FLUIDS AND LUBRICANTS

Size: px
Start display at page:

Download "FLUIDS AND LUBRICANTS"

Transcription

1 SECTION / JL07 IMPORTANT NOTICE The following information is a summary of the standards, recommendations and specifications of our suppliers and is taken from documents produced by them, with regard to the maintenance of the components that they manufacture. This information has been verified and is up-to-date as of the date of this publication. The information reproduced in this section has been prepared strictly as a quick reference. Please note that the standards, recommendations and specifications of our suppliers can vary at any time. Our supplier s manuals have precedence over this document, and it is the user s responsibility alone, to obtain the latest updated versions. Nova Bus assumes no responsibility for any damages or losses incurred as a result of not obtaining the most recent updates. The efficiency and life of any mechanical equipment is largely dependent upon proper lubrication and servicing. All mechanical components rely on a lubricating film between moving parts to reduce friction, prevent wear, help cool the contacting sliding parts, and keep dirt and wear particles away from mating parts. Proper lubrication depends upon using the right type of lubricant at proper intervals and filling to proper capacities. This section provides a MAINTENANCE SCHEDULE for parts requiring a periodic lubrication. The locations of those parts are shown in Figure 1 through 3, depending on the model of the vehicle. CHARACTERISTICS Recommended lubricants are indicated in the Maintenance Schedule. A description of each type of lubricant is provided in the following paragraphs. See Table 1: LUBRICANT SPECIFICATIONS. When choosing the appropriate lubricant, you must take into consideration the oil supplier s reputation. The supplier must be accountable for the quality of the product. Lubricant descriptions will allow the transit authority to demand the appropriate type and quality. ENGINE OIL Oil companies sell various types of engine oil under certain maintenance designations and technical specification numbers. By choosing a reliable supplier and paying special attention to the recommendations regarding oil and filter changes, you will get satisfactory lubrication and a longer life span for your engine. The engine manufacturer recommends using a high-quality SAE 15W-40 lubricating oil all year round that meets American Petroleum Institute (API) performance classification CG-4SF ou CF-4SFw. CAUTION: The use of particular mixes of complementary additives or concentrates (such as anti-smoking, covering, or deodorizing agents, tuning primers, superior grade oil, breaking-in oils, graphite lubricants, and anti-friction compounds) is not recommended as greasing oil used for diesel engines. For further details concerning lubricating oils for Cummins, please see CUMMINS ENGINE OIL RECOMMENDATIONS and section : CUMMINS ENGINE LUBRICATION of this manual.

2 2009JL07 2 / LUBRICANT SPECIFICATIONS ENGINE OIL AUTOMATIC TRANSMISSION ELECTRIC DRIVE DIFFERENTIAL OIL MULTIPURPOSE CHASSIS GREASE STEERING GEAR OIL HYDRAULIC OIL SPECIFICATIONS SAE 15W-40 (API) classification CG-4SF ou CF-4SFw. See transmission manufacturer s documentation. Drive oil (TranSynd for Allison Electric Drive ONLY) Hypoid Gear oil GL-5, SAE 80W90 Meeting MIL-L-25-D Universal Joint Grease NLGI Grade 2, Lithium 12-Hydroxy Stearate with Molybdenum Disulfide Dexron-III type Automatic Transmission Oil Dexron-III type Table 1 - Lubricant Specifications POWER STEERING FLUID Dexron III or Hydrex XV should be used in the hydraulic reservoir. Refer to section 09: HYDRAULIC SYSTEM in this manual for oil filter replacement and system purge. AUTOMATIC TRANSMISSION FLUID The transmission oil supplied with the vehicle may vary, depending on the type of transmission installed. See section : TRANSMISSION for procedures on fluid checks, filter and fluid change. See the transmission manufacturer s documentation, supplied with the vehicle, regarding the appropriate types of oil to be used, as well as recommended oil change intervals. DRIVE FLUID (HEV) The fluid used in the drive on the Nova Bus LFS-HEV is TranSynd, distributed exclusively by Allison Electric Drive (AED). Refer to the drive manufacturer s service manuals provided by Nova Bus for detailed information concerning the drive fluid. See section : ALLISON ELECTRIC DRIVE E P -40, as well as Allison Electric Drive s Service manuals for procedures on fluid checks, filter and fluid change. HYPOID GEAR OIL A multigrade gear oil SAE 80W/90, API GL-5 is recommended for year-round service to lubricate the rear axle, even under maximum torque and speed conditions. This oil is also recommended for front axle bearing lubrication. See the axle manufacturer s Service Manuals, provided by Nova Bus, for detailed information on oil checks, change and filling. MULTIPURPOSE GREASE This lubricant should be a good quality grade 2 lithium soap multipurpose chassis grease. It must be designed to offer protection against water and corrosion and to withstand extreme pressure and high temperatures. It also must have a melting point of approximately 520 F (270 C). Starplex 1 or 2 is an example of this type of grease. COOLANT AND ANTIFREEZE See section 09: ENGINE COOLING for more information on the recommended products.

