TIMING BELT TENSIONER FOR AFTERMARKET TENSIONER P/N FORD U.K. 1.8L 4-Cyl. Diesel Revision date: 06/17/1999
|
|
- Rhoda O’Brien’
- 6 years ago
- Views:
Transcription
1 1. Failure to set belt tension correctly to this procedure will result in premature engine failure! 2. The Auto-tensioner is a thermal expansion compensation device so tensioning should only be carried out after letting the engine cool for a minimum of 3 hours. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto a hot engine. 3. Never reuse old belts and always replace both Camshaft and Fuel Injection Pump belts together. Initial Removal of Timing Belt and Tensioner 4. Turn the crankshaft in the normal direction of rotation of the engine (clockwise) until the slot in the injection pump timing belt is at 11 o clock (See Figure 1). 5. Unscrew the blanking plug and insert the crankshaft TDC pin (pt# B). Make sure TDC pin is fully seated (See Figure 2). 6. Turn the crankshaft carefully until it comes up against the TDC pin (See Figure 2). 7. Undo the Eccentric Idler center bolt and set the idler teardrop to 6 o clock position (See Figure 3). 8. Insert the alignment tool (pt# B) in the slot on the camshaft and ensure fully home (See Figure 4). 9. Undo the camshaft pulley timing bolt three full revolutions. 10. Free the camshaft timing pulley from the taper by inserting a screwdriver between the pulley and the back plate, and then strike the back plate with a soft metal drift (See Figure 5). 11. Remove cam pulley, tensioner, and camshaft timing belt. Installation of Timing Belt and Tensioner 12. Install new Tensioner torque mounting bolts to manufactures specifications. Route new timing belt around system, Make sure direction arrows on the belt are in the direction of engine rotation and that it is correctly seated. Finish by installing cam-pulley into belt and installing pulley over end of camshaft nose. 13. Lightly oil between the head and the captive washer of the camshaft pulley bolt, finger tighten bolt until it touches the pulley, then back off one quarter turn. Ensure pulley is still free to rotate on camshaft taper. Page 1/8
2 Belt pre-tensioning and Belt Settlement 14. Lightly oil under head of eccentric idler bolt. Turn idler teardrop to 9 o clock position then torque bolt to 20 Nm (See Figure 6). 15. Torque cam-pulley center bolt to torque 20 Nm while using reaction tool (pt# A) to stop any movement of the pulley (See Figure 9). 16. Remove Crankshaft TDC pin (pt# ) and camshaft timing plate (pt# B). 17. Rotate the crankshaft two (2) complete revolutions in the normal direction of engine rotation (clockwise) manually for proper seating of the belt. (This can be achieved with one of the front wheels raised with the engine in gear and manually turning the wheel.) Initial Belt Tensioning 18. Turn the crankshaft in the normal direction of rotation of the engine (clockwise) until the slot in the injection pump timing belt is at 11 o clock (See Figure 1). 19. Insert the crankshaft TDC pin (pt# B). Make sure TDC pin is fully seated (See Figure 2). 20. Turn the crankshaft carefully until it comes up against the TDC pin (See Figure 2). 21. Undo the Eccentric Idler center bolt through half a turn. 22. Insert the alignment tool (pt# B) in the slot on the camshaft and ensure fully home (See Figure 4). 23. Undo the camshaft pulley timing bolt three full revolutions. 24. Free the camshaft timing pulley from the taper by inserting a screwdriver between the pulley and the back plate, and then strike the back plate with a soft metal drift (See Figure 5). 25. Finger tighten the camshaft pulley bolt until it touches the pulley, then back off one quarter turn. Ensure pulley is still free to rotate on camshaft taper. 26. Turn eccentric idler clockwise using a Allen key until the auto-tensioner just comes up to the right hand edge of the setting window in a clockwise direction, hand tighten up eccentric idler center bolt. N.B. Pointer will move from right to left as tension is increased in the belt. (use a mirror to achieve a better view of auto tensioner.) See figure 7 and Torque eccentric idler center bolt to Nm using Allen key to react against any movement achieved by friction under bolt head. 28. Recheck auto-tensioner pointer position, if between right hand edge of setting window and the center, continue process. If not return to step 26. Page 2/8
