4-Cycle Engine ENGINE PARTS. OPERATOR S MANUAL. Maintain Your. With Genuine. TecumsehPower

Size: px
Start display at page:

Download "4-Cycle Engine ENGINE PARTS. OPERATOR S MANUAL. Maintain Your. With Genuine. TecumsehPower"

Transcription

1 4-Cycle Engine OPERATOR S MANUAL Horizontal Crankshaft Air-Cooled LH9SA/LH9SP (HSSK40-) LH8SA/LH8SA (HMSK80-0) OH9SA/OH9SP (OHSK0-7) OH8SA/OH8SA (OHSK80-0) For your convenience, enter your engine model, spec and DOM numbers here. ENGINE MODEL: SPEC: DOM: Visit our website at Maintain Your Register your TecumsehPower Engine Maintenance Tips On-Line Parts Locate your nearest TecumsehPower Servicing Dealer ENGINE With Genuine TecumsehPower PARTS (English) 6/0/08 Small Engine Parts

2 Table of Contents Safety Definitions...ii I. General Safety Precautions... II. How to Get Service... III. Oil and Fuel Specifications... 4 IV. Before Starting Your Engine... 4 V. Starting Your Engine... 9 VI. Stopping Your Engine and Short-Term Storage... VII. Maintenance... 7 VIII. Transporting Your Engine... IX. Storing Your Engine... 4 X. Preventing Forest, Brush and Grass Fires... 6 XI. Maintenance Intervals... 6 California & US EPA Emission Control Warranty Statement... 8 Emission Control System Warranty... 9 XII. Warranty Information... 0 IMPORTANT NOTICE! Safety Definitions Statements in this manual preceded by the following words and graphics are of special significance:! indicates a potentially hazardous situation which if NOT avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if NOT avoided, may result in minor or moderate injury. Or CAUTION CAUTION Indicates a potential situation which, if NOT avoided, could result in equipment or property damage. NOTE Refers to important information and is placed in italic type. It is recommended that you take special notice of all items discussed on the next two pages and wear the appropriate safety equipment. Before operating this engine it is your responsibility to read this Operator s Manual. Follow these basic rules for your personal safety: Keep this manual handy at all times for future reference. Read it carefully and familiarize yourself with operating, maintenance, components and safety instructions. Notice Regarding Emissions NOTE Engines which are certified to comply with California and U.S. EPA emission regulations for SORE (Small Off Road Equipment), are certified to operate on regular unleaded gasoline, and may include the following emission control systems: (EM) Engine Modification and (TWC) Three-way Catalyst (if so equipped). TecumsehPower Contact Information For engine adjustments, repairs or warranty service NOT covered in this manual, contact your nearest Authorized TecumsehPower Servicing Dealer. Find them on our website at or call TecumsehPower Company at for additional information. The trademarks TECUMSEH and the DESIGN (Native American Head logo) are registered trademarks of Tecumseh Products Company and are used by TecumsehPower Company under license from Tecumseh Products Company. TecumsehPower Company is no longer owned by Tecumseh Products Company nor is it associated or affiliated in any way with Tecumseh Products Company. Copyright 006, 008 TecumsehPower Company All Rights Reserved Page ii 4-Cycle Snow King Engine 8-7-4

3 I. General Safety Precautions! Read equipment manufacturer s manual and this material thoroughly before using this engine. Failure to do so can result in serious injury or death. Consult your local Authorized TecumsehPower Servicing Dealer, call , or go to for additional information. A. Avoid Carbon Monoxide Poisoning All engine exhaust contains carbon monoxide, a deadly gas. Breathing carbon monoxide can cause headaches, dizziness, drowsiness, nausea, confusion and eventually death. Carbon monoxide is a colorless, odorless, tasteless gas which may be present even if you DO NOT see or smell any engine exhaust. Deadly levels of carbon monoxide can collect rapidly and you can quickly be overcome and unable to save yourself. Also, deadly levels of carbon monoxide can linger for hours or days in enclosed or poorly-ventilated areas. If you experience any symptoms of carbon monoxide poisoning, leave the area immediately, get fresh air, and SEEK MEDICAL TREATMENT. To prevent serious injury or death from carbon monoxide: NEVER run engine indoors. Even if you try to ventilate engine exhaust with fans or open windows and doors, carbon monoxide can rapidly reach dangerous levels. NEVER run engine in poorly-ventilated or partially enclosed areas such as barns, garages, basements, carports, under dwellings, or in pits. NEVER run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. B. Avoid Gasoline Fires Gasoline (fuel) vapors are highly flammable and can explode. Fuel vapors can spread and be ignited by a spark or flame many feet away from engine. To prevent injury or death from fuel fires, follow these instructions: NEVER store engine with fuel in fuel tank inside a building with potential sources of ignition such as hot water and space heaters, clothes dryers, electric motors, etc. NEVER remove fuel fill cap or add fuel when engine is running. NEVER start or operate the engine with the fuel fill cap removed. Allow engine to cool before refueling. NEVER fill fuel tank indoors. Fill fuel tank outdoors in a well-ventilated area. DO NOT smoke while refueling tank. Use only an approved red GASOLINE container to store and dispense fuel. TecumsehPower Company recommends purchasing gasoline in containers with a capacity of. gallons or less. Small containers are easier to handle and help eliminate spillage during refueling. DO NOT pour fuel from engine or siphon fuel by mouth. To empty the fuel tank, see "I. Draining Fuel" instructions on page 4. C. Adult Supervision of Operation, Refueling and Maintenance The manufacturer of the equipment may provide information about who is allowed to use this engine (see equipment manufacturer s manual). NOT everyone who is allowed to use this engine is capable of safely and responsibly operating, maintaining and/or fueling it. TecumsehPower Company recommends the following: An adult should fuel this engine. NEVER allow children to refuel this engine. See "E. Filling Fuel Tank" instructions on page 8. An adult should perform maintenance on this engine. See "VII. Maintenance" instructions on page 7. Only allow children to perform maintenance if an adult has determined they are experienced and capable of such operation. An adult should start the engine. See "G. Avoid Accidental Starts" instructions on page. Only allow children to start the engine if an adult has determined they are experienced and capable of such operation. To avoid unsupervised operation of the engine, especially by children, NEVER leave it unattended when it is running. Remove ignition key, if equipped. D. Stay Away from Rotating Parts NEVER operate the engine with an unguarded engine shaft or flywheel. See Figure on page. The equipment manufacturer may attach a sprocket and chain or pulley and belt to the engine shaft. If these parts are NOT properly guarded, or if you are NOT sure whether they are properly guarded, DO NOT use your engine; contact the equipment manufacturer. Hands, feet, hair, jewelry, clothing, etc.,can become entangled in rotating parts, leading to serious injury or death. To avoid serious injury or death, be sure the flywheel guard is in place. See Figure on page Cycle Snow King Engine Page

4 E. DO NOT Modify Engine To avoid serious injury or death, DO NOT modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. NEVER tamper with factory setting of engine governor.! Use of this engine on fun-carts, go-karts, or mini-bikes can result in serious injury or death. TecumsehPower Company manufactures the Power Sport line of engines for use in such applications. Consult your local Authorized TecumsehPower Servicing Dealer, call , or visit for additional information. F. Avoid Burns and Fire from Hot Surfaces The muffler and other engine parts become extremely hot during operation and remain hot after the engine has stopped. To avoid severe burns on contact, STAY AWAY from hot areas of engine. DO NOT operate the engine without the muffler guard in place, if equipped. TecumsehPower Company offers a muffler guard for all 4-Cycle Snow King Engines. Consult your local Authorized TecumsehPower Servicing Dealer or call for additional information. See Figure. To reduce the risk of fire keep all materials that can burn, including grass and leaves, away from muffler and rest of engine. DO NOT operate, idle or park engine powered equipment in long dry grass or other dry ground cover. G. Avoid Accidental Starts To prevent accidental starting when working on equipment always: Carefully disconnect spark plug wire and keep it away from spark plug. See Figures and 4. Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. Carefully attach the spark plug wire to the grounding post, if provided. Disconnect battery at negative terminal first, if engine is equipped with a DC electric starter. Turn all engine switches to OFF position. Remove ignition key, if provided. H. Use Hearing Protection Engine noise may cause hearing damage. Always wear hearing protection when operating an engine. Figure. Typical Flywheel Guard Location OH8SA/OH8SA OH9SA/OH9SP LH9SA/LH9SP LH8SA/LH8SA Figure. Muffler Guards Available Figure. Disconnecting/Connecting Spark Plug Figure 4. Typical Spark Plug Connection Page 4-Cycle Snow King Engine 8-7-4

5 II. How to Get Service For engine adjustments, repairs or warranty service NOT covered in this manual, contact your nearest Authorized TecumsehPower Servicing Dealer. Find them on our website at or call TecumsehPower Company at for additional information. Visit our web site at A. Engine Identification Decal LOG ON! Register Your TecumsehPower Engine Maintenance Tips On-Line Store Locate your nearest TecumsehPower Servicing Dealer A sample engine identification decal is located in the next column and indicates the engine s model number, specification and date of manufacture (DOM). See Figure. ENGINE MODEL: SPEC: DOM: TECUMSEHPOWER COMPANY THIS ENGINE MEETS CALIF & US EPA 08 PHI APPLICABLE EMISSION REGULATIONS FOR SI SORE ENGINES EM LV9EA 640D 040AA000 4TPXS.9BB 9 Please look at the decal on your engine. Fill in the engine information in the spaces provided for future reference. The engine identification decal also includes engine life specifications for the emissions-related useful life period of your engine. This period relates to the emission compliance life as certified by EPA and/or CARB. LH9SA/LH9SP and OH9SA/OH9SP models are designated as C hours. LH8SA/LH8SA and OH8SA/OH8SA models are designated as C 0 hours. B. Technician s Handbooks If you have a general understanding of internal combustion engines and wish to repair and service your engine and/or engine emission control systems yourself, a Technician s Handbook is available from your Authorized TecumsehPower Servicing Dealer. See Figure 6. This handbook covers repairs and adjustments not covered within this Operator s Manual, and it is intended for individuals who have had adequate training, experience and who practice proper tool usage. Service procedures should be clearly understood and practiced when servicing TecumsehPower engines. Order as part #6944A or #74004 for OH9SA/ OH9SP and OH8SA/OH8SA models. Order as part #6909 or # for LH9SA/ LH9SP and LH8SA/LH8SA models. TecumsehPower Company manufactures and is responsible only for the engine used on this power equipment. If repair or service is needed for anything other than the engine, contact the service source recommended by the equipment manufacturer. Figure. Engine Identification Decal Figure 6. Technician s Handbooks Cycle Snow King Engine Page

