Made in GERMANY. Spray nozzles and lube points
|
|
- Gavin Williamson
- 6 years ago
- Views:
Transcription
1 Lubrication Systems Made in GERMANY Lubricants Spray nozzles and lube points
2 Spray pattern Spray pattern Control air, spray air (swirl air), compressed air and oil Dot, circle, ellipse Spray pattern 1 spray pattern without spray air (swirl air) Dot the typical spray pattern of a nozzle is composed of a core stream and a diffuse edge stream of the lubricant the relation between core stream and diffuse edge stream, as well as the overlap of the applied lubricant onto the sheet material depends on the used lubricant as well as the pre-set pressure ratios between spray air (swirl air) and the air jet for the wide pattern of the lubricant 1 the control air closes or opens the nozzle, using a nozzle needle 2 the spray air (swirl air) converts the solid lubricant stream into extreme particular droplets 3 the wide, compressed air stream, directs the lubricant drops from the circular spray pattern to an elliptical spray pattern 2 spraying pattern with spray air (swirl air) Circle Compressed air pressure parameter high pressure low pressure spray air (swirl air) the wide, compressed air stream small drop size oil mist formation fine distribution much larger central spray area than the periphery spray area elliptical lubrication pattern large drop size nearly no oil mist creation corse distribution larger central spray area periphery spray area circular lubrication pattern 3 spraying pattern with wide angle air Ellipse oil large lubricant quantity small lubricant quantity 2 3
3 Raziol overview Raziol overview Overview Raziol nozzles and lube points for the use with Raziol control units for tool lubrication and for minimal lubrication at the non-cutting forming eg. deep drawing, stamping, bending, profiling, thread forming; as well as for the cutting processes eg. drilling, milling, turning ST DUSTY-2000 Lube point DUSTY-2000 ST LAMA-1000 Lube points LAMA-1000 ST CD-100 BS (D) Lube point CD-100 wide jet air (throttle) ST LAMA-3000 Lube points LAMA-3000 ST CD 95/105 Lube point CD 95/105 ST LAMA-4000 Lube points LAMA-4000 BS-25/ SV block nozzle-25/ grinding hole pilot valve 4 5
4 ST LAMA-1000 ST LAMA-1000 Lube point ST LAMA-1000 Lubricating station ST LAMA-1000 ca. 70 ca. 120 ca. 120 ST LAMA-1000/ Scatter precision coaxial spray head with magnetic stand for the positioning of the spray jet minimal possible application amount (or quantities) < 0,05g/signal for highly viscous lubricants interchangeable nozzle inserts with different set points for variable lubrication quantities and viscosities the lubrication point ST LAMA-1000 HL and HL scatter is equipped with a high performance nozzle (HL) that is specially designed for the task where the to be formed parts can be lubricated over a larger distance and with a fast succession of lubrication cycles. 42 ST LAMA-1000/Scatter ST LAMA-1000 HL ST LAMA-1000 HL Scatter ST LAMA-1000/ Scatter ca. 90 ST LAMA-1000 HL ca. 112 ST LAMA-1000 HL Scatter precision coaxial spray head with circular jet spray angle and nozzle opening of Ø 0,4-1,5 mm complete with 3m hose package, screws and fittings 8/6mm, 1/4 and double hinged holder with magnetic foot Ø 63mm complete with magnetic valve for control air, magnetic coil with connecting cable and RVplug, complete with 3m hose package, screws and fittings 8/6mm, 1/4 and double hinged holder with magnetic foot Ø 63mm complete with one magnetic valve for control air, magnetic coil with connecting cable and RV-plug, complete with 3m hose package, screws and fittings 8/6mm, 1/4 and double hinged holder with magnetic foot Ø 63mm part no connections lubricant x (white) x (white) x (white) spray air (swirl air) x (black) - x (black) ST LAMA-1000 HL ST LAMA-1000 HL Scatter control air x (blue) x (blue) x (blue) 6 7
5 ST LAMA-3000 ST LAMA-3000 Lube point ST LAMA-3000 Extensions precision coaxial spray head with magnetic stand for the positioning of the spray jet minimal possible application amount (or quantities) < 0,05g/signal low to medium viscosity precision spray head attachment with different lengths available (40 mm up to 800 mm), circular spray pattern wide angle spray attachable precision spray head extension available, in different lengths (50-800mm) LAMA 3000/VL-100 L L LAMA 3000 extension, wide angle attachment d = 4 mm LAMA 3000 extension ST LAMA-3000/ VL -200 part no connections 3 lubricant x (white) ST LAMA-3000 precision coaxial spray head with 5 circular jet spray head separated connections for spray and control air with complete with 3m hose package, screws and fittings and double hinged holder with magnetic foot Ø 63mm spraying angle 90, spraying pattern in an eliptical shape the extension tube of the spray head extension is bendable and can therfore be positioned to the exact lubrication point precision spray head extension wide angle precision spray head extension length L [mm] part no. part no spray air x (red) (swirl air) control air x (blue) ST LAMA
