft position sensor. Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) b. Confirm the wire harness of the crank position sensor is placed as shown in the illustration.
23 23 of INSTALL CRANKSHAFT PULLEY a. Install the crankshaft pulley (TMC made). 1) Align the pulley set key with the key groove of the pulley, and side on the pulley. SST ( ), ) Using SST, install the pulley bolt. Torque: 170 Nm (1,733 kgf-cm, 125 ft. lbs.) b. Install the crankshaft pulley (TMMK made). 1) Align the pulley set key with the key groove of the pulley, and side on the pulley. SST ( , ) 2) Using SST, install the pulley bolt. Torque: 170 Nm (1,733 kgf-cm, 125 ft. lbs.)
24 24 of 25 c. Turn the crankshaft counterclockwise, and disconnect the plunger knock pin from the hook. d. Turn the crankshaft clockwise, and check that the slipper is pushed by the plunger. 49. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY 50. INSTALL IGNITION COIL ASSEMBLY Torque: 9.0 Nm (92 kgf-cm, 80 inch lbs.) 51. INSTALL VANE PUMP ASSEMBLY 52. INSTALL GENERATOR ASSEMBLY 53. INSTALL ENGINE WIRE Torque: 52 Nm (531 kgf-cm, 38 ft. lbs.) 56. INSTALL ENGINE MOUNTING STAY NO. 2 RH Torque: 64 Nm (653 kgf-cm, 47 ft. lbs.) 54. INSTALL FAN AND GENERATOR V BELT 55. INSTALL ENGINE MOUNTING BRACKET NO. 2 RH
25 25 of INSTALL ENGINE MOVING CONTROL ROD W/ BRACKET a. Install the engine mounting control rod w/ bracket with 3 bolts. Torque: 64 Nm (653 kgf-cm, 47 ft. lbs.) 58. INSTALL EXHAUST PIPE ASSEMBLY FRONT 59. INSTALL FRONT WHEEL RH Torque: 103 Nm (1,050 kgf-cm, 76 ft. lbs.) 60. INSTALL HOOD SUB-ASSEMBLY Torque: 13 Nm (133 kgf-cm, 10 ft. lbs.) 61. ADD ENGINE OIL 62. INSPECT OIL LEAK 2014 ALLDATA, LLC. All Rights Reserved. (Version )
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
VALVE CLEARANCE (3ZZ FE/4ZZ FE)
ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
TIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
VALVE CLEARANCE (1ZZ FE)
ENGINE MECHNICL DJUSTMENT 145 140OE02 1. REMOVE CYLINDER HED COVER NO.2 (a) Remove the 2 nuts, 2 clips and cylinder head cover. 65077 2. DISCONNECT ENGINE WIRE (a) Remove the 5 clamps from the 5 clamp
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL
25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.
CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE
REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.
ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) 2002 Timing Chain: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4 WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS
REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.
1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR
3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]
![3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]](/thumbs/93/113245190.jpg "3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]")
1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove
2001 Toyota MR ENGINES' '1.8L 4-Cylinder
TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
Technical Service BULLETIN
Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may
12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.
TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.
OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.
1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket
REPLACEMENT 1. REMOVE ENGINE UNDER COVER RH. 2. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 2 screw, 3 clips and engine under cover.
14100 ENGINE MECHNICL REPLCEMENT 1. REMOVE ENGINE UNDER COVER RH 140OJ02 2. REMOVE CYLINDER HED COVER NO.2 (a) Remove the 2 screw, 3 clips and engine under cover. 65077 3. REMOVE FN ND GENERTOR V BELT
TIMING BELT (5S FE) COMPONENTS
ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds
8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal
1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley
ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)
ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align
Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987
Timing Chain: Service and Repair Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 PREPARATION FOR REMOVAL OF TIMING CHAIN 1. REMOVE CYLINDER HEAD 2. REMOVE RADIATOR 3. REMOVE OIL PAN (a) Remove the engine
2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
PARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
VALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
TIMING BELT (1MZ FE Jan., 2003)
14 100 TIMING BELT (1MZ FE Jan., 2003) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM972U on page
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002
Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR
CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)
144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1
2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
1ZZ-FE ENGINE MECHANICAL ENGINE UNIT DISASSEMBLY. If you paid for the content in this manual you were screwed!
