Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of Ford Mustang 4.7L Eng VIN A Base Service Manual: 221", 260", 289" V8 ENGINES Print Date: ENGINE NOTES COOLANT LOSS OR WATER PUMP & FRONT COVER CORROSION CORRECTION: May be caused by erosion or corrosion of aluminum water pump and front cover. To correct, replace pump and front cover with a cast iron pump and cover. When installing cast iron front cover, be sure oil fill inlet passage on front face of cylinder block is plugged and new left hand valve rocker cover with oil fill pipe is installed. NOTE: Plug inlet passage with 3/4" expansion plug (increase diameter.010" with ball peen hammer), plug must be coated with oil resistant sealer and must be installed.005" below surface. See illustration. Fig 1: Oil Filler Inlet Passage Plug Installation Courtesy of FORD MOTOR CO OIL & VACUUM LEAK AT INTAKE MANIFOLD & END SEALS CORRECTION: To correct oil and vacuum leaks, install new type cork Neoprene impregnated manifold gaskets and seals. This gasket has changed contours, port openings and thickness. Follow standard installation procedure and be sure to torque to ft. lbs ENGINE KNOCK CORRECTION: May be caused by excessive camshaft endplay. To correct, install camshaft thrust plate to reduce endplay to ". CAUTION: Two types of thrust plates are used.

2 Page 2 of 7 One is for use with nylon camshaft sprockets, and the other is for use with cast iron sprockets. DO NOT interchange these thrust plates. Thrust plates used with cast iron sprockets must be installed with oil grooves facing forward to provide correct lubrication ENGINE OVERHEATING CORRECTION: May be caused by coolant loss through distorted radiator filler neck cam lock flange. To correct, straighten cam lock flange with pliers to vertical position " ENGINE DELAYED OIL PRESSURE BUILDUP CORRECTION: If the oil pressure does not raise to normal or if the oil pressure indicator light does not go out in a reasonable length of time (approximately 5 seconds), it may be caused by a leaky oil filter anti-drain back valve, allowing the oil to drain back out of the filter after engine shut-down. NOTE: A bearing knock may also be noticed with the delayed pressure build-up. To correct, remove and discard the oil filter assembly, then remove filter insert from cylinder block. Apply a coating of oil resistant sealer on the insert-to-engine sealing surface. Reinstall oil filter insert and tighten to 85 ft. lbs. Install new service oil filter assembly " ENGINES ROCKER ARM & PUSHROD NOISE CORRECTION: May be caused by insufficient oil flow (obstructed oil passage) in pushrod, or a defective oil metering valve in hydraulic lifter. To correct, be sure oil flow through pushrod is not obstructed (with engine running wipe rocker arm weep hole). If oil flow is questionable and rocker arm is not at fault, remove hydraulic lifter. NOTE: If tappets have single groove.300" from top and have pushrod seat as shown in illustration, ALL tappets must be replaced.

3 Page 3 of 7 Fig 2: Replace This Type Tappet (See Correction Above) Courtesy of FORD MOTOR CO ENGINE REMOVAL CAUTION: Before raising or moving any engine equipped with an accelerator linkage stabilizer rod, rod should be disconnected " ENGINE CAMSHAFT NOISE CORRECTION: Excessive camshaft endplay can cause a knocking noise at low engine RPM. Correct by installing oversize camshaft thrust plate to reduce endplay to.001"-.003". Thrust plates used with nylon sprockets have oil grooves on both sides. Plate used with cast iron sprockets have grooves on one side only. Install with grooves facing forward " ENGINE CAMSHAFT ENDPLAY CHECKING CAUTION: Sprocket may break if camshaft is pried back and forth to check endplay. Back off rocker arm adjusting nuts to relieve pressure so that camshaft can be moved by hand.

