Get Fiber Smart. Part 1 : Best Practices in Enterprise Fiber Connectivity. Part 3: Best Practices in Tier2 Enterprise Fiber Link Testing and
|
|
- Sharlene Dixon
- 6 years ago
- Views:
Transcription
1 Get Fiber Smart Part 1 : Best Practices in Enterprise Fiber Connectivity Part 1 : Best 2: Practices Fiber in Testing Enterprise Fiber Fundamentals, Connectivity Standards Part and Best 2: Fiber Practices Testing for Fundamentals, Tier1 Enterprise Standards and Best Practices for Tier1 Enterprise Part 3: Best Practices in Tier2 Enterprise Fiber Link Testing and Part 3: Best Practices in Tier2 Enterprise Fiber Link Testing and Troubleshooting Troubleshooting
2 Agenda Fundamentals and Standards Reference Methods and Launch Conditions The Measurements Conclusion and dwrap-up
3 FUNDAMENTALS AND STANDARDS
4 What is Tier 1 Fiber Certification? Tier 1 Fiber Certification: Measure Length Measure Loss Check Polarity Ensure Loss does not exceed a limit Document results
5 A Consistency Challenge Tech A Tester A Tech B Tester A Tech A Tester B Tech B Tester B If different results different best practices
6 A Consistency Challenge Tech A Tester A Tech B Tester A If different results different tester specifications Tech A Tester B Tech B Tester B
7 Three Things That Impact Result Accuracy and Consistency 1. Fiber end-face condition Covered in Part 1 of this Webinar series 2. Reference method selected matches physical configuration and was properly performed 3. Multimode Transmitter Launch Condition The dreaded Encircled Flux!
8 A Brief Note on Standards The wonderful thing about standards is there are so many to choose from!
9 Channels and Links Applies to Fiber as Well Duplex Fiber Patch Cord Fiber Pair Additional connections possible Duplex Fiber Patch Cord Equipment Optical Patch Panel Optical Patch Panel Equipment Link Channel
10 db vs. dbm dbm = an ABSOLUTE measurement of power (1mW = 0dBm) db = a RELATIVE measurement Loss is a Reference Measurement (not an Absolute Measurement) First step in an accurate Loss Measurement is performing a reference! Purpose of a reference is to zero out any test t cables and connectors 1mW=0dBm Tx 2 db 5 db.5 db dBm Rx Loss = 7.5 db
11 REFERENCE METHODS AND LAUNCH CONDITIONS
12 Setting Reference Three options: 1 Fiber Reference Connect the OLTS together w/reference jumper reference power meter (set to 0dB) Light Source Test Jumper Power Meter Disconnect the fiber at the power meter. Connect a test jumper to the power meter. Add couplers (channel testing) or connect to bulkhead (link testing) and connect to fiber system under test Light Source Coupler/Bulkhead Test Jumper Coupler/Bulkhead Fiber System under Test Test Jumper OLTS = Optical Loss Test Set. Typically has Light Source and Power Meter at both ends. Simplex shown for clarity. Power Meter
13 Setting Reference Three options: 2 Fiber Reference Connect the OLTS together using two test jumpers and a coupler reference power meter (set to 0dB) Light Source Test Jumpers Coupler Test Jumpers Power Meter Disconnect the fibers at the coupler and connect the system to be tested (link testing). Need to add one coupler for channel testing Light Source Coupler/Bulkhead Coupler/Bulkhead Fiber System under Test Test Jumpers Test Jumpers Power Meter
14 Setting Reference Three options: 3 Fiber Reference Connect the OLTS together with two test jumpers, two couplers AND a third test t jumper reference power meter (set to 0dB) Light Source Couplers Test Jumpers Test Jumper Couplers Test Jumpers Power Meter Disconnect the fibers at the couplers, remove the third test jumper and connect system to be tested. Leave couplers in for channel testing, remove for link testing. Light Source Coupler/Bulkhead Coupler/Bulkhead Power Meter Fiber System under Test Test Jumpers Test Jumpers
15 Summary of Reference Methods Difference is the number of bulkhead (coupler) connections referenced out of the loss measurement. Use the method recommended by your local standards OR by your vendor! One Fiber Two Fiber Three Fiber Light Source Power Meter Fiber System under Test Test Jumpers Test Jumpers Always check your reference! Connect test jumpers together and measure loss Ensure no gainers Save result for proof of good reference