6 ST LAMA-4000 ST LAMA-4000 Lube point LAMA-4000 Lubricating station LAMA-4000 L precision coaxial spray head with magnetic base for exact positioning of the spray jet minimal possible application quantity < 0,05 g/signal for low to medium viscosity lubricants different spray nozzle attachments to obtain distinctive lubrication patterns several coaxial spray heads with various orifice sizes available, to be used for the different needs in lubrication volume and viscosities ST LAMA ca. 16 ST LAMA-4000 d = 8 mm LAMA attachment, circular spray pattern 75 d = 4 mm LAMA-4000 extension d = 13 mm LAMA attachment, wide angle spray pattern 90 with nozzle precision coaxial spray head with 5 circular spray angle and nozzle opening Ø 0,3 mm complete with 3m hose package, fittings and double hinged holder with magnetic foot Ø 63mm L ST LAMA-4000 part no connections 3 lubricant x (white) spray air (swirl air) x (red) control air x (blue) length L [mm] extension Circular spray LAMA-4000 with wide angle jet for LAMA-4000 with equipment for 75 L=40mm coil strip lubrication inside pipe lubrication wide angle spray part no Circular spray 75 L=20mm attachment part no
7 ST DUSTY-2000 ST DUSTY-2000 Lube point DUSTY-2000 Lube point DUSTY-2000 ca. 70 circular spray nozzle ST-Dusty-2000 precision coaxial spray head with 15 circular spray angle the lubricant quantity and the spray air (swirl air) are directly adjustable at the spray head left turn: more lubricant, more spray air (swirl air) right turn: less lubricant, less spray air (swirl air) attachable precision spray head extension available, in different lengths (50-800mm) diameter of the extension 4 mm, at the tip 5 mm ST DUSTY circular spray nozzle with an extension ST DUSTY-2000/ VL-200 the extension tube of the spray head extension is bendable and can therfore be positioned to the exact lubricated point. ST DUSTY-2000 ST DUSTY-2000/VL-200 precision coaxial spray head with 15 circular spray angle, with combined connection for the spray and control air. Complete with 3m hose package, fittings and double hinged holder with magnetic foot Ø 63mm with 200 mm spray head extension part no connections 2 2 lubricant x (white) x (white) control air x (blue) x (blue) 12 ST-Dusty-2000/VL
8 ST CD-100 BS (D) ST CD-100 BS (D) Lube point CD-100 wide angle jet (air regulator) Lube point CD-100 wide angle spray attachment St block nozzle CD-100 BS precision coaxial spray head with 90 wide angle jet for the use in spraying lubrication very good setting of the spraying parameter very good reproducibility of the applicable lubricant the spray air activates the nozzle the elliptical lubrication pattern is achieved using the wide angle spray attachment the lubrication width of the nozzle can be modified by adjusting the pressure setting on the wide angle spray attachment St block nozzle CD-100 BS block nozzle ST CD-100 BS St block nozzle CD-100 BS block nozzle ST CD-100 BSD precision coaxial spray head with 90 flat jet spray angle and manual lubricant quantity adjustment via a precision raster regulator with 40 raster settings per turn combined spray and wide angle jet complete with 3m hose package, fittings and dual manetic holder with magnetic foot Ø 63mm part no connections 4 3 lubricant x (white) x (white) spray air x (black) (swirl air) control air x (blue) x (blue) wide angle jet x (yellow) x (yellow) nozzle part no. CD-100 BS CD-100 BSD St block nozzle CD-100 BS 14 15
9 ST CD-95/105 ST CD-95/105 Lube point CD 95/105 Lube point CD 95/105 21,5 17,5 ST CD 95 precision coaxial spray head with 90 flat angle jet for the use in spraying lubrication very good setting of the spraying parameter very good reproducibility of the applicable lubricant the control air operates the nozzle complete as lubrication point with 3 m hose package and double magnetic holder with magnetic foot Ø 63 mm for the use in spraying chambers, mounted as a nozzle bar minimal installation dimensions ca ,5 ca. 26 block nozzle CD 95 block nozzle CD 105 block nozzle CD 95 block nozzle CD 105 nozzle opening part no. precision coaxial spray head with 90 flat angle jet for the use in spraying lubrication Ø 0,5/1,0/1,5 mm and lock connection to regulate the amount of oil (nozzle opening 0,5 mm) (nozzle opening 1,0 mm) (nozzle opening 1,5 mm) Ø 0,5 mm and lock connection to regulate the amount of oil (nozzle opening 0,5 mm) connections 3 3 lubricant x (M) x (M) spray air (swirl air) x (Z) x (Z) control air x (S) x (S) ST CD
