Tack Distributor Model No. L150,L250, L500 Manual No

Transcription

1 OPERATIONS SERVICES AND PARTS MANUAL Tack Distributor Model No. L50,L50, L500 Manual No. 50

2 Table of Contents Page User's Reference Guide Warranty Certificate General Information Warning Information Safety and Informative Decals Tack Distributor L50 Trailer Specifications Tack Distributor L50 Skid Mount Specifications Tack Distributor L50 Trailer Specifications Tack Distributor L50 Skid Mount Specifications Tack Distributor L500 Trailer Specifications Tack Distributor L500 Skid Mount Specifications Major Components Illustration Major Components Explanation Major Components Explanation Pre-start Information Operation of Tack Distributor Operation of Spray Wand and Spray Bar Parts Information Major Wear Parts TACK DISTRIBUTOR

3 Parts [List of Illustrations] Page L50 Trailer Parts L50 Skid Parts L50 Trailer Parts L50 Skid Parts L500 Trailer Parts L500 Skid Parts L50 Hoses L50/L500 Hoses Propane Tank Assembly Engine and Pump Assembly Lower Liquid Asphalt Valve Assembly Selector Valve Assembly Spray Select Valve Assembly, Trailer Spray Select Valve Assembly, Skid Spray Bar Assembly L50 Idler Axle Assembly L50 Axle & Brake Assembly L500 Idler Axle Assembly L50/L500 Axle & Brake Assembly TACK DISTRIBUTOR

4

5 USER'S REFERENCE GUIDE DELIVERY DATE UNIT SERIAL NUMBER ENGINE TYPE ENGINE NUMBER DEALER'S NAME AND ADDRESS PHONE NUMBER EQUIPMENT HOURS SERVICE MANAGER 688 North Highway 6 Denver, North Carolina (70) TACK DISTRIBUTOR 3

6 One Year or 000 Hour LIMITED WARRANTY WARRANTY. If a defect in material or workmanship is found and the authorized dealer is notified during the warranty period, LeeBoy will repair or replace any part or component of the unit or part that fails to conform to the warranty during the warranty period.. The warranty date will begin upon the completion of the warranty form by the initial customer and will expire after twelve () months have passed. The Warranty Card should be filled out within (0) days of delivery of the unit. 3. Engines are warranted by their manufacturers and may have warranty coverage that differs from that of LeeBoy.. Replacement parts furnished by LeeBoy are covered for the remainder of the warranty period applicable to the unit or component in which such parts are installed. 5. LeeBoy has the right to repair any component or part before replacing it with a new part. 6. All new replacement parts purchased by a LeeBoy dealer will carry a six (6) month warranty. Remanufactured parts purchased by a LeeBoy dealer will carry a ninety (90) day warranty. ITEMS NOT COVERED LeeBoy is not responsible for the following:. Charges for travel time, mileage, or overtime.. Charges related to transporting the product to and from the place at which warranty work is performed. 3. Airfreight charges related to transporting repair parts to the place at which warranty work is performed.. All used units or used parts of any kind. 5. Repairs due to normal wear and tear, or brought about by abuse or lack of maintenance of the equipment, except for premature failures, conveyor chains, polytrack pads, and track rails. 6. Attachments not manufactured or installed by LeeBoy. 7. Liability for incidental or consequential damages of any type including, but not limited to lost profits or expenses of acquiring replacement equipment. 8. Miscellaneous charges. LIMITATIONS LeeBoy has no obligation under this warranty for:. Any defects caused by misuse, misapplication, negligence, accident or failure to maintain or use in accordance with the most current operating instructions.. Unauthorized alterations. 3. Defects or failures caused by any replacement parts or attachments not manufactured by or approved by LeeBoy.. Failure to conduct normal maintenance and operating service, including without limitation, providing lubricants, coolant, fuel, tune-ups, inspections or adjustments. 5. Unreasonable delay, as established by LeeBoy, in making the applicable units or parts available upon notification of a service notice ordered by LeeBoy. 6. The warranty responsibility on all engines rests with the respective manufacturer. 7. LeeBoy may have support agreements with some engine manufacturers for warranty and parts support. OTHER WARRANTIES THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED STATUTORY AND IMPLIED WARRANTIES APPLICABLE TO UNITS ENGINES, OR PARTS WITHOUT LIMITATION, ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT OR WARRANTY, OR ALLEGED NEGLIGENCE OR LIABILITY WITHOUT FAULT, SHALL LEEBOY BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOSS OF PROFIT OR REVENUE, COST OF CAPITAL, COST OF SUBSTITUTED EQUIPMENT, FACILITIES OR SERVICES DOWNTIME COSTS, LABOR COSTS OR CLAIMS OF CUSTOMERS, PURCHASERS OR LESSEES FOR SUCH DAMAGES. TACK DISTRIBUTOR

