REMOVAL & INSTALLATION

Size: px
Start display at page:

Download "REMOVAL & INSTALLATION"

Transcription

1 REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT Removal (Eclipse & Galant) 1. Raise and support vehicle. Remove engine splash shield from right side wheelwell. 2. Lower vehicle. Support weight of engine with floor jack. If necessary, remove coolant reservoir. Remove upper engine mount located near timing belt cover. Remove all drive belts. If necessary, remove drive belt tensioner pulley bracket and power steering pump pulley. See Fig. 1. Remove water pump pulley. 3. Remove crankshaft pulley. Noting bolt lengths and locations, remove upper and lower timing belt cover with gasket. CAUTION: DO NOT rotate crankshaft counterclockwise (as viewed from timing belt end of engine). If timing belt is to be reused, mark direction of rotation before removing. 4. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with timing mark on cylinder head. See Fig Loosen timing belt tensioner center bolt, and move tensioner pulley toward water pump. Tighten center bolt to secure tensioner. Remove front timing belt. Remove tensioner pulley and timing belt auto tensioner. 6. To remove balance shaft belt, remove left balance shaft access plug from cylinder block. Insert.31" (8.0 mm) diameter Phillips screwdriver to block left silent shaft. See Fig. 3. Ensure screwdriver can be inserted at least 2.36" (59.9 mm). Remove screwdriver if it cannot be inserted at least 2.36" (59.9 mm). Rotate balance shaft one revolution and realign timing mark. 7. If reusing old balance shaft timing belt, mark belt with arrow to indicate rotation direction. Holding crankshaft stationary, remove front crankshaft sprocket bolt. Use gear puller to remove crankshaft sprocket from crankshaft. 8. Noting direction of installation, remove crankshaft sensing blade. Loosen balance shaft tensioner pulley center bolt. Remove balance shaft timing belt. Inspect timing belt. See TIMING BELT INSPECTION. Wednesday, March 24, :06:38 4:06:41 PM Page Mitchell Repair Information Company, LLC.

2 Fig. 1: Exploded View Of Drive Belts & Timing Belt Components (Eclipse & Galant Shown; 1999 & Up Is Similar) Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

3 Fig. 2: Aligning Front Timing Belt Marks Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

4 Fig. 3: Locking Balance Shaft Installation (Eclipse & Galant) 1. Align crankshaft rear sprocket and balance shaft sprocket timing marks. See Fig. 4. Install balance shaft timing belt. Ensure there is no slack in belt. If reusing old belt, install in original direction of rotation. 2. Ensure crankshaft components are clean. Install crankshaft sensing blade in correct direction. See Fig. 6. Install crankshaft sprocket. Apply engine oil to threads of crankshaft sprocket bolt. Install and tighten bolt to specification. See TORQUE SPECIFICATIONS. 3. Move the balance shaft tensioner pulley so that the center of the tensioner pulley is above and to the left of the centerline of the tensioner center bolt. See Fig. 5. The tensioner pulley flange should face toward the front of the engine. CAUTION: When tightening balance shaft tensioner pulley center bolt, ensure tensioner pulley shaft does not rotate with bolt. This will place excessive tension on bolt. 4. Using your hand, place pressure on balance shaft tensioner pulley in direction of balance shaft timing belt. Loosen balance shaft tensioner pulley center bolt. Ensure balance shaft timing belt is taut (no slack), and tighten balance shaft tensioner pulley center bolt. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