3 / JL07 LUBRICATION PROCEDURES This heading only mentions a few particular procedures and safety measures. For any other procedure linked to the lubrication of a component, such as removal, installation, disassembly, cleaning, etc., see the corresponding section of this manual or the manufacturer s maintenance manual. CAUTION: All grease fittings must be cleaned before applying the lubricant. Also, make sure the equipment used to apply the lubricant is clean. Every precaution must be taken to avoid the penetration of dirt, abrasive dust, lint, or other foreign matter in the lubricant containers. Replace broken, damaged or defective fittings. WARNING: Respect all security instructions and rules during any lubrication activity or maintenance inspection. DRIVESHAFT LUBRICATION The universal joints and the sliding joint of the driveshaft require a particular lubrication procedure. It is important to consult section -501: DRIVESHAFT, as well as the manufacturer s documentation, before performing driveshaft lubrication. Also see the manufacturer s documentation for approved lubricants. WHEEL BEARING LUBRICATION Instructions for removing, installing and adjusting the wheel bearings can be found in the axle manufacturer s service manual. CLEANING Thoroughly clean the wheel bearings and the wheel hubs with a stiff-bristled brush and some solvent to remove all traces of old lubricant and dirt. Check that the bearings are not damaged and have them replaced, if necessary. APPLICATION CAUTION: When applying lubricant by hand, ensure that sufficient grease penetrates the spaces between the rollers and the bearing race. A mechanical greaser may also be used, but make sure the bearings are thoroughly lubricated. Clean the bearings and the hub cavity on the inside diameter of the bearing holders. Also, clean the filling cavity at the hub extremities of the driving axles, between the outside bearing and the joint seal. The amount of lubricant inside the hubs must not exceed the capacity of the bearing holders. The amount of bearing lubricant is sufficient to provide adequate lubrication until the next scheduled maintenance. MAINTENANCE SCHEDULE For item numbers, see Figures 1 or 2 according to vehicle type. The maintenance schedule is intended to serve as a ready reference for systems and components that require periodic lubrication. The maintenance schedule consists of general recommendations based on the manufacturer s specifications for the type of fluid supplied at time of delivery of the vehicle. Consult the annexes at the end of this document to obtain the maintenance schedule applicable to your vehicle: MODULE A: Bus with ZF transmission MODULE B: Bus with Voith transmission MODULE C: Bus with Allison transmission MODULE D: Bus with Allison E P -40 drive The ONLY suitable way to establish intervals of adequate oil draining is to proceed by analysis. Analysis of the engine oil, the power steering fluid, the automatic transmission fluid (or drive fluid) and hypoid oil ensures that the viscosity of oil is within the range allowed by the manufacturer. The lubrication of some items listed below may be part of an optional manual greasing system. See section 08: MANUAL GREASING SYSTEM to obtain more details on the system and the greasing points. In this case, disregard the corresponding lubricant specification and use Multipurpose Chassis Grease EP1/EP2. An automatic greasing system can also manage the lubrication of certain components. See section 08: AUTOMATIC GREASING SYSTEM for more details.

4 2009JL07 4 / WIPER POST 2. MITER BOX 3. BRAKE PEDAL 4. ACCELERATOR PEDAL 5. WINDSHIELD WASHER RESERVOIR 6. INTERMEDIATE STEERING SHAFT 7. STEERING SHAFT 8. BATTERY TERMINALS 9. BATTERY TRAY GUIDE RAIL. DOOR RODS AND LEVER 11. FRONT ACCESS RAMP (OPTIONAL) 12. STEERING GEARBOX 13. AUTOMATIC GREASING RESERVOIR 14. DRAG LINK END 15. STEERING KNUCKLES. WHEEL BEARING 17. TIE ROD END 18. REAR ACCESS RAMP (OPTIONAL) 19. DIFFERENTIAL 20. DRIVESHAFT UNIVERSAL JOINT 21. DRIVESHAFT SLIDING JOINT 22. TRANSMISSION/DRIVE DIPSTICK 23. TRANSMISSION/DRIVE OIL FILTER 24. FUEL FILTER 25. TRANSMISSION/DRIVE OIL PAN 26. RADIATOR 27. ENGINE OIL FILTER FILTER 28. ENGINE COOLANT FILTER 29. ENGINE DIPSTICK 30. COOLANT SURGE TANK 31. HYDRAULIC RESERVOIR 32. A/C COMPRESSOR (OPTIONAL) 33. COOLANT FILLING CONTROL BOX Figure 1 - Lubrication and Servicing Components (LFS and HEV)

5 / JL WIPER POST 2. MITER BOX 3. BRAKE PEDAL 4. ACCELERATOR PEDAL 5. WINDSHIELD WASHER RESERVOIR 6. INTERMEDIATE STEERING SHAFT 7. STEERING SHAFT 8. BATTERY TERMINALS 9. BATTERY TRAY GUIDE RAIL. DOOR RODS AND LEVER 11. FRONT ACCESS RAMP (OPTIONAL) 12. STEERING GEARBOX 13. AUTOMATIC GREASING RESERVOIR 14. DRAG LINK END 15. STEERING KNUCKLES. WHEEL BEARING 17. TIE ROD END 18. REAR ACCESS RAMP (OPTIONAL) 19. DIFFERENTIAL 20. DRIVESHAFT UNIVERSAL JOINT 21. DRIVESHAFT SLIDING JOINT 22. TRANSMISSION/DRIVE DIPSTICK 23. TRANSMISSION/DRIVE OIL FILTER 24. FUEL FILTER 25. TRANSMISSION/DRIVE OIL PAN 26. RADIATOR 27. ENGINE OIL FILTER FILTER 28. ENGINE COOLANT FILTER 29. ENGINE DIPSTICK 30. COOLANT SURGE TANK 31. HYDRAULIC RESERVOIR 32. A/C COMPRESSOR (OPTIONAL) 33. COOLANT FILLING CONTROL BOX 34. ARTICULATION PIVOT Figure 1 - Lubrication and Servicing Components (Artic)

6 2009JL07 6 / BLANK PAGE

7 SECTION A MAINTENANCE SCHEDULE (ZF) / JL07 MAINTENANCE SCHEDULE This schedule applies to all vehicles equipped with ZF axles with disk brakes, a Cummins ISC or ISL03/05/06 engine and a ZF transmission. According to the model of your vehicle, see Figures 1 or 2 in the general section for the item numbers indicated in the chart. NOTE: If the vehicle is equipped with an automatic greasing system, lubrication of the items marked with an asterisk (*) in the maintenance schedule is managed by this system. See section : CENTRAL LUBRICATION for more details. ON RECEIPT OF VEHICLE ITEM Change the oil and filter in all systems. DAILY INSPECTION OR AS REQUIRED OUTSIDE THE VEHICLE ITEM Check for leaks under vehicle and in engine compartment. Check that all doors close properly, lubricate as required. Drain accumulated water in air tanks. 5 Check windshield washer fluid level and add if necessary. ENGINE COMPARTMENT ITEM 22 Check transmission fluid level, adjust if necessary. 24 Drain accumulated water in fuel filter/water separator. 29 Check engine oil level, adjust if necessary. Check coolant fluid level and adjust if necessary. 31 Check hydraulic reservoir fluid level at sight glass. INSIDE THE VEHICLE ITEM 1 Verify proper operation of windshield wiper/washer. 11, 18 Deploy the ramp and check for proper operation.