6 III. Oil and Fuel Specifications A. Oil To operate your engine you need to use a clean, high quality, detergent oil. For recommended engine oil, see Table. In addition, you need to be sure the oil sump contains the correct amount of oil to operate properly. For recommended oil sump capacity, see Table. Be sure original container is marked A.P.I. Service SL/SJ. Using multigrade oil above F (0 C) will increase oil consumption. SAE 0W40 is NOT recommended. Special-formulated oils are available at your Authorized TecumsehPower Servicing Dealer. B. Fuel Use unleaded regular, unleaded premium or reformulated automotive fuel only. You may use gasoline containing the components identified in Table. DO NOT use leaded fuel. Fuel must be fresh and clean. NEVER use fuel left over from last season or stored for long periods. NEVER mix oil with fuel. DO NOT use fuel containing Methanol (Wood Alcohol). The use of alternative fuels such as E8 CAUTION or E0 are NOT recommended for use in TecumsehPower engines. Alternative fuels with high alcohol content can cause hard starting, poor engine performance, and may cause internal engine damage. NOTE Damage and/or performance problems that occur from use of fuels other than those listed in the Operator s Manuals will not be considered warranty. IV. Before Starting Your Engine A. Checking Oil Level To avoid engine damage, it is important to: Check oil level before each use and every operating hours when engine is warm. Check oil level more frequently during engine break-in. Keep oil level between FULL and ADD marks on oil fill cap/dipstick or to point of overflow on engines with an oil fill cap/plug. See Figure 7. Be sure oil fill cap/dipstick or oil fill cap/plug is tightened securely. DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. DO NOT allow oil level to fall below the ADD mark on oil fill cap/dipstick. Doing so may result in equipment malfunction or damage. Contact your Authorized TecumsehPower Servicing Dealer for TecumsehPower Oil. Some engines are equipped with an oil fill cap/dipstick or oil fill cap/plug (see equipment manufacturer s instructions). To change the oil on your engine, see "B. Changing Oil" instructions on page O C -0 O F -0 O C 0F O Table. Recommended Oil TecumsehPower Recommended Oil Usage Multi Grade TecumsehPower Part No. 706A or SAE W0 or SAE 0W TecumsehPower Synthetic Part No. 706 or SAE 0W0-0 O C 0 O F O F 0C O Table. Oil Sump Capacity Oil Sump Capacity Engine Ounces U.S. Pints Liters Model Number -/4.6 LH9SA/LH9SP OH9SA/OH9SP 6 -/8.77 LH8SA/LH8SA OH8SA 8 -/4.8 OH8SA Table. Recommended Fuel Fuel Component Percentage Ethanol 0% Grain Alcohol ( Gasohol ) 0% MTBE (Methyl Tertiary Butyl Ether) % ETBE (Ethyl Tertiary Butyl Ether) % FULL OK ADD 40 O F 0 O C 60 O F 0 O C Figure 7. Engine Oil Level Straight Grade TecumsehPower Part No. 70A or SAE 0W 80 O F 0 O C 00 O F Fill Between FULL and ADD Marks 40 O C Page 4 4-Cycle Snow King Engine 8-7-4

7 B. Filling Oil Sump I. Oil Fill Cap/Dipstick If your engine has an oil fill cap/dipstick go to step. If your engine does NOT have an oil fill cap/dipstick, see "II. Oil Fill Cap/Plug" instructions below.. Be sure engine is upright and level.. Unscrew oil fill cap/dipstick from oil filler tube and wipe dipstick clean. See Figures 8 and 9.. Screw oil fill cap/dipstick back into oil filler tube. Tighten securely. 4. Unscrew and remove oil fill cap/dipstick from oil filler tube. Note oil level. If oil reading on dipstick is below ADD mark, slowly add oil to reach FULL level. See Figure 7 on page 4. Afterward, continue reading instructions below.. Screw oil fill cap/dipstick back into oil filler tube. Tighten securely. 6. Wipe away any spilled oil. OH8SA/OH8SA OH9SA/OH9SP NOTE To change oil for engines with an oil fill cap/dipstick, see "B. Changing Oil" instructions on page 7. II. Oil Fill Cap/Plug If your engine does NOT have an oil fill cap/dipstick, go to step. If your engine has an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions above.. Be sure engine is upright and level.. Clean area around oil fill cap/plug. See Figure 9.. Unscrew oil fill cap/plug. 4. Add oil to overflow point, making sure to avoid spilling.. Screw oil fill cap/plug back into oil fill hole. Tighten securely. 6. Wipe away any spilled oil. NOTE To change oil for engines with an oil fill cap/plug, see "B. Changing Oil" instructions on page 7. LH9SA/LH9SP LH8SA/LH8SA Figure 8. Oil Fill Cap/Dipstick Locations Angled Front View Back View. Oil Fill Cap/Dipstick. Oil Fill Cap/Plug. Oil Drain Plug Figure 9. Oil Fill/Drain Locations Cycle Snow King Engine Page

8 C. Check the Following Items NOTE Be sure equipment is in neutral before attempting to start (see equipment manufacturer s instructions).. Be sure ignition switch on engine or equipment is in ON, RUN or START position. See Figures 0, and. Or Insert ignition key, if present (see equipment manufacturer s instructions) into ignition key slot in carburetor cover. DO NOT turn ignition key. Be sure ignition key snaps into place. See Figures 0 and.. Be sure fuel valve, if present (see equipment manufacturer s instructions) is open. See Figure.. Check engine and equipment before each operation for loose nuts, bolts and attachments; keep these items tightened. D. Check the Item Descriptions The item descriptions listed below are for all 4-Cycle Horizontal Crankshaft Snow King Engine Models. See Figure 4 on page 7. Figure 0. Ignition Key. Control Lever. Oil Drain Plug. Choke 4. Ignition Key or Ignition Switch. Carburetor Cover 6. Muffler (with Muffler Guard, if equipped) 7. Oil Fill Cap/Dipstick 8. Spark Plug Cap 9. Fuel Fill Cap 0. Starter Cord Handle. Fuel Valve. Primer Bulb. Recoil Starter/Flywheel Guard Figure. Possible Ignition Key Locations SLOW RUN FAST CHOKE PRIMER Figure. Typical Engine Symbols Fuel Tank Fuel Valve OPEN Position Shown Turn Valve Clockwise To OFF Position Figure. Fuel Valve Positions Page 6 4-Cycle Snow King Engine 8-7-4

9 OH8SA/OH8SA OH9SA/OH9SP LH9SA/LH9SP LH8SA/LH8SA Figure 4. 4-Cycle Snow Engine Components Cycle Snow King Engine Page 7

10 E. Filling Fuel Tank An adult should fuel this engine. NEVER allow children to refuel this engine. Gasoline (fuel) vapors are highly flammable and can explode. Fuel vapors can spread and be ignited by a spark or flame many feet away from engine. To prevent injury or death from fuel fires, follow these instructions:. Stop engine and allow it to cool before refueling.. Be sure engine is outdoors and in a well-ventilated area.. Clean area around fuel fill cap and remove fuel fill cap. See Figure 4 on page 7. Afterward, continue reading instructions below. NOTE For recommended fuel, see Table and "III. Oil and Fuel Specifications" instructions on page 4. Afterward, continue reading instructions below. 4. Using an approved red GASOLINE container, add fuel slowly, being careful to avoid spilling. DO NOT overfill fuel tank. Leave space in the tank to allow fuel to expand without overflowing.. Replace fuel fill cap securely and wipe up spilled fuel before starting engine. If fuel is spilled DO NOT start engine. Move machine away from area of spillage. Avoid creating any source of ignition until fuel vapors are gone. NOTE Replace a damaged or missing fuel fill cap only with a genuine TecumsehPower replacement Fuel Fill Cap. Failure to do so may VOID YOUR WARRANTY. See Figure. 6. Be sure fuel valve, if present (see equipment manufacturer s instructions) is open. See Figure 6. F. Electrical Power Figure. Possible Fuel Fill Cap(s) Figure 6. Fuel Valve Positions Front View Fuel Valve OPEN Position Shown Bottom View 6 Fuel Tank Turn Valve Clockwise To OFF Position 0V AC When connecting power cord, always connect power cord to switch box on engine first; then into outlet. See Figure 7. For European 0V AC applications use an appropriate grounded extension lead available locally. Determine what type of power source outlet you will be connecting the power cord to, before you start your engine. See "A. Engines with Electric Starters" instructions on page Power Cord to Outlet. Switch Box. Starter Button 4. Schuko Plug. Power Cord to Switch Box on Engine 6. Electric Starter Switch Box on Engine 0V AC Figure 7. Electric Starter Connections Page 8 4-Cycle Snow King Engine 8-7-4

11 V. Starting Your Engine To avoid serious injury or death, an adult should start this engine. Only allow children to start engine if an adult has determined they are experienced and capable of such operation. If you are unable to start this engine after following instructions in this manual, contact your Authorized TecumsehPower Servicing Dealer. To avoid serious burn injuries or damage to your engine, DO NOT attempt to start or troubleshoot this engine in any other way. For example: DO NOT use starting fluid. DO NOT spray flammable vapors into carburetor. DO NOT put flammable liquids into carburetor. DO NOT operate engine or pull on starter rope with spark plug removed. Fuel can spray from spark plug hole and ignite. SLOW RUN FAST CHOKE PRIMER Figure 8. Typical Engine Symbols NOTE If engine is remotely controlled (see equipment manufacturer s instructions) your equipment may have one or more of the following engine symbols. See Figure 8. This section contains starting instructions for several different types of engines. In order to locate the instructions that apply to your engine, first determine what type of starter you have. If you have an electric starter, see A. Engines with Electric Starters instructions on page 0. If you have a manual recoil starter, see B. Engines with Recoil Starters instructions on page Cycle Snow King Engine Page 9