10 BS-25/ SV BS-25/ SV Block nozzle-25/ grinding hole pilot valve Block nozzle-25/ grinding hole pilot valve BS-25/ SV manual grid/ pilot valve BS-25/ SV atomatic grid/ pilot valve block nozzle with manual or automatic lubricant quantity adjustment very good reproducibility of the applicable lubricant very fast response time the control air operates the nozzle the flattening of the cyrcling spray pattern of the nozzle will be implemented by the wide angle jet the pressure of the wide angle jet can influence the lubrication width of each nozzle for the use in spraying chambers and nozzle bars lubrication of blanks and coil strip material full surface, sectoral and partial lubrication possible drive by pulse width modulation possible medium (lubricant) wide angle jet wide angle attachment spray air (swirl air) BS-25/ SV manual grid/pilot valve single BS-25/ SV atomatic grid/ pilot valve single knurled screw control air pilot valve BS-25/ SV manual swirl/ pilot valve single block nozzle with manual oil amount setting with a precision grid nozzle M6x0,5 with 40 grid positions per revolution with wide spray attachment, pilot valve and consistent oil bore (grinding hole) with wide spray attachment, pilot valve and consistent oil bore (grinding hole) with internal twist nozzle, pilot valve and continuous oil bore (grinding hole) part no connections lubricant x x x spray air x x x (swirl air) control air x x x wide angle jet x x return flow of x the lubricant BS-25/ SV manual swirl/ 18 pilot valve 19
11 HE Hagener Straße D ISERLOHN GERMANY Phone: Fax: info@raziol.de Web:
Spray chamber system SKT-B
Zibulla & Sohn GmbH Made in Germany Razio Basic Line Spray chamber system SKT-B user-friendly reproducible lubricant application minimal space requirements Spray chamber system Basic Line Spray chamber
More informationCompany history Commencement of the Managing Director Georg Zibulla senior; the newly introduced product name RAZIOL becomes the quality term
2 3 RAZIOL products at a glance RAZIOL products at a glance The following pages of this company brochure contain a brief overview of the RAZIOL company history as well as the current spectrum of products.
More informationRaziol Oil mist and Emulsion mist extraction units. Quality from the Market Leader
Raziol Oil mist and Emulsion mist extraction units Lubrication Systems Quality from the Market Leader Lubricants Raziol Oil mist and Emulsion mist extraction units 1 www.raziol.com Table of Contents Page
More informationRaziol Dosing Control Units Contact Lubrication. Quality from the Market Leader
Raziol Dosing Control Units Contact Lubrication Lubrication Systems Quality from the Market Leader Lubricants Raziol Dosing Control Units Contact Lubrication 1 www.raziol.com Table of Contents Page Manual
More informationSKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B EN
SKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B 1-4402-EN Spray blocks Every spraying unit is connected to the coaxial outlet of a VTEC or VE1B unit. It
More informationVECTOLUB Minimal Quantity Lubrication
VECTOLUB Minimal Quantity Lubrication 1-5012-2-US for tools and dies VECTOLUB 1 VECTOLUB 2 VECTOLUB 3 External minimal quantity lubrication (MQL) VOGEL MQL pays off, because the workpiece and environment
More informationAutoJet Lubrication Systems
AutoJet Lubrication Systems AutoJet Lubrication Systems AutoJet Lubrication Systems provide a highly efficient method of applying lubricants and corrosion protection fluids. In addition to lubricating
More informationAutoJet. Highly efficient method of applying lubricants and corrosion protection fluids
AutoJet Lubrication Systems Highly efficient method of applying lubricants and corrosion protection fluids Functional Differences Nozzles for Type P400: Type L210 For low-viscosity media Type P400 For
More informationMarking Systems. Paint Spray Systems Marking Blocks Paints & Inks
Marking Systems Paint Spray Systems Marking Blocks Paints & Inks Various Applications Usage and Setup Flexibility Precise edging and maximum reproducibility with virtually zero overspray. Automated Dot
More informationHollow Cone Nozzles. The H series nozzle option diverts flow at a right angle without an internal vane, thereby reducing the risk of blockage.
lower energy ring of spray useful for low flow, low impact applications. The internal geometry swirls fluid into a circular ring spray pattern. tomisation occurs at low pressures. The H series nozzle option
More informationLances and nozzle headers
Sanitary Retractable Lances Standard Flanged Lances Tank Cleaning Lances STAMM Showers Pneumatic Atomizing Air Blowoff Quick Disconnect Flat Fan Plastic Specialty 141 Lances Custom fabricated for your
More informationSKF VectoLub, VE1B units
1-4403-EN SKF VectoLub, VE1B units External minimal quantity lubrication, Volumetric metering The emql system SKF VectoLub is a clean and economical alternative for lubricant projection in minimal quantity.