16 Multimode Launch Conditions Different multimode light sources = different modal power distributions (commonly referred to as launch conditions) Launch conditions directly impact link loss measurements accuracy LED overfills a multimode fiber tending to overstate loss Laser underfills a multimode fiber tending to understate loss Lower modes Cladding Higher modes Lower modes Cladding Overfilled source (LED) Core Cladding Underfilled source (Laser) Core Cladding
17 Encircled Flux (EF) Ratio between the transmitted power at a given radius of the fiber core and the total injected power Defined in IEC standard to characterize the launch conditions of MMF test sources Replaces older launch condition requires such as Coupled Power Ratio (CPR) Can be achieved by using a universal or matched modal controller Encircled flux 1 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0, radius (µm)
18 THE MEASUREMENTS
19 Measuring Length
20 Loss Limits Acceptable loss is based on several factors: Number of connections Number of splices Loss per Km (at specific wavelengths) Regional or vendor requirements Example allowable losses (TIA) Loss per connection = 0.75 db Loss per splice= 0.3dB Loss per Km (slope) 850nm = 3.5 db 1300nm = 1.5 db 1310 nm = 1.0 db 1550 nm = 1.0 db For Tier 1 Certification the user must tell the OLTS how many connectors and splices are in the fiber system under test
21 Tier 1 Fiber Certification Example One Fiber Reference 2 connections (default for one fiber reference) No splices 300 meters of MMF Test Limit at 850nm: 0.75 db per connector 1.5dB 300 meters (3.5 db per km) 1.05dB Total 2.55 db Test Limit at 1300nm: 0.75 db per connector 1.5dB 300 meters (1.5 db per km) 0.45dB Total 1.95dB Limit is based on settings Loss is measured Margin in calculated
22 Will My Application Actually Work? In this context, application is the protocol that will ride on the fiber. Typically Ethernet or Fiber Channel What is the connection between the limit on the previous slide and what tthe application requires? Very little Cable Type 1GbE 10GbE 40 /100GbE Loss (db) Length (m) Loss (db) Length (m) Loss (db) Length (m) OM OM Loss and Length Limits at 850nm
23 Compliant Networks Most Enterprise Optical Loss Test Sets will report Compliant Networks based on loss measurement Caution! Can PASS generic limit, it but have too much loss for specific application If the Application to be carried on the fiber is known, use Application (Network) limit
24 CONCLUSIONS AND WRAP UP
25 Ensure Your Results Are Accurate and Consistent 1. Treat your test reference jumpers AND the fiber under test with respect inspect and clean ALL fibers ALL the time Inspect Before You Connect SM IEC Certification 2. Understand dreference methods and their impact on limit, loss, and margin Reference method chosen in tester setup is correct and matches actual physical setup Check the reference often 3. Understand your multimode launch condition and have a plan to move to Encircled Flux Standard modal power distribution = consistent loss results between testers
26 Thank you for your attendance and attention! JDSU Eric M Farst Sales Engineer EAST Eric.Farst@JDSU.com
Variation of PIE-D in Multimode Fibre
Variation of PIE-D in Multimode Fibre Due to polarization, mechanical stress and connector offset Julia Shaw David Cunningham Simon Meadowcroft Fibre Optics Product Division Variation of PIE-D in Multimode
More informationFiber Optic, Breakout cable, tight buffered, 900 microns
Fiber Optic, Breakout cable, tight buffered, 900 microns Features and benefits Fiber-count 2-144 fibers 900 microns buffered design for easy termination Tight buffered construction Plenum (OFNP / FT6),
More informationSFP Fiber Optic Transceivers
arris.com SFP Fiber Optic Transceivers TTD4540/TTD4580 xx PI 10.3125 Gbps SFP+ DWDM Optical Transceiver Module FEATURES Provides long haul 10G Ethernet optical transmission up to 80 km Supports ARRIS Remote
More information50µm µlinx Avionics Cable
Summary of Results Supplemental Information for Qualified OFS Customer Use 50µm µlinx Avionics Cable p/n C26490 µlinx Optical Fiber Cable is a new reduced diameter product with an outer diameter of 0.8mm,