5 5. Press balance shaft belt on side opposite tensioner to check belt deflection. See Fig. 4. Balance shaft belt deflection should be " ( mm). Adjust as necessary. NOTE: DO NOT remove Phillips screwdriver from side of engine block until camshaft timing belt is installed. 6. Using a soft-jawed vise, SLOWLY compress the timing belt auto tensioner push rod until rod pin hole aligns with pin hole in tensioner body. Insert a locking pin through tensioner body and tensioner push rod pin holes to lock auto tensioner in position. Install auto tensioner on engine with locking pin in place. Install tensioner pulley. 7. Ensure all timing marks are still aligned. See Fig. 2. Install timing belt on crankshaft sprocket, oil pump sprocket, then camshaft sprocket. If reusing old timing belt, ensure belt is installed in original direction of rotation. Make sure there is no slack in timing belt between sprockets. 8. Set the timing belt tensioner pulley so that pin holes are at the bottom of the pulley. See Fig. 7. Press tensioner pulley lightly against the timing belt. Temporarily tighten tensioner pulley center bolt. CAUTION: To prevent breaking auto tensioner push rod, turn Set Screw (MD998738) by hand only. 9. Install Set Screw (MD998738) into rear timing belt cover. See Fig. 7. Screw in set screw by hand until tensioner bracket arm makes contact with auto tensioner push rod end. 10. Remove Phillips screwdriver from engine block and install plug. To adjust timing belt tension, turn crankshaft 1/4 revolution counterclockwise. Turn crankshaft clockwise until all timing marks are aligned. 11. Loosen the tensioner pulley center bolt. Install Adapter (MD998767) and torque wrench on tensioner pulley. See Fig. 8. Apply 31 INCH lbs. (3.5 N.m) of torque while tightening tensioner pulley center bolt to specification. See TORQUE SPECIFICATIONS. DO NOT let tensioner pulley turn while tightening center bolt. 12. Remove locking pin from auto tensioner. Remove set screw. 13. Turn crankshaft 2 revolutions clockwise. Align all timing marks. Let vehicle sit for 15 minutes. Measure auto tensioner rod protrusion between auto tensioner housing and point where it contacts tensioner arm. Protrusion should be " ( mm). If protrusion is not as specified, repeat timing belt tensioning procedure. 14. Install timing belt covers. Ensure bolts are installed in original locations. See Fig. 9. Continue installation in reverse order of removal procedure. Adjust drive belts to proper tension. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

6 Fig. 4: Aligning Balance Shaft Timing Marks Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

7 Fig. 5: Adjusting Balance Shaft Timing Belt Tensioner Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

8 Fig. 6: Installing Crankshaft Sensing Blade (Eclipse & Galant) Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

9 Fig. 7: Installing Set Screw On Tensioner Pulley Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

10 Fig. 8: Adjusting Timing Belt Tension Fig. 9: Timing Belt Cover Bolt Installation Locations Removal (Montero Sport) 1. Drain engine coolant. Remove upper radiator hose. Loosen the cooling fan clutch-to-pulley nuts. Remove accessory drive belts. Remove fan shroud and cooling fan clutch with pulley. CAUTION: Never rotate crankshaft counterclockwise. 2. Rotate crankshaft clockwise so that No. 1 piston is at TDC of compression stroke. Leaving secondary wires attached, remove distributor cap and set aside. 3. Note installed position of distributor and distributor rotor. Unplug distributor electrical connector. Remove distributor housing and set aside. 4. Disconnect ignition power transistor and ignition coil connector. Remove ignition coil. Remove timing Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

11 belt upper cover. 5. Holding crankshaft stationary, remove crankshaft pulley bolt. Remove crankshaft pulley. Remove distributor bracket. See Fig Remove timing belt lower cover. Align timing mark on camshaft sprocket with timing mark on cylinder head. See Fig Loosen timing belt tensioner center bolt, and remove tensioner toward water pump. Tighten center bolt to secure tensioner. If reusing old timing belt, mark belt with arrow to indicate original direction of rotation. Remove timing belt. Remove timing belt auto tensioner. 8. To remove balance shaft timing belt, remove left balance shaft access plug from cylinder block. Insert.31" (8.0 mm) diameter Phillips screwdriver to block left silent shaft. See Fig. 3. Ensure screwdriver can be inserted at least 2.36" (59.9 mm). Remove screwdriver if it cannot be inserted at least 2.36" (59.9 mm). Rotate balance shaft one revolution and realign timing mark. 9. If reusing old balance shaft timing belt, mark belt with arrow to indicate rotation direction. Loosen balance shaft tensioner pulley center bolt. Remove balance shaft timing belt. Inspect timing belt. See TIMING BELT INSPECTION. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

12 Fig. 10: Exploded View Of Timing Belt & Components (Montero Sport) Installation (Montero Sport) 1. Align crankshaft sprocket and balance shaft sprocket timing marks. See Fig. 4. Install balance shaft timing belt. If reusing old belt, install in original direction of rotation. 2. Move the balance shaft tensioner pulley so that the center of the tensioner pulley is above and to the left of the centerline of the tensioner center bolt. See Fig. 5. The tensioner pulley flange should face toward the front of the engine. 3. Using your hand, place pressure on balance shaft tensioner pulley in direction of balance shaft timing belt. Loosen balance shaft tensioner pulley center bolt. Ensure balance shaft timing belt is taut (no slack), and tighten balance shaft tensioner pulley center bolt. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