7 General Information Congratulations on your purchase of a LeeBoy Tack Distributor. This manual is designed to help with the operation and service of your new unit. This unit was carefully designed and manufactured to provide years of dependable service. To keep your tack distributor operating efficiently and safely, carefully read the instructions in this manual. If any questions arise concerning this publication or other manuals in regards to the operation and maintenance of this unit, contact our local LeeBoy dealer for the latest available information. Contents of this manual are based on information in effect at the time of publications and are subject to change without notice. 688 North Highway 6 Denver, North Carolina (70) TACK DISTRIBUTOR 5

8 WARNINGS ALL WARNING DECALS MUST BE FOLLOWED. IF YOU DO NOT FOLLOW THE INSTRUCTIONS, ANY MISTAKE YOU MAKE COULD RESULT IN SERIOUS INJURY AND/OR PHYSICAL HARM TO YOU OR OTHERS. DAMAGE TO THE MACHINE IS ALSO POSSIBLE. NEVER DO ANY MAINTENANCE WHILE BURNERS ARE ON OR ENGINE IS RUNNING. ALWAYS SCOTCH/CHOCK TACK DISTRIBUTOR WHEN LEFT UNATTENDED. NEVER LIGHT TACK BURNERS WITH ANYTHING BUT LIGHTER PROVIDED. NEVER USE SEAL COATING UNLESS FIRST CONTACTING DISTRIBUTOR FOR CORRECT SPECIFICATIONS. NEVER USE FIBER BASE SEAL COAT; THIS COULD DAMAGE THE PUMP AND CLOG THE SPRAY WAND. ALWAYS BE EXTREMELY CAREFUL WHEN IGNITING BURNERS WITH THE LIGHTER PROVIDED. MAKE SURE THE LIGHTER IS KEPT AWAY FROM THE FUEL TANK AND OTHER FLAMMABLE MATERIAL. ALWAYS MAINTAIN DECALS ON MACHINE AND REPLACE IF MISSING OR BADLY WORN. ALWAYS MAINTAIN TACK LEVEL AT LEAST 3 INCHES ABOVE BURNER FLUE. NEVER EXCEED TOWING SPEED SET BY CITY, STATE, AND FEDERAL LAWS. FURTHER- MORE, USE LOWER SPEED WHEN TOWING OVER SLIPPERY OR UNEVEN SURFACES. NEVER ALLOW EXCESSIVE TACK TO BUILD UP ON TACK TANK. THE TACK MAY BE ACCIDENTALLY IGNITED. ALWAYS KEEP ALL UNAUTHORIZED PERSONNEL AWAY FROM WORKING TACK DISTRIBUTOR. ANY AUTHORIZED PERSONS SHOULD WEAR PROTECTIVE CLOTHING AND GLASSES. ALWAYS USE A VEHICLE OF ADEQUATE SIZE WHEN TOWING A TACK DISTRIBUTOR. QUICK STOPS MAY NOT BE POSSIBLE WHEN USING AN UNDERSIZED TOWING VEHICLE. NEVER FILL FUEL TANK OR TACK WHILE ENGINE IS RUNNING OR PROPANE BURNERS ARE LIGHTED. NEVER LEAVE TACK DISTRIBUTOR UNATTENDED WHILE HEATING. NEVER REMOVE SPRAY WAND NOZZLE WHILE ENGINE IS RUNNING. 6 TACK DISTRIBUTOR