12 A. Engines with Electric Starters If you have a recoil starter, see B. Engines with Recoil Starters instructions on page. Some electric starters are equipped with a 0V AC Three-Wire Power Cord and Plug designed to operate on a 0V AC household current. It must be properly grounded at all times to avoid the possibility of injury or death from electrical shock. a. Determine if your house wiring has a Ground Fault Interrupted (GFI) Three-Wire Grounded System; if you are not sure ask a Licensed Electrician. b. If your house wiring does not have a GFI Three-Wire Grounded System, DO NOT USE THIS ELECTRIC STARTER UNDER ANY CONDITION. c. If your house wiring is grounded and a GFI Three-Prong Wall Receptacle is not available at the location where your starter will be used, one must be installed by a Licensed Electrician BEFORE USING THE ELECTRIC STARTER.. To avoid carbon monoxide poisoning, be sure engine is outdoors in a well-ventilated area.. Be sure fuel valve, if present (see equipment manufacturer s instructions) is open and all switches are on. See Figure 9. If your engine is equipped with a V battery-operated electric starter, proceed to step 4. When connecting power cord, always connect power cord to switch box on engine first; then into outlet. See Figure 0. For European 0V AC applications use an appropriate grounded extension lead available locally.. Connect power cord to switch box on engine. See Figure Plug end of power cord into outlet. 4 Fuel Valve OPEN Position Shown Fuel Tank Figure 9. Fuel Valve Positions Turn Valve Clockwise To OFF Position. Power Cord to Outlet. Switch Box. Starter Button 4. Schuko Plug. Power Cord to Switch Box on Engine 6. Electric Starter Switch Box on Engine 6 0V AC 0V AC Figure 0. Electric Starter Connections Page 0 4-Cycle Snow King Engine 8-7-4

13 . Move engine speed control to FAST position. See Figures and. 6. Set choke control to FULL CHOKE position (see equipment manufacturer s instructions). See Figure 4 on page. Afterward, continue reading instructions below. 7. Hold the primer bulb in for one full second each time you press it. See Figure. Make sure you cover vent hole with your thumb. Repeat twice for a total of three primes. DO NOT operate an electric starter for more than seconds each attempt. DO NOT use primer bulb to restart a warm engine after a short shutdown. Doing so will flood the engine and may result in equipment malfunction. If restarting a warm engine after a short shutdown, move engine speed control to FAST position and move choke control to NO CHOKE position. See Figures, and 4. Afterward, continue reading instructions below. 8. Push starter button or turn ignition switch key (see equipment manufacturer s instructions) to start engine. See "C. Check the Following Items" instructions on page 6. Afterward, continue reading instructions below. NOTE If engine fails to start after attempts repeat steps thru When engine starts: a. Release starter button or ignition switch key. See Figure 0 on page 0. Afterward, continue reading instructions below. b. Momentarily move choke control to / CHOKE position until engine runs smoothly. See Figure 4 on page. Afterward, continue reading instructions below. c. Next, move choke control to NO CHOKE position. 0. Move engine speed control to desired speed in RUN range. See Figures and. If engine starts but falters when choke control is moved to NO CHOKE position: a. Momentarily move choke control back to FULL CHOKE position. b. Next, move choke control to / CHOKE position until engine runs smoothly. c. Finally, move choke control to NO CHOKE position. If engine dies after choke control is moved to NO CHOKE position repeat steps thru 0 to restart engine.. If engine fires but does not continue to run, move choke control to NO CHOKE position and start engine. See Figure 4 on page. Afterward, continue reading instructions. SLOW RUN FAST CHOKE PRIMER Figure. Typical Engine Symbols. Engine Speed Control. Position. SLOW Position 4. RUN Range. FAST Position Figure. Engine Speed Control Positions. Primer Bulb. Vent Hole Figure. Pressing Primer Bulb. If engine fails to start after attempts in the NO CHOKE position, move choke control to FULL CHOKE position and start engine. NOTE When disconnecting power cord, always disconnect power cord from outlet first; then disconnect power cord from switch box on engine. See Figure 0 on page 0. Afterward, continue reading instructions below.. Disconnect power cord from outlet. See Figure 0 on page 0. Afterward, continue reading instructions below. 4. Disconnect power cord from switch box on engine. See Figure 0 on page 0. Afterward, continue reading instructions below.. If engine does not start after following steps thru, contact your Authorized TecumsehPower Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way Cycle Snow King Engine Page

14 LH9SA/LH9SP OH8SA/OH8SA OH9SA/OH9SP LH8SA/LH8SA. NO CHOKE Position. / CHOKE Position. FULL CHOKE Position Figure 4. Choke Control Positions Page 4-Cycle Snow King Engine 8-7-4

15 B. Engines with Recoil Starters If you have an electric starter, see A. Engines with Electric Starters instructions on page 0. DO NOT pull starter rope with engine CAUTION running. Doing so may VOID YOUR WARRANTY.. To avoid carbon monoxide poisoning, be sure engine is outdoors in a well-ventilated area.. Be sure fuel valve, if present (see equipment manufacturer s instructions) is open and all switches are on. See Figure.. Move engine speed control to FAST position. See Figures 6 and Set choke control to FULL CHOKE position (see equipment manufacturer s instructions). See Figure 4 on page. Afterward, continue reading instructions below.. Hold the primer bulb in for one full second each time you press it. See Figure 8. Make sure you cover vent hole with your thumb. Repeat twice for a total of three primes. Fuel Valve OPEN Position Shown Fuel Tank Figure. Fuel Valve Positions Turn Valve Clockwise To OFF Position SLOW RUN FAST CHOKE PRIMER Figure 6. Typical Engine Symbols DO NOT use primer bulb to restart a warm engine after a short shutdown. Doing so will flood the engine and may result in equipment malfunction. If restarting a warm engine after a short shutdown, move engine speed control to FAST position and move choke control to NO CHOKE position. See Figures 4, 6 and 7 starting on page. Afterward, continue reading instructions below. 6. Operate equipment control to release engine brake or clutch, if present (see equipment manufacturer s instructions).. Engine Speed Control. Position. SLOW Position 4. RUN Range. FAST Position 4 Figure 7. Engine Speed Control Positions. Primer Bulb. Vent Hole Figure 8. Pressing Primer Bulb Cycle Snow King Engine Page

16 When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury. To avoid this risk, carefully follow these instructions: 7. Grasp starter cord handle. See Figure 9. a. Pull rope out slowly until you feel drag. b. Without allowing the rope to retract, continue pulling rope with one rapid full arm stroke. c. Return rope slowly to original position. Following the instructions listed in the steps above avoids potential damage to the recoil mechanism. If recoil starter handle is frozen and will not operate engine, proceed as follows: a. Pull as much rope out of starter as possible. b. Release starter handle and let it snap back against starter to break up ice; these two steps should ONLY be done WHEN STARTER IS FROZEN. If engine fails to start after attempts repeat steps thru 7 and try again. 8. When engine starts: a. Momentarily move choke control to / CHOKE position until engine runs smoothly. See Figure 4 on page. Afterward, continue reading instructions below. b. Next, move choke control to NO CHOKE position. c. Finally, move engine speed control to desired speed in RUN range. See Figures 6 and 7 on page. Afterward, continue reading instructions below. Figure 9. Recoil Starter Handle If engine starts but falters when choke control is moved to NO CHOKE position: a. Momentarily move choke control back to FULL CHOKE position. b. Next, move choke control to / CHOKE position until engine runs smoothly. c. Finally, move choke control to NO CHOKE position. If engine dies after choke control is moved to NO CHOKE position repeat steps thru 8 to restart engine. 9. If engine fires but does not continue to run, move choke control to NO CHOKE position and start engine. See Figure 4 on page. Afterward, continue reading instructions below. 0. If engine fails to start after attempts in the NO CHOKE position, move choke control to FULL CHOKE position and start engine.. If engine does not start after following steps thru 0, contact your Authorized TecumsehPower Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way. Page 4 4-Cycle Snow King Engine 8-7-4

17 VI. Stopping Your Engine and Short-Term Storage Stop engine according to equipment manufacturer s instructions. To avoid unsupervised operation of an engine, especially by children, NEVER leave it unattended when it is running. Always turn off the engine after use and remove ignition key, if provided. Failure to do so may lead to serious injury or death. NEVER store engine with fuel in the fuel tank inside a building with potential sources of ignition such as hot water or space heaters, clothes dryers, electric motors, etc. Doing so may lead to an explosion resulting in death or serious injury. A. Stop Engine NOTE Run engine for a few minutes to help dry off any moisture on engine before proceeding to Step.. Move equipment control, if present (see manufacturer s instructions), engine control lever or ignition switch to or OFF position. See Figure. To avoid unsupervised operation of an engine, especially by children, NEVER leave it unattended when it is running. Always turn off the engine after use and remove ignition key, if provided. Failure to do so may lead to serious injury or death.. Remove ignition key, if provided (see manufacturer s instructions). See Figures 0 and. Figure 0. Ignition Key. Engine Speed Control. Position. SLOW Position 4. RUN Range. FAST Position Figure. Engine Speed Control Positions 4 NOTE Removing key will reduce the possibility of unauthorized starting of the engine while equipment is not in use.. Be sure fuel valve, if present (see equipment manufacturer s instructions) is in OFF position. See Figure 4 on page 6. Figure. Possible Ignition Key Locations Cycle Snow King Engine Page