13 NOTE: When tightening balance shaft tensioner pulley center bolt, ensure tensioner pulley shaft does not rotate with bolt. This will place excessive tension on belt. 4. Press balance shaft belt on side opposite tensioner to check belt deflection. See Fig. 4. Balance shaft belt deflection should be " ( mm). Adjust as necessary. 5. Using a soft-jawed vise, SLOWLY compress the timing belt auto tensioner push rod until rod pin hole aligns with pin hole in tensioner body. Insert a locking pin through tensioner body and tensioner push rod pin holes to lock auto tensioner in position. Install auto tensioner on engine with locking pin in place. 6. Ensure all timing marks are still aligned. See Fig. 2. Install timing belt on engine. If reusing old timing belt, ensure belt is installed in original direction of rotation. Make sure there is no slack in timing belt between sprockets. NOTE: DO NOT remove Phillips screwdriver from side of engine block until camshaft timing belt is installed. 7. Set the timing belt tensioner pulley so that pin holes are at the bottom of the pulley. See Fig. 7. Press tensioner pulley lightly against the timing belt. Temporarily tighten tensioner pulley center bolt. CAUTION: To prevent breaking auto tensioner push rod, turn Set Screw (MD998738) by hand only. 8. Install Set Screw (MD998738) into rear timing belt cover. See Fig. 7. Screw in set screw until tensioner bracket arm makes contact with auto tensioner push rod end. 9. Remove Phillips screwdriver from engine block and install plug. To adjust timing belt tension, turn crankshaft 1/4 revolution counterclockwise. Turn crankshaft clockwise until all timing marks are aligned. 10. Loosen the tensioner pulley center bolt. Install Adapter (MD998767) and torque wrench on tensioner pulley. See Fig. 8. Apply 31 INCH lbs. (3.5 N.m) of torque while tightening tensioner pulley center bolt to specification. See TORQUE SPECIFICATIONS. DO NOT let tensioner pulley turn while tightening center bolt. 11. Remove locking pin from auto tensioner. Remove set screw. 12. Turn crankshaft 2 revolutions clockwise. Align all timing marks. Let vehicle sit for 15 minutes. Measure auto tensioner rod protrusion between auto tensioner housing and point where it contacts tensioner arm. See Fig. 11, Dimension "A". Protrusion should be " ( mm). If protrusion is not as specified, repeat timing belt tensioning procedure. 13. Install timing belt lower cover, distributor bracket, and timing belt upper cover. Install distributor, distributor cap, and ignition coil. 14. Install cooling fan clutch, pulley, fan shroud, and upper radiator hose. Continue installation in reverse order of removal procedure. Fill and bleed cooling system. Adjust ignition timing. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

14 Fig. 11: Measuring Timing Belt Auto Tensioner Protrusion TIMING BELT INSPECTION 1. Inspect back of belt for being hard, non-elastic and having a glossy surface. Check for rounded sides on belt. Sides of belt should be straight and clear-cut. Flaking, peeling, cracking rubber from canvas also indicates that belt should be replaced. Cracks are most evident at base of tooth. 2. Abnormal wear most often occurs on load side of tooth. Fluffy canvas, unclear canvas texture, belt color changed to White from rubber missing, reduced tooth width or a missing tooth warrant belt replacement. 3. Check timing belt and balance shaft belt tensioner pulleys for worn bearings. Replace as necessary. 4. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 12. Length should be.47" (12 mm). Apply lbs. (20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39" (1 mm), replace the auto tensioner. Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

15 Fig. 12: Inspecting Timing Belt Auto Tensioner Wednesday, March 24, :06:38 PM Page Mitchell Repair Information Company, LLC.

2002 Mitsubishi Montero Limited

2002 Mitsubishi Montero Limited Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

2003 Hyundai Sonata LX

2003 Hyundai Sonata LX TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate

More information

IMING BELT COMPONENTS REMOVAL

IMING BELT COMPONENTS REMOVAL 1 of 11 11/21/2012 2:21 PM IMING BELT COMPONENTS REMOVAL 1. Remove the wheel of passenger side. 2. Remove the side cover. 3. Remove the engine cover. 4. Disconnect the power steering hose fixing on the

More information

2001 Dodge Dakota ENGINES 4.7L V8

2001 Dodge Dakota ENGINES 4.7L V8 FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.

More information

2003 Hyundai Truck Santa Fe V6-3.5L

2003 Hyundai Truck Santa Fe V6-3.5L Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder

1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness

More information

TIMING BELT REMOVAL - TIMING BELT

TIMING BELT REMOVAL - TIMING BELT 2004 Chrysler Concorde V6-3.5L VIN M Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Procedures TIMING BELT REMOVAL - TIMING BELT CAUTION: The following

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE 1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn

More information

Timing Belt: Service and Repair

Timing Belt: Service and Repair 2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata

More information

DISASSEMBLY. SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System

DISASSEMBLY. SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System DISASSEMBLY 1. Remove the engine cover. 2. Disconnect the battery negative terminal. 3. Disconnect the radiator lower hose. 4. Disconnect the

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft

More information

1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE).

