Timing Belt: Service and Repair Timing Belt Replacement
|
|
- Angel Ashlyn Norman
- 6 years ago
- Views:
Transcription
1 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft using the J until the #1 cylinder is at 60 degrees before top dead center (BTDC). 3. Install the J Crankshaft Locking Tool. 4. Rotate the crankshaft in the engine rotational direction (clockwise) using the J until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange. Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover. 5. Install the 1-2 and 3-4 camshaft locks, the J Timing Belt Alignment Kit and the J Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J and J ). Do not rotate the camshafts unless the crankshaft is at 60 degrees BTDC or the valves may contact the crankshaft. 6. Loosen the tensioner pulley. 7. Remove the timing belt. Installation Procedure
2 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 2 1. Position crank at 60 degrees before TDC. Notice: Refer to Fastener Notice in Cautions and Notices. 2. Install the lower idler pulley. Tighten the lower idler pulley bolt to 40 Nm (30 ft. lbs.) 3. Install the upper idler pulley and hand tighten bolt.
3 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 3 Important: With the camshaft locks installed, verify the distance between the camshaft sprockets with the Green Test Belt located in the Timing Belt Alignment Kit J Install the timing belt tensioner and hand tighten nut and washer. 5. Start #1 and #2 camshaft sprockets, route belt around #1 and #2 sprockets while aligning belt marks to marks on the sprocket and rear cover. 6. Install the belt around the timing belt tensioner. 7. Route belt around upper idler pulley. 8. Route belt around #3 and #4 camshaft sprockets while aligning belt marks to marks on sprockets and rear cover. 9. Route belt around crankshaft hub sprockets while aligning marks on belt to marks on the crankshaft hub sprocket. 10. Install the wedge tool J to lock the timing belt onto crankshaft hub sprocket. 11. With belt firmly engaged on crankshaft hub, carefully rotate the crankshaft counterclockwise to get belt slack on lower idler pulley side. 12. Route belt around the lower idler pulley.
4 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page Remove the wedge tool J Re-install the crankshaft locking tool J and tighten the lever arm to the water pump pulley flange. 15. Perform the following in sequence: A. Install the camshaft checking gage to cams 3 and 4 and verify alignment marks are within 2 mm of each other. B. Install 3 and 4 camshaft locks if properly aligned. C. Install camshaft checking gage to cams 1 and 2. D. Rotate #1 camshaft sprocket counterclockwise to remove slack between 1 and 2, and 3 and 4 cams. Important: Ensure that the camshaft timing marks are to the left (retard) side of the checking gage. E. Rotate the upper idler pulley counterclockwise until the marks are properly aligned within 2 mm of each other. F. Install 1 and 2 camshaft locks when properly aligned. Tighten the idler pulley bolt to 40 Nm (30 ft. lbs.)
5 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page Adjust the timing belt tensioner that the center alignment mark is approximately 3mm (1/8 inch) above the alignment on the spring loaded idler. 17. Remove the 1 and 2 and 3 and 4 camshaft locks. 18. Remove the timing belt kit J and J Remove the crankshaft locking tool J Important: If the TDC is passed, do not rotate the crankshaft counterclockwise. This will not allow proper slack to be taken up between the timing belt tensioner and crankshaft sprocket. To correct, rotate the crankshaft two additional turns. 20. Rotate the crankshaft 1 3/4 turns clockwise, install the crankshaft locking tool J , and stop at TDC.
6 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page Tighten lever arm to the water pump pulley flange. 22. Install the checking gage J and verify the marks are 2 mm of each other. 23. Adjust the timing belt tensioner that the center alignment mark is approximately 3 mm above the alignment mark on the spring loaded idler and tighten the timing belt tensioner nut. Tighten the timing belt tensioner nut to 20 Nm (15 ft. lbs.) 24. Remove the crankshaft locking tool J and the checking gage J Install the front timing belt cover. 26. Lower the vehicle. 27. Install the air cleaner assembly. 28. Connect the negative battery cable. Tighten the battery terminal bolt to 17 Nm (13 ft. lbs.)
2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationTiming Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationTIMING BELT REPLACEMENT. Removal Procedure. Tools Required J Timing Belt Alignment Kit J Crank Hub Torx Socket
1 of 15 3/19/2012 5:34 PM TIMING BELT REPLACEMENT Removal Procedure Tools Required J 42069 Timing Belt Alignment Kit J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationRecommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
More informationATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More information2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page
More informationRECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationRecommended Installation Procedure (31 MARCH 2010) ATech Timing Belt Tensioner (979004) EA T 20 Valve Longitudinal Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More information- 1/7 - Copyright Litens Automotive Group All rights reserved.