9 FLAMMABLE 3 TACK PUMP FLUSH DO NOT REMOVE NOZZLE FROM SPRAY WAND WHILE ENGINE IS RUNNING 5 WARNING! KEEP TAR LEVEL 3 ABOVE BURNER IN USE IMPORTANT! USE ONLY EMULSIFIED ASPHALT THAT WILL SPRAY BELOW 90 O F TURN FLUSH VALVE ON BEFORE STARTING ENGINE 9 0 LIQUID ASPHALT OFF ON 0 3 DO NOT OPERATE OR TOW THIS MACHINE WITHOUT FIRST FULLY UNDERSTANDING THE CONTENTS OF THE OPERATIONS MANUAL L500 6 TACK DISTRIBUTOR 7

10 LeeBoy Model L50 Track Distributor (Trailer Specifications) 65 /" /" 7/8" /" 7" 69 3/" Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: /" Width: 3 /" Height: 30 /" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 3 /" Width: 69 3/" Height: 86 3/" Shipping Weight:,60 lbs. Loaded Weight:,50 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton 8 TACK DISTRIBUTOR

11 LeeBoy Model L50 Track Distributor (Skid Mount Specifications) 6" 8" Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: /" Width: 3 /" Height: 30 /" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 6" Width: 8" Height: 76 3/8" Shipping Weight: 900 lbs. Loaded Weight:,60 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton TACK DISTRIBUTOR 9

12 LeeBoy Model L50 Track Distributor (Trailer Specifications) 69 3/8 7/8" 7/8" 8 /" 7" 7" Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: 8 /" Width: /" Height: 3 /" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 0 /" Width: 7" Height: 9 /" Shipping Weight:,00 lbs. Loaded Weight: 3,500 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton 0 TACK DISTRIBUTOR

13 LeeBoy Model L50 Track Distributor (Skid Mount Specifications) 78 3/6" 80 5/8" 7 3/6" 6" 8" Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: 8 /" Width: /" Height: 3 /" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 6" Width: 8" Height: 80 5/8" Shipping Weight:,60 lbs. Loaded Weight: 3,50 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton TACK DISTRIBUTOR

14 LeeBoy Model L500 Track Distributor (Trailer Specifications) 56 3/8 /8 83 7/8 70 / 73 /8 Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: 83 7/8" Width: 8 /" Height: 3" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 5" Width: 73 /8" Height: 7 5/8" Shipping Weight:,700 lbs. Loaded Weight: 6,700 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton TACK DISTRIBUTOR

15 LeeBoy Model L50 Track Distributor (Skid Mount Specifications) 3/8" 6 5/8" 5 7/8" 03" 5 /8" 8 /" Engine: 5 HP Honda gas engine Fill Spout: 0" x 0" Asphalt Pump: Specially designed.308 CI Pump Clean Out: " Heat System: Two () 5,000 BTU Propane burners, one () starter burner and a 30 lb. fuel tank Temperature Gauge: degrees Fahrenheit Tank Dimensions: Length: 83 7/8" Width: 8 /" Height: 3" Flush Tank: Seven (7) gallon Access Valve: Dimensions: Length: 03" Width: 8 /" Height: 6 5/8" Shipping Weight:,700 lbs. Loaded Weight: 6,700 lbs. Optional Equipment: Eight (8) foot spray bar that folds to a lockable position. Hose & Reel: Wand: /" x 0' heavy duty hose with a heavy duty re-coil reel Six (6) foot wand with on/off valve and removable spray tip Separate cut-off valves to control each spray nozzle. 5 HP Briggs & Stratton TACK DISTRIBUTOR 3

16 Major Components 7. PROPANE TANK 6. FILL NECK 5. SPRAY WAND SELECT 6. SPRAY BAR SELECT 3. ENGINE. JACK STAND 8. BURNERS. IGNITER 9. SPRAY WAND. DISTRIBUTOR VALVE. FLUSH TANK. CIRCULATING TANK VALVE 3. THERMOMETER 0. LIQUID ASPHALT VALVE 5. RELIEF VALVE. FLUSH VALVE TACK DISTRIBUTOR