18 B. After Engine is Stopped To prevent possible freeze-up of engine CAUTION controls, follow instructions with engine PED, listed below.. Wipe all snow and moisture from engine control lever and choke areas.. Move equipment control, if present (see manufacturer s instructions), engine control lever or ignition switch back and forth several times and leave control in or OFF position. See Figure.. Move engine choke back and forth several times and leave in the FULL CHOKE position. See Figure 4 on page. Afterward, continue reading instructions below. 4. Be sure fuel valve, if present (see equipment manufacturer s instructions) is in OFF position. See Figure 4. NEVER store engine with fuel in the fuel tank inside a building with potential sources of ignition such as hot water or space heaters, clothes dryers, electric motors, etc. Doing so may lead to an explosion resulting in death or serious injury.. Engine Speed Control. Position. SLOW Position 4. RUN Range. FAST Position Figure. Engine Speed Control Positions 4 Fuel Tank Fuel Valve OPEN Position Shown Turn Valve Clockwise To OFF Position Figure 4. Fuel Valve Positions Page 6 4-Cycle Snow King Engine 8-7-4

19 VII. Maintenance To avoid serious injury or death, an adult should perform maintenance on this engine. Only allow children to perform maintenance if an adult has determined they are experienced and capable of such operation. To prevent accidental starting when working on equipment, always: Carefully disconnect spark plug wire and keep it away from spark plug. See Figures and 6. Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. Carefully attach the spark plug wire to the grounding post, if provided. Disconnect battery at negative terminal first, if engine is equipped with a DC electric starter. Turn all engine switches to OFF position. Remove ignition key, if provided. When disconnecting power cord, always disconnect power cord from outlet first; then disconnect power cord from switch box on engine. See Figure 7. When connecting power cord, always connect power cord to switch box on engine first; then into outlet. See Figure 7. A. Remote Choke See equipment manufacturer s instructions and contact an Authorized TecumsehPower Servicing Dealer. B. Changing Oil To avoid engine damage, it is important to: Check oil level before each use and every operating hours when engine is warm. See A. Checking Oil Level instructions on page 4. Afterward, continue reading instructions below. Change oil after first operating hours and every operating hours thereafter. Engine should still be warm but NOT hot from recent use. To check oil on engines with an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions on page. To check oil on engines with an oil fill cap/plug, see "II. Oil Fill Cap/Plug" instructions on page. Figure. Disconnecting/Connecting Spark Plug Figure 6. Typical Spark Plug Connection 4. Power Cord to Outlet. Switch Box. Starter Button 4. Schuko Plug. Power Cord to Switch Box on Engine 6. Electric Starter Switch Box on Engine 6 0V AC 0V AC Figure 7. Electric Starter Connections Cycle Snow King Engine Page 7

20 I. Oil Fill Cap/Dipstick If your engine has an oil fill cap/dipstick go to step. If your engine does NOT have an oil fill cap/dipstick, see "II. Oil Fill Cap/Plug" instructions on page 0.. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 8 and 9. See G. Avoid Accidental Starts instructions on page. Afterward, continue reading instructions below. Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. Carefully attach the spark plug wire to the grounding post, if provided. Figure 8. Disconnecting/Connecting Spark Plug Figure 9. Typical Spark Plug Connection. Be sure fuel fill cap is on and tightened securely. See Figure 40. See Figure 4 on page 7. Afterward, continue reading instructions below. Figure 40. Fuel Fill Cap Angled Front View. Be sure you find the correct oil drain plug location, if present (see equipment manufacturer s instructions). See Figure 4. See Figure 4 on page 7. Afterward, continue reading instructions below. Back View 4. Clean area around oil drain plug.. Oil Fill Cap/Dipstick. Oil Fill Cap/Plug. Oil Drain Plug Figure 4. Oil Fill/Drain Locations Page 8 4-Cycle Snow King Engine 8-7-4

21 . Place approved recyclable oil container under oil drain plug, if present. See Figure 4 on page 8. Afterward, continue reading instructions below. 6. Remove oil drain plug, if present. 7. Tip engine to position the oil flow, so it will drain from the lowest point on the engine (see equipment manufacturer s instructions). 8. Drain oil into an approved recyclable oil container. OH8SA/OH8SA OH9SA/OH9SP NOTE Used oil must be disposed of at a proper collection center. 9. Install oil drain plug and tighten securely. 0. Clean area around oil drain plug. See Figure 4 on page 8. Afterward, continue reading instructions below.. Remove oil fill cap/dipstick. See Figure 4.. Fill with recommended oil. See Figure 4. See "III. Oil and Fuel Specifications" instructions on page 4. See Table on page 4. Afterward, continue reading instructions below. DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. DO NOT allow oil level to fall below the ADD mark on oil fill cap/dipstick. Doing so may result in equipment malfunction or damage. Contact your Authorized TecumsehPower Servicing Dealer for TecumsehPower oil.. Wipe away any spilled oil. 4. Install oil fill cap/dipstick. Tighten securely. See Figure 4.. Carefully disconnect spark plug wire from grounding post, if provided. See Figures 8 and 9 on page 8. See "G. Avoid Accidental Starts" instructions on page. Afterward, continue reading instructions below. 6. Connect spark plug wire to spark plug before attempting to start engine. See Figures 8 and 9 on page 8. LH9SA/LH9SP Figure 4. Oil Fill Cap/Dipstick Locations FULL OK ADD LH8SA/LH8SA Fill Between FULL and ADD Marks Figure 4. Engine Oil Level Cycle Snow King Engine Page 9

22 II. Oil Fill Cap/Plug If your engine does NOT have an oil fill cap/dipstick, go to step. If your engine has an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions on page 8. Figure 44. Disconnecting/Connecting Spark Plug. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 44 and 4. See "G. Avoid Accidental Starts" instructions on page. Afterward, continue reading instructions below. Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. Carefully attach the spark plug wire to the grounding post, if provided. Figure 4. Typical Spark Plug Connection. Be sure fuel fill cap is on and tightened securely. See Figure 46. Figure 46. Fuel Fill Cap Angled Front View. Be sure you find the correct oil drain plug location (see equipment manufacturer s instructions). See Figure Clean area around oil drain plug.. Oil Fill Cap/Plug. Oil Drain Plug Back View Figure 47. Oil Fill/Drain Locations Page 0 4-Cycle Snow King Engine 8-7-4

23 . Place approved recyclable oil container under oil drain plug. See Figures 47 and 48 starting on page 0. Afterward, continue reading instructions below. 6. Tip engine to position the oil drain plug at the lowest point on the engine (see equipment manufacturer s instructions). 7. Remove oil drain plug and drain oil into an approved recyclable oil container. NOTE Used oil must be disposed of at a proper collection center. 8. Install oil drain plug and tighten securely. See Figure Remove oil fill cap/plug from oil fill hole. See Figures 47 and 48 starting on page 0. Afterward, continue reading instructions below. See "III. Oil and Fuel Specifications" instructions on page 4. Afterward, continue reading instructions below. See Table on page 4. Afterward, continue reading instructions below. 0. Add oil to overflow point, making sure to avoid spilling and fill with recommended oil. DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. Contact your Authorized TecumsehPower Servicing Dealer for TecumsehPower Oil.. Wipe away any spilled oil.. Screw oil fill cap/plug back into oil fill hole. Tighten securely. See Figures 47 and 48 starting on page 0. Afterward, continue reading instructions below.. Carefully disconnect spark plug wire from grounding post, if provided. 4. Connect spark plug wire to spark plug before attempting to start engine. C. Spark Plug Check spark plug yearly or every 00 operating hours.. Clean area around spark plug.. Remove and inspect spark plug.. Replace spark plug if porcelain is cracked or if electrodes are: Pitted Burned Fouled with Deposits 4. Check electrode gap with wire feeler gauge and set gap to.00 in. (0.76 mm) if necessary. See Figure.. Oil Fill Cap/Plug. Oil Drain Plug Figure 48. Oil Fill Cap/Plug and Oil Drain Plug Figure 49. Disconnecting/Connecting Spark Plug Figure 0. Typical Spark Plug Connection Figure. Resistor Spark Plugs. Install spark plug and tighten securely. NOTE A resistor spark plug must be used for replacement. Contact your Authorized TecumsehPower Servicing Dealer for a genuine replacement Resistor Spark Plug Cycle Snow King Engine Page..00 in. (0.76 mm) Gap. Electrodes. Porcelain OHV Plug L-Head Plug

24 D. Carburetor If you think your carburetor needs adjusting, see your nearest Authorized TecumsehPower Servicing Dealer. Engine performance should not be affected at altitudes up to 7,000 feet (,4 meters). For operation at higher elevations, contact an Authorized TecumsehPower Servicing Dealer. E. Alternator (Optional) For alternator related electrical problems such as: Inoperative Starter Discharged Battery Fuse Replacement Alternator Maintenance/Repairs See your equipment manufacturer s instructions and an Authorized TecumsehPower Servicing Dealer. F. Engine Speed To avoid serious injury or death, DO NOT modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. NEVER tamper with factory setting of engine governor. Running the engine faster than the speed set at the factory can be dangerous and will VOID THE ENGINE WARRANTY. G. Removing Snow from Engine After each use, remove snow from the areas listed. See Figure on page. Afterward, continue reading instructions below. Oil Fill Cap/Dipstick Fuel Fill Cap Recoil Starter/Flywheel Screen Linkage Guards Spark Plug Connection (If visible). Electric Starter Switch Box, if present (see equipment manufacturer s instructions). See "A. Engines with Electric Starters" instructions on page 0. Afterward, continue reading instructions below. VIII. Transporting Your Engine NEVER transport this engine inside another vehicle or in any enclosed space if there is any gasoline in the tank. Fuel vapor or spilled fuel may ignite leading to serious injury or death. If there is fuel in the fuel tank, close the fuel shut-off valve, if equipped, and transport the engine upright in an open vehicle, such as an open trailer or open bed of a pickup truck. If you DO NOT have an open vehicle and have to transport the engine upright in a closed vehicle, follow these steps for emptying the fuel tank before transporting:. Empty fuel tank by using a commercially available suction device designed for use with gasoline. To avoid serious injury or death, DO NOT pour fuel from engine or siphon fuel by mouth.. Drain fuel into an approved red GASOLINE container, being careful to avoid spilling.. Run the engine until remaining fuel is consumed. NEVER leave the engine unattended when it is running and NEVER run engine in enclosed areas to avoid death or serious injury. See equipment manufacturer s instructions for proper location of fuel fill cap and control lever. Removing snow will ease operation of the recoil starter rope and reduce the risk of water contamination when opening fuel fill cap. For more information about recoil starters see "B. Engines with Recoil Starters" instructions on page. Page 4-Cycle Snow King Engine 8-7-4