More informationOil Module in the Inner V
Oil Module in the Inner V There are numerous oil supply passages under a cover in the V of the engine. The cover is bolted directly to the cylinder block, with a metal gasket positioned between them. Oil
More informationPneumatic atomizing nozzles ViscoMist flat fan, external mix Series 176
nozzles ViscoMist flat fan, external mix Versatile design with builtin pneumatic needle valve for liquid flow control and automatic clean-out. Three nozzle body configurations offer flexible tailoring
More informationSchlick PCA - Professional Coating Arm
Patented Anti-Bearding Technology (ABC) Schlick Anti-Bearding Technology (ABC-Technology) T e c h n o l o g y and Schlick PCA - Professional Coating Arm Areas of application: Coating Humidifying Treating
More informationSaw Blade Lube Systems
Environmentally Friendly Lubrication Saw Blade Lube Systems Cutting Edge Technology Saw Blade Lube Systems Cutting Edge Technology Cutting Edge Technology Unist saw blade lubrication systems deliver all
More informationA True Innovation in Oil Lubrication Technology
ORSCO Continuous Spray System: A True Innovation in Oil Lubrication Technology The ORSCO Philosophy: The best approach to lubrication is to deliver the least amount of lubricant required. Anything else
More information4/3-way high response directional control valve pilot operated with electrical feedback and integrated electronics (OBE)
4/3-way high response directional control valve pilot operated with electrical feedback and integrated electronics (OE) ype 4WRDE Nominal size to 35 Component series 5X Maximum operating pressure 3 bar
More informationDROPS INSTEAD OF LITRES!
MQL MINIMUM QUANTITY LUBRICATION. DROPS INSTEAD OF LITRES! 1 The Allube Micro-lubrication Systems are designed for use primarily in the varied metal cutting and forming processes to enable the replacement
More informationC O L M A N. Air Distribution LINEAR SLOT DIFFUSERS CD SERIES SERIES
C O L M A N Air Distribution E N G I N E E R E D A I R P R O D U C T S LINEAR SLOT DIFFUSERS CD SERIES CD SERIES LINEAR SLOT DIFFUSERS QUALITY AND EFFICIENCY WITHOUT COMPROMISE Application Colman Moducel
More informationMIG/MAG-Welding Torch Push-Pull Plus
T E C H N O L O G Y F O R T H E W E L D E R S W O R L D. MIG/MAG-Welding Torch Push-Pull Plus The "long-range torch" with the Plus The welding torches of the Push-Pull Plus series especially developed
More informationDual Applicators for Non-Atomized Conformal Coating Improve High- Volume Manufacturing
Dual Applicators for Non-Atomized Conformal Coating Improve High- Volume Manufacturing By Camille Sybert and Michael Szuch Nordson ASYMTEK Atomized spray is the most common method for applying conformal
More informationTRAINING BULLETIN TOOLS 7 December, 1978 HOSE NOZZLES (HAND HELD) 1. NOZZLE NOMENCLATURE AND IDENTIFICATION
TRAINING BULLETIN TOOLS 7 December, 1978 1. NOZZLE NOMENCLATURE AND IDENTIFICATION 1.1 A nozzle identification and nomenclature system is established to insure that issuance and recall of equipment as
More informationDirectional servo-valve in 4-way design
Directional servo-valve in 4-way design RE 2983/.11 Replaces: 7.3 1/ Type 4WS.2E... Size Component series X Maximum operating pressure 31 bar Maximum flow 1 l/min HD892 Type 4WSE2ED -X/...K31EV HD893 Type
More informationSPRAY CHARACTERISTICS Mist at low pressure; fog at high pressure Spray pattern: Cone-shaped Fog Flow rates: to l/min
MicroWhirl Fine tomization Outstanding atomization Rugged pinless design Drip-free performance 70 micron polypropylene filter Safety wire hole available Patented design Minimum operating pressure 7 Mist
More informationMPS 1-L Manual Powder System with the PG 1 Powder Gun
bar... 0. m /h 00 00 90 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 kv µa E Operating Instructions and Spare Parts List MPS -L Manual Powder System with the PG Powder Gun 0 0 + m /h Issued 0/9 MPS -L / PG An ITW
More information3/3 servo directional control valve with mechanical position feedback
Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic neumatic Electrical Mechanical () 426-4 www.cmafh.com 3/3 servo directional control valve with mechanical position feedback Type 4WS2EM...XN...-114
More informationExperimental investigation of micromist for effective machining
Experimental investigation of micromist for effective machining 1 Iram Lerma, Marko Jimenez & Dr. Immanuel Edinbarough Engineering Technology UT - Brownsville Brownsville, TX 2 Experimental investigation
More informationNozzle Features. For advice on nozzle choice please call +44 (0) or
This section provides information on the factors that influence spray characteristics: liquid flow, spray pattern, angle, droplet size and spray impact. It also offers advice on choosing the of nozzle
More informationSMT Place Manncorp 1610 Republic Road Huntingdon Valley, PA PIK-MANN ( )
SMT Place 2000 Benchtop Assembly Station with Integrated Dispense Manncorp 1610 Republic Road Huntingdon Valley, PA 19006 215-830-1200 800-PIK-MANN (800-745-6266) West Coast Office 858-490-6266 888-PIK-MANN
More informationFlow limiter SP/SMB3 Flow limiter SP/SMB6
-00-EN Flow limiter SP/SMB Flow limiter SP/SMB6 for circulating-oil lubrication systems Advantages reliable perpetual dispensation of individual volume flows - self-adjusting metering, thus identical volume
More information2-way proportional throttle valve for block installation
-way proportional throttle valve for block installation RE 90/07.05 Replaces: 03.00 / Types FE; FEE Size 6 Component series X Maximum operating pressure 35 bar Maximum flow 90 L/min bei p = 0 bar H4538
More informationFull cone nozzles.