17 MAJOR COMPONENTS. Flush Tank Flush tank contains the fluids used to flush and clean out the pump and system.. Igniter Igniter is used to light the burners for heating. Caution should be used with this because of the gas engine and the fuel in the flush tank. Also, make sure there are no gas flames in the exhaust stacks.! WARNING! WHEN IGNITING BURNERS WITH LIGHTER BE EXTREMELY CAREFUL THAT THE LIGHTER IS KEPT AWAY FROM THE FUEL TANK AND OTHER FLAMMABLE MATERIALS. 3. Engine Engines available on the tack distributor are either Honda or Briggs & Stratton. These are gas engines and clean gas should be used at all times.. Jack Stand Jack stand is used to hook and unhook the unit from the truck. Caution should be used when unhooking unit to make sure wheels are scotched so unit will not roll. 5. Relief Valve Relief valve adjusts pressure of the pump. It is recommended to have the least amount of pressure on the valve to prolong the pump life. Set relief valve pressure on initial start-up. 6. Fill Neck Fill neck is where you fill tack tank. Make sure splash plate is in place. 7. Propane Tank Propane is used to heat tack. The tank pressure should range from eight (8) to ten (0) lbs. of pressure. 8. Burners Right and left burners heat the tack. Before lighting, make sure valves to burners are off. They should be lit with igniter only. Make sure tack level is three (3) inches above burner and unit is sitting level. 9. Spray Wand Spray wand is used to spray tack. It has an on/off ball valve that lets you spray small areas and pavement edges. Care and caution must be used to keep the nozzle clean and the line flushed after each use. WARNING: You should never attempt to clean nozzle out or remove nozzle while machine is running. The line can become pressurized and spray tack on an individual. Hot tack causes harm and/or injury. 0. Liquid Asphalt Valve Liquid asphalt valve allows liquid asphalt to be pumped out of the tank and into the spray wand or spray bar. It must be turned off to flush out the system. The only function of this valve is to retrieve tack from the tank and should be off at all other times.. Distributor Valve Distributor Valve is used to retrieve tack from lines and spraybar.. Circulating Tank Valve Tank valve is used to circulate the tack back into the tank. It must be closed off to force the tack to the spray bars and wand. It must be off while flushing the system. 3. Thermometer Thermometer is used to measure temperature inside the tack tank. Temperature should not exceed 90 deg. (F). TACK DISTRIBUTOR 5

18 (cont'd) MAJOR COMPONENTS.Flush Valve Flush valve is used to allow the flush material to flow out of the flush tank and into pump system. 5.Spray Wand Select Valve Spraywand select valve allows the tack material to flow to spraywand. 6. Spray Bar Select Valve Spraybar select valve allows the flow of material to the spraybar. 6 TACK DISTRIBUTOR

19 PRE START-UP INSPECTION GENERAL OPERATION To assure that the tack distributor provides the best possible service before use, a prestart up inspection should be performed.. Engine (A) Check oil level. (B) Check fuel tank level. (C) Check for any cracked, broken or worn parts.. Tack Tank and Attaching Components (A) Check tack level, fill if needed. (B) Remove contamination on surface. (C) Check spray wand valve to make sure it works freely. (D) Check propane level. (E) Check flow valves to make sure they are working freely. (F) Check flush tank level. (G) Check for cracked, broken or worn parts. (H) Check wheel lugs. (I) Check tire pressure. START-UP GENERAL OPERATION An engine manual is provided with the tack distributor and should be used whenever starting, operating, and servicing engine. TURN FLUSH VALVE ON BEFORE STARTING ENGINE TACK DISTRIBUTOR 7