4 Page 4 of " ENGINE ROCKER ARM ASSEMBLY CAUTION: Whenever individually mounted rocker arms are assembled, the valve stem tip, fulcrum seat area, and pushrod socket should be lubricated with lubriplate or equivalent. PISTONS, PINS, RINGS PISTONS PINS RINGS Engine Clearance Piston Fit Rod Fit Ring End Gap Side Clearance 221" " " " " (3) (4) " " " " (3) (4) 260" " " " " (3) (4) " " " " (3) (4) " " " " (3) (4) (7) " " (7) " 289" " (6) " " " (3) (4) " " " (8) " " " (3) (4) (7) " " (7)

5 Page 5 of " , 225 HP " " " " (3) (4) " 271 HP " " " " () (4) " , 225 HP " " " " (3) (4) (3) (3) (4) (6) (7) (8) " Snug 271, 195 HP " " " " (4) (3) " Snug Measured 1/4" from bottom of skirt. Wear Limit.006". Wear Limit.0008". Press Fit. See "Piston Pin Replacement " below. Side sealing type ring. 2-Bbl. engine. For 4-Bbl. engine " o" on Mustang. 2-Bbl. engines. On 4-Bbl. engines ". (3) (3) ENGINE NOTES > HYDRAULIC LIFTER OPERATING RANGE ADJUSTMENT 1. With No. 1 and then No. 6 pistons at TDC of compression stroke, adjust valves indicated in Steps 2 & 3 below as follows: Loosen rocker arm stud nut until there is clearance at pushrod, then tighten nut until all pushrod-to-rocker arm clearance is just removed. Then tighten stud nut an additional 3/4 turn (Supersedes previous setting of 1 1/2 turns) to place hydraulic lifter plunger in center of its travel.

6 Page 6 of 7 NOTE: Clearance between valve stem tip and rocker arm with lifter fully collapsed should be ". 2. With No. 1 piston at TDC of compression stroke, adjust the following valves: No. 1 Intake No. 4 Exhaust No. 1 Exhaust No. 5 Exhaust No. 2 Exhaust No. 7 Intake No. 3 Intake No. 8 Intake 3. With No. 6 piston at TDC of compression stroke, adjust the following valves: No. 2 Intake No. 6 Intake No. 3 Exhaust No. 6 Exhaust No. 4 intake No. 7 Exhaust No. 5 Intake No. 8 Exhaust VALVE TAPPET CLEARANCE 221" Zero Lash 260" Zero Lash 289" Bbl. Zero Lash

7 Page 7 of 7 4-Bbl., Cold.024" Int. & Exh. Hot.021" Int. & Exh Bbl. & 4-Bbl. Std. Zero Lash 4-Bbl. 271 HP Cold.022" Int. & Exh. Hot.018" int. & Exh. With hydraulic lifter fully collapsed, clearance at valve stem tip should be ". After 30 minutes operation at 1200 RPM. ENGINE NOTES > MECHANICAL LIFTER INITIAL ADJUSTMENT AFTER OVERHAUL (289" Engine) Tappet Clearance (Cold) listed in table below. For hot clearance (after engine operated for 30 minutes at 1200 RPM) see Tune-Up Data. 1. Place No. 1 piston at TDC of compression stroke. Adjust following valve clearances: No. 1, 7, 8 Intake; No. 1, 4, 5 Exhaust. 2. Turn crankshaft 1/2-turn or 180 (No. 4 piston at TDC). Adjust following valve clearances: No. 4 & 5 Intake; No. 2 & 6 Exhaust. 3. Turn crankshaft 3/4-turn or 270 from second position above (No. 3 piston at TDG) and adjust following valve clearances: No. 2, 3, 6 Intake; No. 3, 7, 8 Exhaust. Valve Tappet Clearance (Cold) 289" Engine (1963).024" Int. & Exh. ( ).022" Int. & Exh. ROCKER ARM ADJUSTING SCREW NOTE - if torque required to turn self-locking adjusting screw is less than 3 ft. lbs., install new standard or.0023" oversize screw, If minimum 7 ft, lbs. torque cannot be obtained with oversize adjusting screw, replace rocker arm and adjusting screw assembly.

FORD V8 ENGINES 209. the treated area, the block is cracked and should be replaced.