More informationOutside Plant All Dielectric
Berk-Tek s Outside Plant Loose Tube ber optic cables are designed for installation in harsh enviroments such as direct burial, aerial lashing, conduit and pathways that are subjected to wide temperature
More information10GBASE-LRM over 300m of FDDI-grade Fiber
GBASE-LRM over m of FDDI-grade Fiber Experimental & Simulation Results Jonathan King Sudeep Bhoja Ottawa Sept. 4 Big Bear Networks, Inc. Outline System Simulations Description of Model Results (CL & OSL)
More informationMPO MicroCable Trunk Assembly
Product updated on June 04, 2018 Trunk Assembly Trunks facilitate rapid deployment of high density backbone cabling in data centers or other high fiber density environments reducing network installation
More informationS Ingle Mode Fiber Patch Cord and Pigtail (SC/APC, LC/APC)
S Ingle Mode Fiber Patch Cord and Pigtail (SC/APC, LC/APC) 1. General : 1.1 This specification covers the requirements of the standard patch cord and pigtail to be supplied to TOT Public Company Limited
More information40G QSFP+ (MPO) to 4x10G SFP+ (8xLC) Assembly
Product updated on September 19, 2018 40G QSFP+ (MPO) to 4x10G SFP+ (8xLC) Assembly 40G parallel optics transceivers (40GBASE-SR4) can support 4x10G modes this feature allow new parallel optics active
More informationFiber Cables & Hardware
Fiber Cables & Hardware Quiktron has been the premier manufacturer of high performance fiber optic cables since 1994. Whether you are looking for standard or custom fiber cables, Quiktron can provide the
More informationLX2 High Density LGX 4U Patch Panel
LX2 High Density LGX 4U Patch Panel An innovative 4U, 19 and 23 rack mountable patch panel, designed for use in high density applications. It offers management of up to 288 fibres using MTP optical cassettes
More informationfiber optic cable Outdoor Cables
fiber optic cable Outdoor Outdoor Cables CST Armored cables for direct-buried applications Product specifications Outdoor Cables OC 1 CST & FRP Armor Applications Ideal for installation where direct-burial
More informationSW1 Swivel 1U Patch Panel
SW1 Swivel 1U Patch Panel An innovative 1U, 19 and 23 rack mountable swivel patch panel, designed to manage up to 48 fibres. It is compatible with LC, SC and FC adaptor types. This panel can swivel up
More informationMIC Unitized Plenum Cables, Fibers
MIC Unitized Plenum Cables, 36-144 s Features and Benefits Six- or 12-fiber jacketed subunits Quick and easy identification 900 µm TBII Buffered s Easy, consistent stripping All-dielectric cable construction
More informationLX2 High Density LGX 4U Patch Panel
LX2 High Density LGX 4U Patch Panel An innovative 4U, 19 and 23 rack mountable patch panel, designed for use in high density applications. It offers management of up to 288 fibres using MTP optical cassettes
More informationMTP Loose Tube Trunk Assemblies. Features. Applications.
Loose Tube Trunk Assemblies Up to 144 fibre loose tube optical cable assemblies designed and manufactured for high density applications that require interface. They are available in singlemode (G.652.D,
More informationMining and Petrochemical Tray-Rated Fiber Optic Cables
Features and Benefits Loose tube construction Stable and highly reliable transmission parameters Waterblocking technology Allows efficient and craft-friendly cable preparation Extra tough double jackets
More informationSW1 Swivel 3U Patch Panel
SW1 Swivel 3U Patch Panel An innovative 3U, 19 and 23 rack mountable swivel patch panel, designed to manage up to 144 fibres. It is compatible with LC, SC and FC adaptor types. This panel can swivel up
More informationMicro Fibre Indoor Cable Multi-core (Up to 96 Fibres) Applications. Features
Micro Fibre Indoor Cable Multi-core (Up to 96 Fibres) 2 to 96 Micro fibre indoor cable, 12 fibre stranded sub units, 250µm coloured fibre around an fibre reinforced plastic (FRP) central non-metallic strength
More informationMIC Plenum Cables, 2-24 Fibers
Features and Benefits 900 µm Buffered Fibers Easy, consistent stripping All-dielectric cable construction Requires no grounding or bonding Flame-retardant jacket Rugged and durable Standards Listings National
More informationCopyright 2004 Alcatel. All rights reserved.