1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE). 1Search TIMING BELT 2005 Chrysler Pacifica 3.5L Eng Base FRONT TIMING BELT COVER REMOVAL 1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE). 2. Disconnect

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

2000 Nissan Altima SE

2000 Nissan Altima SE Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

REMOVAL AND REPLACEMENT

REMOVAL AND REPLACEMENT 2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

Chrysler 2.0L DOHC timing belt procedure REMOVAL

Chrysler 2.0L DOHC timing belt procedure REMOVAL Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1992 and earlier model years, the manufacturer recommends the belt be replaced every 60,000 miles. For 1993-95

More information

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3. 1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling

More information

1998 Honda Accord EX

1998 Honda Accord EX Installation (New Belt) 1. Ensure that engine is at TDC. Align dimple on timing belt drive pulley with pointer on oil pump. See Fig. 4. Align camshaft pulleys with pointers on back covers. 2. Remove battery

More information

Page 1 of 5 Service Manual: TIMING BELT REPLACEMENT - 3.2L & 3.5L REMOVAL & INSTALLATION 1999 Chrysler 300M 3.5L Eng Question: Is a 3.5 a valve bender? - My Autodata book says every car is bender REMOVAL

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page

More information

1999 Nissan Altima GLE

1999 Nissan Altima GLE TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure

More information

VALVE TIMING CHECK-TIMING BELT COVER INSTALLED

VALVE TIMING CHECK-TIMING BELT COVER INSTALLED TIMING BELT SERVICE VALVE TIMING CHECK-TIMING BELT COVER INSTALLED 1. Remove number one spark plug. 2. Using a dial indicator; set number one cylinder to TDC on the compression stroke. 3. Remove the access

More information

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.

More information

2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum

2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum 1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to

More information

ENGINE OVERHAUL <2.4L ENGINE>

ENGINE OVERHAUL <2.4L ENGINE> 11B-1 GROUP 11B ENGINE OVERHAUL CONTENTS SPECIAL TOOLS 11B-2 GENERATOR AND IGNITION SYSTEM 11B-6 REMOVAL AND INSTALLATION 11B-6 EXHAUST MANIFOLD 11B-9 REMOVAL AND INSTALLATION 11B-9 TIMING

More information

Timing Belt: Service and Repair TIMING BELT

Timing Belt: Service and Repair TIMING BELT 2008 Hyundai Accent L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT EMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover. 2. Remove

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT 1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and

More information

2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1

2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove

More information

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. 1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

1 of 10 2/10/2017 5:20 PM

1 of 10 2/10/2017 5:20 PM 1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000

More information

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only

More information

Remove four nuts, then the cooling fan assembly.

Remove four nuts, then the cooling fan assembly. The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.

More information

Timing Belt: Service and Repair TIMING BELT

Timing Belt: Service and Repair TIMING BELT 2003 Hyundai Truck Santa Fe V6-2.7L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT TIMING BELT 2.7L REMOVAL 1. Remove the engine cover. 2. Using a [16 mm], rotate the

More information

1998 Volkswagen Golf GL

1998 Volkswagen Golf GL Removal (Thermo Tensioner Roller - 1997 & Up) CAUTION: To prevent valves from contacting piston, DO NOT rotate camshaft or crankshaft with timing belt removed. Valve damage may result. 1. Remove air cleaner

More information

14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE

14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE 14-6 RADIATOR CAP DRAIN PLUG ENGINE COOLING ON-VEHICLE SERVICE When removing the radiator cap, use care to avoid contact with hot coolant or steam Place a shop towel over the cap and turn the cap counterclockwise

More information

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be

More information

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks

More information

TIMING BELT TIMING BELT

TIMING BELT TIMING BELT TIMING BELT TIMING BELT DISASSEMBLY 1. Lift the vehicle by using of jack. 2. Remove the engine support bracket. (14 mm bolt and 2 nuts, 17 mm bolt) 3. Remove the power steering belt. 4. Remove the air

More information

1998 Subaru Forester

1998 Subaru Forester Inspection 1. Inspect timing belt teeth for breaks, cracks or wear. Inspect belt for signs of oil contamination. When inspecting timing belt, do not bend less than a radius of 2.36" (6.0 mm). Replace belt

More information

1992 Toyota Cressida

1992 Toyota Cressida Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May

More information

ENGINE OVERHAUL GROUP 11B 11B-1 CONTENTS ROCKER ARMS AND CAMSHAFT.. 11B-29 SPECIAL TOOLS... 11B-2 GENERATOR AND IGNITION SYSTEM...