FORD V8 ENGINES 209. the treated area, the block is cracked and should be replaced. FORD V8 ENGINES 209 Cylinder block Core plug Strike here with hammer Drift 8 the treated area, the block is cracked and should be replaced. 3. Check flatness of the cylinder block deck. Place an accurate

More information

Modern Auto Tech Study Guide Chapters 13 & 14 Pages Engine Construction 52 Points

Modern Auto Tech Study Guide Chapters 13 & 14 Pages Engine Construction 52 Points Modern Auto Tech Study Guide Chapters 13 & 14 Pages 182-216 Engine Construction 52 Points Automotive Service 1. The engine top end includes the cylinder, valve cover and intake & exhaust. Head, Manifolds

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How 1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS PERFORMER RPM CAMSHAFT / LIFTERS / LUBE KIT For 343-401 c.i.d. AMC V8 Engines CATALOG # 7132 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most

More information

Valve Rocker Arm and Push Rod Installation (6.2L LS3)

Valve Rocker Arm and Push Rod Installation (6.2L LS3) 9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence

More information

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS 5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE

More information

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ] Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS Please study these instructions carefully before you remove your stock camshaft.

More information

1989 BMW 635CSi. 3.5L 6-CYL Engine - 3.5L 6-Cylinder

1989 BMW 635CSi. 3.5L 6-CYL Engine - 3.5L 6-Cylinder Fig. 3: Rocker Arm Assembly Courtesy of BMW OF NORTH AMERICA, INC. VALVE SPRINGS NOTE: Install springs with paint stripe (tight coil end) against head. Inspection Check spring free length. Check spring

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 CATALOG #2172 INSTALLATION INSTRUCTIONS

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 CATALOG #2172 INSTALLATION INSTRUCTIONS PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new camshaft. If you have any questions

More information

ENGINE MECHANICAL SPECIFICATIONS

ENGINE MECHANICAL SPECIFICATIONS GENERAL DESCRIPTION The 1955 Cadillac engine is of the V-8,overhead valve design, with a 3-13/16" bore and a 3-5/8" stroke to provide a piston displacement of 331 cubic inches. The compression ratio is

More information

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through

More information

1.6L 4-CYL - VIN [E]

1.6L 4-CYL - VIN [E] 1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L >

ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > Print 2003 Subaru Forester 2.5L Eng X ENGINE CONTROLS - ON-VEHICLE ADJUSTMENTS ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > 1. Set the vehicle onto the lift. 2. Lift-up the vehicle. 3. Remove

More information

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117 Page 1 PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 283-400 c.i.d. Chevrolet V8 Engines GENERAL INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7122 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines)

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7122 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 289-302 c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PLEASE study these instructions carefully before installing your new camshaft.

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection

More information

630, 631 & 632 Bobcat & Melroe Bobcat

630, 631 & 632 Bobcat & Melroe Bobcat Bobcat 630, 631 & 632 Bobcat & Melroe Bobcat THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF BOBCAT OR IT S SUCCESSORS. BOBCAT AND IT S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

CYLINDER HEAD OVERHAUL

CYLINDER HEAD OVERHAUL ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION -2011 Mercedes-... Page 1 of 20 CYLINDER HEAD OVERHAUL * PLEASE READ THIS FIRST * Examples used in this article are general in nature and do not necessarily

More information

CH. 48 ENGINE MECHANICAL PROBLEMS TEST

CH. 48 ENGINE MECHANICAL PROBLEMS TEST TERRY FOX AUTOMOTIVE CH. 48 ENGINE MECHANICAL PROBLEMS TEST WHEN YOU ARE DONE THIS TEST GUESS WHAT YOU THINK YOU WILL RECEIVE FOR A MARK BELOW. IF YOU ARE WITHIN 2 MARKS YOU WILL RECEIVE 2 BONUS MARKS.

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. 144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7112 MODEL: c.i.d. Oldsmobile V8, 1967 & later

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7112 MODEL: c.i.d. Oldsmobile V8, 1967 & later PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 330-350-403 c.i.d. Oldsmobile V8, 1967 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or

More information

2007 Ford Freestyle SEL

2007 Ford Freestyle SEL Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold

More information

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and

More information

Performer-Plus Camshaft/Lifters/Lube Kit Part #2182 For 351-Windsor Ford V8 Engines Installation Instructions

Performer-Plus Camshaft/Lifters/Lube Kit Part #2182 For 351-Windsor Ford V8 Engines Installation Instructions Performer-Plus Camshaft/Lifters/Lube Kit For 351-Windsor Ford V8 Engines Installation Instructions PLEASE study these instructions carefully before installing your new camshaft. If you have any questions

More information

TORKER-PLUS Camshaft/Lifters/Lube Kit Part #5022 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines)

TORKER-PLUS Camshaft/Lifters/Lube Kit Part #5022 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) TORKER-PLUS Camshaft/Lifters/Lube Kit MODEL: 289-302 c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PLEASE study these instructions carefully before installing your new camshaft.