Alcatel assumes no responsibility for the accuracy of the information presented, which is subject to change without notice. Alcatel, the Alcatel logo, MainStreet, and Newbridge are registered trademarks
More informationLC Cable Assemblies. Fiber Optic Products Catalog. Product Facts. LC Cable Assembly. Hybrid LC-SC Cable Assembly
LC Cable Assemblies Product Facts For high performance applications/high density 125 µm Ceramic Ferrule Technology Small size 1/2 size of standard SC and FC products Singlemode and multimode Tuned singlemode
More informationConstruction 2-24 tightly buffered fibres 900 m 50 m. colour code 1 Red 13 Yellow w/mark every 70 mm 2 Green 14 White w/mark every 70 mm 3 Blue 15 Gre
Universal indoor/outdoor distribution or mini breakout cable with ES9 tight buffer, 2 24 fibres and black FireBur sheath, VDE: U-V(ZN)H Application and Installation This distribution or mini-break-out
More informationVersiVision - High Definition Fiber Optic Video
Product Features Supports: - High Definition Composite Video Interface - Analog High Definition - High Definition Transport Video Interface 8-Bit Uncompressed Video Transmission Digitally Encoded NTSC,
More informationLaser Optimized Multimode
Solution Laser Optimized Multimode 1 Fiber optic LIU/489 FIU 2 Racks and cabinets 3 Equipment room: -600 G2 modular shelf and panel shelf -1000 G2 modular shelf and panel shelf 4 Telecom closet: -600 G2
More informationSystem configurator and order-information guide Oct Top-of-Rack Ethernet Switch - PSWITCH 2048T S26361-F3986-L405
5 Top-of-Rack Ethernet Switch - PSWITCH 2048T Oct. 2018 S26361-K1633-V100 PSWITCH 2048T 48x 10GBASE-T(RJ45) Port 6x QSFP+ Port No QSFP+ modules incl. incl. 2x PSU installed(redundant) incl. Rack Mount
More informationConstruction 2-24 tightly buffered fibres 900 m 50 m. colour code 1 Red 13 Yellow w/mark every 70 mm 2 Green 14 White w/mark every 70 mm 3 Blue 15 Gre
Universal indoor/outdoor distribution or mini breakout cable with ES9 tight buffer, 2 24 fibres and black FireBur sheath, VDE: U-V(ZN)H Application and Installation This distribution or mini-break-out
More informationWeatherproof Tubular Slip Ring Assembly
Weatherproof Tubular Slip Ring Assembly Model B8-4.3W 8 circuit weatherproof slip ring Compact design Mounts on shafts up to 4.3 [109.2 mm] in diameter Permanently lubricated bearings Rugged stainless
More informationMini Breakout Distribution Cable Multi-core ( Fibres)
Mini Breakout Distribution Cable Multi-core (12-144 Fibres) 12 to 144 fibre mini breakout multi-core distribution cable, consists of 4 to 8 individually coloured, 12 fibre stranded sub units around an
More informationConstruction 2-24 tightly buffered fibres 900 m 50 m. colour code 1 Red 13 Yellow w/mark every 70 mm 2 Green 14 White w/mark every 70 mm 3 Blue 15 Gre
Universal indoor/outdoor distribution or mini breakout cable with ES9 tight buffer, 2 24 fibres and black FireBur sheath, VDE: U-V(ZN)H Application and Installation This distribution or mini-break-out
More informationApplication Specification. Optical Fiber. Aramid Yarns. 2mm Subunit Jacket. Strength Rods. Outer Jacket
Application Specification 402-1012 February 28, 2017 Rev B Fiber Optic Breakout Cables Optical Fiber Aramid Yarns 2mm Subunit Jacket Strength Rods 2 Fiber Cable Outer Jacket 12 Fiber Cable Description:
More informationInterconnect Cable Simplex and Duplex
10.3 Interconnect Cable Simplex and Duplex Tight Buffer & Plenum Rated Patch panels Workstation equipment connections Horizontal distribution in open office environments Interconnect Cables are designed
More informationVolition. Fiber Optic Cable. 3Innovation
Volition Fiber Optic Cable Tough enough to take it. Easy to handle. Tough enough to take it. Easy to handle. The Volition Network Solution from 3M includes horizontal and backbone cable with 62.5/125 µm
More informationOptical Fibre Fibre Cables
Optical Fibre Fibre Cables Table of content Nexans 3 Nexans UK 4 Symbols 5 Fibre Cables 6 Optical cable speci cations 7 LANmark-OF Tight Buffer Indoor 10 LANmark-OF Tight Buffer Universal 13 LANmark-OF
More informationF485 Communications Converter
GE Grid Solutions F485 Communications Converter Instruction Manual F485 Communications Converter Manual P/N: 1601-0073-A5 GE publication code: GEK-119569A LISTED *1601-0073-A5* Copyright 2017 GE Multilin
More informationUSB3.0 for Active Optical Cable
USB3.0 for Active Optical Cable 1. Description 1. Basics: USB3.0 Active Optical Cable (AOC) speed up to 5 Gbps 2. Dimension of USB3.0 Type A male plug conforming requirements (Size: 56.1 x 8 x 16 mm).
More informationSPEC No.: ZP REVISION: 1.1 ZP ELECTRON CO.,INC. Designer. Division. Approver
TECHNICAL SPECIFICATION FOR Optical Fiber Overhead Ground Wire (OPGW) Designer Approver SPEC No.: ZP10-15389 REVISION: 1.1 Technical Supporter ZP Int ternational Division Chief Technical Engineer ZP Int
More informationFL2000 Termination/Splice Panels User Manual
FL2000 Termination/Splice Panels User Manual Content Page INTRODUCTION... 1 Revision History... 1 List of Changes... 1 Trademark Information... 2 Related Publications... 2 Admonishments... 2 General Safety
More informationHigh-Dynamic-Range Power Sensors Models 2101 & 2103
USER S GUIDE High-Dynamic-Range Power Sensors Models 2101 & 2103 2584 Junction Ave. San Jose, CA 95134-1902 USA phone: (408) 919 1500 e-mail: contact@newfocus.com www.newfocus.com Warranty New Focus, Inc.