8 2009JL07 8 / EVERY 6,000 MI (,000 KM) ITEM LUBRICANT REAR AXLE - SECTION Check the differential oil level. Correct if necessary. See manufacturer s documentation STEERING MECHANISM - SECTION 07 Inspect all fluid lines and connections for leaks. * 2 Lubricate the miter box upper bearing. Mobil Mobilith SHC PM * 14 Lubricate the drag link ends. Lithium-based grease * 15 Lubricate the steering knuckles. Saponified lithium mineral oil-based multigrade grease of the NLGI class 2 * 17 Lubricate the tie rod ends. Lithium-based grease ENGINE - SECTION 09 Check for oil leaks at air compressor oil lines. Inspect all fluid lines and connections for leaks. 26 Inspect the radiator for leaks 27 Change engine oil and oil filter. SAE 15W-40 (CG-4SF or CF-4SFw) DRIVESHAFT - SECTION 20, 21 Lubricate universal joints, slip yoke and splines according to the manufacturer s procedure. BATTERIES - SECTION 8 Clean with sodium bicarbonate and inspect. NLGI grade 2, lithium 12-hydroxy stereate with molybdenum disulfide grease for universal joints (Meritor specification O-634-B). See the manufacturer s documentation for approved lubricants. EVERY,000 MI (20,000 KM) ITEM LUBRICANT PNEUMATIC SYSTEM - SECTION 08 Lubricate the kneeling system linkage. Lubriplate 3 Lubricate the brake pedal pivots. Lubriplate ENGINE - SECTION 09 4 Lubricate the accelerator pedal pivots. Lubriplate 24 Replace fuel filter. 28, 30 Test coolant solution and replace filter. TRANSMISSION - SECTION 23 Change Dexron-III oil and filter Transynd: see 25,000 mi (40,000 km). Ecofluid A Plus: see 0,000 mi (150,000 km). Other type: see manufacturer s documentation. REAR ACCESS RAMP (opt.) - SECTION Lubricate all the bearings. Low Temperature Grease HEATING AND VENTILATION - SECTION 14 Check refrigerant level.

FLUIDS AND LUBRICANTS

FLUIDS AND LUBRICANTS SECTION 19-401.03 19-401.03/ 1 2011MR14 IMPORTANT THIS VEHICLE MUST ONLY BE FUELED WITH ULTRA LOW-SULFUR DIESEL FUEL IMPORTANT NOTICE The following information is a summary of the standards, recommendations

More information

DISTANCE TRAVELED 1 (miles/km) LUBRICANT &/OR PART 2. LUBRICATION AND SERVICING SCHEDULE Item. Months

DISTANCE TRAVELED 1 (miles/km) LUBRICANT &/OR PART 2. LUBRICATION AND SERVICING SCHEDULE Item. Months GENERAL Flexible hoses, thoroughly inspect all hoses - 12 ------- Front discharge tube, qty:2, check to see if clogged 3-3 ------- 01 ENGINE Air cleaner, inspect, clean, replace element if required 27

More information

TECHNICAL MANUAL ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST) FOR

TECHNICAL MANUAL ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST) FOR TM 5-4210-227-24&P-5 TECHNICAL MANUAL ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST) FOR 85' AERIAL LADDER FIRE FIGHTING TRUCK NSN

More information

SAMLUBE GEAR MAX RANGE EP 90; EP 80W90 & EP 85W140 (GL4)

SAMLUBE GEAR MAX RANGE EP 90; EP 80W90 & EP 85W140 (GL4) GEAR OILS SAMLUBE GEAR MAX RANGE EP 90; EP 80W90 & EP 85W140 (GL4) High performance mild extreme pressure gear lubricant, containing multi-functional additives required for mild extreme pressure conditions.

More information

SRT OPERATIONS MANUAL

SRT OPERATIONS MANUAL MAINTENANCE SECTION PAGE # VEHICLE DAILY INSPECTION.......................................1 P.M. INSPECTION #1.................................................3 P.M. INSPECTION #2.................................................6

More information

LUBRICATION CONTENTS

LUBRICATION CONTENTS CHRYSLER SERVICE MANUAL LUBRICATION-403 Section XV LUBRICATION CONTENTS Page Engine Oil Recommendations 403 Engine Oil Change Periods 405 Lubrication Recommendations 406 1. ENGINE OIL RECOMMENDATIONS (FIG.

More information

Maintenance. Lubricants and Fluids Maintenance Minder General Information... Maintenance Main Items... Maintenance Sub Items...

Maintenance. Lubricants and Fluids Maintenance Minder General Information... Maintenance Main Items... Maintenance Sub Items... Maintenance Lubricants and Fluids... 3-2 Maintenance Minder General Information.... 3-4 Maintenance Main Items.... 3-7 Maintenance Sub Items.... 3-8 Lubricants and Fluids For details of the lubrication

More information

SECTION steering mechanism

SECTION steering mechanism 07-302.01/ 1 2011MR17 SECTION 07-302.01 GENERAL Description See Figure 1. The includes the steering wheel (1), the steering column, the miter box (3), the steering shafts (2 and 4), and the drag link (7).

More information

SECTION ZF FRONT AXLE

SECTION ZF FRONT AXLE 04-101.01/ 1 2011JA14 SECTION 04-101.01 6 3 5 1 2 9 1. Upper radius rod 2. Lower radius rod 3. Caliper 4. BRAKE Disk 5. Pneumatic connector 6. Hub 7. steering knuckle 8. Grease Fitting 9. Pneumatic connector

More information

LUBRICATION ORDER LO

LUBRICATION ORDER LO LUBRICATION ORDER LO 9-2320-289-12 1 May 1992 (Supersedes LO 9-2320-289-12, dated 16 June 1986) TRUCK, CARGO, TACTICAL, 1-1/4 TON, 4X4, M1008 (2320-01-123-6827) TRUCK, CARGO, TACTICAL, 1-1/4 TON, 4X4,

More information

CONTENTS 01 GASOLINE ENGINE OILS 02 DIESEL ENGINE OILS 04 AUTOMOTIVE FLUIDS 05 AUTOMOTIVE GREASES

CONTENTS 01 GASOLINE ENGINE OILS 02 DIESEL ENGINE OILS 04 AUTOMOTIVE FLUIDS 05 AUTOMOTIVE GREASES CONTENTS 01 GASOLINE ENGINE OILS 02 DIESEL ENGINE OILS...... 2 10 0 3 M A N U A L A U T O M O T I V E G E A R O I L S... 1 7 04 AUTOMOTIVE FLUIDS... 05 AUTOMOTIVE GREASES... 6 Oraby Street, El Tawfikeya

More information

Aerial Maintenance. Drip less oil or light machine oil is used on control cables, door latches, and hinges.

Aerial Maintenance. Drip less oil or light machine oil is used on control cables, door latches, and hinges. Oils, greases, and other lubricants used by this Department. Engine oil SAE 15W40 is used in the crankcase of our apparatus, high-fog pump, 1981 American La France road pump transmission and also as a

More information

Lubricants & speciality products for commercial vehicles

Lubricants & speciality products for commercial vehicles Lubricants & speciality products for commercial vehicles Yet to be replaced with the HiRes version or approved pic Engine oils Chevron Global Lubricants scientists and engineers work closely with OEMs

More information

Unit D: Agricultural Equipment Systems. Lesson 1: Understanding Applications of Fluids and Lubricants in Agricultural Equipment

Unit D: Agricultural Equipment Systems. Lesson 1: Understanding Applications of Fluids and Lubricants in Agricultural Equipment Unit D: Agricultural Equipment Systems Lesson 1: Understanding Applications of Fluids and Lubricants in Agricultural Equipment 1 Terms Ash content bottom dead center cloud point compression ratio coolant

More information

Marine Range.

Marine Range. Marine Range www.motul.com ADVICE Why do Marine engines require specific lubricants? Marine engines are used in very different conditions from that of automotive engines. They are also operating at much

More information

$2.50. Lubrication. Maintenance Manual No. 1 Revised 3-99

$2.50. Lubrication. Maintenance Manual No. 1 Revised 3-99 $2.50 Lubrication Maintenance Manual No. 1 Revised 3-99 Service Notes This manual contains Meritor s grease and oil lubricant specifications, lubrication procedures and intervals, and product capacities.

More information

Lubricant Viscosities

Lubricant Viscosities Page 1 of 5 Shutdown SIS Previous Screen Product: TRUCK Model: 793C TRUCK ATY Configuration: 793C Off-Highway Truck ATY00001-UP (MACHINE) POWERED BY 3516 Engine Operation and Maintenance Manual 793C Off-Highway

More information

1.1 Unless otherwise stated, the specification references and test methods are from the latest version in effect at the time of this contract.

1.1 Unless otherwise stated, the specification references and test methods are from the latest version in effect at the time of this contract. (Page 1 of 6) LUBRICATING PRODUCTS MGS-92-12K 1.0 DESCRIPTION. This specification covers motor vehicle lubricating products for delivery in prepackaged containers such as drums, pails, etc., or for delivery

More information

Railway Crane Maintenance Manual

Railway Crane Maintenance Manual Diesel Engine System 2.4 2.4.1 Diesel Engine 2.4.1.1 Diesel Engine (Different Types) 2.4.1.2 Diesel Engine (Crane wise list) 2.4.2 Exhaust System 2.4.3 Fuel System 2.4.4 Diesel Engine Accelerator 2.4.5

More information

Factory Approved Service Products November 2001

Factory Approved Service Products November 2001 Factory Approved Service Products November 2001 Mercedes-Benz USA recommends the use of Mercedes-Benz original parts, replacement parts, accessories as well as factory approved service products explicitly

More information

SECTION ZF AV-132 REAR AXLE

SECTION ZF AV-132 REAR AXLE 05-101.02/ 1 2010SE29 SECTION 05-101.02 GENERAL DESCRIPTION The rear axle is an AV-132 ZF model equipped with a pneumatic disc brakes system. An identification plate is affixed to the right rear side of

More information

LUBRICATION AND MAINTENANCE

LUBRICATION AND MAINTENANCE DN LUBRICATION AND MAINTENANCE 0-1 LUBRICATION AND MAINTENANCE TABLE OF CONTENTS LUBRICANTS... 1 MAINTENANCE SCHEDULES... 3 JUMP STARTING, TOWING AND HOISTING... 8 LUBRICANTS TABLE OF CONTENTS SERVICE

More information

26-LU-L BRACKET-CARRIAGE AND EQUIPMENT, PART NO

26-LU-L BRACKET-CARRIAGE AND EQUIPMENT, PART NO 26-LU-L BRACKET-CARRIAGE AND EQUIPMENT, PART NO. 655031 OCTOBER, 2006 NOTE: The following description and operation is based on this device and its components being new or this device and its components

More information

Section XV LUBRICATION

Section XV LUBRICATION Section XV LUBRICATION SERVICE BULLETIN REFERENCE NUMBER DATE SUBJECT CHANGES CHRYSLER SERVICE MANUAL LUBRICATION 605 Section XV LUBRICATION 1. ENGINE OIL RECOMMENDATIONS The use of a good quality engine

More information

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B 22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6

More information

FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO

FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO DELO DELIVERS CONFIDENCE TABLE OF CONTENTS Introduction 3 Engine Oils 4-5 Transmission Fluids 6 Gear Lubricants 7 Greases 8 Coolant/Antifreeze

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

Installation, Operating and Maintenance Instructions. Rotating Machine Screw Actuators. With Parts List Publication Part No.

Installation, Operating and Maintenance Instructions. Rotating Machine Screw Actuators. With Parts List Publication Part No. Installation, Operating and Maintenance Instructions With Parts List Publication Part No. SK-2389-R1 Rotating Machine Screw Actuators 1/4 Through 1-Ton Capacity Caution This manual contains important information

More information

(a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed between the two halves.

(a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed between the two halves. Manual AWBCMM0001-7.2/USA Section 300 External Design (2) Wheels Stored Without Tires Installed (a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed

More information

Hydraulic Hand Crimping Tool, PN

Hydraulic Hand Crimping Tool, PN Hydraulic Hand Crimping Tool, PN 59974-1 Instruction Sheet 408-6757 19 JUN 17 Rev G PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand

More information

TC Series Cooling Systems

TC Series Cooling Systems TC Series Cooling Systems Table of Contents Table of Contents...1 List of Figures...1 Safety...2 Introduction...2 General Specifications...2 Types of Coolant...2 Routine Maintenance...2 Surge Tank Coolant

More information

Light condition and operation Windshield glass condition Wiper blade condition Paint condition and corrosion Fluid leaks Door and hood lock condition

Light condition and operation Windshield glass condition Wiper blade condition Paint condition and corrosion Fluid leaks Door and hood lock condition GENERAL CHECKS Engine Compartment The following should be checked regularly: Engine oil level and condition Transmission fluid level and condition Brake fluid level Clutch fluid level Engine coolant level

More information

SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type

SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS Specifications........................ 3A-1 General Specifications.................. 3A-1 Fastener Tightening Specifications......... 3A-2 Component Locator...................

More information

ENGINE OIL RECOMMENDATIONS

ENGINE OIL RECOMMENDATIONS LUBRICATION 404 CHRYSLER SERVICE MANUAL 10,000 MILES 5,000 MILES 1 j j 15,,000 MILES 1,000 MILES III 20,000 MILES UPPER AND LOWER BALL JOINTS 4 fittings CL K E Y TO L U B R I C A N T S CL Chassis Lubricant

More information

SECTION 6 1 SERVICE PROCEDURES AND SPECIFICATIONS. Introduction

SECTION 6 1 SERVICE PROCEDURES AND SPECIFICATIONS. Introduction SERVICE PROCEDURES AND SPECIFICATIONS Introduction SECTION 6 1 Vehicle identification...................................... 156 Engine compartment overview............................. 157 Do-it-yourself

More information

~ HONDA CB1000C IIOIL PUMP. rw_u LUBRICATION ENGINE LUBRICATION DIAGRAM. Date of Issue: Sept., 1982 HONDA MOTOR CO., ltd.

~ HONDA CB1000C IIOIL PUMP. rw_u LUBRICATION ENGINE LUBRICATION DIAGRAM. Date of Issue: Sept., 1982 HONDA MOTOR CO., ltd. LUBRICATION ENGINE LUBRICATION DIAGRAM EXHAUST CAMSHAFT ~ HONDA CB1000C INTAKE CAMSHAFT,t Oil FilTER Oil COOLER PRIMARY CHAIN TENSIONER IIOIL PUMP PRIMARY SHAFT TRANSMISSION MAINSHAFT 01 COUNTERSHAFT Oil

More information

LUBRICATION AND MAINTENANCE

LUBRICATION AND MAINTENANCE WJ LUBRICATION AND MAINTENANCE 0-1 LUBRICATION AND MAINTENANCE TABLE OF CONTENTS LUBRICANTS... 1 MAINTENANCE SCHEDULES... 4 JUMP STARTING, HOISTING AND TOWING... 9 LUBRICANTS TABLE OF CONTENTS SERVICE

More information

PONTIAC 2000 MILE LUBRICATION CHART

PONTIAC 2000 MILE LUBRICATION CHART 0-0 1955 PONTIAC SHOP MANUAL PONTIAC 2000 MILE LUBRICATION CHART LOWER CONTROL ARM PIVOT SHAFT 'FRONT WHEEL BEARINGS (See pageo-4) STEERING IDLER ARM STEERING CONNECTtNG ROD TIE ROD ENDS UPPER CONTROL

More information

GREASES AEROSHELL GREASES

GREASES AEROSHELL GREASES GREASES AEROSHELL GREASES THE DEFINITION OF A GREASE IS: "A solid or semi-solid lubricant comprising a dispersion of a thickening agent in a liquid lubricant to which various additives have been added

More information

High Lift Transmission Jack

High Lift Transmission Jack 655 Eisenhower Drive Owatonna, MN 55060-0995 USA Phone: (507) 455-7000 Tech. Serv.: (800) 533-6127 Fax: (800) 955-8329 Order Entry: (800) 533-6127 Fax: (800) 283-8665 International Sales: (507) 455-7223

More information

Section 7 REAR END MAINTENANCE AND REPAIR

Section 7 REAR END MAINTENANCE AND REPAIR TABLE OF CONTENTS PAGE INTRODUCTION...7-2 MAINTENANCE AND LUBRICANT...7-3 DEFINITION OF VIEW POINTS...7-3 DATA PLATE...7-3 MAINTENANCE POINTS...7-4 MAINTENANCE INTERVALS...7-5 ADJUSTMENT AND CHECKS...7-5

More information

CAM2

CAM2 www.cam2.com 1-800-338-CAM2 1 2 What Does Motor Oil do for Your Engine? 4 What is in your CAM2 motor oil? 4 Why You Change Your Motor Oil 5 Selecting the Right Motor Oil for Your Vehicle 6 Viscosity 6

More information

Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd

Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd 23-2 AUTOMATIC TRANSMISSION General Information/ Service Specifications GENERAL INFORMATION 23100010141 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R4AW2-6 V4AW2-6 Type

More information

2-135, & Chassis & Engine Chassis Only Volume 1 of 2

2-135, & Chassis & Engine Chassis Only Volume 1 of 2 White Service Manual 2-135, 2-155 & 2-180 Chassis & Engine 4-210 Chassis Only Volume 1 of 2 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF WHITE OR IT S SUCCESSORS.

More information

Roadranger Products. Lubrication Manual TCMT0021

Roadranger Products. Lubrication Manual TCMT0021 Roadranger Products Lubrication Manual TCMT0021 June 2008 Table of Contents General Information...1 Introduction to Manual...2 Transmission Lubricants...4 Transmission Lubricant Capacities...6 Drive Axle

More information

Asset Maintenance Policy

Asset Maintenance Policy Asset Maintenance Policy Grantees are required to maintain project equipment at a high level of cleanliness, safety, and mechanical soundness. At a minimum, grantees will perform maintenance according

More information

This product guide will be your reference to the high quality range of lubricants available in Misr Petroleum Co.

This product guide will be your reference to the high quality range of lubricants available in Misr Petroleum Co. Misr Petroleum Co. is a major manufacturing and marketing company in Egypt. We manufacture and market a wide range of lubricants such as automotive, industrial and greases. These lubricants are blended

More information

DEAD ENGINE FIXTURE PORTION

DEAD ENGINE FIXTURE PORTION V 4243-1 Operation & Maintance Information DEAD ENGINE FIXTURE PORTION "U-1-65-8" Dead Engine Fixture, PART NO. 653968 "U-1-40-8" Dead Engine Fixture, PART NO. 569299 AUGUST, 2000 Supersedes issue dated

More information

Current. Installation Instructions

Current. Installation Instructions by Trike Conversion Kit 2004 - Current Harley-Davidson Sportster Installation Instructions REVISED 4-2017 California Sidecar Parts & Technical Support 434.263.8866 Table of contents: 1. Warnings and Considerations

More information

OILS & LUBRICANTS EFFECTIVE SEP 2O13 NO MATTER WHAT BRAND OF TRUCK OR 4WD, WE VE GOT IT COVERED.

OILS & LUBRICANTS EFFECTIVE SEP 2O13 NO MATTER WHAT BRAND OF TRUCK OR 4WD, WE VE GOT IT COVERED. OILS & LUBRICANTS EFFECTIVE SEP 2O13 NO MATTER WHAT BRAND OF TRUCK OR 4WD, WE VE GOT IT COVERED. ENGINE OIL DIESEL GOLD ENGINE OIL A high performance diesel engine lubricant designed to meet the requirements

More information

NISSAN CUSTOMER CARE PROGRAM

NISSAN CUSTOMER CARE PROGRAM NISSAN CUSTOMER CARE PROGRAM NISSAN CARES... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary

More information

* * * * 8 Maintenance Plan 10.1,10.2, ,4 7.1/7.2/7.3

* * * * 8 Maintenance Plan 10.1,10.2, ,4 7.1/7.2/7.3 Maintenance 8 Maintenance Plan * * * * * GB 10.1,10.2,10.3 6.1 12.2 12.1 11.2 12.1 7,4 7.1/7.2/7.3 1.1/1.2/1.3 3.1/3.2/3.3/3.4/4.1/11.1 5.1 5.2 4.2 5.1 5.2 2.1/2.2/2.3/2.4/2.5/2.6/4.1 Item Designation

More information

Service Manual. MF1085 Diesel

Service Manual. MF1085 Diesel Massey Harris Massey Ferguson Service Manual MF1085 Diesel Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF MASSEY HARRIS MASSEY FERGUSON OR IT S SUCCESSORS. MASSEY

More information

Updates to Maintenance Manual MM-0409 (Revised 02-11): Wheel-End Components/Meritor Conventional and Unitized Wheel Ends

Updates to Maintenance Manual MM-0409 (Revised 02-11): Wheel-End Components/Meritor Conventional and Unitized Wheel Ends Technical Bulletin Issued 02-11 Updates to Maintenance Manual MM-0409 (Revised 02-11): Wheel-End Components/Meritor Conventional and Unitized Wheel Ends Issued 1 Technical 02-11 Bulletin Hazard Alert Messages

More information

Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair

Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair HMM180001 Brake System H1.5-1.8TX, H2.0TXS [B475]; H2.5-3.5TX [B466] Safety Precautions Maintenance and Repair When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened,

More information

CLEANERS AND DEGREASERS LUBRICANTS

CLEANERS AND DEGREASERS LUBRICANTS CLEANERS AND DEGREASERS ENGINE CLEANER AND DEGREASER Solvent-based formula Quickly dissolves grease, oil and tar from engines and equipment Spray on, rinse off with water SP4220 20 oz. can Net wt. 14.5

More information

Fuller Mid-Range Transmissions TRDR0100

Fuller Mid-Range Transmissions TRDR0100 Driver Instructions Video Instruction Available Instructional videos are available for download at no charge at roadranger.com Videos are also available for purchase. To order, call 1-888-386-4636. Ask

More information

Service/Inspection Checklist and Report

Service/Inspection Checklist and Report Fastrac 2155 and 2170 Service/Inspection Checklist and Report Fastrac 2155 and 2170 Issued by JCB Technical Publications, JCB Service, World Parts Centre, Beamhurst, Uttoxeter, Staffordshire, ST14 5PA,

More information

Warranty Booklet. Page 1 of 42

Warranty Booklet. Page 1 of 42 Warranty Booklet Page 1 of 42 Contents Our Company... 3 To Users... 4 Higer Bus Warranty Terms... 6 Periodical Maintenance Regulation... 12 Appendix 1 Oil, Fluid and Grease... 36 Appendix 2 Vehicle Information

More information

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS TYPE OF INSPECTION UNDER THE HOOD GASOLINE AND DIESEL 1 Fuel, oil, exhaust leaks - inspect 2 Oil and fuel lines inspect for kinks and wear 3 Automatic transmission

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

WARNING. 4. The wearing of safety glasses, footwear and personal safety clothing is compulsory.