More information

Installation Instructions

Installation Instructions CHEVROLET ENGINE SYSTEM, NON-EMISSION 1967-1987 SMALL BLOCK CHEVROLET Part Number 300-502 CHEVROLET ENGINE SYSTEM, NON-EMISSION 1962-1987 CHEVROLET 302, 327, 350 C.I.D. ENGINES Part Number 300-503-1 Installation

More information

Water Pump Replacement (L4)

Water Pump Replacement (L4) 2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure

More information

GenX Street/Strip Cylinder Heads for the GM LT1

GenX Street/Strip Cylinder Heads for the GM LT1 GenX Street/Strip Cylinder Heads for the GM LT1 Thank you for purchasing Trick Flow GenX Street/Strip aluminum cylinder heads for the GM LT1. Please follow the steps outlined in this instruction manual

More information

Remove Air Cleaner Cover and. Filter

Remove Air Cleaner Cover and. Filter Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove

More information

Performer-Plus 5.0L Hydraulic Roller Lifter Camshaft only CATALOG #3722 MODEL: 5.0 Litre Ford V8, 1985 & later INSTRUCTIONS

Performer-Plus 5.0L Hydraulic Roller Lifter Camshaft only CATALOG #3722 MODEL: 5.0 Litre Ford V8, 1985 & later INSTRUCTIONS Performer-Plus 5.0L Hydraulic Roller Lifter Camshaft only CATALOG #3722 MODEL: 5.0 Litre Ford V8, 1985 & later INSTRUCTIONS PLEASE study these instructions carefully before installing your new camshaft.

More information

Workshop Manual. F-Super Duty : Powertrain. 03: Engine

Workshop Manual. F-Super Duty : Powertrain. 03: Engine Workshop Manual 1999 F-Super Duty 250-550 3: Powertrain 03: Engine 1999 F-Super Duty 250-550 Contents/Index GROUP 03: Engine SECTION 303-00: Engine System General Information SECTION 303-01A: Engine 5.4L

More information

Displacement 5.3L 325 CID. Stroke 92.0 mm in. Firing Order Spark Plug Gap 1.02 mm 0.04 in

Displacement 5.3L 325 CID. Stroke 92.0 mm in. Firing Order Spark Plug Gap 1.02 mm 0.04 in Enge Mechanical Specifications (RPO LMG VIN 0) Specification Application Metric English General Enge Type V8 Displacement 5.3L 325 CID RPO LMG VIN 0 Bore 96.0-96.018 3.779-3.78 Stroke 92.0 3.622 Compression

More information

2014 RAM C/V Tradesman

2014 RAM C/V Tradesman Fig. 91: Suction Hose Ball Valve NOTE: View typical 14. Open the suction hose's ball valve to begin refilling the cooling system. 15. When the vacuum gauge reads zero, the system is filled. NOTE: On some

More information

Ford 4.6L (2V) SPECIFICATIONS

Ford 4.6L (2V) SPECIFICATIONS Ford 4.6L (2V) SPECIFICATIONS General Specifications Item Specifications Silicone Gasket and Sealant F7AZ-19554-EA WSE-M4G323-A4 Premium Engine Coolant VC-4A, VC-5 in Oregon, CXC-10 in Canada ESE-M97B44-A

More information

SECTION D Engine 6.0L Diesel

SECTION D Engine 6.0L Diesel 303-01D-i Engine 6.0L Diesel 303-01D-i SECTION 303-01D Engine 6.0L Diesel CONTENTS PAGE DESCRIPTION AND OPERATION Engine... 303-01D-2 303-01D-2 Engine 6.0L Diesel 303-01D-2 DESCRIPTION AND OPERATION Engine

