Thank You! For purchasing our eflux Flow pump. Please read all instructions before getting in the LOOP!

Transcription

1 eflux DC Table of Contents Safety Instructions & Warnings What s Included & Installation eflux DC Installation Warranty & Safety Warnings 5 Thank You! For purchasing our eflux Flow pump. Please read all instructions before getting in the LOOP! Safety Instructions & Warnings IMPORTANT: Please refer to additional safety warnings on last page. - Keep out of reach children. Do not allow children to play with pump, pump Manifold or power supply. - Never run flow pump dry or out of water, do NOT run dry. - Do not submerse more than.5m/4 ft. of water depth. - Always unplug with dry hands for any maintenance or service. - eflux flow pumps are. Ensure one UL transformer is used per wave pump. - Ensure UL transformer is plugged into a GFCI approved outlet with a drip loop. - Do not exceed maximum head pressure or height specification. - ALWAYS follow sump and tank/overflow manufacturer instructions regarding check valves - Turn controller OFF and disconnect pump from power before performing any service. - Ensure eflux flow pumps and any accessories all have a drip loop installed before plugging into the flow pump manifold HUB as shown below. - Only use in freshwater or saltwater applications, do not use pumps in other liquids. om Use only with GFCI Protected AC Outlet DC Ensure correct voltage power supply for each component Power Supply AC Power Ensure use of drip loop for all cables eflux DC SAVE THESE INSTRUCTIONS Page

2 What s Included Installation Instructions C Each eflux DC Flow pump includes: Item Description Quantity A eflux DC B Rubber Pump Mounts (pre-installed) C 4V DC Transformer, UL Listed D w/microusb Cable E Bracket & Mounting Hardware F Pump Screen Inlet G Inlet/Outlet Fittings F G D A E Installation - READ SAFETY WARNINGS BEFORE INSTALLATION Important - Please visit our website for installation videos at B ft. Pump Specifications Max. Max. Max. Item# gph Height Watts Voltage Outlet ft./.m 0 /4" & ft./4.5m 55 /4" & " ft./6m 80 /4" & " *Note: threaded PVC fittings are not recommended, but are compatible on some pumps. If using PVC fittings do not overtighten and ensure teflon tape is used. Head Pressure 8 ft. 5 ft. ft. 9 ft. 6 ft. ft. Model 600 Max Watts: 55 Model 6009 Max Watts: 0 Model 60 Max Watts: gph 500 gph 000 gph 500 gph 000 gph 000 gph 89 lph 785 lph 5670 lph 7570 lph 946 lph,56 lph Flow Rate Plumbing the eflux DC Flow pump The eflux DC flow pump can be installed either submersible (internal) or inline (external). If using in a submersible application, please use the inlet pump screen (included). Submersible External Inline Page

3 Installation eflux DC NOTE: Please ensure to follow your aquarium tank and sump/filter manufacturer instructions regarding the minimum size requirement of your sump and if a check valve is required. Installing Pump Submersible (internal) Installation Step. Thread pump filter screen to inlet of the pump. Step. Place 0-ring inside the outlet barb fitting and quick coupling. Thread barb fitting to pump and hand tighten. Step. Connect return hose (not included) by sliding over barb fitting. Ensure hose is secured using a hose clamp (not included). Step 4. Fill sump with water and check for water/air leaks. Inline (external) Installation Step. Place o-ring inside the inlet barb fitting and quick coupling. Thread barb fitting to pump inlet and hand tighten. Step. Place o-ring inside the outlet barb fitting and quick coupling. Thread barb fitting to pump outlet and hand tighten. Step. Connect inlet hose (not included) by sliding over inlet barb fitting. Ensure hose is secured by using a hose clamp (not included.) Connect return hose to outlet barb fitting and secure with clamp. Step 4. Fill sump with water and check for water/air leaks. Installing Step. Choose a location underneath your aquarium cabinet free of excessive moisture and/or saltwater. If connecting to another manifold HUB, ensure distance between HUBs is -4. Step. Using included wood mounting screws, mount the eflux flow pump HUB mounting bracket to stand. Slide flow pump manifold HUB into bracket. Wood Screws Manifold HUB Mounting Bracket Store Cap Remove Cap Store Cap Note: Remove and store the silicone caps on the manifold HUB mounting bracket. Keep caps in place when not using other ports for protection. Page