nozzles Absorption Chemical process engineering Chlorine precipitation Cleaning Cooling esuperheating ust control Fire protection Foam control as treatment ing onto mats in air washers ing over packings
More informationNATURAL-BASED FLUID LUBRICANTS
NATURAL-BASED FLUID LUBRICANTS Cleaning Required Before Heat Treating LB-1000 LB-1100 LB-2000 FG-2000 Premium heavy-duty metalworking lubricant with chlorinated extreme-pressure additives for machining,
More informationFlow limiter SP/SMB 8... DSK US (09.04)
DSK 0-050-08-US (09.04) for mounting plates General information s are used in large oil circulation lubrication systems. The task of a flow limiter is to divide up the volumetric flow of the main line
More informationLUDV control block in mono block/sandwich plate design M7-20
LUDV control block in mono block/sandwich plate design M7-20 RE 64293 Edition: 06.2013 Replaces:. Size 20 Series 3X Maximum operating pressure On the pump side 380 bar On the actuator side 420 bar Maximum
More informationARTI Bileme GRINDING& WELDING MACHINERY
CNC HSS CIRCULAR SAW GRINDER provides full automatic process for the HSS circular saw blades of complete tooth removing, re-toothing, re-grinding and chamfering. is an ideal machine for the complete machining
More informationDirectional control - SRK series Solenoid valve
Directional control - series valve valve - 500, 700 Provide CD external dimension. SM SM SMU SMU Small size, big flow rate! high speed, react quickly ; ( Under 10 ms ) with indicator light and voltage
More informationPounds Per Square Inch (PSI)
Nozzle Size Selection Chart Determine the nozzle size by the pressure washer s GPM @ PSI (gallons per minute @ a specific pounds per square inch). If the nozzle size is too small, your equipment can be
More informationOverview of Products for Industry
1-0109-US Overview of Products for Industry Centralized lubrication and minimal quantity lubrication for machinery and systems Total-loss centralized lubrication systems Circulating oil lubrication systems
More informationPressure relief valve, direct operated. Type ZDBY D, Z2DBY D. Features. Contents. RE Edition: Replaces: 01.09
Pressure relief valve, direct operated ype ZDBY D, ZDBY D RE 5 Edition: -8 Replaces:.9 Size 6 Component series X Maximum operating pressure 35 bar Maximum flow 6 l/min tb3 Features Contents Sandwich plate
More informationFull cone nozzles. Axial-flow full cone nozzles
Absorption Chemical process engineering Chlorine precipitation Cleaning Cooling esuperheating ust control Fire protection Foam control Gas treatment ing onto mats in air washers ing over packings Surface
More informationSlot diffusers, Round duct diffusers. IMP Klima
, Round duct diffusers 04 Round duct diffusers 176 , Round duct diffusers SLOT DIFFUSERS, ROUND DUCT DIFFUSERS SWIRL DIFFUSERS, VARIABLE SWIRL DIFFUSERS CIRCULAR DIFFUSERS, SQUARE DIFFUSERS VENTILATING
More informationINDUTEC MS Modular System 8. INDUTEC MS coaxial spraying heads 12. INDUTEC MS valve units 18. INDUTEC MS pressure vessels 24
Contents INDUTEC MS Minimum Quantity Cooling Lubricating Systems INDUTEC MS Standard Systems 4 INDUTEC MS Modular System 8 Cooling and Lubricating gets to the Point. 6 One Solution for all Applications.
More informationRA / Pressure Reducing Valve, Pilot Operated Model DR (Series 5X) Ordering code 1/ PSI (350 bar) GPM (400 L/min)
R 26 892/06.98 Pressure Reducing Valve, Pilot Operated Model DR (Series 5) Size 10 to 0... 5000 PSI (50 bar)... 105 GPM (400 L/min) R 26 892/06.98 Replaces: 05.94 Pilot operated pressure reducing valve
More informationServ-O-Spray. Repeatable Precision
Serv-O-Spray Repeatable Precision Serv-O-Spray Repeatable Precision Serv-O-Spray delivers precise, repeatable shots of lubricant, and is ideal for any operation where controlled, intermittent fluid application
More informationBASIC INSTRUCTIONS SHIFTER KZ1 / KZ2 e X30 SHIFTER-TaG
BASIC INSTRUCTIONS SHIFTER KZ1 / KZ2 e X30 SHIFTER-TaG FEEDING: by fuel mixture 98NO (min. 95NO) and 4% oil (CIK homologated). ATTENTION: the engine is supplied without oil in the gearbox. GEARBOX OIL
More informationSection F Air Atomizing Spray Nozzles
Section F tomizing Overview If your application requires air atomizing nozzles, you ll find information on the largest selection in the industry available in this section. hoose from dozens of nozzle bodies,
More informationProportional pressure relief valve Types DBE(M) and DBE(M)E
RE 29 142/11.02 Replaces: 02.99 Proportional pressure relief valve Types DE(M) and DE(M)E Nominal size 32 1) Series 3X Maximum operating pressure 3 bar Maximum flow 600 L/min H/ 1764 1) NS 10; 25, Series
More informationModule. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01
Section 9 NOTE: This section applies to applicators with CC200 modules. 9-0 Table of Contents i Table of Contents Section 9 1. Introduction............................................... 9-1 2. Specifications.............................................