More information

DIESEL ENGINE MECHANICAL

DIESEL ENGINE MECHANICAL SECTION 1B3 DIESEL ENGINE MECHANICAL CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

PONTIAC SHOP MANUAL

PONTIAC SHOP MANUAL 6--0 1955 PONTIAC SHOP MANUAL Fig. 6-1 Pontiac Strato Streak V-8 Engine Fig. 6-2 Pontiac Strato Streak V-8 Engine ENGINE MECHANICAL 6-1 ENGINE MECHANICAL CONTENTS OF THIS SECTION SUBJECT PAGE SUBJECT PAGE

More information

1992 Toyota Cressida

1992 Toyota Cressida Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May

More information

2000 Toyota Truck Tundra. Timing Belt: Service and Repair

2000 Toyota Truck Tundra. Timing Belt: Service and Repair Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE

More information

2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]

2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S] 2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S] 1988 Toyota Celica 1988 TOYOTA ENGINES 2.0L & 2.0L Turbo 4-Cylinder Celica * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,

More information

1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder

1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness

More information

1-3/4" or 1-7/8" headers Aftermarket/re-curved distributors

1-3/4 or 1-7/8 headers Aftermarket/re-curved distributors TORKER-PLUS Camshaft/Lifters/Lube Kit #5062 for 1967 & later 396-454 c.i.d. Chevrolet (not for use in 1965-66 396 & 427 engines requiring grooved rear journal) PLEASE study these instructions carefully

More information

Skirted GEN III - Technical Notes

Skirted GEN III - Technical Notes DART Skirted GEN III - Technical Notes Deck Height... 9.240-9.450 STD or Raised cam, 9.750 9.950 Raised cam only Bore... 4.000 & 4.125 Main Bearing Size... LS-1 (2.558" 2.559") Weight... 115lbs 4.125 and

More information

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html Page 1 of 7 NOTE: The timing pin is used to accurately locate TDC for setting the overhead. The timing pin is typically located below the fuel pump. for front gear train engines, in the front gear housing

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

Piston diameter should be measured at normal room temperature of 70 F (21 C).

Piston diameter should be measured at normal room temperature of 70 F (21 C). Piston & Rod Assembly 1. Pistons are not interchangeable from bank to bank. Pistons are marked L and R (left and right) and must be installed with arrow on top of piston pointing toward front of engine.

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking

More information

Intake Manifold: Service and Repair Removal

Intake Manifold: Service and Repair Removal 1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling

More information

Page 1 of 9 303-01C Engine 6.0L Diesel 2004 F-Super Duty 250-550/Excursion DESCRIPTION AND OPERATION Procedure revision date: 08/06/2003 Engine Printable View Engine Description The 6.0L diesel engine

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL. 411 718 38 3 1027 1 127 127 127A 1080 1081 1028 127 718A 127 718 44B 718A 2 44A 493 44 1069 112 718B 1019 LABEL KIT 1058 OWNER S MANUAL

More information

Valve Lash and Valve Bridge Adjustment

Valve Lash and Valve Bridge Adjustment Valve Lash and Valve Bridge Adjustment Illustration 1 g00286271 (1) 147-2060 Wrench (2) 147-2059 Torque Wrench (3) 148-7211 Bridge Nut Socket (4) 145-5191 Gauge Support (5) 147-2056 Dial Indicator (6)

More information

Page 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

TORKER-PLUS Camshaft/Lifters/Lube Kit CATALOG #5002 MODEL: c.i.d. Chevrolet V8

TORKER-PLUS Camshaft/Lifters/Lube Kit CATALOG #5002 MODEL: c.i.d. Chevrolet V8 PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or problems, do not hesitate to call our Technical Hotline at: 1-800-416-8628. CAMSHAFT: Edelbrock

More information

Page 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T-12270-A Removal NOTE: It is

More information

Timing Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A.