20 OPERATION OF TACK DISTRIBUTOR Before putting the tack distributor into operation, make sure it has been secured so the unit does not roll or move unintentionally during operation. Follow the procedures below and use good safe operating practices when involved in the operation of the tack distributor.. Make sure all valves are off.. Check asphalt level in tank. It must be at least 3 above flue before lighting burners. 3. Open the valve on the propane tank. Remove the igniter from its stowed position. Open valve on igniter and light.. Regulate the propane pressure to 8 to 0 psi. (max) by adjusting knob on regulator. 5. To light burner, hold igniter flame in front of burner before opening gas valve. Now, light the other burner in the same manner. 6. After burner is lit, bring the liquid asphalt temperature to material specifications. (This should not exceed 90 deg. F or 88 deg. C). 7. Monitor temperature by referring to temperature gauge. 8. Turn flush valve on before starting engine. 9. After asphalt is at specified temperature start engine according to engine manual. 0. Turn off flush valve after engine is running.. Turn liquid asphalt tack on.. Unroll spray wand and spray tack. 3. While spraying, set relief for desired pressure (the least amount of pressure on relief, the longer the life of pump). Spray Wand Select. Spraying Tack: Tack valve should be on. Circulating valve should be closed. Spray Bar Select Distributor valve knob should be pulled out. Select spray bar or spray wand to use while spraying tack. 5. Spray wand selected: Open wand select valve to spray tack. Open valve on wand to spray. 6. Spray bar selected: Open nozzles desired on spray bar. Open and close spray bar select valve for spraying of tack. NOTE: When allowing machine to run for short periods of time without spraying, open circulating valve to relieve excessive pump pressure. 8 TACK DISTRIBUTOR

21 OPERATION OF SPRAY WAND AND SPRAY BAR 7. Back flush: Open circulating valve to let material flow back into tank. Close tack valve at bottom of tank. Push in distributor valve to retrieve material out of hose. 8. Wand: Open spray wand valve and allow 30 seconds before flushing. 9. Spray bar: Open spray bar select valve. Allow 30 seconds then close nozzle valve closest to center of spray bar. Allow 0 seconds then close the next valve towards outside of spray bar. Repeat until all nozzles are flush. Distributor Valve Circulating Valve Flushing spray wand: Close the circulating valve. Close the valve on the wand. Open the wand select. Pull out distributor valve knob. Open flush valve on hose coming out of flush tank. Open valve on wand and flush until you see flush material. Close valve on wand, and shutdown engine. Check all valves on machine to make sure they are all closed. Flushing spray bar: Close the circulating valve on tank. Open spraybar select valve to let material flow to bars. Pull out distributor valve knob. Open flush valve to let flush material go to spray bar. Open all nozzle valves one at a time, until flush material is visible; then close valves. Shut down engine and make sure all valves are shut. 0. Height of the Spray Bar may be adjusted by removing two bolts and raising or lowering the bar to desired height.. Six Spray Nozzles may be turned off or on individually or the entire bar may turned off or on through one valve. NOTE: When moving from one job site to another, turn the individual nozzle valves off to prevent dripping. TACK DISTRIBUTOR 9

22 PARTS INFORMATION In order to expedite locating and shipping of parts you may need, please refer to the following information:. All parts must be ordered by a LeeBoy dealer.. The model and serial number of the unit should be given when ordering parts. 3. Parts should be ordered by part number and description. 688 North Highway 6 Denver, North Carolina (70) TACK DISTRIBUTOR

23 MAJOR WEAR PARTS PART NO. DESCRIPTION 3090 BURNER NOZZLE, TACK TANK, SCREED 3000 BURNER NOZZLE, IGNITER 8000 PUMP, TACK 5050A CPLG. HALF, 5 HP ENGINE 8000 INSERT, 3 JAW CPLG CPLG. HALF, TACK PUMP 8000 VALVE, RELIEF 8090 BALL VALVE, /" 50090A WHEEL-TIRE ASSY., (-50/-500) SEAL KIT, PUMP 300 GAUGE, L.P.G. PRESS DECAL KIT DECAL KIT DECAL KIT 8030 TACK SPRAY NOZZLE 800 HOSE, HOSE REEL 688 North Highway 6 Denver, North Carolina (70) TACK DISTRIBUTOR

24 L50 Trailer , ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 500 ENGINE & PUMP ASSY., (HONDA) SEE PAGE PLUG, " N.P.T JACK STAND WHEEL, 5 LUG TACK TANK, DRAIN PIPING SPRAY BAR ASSY., 8 FT. SEE PAGE BATTERY 859 SPRAY SELECTOR VALVE ASSY., TRAILER SEE PAGE AXLE ASSY., IDLER 3500# SEE PAGE 3 * 5000C AXLE ASSY., BRAKE 3500# (*OPTIONAL) SEE PAGE 35 TACK DISTRIBUTOR