More informationezprep Gel-Free Loose Tube Gel-Free Loose Tube Cable (2.5mm)
...... ezprep Gel-Free Loose Tube Gel-Free Loose Tube Cable (2.5mm) Optical Fibers Water Blocking Binders... Ripcord Jacket (polyethylene) Draka Optical Cable... Central Strength Member Flexible Buffer
More informationPhysical Layer Switch
Technology White Paper Physical Layer Switch Simultaneous Processing and Recording of High-speed Sensor Data Introduction The Sensor Application Environment Surveillance and intelligence gathering applications
More informationFC/APC Patchcord FC/APC. Insertion Loss(Reference plug) Insertion Loss (Random mated) Return Loss
FC/APC Patchcord FC/APC patchcord are mainly used in telecom network, especially in CATV, Local Area Networks (LAN) or FTTX networks. The requirement of insertion loss and return loss requirement was maintained
More informationCONNECTING POINT COMPUTER CONTRACT PRICING SHEET EXPIRES: OCTOBER 31, 2018
Description Unit Cost Number of Runs or Items CATEGORY 5 ENHANCED UNIT RUNS INSTALLATION Category 5E UTP 4 Pair (Plenum or Non Plenum) Unit Run Installation per Foot 0.30 X = Dual Category 5E (Plenum or
More informationENTERPRISE FIBER OPTIC CABLE. Interconnect Indoor Indoor/Outdoor Outdoor ADSS MicroCore
ENTERPRISE FIBER OPTIC CABLE Interconnect Indoor Indoor/Outdoor Outdoor ADSS MicroCore Founded in 1984, AFL is a global leader providing fiber optic products, equipment, and engineering services to the
More informationAvionics Optical Cables
Your Optical Fiber Solutions Partner Avionics Optical Cables for Commercial and Defense Aircraft FlightLink Cables FlightGuide Cables Avioptics Cable www.specialtyphotonics.com OFS Your Optical Fiber Solutions
More informationSYSTIMAX 360 ipatch G2 High Density Sliding Fiber Shelf Instructions
Instruction Sheet 860445121 Issue 2, December 2012 SYSTIMAX Solutions SYSTIMAX 360 ipatch G2 High Density Sliding Fiber Shelf Instructions General The SYSTIMAX 360 ipatch G2 High Density Sliding Fiber
More informationFeasibility Study of 4x10G CWDM - Potential Evolution of Technology - IEEE 802.3ba Interim Meeting Seoul, September 16-19, 19, 2008
Feasibility Study of 4x10G CWDM - Potential Evolution of Technology - IEEE 802.3ba Interim Meeting Seoul, September 16-19, 19, 2008 Eddie Tsumura (ExceLight Communications, Inc.) Kengo Matsumoto (Sumitomo
More informationTools. Features. KIT Installer tool
KIT Installer tool Features Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and FTTH installations: Inspection and cleaning of
More informationKeeping up with Industry 4.0. By Frederik Langenhoven
Keeping up with Industry 4.0 By Frederik Langenhoven SAFA Symposium 2018 - Emperors Palace, Kempton Park 24 May 2018 Agenda 1. Introduction 2. Process control architectures NAMUR Open Architecture (NOA)
More informationENTERPRISE FIBER OPTIC CABLE. Interconnect Indoor Indoor/Outdoor Outdoor ADSS MicroCore
ENTERPRISE FIBER OPTIC CABLE Interconnect Indoor Indoor/Outdoor Outdoor ADSS MicroCore Founded in 1984, AFL is a global leader providing fiber optic products, equipment, and engineering services to the
More informationDNV-GL HH CE RoHS-II conform
Armour: Extremely bending- and torsion-stable aramid braid Armour: Extremely bending- and torsion-stable aramid wrapping Outer jacket: Pressure extruded PUR mixture Fibre: FOC-fibre made out of glass Subcable
More informationUSB3.0 For Active Optical Cable SPECIFICATIONS
USB3.0 For Active Optical Cable SPECIFICATIONS PLUG, STD A USB 3.0 PLUG, STD A USB 3.0 MODEL COMOSS PART NUMBER USB3AOC-A/1-A/1-(X)M-XXX USB3AOC-A/1-AF/1-(X)M-XXX Custom PART NUMBER X PRELIMINARY Ver:
More informationExpressLT Dry Dry Loose Tube Cable (2.5 mm)
MANUFACTURED IN A versatile, multi-purpose fiber cable designed for ease of use and Buffer Tube Mid-Span Storage applications Overview Prysmian s popular ExpressLT cable combines buffer tubes with enhanced
More informationBasic design adapted to Telcordia GR409-CORE / TIA/EIA 568B.3 / ICEA-S
ADDISON Flame Retardant Tight Buffered Distribution Optic cables MTA-B-C-D-Y Tight Buffer Coating Glass Yarn Ripcord(optional) PVC Outer Sheath APPLICATION This cables are used for interconnection of distribution