25 4 4 OH8SA/OH8SA OH9SA/OH9SP 4 4 LH9SA/LH9SP LH8SA/LH8SA. Oil Fill Cap/Dipstick. Fuel Fill Cap Areas. Recoil Starter/Flywheel Guard Areas 4. Linkage Areas. Spark Plug Connection Figure. Snow and Debris Removal Locations Cycle Snow King Engine Page

26 IX. Storing Your Engine A. Short-Term/Seasonal Storage I. Clean Engine Before servicing the engine remove the carburetor cover and/or blower housing. Remove dirt and debris from the following areas: Cooling Fins Air Intake Screen or Recoil Starter/ Flywheel Guard Areas Oil Fill Cap/Dipstick Fuel Fill Cap Areas Spark Plug Connection Levers Linkage Area Guards Carburetor Head Removing debris will insure adequate cooling, correct engine speed and reduce the risk of fire. II. Fuel Storage NEVER store engine with fuel in the fuel tank inside a building with potential sources of ignition such as hot water or space heaters, clothes dryers, electric motors, etc. Doing so may lead to an explosion resulting in death or serious injury. If engine fuel stored in the gas tank and/or an approved gas container is to be unused without gasoline stabilizer for more than -0 days, prepare it for short-term/seasonal storage. See "IV. Fuel Treatment" instructions. Afterward, continue reading instructions below. If engine fuel is to be stored for more than one season, without gasoline stabilizer, it will gradually deteriorate. Also, if it is stored in the engine s gas tank without gasoline stabilizer it is likely that your carburetor will have gum deposits, a clogged fuel system and WILL VOID YOUR WARRANTY. Prepare the fuel for extended storage. See "B. Extended Storage" instructions. Afterward, continue reading instructions. III. Fuel System To avoid stale gas and carburetor problems, treat the fuel system in the following method below: TecumsehPower Company recommends using ULTRA-FRESH Gasoline Stabilizer as an acceptable method of minimizing formation of fuel gum deposits during storage. This product is available from your Authorized TecumsehPower Servicing Dealer. Always follow mix ratio found on stabilizer container. Failure to do so may result in equipment damage. It is NOT necessary to empty stabilized gas from fuel tank. IV. Fuel Treatment. Add fuel stabilizer according to manufacturer s instructions.. Run engine at least 0 minutes after adding stabilizer to allow it to reach carburetor. NEVER store engine with fuel in fuel tank inside a building with potential sources of ignition such as hot water and space heaters, clothes dryers, electric motors, etc. Doing so may result in an explosion and result in death or serious injury. NOTE Instead of using a fuel preservative/stabilizer, you can empty the fuel tank as described under "I. Draining Fuel" instructions. See "B. Extended Storage" instructions. B. Extended Storage I. Draining Fuel Clean debris from engine before emptying fuel from fuel tank. See "I. Clean Engine" instructions. Afterward, continue reading instructions below. If you have prepared your fuel for short-term storage it is NOT necessary to empty fuel that contains stabilizer from your fuel tank. See "A. Short-Term/Seasonal Storage" instructions. Afterward, continue reading instructions below. To avoid severe injury or death, DO NOT pour fuel from engine or siphon fuel by mouth.. To prevent serious injury from fuel fires, empty fuel tank by running engine until it stops from lack of fuel. DO NOT attempt to pour fuel from engine.. Run the engine while waiting until the remaining fuel is consumed. NEVER leave the engine unattended when it is running and NEVER run engine in enclosed areas to avoid death or serious injury.. Begin servicing the cylinder bore. See "II. Oil Cylinder Bore" instructions on page. Page 4 4-Cycle Snow King Engine 8-7-4

27 II. Oil Cylinder Bore CAUTION When lubricating cylinder bore, fuel may spray from spark plug hole. To prevent serious injury from fuel fires, follow these instructions:. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures and 4. Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. Carefully attach the spark plug wire to the grounding post, if provided. Disconnect battery at negative terminal first, if engine is equipped with a DC electric starter. Turn all engine switches to OFF position. Remove ignition key, if provided.. Remove spark plug.. Squirt oz. (0 ml) of clean engine oil into spark plug hole. 4. Cover spark plug hole with rag to prevent fuel from spraying from spark plug hole when starter rope is pulled. For engines equipped with recoil starters proceed to Step. For engines equipped with electric starters proceed to Step 6.. Grasp starter cord handle: a. Pull starter cord handle out slowly using a full arm stroke. b. Repeat once. (This will distribute oil throughout the cylinder to prevent corrosion during storage.) c. Proceed to Step Push starter button or turn ignition switch key to START position. Immediately release starter button or turn ignition switch key to OFF position. (This will distribute oil throughout the cylinder to prevent corrosion during storage.) 7. Remove rag covering spark plug hole. 8. Install spark plug. 9. Carefully disconnect spark plug wire from grounding post, if provided. See Figure. 0. Connect spark plug wire to spark plug before attempting to start engine. See Figure 4. Figure. Disconnecting/Connecting Spark Plug Figure 4. Typical Spark Plug Connection III. Oil Change oil if NOT changed within the last months. See "B. Changing Oil" instructions on page 7. IV. Battery See equipment manufacturer s instructions for proper battery storage if machine is equipped with a battery Cycle Snow King Engine Page

4-Cycle Snow King Engine Operator s Manual

4-Cycle Snow King Engine Operator s Manual 4-Cycle Snow King Engine Operator s Manual Horizontal Crankshaft Air-Cooled LH9SA/LH9SP LH8SA/LH8SA OH9SA/OH9SP OH8SA/OH8SA ENGINE MODEL: SPEC: D.O.M.: Visit our web site at www.tecumsehpower.com Register

More information

LV148EA/LV148XA LV156EA/LV156XA LV195EA/LV195XA (LEV90-120)

LV148EA/LV148XA LV156EA/LV156XA LV195EA/LV195XA (LEV90-120) LV48EA/LV48XA LV56EA/LV56XA LV95EA/LV95XA (LEV90-0) Four-Cycle Engine Vertical Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions...ii I. General Safety Precautions... II. How

More information

Operator s Manual OV195EA/OV195XA. Four-Cycle Engine Vertical Crankshaft Air-Cooled. Table of Contents

Operator s Manual OV195EA/OV195XA. Four-Cycle Engine Vertical Crankshaft Air-Cooled. Table of Contents Operator s Manual OV95EA/OV95XA Four-Cycle Engine Vertical Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions...ii I. General Safety Precautions... II. How to Get Service... 3

More information

Operator s Manual OH318EA (OHM90-110) Four-Cycle Engine Horizontal Crankshaft Air-Cooled

Operator s Manual OH318EA (OHM90-110) Four-Cycle Engine Horizontal Crankshaft Air-Cooled s Operator s Manual OH318EA (OHM90-110) Four-Cycle Engine Horizontal Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions... ii I. General Safety Precautions... 1 II. How to Get

More information

Operator s Manual LH318XA (HM80-100) LH358EA/LH358XA. Four-Cycle Engine L-Head Horizontal Crankshaft Air-Cooled. Table of Contents

Operator s Manual LH318XA (HM80-100) LH358EA/LH358XA. Four-Cycle Engine L-Head Horizontal Crankshaft Air-Cooled. Table of Contents Operator s Manual LH8XA (HM80-00) LH58EA/LH58XA Four-Cycle Engine L-Head Horizontal Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions... ii I. General Safety Precautions... II.

More information

Operator s Manual OH195EA/OH195XA (OHH50-65) OH195EP/OH195XP. Four-Cycle Engine Horizontal Crankshaft Air-Cooled.

Operator s Manual OH195EA/OH195XA (OHH50-65) OH195EP/OH195XP. Four-Cycle Engine Horizontal Crankshaft Air-Cooled. Operator s Manual OH195EA/OH195XA (OHH50-65) OH195EP/OH195XP Four-Cycle Engine Horizontal Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions...ii I. General Safety Precautions...

More information

OH195EA/OH195XA OH195EP/OH195XP

OH195EA/OH195XA OH195EP/OH195XP Operator s Manual OH195EA/OH195XA OH195EP/OH195XP Four-Cycle Engine Horizontal Crankshaft Air-Cooled Table of Contents Safety Definitions...ii I. General Safety Precautions... 1 II. How to Get Service...

More information

TVM220. Operator s Manual

TVM220. Operator s Manual TecumsehPower TVM220 Operator s Manual Four-Cycle L-Head Engine Vertical Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions...ii I. General Safety Precautions... 1 II. How to

More information

OHV Operator s Manual. Four-Cycle Vertical Crankshaft Air-Cooled. Table of Contents

OHV Operator s Manual. Four-Cycle Vertical Crankshaft Air-Cooled. Table of Contents OHV 110-135 Operator s Manual Four-Cycle Vertical Crankshaft Air-Cooled Table of Contents Important Notice! Safety Definitions... ii I. General Safety Precautions... 1 II. How to Get Service... 3 III.