More informationProportional pressure reducing valve, pilot operated
Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (8) 426-548 www.cmafh.com Proportional pressure reducing valve, pilot operated Type DRE and ZDRE Size 6 Component
More informationF4-VB Spray Gun Plasma Spraying. Parts List PL EN 06
F-VB Spray Gun Plasma Spraying Parts List PL 0333 EN 06 Oerlikon Metco 1/2015 Oerlikon Metco Switzerland Rigackerstrasse 16 CH-5610 Wohlen +1 56 618 81 81 +1 56 618 81 00 www.oerlikon.com/metco Spare parts
More informationFlow limiter SP/SMB13 for line installation in circulating-oil lubrication systems.
1-3004-EN Flow limiter SP/SMB13 for line installation in circulating-oil lubrication systems. Flow limiters are used in circulating-oil lubrication systems. The task of a flow limiter is to divide up the
More informationCheck valve, pilot operated. Type SV and SL. Features. Contents. RE Edition: Replaces:
Check valve, pilot operated Type SV and SL RE 68 Edition: 07-0 Replaces: 07-0 Size 0, 0, and Component series Maximum operating pressure 5 bar Maximum flow 550 l/min H5558 Features For subplate mounting
More informationOperating Manual for FINE-SPRAY gun W 3/FZ-Duo
Operating Manual for FINE-SPRAY gun W 3/FZ-Duo Read this manual carefully before installing, operating or servicing this spray gun. Keep always handy for further use. 1 Introduction The FINE-SPRAY gun
More informationProportional pressure reducing valve, pilot operated
Proportional pressure reducing valve, pilot operated Type DRE and DREE Sizes 10 and 25 1) Component series 6X Maximum operating pressure Maximum flow Table of contents Content 315 bar 300 l/min Page Features
More informationand spring operated multiple-disk disc brakes FDLB, LB
Pressure Hydraulically released released and spring operated multiple-disk disc brakes FDLB, LB KWN 01 Couplings from Dresden / Germany By specialists for specialists general information external body
More informationAIR ATOMISER NOZZLES. Vapro Series. VP Body 24. VPX/VPL Body
AIR ATOMISER NOZZLES For applications where very fine droplets and low flow rates are required, the air atomiser range from Lurmark, including the VAPRO jet and ULTRA nozzles are the ideal choice. Air
More informationATOMIZATION OF LIQUID FUELS COMBUSTION AND FUELS
ATOMIZATION OF LIQUID FUELS THE PRINCIPLE OF LIQUIDS ATOMIZATION Atomization is the process whereby bulk liquid is transformed into a collection of drops. This transformation goes through the break-up
More informationFlow limiter SP/SMB US
Flow limiter SP/SMB 13... 1-3004-US for installation in the lines of circulating-oil lubrication systems General information Flow limiters are used in large circulating-oil lubrication systems. The task
More informationSV1217-SS SPRAY VALVE O P E R AT I N G M A N U A L
SV1217-SS SPRAY VALVE O P E R AT I N G M A N U A L I&J FISNAR INC. 2003 GENERAL DESCRIPTION The SV1217-SS spray valve is operated by air pressure, providing precise deposit control for low to medium viscosity
More informationStandard Specifications Model. How to Order. Mist spray unit. Recommended Equipment. Mixing valve
Mist Spray Unit Series MU/ Intermittent spray to cutting and press gear chains, etc. Standard Specifications MU MU Inlet air Oil tank set range. MPa. to. MPa Oil tank capacity (cm ) Total capacity: Effective
More informationProportional pressure reducing valve, 3-way variant, pilot operated
roportional pressure reducing valve, 3-way variant, pilot operated RE 29286/1.1 Replaces: 2.8 1/14 ypes 3DRE(M) and 3DRE(M)E Sizes 1 and 16 Component series 7X Maximum pressure setting 315 bar (size 1)
More informationTHE IDLE CIRCUIT AND THE PROGRESSION. We have seen how in a "basic"
THE IDLE CIRCUIT AND THE PROGRESSION Manufacture and operation of two very important systems, which allow the practical use of a carburetor for motorcycles We have seen how in a "basic" (simplified) carburetor,
More information2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
More informationCheck valve. Type Z1S. Contents. Features. RE Edition: Replaces: 09.10
Check valve Type ZS RE 537 Edition: 05-06 Replaces: 09.0 Size 0 Component series 4X Maximum operating pressure 350 bar [5076 psi] Maximum flow 00 l/min [6.4 US gpm] H7647 Features Sandwich plate valve
More informationRexroth Hydraulics. Servo directional valve of 4-way design Type 4WS.2EM RE /03.99