1ZZ-FE ENGINE MECHANICAL ENGINE UNIT 107 DISASSBLY 1. ROVE OIL FILLER CAP SUB-ASSBLY (a) Remove the oil filler cap from the cylinder head cover. A064852 A065656 A064854 2. ROVE OIL FILLER CAP GASKET (a)
LUBRICATION SYSTEM (April, 2003)
SYSTEM (April, 2003) SYSTEM (April, 2003) ONVEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the L and
3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure
2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation.
4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)
![4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)](/thumbs/96/128786582.jpg "4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)")
TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT
EM20 REMOVAL EM11901 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY 5. REMOVE NO.2 CYLINDER HEAD COVER 6. REMOVE IGNITION COILS (See
INSTALLATION. Check that the idler pulley moves smoothly.
ENGINE MECHANICAL (5SFE) INSTALLATION EM23 EM08604 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000,
TIMING BELT REMOVAL/INSTALLATION [ZM]
![TIMING BELT REMOVAL/INSTALLATION [ZM]](/thumbs/93/113759411.jpg "TIMING BELT REMOVAL/INSTALLATION [ZM]")
ALLDATA Online - 2000 Mazda Protege LX L4-6L DOHC - Service an... 1 of 8 6/26/2012 7:53 PM TIMING BELT REMOVAL/INSTALLATION [ZM] 5. 6. 7. 8. 9. Disconnect the negative battery cable. Remove the CMP sensor.
INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.
8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:
EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY
REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side
112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure
PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley.
EM26 INSTALLATION EM11B01 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000, 0996300600) Torque:
2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing
2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for installation.
CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U)
Inward Sensor A05060 INSTALLATION EM21 EM0ZD02 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley, and slide on the timing pulley. (b) Install the
1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina
EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE
ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY
2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
Mazda3 - Workshop Manual - Engine
Page 1 of 18 2005 - Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks
EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION
EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should
Toyota Yaris L4-1.5L (1NZ-FE) 2008
Toyota Yaris L4-1.5L (1NZ-FE) 2008 Timing Chain: Service and Repair Components 1 NZ-FE ENGINE MECHANICAL: TIMING CHAIN : COMPONENTS Timing Chain: Service and Repair Removal 1 NZ-FE ENGINE MECHANICAL:
2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for 10) Install
OIL PUMP (for 4WD and Pre-Runner)
1GR-FE BRICATION OIL PUMP (for 4WD and Pre-Runner) OIL PUMP (for 4WD and Pre-Runner) ENGINE 1GR-FE BRICATION COMPONENTS 23 88 (897, 65) 88 (897, 65) NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY FRONT PROPELLER
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
INSTALLATION. Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
M20 Timing Mark NGIN MHNIL INSTLLTION M19G01 1. INSTLL MSHFT TIMING SPROKT ND VVT TIMING SPROKT (a) lign the camshaft knock pin with the knock pin groove on the sprocket side with the timing mark, and
REMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section.
303-01B-1 303-01B-1 REMOVAL Cylinder Head Material Item Specification Special Tool(s) Motorcraft Metal Surface Prep Modular Engine Lift Bracket ZC-31 303-F047 (014-00073) or equivalent Silicone Gasket
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL
92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the
6/6/2018 2ZR-FXE Engine Mechanical: Camshaft: Removal 2012 Toyota Prius V MotoLogic
2012 Prius V REMOVAL REMOVE ENGINE ASSEMBLY WITH TRANSAXLE Report a problem with this article More Info INSTALL ENGINE STANDMore Info REMOVE ENGINE HANGERMore Info REMOVE THROTTLE BODY ASSEMBLYMore Info
Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
TIMING BELT COMPONENTS
EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
SECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
TIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
TIMING BELT (3S FE) COMPONENTS
Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
Page 1 of 11 Assembly 50. Install the timing chain guide. Tighten to 12 Nm. Page 2 of 11 51. Install the crankshaft sprocket. 52. Install the chain tensioning tool 303-532 to the exhaust camshaft sprocket.
2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
IN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer