SCRUBBER. Operating Instructions FLXSP3 FLXSP3T FLX3T. Read these instructions before using the machine IPX /19/03

Transcription

1 SCRUBBER Operating Instructions MODELS: FLX3 FLX3T FLXSP3 FLXSP3T IPX4 Read these instructions before using the machine D /19/03

2 MACHINE DATA LOG/OVERVIEW MODEL DATE OF PURCHASE SERIAL NUMBER SALES REPRESENTATIVE # DEALER NAME OPERATIONS GUIDE NUMBER PUBLISHED Copyright 2003 Windsor Industries, Printed in USA YOUR DEALER Name: Address: Phone Number: OVERVIEW The Flex3 is a revolutionary rider type scrubber with four wheel articulated design for superior maneuverability, simple operation, and low maintenance. The machine design permits access to areas even traditional walk behind machines cannot reach. The squeegee design, location, and steering geometry allows the operator to make tight turns while recovering full width of the scrub path. Controls are logically designed for easy touch button operation, strategically laid out at the operator s fingertips, easily reached from a comfortable seat. In addition, the four wheel stance continues the Windsor concept for operator comfort and stability. The Flex3 was designed from the ground up for ease of maintenance. 2

3 TABLE OF CONTENTS Machine Data Log/Overview...2 Table of Contents...3 HOW TO USE THIS MANUAL How to use this Manual SAFETY Important Safety Instructions Hazard Intensity Level Safety Label Location OPERATIONS Technical Specifications How the Machine Works Components Controls Machine Operation Pre-Run Machine Inspection Starting Machine Filing Machine Scrubbing Double Scrub Emptying & Cleaning Tanks MAINTENANCE Batteries Low-Battery Shut-Down Squeegee Adjustment Adjusting Squeegee Pitch Adjusting Deflection Replace Rear Squeegee Blades Replace Front Squeegee Blades Scrub Head-Disk Scrub Brushes Replacement/Installing Scrub Brushes Scrub Head- Cylindrical Differential Drive Chain Drive Wheel Chain Brakes Tires and Wheels Vacuum Motors Brush Motors Towing or Pushing Machine Jacking Machine Storage Service Schedule Machine Troubleshooting GROUP PARTS LIST Brake Control Panel Decal Differential Electrical Floor Forward/Reverse Pedal Front Bumper Disk Front Bumper - Cylindrical Front Frame Front Wheel Rear Frame Rear Wheel Recovery Tank Scrub Brush/Pad Driver Scrub Head Cylindrical Scrub Head Cyl. Valve & Hopper Scrub Head Disk Scrub Head Lift - Cylindrical Scrub Head Lift - Disk Seat Solution Hoses & Fittings Solution Tank Squeegee - Standard Squeegee - Tight Squeegee Lift Steering Vacuum Wiring Battery Wiring Control Panel Wiring Electrical Panel Wiring Front Frame Wiring Rear Frame Wiring Schematic Suggested Spare Parts EC Declaration of Conformity Notes Warranty FLX /19/03 3

4 HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealer. When placing an order for parts, the machine model and machine serial number is important. Refer to the MACHINE DATA box, which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. MODEL DATE OF PURCHASE SERIAL NUMBER SALES REPRESENTATIVE # DEALER NAME OPERATIONS GUIDE NUMBER PUBLISHED Copyright 2003 Windsor Industries, Printed in USA The model and serial number of your machine are located approximately where indicated. The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards is identified that could result in product or personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order: - Batteries - Squeegee Assembly - Scrub Head - Differential Drive Chain - Drive Wheel Chain - Brakes - Tires and Wheels - Vacuum Motors - Brush Motors - Towing and Pushing Machine - Storage - Service Schedule - Troubleshooting The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information: - REF column refers to the reference number on the parts illustration. - PART NO. column lists the part number for the part. - QTY column lists the quantity of the part used in that area of the machine. - DESCRIPTION column is a brief description of the part. - SERIAL NO. FROM column indicates the first machine the part number is applicable to. When the machine design has changed, this column will indicate serial number of applicable machine. The main illustration shows the most current design of the machine. The boxed illustrations show older designs. If column has an asterisk (*), call manufacturer for serial number. - NOTES column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS that came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The 98# on the lower left corner of the front cover is the part number for this manual. 1-1

5 IMPORTANT SAFETY INSTRUCTIONS When using a battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.! WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer s recommended components and attachments. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is not suitable for picking up hazardous dust. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. Disconnect battery before cleaning or servicing. Before the machine is discarded, the batteries must be removed and properly disposed of. Make sure all warning and caution labels are legible and properly attached to the machine. During operation, attention shall be paid to other persons, especially children. Before use all covers and doors shall be put in the positions specified in the instructions. When leaving unattended, secure against unintentional movement. The machine shall only be operated by instructed and authorized persons. When leaving unattended, switch off or lock the main power switch to prevent unauthorized use. Only chemicals recommended by the manufacturer shall be used. This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other brushes may affect its safety. SAVE THESE INSTRUCTIONS 2-1

6 HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions:! WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.! CAUTION CAUTION - Hazards or unsafe practices, which could result in, minor personal injury or product or property damage. FOR SAFETY: To Identify actions, which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts.! WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep solution tank in raised position when charging. Keep sparks and flames away from the batteries.! WARNING Do not smoke around batteries. Disconnect batteries before working on machine. Only qualified personnel should work inside machine. Always wear eye protection and protective clothing when working on or near batteries.! WARNING Avoid skin contact with the acid contained in the batteries. Never allow metal to lie across battery tops. 2-2

7 SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Flex3 TM. If, at any time, the labels become illegible, promptly replace them. SAFETY DECAL FOR SAFETY BATTERY CAUTION LOCATED ON BACK SIDE OF FRONT BATTERY COMPARTMENT PLATE SAFETY DECAL SAFETY DECAL SUPPORT WARNING LOCATED ON FRAME NEXT TO VACUUM INLET SAFETY DECAL SAFETY DECAL LOCATED ON FRAME NEXT TO DECAL 2-3

8 TECHNICAL SPECIFICATIONS ITEM Rated Voltage Rated Amperage Batteries Scrub Brush Motors Vacuum Motor Propelling Motor Mass (GVW) Weight empty without batteries Solution Control Solution tank capacity Recovery tank capacity Scrub brush diameter for 34 in. (86 cm) disk scrub head Scrub brush diameter for 34 in. (86 cm) cylindrical scrub head Scrub brush length for 34 in. (86 cm) cylindrical scrub head Scrub brush pressure Scrub brush speed (Disk) Scrub brush speed (cyl) Tires Maximum speed Coverage Frame construction Brakes Minimum aisle u-turn width DIMENSION/CAPACITY 36VDC 90 Amps 6 x 6 Volt hr rate 2 x.75 hp (0.56 kw) 2 x.75 hp ( ,000 rpm 2 hp ( rpm, 27A 2102 lbs. (953 kg) 914 lbs. (415 kg) Gravity feed, fully variable with automatic shutoff in neutral 35 gal. (132l) 35 gal. (132l) 17 in (43.0 cm) 6 in (15.2 cm) 32 in. (81.3 cm) lbs. (0-91 kg) 200 rpm 800 rpm 4 x 16 in (40.64 cm) foam filled black knobby standard. 6.2 mile/hour (10k/hr) 49,300 sq. ft/hr (4,590 sq. m/hr) at 3.5 mph (5.6k/hr) with 2 in (5 cm) overlap. Welded cold rolled steel and steel plate with epoxy powder coat finish. Dual self centering mechanical 6 in (15.24 cm) disc with hand lock parking brake. 96 in (243.8 cm) SPECIAL NOTES: The sound pressure level at the operator s ear was measured to be 76 dba. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure level is below 63 dba. The weighted root mean square acceleration at the operator s arms was measured to be below 2.5m/s². this was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measurement and related calculations were made in accordance with ANSI S

9 TECHNICAL SPECIFICATIONS ITEM Height Length with disk head Length with cylindrical head Width with standard squeegee Width with tight squeegee Width w/o squeegee DIMENSION/CAPACITY 44.5 in (113 cm) 95.2 in (241.8 cm) 95.8 in (243.3 cm) 48.7 in (123.7 cm) 43.0 in (109.2 cm) 42.5 in (108.0 cm) SQUEEGEE WIDTH HEAD WIDTH TOP VIEW HEIGHT RIGHT SIDE VIEW LENGTH 3-2

10 HOW THE MACHINE WORKS The Flex3 TM is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system, and operator control system. The function of the solution system is to store cleaning solution and deliver it to the scrub system. The solution system consists of the solution tank, strainers, valve and controls. The solution tank stores cleaning solution (water and detergent) until it is delivered to the scrub system. The strainers protect the valve from debris. The valve is a solenoid type valve, which controls the delivery of cleaning solution to the scrub system. The valve automatically prevents solution flow unless the scrub brushes are turned on and the machine is being propelled. The solution control switch controls the amount of cleaning solution delivered to the scrub system by controlling the amount of time the valve is open. The function of the scrub system is to scrub the floor. The disk scrub systems consists of two rotary type disk scrub brushes, motors, scrub deck skirt, lift actuator and controls. The brushes scrub the floor as the motors drive the brushes. The brush drive hubs allow the scrub brushes to follow irregularities and changes in the floor without loosing contact with the floor. The scrub deck skirts and side squeegees control the cleaning solution on the floor so that the squeegee can pick it up. The one touch switch controls the motors and lift actuator to turn the motors on and lower the deck, or turn the motors off and raise the deck. The brush pressure switch controls the down pressure on the scrub deck. The scrub plus system consists of two cylindrical type brushes, motors, scrub deck skirts, hopper, lift actuator, and controls. The cylindrical scrub head is designed to eliminate debris that may be caught in the squeegee while scrubbing. Water is applied to the first scrubbing brush turning in a clockwise rotation when viewed from the right or operator s side of machine. The first brush scrubs dirt and debris between the brushes. The second scrubbing brush, turning in a counter clockwise rotation, picks up debris and throws it into a removable hopper. The larger debris that might catch under the squeegee is collected in the hopper. Water is allowed to drain out the hopper into the squeegee path where it is recovered from the floor. The scrub deck skirts control the cleaning solution on the floor so that the squeegee can pick it up. The one touch switch controls the motors and lift actuator to turn the motors on and lower the deck, or turn the motors off and raise the deck. The brush pressure switch controls the down pressure on the scrub deck. The function of the recovery system is to vacuum the soiled water back into the recovery tank. The recovery system consists of the squeegee, vacuum motors, filter, recovery tank and controls. The squeegee wipes the dirty solution off the floor as the machine moves forward. The vacuum motors provide suction to draw the dirty solution off the floor and into the recovery tank. The filter protects the vacuum fan from debris and foam. The recovery tank stores the dirty solution. The float switch in the tank activates the recovery tank full indicator, shuts off the scrub motors and solution flow, raises the scrub deck then squeegee, and shuts off vacuum motor. The function of the operator control system is to control the direction and speed of the machine. The directional control system consists of the direction/speed control pedal, steering wheel, brake pedal, propel controller, and drive wheels. The direction/speed pedal signals forward or reverse direction and speed. The controller interprets signals from the direction/speed pedal to command the drive wheel to propel or slow the machine. The steering wheel articulates the machine to travel in the direction desired by the operator. The brake can be used to hold the machine on slopes. 3-3

11 COMPONENTS Control Panel 2. Front Bumper 3. Electrical Cover 4. Solution Tank 5. Solution Tank Cover 6. Recovery Tank 7. Recovery Tank Cover 8. Recovery Tank Drain Hose 9. Recovery Tank Drain Cap 10. Scrub Head 11. Solution Tank Drain Hose 12. Squeegee 13. Vacuum Motors 3-4

12 CONTROLS Key Switch 2. Emergency Stop Button 3. One Touch Switch 4. Brush Pressure Switch 5. Solution Control Switch 6. Vacuum/Squeegee Switch 7. Display Toggle Switch Information Screen 1 Information Screen 2 Hour Meter Fault Codes and Special Icons Battery Meter 8. Recycle Switch (Optional) 9. Recycle Indicator Light (Optional) 10. Headlight Switch (Optional) 11. Brake Pedal 12. Parking Brake Knob 13. Directional Control Pedal and Speed Reduction Feature 14. Horn Button 15. Steering Wheel 16. Steering Wheel Tilt Lever 17. Squeegee Camber Adjustment Knob 18. Squeegee Deflection Adjustment Knob 3-5

13 CONTROLS

14 CONTROLS 1. KEY SWITCH Controls the power for the machine functions. To turn the machine power on, rotate key clockwise. When the key is turned on the battery symbol will flash for 12 seconds while the system runs selfdiagnostics and returns scrub deck and squeegee to raised position, if necessary. The controller will not respond to other commands until this routine is complete. To turn the machine power off, rotate key counterclockwise. INFORMATION DISPLAY 2. EMERGENCY STOP BUTTON This safety feature is designed to cut all power to the machine at any time. To shut the machine power off, push the Emergency Stop switch. To reset the machine, rotate the switch clockwise. INFORMATION DISPLAY 3-7

15 CONTROLS 3. ONE TOUCH SWITCH This switch controls the scrub brushes and vacuum all in one touch. To start scrubbing, press the one touch switch. The brush drive motors will turn on, the scrub deck will lower to the light scrub position, the solution will flow at two bars rate, the squeegee will lower and the vacuum will turn on. The information display window will show which functions are operating. If the direction control pedal is in the neutral position for more than two seconds the brushes and solution flow will stop. If the one touch switch is activated without brushes installed, the brush motors will stop, the scrub deck will rise, and the brush pressure indicator will display error code To stop scrubbing, press the one touch switch. The brush drive motors will turn off, the scrub deck will raise the solution flow will stop, the squeegee will raise after a 15 second delay, and the vacuum motor will turn off. This delay is to clear the vacuum hose of recovered solution. INFORMATION DISPLAY 4. BRUSH PRESSURE SWITCH This switch controls the amount of brush pressure to the floor. There are 5 different pressure settings. To decrease the amount of down pressure, press the top of the brush pressure switch (-). To increase the amount of down pressure, press the bottom of the brush pressure switch (+). The information display screen will show the amount of pressure. NOTE: Press switch and hold momentarily each time to change brush pressure. INFORMATION DISPLAY LESS PRESSURE MORE PRESSURE 3-8

16 CONTROLS 5. SOLUTION CONTROL SWITCH This switch controls the amount of solution flow to the scrub deck. There are 5 different flow settings. To increase the solution flow, press the solution control switch (+). To decrease solution flow, press the top of the switch (-). If the brush motors are turned off or the direction control lever is in neutral, the flow is automatically interrupted until the motors are turned on again, or the drive pedal is moved forward or reverse. This feature prevents unintentional draining of the solution tank and allows the operator to adjust the solution flow to the scrub deck without resetting each time the scrubbing operation is interrupted. If recycling option is installed, this switch controls the amount of solution flow to the scrub deck by controlling the speed of the pump. NOTE: Press switch and hold momentarily each time to change solution flow. INFORMATION DISPLAY LESS SOLUTION MORE SOLUTION 6. VACUUM/SQUEEGEE SWITCH This switch independently controls the vacuum motor and squeegee position. To start the vacuum motor and lower the squeegee to the floor, press the bottom of the switch. To raise the squeegee and turn off the vacuum motor, press the top of the switch. The squeegee will raise after a 15 second delay, and the vacuum motor will turn off 15 seconds later, in order to clear vacuum hose of recovered solution. INFORMATION DISPLAY Indicates vac motor is running 3-9

17 CONTROLS 7. DISPLAY TOGGLE SWITCH The display toggle switch allows you to change the information display screen. Two screens are available. INFORMATION DISPLAY SCREEN 1 INFORMATION DISPLAY SCREEN 2 The hour meter is viewed on screen 2 of the information display. Hours are displayed for key ON time, brush run time, and traction motor time. Key ON Hours: Records the entire time that the key is on. Brush Run Time: Records the time spent with the brushes running and gives true brush motor time. Traction Motor Time: Records the time spent propelling the machine and gives true traction motor time. Fault codes/icon will appear on either display screen when the controller detects a problem within the electrical system. The codes/icons are used to assist users as well as service technicians in identifying and correcting problems. See troubleshooting section for more information on fault codes. The machine must be keyed off, then on again, to clear fault code after repair. 3-10

18 CONTROLS Icon appears if throttle is depressed when the key is turned on. To correct, lift foot off of throttle. If this does not clear the icon, the throttle may be damaged and should be checked by a qualified service technician. The float switch is located inside the recovery tank. The purpose of the float switch is to notify the user that the recovery tank is full. When the float switch is activated, the scrub brush motors and solution flow will stop, the scrub deck will raise, the squeegee will rise after 60 seconds, and the vacuum motor will turn off 10 seconds later. The battery meter can be viewed at the left side of either information screen 1 or information screen 2. The level of battery charge is indicated by the horizontal bars in the battery meter box. When the batteries require charging, the icon will flash and a battery inhibit icon will appear on the right side of either information screen. Scrub and solution functions that are running when the battery inhibit icon appears will be automatically shut off. It is not possible to restart scrub functions while the battery inhibit is displayed. The controller reserves enough battery charge to allow pick-up of residual water and transport back to a charging station. 3-11

19 CONTROLS 8. RECYCLE SWITCH (OPTIONAL) This switch controls the solution recycle pump. To start recycle pump, press the switch. A green light above the circuit breakers will indicate that pump is on. The solution control switch will control the speed of the pump and therefore the amount of solution flow to the scrub deck. Make sure there is an adequate amount of water in recovery tank before starting recycle pump, and turn off recycle pump when water level reaches filter. To stop the solution recycle pump, press the switch. The pump will stop and the green indicator light will turn off, and the solenoid valve will resume control of solution flow to the scrub deck. 9. RECYCLE INDICATOR LIGHT (OPTIONAL) This light will turn on when the recycle pump is on, and turn off when the recycle pump is off. 10. HEADLIGHT SWITCH (OPTIONAL) Turns on optional headlight for improved visibility in low light areas. 3-12

20 CONTROLS 11. BRAKE PEDAL The brake pedal is located on the floor to the left side of the steering column pedestal. The pedal operates the disc brakes on the drive wheels. To slow or stop the vehicle, apply pressure to the brake pedal. 12. PARKING BRAKE KNOB The orange knob located on the left side of the steering column pedestal is used to set the parking brake. To set the parking brake, fully depress the brake pedal and push the parking brake knob. To release the parking brake, fully depress the brake pedal. Then release pressure on the brake pedal. The parking brake knob will return it to its released position. FOR SAFETY: Before leaving or servicing machine; stop on level surface, set parking brake, turn off machine and remove key. 13. DIRECTIONAL CONTROL PEDAL AND SPEED REDUCTION FEATURE This pedal controls the direction of travel and the speed of the vehicle. Slowly pressing the front of the pedal causes the machine to travel forward. Pressing the rear of the pedal causes the vehicle to travel in reverse. The vehicle speed can be controlled by varying the pressure on the front or rear of the pedal. FOR SAFETY: The vehicle can coast for a short distance after releasing the directional pedal. Remove the foot from pedal and use brakes to slow or stop the machine. SPEED REDUCTION FEATURE Maximum speed of machine can be decreased to 80% of maximum by disconnecting wire 41 white from wire 42 white, located at 20 pin connector at controller. Machine is set at 100% speed setting at factory. 3-13

21 CONTROLS 14. HORN BUTTON The horn button is located on the control panel at the left side of the steering wheel. The horn is activated by pushing the button. 15. STEERING WHEEL The steering wheel articulates the machine to turn in the direction desired by the operator. 16. STEERING TILT LEVER The steering tilt lever is located on the right side of the steering wheel. To engage the tilt adjustment, pull up on the lever and adjust the steering column to desired position. Release lever and allow it to lock into desired position. 17. SQUEEGEE CAMBER ADJUSTMENT KNOB The squeegee camber adjustment knob is located at the center of the squeegee at the rear of the machine. (See maintenance section for adjustment). 18. SQUEEGEE DEFECTION ADJUSTMENT KNOB The squeegee deflection knob is located at the rear of the machine, on right side of the squeegee assembly. (See maintenance section for adjustment). 3-14

22 MACHINE OPERATION PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. 1. Visually check for exterior damage, leaks, damaged or worn tires. 2. Check brushes or pads and drivers for proper installation and wear. Weekly check scrub deck skirts for proper contact with floor. See BRUSHES in MAINTENANCE SECTION. 3. Check debris hopper (cylindrical scrubhead) to be sure it is empty. 4. Check squeegee for wear and proper adjustment. See SQUEEGEE ADJUSTMENT in MAINTENANCE SECTION. 5. Check for securely attached drain hose, plug, and caps. 6. Check battery condition, recharge if necessary. See BATTERIES in maintenance section. 7. Check the brakes and steering for proper operation. See BRAKES and STEERING in MAINTENANCE SECTION. STARTING MACHINE NOTE: Perform pre-run machine check before operating machine. FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly. FILLING THE MACHINE FOR SAFETY: Before leaving or servicing machine; stop on level surface, set parking brake, turn off machine and remove key. 1. Set squeegee and scrub deck to up position, set parking brake, and turn off key switch. 2. Remove solution tank cover.! WARNING Flammable materials can cause an explosion or fire. Do not use flammable materials in the tanks. 3. The solution tank can be filled to the bottom lip of the fill inlet. Leave room for detergent. The solution tank capacity is 50 gallons (189 liters). The water must not be hotter than 140 (60 C) to prevent damage to the tank. Measure the required amount of chemical into the solution tank after filling with water. Dry chemicals should be thoroughly mixed before being added into solution tank. Commercially available, high alkaline floor cleaners are suitable for use in the solution system. 4. Inspect solution tank cover vent for obstructions. Replace solution tank cover. 1. The operator should be in the seat with foot on the brake pedal or with the parking brake on. The directional pedal must be in the neutral position to avoid unintentional movement. NOTE: The Operator must be in position on the seat to activate machine in desired direction. 2. Turn the key switch clockwise to the ON position. 3. Release the brake, then press lightly on the directional pedal in the desired direction and drive to the filling area. 3-15

23 MACHINE OPERATION SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising or lowering scrub deck/squeegee. In order to achieve the best possible results, the area that is to be cleaned should be swept before scrubbing. Large debris, strings and wire must be removed to prevent being caught in brushes or squeegee. The machine will automatically raise the squeegee slightly when reverse travel is selected. If the machine is allowed to stand in neutral with the scrub deck down for more than 2 seconds, the solutions flow stops and brush motors stop. If either forward or reverse travel is selected, the solution flow will continue in the same setting and the scrub brush motors will continue in their same setting once movement of machine begins. Overlap the brush path and avoid transporting over previously cleaned areas. TO BEGIN SCRUBBING! CAUTION When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. 1. Place foot on brake pedal or check to make sure parking brake has been set. 2. With directional pedal in neutral turn key switch to ON. 3. Release brake. 4. Press the directional pedal to travel in the desired direction and steer to the start of the scrub pattern. 5. Press the one-touch switch (#1) on the control panel. The brush motors will start, the scrub deck will lower to the light scrub position, the solution will begin to flow, the squeegee will lower to the floor and the vacuum motors will start. 6. Adjust the speed of the machine, solution flow and scrub brush pressure as necessary. NOTE: Once solution flow rate is set it is not necessary to shut off solution when stopping scrubbing. Solution flow is automatically shut off when brush motors stop. When brush motors are activated, flow automatically resumes.! WARNING Flammable liquids and/or reactive metals can cause explosions or fire! Do not pick up. 3-16

24 MACHINE OPERATION TO STOP SCRUBBING 1. Press the one-touch switch (#1) on the control panel. The brush motors will stop and the scrub deck will raise to the park position. After 15 seconds, the squeegee will raise, and 15 seconds later the vacuum motor will turn off. This delay is to clear the vacuum hose of recovered solution. 2. Allow directional pedal to return to neutral. 3. Apply brake to stop machine. 4. Turn key switch off. 5. Set parking brake. FOR SAFETY: Before leaving or servicing machine; stop on level surface, set parking brake, turn off machine and remove key. EMERGENCY STOP PROCEDURE 1. Turn key switch to off position. If an electrical problem is suspected push in emergency stop button. 2. Release pressure on directional pedal. 3. Apply brakes. DOUBLE SCRUB Floors which are heavily soiled or have thick accumulation of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, make the first pass over the surface being cleaned with the squeegee up, the solution on, and brushes down. This allows the solution to stay in contract with the soil while loosening the surface accumulation with the brushes. Allow time for the first application to stay in contact with floor. Length of time between the first and second pass depends on amount of accumulation and the type of chemical being used. A second scrubbing with the squeegee down and again the solution and brushes on will further loosen soil. The additional application of solution will further assist the difficult cleaning job. Caution should be used when double scrubbing, maintain safe driving speed on wet floors. NOTE: Turning the key switch off during normal running operation will stop all motors and actuators. When the key is turned back on the system will automatically return scrub deck and squeegee to raised position. 3-17

25 MACHINE OPERATION EMPTYING AND CLEANING TANKS RECOVERY TANK 1. Touch the scrub deck switch (#1) on the console to raise the scrub deck, stop the motors, raise the squeegee and turn off vacuum motors and solution. 2. Park the machine next to a floor drain. Drain hose is on left rear corner of machine. 3. Turn off the key switch and set the machine s parking brake. 4. Unhook the drain hose from retainer. Unscrew T-handle on plug enough to loosen plug and lower hose in direction of drain. Stand behind end of hose. Recovered solution will come out with force. Slowly remove plug from drain hose. 5. Recovery tank should be flushed out with clean water on a daily basis. Direct water from fill hose into recovery drain hose. Repeat until clean water comes out of drain hose. Do not use water hotter than 140 F (60 C) to clean the tank. Damage to tank may occur. 6. Large debris or compacted dirt may be removed by clean out cap located at rear lower center of recovery tank. Regular flushing of recovery tank should make this step unusual. 7. Replace plug and secure drain hose in bracket. 8. If machine is to be stored, leave recovery tank cover open and drain hose off. SOLUTION TANK 1. Park the machine next to a floor drain. Drain hose is on right side at middle. 2. Turn off the key switch and set the machine s parking brake. 3. Unhook the small drain hose from the retainer. Unscrew T-handle on plug enough to loosen plug, then lower hose in direction of the drain. Slowly remove plug from drain hose. 4. Remove the solution tank cover. 5. Flush the solution tank out with clean water and run several gallons of clean water through systems. Do not use water hotter than 140º F (60º C) to clean tank. Damage may occur. NOTE: Never allow solution to remain in tank. Damage to tank, seals and valves could occur. 6. Replace the drain plug and secure drain hose in bracket. DRAIN HOSE SOLUTION TANK DRAIN SOLUTION TANK LID CLEAN OUT REAR VIEW TOP VIEW 3-18

26 MAINTENANCE Batteries 2. Squeegee Assembly 3. Scrub Head (Disk Shown) 4. Drive Chains 5. Brakes 6. Tires and Wheels 7. Solution Strainers 8. Float Switch 9. Vacuum Motors 10. Brush Motors 11. Fuse 12. Circuit Breakers 4-1

27 MAINTENANCE 1. BATTERIES The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. To get the greatest life from the batteries charge them when their charge level reaches 25%of a full charge. Use a hydrometer to check the charge level. Do not allow the batteries to remain in a discharged condition for any length of time. Never expose a discharged battery to temperatures below freezing. Discharged batteries will freeze causing cracked case. Do not operate the machine if the batteries are in poor condition or if they have a charge level below 25%, specific gravity below Keep all metallic objects off the top of the batteries, as they may cause a short circuit. Replace worn or damaged cables and terminals. Check the electrolyte level in each battery cell before and after charging the batteries. Never add acid to the batteries use water. Do not allow water level to fall below the battery plates. Portions of plates exposed to air will be destroyed. Do not overfill. Keep plugs firmly in place at all times.! WARNING When servicing machine, avoid contact with acid.! WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.! WARNING Wear eye protection and protective clothing when working with batteries.! WARNING Charge batteries in a well ventilated area. BATTERY MAINTENANCE 1. When cleaning the batteries, use a solution of baking soda and water. Do not allow the cleaning fluid to enter the battery cells. Electrolyte will be neutralized. 2. Maintain the proper electrolyte level in each battery cell. If a cell should accidentally overflow, clean immediately. 3. Do not add water until the battery is fully charged. 4. Wipe off the top of the batteries at least once a week. 5. Test battery condition with a hydrometer at least once a week. 6. Ensure that all connections are tight and all corrosion removed. 7. Every 4 to 6 months remove the batteries from the machine and clean the battery cases and battery compartment. NOTE: Do not take readings immediately after adding water. If the water and acid are not thoroughly mixed, the reading may not be accurate. To find the correct specific gravity reading when the temperature of the battery electrolyte is other than 80 F (27 C). Add (+) to the specific gravity reading (4 points), for each 10 F (6 C) above 80 F (27 C) Subtract (-) from the specific gravity reading (4 points), for each 10 F (6 C) below 80 F (27 C). SPECIFIC GRAVITY BATTERY CONDITION % CHARGED % CHARGED % CHARGED % CHARGED DISCHARGED 4-2

28 MAINTENANCE TO CHARGE BATTERIES! WARNING! WARNING! WARNING! WARNING When servicing machine, avoid contact with acid. Batteries emit hydrogen! WARNING gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. Charge batteries in a well ventilated area. 1. Stop the machine in a clean, well ventilated area next to the charger. 2. Turn the machine off and set parking brake. FOR SAFETY: Before leaving or servicing machine, stop on level surface, apply parking brake, turn off machine and remove key. 3. Raise the tank and raise the support arm to lock in place. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC first. Hazardous sparks may result. 7. Use a 36 volt DC charger that will automatically shut off when the batteries are fully charged to charge the six battery pack. 8. Plug the charger into the battery connector. Plug charger into power outlet. The charger gauge should indicate that the batteries are charging. If the charger does not automatically start up, verify that charger is plugged into batteries. 9. When the batteries are fully charged, disconnect the charger from the batteries. 10. Connect the batteries to the machine connector. 11. Check the electrolyte level. It should be up to the indicator ring. If necessary add distilled water. 12. Lower the tank. Charger connection 4. Check the electrolyte level in each battery cell. Before charging, add just enough water to cover up the plates. After recharging has completed, add just enough water to bring up the level to the indicator ring. If water level is too high before charging, normal expansion of the electrolytes may cause and overflow, resulting in loss of battery acid balance and damage to the machine. 5. Replace battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machine. Unplug the battery charger from power outlet. 4-3

29 MAINTENANCE LOW BATTERY SHUT-DOWN The electronic system is equipped with battery voltage sensors. When the batteries are exhausted to a preset level, the scrubbing system will shut down to protect the batteries from damage, and the battery lockout icon will appear on the display. TO REMOVE BATTERIES TO REPLACE BATTERIES 1. Refer to diagram. Place batteries in battery compartment. 2. Connect all jumper cables positive to negative to the six batteries. 3. Connect the positive cable to battery in the position shown. 4. Connect negative cable to battery in the position shown. + _ 1. Stop the machine in a clean area next to the charger. 2. Turn off machine and set parking brake. _ BLK _ BLK RED+ FOR SAFETY: Before leaving or servicing machine, stop on level surface, apply parking brake, turn off machine and remove key. 3. Drain recovery tank. 4. Raise the tank and raise the support arm to lock in place. 5. Disconnect battery pack from the machine. 6. Use the proper size open end wrench to disconnect main ground wire first and secure cable terminal away from batteries. 7. Disconnect main positive lead and secure cable terminal away from battery/batteries. 8. Loosen both terminals on each jumper cable and remove one at a time. 9. Prepare a suitable battery site to place batteries. 10. Attach suitable battery lifting device and lift batteries from the machine. + RED RED + _ BLK + RED RED + _ BLK _ BLK RED + _ BLK! CAUTION Batteries are a potential environmental hazard. Consult your battery supplier for safe disposal methods. 4-4

30 MAINTENANCE 2. SQUEEGEE ASSEMBLY The steering geometry and the design of the squeegee assembly allows the squeegee assembly to follow the track of the scrub head even in hard turns. Turns are not pushed sideways around a pivot point but turn in an arc. This feature eliminates the need to use side squeegees. The assembly rides on the floor supported by two wheels that follow changing levels in the floor. Down pressure and squeegee flair is constant in relation to the floor. Spring tension is applied to the squeegee to maintain good contact with the floor NOTE: Refer to ADJUSTING SQUEEGEE below. Rollers are mounted on each end of the squeegee assembly to assist in rolling by obstacles. The squeegee assembly is easily removed from lift mechanism for service and transport. SQUEEGEE ADJUSTMENT Adjusting the squeegee is a two-part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as at the center. The pitch adjustment is facilitated by the use of a spirit level mounted on the squeegee tool. The second adjustment is the amount of deflection or bend in the rear blade. This deflection is controlled by the height of the tool from the floor. That height is varied by the wheel adjustment. TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn on the key switch, release the machine parking brake, lower the squeegee and drive forward at least 2 feet (60 cm). 2. With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 3. Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across tool. This should correspond to the bubble being in the middle position of the spirit level. 4. To decrease the deflection of the squeegee blade at the ends, turn knob on squeegee trailing arm clockwise. To increase the deflection at the ends of the squeegee assembly, turn knob counter clockwise. 5. Again check the deflection of the squeegee blades. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade. TO ADJUST SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet. 2. With the squeegee down, stop the machine and set the parking brake. Do not allow the machine to roll back. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 3. Observe the amount of squeegee deflection. It should deflect 3/8in (9.5 mm) across the entire width of the squeegee. 4. To adjust the squeegee defection, loosen knob on the squeegee slide bar. 5. Sliding bar to the left increases deflection. Sliding bar to the right decreases deflection. 6. Tighten knob on squeegee slide bar. 7. Turn on the key switch and release the parking brake. Raise and then lower squeegee assembly. Drive forward at least 2 feet (60 cm). 8. Repeat steps 2 through 7 until deflection of 3/8 in. (9.5 cm) is reached. SQUEEGEE DEFLECTION CORRECT NOT ENOUGH TOO MUCH SIDE VIEW OF SQUEEGEE BLADE 4-5

31 MAINTENANCE TO REMOVE SQUEEGEE ASSEMBLY 1. With the squeegee in the up position, turn off the key switch and set the parking brake. 2. To remove squeegee tool to work on bench, raise the recovery tank and raise the support arm to lock in place. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 3. Disconnect vacuum hose and loosen the two squeegee retaining knobs. 4. Pull squeegee assembly rearward from the lifting carrier. 5. With squeegee assembly on bench inspect or repair as necessary. 6. To reinstall, align squeegee assembly to lift carrier. Push forward until squeegee is fully engaged. 7. Tighten knobs. 8. Attach vacuum hose. TO REPLACE OR ROTATE REAR SQUEEGEE BLADES 1. With the squeegee in the up position, turn off the key switch and set the parking brake. SQUEEGEE ASSEMBLY SQUEEGEE ASSEMBLY CARRIER REAR VIEW TO REPLACE OR ROTATE FRONT SQUEEGEE BLADES 1. With squeegee assembly on bench, loosen retaining bolt and locking nut on the left side of the retaining strap. 2. Remove front retainer strap. 3. Remove squeegee blade from locating pins on squeegee tool and rotate to new position or replace as required. 4. Install blade on locating pins of squeegee tool. 5. Replace front retainer strap. 6. Secure strap by tightening retaining bolt and locking nut on retainer strap. NOTE: Changing of squeegee blades does not always necessitate a readjustment. Refer to section on adjusting squeegee. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 2. Unlock and pull open latch on rear of squeegee tool. 3. Remove blade retainer straps from squeegee tool. 4. Remove squeegee blade from locating pins on squeegee tool and rotate to new position or replace as required. 5. Install blade on locating pins of squeegee tool. 6. Install squeegee retainer straps. 7. Fasten and lock latch. Latch is adjustable. Adjust latch only tight enough to take up slack in retaining strap. NOTE: Changing of squeegee blades does not always necessitate a readjustment. Refer to section on adjusting squeegee. 4-6

32 MAINTENANCE 3. SCRUB HEAD-DISK The scrub head consists of two rotary type scrub brushes, drive motors, and splash skits. The operator can select one of five different down pressures on the touch control panel. Adjustments are made automatically by the machine when floor conditions change. There are no mechanical adjustments to be made by the operator. The drive hub allows brushes to follow irregularities and changes in floor without losing contact with floor. SCRUB BRUSHES There are four different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market and further add to the flexibility of the machine. Please refer to the following to assist in selecting the proper brush or pad for the work at hand. UNCOATED FLOORS Aggressive Grit is a nylon fiber impregnated with silicone carbide grit. It grinds away stain, soil, and removes surface material. Mild Grit is a less aggressive silicone carbide grit suitable for cleaning medium soil conditions. Advantages are faster ground speed than nylon bristles on light solid applications. Nylon is a general-purpose scrub brush with stiff bristles. FINISHED FLOORS Nylon bristles are used in a variety of applications on coated or uncoated surfaces. Polypropylene bristles work on a variety of floor surfaces. Does not soften in water White Pads (Polishing) are used for dry polishing to achieve a high-gloss appearance, or surface washing on highly polished or burnished floors. Blue Pads (Scrubbing) are used for heavy-duty scrubbing and light stripping. The blue pads remove less finish than brown stripping pads, yet will remove black marks, stains and dirt. Brown Pads (Stripping) are used for easy and complete removal of old floor waxes/finishes. They will quickly remove ground in dirt, black heel marks, and spills. When used with the proper stripper, this pad leaves the floor clean and ready for finishing. REPLACING OR INSTALLING SCRUB BRUSHES The scrub brushes should be checked before each day s work for wire, string, wear, or damage. The scrub brushes should be replaced if brush bristles are missing or if shorter than 5/8 inch. NOTE: For uniform scrubbing, scrub brushes must be replaced as a set. 1. With the scrub deck up, turn off the machine and set the parking brake. 2. Locate release lever on top of brush or pad driver. With finger rotate release lever against spring pressure counter clockwise. Brush/pad driver will release and drop down. 3. To reinstall, center the cut out of the release lever plate on brush/pad driver to be installed under the brush drive hub. 4. Raise brush/pad drive up until assembly contacts brush hub. Rotate slightly until drive engages release lever plate. 5. While holding upward pressure, rotate brush/pad driver assembly clockwise. When fully engaged, release lever plate will rotate under spring pressure to lock assembly. NOTE: Check that release plate is completely closed and pad/brush is securely attached. Damage to driver or brush could occur. 6. Repeat the procedure for the opposite side of the machine. Red Pads (Buffing) are used for light-duty scrubbing. When used with a mild detergent they will provide surface cleaning without removing the finish. 4-7

33 MAINTENANCE SCRUB HEAD-CYLINDRICAL The dual cylindrical scrub head is designed to eliminate debris that may be caught in the squeegee while scrubbing. Water is applied to the first scrubbing brush turning in a clockwise rotation when viewed from the right or operator s side of machine. The first brush scrubs dirt and debris between the brushes. The second scrubbing brush, turning in a counter clockwise rotation, picks up debris and throws it into a removable hopper. The larger debris which might catch under the squeegee is collected in the hopper. Water is allowed to drain out the hopper into the squeegee path where it is recovered from the floor. The automatic operating procedure is the same as the disc machine. MAINTENANCE The brushes should wear evenly side to side if properly adjusted. Scrub brushes should be exchanged front to back every 50 hours to ensure even wear since the rear brush contacts the floor with more force. It is not necessary to rotate end for end since swapping front to back puts the brushes in the opposite rotation, as well as balancing wear. Scrub brushes should be replaced as a set when bristle length wears to height of yellow PerformAlert TM bristles. SCRUB BRUSH REPLACEMENT 1. Observe location of drive hub lugs. It is usually easier to position the lugs to the 12 o clock-6 o clock position (vertical) or 9 o clock-3 o clock position (horizontal). 2. Orient brush notches to match the position of the drive hub lugs and slide onto hub. It may be necessary to lift the drive side of the brush. 3. Push brush until a positive stop is felt. The idler plate cannot be installed until the brush is fully sealed on the drive hub. 4. Allow brush to drop below scrub deck. Line up lugs on idler plate with notched in brush and fully insert plate onto brush. 5. Line up hook on idler door with notches on side of scrub head. 6. Slide idler door up until lip rests on top of scrub head. 7. Latch door into position. SCRUB BRUSH REMOVAL The scrub brushes are removed from the side of the machine. The front is removed front the right side and the rear is removed from the left side. 1. Unlatch idler side door. 2. Pull out on top of door until lip on door clears brush head. 3. Push down on door until hooks on door are free of scrub head side. 4. Pull out on door with a rocking motion to free idler door from end of brush. 5. Pull brush out with a rocking motion to free brush from drive hub. 4-8

34 MAINTENANCE DUMPING HOPPER The removable hopper is located behind the rear scrub brush. If the hopper becomes full, it will not accept any more debris. Remove the hopper by sliding it out from the operator s side of the machine. The hopper can then be dumped from the top or the left side door can be removed to dump debris from the end. The side door is also convenient for flushing the hopper clean with running water. BELT REPLACEMENT 1. Remove scrub brushes. 2. Remove four bolts securing broom drive seal and retainer. 3. Slacken belt tension by means of jack bolt under motor. 4. The drive hub may be unscrewed from the inside. Flats are provided on interior drive pulley axle to facilitate removal. 5. Place belt on motor pulley then pull down into scrub head. 6. Insert drive hub from inside of scrub head and through lower loop of belt. 7. Screw axle into side of scrub head. 8. Re-tension belt to deflect 1/8 at center of span when a pressure of 4 pounds is applied. 9. Install broom drive seal and retainer. 10. Install scrub brushes. SCRUB DECK ADJUSTMENT Scrub deck adjustment consists of two types of adjustments. The first is to insure the individual brushes make the same width pattern end to end. Any tapered brush pattern should be adjusted out. The second is to make the pattern of equal width between front and rear brushes. Unequal patterns are caused by the scrub deck not being parallel to the floor. Proper adjustment is obtained when the contact patterns of the brushed on the floor show two 1 rectangles the width of the brushed. The rectangles should be parallel to each other. TESTING, ADJUSTMENT OF INDIVIDUAL BRUSHES 1. Move the machine to an unfinished area of floor to avoid marking finish. 2. With water valve off, lock brakes, and lower scrub head to floor. Allow brushes to run until automatic shut off occurs. It may be necessary to repeat this step in the same location until a good mark can be seen on the floor. This can be accomplished by touching lightly the directional pedal to restart the scrub deck without moving the machine. 3. Raise the scrub deck and note the brush patterns on the floor. There should be two rectangles with parallel sides. If the pattern is tapered, proceed as follows. ADJUSTMENT OF INDIVIDUAL BRUSHES The brush pattern is adjusted front he idler side only. The idler shaft is locked into position by means of an allen head screw on the idler door. The shaft is secured in an eccentric position. With the screw loose the shaft may be rotated by means of the flats machined on the interior side of the shaft to achieve different heights. 1. Determine if idler is to be moved up or down to balance the pattern. 2. Remove idler door on brush to be balanced. 3. Measure distance of axle from top of door and record. 4. Loosen allen head screw from outside door. 5. Rotate shaft to new position. Hold shaft in position. 6. Tighten allen head screw. 7. Install door on machine. 8. Re-start and readjust as necessary. LEVELING THE SCRUB HEAD Leveling the cylindrical head is accomplished by a single bolt and lock nuts located in the adjustment channel at rear, center of the scrub deck. To increase pattern width on rear brush, loosen lock nuts on socket head cap screw and adjust screw cap down. To increase pattern width on front brush, adjust screw up. After adjustment, be sure to tighten lock nuts. 4-9

35 MAINTENANCE 4. DIFFERENTIAL DRIVE CHAIN The differential drive chain transfers power from the drive motor to the differential. Check the chain condition every 200 hours of operation. A tight chain causes wear on bearings, chain, and increased power consumption. A worn chain causes wear on the sprocket. ADJUSTING DIFFERENTIAL DRIVE CHAIN DRIVE WHEEL CHAIN The drive wheel chains transfer power from the differential shaft to the drive wheels. Check chain condition and tension every 200 hours of operation. The chain should deflect 1/2 in (13 cm) on the side opposite the idler. Lubrication of drive chain is not recommended. Clean dirt and grease build up from chain to eliminate the abrasive effects. ADJUSTING THE DRIVE WHEEL CHAINS FOR SAFETY: Before leaving or servicing machine: Stop on level surface, set parking brake, turn off machine and remove key. 1. From underneath the rear of machine loosen the two motor mounting bolts. Do no remove bolts. For ease of service, bolts screw into nut plates. It is not necessary to use a backup wrench. 2. There are two nuts on the threaded rod attached to the motor position bracket. Loosen the nuts. 3. Tighten the nut in front of frame cross member to increase chain tension. Screw the nut to the rear of frame away from the motor to decrease chain tension. On the slack side, chain should deflect between 1/2 and 3/4 measured midway between the center lines of the sprockets. 4. Tighten nuts against each other to fix adjustment. 5. Tighten motor mounting bolts. 1. Turn off machine with key switch and set parking brake. FOR SAFETY: Before leaving or servicing machine; Stop on level surface, set parking brake, turn off machine and remove key. 2. Loosen the two bolts on the chain tension plate. 3. Slide the plate to adjust tension. 4. Tighten chain tensioner mounting bolts. 4-10