RE 29 564/03.99 Replaces: 29 563 Servo directional valve of 4-way design ype 4WS.2EM Nominal size 6 Series 2X Maximum operating pressures 210 / 315 bar Maximum flow 40 L/min H//D 5994/98 ype 4WS2EM 6-2X/.E...K17EV
More informationMIG/MAG Welding Torch Push-Pull Plus
T e C h n O l O g y F O r T h e W e l d e r S W O r l d. MIG/MAG Welding Torch Push-Pull Plus The "long-range torch" with the Plus The welding torches of the Push-Pull Plus series especially developed
More informationPounds Per Square Inch (PSI)
Nozzle Size Selection Chart Determine the nozzle size by the pressure washer s GPM @ PSI (gallons per minute @ a specific pounds per square inch). If the nozzle size is too small, your equipment can be
More information3/2 and 4/2 directional poppet valve with solenoid actuation
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic neumatic Electrical Mechanical (800) 426-5480 www.cmafh.com 3/2 and 4/2 directional poppet valve with solenoid actuation ype M-.SED Size 10 Component
More informationElectric Mini Slides MSC-EL
Electric Mini Slides MSC-EL R10EN 2604 (11.08) The Drive & Control Company Electric Mini Slides, MSC-EL R10EN 2604 (11.08) Mini Slides, MSC-EL Product Description 4 Selection Guide 6 Maximum thrust 6
More informationModule. Table of Contents. Section 9. Module NOTE: This section applies to applicators with MB200 modules.
9- Section 9 NOTE: This section applies to applicators with MB200 modules. Table of Contents.................................................... 9- Introduction................................................
More information1. Replace the plugs with the cheap Autolite (25) copper-core plugs, set to 80 thou gap.
A recently encountered e-mail from Robert Calloway states that Tesla s bi-filar series-connected coil is effective in picking up radiant energy. In the light of that, and in the absence of further information
More informationNUMBER: S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007
NUMBER: 1 60 07 S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007 SUBJECT: N3 ELECTRONIC INJECTOR PUBLICATION: 6SE483 The Series 60 Service Manual has been revised. Engine models built from December
More informationOperating Manual for extrusion valve MMKD-40 KV/LV/LVP
Operating Manual for extrusion valve MMKD-40 KV/LV/LVP Read this manual carefully before installing, operating or servicing this equipment. Keep always handy for further use. ALFRED SCHÜTZE Apparatebau
More informationDirectional servo-valve of 4-way design
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) 426-54 www.cmafh.com Directional servo-valve of 4-way design Type 4WSE3E 32 Size 32 Component series 5X Maximum
More information2-way flow control valve
-way flow control valve RE 864/05. Replaces: 0.03 /8 ype ZFRM Size 6 Component series X Maximum operating pressure 35 bar Maximum flow 3 l/min H5379 able of contents Contents Page Features Ordering code
More informationMIXTURE FORMATION IN SPARK IGNITION ENGINES. Chapter 5
MIXTURE FORMATION IN SPARK IGNITION ENGINES Chapter 5 Mixture formation in SI engine Engine induction and fuel system must prepare a fuel-air mixture that satisfiesthe requirements of the engine over its
More informationManual and universal sprayers
Manual and universal sprayers 401 402 Professionally equipped mini sprayers with an available capacity of 1 l/2 l, Viton seals and lever lock. The robust pump reaches the required operating pressure after
More information迅捷 PDF 编辑器. Supply pressure compensator, direct operated RE 29231/ Type ZDC
Supply pressure compensator, direct operated ype ZDC Size 6 Component series X Maximum operating pressure 50 bar Maximum flow 35 l/min able of contents Contents Page Features Ordering code Function, section
More informationProportional pressure relief valve Types DBE(M) and DBE(M)E
RE 29 142/02.99 Replaces: 06.97 Proportional pressure relief valve Types DE(M) and DE(M)E Nominal size 32 1) Series 3X Maximum operating pressure 3 bar Maximum flow 600 L/min H/ 1764 1) NS 10; 25, Series
More informationTwin throttle check valve
win throttle check valve RE 7506/05. Replaces: 0.03 /8 ype ZFS Size 6 Component series 4X Maximum operating pressure 35 bar Maximum flow 80 l/min H5556 able of contents Contents Page Features Ordering
More informationAtomizing Spray Nozzles All stainless steel construction for durability and corrosion resistance!