25 L50 Skid , ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 500 ENGINE & PUMP ASSY., (HONDA) SEE PAGE SPRAY SELECTOR VALVE, SKID SEE PAGE BALL VALVE, " BATTERY PLUG, " N.P.T. TACK DISTRIBUTOR 3

26 L50 Trailer , ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 500 ENGINE & PUMP ASSY., (HONDA) SEE PAGE B AXLE ASSY., BRAKE 500# SEE PAGE JACK STAND A WHEEL, 6 LUG TACK TANK, DRAIN PIPING SPRAY BAR ASSY., 8 FT. SEE PAGE BATTERY 859 SPRAY SELECTOR VALVE ASSY., TRAILER SEE PAGE PLUG, " N.P.T. TACK DISTRIBUTOR

27 L50 Skid , 7 6 ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 500 ENGINE & PUMP ASSY., (HONDA) SEE PAGE SPRAY SELECTOR VALVE, SKID SEE PAGE BALL VALVE, " BATTERY PLUG, " N.P.T. TACK DISTRIBUTOR 5

28 L500 Trailer , ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 800 BALL VALVE, " ENGINE & PUMP ASSY., (HONDA) SEE PAGE SPRAY BAR ASSM, 8' SEE PAGE HEATER, ELECTRIC 0V BATTERY HOSE ASSY., DISTRIBUTOR VALVE TO HOSE REEL HOSE ASSY., DISTRIBUTOR VALVE TO SPRAY BAR 859 SPRAY SELECT VALVE ASSY., TRAILER SEE PAGE 3 500A JACK STAND, TOWING TONGUE 3 500A PINTLE EYE ASSY., TOWING TONGUE 5000 PINTLE EYE B AXLE ASSY., BRAKE 500# SEE PAGE A AXLE ASSY., IDLER 500# SEE PAGE A WHEEL, 6 LUG 6 TACK DISTRIBUTOR

29 L500 Skid , Shown without heater Item 6 used to cap heater port. ITEM NO. QTY. PART NO. DESCRIPTION REFERENCE LOCATION 5000 HOSE REEL ASSY DRAIN PLUG SELECTOR VALVE ASSY. SEE PAGE LOWER LIQUID ASPHALT VALVE ASSY. SEE PAGE PROPANE TANK, 30#, L.P.G TANK ASSY., FLUSH MANIFOLD, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT GAUGE/REGULATOR, L.P.G BURNER NOZZLE, IGNITER GAUGE, TEMPERATURE 8030 WAND, TACK SPRAY BATTERY BOX 500 ENGINE & PUMP ASSY., (HONDA) SEE PAGE BATTERY PLUG, " N.P.T BALL VALVE, " SPRAY SELECT VALVE ASSY., SKID SEE PAGE 3 TACK DISTRIBUTOR 7

30 L50 Hoses Trailer Skid ITEM NO. QTY. PART NO. DESCRIPTION 5006 HOSE ASSY., TANK VALVE RETURN TO LIQUID VALVE 3090 HOSE ASSY., FLUSH VALVE HOSE ASSY., TACK PUMP FEED 5007 HOSE ASSY., RELIEF VALVE TO UPPER TANK VALVE HOSE ASSY., UPPER VALVE TO HOSE REEL (SKID ONLY) ADAPTER, HOSE TO PIPE (SKID ONLY) HOSE, HOSE REEL 8 500A HOSE, SELECTOR VALVE TO HOSE REEL 9 500A HOSE, SELECTOR VALVE TO SPRAY BAR 8 TACK DISTRIBUTOR

31 L50/L500 Hoses Trailer Skid ITEM NO. QTY. PART NO. DESCRIPTION 5006 HOSE ASSY., TANK VALVE RETURN TO LIQUID VALVE 3090 HOSE ASSY., FLUSH VALVE HOSE ASSY., TACK PUMP FEED 5007 HOSE ASSY., RELIEF VALVE TO UPPER TANK VALVE HOSE ASSY., UPPER VALVE TO HOSE REEL (SKID ONLY) ADAPTER, HOSE TO PIPE (SKID ONLY) HOSE, HOSE REEL HOSE, SELECTOR VALVE TO HOSE REEL HOSE, SELECTOR VALVE TO SPRAY BAR TACK DISTRIBUTOR 9