4 Installation Pump Power DC Input Pump Connection Pump Dial Flow Control Step. Plug power supply into DC input on manifold HUB. Installation Instructions Important: Before connecting all of the components together, please review the following specifications in regards to the and appropriate connections. Communication LED Indicator Lights E Specifications: Pump DC Inputs: Voltage: Max. DC Input per Channel: 0w@ Max. DC Output per Channel: 80w@ P Indicator LEDs: D C A (Blue)= Indicates 050 gph pump is connected B B (Blue)= Indicates 900 gph pump is connected Port# A C (Blue)= Indicates 70 gph pump is connected Port# D (Blue)= Feed - flashes when pump is in feed mode Port#4 Port# E (Red)= Active feedback/pump status: MicroUSB Ports (all for communication) Red Solid - indicates pump is operating normal Red Flashing - indicates non-normal operation Connecting Pump to (pump running dry, over voltage over/under voltage, over temperature) Step. Plug DC pump cable into pump connection on manifold HUB. Step. Red LED status light should turn solid red. Adjust flow from 0-00% using dial until flow rate is acheived. NOTE: eflux DC pumps have a slow ramp to speed, allow pump to run for 0-5 seconds for pump to reach adjusted flow. AC Power Transformer Connect to DC Input Connect to Pump Input P P P To other LOOP S Note: FEED mode will only operate when DC pump is plugged into a manifold HUB with an Orbit IC controller, eflux wave pump controller or the HUB is controlled via Bluetooth. When in FEED mode, DC flow pump will ramp down to 0% flow for 0 minutes, then ramp to normal speed. Pump Maintenance **Important - Due to harsh conditions found around marine aquariums, it is important to perform the following pump maintenance every 6 months. When performing any maintenance or service, ensure pump is disconnected from power and manifold HUB.. Remove pump from service by disconnecting power and removing pump from sump via disconnect fittings.. Carefully remove front pump cover, o-rings and slide impeller from pump. Use a small soft brush and running freshwater to clean any organic debris. If any calcium deposits have developed, soak the components in mild vinegar/freshwater solution. DO NOT use strong acids.. Re-assemble pump, reconnect fittings with all o-rings properly in place and reconnect power. Page 4

5 Warranty Information Safety Warnings and Warranty P P P Drip Loop Drip Loop Current-USA One Year Limited Warranty This product MUST be purchased from an authorized Current-USA reseller. Visit our website for a list of unauthorized resellers. Current USA, Inc. warrants this product against defects in materials and worksmanship for ONE () YEAR from the date of original retail purchase and is not transferable. lights. Do not install pumps where strong currents can harm animals. Do not install close to sand bed where it can suck/stir sand. Pumps can produce powerful wave action in both wave and surge modes. Ensure your aquarium is designed for wave pumps and ensure pumps are mounted low enough not to push water out of the aquarium tank. Magnet assembly is VERY powerful. Be cautious not to cause injury to fingers. Keep magnets and all accessories out of reach of children. Never place magnets or pump near sensitive electronics, sharp objects or other attractive surfaces. Do not run pumps dry or out of water. Always place spacer between magnets when not in use. Always unplug with dry hands for maintenance or servicing. Turn all controllers OFF and disconnect power supply before performing any service or maintenance. This product MUST be powered by a UL or ETL listed power supply. To avoid possible electric shock, power supply MUST be plugged into a GFCI wall outlet installed by a certified electrician in accordance with all local codes. All products must have a drip loop. Page 5 DC