More informationTender for procurement of Passive Components of LAN & Wi-Fi and their installation. Corrigenda. Annexure/Clause For Read
Tender for procurement of Passive Components of LAN & Wi-Fi and their installation Corrigenda Sl. No. Annexure/Clause For Read Item Specifications Item Specifications 1. Annexure-I, Point No. 1.3 24 Port
More informationDatasheet Outside Plant Cable
Outside Plant Cable Direct Buried Cable Direct buried cable can be buried directly into the ground in a trench or using a vibratory plow. Except for with great water-blocking and moisture-proof performance,
More informationVolition Fiber Optic Cable
Volition Fiber Optic Cable The Volition Network Solution from 3M includes horizontal and backbone cable with 62.5/125 µm and 50/125 µm multimode fiber, and 9/125 µm single-mode fiber. The horizontal cable
More informationField-testing procedure of
Field-testing procedure of LANmark-7A Technical Paper Nexans Cabling Solutions January 2012 Revision 1.45 Table of Contents 1 Introduction 3 2 How to proceed? 4 2.1 Introduction 4 2.2 Permanent link testing
More informationezspan ADSS Short Span All-Dielectric Self-Support Loose Tube Cable
...... ezspan ADSS Short Span All-Dielectric Self-Support Loose Tube Cable Water Blocking Binders... Ripcord Optical Fibers...... Flexible Buffer Tube Jacket (polyethylene) (3.0 mm) Aramid Strength Yarns......
More informationUSB3.0 For Active Optical Cable SPECIFICATIONS
USB3.0 For Active Optical Cable SPECIFICATIONS MODEL Comoss PART NUMBER Custom PART NUMBER PRELIMINARY Ver.. 1.0 OFFICIAL Release Date: 2015-01-26 CUSTOMER BY PREPARED BY APPROVAL CHECK BY DESIGN BY Victor
More informationIndoor/Outdoor Cables Single-Armored, Plenum, Tight Buffered Distribution Indoor/Outdoor Cable
Indoor/Outdoor Cables Single-Armored, Plenum, Tight Buffered Distribution Indoor/Outdoor Cable Single-Armored Tight Buffered Tight buffered fibers are positioned in a flexible metal tube, which is filled
More informationINTECH Micro 2300-RTD6
INTECH Micro 2300-RTD6 6 Channel RTD Input Station Overview. The Intech Micro 2300 Series is a system of modular I/O Remote Stations, that add an even lower cost option to Intech s already extensive intelligent
More informationSYSTIMAX 360 ipatch InstaPATCH Fiber Shelf Instructions
Issue 6, June 2014 SYSTIMAX 360 ipatch InstaPATCH Fiber Shelf Instructions General The SYSTIMAX 360 ipatch InstaPATCH fiber shelf is a SYSTIMAX approved product and is available in a sliding configuration
More informationPanView iq (PViQ) Fiber Tray
PVQ-FMT PanView iq (PViQ) Fiber Tray Part Number: PVQ-FMT Contents: 1 - FIBER TRAY (HOUSING & DRAWER) 6 - #12-24 x 1/2" SCREWS 6 - M6 x 1.0 x 16 SCREWS 2 - STRAIN RELIEF BRACKETS 2 - #10-32 BLACK HEX NUTS
More informationSilvertel. 1. Features. 2. Description. IEEE802.3at compliant. Maximum 30 Watt Output Power. High efficiency DC/DC converter
Silvertel V.0 May 2009. Features Pb IEEE802.3at compliant Maximum 30 Watt Output Power High efficiency DC/DC converter Wide adjustable output voltage range 500Vdc isolation (input to output) Input voltage
More informationViking Series 10/100Base-TX/FX, Auto MDI/MDIx, Autonegotiable MIL-DTL-38999, Unmanaged Ethernet Switch
Viking Series 10/100Base-TX/FX, Auto MDI/MDIx, Autonegotiable MIL-DTL-38999, Unmanaged Ethernet Switch 6 Port (4+2), Flange Mounted FEATURES 4x10/100Base-TX nonblocking wire speed copper Ethernet ports
More informationezspan ADSS All-dielectric self-supporting loose tube cable
All-dielectric self-supporting loose tube cable MANUFACTURED IN Aramid Strength Yarns Inner Jacket Polyethylene (optional) Central Strength Member Water Blocking Material Gel-Filled Buffer Tube Containing
More informationP R O D U C T C AT A L O G T ALOG
2 0 0 2 2002 PRODUCT CATALOG Need More Information? Visit our Web site at Instruction Sheets Cut Sheets White Papers Data Sheets Product/Part Number Searches AMP NETCONNECT Sales Engineer Contacts Authorized
More informationDSL-240 MkIII Single Pass Dust Monitor Measures mg/m 3 using DDP
Ideal for monitoring dust levels in the exhaust gas of industrial combustion or air filtration processes. Innovative Dynamic Detection Principle (DDP) measurement technique Immune to gradual reductions
More informationProduct Bulletin. Be Certain with Belden. Belden DataTwist 1200 Cables