32 Propane Tank Assembly ITEM NO. QTY. PART NO. DESCRIPTION PROPANE TANK, 30#, L.P.G BURNER NOZZLE, TACK TANK, SCREED HEAT BURNER NOZZLE, IGNITER 3000 REGULATOR W/ GAUGE, L.P.G MANIFOLD., L.P.G HOSE ASSY., L.P.G. IGNITER HOSE ASSY., L.P.G. TANK TO REGULATOR HOSE ASSY., L.P.G. MANIFOLD TO BURNER NOZZLE P.O.L. ADAPTOR, L.P.G. TANK COUPLING, /" PIPE VALVE, /" 300 ELBOW, /" F.P.T. x /" M.P.T GAUGE, L.P.G. PRESS. 30 TACK DISTRIBUTOR

33 9 5 Engine & Pump Assembly ITEM NO. QTY. PART NO. DESCRIPTION 5000H ENGINE, HONDA 5HP 5000 ENGINE, BRIGGS & STRATTON 5 HP 5060 ADAPTER, PUMP TO ENGINE A CPLG. HALF, 5 HP ENGINE 8000 INSERT, 3 JAW CPLG CPLG. HALF, TACK PUMP PUMP, TACK NIPPLE, /" x " LG VALVE, RELIEF ADAPTER, PIPE TO HOSE (90 DEG.) ADAPTER, PIPE TO HOSE (TEE) 000A LINE, RELIEF VALVE ADAPTER, PIPE TO HOSE (90 DEG.) SEAL KIT, PUMP * 5000HE ENGINE (OPTIONAL), HONDA 5 HP W/ ELEC. START Lower Liquid Asphalt Valve Assembly 9 7 ITEM NO. QTY. PART NO. DESCRIPTION NIPPLE, " PIPE x CLOSE 8070 ELBOW, "PIPE CROSS, " PIPE 800 BALL VALVE, " BUSHING, HEX HEAD "x /" NIPPLE, /" PIPE x CLOSE BALL VALVE, /" ADAPTER, PIPE TO HOSE ADAPTER, PIPE TO HOSE TACK DISTRIBUTOR 3

34 3 Selector Valve Assembly ITEM NO. QTY. PART NO. DESCRIPTION VALVE, SELECTOR 8070 NIPPLE, /" PIPE x CLOSE BALL VALVE, /" ADAPTER, PIPE TO HOSE TEE, /" PIPE 3 5 Spray Select Valve Assembly, Trailer ITEM NO. QTY. PART NO. DESCRIPTION ELBOW, STREET /" NPT 8090 BALL VALVE, /" ADAPTER, PIPE TO HOSE NIPPLE, /" x 5 /" LG NIPPLE, /" PIPE x CLOSE TEE, /" PIPE 3 Spray Select Valve Assembly, Skid 5 3 ITEM NO. QTY. PART NO. DESCRIPTION NIPPLE, /" PIPE x CLOSE 800 TEE, /" PIPE ELBOW, STREET /" NPT 8090 BALL VALVE, /" ADAPTER, PIPE TO HOSE TACK DISTRIBUTOR

35 Spray Bar Assembly ITEM NO. QTY. PART NO. DESCRIPTION MOUNTING ASSY., SPRAY BAR 8598 SPACER, SPRAY BAR ARM ARM, SPRAY BAR ARM 8593 SPRAY BAR, MOUNTING BRKT MANIFOLD NUT, FRICTION PIN, CLEVIS TEE, " 3000# SCH PLUG, " PIPE BUSHING, " M.P.T. x /" F.P.T NIPPLE, /" PIPE x CLOSE BALL VALVE, / " BUSHING, /" M.P.T. x /" F.P.T NOZZLE, TACK SPRAY NIPPLE, " PIPE x 8" LONG ADAPTER ELBOW, PIPE TO HOSE HOSE ASSY., MANIFOLD TO L.H. ARM HOSE ASSY., MANIFOLD TO R.H. ARM CLIP, CLEVIS PIN TACK DISTRIBUTOR 33