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure ATech Timing Belt Tensioner and AUDI 2.0L 4V FSI & TFSI Engine (19 January 2015)
The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must be installed
More informationRecommended Installation Procedure ATech Timing Belt Tensioner DaimlerChrysler PL, PT, JR 2.0L 4-Cyl. Engine (10/27/2003)
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to DAIMLERCHRYSLER PL s guidelines. The mounting of the TBT
More informationTiming Belt: Service and Repair
1996 Honda Accord Sedan L4-2.2L SOHC (16 Valve) Copyright 2009, ALLDATA 9.90 Page 1 Timing Belt: Service and Repair TIMING BELT AND TIMING BALANCER BELT REMOVAL Timing Components NOTE: - Turn the crankshaft
More information2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More informationChrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
More informationGM 4-Cylinder Cam Tool Set Operating Instructions
GM 4-Cylinder Cam Tool Set Operating Instructions Cam Tool Part No. Page Camshaft Gear Holder... 536174...2 Camshaft Gear Holder... 536176...2 Camshaft Holding Tool... 536172... 14 Camshaft Sprocket Holding
More informationRecommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationATech Timing Belt Tensioner (979572) VM MOTORI 2.5L Diesel, Common Rail Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationService and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
More informationTiming Belt: Service and Repair Removal and Installation Removal
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Removal and Installation Removal 1. Turn the crankshaft so its white mark (A) lines up with the
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
More informationTIMING BELT TENSIONER FOR AFTERMARKET RENAULT G8T 2.2L DIESEL ENGINE (Revision date: 06/24/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.
More information3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure
2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation.
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationRemoval. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
More informationRecommended Installation Procedure (25 MAY 07) ATech Timing Belt Tensioner (979778) FIAT FIRE 8-valve 1.2/1.4L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More information3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]
1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove
More informationRemoval Procedure. Remove the timing chain tensioner. 1 of 32 12/17/ :42 AM
1 of 32 12/17/2011 11:42 AM Removal Procedure 1. 2. 3. 4. 5. 6. Remove the camshaft cover. Raise and support the vehicle. Remove the No. 1 cylinder spark plug. Rotate the crankshaft in the engine rotational
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More information5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More information1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
More informationREMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More information2001 Escort Workshop Manual
Page 1 of 6 SECTION 303-01B: Engine 2.0L Zetec 2001 Escort Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/26/2004 Timing Drive Components Timing Belt Special Tool(s) Crankshaft TDC Timing
More informationDISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY DISCONNECT CAM POSITION SENSOR CONNECTOR
1 of 12 4/26/2008 1:50 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1987 Toyota Supra L6-3.0L DOHC Turbo (7M-GTE) Conversion
More informationREMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationREMOVAL AND INSTALLATION
2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft
More informationENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal
ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1992 and earlier model years, the manufacturer recommends the belt be replaced every 60,000 miles. For 1993-95
More informationCAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.
CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.4L) Document ID# 2133175 Camshaft Timing Chain, Sprocket, and Tensioner
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationStatic Injection Timing
Page 1 of 13 006-025 Static Injection Timing General Information The static timing is relative to the amount of push tube travel remaining when the piston is 5.161 mm [0.2032 in], or 19 degrees before
More informationPage 1 of 11 Assembly 50. Install the timing chain guide. Tighten to 12 Nm. Page 2 of 11 51. Install the crankshaft sprocket. 52. Install the chain tensioning tool 303-532 to the exhaust camshaft sprocket.
More informationService and Repair. Material. Timing chain
ALLDATA Online - 1999 Mercury Cougar V6-153 2.5L DOHC VIN L SFI - Service and... Page 1 of 16 Service and Repair Notes Material Timing chain 1. Remove and discard the camshaft seal. 2. Remove the engine
More informationService and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
More informationRemove four nuts, then the cooling fan assembly.
The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More information2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
More information11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX
2010 Edge Report a problem with this article 303-03 Engine Cooling 2010 Edge, MKX REMOVAL AND INSTALLATION Procedure revision date: 10/04/2010 Coolant Pump Special Tool(s) Camshaft Holding Tool 303-1248
More informationTiming Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.
Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,
More information2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
More informationTIMING BELT REMOVAL - TIMING BELT
2004 Chrysler Concorde V6-3.5L VIN M Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Procedures TIMING BELT REMOVAL - TIMING BELT CAUTION: The following
More informationCamshaft Timing Chain, Sprocket, And Tensioner Replacement
2007 Pontiac Solstice - Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructi... Page 1 of 29 2007 Pontiac Solstice : Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructions - On Vehicle
More informationTOOTHED DRIVE BELT, REMOVING, INSTALLING AND TENSIONING
2005 Audi A4 Sedan (8E2) L4-1.8L Turbo (AMB) Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Removal and Replacement TOOTHED DRIVE BELT, REMOVING,
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner
More information8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
More informationVALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationTECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
More informationTiming Belt: Service and Repair TIMING BELT
2003 Hyundai Truck Santa Fe V6-2.7L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT TIMING BELT 2.7L REMOVAL 1. Remove the engine cover. 2. Using a [16 mm], rotate the
More informationTiming Drive Components ( )
Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More information15.Timing Chain Assembly
15. A: REMOVAL 1. TIMING CHAIN RH When replacing a single part, perform the work with the engine assembly installed to body. 1) Remove the chain cover. 2) Using
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
More information2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum
1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to
More informationTiming Belt: Service and Repair
2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More informationTiming Belt: Service and Repair Removal
2001 Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Removal Special Tools Required ^ Holder handle 07JAB-001020A ^ Holder attachment,
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationTech Talk. Timing Belt 6VD1/6VE1
Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the
More informationCAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More informationVALVE TIMING CHECK-TIMING BELT COVER INSTALLED
TIMING BELT SERVICE VALVE TIMING CHECK-TIMING BELT COVER INSTALLED 1. Remove number one spark plug. 2. Using a dial indicator; set number one cylinder to TDC on the compression stroke. 3. Remove the access
More information