More information

Safe Operation Practices Set-Up Operation Maintenance Troubleshooting Warranty OPERATOR S MANUAL. 277cc, 357cc & 420cc OHV Horizontal Shaft Engine

Safe Operation Practices Set-Up Operation Maintenance Troubleshooting Warranty OPERATOR S MANUAL. 277cc, 357cc & 420cc OHV Horizontal Shaft Engine Safe Operation Practices Set-Up Operation Maintenance Troubleshooting Warranty OPERATOR S MANUAL 277cc, 357cc & 420cc OHV Horizontal Shaft Engine WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS

More information

Part No FJ180V KAI. 4-stroke air-cooled gasoline engine OWNER, S MANUAL

Part No FJ180V KAI. 4-stroke air-cooled gasoline engine OWNER, S MANUAL Part No. 99920-2280-02 FJ180V KAI 4-stroke air-cooled gasoline engine OWNER, S MANUAL SAFETY AWARENESS FOREWORD TABLE OF CONTENTS Whenever you see the symbols shown below, heed their instructions! Always

More information

Operator s Manual TM049XA. Two-Cycle Engine Horizontal/Vertical Crankshaft Air-Cooled. Table of Contents

Operator s Manual TM049XA. Two-Cycle Engine Horizontal/Vertical Crankshaft Air-Cooled. Table of Contents Operator s Manual TM049XA Two-Cycle Engine Horizontal/Vertical Crankshaft Air-Cooled Table of Contents IMPORTANT NOTICE! Safety Definitions...ii I. General Safety Precautions... 1 II. How to Get Service...

More information

Owner s/operator s Manual

Owner s/operator s Manual Water Pump MP2533E2 Owner s/operator s Manual Completely read and understand this manual before using this product. Foreword This Owner s/ Operator s Manual is designed to familiarize the operator with

More information

OPERATING & PARTS MANUAL WP CC WATER PUMP

OPERATING & PARTS MANUAL WP CC WATER PUMP OPERATING & PARTS MANUAL WP4310 43CC WATER PUMP OMWP4310 Rev. 10/23/06 2006 Ardisam, Inc. All Rights Reserved. Printed in USA. EARTHQUAKE, Division of Ardisam, Inc. Page 2 INTRODUCTION, REGISTRATION AND

More information

Operation Manual. 21 Inch Self-Propelled Lawn Mower MODEL #

Operation Manual. 21 Inch Self-Propelled Lawn Mower MODEL # 21 Inch Self-Propelled Lawn Mower MODEL # 106461 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result

More information

EZT715-EZT750 Owner's Manual

EZT715-EZT750 Owner's Manual EN EZT715-EZT750 Owner's Manual ESS FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

MODELS OHH45, OHH50, OHH55, OHH60, OHH65

MODELS OHH45, OHH50, OHH55, OHH60, OHH65 OPERATOR'S MANUAL and MAINTENANCE INSTRUCTIONS for TECUMSEH MODELS OHH45, OHH50, OHH55, OHH60, OHH65 HORIZONTAL CRANKSHAFT AIR COOLED FOUR-CYCLE ENGINE THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS

More information

HD675, HD775 Owner's Manual

HD675, HD775 Owner's Manual EN ESS HD675, HD775 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

ZT710-ZT740 Owner's Manual

ZT710-ZT740 Owner's Manual EN ZT710-ZT740 Owner's Manual ESS FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

Water pump Owner's Manual

Water pump Owner's Manual Water pump Owner's Manual Safety Precautions I. General Safeguards Please read this operation manual to have a thorough understanding of the content there before use the product. Failure to do so may lead

More information

TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL

TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT IS

More information

8500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL

8500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL 8500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT

More information

Earth Auger MAG500 MAG500RS

Earth Auger MAG500 MAG500RS Earth Auger MAG500 MAG500RS US Owner s/operator s Manual Completely read and understand this manual before using this product. - 0 - Foreword This Owner s/ Operator s Manual is designed to familiarize

More information

9500M. WARNING American Fab of SC, LLC Travelers Rest, SC OPERATOR S MANUAL INDUSTRIAL GASOLINE GENERATOR

9500M. WARNING American Fab of SC, LLC Travelers Rest, SC OPERATOR S MANUAL INDUSTRIAL GASOLINE GENERATOR 9500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL WARNING American Fab of SC, LLC Travelers Rest, SC It is extremely important to read and understand the entire contents of this operator s manual before

More information

KT715-KT745 Owner's Manual

KT715-KT745 Owner's Manual EN KT715-KT745 Owner's Manual ESS FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

XTX650, XTX675, XTX775, XTX950, XTX1100 Owner's Manual

XTX650, XTX675, XTX775, XTX950, XTX1100 Owner's Manual EN ESS XTX650, XTX675, XTX775, XTX950, XTX1100 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment

More information

1-1/2 DIAMETER WATER PUMP

1-1/2 DIAMETER WATER PUMP 1-1/2 DIAMETER WATER PUMP 2.2HP/79.8cc Engine MODEL # 101099 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information

More information

LAWN MOWER OWNER S MANUAL

LAWN MOWER OWNER S MANUAL LAWN MOWER OWNER S MANUAL Woodies SKU: 1153279 & 1153280 CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment Thank you for choosing our Gasoline Lawnmower. 1 To ensure

More information

IMPORTANT INFORMATION

IMPORTANT INFORMATION Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications................................ 1B-1 Special Tools................................ 1B-2 Quicksilver Lubricant/Sealant..................

More information

1100W PORTABLE GENERATOR

1100W PORTABLE GENERATOR 1100W PORTABLE GENERATOR MODEL NO: G1200 PART NO: 8010110 OPERATION & MAINTENANCE INSTRUCTIONS LS0312 INTRODUCTION Thank you for purchasing this CLARKE 1100W Portable Generator. Before attempting to use

More information

Make/Type/Size/Model Honda Generator EB 3500X & EB5000X Operators Manual Open Well Ventilated Area to Start & Shut Down Machine

Make/Type/Size/Model Honda Generator EB 3500X & EB5000X Operators Manual Open Well Ventilated Area to Start & Shut Down Machine HONDA GENERATORS ARE DESIGNED TO GIVE SAFE AND DEPENDABLE SERVICE IF OPERATED ACCORDING TO INSTRUCTIONS. YOU CAN HELP PREVENT ACCIDENTS BY BEING FAMILIAR WITH YOUR GENERATORS CONTROLS AND BY OBSERVING

More information

KS530-KS595 Owner's Manual

KS530-KS595 Owner's Manual EN ESS KS530-KS595 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

Table of Contents. Safety symbols... 3 Assembly 6. Operation Maintenance Troubleshooting 11. Storage. 12. Notes. 13

Table of Contents. Safety symbols... 3 Assembly 6. Operation Maintenance Troubleshooting 11. Storage. 12. Notes. 13 Table of Contents Safety symbols... 3 Assembly 6 Operation... 8 Maintenance... 10 Troubleshooting 11 Storage. 12 Notes. 13 2 Safety Information Attention; this machine can be dangerous! All operators should

More information

SV471-SV601 Owner's Manual

SV471-SV601 Owner's Manual EN ESS SV471-SV601 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

PF-4000, PF-4010, PF-4210 MULTI-PURPOSE ENGINE

PF-4000, PF-4010, PF-4210 MULTI-PURPOSE ENGINE PF-4000, PF-4010, PF-4210 MULTI-PURPOSE ENGINE Date 09-26-01 Supplier To The Outdoor Power Equipment Industry ISM, Inc. 1028 4 th Street SW Auburn, WA 98001 Phone: (253) 333-1200 Fax: (253) 333-1212 WWW.TANAKA-USA.COM

More information

YK1900i DIGITAL INVERTER GASOLINE GENERATOR OWNER S MANUAL PLEASE READ THIS MANUAL CAREFULLY. IT CONTAINS IMPORTANT SAFETY INFORMATION.

YK1900i DIGITAL INVERTER GASOLINE GENERATOR OWNER S MANUAL PLEASE READ THIS MANUAL CAREFULLY. IT CONTAINS IMPORTANT SAFETY INFORMATION. YK1900i DIGITAL INVERTER GASOLINE GENERATOR OWNER S MANUAL PLEASE READ THIS MANUAL CAREFULLY. IT CONTAINS IMPORTANT SAFETY INFORMATION. PREFACE Thank you for purchasing YANGKE generator. This manual covers

More information

OPERATOR'S MANUAL TECUMSEH MODELS HSK845, 850, SNOW BLOWER ENGINE HORIZONTAL CRANKSHAFT AIR COOLED -TWO-CYCLE ENGINE

OPERATOR'S MANUAL TECUMSEH MODELS HSK845, 850, SNOW BLOWER ENGINE HORIZONTAL CRANKSHAFT AIR COOLED -TWO-CYCLE ENGINE OPERATOR'S MANUAL and MAINTENANCE INSTRUCTIONS for TECUMSEH HSK600 MODELS HSK845, 850, 600 HSK845/850 SNOW BLOWER ENGINE HORIZONTAL CRANKSHAFT AIR COOLED -TWO-CYCLE ENGINE THIS SYMBOL POINTS OUT IMPORTANT

More information

KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. WARRANTY & SERVICE INFORMATION 1-YEAR LIMITED WARRANTY FOR THIS 950W

More information

5.5KVA GENERATOR MODEL NO: PG6500DVES OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0616

5.5KVA GENERATOR MODEL NO: PG6500DVES OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0616 5.5KVA GENERATOR MODEL NO: PG6500DVES PART NO: 8857810 OPERATION & MAINTENANCE INSTRUCTIONS LS0616 INTRODUCTION Thank you for purchasing this CLARKE 5.5KVA Generator. Before attempting to use this product,

More information

1200W INVERTER GENERATOR

1200W INVERTER GENERATOR 1200W INVERTER GENERATOR MODEL NO: IG1200 PART NO: 8877070 OPERATION & MAINTENANCE INSTRUCTIONS LS0117 INTRODUCTION Thank you for purchasing this CLARKE 1200W Inverter Generator. Before attempting to use

More information

9000RC INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL

9000RC INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL 9000RC INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT

More information

Operator's Manual WP cc Water Pump ARDISAM. .com. OMWP4310 Rev Ardisam, Inc. All Rights Reserved.