WARNING. 4. The wearing of safety glasses, footwear and personal safety clothing is compulsory. SECTION 18-500.00 18-500.00/ 1 WARNING 1. All Federal, State, Provincial, Municipal and company, (including Transit Authority), laws and regulations regarding vehicles must be complied with. Also, any

More information

HYDRAULIC SYSTEM, ISL-07

HYDRAULIC SYSTEM, ISL-07 SECTION 09-304.295 09-304.295/ 1 GENERAL DESCRIPTION 7 1 This system uses hydraulic power to operate a fan that forces outside air into the radiator located on the left-hand side at the rear of the bus.

More information

DRIVE AXLES. Differentials & Axle Shafts - Corvette

DRIVE AXLES. Differentials & Axle Shafts - Corvette DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case

More information

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications SERVICE PROCEDURES AND SPECIFICATIONS Engine SECTION 6 2 Specifications........................................... 162 Fuel.................................................... 164 Facts about engine oil

More information

BRAKE SYSTEM Return To Main Table of Contents

BRAKE SYSTEM Return To Main Table of Contents BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...

More information

PENNZOIL 100% SYNTHETIC MULTI-VEHICLE ATF

PENNZOIL 100% SYNTHETIC MULTI-VEHICLE ATF PENNZOIL 100% SYNTHETIC MULTI-VEHICLE ATF Pennzoil 100% Synthetic Multi-Vehicle ATF is the latest formulation and advanced technology which meets specification requirement of North America, Japanese and

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: September 2009

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: September 2009 NUMBER: 9 1 09 S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: September 2009 SUBJECT: ENGINE OIL AND FILTER CHANGING ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title

More information

Trailer Axle Hub Replacement SERVICE MANUAL

Trailer Axle Hub Replacement SERVICE MANUAL Trailer Axle Hub Replacement SERVICE MANUAL TABLE OF CONTENTS Safety Information 2 Hub Removal 2 Brake Drum Inspection 5 Bearing Inspection 6 Bearing Lubrication - Oil 7 Brake/Idler Hub Installation 8

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 11 01-14 1 11 01-14 SUBJECT DATE DD15 and DD16 Cylinder Head November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DDC-SVC-MAN-0181 DDC-SVC-MAN-S181

More information

Maintenance and Lubrication

Maintenance and Lubrication Maintenance and Lubrication Proper maintenance is necessary to ensure safe, trouble free operation. Inspecting the lift for any wear, damage or other abnormal conditions should be a part of the transit

More information

FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO

FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO FOR COMMERCIAL ON-HIGHWAY HEAVY-DUTY PROTECTION CHOOSE DELO DELO DELIVERS CONFIDENCE TABLE OF CONTENTS Introduction 3 Engine Oils 4-5 Transmission Fluids 6 Gear Lubricants 7 Greases 8 Coolant/Antifreeze

More information

Cooling System. Table of Contents

Cooling System. Table of Contents Sub-Headings Safety 2 s 2 Cautions 2 Notes 2 Introduction 2 General Specifications 2 Engine 2 Coolant 2 Routine Maintenance 2 Hose Connections 4 Radiator, Charge Air and Heater Cores 4 Cooling System Leaks

More information

LUBRICATION AND MAINTENANCE CHART

LUBRICATION AND MAINTENANCE CHART LUBRICATION AND MAINTENANCE 0-1 LUBRICATION AND MAINTENANCE CHART PSF EO Power Steering Reservoir (Check Level) 4,000 Engine Oil (Change) 4,000 Engine Oil Filter Element (Replace) 4,000 HTF Brake Master

More information

Steering and Suspension

Steering and Suspension The Steering and Suspension system is engineered to allow the vehicle to turn and absorb road irregularities. The suspension is comprised of springs, suspension arms or links and shock dampers. These components

More information

Hillman Minx Maintenance Schedule

Hillman Minx Maintenance Schedule Hillman Minx Maintenance Schedule The maintenance schedule for most Series Minxes can be found as a large fold-out sheet, pasted inside the back cover of the Owner's Handbook. Series V and VI have a much

More information

1. Recommended Materials

1. Recommended Materials 1. Recommended Materials A: 1. GENERAL To insure the best performance, always use the specified oil, gasoline, adhesive, sealant, etc. or a substitute of equivalent quality. 2. FUEL Always use a gasoline

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final

More information

OPERATING INSTRUCTIONS INDEPENDENT WHEEL SUSPENSION RL 75 E/EC FRONT AXLE/TAG AXLE RL 75 A

OPERATING INSTRUCTIONS INDEPENDENT WHEEL SUSPENSION RL 75 E/EC FRONT AXLE/TAG AXLE RL 75 A INDEPENDENT WHEEL SUSPENSION RL 75 E/EC FRONT AXLE/TAG AXLE RL 75 A 587.97.90 en Preface This documentation has been developed for specialized staff trained by ZF Friedrichshafen AG for repair and maintenance

More information

CLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly.

CLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly. CLUTCH CONTENTS -GROUP 6 Page CLUTCH HOUSING ALIGNMENT... 6 CLUTCH PEDAL FREE PLAY 1 CLUTCH RELEASE BEARING 5 CLUTCH RELEASE FORK... 5 CLUTCH SERVICING 2 PILOT BUSHING CRANKSHAFT TO TRANSMISSION DRIVE

More information

SECTION 5 MAINTENANCE

SECTION 5 MAINTENANCE SECTION 5 Maintenance requirements................................ 166 General maintenance..................................... 167 Does your vehicle need repairing?......................... 170 Scheduled

More information

Part 7 DO IT YOURSELF MAINTENANCE

Part 7 DO IT YOURSELF MAINTENANCE Part 7 DO IT YOURSELF MAINTENANCE Chapter 7 2 Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking brake fluid Checking power steering fluid Checking tire pressure

More information

Hubs/Drums/Bearings. Hubs/Drums/Bearings ! CAUTION. Hub Removal. Brake Drum Inspection

Hubs/Drums/Bearings. Hubs/Drums/Bearings ! CAUTION. Hub Removal. Brake Drum Inspection Hub Removal Whenever the hub equipment on your axle must be removed for inspection or maintenance the following procedure should be utilized. 1. Elevate and support the trailer unit per manufacturers instructions.!

More information

BRAKE E

BRAKE E 8-1 GENERAL...8-2 SPECIFICATIONS...8-6 COMPONENTS...8-7 FRONT BRAKE...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn1, Cu2 3 TON SERIES)...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn2 3 TON SERIES)...8-17 BRAKE

More information

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing

More information

SECTION 6 1 SERVICE PROCEDURES AND SPECIFICATIONS. Introduction

SECTION 6 1 SERVICE PROCEDURES AND SPECIFICATIONS. Introduction SERVICE PROCEDURES AND SPECIFICATIONS Introduction SECTION 6 1 Vehicle identification...................................... 192 Engine compartment overview............................. 193 Do it yourself

More information

SECTION 1 LUBRICATION

SECTION 1 LUBRICATION SECTION 1 LUBRICATION Model M2500 OMPS1 M2500 10-2002 Avoid injury! Bring all crane functions to complete stop and turn off engine before lubricating crane. If necessary, spot grease fittings at access

More information

SECTION 7 1 DO IT YOURSELF MAINTENANCE MR2 U. Introduction

SECTION 7 1 DO IT YOURSELF MAINTENANCE MR2 U. Introduction SECTION 7 1 DO IT YOURSELF MAINTENANCE Introduction Engine compartment overview............................... 160 Trunk room overview........................................ 161 Fuse locations.............................................

More information

SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer

SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer Page 1 Allied Form #80-930 Rev 07/2009 SERVICE MANUAL LOG STACKER DA202 DRIVE AXLE TABLE OF CONTENTS PROCEDURE FOR

More information

PROPELLER SHAFT Click on the applicable bookmark to selected the required model year.

PROPELLER SHAFT Click on the applicable bookmark to selected the required model year. PROPELLER SHAFT Click on the applicable bookmark to selected the required model year. Purchased from 25-1 PROPELLER SHAFT CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 SPECIAL TOOL... 2

More information

2010 Toyota Prius Repair Manual

2010 Toyota Prius Repair Manual REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,

More information

Chapter 3 Lubrication

Chapter 3 Lubrication Chapter 3 Lubrication Avoid injury! Bring all crane functions to complete stop and turn engine OFF before lubricating crane. If necessary, spot grease fittings at access points, then stop engine. Attach

More information

HINO PREMIUM PROTECTION

HINO PREMIUM PROTECTION 12 MONTHS MAINTENANCE COVERAGE COE WITH AISIN TRANSMISSION (FROM 12MY) 5,000 km or 3 months Retorque leaf spring u-bolts Adjust brake pedal travel 10,000 km or 6 months Check steering wheel play Check

More information

MANUAL TRANSMISSION CONTENTS

MANUAL TRANSMISSION CONTENTS 22-1 MANUAL TRANSMISSION CONTENTS 22109000319 LUBRICANT... 2 SPECIAL TOOLS... 2 ON-VEHICLE SERVICE... 3 Transmission Oil Check... 3 Transmission Oil Replacement... 3 TRANSMISSION CONTROL*... 4 TRANSMISSION

More information

Lubricant Service Designations for Automotive Manual Transmissions, Manual Transaxles, and Axles

Lubricant Service Designations for Automotive Manual Transmissions, Manual Transaxles, and Axles Lubricant Service Designations for Automotive Manual Transmissions, Manual Transaxles, and Axles API PUBLICATION 1560 EIGHTH EDITION, 2012 SPECIAL NOTES 1. API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS

More information

GENERAL INFORMATION 1 B MAINTENANCE

GENERAL INFORMATION 1 B MAINTENANCE GENERAL INFORMATION 1 B MAINTENANCE Table of Contents Page Maintenance Schedules................... 1B-1 Maintenance Intervals.................. 1B-1 Scheduled Maintenance That Can Be Performed By Owner/Operator.........

More information

HINO PREMIUM PROTECTION

HINO PREMIUM PROTECTION 12 MONTHS MAINTENANCE COVERAGE COE WITH AISIN TRANSMISSION (FROM 12MY) 5,000 km or 3 months Retorque leaf spring u-bolts Adjust brake pedal travel Labour code: COE0005 = 0.8hrs Warranty code: COE0005 10,000

More information

Section 3.1. Machine Maintenance - Machine Maintenance Information. Important Preventive Maintenance Information: Maintenance Charts & Diagrams:

Section 3.1. Machine Maintenance - Machine Maintenance Information. Important Preventive Maintenance Information: Maintenance Charts & Diagrams: Section 3.1 Machine Maintenance - Maintenance Charts & Diagrams: Special Component Break-In Chart... 3.1.2 Preventive Maintenance Schedule Chart... 3.1.2 Lubrication Points Diagram... 3.1.3 Lubricant &

More information

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:

More information

4 qts 4 qts 6 qts. 10 qts 12.5 qts. 7.2 pints 9 pints. 3.5 pints. 2.2 pints. 2.5 pints 3.13 pints 3.13 pints

4 qts 4 qts 6 qts. 10 qts 12.5 qts. 7.2 pints 9 pints. 3.5 pints. 2.2 pints. 2.5 pints 3.13 pints 3.13 pints Recommended lubricants and fluids Automatic transmission fluid AW-4 transmission. 727 and 999 transmissions...... Manual transmission lubricant. The fluid type should be indicated on the dipstick Differential

More information