36 L50 Idler Axle Assembly 8 6, 5 9 0, 7, 3 3, 5 ITEM NO. QTY. PART NO. DESCRIPTION 5000 AXLE ASSY., IDLER 3500# WHEEL HUB ASSY., 3500# CUP, ROLLER BEARING 5080 CONE, ROLLER BEARING CUP, ROLLER BEARING CONE, ROLLER BEARING WHEEL STUD WHEEL SEAL, 3500# GREASE CAP, 3500# LUG NUT SPRING, AXLE U-BOLT KIT, 3500# HEX CROWN AXLE NUT D-HOLE FLAT WASHER LOCKWASHER ITEM INCLUDES ITEMS 3 THRU 0. 3 TACK DISTRIBUTOR

37 L50 Axle & Brake Assembly , ITEM NO. QTY. PART NO. DESCRIPTION 8, 5 8, C AXLE ASSY., BRAKE 3500# 5050 BRAKE DRUM ASSY., 3500# CUP, ROLLER BEARING 5080 CONE, ROLLER BEARING WHEEL STUD WHEEL SEAL 3500# GREASE CAP 3500# LUG NUT CUP, ROLLER BEARING CONE, ROLLER BEARING 5060R BRAKE ASSEMBLY 3500R 5060L BRAKE ASSEMBLY 3500L BRAKE SHOE KIT x 300A BRAKE ADJUSTER ELECTRO-MAGNET SPRING, AXLE 3500# U-BOLT KIT 3500# AXLE NUT D-WASHER LOCKWASHER 3030 SPRING KIT 300B SPRING ITEM INCLUDES ITEMS 3 THRU 0. ITEM INCLUDES ITEMS 3 THRU 5. ITEM INCLUDES ITEMS 3 THRU 5. TACK DISTRIBUTOR 35

38 L500 Idler Axle Assembly 8 3, 9 0, 7 6, 5 5, 3 ITEM NO. QTY. PART NO. DESCRIPTION 5000A AXLE ASSY., IDLER 500# 600 WHEEL HUB ASSY., 500# CUP, ROLLER BEARING 600 CONE, ROLLER BEARING CUP, ROLLER BEARING CONE, ROLLER BEARING WHEEL STUD WHEEL SEAL 500# GREASE CAP 500# LUG NUT 50060A SPRING, AXLE 500# 50050A U-BOLT KIT 500# HEX CROWN AXLE NUT D-WASHER LOCKWASHER ITEM INCLUDES ITEMS 3 THRU TACK DISTRIBUTOR

39 L50/L500 Axle & Brake Assembly 6 9, , ITEM NO. QTY. PART NO. DESCRIPTION 8, 5 8, B AXLE ASSY., BRAKE 500# BRAKE DRUM ASSY., 500# CUP, ROLLER BEARING 600 CONE, ROLLER BEARING WHEEL STUD WHEEL SEAL 500# GREASE CAP 500# LUG NUT CUP, ROLLER BEARING CONE, ROLLER BEARING 30060R BRAKE ASSEMBLY 500R 30060L BRAKE ASSEMBLY 500L A BRAKE SHOE KIT x 30 0-A BRAKE ADJUSTER ELECTRO-MAGNET A SPRING, AXLE 500# A U-BOLT KIT 500# AXLE NUT D-WASHER LOCKWASHER 3030 SPRING KIT 300B SPRING ITEM INCLUDES ITEMS 3 THRU 0. ITEM INCLUDES ITEMS 3 THRU 5. ITEM INCLUDES ITEMS 3 THRU 5. TACK DISTRIBUTOR 37

40 Other Members of the LeeBoy Family of Products... 85OO Elite II Ashpalt Paver 685 Motor Grader O Pneumatic Roller 80OO Ashpalt Paver 00 Vibratory Roller 00S Maintainer 688 North Highway 6 Denver, North Carolina (70) 83-97