3 29. Torque cam-pulley center bolt to torque (30-36Nm for M8 bolt, 45-55Nm for M10 bolt) while using reaction tool to stop any movement of the pulley. Failure to prevent rotation of the pulley will result in incorrect belt tension (See Figure 9). Final Check, Belt Tensioning 30. Recheck auto-tensioner pointer position, if within window continue process if not within window return to step 23 and continue from that point. Note: Failure to ensure tension is set within window on a cold engine will result in premature engine failure (See Figure 10). 31. Remove Crankshaft TDC pin (pt# ) and camshaft timing plate (pt# B). 32. Rotate the crankshaft two (2) complete revolutions in the normal direction of engine rotation (clockwise) manually to ensure proper seating of the belt. (This can be achieved with one of the front wheels raised with the engine in gear and manually turning the wheel.) 33. Turn the crankshaft clockwise until the slot in the injection pump timing belt pulley is at 11 o clock (See Figure 1). 34. Insert the crankshaft TDC pin, making sure pin is fully seated (See Figure 2). 35. Turn the crankshaft carefully until it comes up against the TDC pin (See Figure 2). 36. Insert the alignment tool (21-162B) in the slot on the camshaft and ensure fully home (See Figure 4). 37. Recheck auto-tensioner pointer position, if within window continue process (see figure 10), if not within window return to step 23 and continue from that point. Note: Failure to ensure tension is set within window on a cold engine will result in premature engine failure. 38. Remove Crankshaft TDC pin (pt# ) and camshaft timing plate (pt# B), reinstall blanking plug. 39. Reassemble engine assembly. Page 3/8
4 Figure 1: Injection pump timing at 11 o clock Figure 2 TDC pin installation Page 4/8
5 Figure 3: Idler teardrop at 6 o'clock position Figure 4: Installation of alignment tool Page 5/8
6 Figure 5: Freeing up of camshaft timing pulley Figure 6: Idler teardrop at 9 o clock Page 6/8
7 Figure 7: eccentric idler adjustment Figure 8: Tensioner initial set position Page 7/8
8 Figure 9: Torque procedure for cam pulley Figure 10: Final auto-tensioner pointer positio Page 8/8
ATech Timing Belt Tensioner (979572) VM MOTORI 2.5L Diesel, Common Rail Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More informationPage 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft
More informationService and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
More informationSized for Print. Timing belt, replacing. Special tools: COUNTERHOLD See: Tools and Equipment\ Counterhold
Timing belt, replacing Special tools: 999 5433 COUNTERHOLD See: Tools and Equipment\999 5433 Counterhold Note! Since the illustrations in this service information are used for different model years and/or
More information1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
More information2001 Escort Workshop Manual
Page 1 of 6 SECTION 303-01B: Engine 2.0L Zetec 2001 Escort Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/26/2004 Timing Drive Components Timing Belt Special Tool(s) Crankshaft TDC Timing
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More informationReplacing timing belt
"VCC001207 EN 20100809" 1(5) Replacing timing belt Special tools: 998 8500, 999 5456 spark plugs cover two fuel lines clamps lift up expansion tank and place over engine to one side front timing cover
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More informationTiming Belt, Replacing
Page 1 of 8 2004 Volvo XC70 L5-2.5L Turbo VIN 59 B5254T2 Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Timing Belt, Replacing Timing Belt, Replacing Timing belt, replacing
More informationRecommended Installation Procedure ATech Timing Belt Tensioner and AUDI 2.0L 4V FSI & TFSI Engine (19 January 2015)
The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must be installed
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationRECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationRecommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure (31 MARCH 2010) ATech Timing Belt Tensioner (979004) EA T 20 Valve Longitudinal Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationTiming Belt: Service and Repair
2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata
More informationReplacing the oil pump / front crankshaft seal
"VCC097797 EN 20100518" 1(5) Replacing the oil pump / front crankshaft seal Special tools: 998 6187, 999 5433, 999 5455, 999 5919, 999 5747, 951 2050 Note! As the illustrations in the information are used