Operator's Manual WP cc Water Pump ARDISAM. .com. OMWP4310 Rev Ardisam, Inc. All Rights Reserved. WP4310 43cc Water Pump ARDISAM.com OMWP4310 Rev. 12-17-09 2009 Ardisam, Inc. All Rights Reserved. INTRODUCTION, REGISTRATION AND WARRANTY Thank You... for purchasing an Earthquake TM Water Pump from Ardisam,

More information

AND OPERATING INSTRUCTIONS IMPORTANT:

AND OPERATING INSTRUCTIONS IMPORTANT: WOOD CHIPPER User Manual FM6.5WC SAFETY AND OPERATING INSTRUCTIONS IMPORTANT: Read safety rules and instructions carefully before operating equipment. Table of Contents Table of Contents PART I: General

More information

TWPUMP. 2-Inch (50mm) Semi Trash / Water Pump Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

TWPUMP. 2-Inch (50mm) Semi Trash / Water Pump Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. TWPUMP 2-Inch (50mm) Semi Trash / Water Pump Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation

More information

CH940-CH1000 CV940-CV1000 Owner's Manual

CH940-CH1000 CV940-CV1000 Owner's Manual CH940-CH1000 CV940-CV1000 Owner's Manual IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers.

More information

PW2750 HOT WATER HI PRESSURE WASHER INSTRUCTION MANUAL

PW2750 HOT WATER HI PRESSURE WASHER INSTRUCTION MANUAL 4/10/2012 PW2750 HOT WATER HI PRESSURE WASHER INSTRUCTION MANUAL READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

FORZA BOLT OUTBOARD MOTOR OWNER S MANUAL

FORZA BOLT OUTBOARD MOTOR OWNER S MANUAL FORZA BOLT OUTBOARD MOTOR OWNER S MANUAL Table Of Contents 1.Introduction...1 2.Safety Information.1 3.Refuelling Information...1 4.Safety Matters 2 5.Preparation.3 6.Operation.3 7.Maintenance...4 8.Storage...5

More information

AC2T & AC2T-ES INDUSTRIAL GASOLINE AIR COMPRESSOR

AC2T & AC2T-ES INDUSTRIAL GASOLINE AIR COMPRESSOR AC2T & AC2T-ES INDUSTRIAL GASOLINE AIR COMPRESSOR INDUSTRIAL GAS AIR COMPRESSOR OPERATOR S MANUAL IT IS ETREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING

More information

3KVA DUAL VOLTAGE GENERATOR MODEL NO: PG3800DV

3KVA DUAL VOLTAGE GENERATOR MODEL NO: PG3800DV 3KVA DUAL VOLTAGE GENERATOR MODEL NO: PG3800DV PART NO: 8857815 OPERATION & MAINTENANCE INSTRUCTIONS LS1016 INTRODUCTION Thank you for purchasing this CLARKE 3KVA Dual Voltage Generator. Before attempting

More information

GEN2000 i 2,000 MAX WATTS INVERTER GENERATOR INSTRUCTION MANUAL

GEN2000 i 2,000 MAX WATTS INVERTER GENERATOR INSTRUCTION MANUAL GEN2000 i 2,000 MAX WATTS INVERTER GENERATOR INSTRUCTION MANUAL READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

SERVICE MANUAL COMMAND CV11-16, CV , CV VERTICAL CRANKSHAFT

SERVICE MANUAL COMMAND CV11-16, CV , CV VERTICAL CRANKSHAFT COMMAND CV-6, CV460-465, CV490-495 SERVICE MANUAL VERTICAL CRANKSHAFT Section CV-6 Safety and CV460-465, General Information CV490-495 Section Safety Precautions To insure safe operations please read the

More information

720W PORTABLE GENERATOR

720W PORTABLE GENERATOR 720W PORTABLE GENERATOR MODEL NO: G720 PART NO: 8857800 OPERATION & MAINTENANCE INSTRUCTIONS LS0214 INTRODUCTION Thank you for purchasing this CLARKE 720W Portable Generator Before attempting to use this

More information

GASOLINE GENERATOR SET SPG8000 PORTABLE GENERATOR INSTRUCTION MANUAL IMPORTANT!

GASOLINE GENERATOR SET SPG8000 PORTABLE GENERATOR INSTRUCTION MANUAL IMPORTANT! GASOLINE GENERATOR SET SPG8000 PORTABLE GENERATOR INSTRUCTION MANUAL IMPORTANT! Please make certain that persons who are to use this equipment thoroughly read and understand these instructions and any

More information

operation manual Model Numbers MC3100PR MC6500ER MC9000ER

operation manual Model Numbers MC3100PR MC6500ER MC9000ER operation manual Model Numbers MC3100PR MC6500ER MC9000ER table of contents Introduction 4 Using the Operators Manual Product Identification 5 Generator 5 Engine Safety 6 Safety Rules 6 Hazard Symbols

More information

Introduction. Power Clear 721 Snowthrower Model No Serial No and Up Model No Serial No and Up.

Introduction. Power Clear 721 Snowthrower Model No Serial No and Up Model No Serial No and Up. Power Clear 721 Snowthrower Model No. 38741 Serial No. 402082000 and Up Model No. 38742 Serial No. 402082000 and Up Form No. 3415-621 Rev B Operator's Manual Introduction This machine is intended to be

More information

Operation Manual. All Terrain Power Cart MODEL #

Operation Manual. All Terrain Power Cart MODEL # All Terrain Power Cart MODEL # 101872 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious

More information

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications SERVICE PROCEDURES AND SPECIFICATIONS Engine SECTION 6 2 Specifications........................................... 162 Fuel.................................................... 164 Facts about engine oil

More information

PORTABLE TRASH PUMPS MDP200

PORTABLE TRASH PUMPS MDP200 PORTABLE TRASH PUMPS MDP200 OPERATING & PARTS MANUAL INTRODUCTION This manual provides information and procedures to safely operate and maintain the engine and pump. For your own safety and protection

More information

PORTABLE INVERTER GENERATOR MODEL

PORTABLE INVERTER GENERATOR MODEL 3200Watts PORTABLE INVERTER GENERATOR MODEL #104612 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may

More information

GENERATOR MODEL NO: FG2500 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0114

GENERATOR MODEL NO: FG2500 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0114 GENERATOR MODEL NO: FG2500 PART NO: 8857727 OPERATION & MAINTENANCE INSTRUCTIONS LS0114 INTRODUCTION Thank you for purchasing this CLARKE Generator. Before attempting to use this product, please read this

More information

KT610-KT620, KT715-KT745 Owner's Manual

KT610-KT620, KT715-KT745 Owner's Manual EN ESS FRC KT610-KT620, KT715-KT745 Owner's Manual IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine

More information

Engine Owner s Manual. Models sx4000, i4000, i4500, i5000, i5500, i7000 & i7000xt. Operating & Maintenance Instructions

Engine Owner s Manual. Models sx4000, i4000, i4500, i5000, i5500, i7000 & i7000xt. Operating & Maintenance Instructions Engine Owner s Manual Models sx4000, i4000, i4500, i5000, i5500, i7000 & i7000xt Operating & Maintenance Instructions BEFORE OPERATING ENGINE Read entire Operating & Maintenance Instructions AND the instructions

More information

Gasoline Inverter Generator

Gasoline Inverter Generator user manual Gasoline Inverter Generator table of contents Preface Introduction... Safety Information Exhaust fumes are poisonous... Fuel is highly flammable and poisonous... Engine and muffler may be hot...

More information

MTD OHV Series I15 FORM NO I. MTD Products Aktiengesellschaft Saarbrücken Germany

MTD OHV Series I15 FORM NO I. MTD Products Aktiengesellschaft Saarbrücken Germany MTD OHV Series I15 FORM NO. 769-01577I MTD Products Aktiengesellschaft Saarbrücken Germany 8 15 23 31 38 46 54 61 68 75 82 90 99 107 115 122 130 138 145 152 159 166 175 183 193 202 211 218 226 English

More information

RedGum GP160 Splitter. Owner s Manual

RedGum GP160 Splitter. Owner s Manual RedGum GP160 Splitter Owner s Manual Product Description & Intended Purpose: This Log Splitter / Wood Splitter is an outdoor product that splits wood logs for use as fuel in a fireplace or a woodstove.

More information

950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS. MODELS #104609, # and #

950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS. MODELS #104609, # and # 950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS MODELS #104609, #104610 and #104611 Operation Manual This safety alert symbol identifies important safety messages

More information

General Power Products

General Power Products Portable Electric Generator Owners Manual MODEL: APP 6000 General Power Products IMPORTANT Please make certain the person who uses this Generator thoroughly reads these instructions and all other instructions

More information

Operation Manual. 10 Mini-Cultivator MODEL #

Operation Manual. 10 Mini-Cultivator MODEL # 10 Mini-Cultivator MODEL # 103350 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious

More information

PORTABLE TRASH PUMPS MTP200 MTP300 MTP400

PORTABLE TRASH PUMPS MTP200 MTP300 MTP400 PORTABLE TRASH PUMPS MTP200 MTP300 MTP400 OPERATING & PARTS MANUAL INTRODUCTION This manual provides information and procedures to safely operate and maintain the engine and pump. For your own safety and

More information

GENERATOR MODEL NO: FG3005 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0413

GENERATOR MODEL NO: FG3005 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0413 GENERATOR MODEL NO: FG3005 PART NO: 8857707 OPERATION & MAINTENANCE INSTRUCTIONS LS0413 INTRODUCTION Thank you for purchasing this CLARKE Generator. Before attempting to use this product, please read this

More information

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications

SECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications SERVICE PROCEDURES AND SPECIFICATIONS Engine SECTION 6 2 Specifications........................................... 170 Fuel.................................................... 172 Facts about engine oil

More information

Owner s Manual. GENERATOR EU2000i. o Honda Motor Co., Ltd. -All Rights Reserved. See page 82 for Initial Use Instructions

Owner s Manual. GENERATOR EU2000i. o Honda Motor Co., Ltd. -All Rights Reserved. See page 82 for Initial Use Instructions Owner s Manual GENERATOR EU2000i o2001-2009 Honda Motor Co., Ltd. -All Rights Reserved See page 82 for Initial Use Instructions The engine exhaust from this product contains chemicals known to the State

More information

GENERATOR MODEL NO: FG3000 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0609