Timing Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A. 1997 Chevrolet Cavalier L4-144 2.4L DOHC VIN T SFI Page 1 Timing Chain: Service and Repair With 2 Piece Tensioner (TSB 67-61-22A) Precaution Bulletin No.: 67-61-22A Date: July, 1998 TIMING CHAIN TENSIONER

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET

WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET APPLICATIONS: WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P 262-400 SMALL BLOCK CHEVROLET INSTALLATION INSTRUCTIONS The P/N 8125 & 8126 WEIAND STREET WARRIOR series intake manifolds

More information

EXHAUST SYSTEM AND INTAKE MANIFOLD

EXHAUST SYSTEM AND INTAKE MANIFOLD J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST

More information

ENGINE OVERHAUL GROUP 11B 11B-1 CONTENTS GENERAL SPECIFICATIONS... 11B-2 OIL PAN AND TIMING CHAIN CASE... 11B-27 SERVICE SPECIFICATIONS...

ENGINE OVERHAUL GROUP 11B 11B-1 CONTENTS GENERAL SPECIFICATIONS... 11B-2 OIL PAN AND TIMING CHAIN CASE... 11B-27 SERVICE SPECIFICATIONS... 11B-1 GROUP 11B CONTENTS GENERAL SPECIFICATIONS 11B-2 SERVICE SPECIFICATIONS 11B-2 FASTENER TIGHTENING SPECIFICATIONS 11B-4 SEALANTS AND ADHESIVES 11B-7 SPECIAL TOOLS 11B-8 GENERATOR AND IGNITION SYSTEM

More information

M-6007-Z363 Crate Engine Specifications and Owner's Manual

M-6007-Z363 Crate Engine Specifications and Owner's Manual M-6007-Z363 Crate Engine Specifications and Owner's Manual!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. INSTALLATION INSTRUCTIONS: These instructions consist of (4)

More information

M-6007-Z351SR Sealed Crate Engine INSTRUCTION SHEET

M-6007-Z351SR Sealed Crate Engine INSTRUCTION SHEET Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009

Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009 1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 1 Technical Service Bulletin # 98-107 Date: 990111 Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009 Reference:

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

Page 1 of 5 Service Manual: TIMING BELT REPLACEMENT - 3.2L & 3.5L REMOVAL & INSTALLATION 1999 Chrysler 300M 3.5L Eng Question: Is a 3.5 a valve bender? - My Autodata book says every car is bender REMOVAL

More information

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: 262-400 c.i.d. Chevrolet V8, 1957 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions

More information

Twisted Wedge 11R Aluminum Cylinder Heads

Twisted Wedge 11R Aluminum Cylinder Heads Twisted Wedge 11R Aluminum Cylinder Heads for the Small Block Ford Thank you for purchasing Trick Flow Twisted Wedge 11R aluminum cylinder heads designed for the Small Block Ford. Please follow the steps

More information

DART Aluminum FORD 351 Small Block Technical Notes

DART Aluminum FORD 351 Small Block Technical Notes DART Aluminum FORD 351 Small Block Technical Notes Deck Height 9.200 & 9.500 Bore 4.00 or 4.125 unfinished Main Bearing Size 302 (2.249 ) or 351C (2.749 ) Weight. 9.200 91 lb / 9.500 93 lb Maximum bore

More information

PERFORMER-PLUS Camshaft/Lifters/Lube Kit #2177 MODEL: c.i.d. Chrysler V8, 1967 & later (Not for 1985 & later 318 V8 with roller lifters)

PERFORMER-PLUS Camshaft/Lifters/Lube Kit #2177 MODEL: c.i.d. Chrysler V8, 1967 & later (Not for 1985 & later 318 V8 with roller lifters) PERFORMER-PLUS Camshaft/Lifters/Lube Kit #2177 MODEL: 318-360 c.i.d. Chrysler V8, 1967 & later (Not for 1985 & later 318 V8 with roller lifters) PLEASE study these instructions carefully before installing

More information

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E TIMING CHAIN Removal and Installation PFP:13028 EBS00I2X A EM C D E F G H I J K L M KBIA2511E EM-35 1. Camshaft sprocket (left bank EXH) 2. Camshaft sprocket (left bank INT) 3. Camshaft sprocket (right

More information

2.4L 4-CYL - VINS [F,H,S]

2.4L 4-CYL - VINS [F,H,S] 2.4L 4-CYL - VINS [F,H,S] 1990 Nissan 240SX 1990 ENGINES Nissan 2.4L 4-Cylinder Axxess, Pickup, Stanza, 240SX * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD RACING PERFORMANCE PARTS. STOP! READ THIS!