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More informationATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure ATech Timing Belt Tensioner DaimlerChrysler PL, PT, JR 2.0L 4-Cyl. Engine (10/27/2003)
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to DAIMLERCHRYSLER PL s guidelines. The mounting of the TBT
More informationTIMING BELT REPLACEMENT. Removal Procedure. Tools Required J Timing Belt Alignment Kit J Crank Hub Torx Socket
1 of 15 3/19/2012 5:34 PM TIMING BELT REPLACEMENT Removal Procedure Tools Required J 42069 Timing Belt Alignment Kit J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationTIMING BELT (3S FE) COMPONENTS
Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE
More informationRemoving and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More informationService and Repair REPLACING TIMING BELT/IDLER PULLEY/BELT TENSIONER. Special Tools:
1 of 9 6/18/2008 8:48 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1999 Volvo V70 XC AWD L5-2.4L Turbo VIN 56 B5254T Vehicle
More informationALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)
ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
More informationTIMING BELT TIMING BELT
TIMING BELT TIMING BELT DISASSEMBLY 1. Lift the vehicle by using of jack. 2. Remove the engine support bracket. (14 mm bolt and 2 nuts, 17 mm bolt) 3. Remove the power steering belt. 4. Remove the air
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for Fiat Doblò panel van/station wagon (263) 1.6 D Multijet ContiTech shows how to avoid errors when changing belts Large numbers
More informationTIMING BELT TENSIONER FOR AFTERMARKET RENAULT G8T 2.2L DIESEL ENGINE (Revision date: 06/24/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for a CT1015 WP1 and CT1018K1 in an Audi A4 (B6) 2.5-liter V6 TDI with engine code AKE MY 2001 ContiTech shows how to avoid errors
More informationTECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
More informationREMOVAL AND INSTALLATION
2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More information1998 Honda Accord EX
Installation (New Belt) 1. Ensure that engine is at TDC. Align dimple on timing belt drive pulley with pointer on oil pump. See Fig. 4. Align camshaft pulleys with pointers on back covers. 2. Remove battery
More informationReplacing the timing belt
"VCC116740 EN 20091209" 1(5) Replacing the timing belt Special tools: 999 5433, 999 5456 Removing the timing belt Note! As the illustrations in this service information are used for different model years
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationReplacing the camshaft seals / variable valve timing (VVT) unit
"VCC097794 EN 20100918" 1(10) Replacing the camshaft seals / variable valve timing (VVT) unit Special tools: 951 2050, 999 5450, 999 5451, 999 5452, 999 5651, 999 5718, 999 5719, 999 5919 Note! As the
More informationToyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT
More informationTech Talk. Timing Belt 6VD1/6VE1
Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the
More informationService and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
More informationINSTALLATION. Check that the idler pulley moves smoothly.
ENGINE MECHANICAL (5SFE) INSTALLATION EM23 EM08604 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000,
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More information2002 Escape Workshop Manual
SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in
More informationTIMING BELT (5S FE) COMPONENTS
ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds
More informationReplacing the camshaft seals / variable valve timing (VVT) unit
"VCC097794 EN 20110521" 1(10) Replacing the camshaft seals / variable valve timing (VVT) unit Special tools: 951 2050, 999 5450, 999 5451, 999 5452, 999 5651, 999 5718, 999 5719, 999 5919 Note! As the
More informationKD Disassembly/ Assembly recommendations
KD457.48 Disassembly/ Assembly recommendations AUDI: SKODA: VOLKSWAGEN: KD457.48/UK/01-05/2016 A4 (Series 2, 2 FL, Cabriolet), A6 (Series 2, 2FL, Allroad), A8 Superb Passat ENGINES 2.5TDi TIMING BELT DIAGRAM
More information- 1/7 - Copyright Litens Automotive Group All rights reserved.
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More information5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.
More informationEG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
More informationFiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan.
Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Introduction This document outlines how to replace a timing belt on a Fiat X1/9 1500cc
More informationD8 - Distributor. D9 - Auxiliary unit belts
D8 - Distributor l ubricate Lubricate the distributor shaft sparingly (1-2 drops of oil) D9 - Auxiliary unit belts check/adjust Applies to engines which do not have multi-tooth belts Check belt tension.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationClassification: Reference: Date: VE30DE CAM TIMING
Classification: Reference: Date: EM93-002 NTB93-126 September 2, 1993 VE30DE CAM TIMING APPLIED VEHICLE(S): All equipped with VE30DE Engine SERVICE INFORMATION When servicing VE30DE engine cylinder heads,
More informationFig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover
Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and
More informationTiming Belt: Service and Repair TIMING BELT
2003 Hyundai Truck Santa Fe V6-2.7L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT TIMING BELT 2.7L REMOVAL 1. Remove the engine cover. 2. Using a [16 mm], rotate the
More informationTiming Belt: Service and Repair Dismantling the Belt Drive. Dismantling Belt drive, dismantling Special tools: , ,
2005 Volvo XC90 L5-2.5L Turbo VIN 59 B5254T2 Page 1 Timing Belt: Service and Repair Dismantling the Belt Drive Dismantling Belt drive, dismantling Special tools: 999 5304, 999 5433, 999 5747 Note: As the
More informationDISASSEMBLY. SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System
SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System DISASSEMBLY 1. Remove the engine cover. 2. Disconnect the battery negative terminal. 3. Disconnect the radiator lower hose. 4. Disconnect the
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More informationREMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
More informationTiming Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.
Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,
More information8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More information2003 Hyundai Truck Santa Fe V6-3.5L
Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the
More informationVALVE CLEARANCE INSPECTION
EM4 ENGINE MECHANICAL (5VZFE) INSPECTION EM01E10 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE INTAKE AIR CONNECTOR (See page EM29) 2. REMOVE CYLINDER HEAD COVERS (See page
More informationAccurate guidelines for longer engine life
VOLKSWAGEN VOLVO Issue 16 2013 VKMC 01270 VKMC 01258-1 VKMC 01258-2 Accurate guidelines for longer engine life Many technicians are taking chances by not following all the manufacturer recommendations
More informationTIMING BELT (4A FE) COMPONENTS
EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE
More informationTiming Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar
Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer
More informationTechnical Info. Installation tips: Opel Vectra B 1,6i 16 V X16 XEL
The engine of the Opel Vectra B 1.6i 16 V and other engines with similar displacement are also installed in other Opel vehicles in large quantities. Usually, changing the timing belt is not problematic,
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for CT881K2 / CT881WP1 timing belt kit in a Ford Fiesta V MY 2004 (JH_JD_) 1.4-liter 16 V with engine code FXJA ContiTech shows how
More informationTiming belt replacement intervals
Important note Important note The intervals and procedures given are subject to alteration by the manufacturer at any time. Check the regularly updated Timing Belts section on our website to ensure that
More informationTiming Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A.
1997 Chevrolet Cavalier L4-144 2.4L DOHC VIN T SFI Page 1 Timing Chain: Service and Repair With 2 Piece Tensioner (TSB 67-61-22A) Precaution Bulletin No.: 67-61-22A Date: July, 1998 TIMING CHAIN TENSIONER
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner
More informationREMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
More informationContiTech: Expert Tips on Replacing Timing Chains
Practical Tip ContiTech Power Transmission Group ContiTech: Expert Tips on Replacing Timing Chains Detailed instructions for a TC 1003K1 in a 1.2 l VW Polo with engine code BMD, model year 2010 ContiTech
More informationIMING BELT COMPONENTS REMOVAL
1 of 11 11/21/2012 2:21 PM IMING BELT COMPONENTS REMOVAL 1. Remove the wheel of passenger side. 2. Remove the side cover. 3. Remove the engine cover. 4. Disconnect the power steering hose fixing on the
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More informationTiming Chain - Renew ( )
«Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More informationRecommended Installation Procedure (25 MAY 07) ATech Timing Belt Tensioner (979778) FIAT FIRE 8-valve 1.2/1.4L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationFord Focus Zetec SVT Timing Belt
2000-2004 Ford Focus Zetec SVT Timing Belt Replacement This guide will show you how to replace the timing belt on the 2.0L DOHC Zetec with VCT on a 2002 Ford Focus SVT. This is an interference motor. Written
More information