GENERATOR MODEL NO: FG3000 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0609 GENERATOR MODEL NO: FG3000 PART NO: 8857700 OPERATION & MAINTENANCE INSTRUCTIONS LS0609 INTRODUCTION Thank you for purchasing this CLARKE Generator. Before attempting to use this product, please read this

More information

ENGINE DRIVEN 3 FULL TRASH PUMP

ENGINE DRIVEN 3 FULL TRASH PUMP ENGINE DRIVEN 3 FULL TRASH PUMP MODEL NO: PF75 PART NO: 7230165 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0117 ISS 2 INTRODUCTION Thank you for choosing this Clarke Pump. The function

More information

OWNER S MANUAL Assembly & Operating Instructions

OWNER S MANUAL Assembly & Operating Instructions OWNER S MANUAL Assembly & Operating Instructions BBT 71CC Post Hole Digger MODEL NO. BBT-PHD-71CC To The Owner Thank you for purchasing our Post Hole Digger. It was carefully engineered to provide excellent

More information

ECV850, ECV860, ECV870, ECV880 Owner's Manual

ECV850, ECV860, ECV870, ECV880 Owner's Manual EN ESS ECV850, ECV860, ECV870, ECV880 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this

More information

OWNER S MANUAL MODEL TTP-300 3X3 Commercial Trash Pump

OWNER S MANUAL MODEL TTP-300 3X3 Commercial Trash Pump OWNER S MANUAL MODEL TTP-300 3X3 Commercial Trash Pump P. O.Box 791, Travelers Rest, S.C. 29690 Phone 864-834-7212 Service/Replacement Parts 800-845-4141 WWW.TITANINDUSTRIAL.NET WARNING! Do Not Operate

More information

CH682, CH732, CH742, CH752 CV682, CV732, CV742, CV752 Owner's Manual

CH682, CH732, CH742, CH752 CV682, CV732, CV742, CV752 Owner's Manual EN ESS CH682, CH732, CH742, CH752 CV682, CV732, CV742, CV752 Owner's Manual FRC IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction

More information

AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL. This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E

AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL. This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E TDG8000-3 TDG7000SE-3 TDG7000E TDG8000E TDGW7000SE TDG7000E3 TDGW8000E

More information

Log Splitter. Owner/Operator Manual. Models HCWP1-26

Log Splitter. Owner/Operator Manual. Models HCWP1-26 Log Splitter Owner/Operator Manual Models HCWP1-26 SAFETY..........................2 SAFETY WARNING SYMBOL.........3 SAFETY RULES.................. 4-5 SPECIFICATIONS................. 6 CONTROLS AND FEATURES.......

More information

Owner s Manual. GENERATOR EB2000i. o2013 Honda Motor Co., Ltd. -All Rights Reserved. See page 78 for Initial Use Instructions

Owner s Manual. GENERATOR EB2000i. o2013 Honda Motor Co., Ltd. -All Rights Reserved. See page 78 for Initial Use Instructions Owner s Manual GENERATOR EB2000i o2013 Honda Motor Co., Ltd. -All Rights Reserved See page 78 for Initial Use Instructions The engine exhaust from this product contains chemicals known to the State of

More information

1P88F-1 1P90F-1 1P92F-1. Owner's Manuel

1P88F-1 1P90F-1 1P92F-1. Owner's Manuel 1P88F-1 1P90F-1 1P92F-1 Owner's Manuel EN 1 TABLE OF CONTENTS 1. General information... 1 2. Safety regulations... 1 3. Components and controls... 2 4. What you need to know... 3 5. Standards of use...

More information

Owner s Manual. GENERATOR EU1000i. o2013 Honda Motor Co., Ltd. -All Rights Reserved. See page 84 for Initial Use Instructions

Owner s Manual. GENERATOR EU1000i. o2013 Honda Motor Co., Ltd. -All Rights Reserved. See page 84 for Initial Use Instructions Owner s Manual GENERATOR EU1000i o2013 Honda Motor Co., Ltd. -All Rights Reserved See page 84 for Initial Use Instructions The engine exhaust from this product contains chemicals known to the State of

More information

OPERATOR S MANUAL AV 520 AV600 MODEL

OPERATOR S MANUAL AV 520 AV600 MODEL OPERATOR S MANUAL and MAINTENANCE INSTRUCTIONS for TECUMSEH MODEL AV 50 AV600 INDUSTRIAL ENGINE VERTICAL CRANKSHAFT AIR COOLED TWO-CYCLE ENGINE THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH

More information

Böhler-AG GASOLINE GENERATOR

Böhler-AG GASOLINE GENERATOR Böhler-AG GASOLINE GENERATOR Instruction Manual The generator is a potential source of electrical shock if misused. Do not expose the generator to moisture, rain or snow. DO not let the generator get wet,

More information

OWNERS MANUAL. Product Support

OWNERS MANUAL. Product Support Product Support OWNERS MANUAL Product Information, Application, Service Info & Warranty Questions Please email us at support@duromaxgenerators.com or call (800) 629-3325 Monday Friday 6:00 am 6:00 pm (PST)

More information

Read instructions carefully and follow rules for safe operation. Failure to do so could result in serious injury. Fradan Manufacturing Corp.

Read instructions carefully and follow rules for safe operation. Failure to do so could result in serious injury. Fradan Manufacturing Corp. OPERATOR MANUAL FRADAN POWER BLOWERS Part No. 888-011-222-0 Read instructions carefully and follow rules for safe operation. Failure to do so could result in serious injury. Fradan Manufacturing Corp.

More information

Reproduction. Not for. Wiring Diagram. Model / Modelo Mfg. No. Description / Descripción

Reproduction. Not for. Wiring Diagram. Model / Modelo Mfg. No. Description / Descripción Wiring Diagram This generator is rated in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-94 (motor and generators). Questions? Help is just a moment away! Preguntas? La ayuda

More information

142F 144F GASOLINE ENGINE SM-142F-01A INSTRUCTION MANUAL

142F 144F GASOLINE ENGINE SM-142F-01A INSTRUCTION MANUAL 142F 144F GASOLINE ENGINE SM-142F-01A INSTRUCTION MANUAL Thank you for purchasing our engine. This manual covers the operation and maintenance of your engine. All information in this publication is base

More information

WARNING! Ensure that there are no naked flames around the product! Do not smoke while filling fuel and oil!

WARNING! Ensure that there are no naked flames around the product! Do not smoke while filling fuel and oil! Engine Oil and Fuel Engine Operation This product is equipped with a 4 stroke engine. Before operation you have to add proper fuel and engine oil. DO NOT MIXTURE THEM! 1. Place the product on a stable,

More information

GASOLINE GENERATOR SET USER S MANUAL

GASOLINE GENERATOR SET USER S MANUAL GASOLINE GENERATOR SET USER S MANUAL Foreword Thank you for purchasing our gasoline generator and hope that you will enjoy operating your unit, one of the finest models in the market. This Manual provides

More information

SH255, SH265 Owner's Manual

SH255, SH265 Owner's Manual EN DE SH255, SH265 Owner's Manual ESE ESS FRC FRF HR ID IT PT RO RU SL TR ZH IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction

More information

FX850V. 4 stroke air-cooled V-twin gasoline engine OWNER S MANUAL

FX850V. 4 stroke air-cooled V-twin gasoline engine OWNER S MANUAL FX850V 4 stroke air-cooled V-twin gasoline engine OWNER S MANUAL SAFETY AWARENESS Whenever you see the symbols shown below, heed their instructions! Always follow safe operating and maintenance practices.

More information

WARNING: Read these instructions before using the machine GENERATOR MODEL NO: IG3500F PART NO: OPERATION & MAINTENANCE INSTRUCTIONS

WARNING: Read these instructions before using the machine GENERATOR MODEL NO: IG3500F PART NO: OPERATION & MAINTENANCE INSTRUCTIONS WARNING: Read these instructions before using the machine GENERATOR MODEL NO: IG3500F PART NO: 8877100 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0217 INTRODUCTION Thank you for purchasing

More information

Engines Original Instructions Model: DG350

Engines Original Instructions Model: DG350 Engines Original Instructions Model: DG350 Henton and Chattell Ltd: London Road, Nottingham NG2 3HW. UK. CONTENTS SECTION 1 INTRODUCTION......3 SECTION 2 SAFETY MESSAGES...3 SECTION 3 SAFETY INFORMATION...3

More information

Operating & Maintenance Instructions

Operating & Maintenance Instructions Operating & Maintenance Instructions Model Series Covered in This Manual 133400 134400 Model Type Code Note: General Model Series numbers noted above include many specific numbers like the ones on your

More information

Honda WX10T OWNER S MANUAL

Honda WX10T OWNER S MANUAL Honda WX10T OWNER S MANUAL Original instructions MANUEL DE L UTILISATEUR Notice originale BEDIENUNGSANLEITUNG Originalbetriebsanleitung MANUAL DE EXPLICACIONES Manual original Thank you for purchasing

More information

Owner s Manual. GENERATOR EU3000i. o2009 Honda Motor Co., Ltd. -All Rights Reserved. See page 83 for Initial Use Instructions

Owner s Manual. GENERATOR EU3000i. o2009 Honda Motor Co., Ltd. -All Rights Reserved. See page 83 for Initial Use Instructions Owner s Manual GENERATOR EU3000i o2009 Honda Motor Co., Ltd. -All Rights Reserved See page 83 for Initial Use Instructions The engine exhaust from this product contains chemicals known to the State of

More information

Viper 212cc 4-Cycle Engine

Viper 212cc 4-Cycle Engine Operator's Manual Original Operating Instructions Viper 212cc 4-Cycle Engine Model #: 25145 Email for more information info@ardisam.com P/N: 26694 ECN: 11258 REV1: 10/10/16 2016 Ardisam, Inc. All Rights

More information

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. Single-Stage (200 Series)

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. Single-Stage (200 Series) Safe Operation Practices Set-Up Operation Service Troubleshooting Operator s Manual Snow Thrower Single-Stage (200 Series) Table of Contents Safe Operation Practices... 2 Assembly & Set-Up... 5 Controls

More information