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD RACING PERFORMANCE PARTS. STOP! READ THIS! STOP! READ THIS! THIS ENGINE REQUIRES RACING OIL THAT CONTAINS 1200 PPM (parts per million) ZDDP (zinc-dialkyl-dithio-phosphate). THIS ENGINE IS SHIPPED WITHOUT OIL! Page 1 of 6 Please contact the Tech

More information

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7194 MODEL: c.i.d. Chrysler V8, 1968 & later

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7194 MODEL: c.i.d. Chrysler V8, 1968 & later PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 413-426-440 c.i.d. Chrysler V8, 1968 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions, do

More information

Installation Manual For ISL98, ISL03, ISL07, ISC07

Installation Manual For ISL98, ISL03, ISL07, ISC07 Installation Manual For ISL98, ISL03, ISL07, ISC07 Table of Contents Section 1: Introduction... 3 Housing Identification... 3 Engine Identification... 3 Special Tools... 3 Automatic Transmissions... 3

More information

11A-1 ENGINE CONTENTS

11A-1 ENGINE CONTENTS 11A-1 ENGINE CONTENTS ENGINE ENGINE ... 11A... 11B 11A-2 ENGINE CONTENTS GENERAL... 3 Outline of Changes... 3 GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL

More information

M-6007-A50NA Engine Specifications and Owner's Manual

M-6007-A50NA Engine Specifications and Owner's Manual M-6007-A50NA Engine Specifications and Owner's Manual Fordracingparts.com Techline 1-800-367-3788 Page 1 of 11 IS-1850-0377 Please visit www.fordracingparts.com for the most current instruction information.!!!

More information

Iron GEN III - Technical Notes

Iron GEN III - Technical Notes DART Iron GEN III - Technical Notes Deck Height... 9.240" Bore... 4.000 & 4.125 Main Bearing Size... LS-1 (2.558" 2.559") Weight... 227lbs Largest Recommended Bore..... 4.185" Largest Recommended Crank

More information

ENGINE MECHANICAL EM SECTION CONTENTS

ENGINE MECHANICAL EM SECTION CONTENTS ENGINE MECHANICAL EM SECTION CONTENTS INTAKE MANIFOLD...EM-2 Component Parts Location...EM-2 Removal and Installation...EM-3 Inspection...EM-3 EXHAUST MANIFOLD...EM-4 Component Parts Location...EM-4 Removal

More information

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD RACING PERFORMANCE PARTS.

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD RACING PERFORMANCE PARTS. Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

2006 Eclipse 3.8L V6 models produced between 6/13/05 6/22/05 (between VIN 6E VIN 6E005929)

2006 Eclipse 3.8L V6 models produced between 6/13/05 6/22/05 (between VIN 6E VIN 6E005929) Page 1 of 8 SUBJECT: ENGINE TICKING NOISE DATE: July, 2005 No: MODEL: 2006 Eclipse CIRCULATE TO: [ ] GENERAL MANAGER [X] PARTS MANAGER [X] TECHNICIAN [X] SERVICE ADVISOR [X] SERVICE MANAGER [X] WARRANTY

More information

Valve gear, servicing

Valve gear, servicing Page 1 of 62 15-1 Valve gear, servicing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail if

More information

PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: c.i.d. Pontiac V8, 1965 & later

PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: c.i.d. Pontiac V8, 1965 & later PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: 350-455 c.i.d. Pontiac V8, 1965 & later CAMSHAFT: Edelbrock Performer-Plus camshafts are ground specifically for use with the corresponding

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble (2 34 8) Special Tools 2-036A Remover for pilot bearing 2-37 Oil seal installer/aligner 237 2036A 2-044A Installer/Aligner, Pilot Bearing/Clutch Plate 244 2-44 Inlet manifold

More information

Water Pump Replacement (L4)

Water Pump Replacement (L4) 1 of 9 9/5/2017, 3:07 PM 2014 Chevrolet Captiva (VIN C) Antara, Captiva Service Manual 5565211 Engine/Propulsion Engine Cooling Repair Instructions Document ID: 2643411 Water Pump Replacement (L4) Special

More information