Product Bulletin PB 294 Belden DataTwist 1200 Cables DataTwist 1200 UTP Cables are part of the industry s most powerful Category 5e networking solution: Belden IBDN System 1200. DataTwist 1200 Cables exceed
More informationPlug & Play AnyLAN Systems
features and benefits Factory-terminated cables Watertight components with compact, rugged design Multi-fiber quick connect Factory tested Modular SPECIFICATION SHEET LAN-731-EN PAGE 1 Install with no
More informationIntroduction to Fiber Cable Assemblies FiberDeep and Cable Assemblies
Introduction to Fiber Cable Assemblies FiberDeep and Cable Assemblies Combining 40+ years of experience from its founding members, Clearfield designs and manufactures fiber optic cable assemblies for virtually
More informationUser s Guide Power / Wave Measurement Heads OMH-6780B OMH-6790B
User s Guide Power / Wave Measurement Heads OMH-6780B OMH-6790B ILX Lightwave Corporation 31950 Frontage Road Bozeman, MT, U.S.A. 59715 U.S. & Canada: 1-800-459-9459 International Inquiries: 406-556-2481
More informationSPECIALTY AND HARSH ENVIRONMENT FIBER OPTIC CABLE. Downhole Subsea Transit Mining Military
SPECIALTY AND HARSH ENVIRONMENT FIBER OPTIC CABLE Downhole Subsea Transit Mining Military Founded in 1984, AFL is an international manufacturer providing end-to-end solutions to the energy, service provider,
More informationPanduit PreConfigured ZDF48-RA Industrial Distribution Frame (IDF) Installation Instructions
Panduit PreConfigured ZDF48-RA Industrial Distribution Frame (IDF) Installation Instructions Figure 1: Industrial Distribution Frame (IDF) Equipment Elevation V00028CA Rev01 Page 1 of 14 Table of Contents
More informationFAST-SC Connector. Any questions should be directed to AFL Telecommunications.
FAST-SC Connector This technical report demonstrates the reliability of the FAST-SC connector in meeting mechanical and environmental performance criteria. Testing was conducted on mm and sm varieties
More informationPanduit PreConfigured Industrial Distribution Frame (IDF) Installation Instructions Part Numbers ZDF and ZDF
Panduit PreConfigured Industrial Distribution Frame (IDF) Installation Instructions Part Numbers ZDF242430 and ZDF242430-6 Table of Contents Figure 1: Industrial Distribution Frame (IDF) Equipment Elevation
More informationCHAPTER 6 INTRODUCTION TO MOTORS AND GENERATORS
CHAPTER 6 INTRODUCTION TO MOTORS AND GENERATORS Objective Describe the necessary conditions for motor and generator operation. Calculate the force on a conductor carrying current in the presence of the
More informationFOS Fiber Optic Source
Service Information Sheet Introduction This Service Information provides the following service information for the FOS 850, FOS 300, and FOS 850/300 s (hereafter referred to as the FOS). Parts and warranty
More informationDSL-220 MkIII Single Pass Opacity Monitor Measures 0-100% Opacity
Ideal for monitoring opacity and smoke levels in the exhaust gas of industrial combustion or air filtration processes. In situ measurement directly in exhaust gas flow using the widely accepted light transmission
More informationCentrix System. Features and Benefits
Features and Benefits Supports 4,320 LC or 2,880 SC ports per cabinet Saves space through increased port density Available in front access, cabinet or open frame configuration Allows for back-to-back frame
More informationSAW Resonant PWS for Automotive and Industrial Applications
Passive Wireless Sensor-Tag Workshop Houston SAW Resonant PWS for Automotive and Industrial Applications Victor Kalinin 66 Heyford Park, Upper Heyford, Bicester, Oxon. OX25 5HD. UK Tel: +44 (0) 1869 238390
More informationTesting Energy Storage Systems: From EVs to Utility Grid
Testing Energy Storage Systems: From EVs to Utility Grid Jonathan P. Murray Business Development Manager 2008 Bloomy Controls. All Rights Reserved Agenda Energy storage system landscape Electric vehicle
More informationipatch Ready Upgrade Kit for SYSTIMAX 360 Fiber Shelves Instructions
Instruction Sheet 860463090 Issue 3, December 2012 SYSTIMAX Solutions ipatch Ready Upgrade Kit for SYSTIMAX 360 Fiber Shelves Instructions General These instructions describe how to install ipatch Ready