Atomizing All stainless steel construction for durability and corrosion resistance! What Are Atomizing Nozzles? EXAIR s Atomizing atomize fluids (most commonly water) in a range of spray patterns for a
More information4-way directional servo-valve
4-way directional servo-valve RE 29564/09.10 Replaces: 01.07 1/12 Type 4WS.2E Size 6 Component series 2X Maximum operating pressure 315 bar Maximum flow 48 l/min HD5994 Table of contents Contents age Features
More informationMulticore diffusers. introduction. type control. options. finish. sizes SQUARE AND RECTANGULAR DIFFUSERS
SQUARE AND RECTANGULAR DIFFUSERS introduction The IC diffuser is a versatile form of air terminal offering the facility of multi directional throw patterns in a wide range of frame sizes. Each core style
More informationChapter 5: Flow Valves
Catalogue HY11-300/UK Contents Chapter : Flow Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/4 3/8 1/2 3/4 1 06 10 16 Throttle valves, manual adjustment MVI -2 NS -4 FS With free
More informationYARWAY NARVIK MODEL 88 SPID SMALL PIPE INLINE DESUPERHEATER
A wide range of desuperheaters, pneumatic actuators, strainers to satisfy all specifications of the power, pulp and paper industry and process gas applications FEATURES Fabricated construction Special
More informationOwner's Manual. Model: ATVBK-3025 ( ) (Boomless Nozzle Kit for ATV Mounting) Technical Specifications. Assembly. General Information
Owner's Manual Model: ATVBK-305 (530484) (Boomless zzle Kit for ATV Mounting) Technical Specifications 30 Foot Spray Coverage w/boom Corrosion-Resistant zzles Caution: Always check the vehicle load rating
More informationmechanics Features Technical specification Ordering information Dimensioned drawings Aluminium profiles made by isel
Panel profiles PP profiles For fast and easy erection of frames, benches and racks luminium, naturally anodised easy, very strong under load Top edge particularly suitable as a load-bearing cladding, also
More informationNOZZLE TYPES AND CHARACTERISTICS
95 NOZZLE TYPES AND CHARACTERISTICS Dennis w. Bintner Design Engineer Delavan Hanufacturing Company West Des Moines, Iowa The many varieties of herbicides on the market today, make the proper selection
More informationGO LEAN, THINK GREEN
MANUFACTURERS ALLIANCE GROUP, INC. MINIMUM QUANTITY LUBRICATION & ORGANIC LUBRICANTS *SERVING THE INDUSTRY FOR OVER 20 YEARS* GO LEAN, THINK GREEN 1-800-441-2023 www.maglube.com info@maglube.com Why Micro-Lubrication
More informationHot Air Devices for welding, heating, shaping of thermoplastic materials. Floor welding machine Nozzles Accessories
S C H W E I S S T E C H N I K O n e c o m p a n y 3 p r o d u c t i o n l i n e s Hot Air Devices for welding, heating, shaping of thermoplastic materials Floor welding machine Nozzles Accessories Hot
More informationHSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam
HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin
More informationCutting
wist drills Miniature drills Sheet metal drills Core drills Step drills Centring and spot drills aper pin drills Solid carbide drills Solid carbide tapping ools Carbide reversible cutting inserts wist
More informationSteam-condensation from singlesteam-hole
Steam-condensation from singlesteam-hole as well as from annulargap steam injector Lars Hamberg Tetra Pak Processing System Questions of interest for Tetra Pak concerning Steam Injection What types of
More information4-way directional servo valve Type 4WS.2E
RE 29 91/06.02 Replaces: 03.93 4-way directional servo valve Type 4WS.2E Nominal size 16 Series 2X Maximum operating pressure 2/31 bar Maximum flow 3 L/min Overview of contents Contents Page Features 1
More informationDistributed by: Lubrication Technologies, Inc. 120 Bosworth St., West Springfield MA LUBE (5823)
1 2 INDEX PAGE INTRODUCTION 4 APPLICATIONS 5 MAIN ADVANTAGES 6 WORKING PRINCIPLE 7 9 UNITS UCFG, UCGF SE, AGGF, AGGF SE, UCSG, UCSG SE, AGSG E AGSG SE UNITS MC EL 3P 4P 5P 6P 7P, MC EL 3M 4M 5M 6M 7M,
More informationApplication Guidelines
Grilles and Registers Application Guidelines Introduction Overview It is the intent of this section to give some basic application guidelines for the use of supply and return grilles and registers in a
More informationProportional directional valves, pilot operated, with electrical position feedback and integrated electronics (OBE)
Proportional directional valves, pilot operated, with electrical position feedback and integrated electronics (OE) RE 29075/08.13 Replaces: 08.04 1/22 Type 4WRKE Size 10 to 35 Component series 3X Maximum
More informationRE / Check-Q-meter type FD, series 2X. Ordering details FD 2X / V * Symbols 1/8. Replaces: 03.92
RE 1/09.9 1/03.9 Check-Q-meter type FD, series Sizes 1, 1,, 3 Up to 0 L/min Up to 30 bar RE 1/09.9 Replaces: 03.9 Features: For installation in manifolds (cartridge valve), With SE flanged ports, For sub-plate
More information