ENGINE OVERHAUL GROUP 11B 11B-1 CONTENTS ROCKER ARMS AND CAMSHAFT.. 11B-29 SPECIAL TOOLS... 11B-2 GENERATOR AND IGNITION SYSTEM... 11B-1 GROUP 11B CONTENTS SPECIAL TOOLS 11B-2 GENERATOR AND IGNITION SYSTEM 11B-5 REMOVAL AND INSTALLATION 11B-5 SOLENOID AND VACUUM HOSE 11B-6 REMOVAL AND INSTALLATION 11B-6 TIMING BELT 11B-7 REMOVAL AND

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

15.Timing Belt. Timing Belt A: REMOVAL ME(STI) TIMING BELT

15.Timing Belt. Timing Belt A: REMOVAL ME(STI) TIMING BELT 15.Timing Belt A: REMOVAL NOTE: Perform the work with the engine installed to body when replacing a single part. For operation procedures, refer to Timing Belt in the PM section.

More information

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) 1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

TIMING BELT/CHAIN AND SPROCKETS

TIMING BELT/CHAIN AND SPROCKETS 9-82 ENGINE 4.7L DN TIMING BELT / CHAIN COVER(S) (Continued) Fig. 130 Accessory Drive Belt Tensioner 1 - TENSIONER ASSEMBLY 2 - FASTENER TENSIONER TO FRONT COVER Fig. 132 Timing Chain Cover Fasteners (4)

More information

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove

More information

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:

More information

Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L

Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

Timing Chain: Service and Repair

Timing Chain: Service and Repair 2005 Nissan-Datsun Altima L4-2.5L (QR25DE) Copyright 2013, ALLDATA 10.52SS Page 1 Timing Chain: Service and Repair TIMING CHAIN Removal and Installation Apply new engine oil to parts marked in illustration

More information

Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

ENGINE 4D68 CONTENTS GENERAL INFORMATION SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS

ENGINE 4D68 CONTENTS GENERAL INFORMATION SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS 11A-0-1 ENGINE 4D68 CONTENTS GENERAL INFORMATION... 11A-0-3 1. SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS......... NEW TIGHTENING METHOD - BY USE OF BOLTS

More information

ENGINE OVERHAUL <3.8L ENGINE>

ENGINE OVERHAUL <3.8L ENGINE> 11D-1 GROUP 11D ENGINE OVERHAUL CONTENTS SPECIAL TOOLS 11D-2 GENERATOR AND DRIVE BELT 11D-4 REMOVAL AND INSTALLATION 11D-4 INTAKE MANIFOLD PLENUM AND THROTTLE BODY ASSEMBLY 11D-6 REMOVAL AND

More information

TIMING CHAINS & BELTS

TIMING CHAINS & BELTS TIMING CHAINS & BELTS * PLEASE READ THIS FIRST * TIMING CHAINS Timing chains will stretch during operation. Limits are placed upon amount of stretch before replacement is required. Timing chain stretch

More information

15.Timing Belt. Timing Belt A: REMOVAL ME(H4DOTC) TIMING BELT

15.Timing Belt. Timing Belt A: REMOVAL ME(H4DOTC) TIMING BELT 15. A: REMOVAL 1. TIMING BELT 1) Remove the V-belts. 2) Remove the crank pulley. 3) Remove the timing belt cover.

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

REMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a).

REMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a). 1 of 25 12/11/2012 4:43 PM REMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover(a). 2. 3. Remove the RH front wheel. Remove the 2 bolts(b) and RH side cover(a). 2 of 25

More information

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300 Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.

More information

5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.

5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose. Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.

More information

CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.

CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly. Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

11A-1 ENGINE CONTENTS ENGINE <4G9>...

11A-1 ENGINE CONTENTS ENGINE <4G9>... 11A-1 ENGINE CONTENTS 11109000276 ENGINE ... ENGINE ... 11A 11B 11A-2 ENGINE CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANTS... 4 SPECIAL TOOLS... 5 ON-VEHICLE SERVICE...

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information