More informationWHITE PAPER. Optimizing High-Power PoE
WHITE PAPER Optimizing High-Power PoE Table of Contents Introduction... 3 Evolution of PoE Standards... 4 Additional Evaluation of High-Power PoE... 6 Testing that Replicates the Real World... 6 Jack Performance
More informationHigh Power Directional Coupler
DATA SHEET High power coupler at 500 W across a wideband from 698 to 2700 MHz Low RF Insertion Loss and excellent return loss performance Outdoor unit with a wide range of coupling values from 6 to 20
More informationFTTH simplex indoor cables with semi-tight tube
FTTH simplex indoor cables with semi-tight tube Design Cable design Strain relief Jacket material Jacket colour 1 semi-tight tube Aramide yarn LSFH white Properties Metal free indoor cable Strain relief
More informationUMA Fiber Optic Modular Adapter System Flexibility in a 2-Piece Adapter System
UMA Fiber Optic Modular Adapter System Flexibility in a 2-Piece Adapter System Universal Modular Adapter Family (2.5 mm Base) Features Two-piece design Single-mode applications SC, ST, and LC Clothespin
More informationOFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION
OFS 400A FIBER OPTIC INTERCONNECT 636-299-109-01 Instruction Sheet UNIT (FOIU) Comcode 846 586 212 INSTALLATION This instruction sheet covers the 400A1 (106266901) and 400A2 (106414170) Fiber Optic Interconnect
More informationReliability & Qualification Report for MEMS Based Variable Optical Attenuators
Reliability & Qualification Report for MEMS Based Variable Optical Attenuators P/N: MMVOA-1-1550-S-9/125-XX-0.25-1 Page 1 of 21 Revision History Rev Approval Date ECM/ECR Description of Change 00 10/18/2008
More informationInstallation Instructions for: Channel Thermocouple Amplifier
Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier WARNING: This installation is not fo r the electrically or mechanically challenged! Use this sensor with EXTREME caution! If you
More informationNLS4 SERIES LINEAR STAGE
NLS4 SERIES LINEAR STAGE The NLS4 have been designed for a variety of applications in research and other industrial areas requiring precision positioning such as in semiconductor processing, fiber optics
More informationTripTek Tire Car Kit Installation Procedure
TripTek Tire Car Kit Installation Procedure ANTENNA INSTALLATION 1. Assemble the antenna. Be sure to install the rubber washer and tighten the assembly using a wrench. 2. Magnetically mount the antenna
More informationRP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, inch, LMR-100
RP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, 0100 inch, LMR-100 RF Connectors Technical Data Sheet PE4771 Configuration SMA Male Reverse Polarity Connector MIL-STD-348
More informationOpticom Rack Mount Fiber Enclosures
Opticom Rack Mount Fiber Enclosures Part Numbers: FRME1U, FRME2U Panduit Corp. 2011 INSTALLATION INSTRUCTIONS FRME1U FRME2U Contents - (#) indicates FRME2U quantity 1 - ENCLOSURE 2 - MOUNTING BRACKETS
More informationCrimp & Cleave Termination Instructions
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 50 and 62.5µm GiHCS, 200µm HCS SC and SC-RJ Connectors For Use With: 50 and 62.5µm GiHCS 2.5mm Aramid Reinforced Optical
More informationMolex Premise Networks Systems Catalogue
Molex Premise Networks Systems Catalogue PowerCat 6 The Cat 6 Solution PowerCat 6 The Cat 6 Solution The PowerCat 6 Product Range Molex Premise Networks PowerCat 6 system product range is designed to comply
More informationInstructions for Use - Opt-X 1000i Enclosure
5R1UM-F03, 5R1UM-S03, 5R2UM-F06, 5R2UM-S06, 5R3UM-F09, 5R3UM-F12, 5R4UM-F12, 5R4UM-F15 Instructions for Use - Opt-X 1000i Enclosure 5R1UM-*03 5R2UM-*06 5R3UM-F** 5R4UM-F** Page 1 of 8 Leviton Network Solutions,
More informationMini-Span ADSS Cable
AFL Mini-Span All-Dielectric Self-Supporting (ADSS) cable is designed for outside plant aerial and duct applications in local and campus network loop architectures. From poleto-build to town-town installations,
More informationSinglemode Fused Coupler LGX Module (832 Series)
Features and Benefits Wideband and Dual Window Options Standard LGX Configurations High Stability & Reliability Rated for Outdoor Use Corning offers a full line of high performance coupler LGX modules.
More information