STOP. LP-50DEF-BRL Lever Hand Pump System Barrel Mounting. Owner s Manual DO NOT RETURN THIS PRODUCT TO THE STORE! SAVE THESE INSTRUCTIONS

Transcription

1 SAVE THESE INSTRUCTIONS LP-50DEF-BRL Lever Hand Pump System Barrel Mounting Owner s Manual 5252 East 36th Street North Wichita, KS USA FAX: STOP DO NOT RETURN THIS PRODUCT TO THE STORE! Please contact GPI before returning any product. If you are missing parts or experience problems with your installation, our Customer Support Department will be happy to assist you GPI Customer Support or TABLE OF CONTENTS General Information... 2 Safety Instructions... 2 Installation... 2 Operation... 3 Maintenance... 3 Specifications... 4 Illustrated Parts Drawing... 5 Service... 6 To the owner... Congratulations on receiving your GPI pump. We are pleased to provide you with a system designed to give you maximum reliability and efficiency. Your pump is designed, tested, and approved for use with Diesel Exhaust Fluid (DEF). Please take all due precautions when handling DEF. Your safety is important to us. Also, to assure the longest possible service life, it is important that you follow the Operation and Maintenance procedures outlined in this manual. We are proud to provide you with a quality product and dedicated support. Together with your conscientious use, we are sure that you will obtain years of safe, dependable service. Victor Lukic, President Great Plains Industries, Inc. BARREL NOT INCLUDED 11/13 Rev. A

2 GENERAL INFORMATION The purpose of this manual is to assist you in installing, operating and maintaining your GPI pump. It provides information which will help you achieve years of dependable performance and trouble-free operation. The system is approved for DEF (Diesel Exhaust Fluid) only. Do not use with gasoline, diesel, other flammable fluids, or micro-encapsulated fluids. Using fluids, other than those for which the pump was designed, could lead to serious personal injury and void the warranty. Before operating your pump, read this manual thoroughly and also read the printed information on the outside of the carton in which your LP-50DEF-BRL pump was packed. For assistance, contact your dealer or the GPI Customer Service Department. SAFETY INSTRUCTIONS The following safety alert symbols are used in this manual. INSTALLATION This pump is designed for use in a closed DEF barrel system. For proper installation, your pump requires a hose, nozzle and inlet hose (included with the system). In addition, a pump bracket kit designed for barrel mounting and either a RSV coupler or an EPV coupler (the couplers are specific to the DEF supplier barrel design) will be needed to maintain the closed DEF system. Kits for the pump bracket and both types of couplers are available from the factory and are listed as accessories on the Illustrated Parts List. Used pumps must be flushed and cleaned before installation as outlined in the Maintenance Section. Before Installing Pump Ensure that you have the following accessory items readily available: Assembled pump bracket kit and correct coupler to fit your barrel. Installing Pump The pump has a 2-inch NPS bung adapter at the inlet end. Remove the 2 NPT metal locknut and set aside. Attach inlet hose to pump inlet and secure with screw clamp. Tilt the pump slightly and insert the inlet hose through the hole in the pump bracket. Orient pump as shown. Slide the 2 NPT locknut over the inlet hose and onto the bung adapter and tighten securely against the underside of the pump bracket (Figure 1). DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. indicates a hazardous situation which, if not avoided, could result in death or serious injury. F I G U R E 1 CAUTION It is your responsibility to: CAUTION indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. Ensure that all equipment operators have access to adequate instructions concerning safe operating and maintenance procedures. Observe all safety precautions concerning safe handling of DEF. Avoid prolonged skin contact with DEF. Use protective goggles, gloves and aprons in case of splashing or spills. Change saturated clothing and wash skin promptly with soap and water. For your protection, thoroughly flush the pump before cleaning or repair. When you receive your pump, examine it for visible damage. If any items are damaged or missing, please contact your distributor. 2" NPT Locknut Inlet Hose Clamp Assembled Barrel Bracket Kit Place bracket with pump on top of barrel, position as shown (with bracket notches engaging rib of barrel rim) and secure to barrel with thumb screws, locking them in place with the double nuts. Install the required coupler into barrel outlet and attach inlet hose to coupler with screw clamp (Figure 2). 2 Rev. A

3 F I G U R E 2 EPV Coupler shown Clamp OPERATION Using fluids other than those for which the pump was designed could lead to serious personal injury and void the warranty. The pump system is approved for Diesel Exhaust Fluid only. Do not use with gasoline, diesel, other flammable fluids, or micro-encapsulated fluids. When handling fluids, always wear protective clothing such as goggles, gloves and respirators, as instructed by the fluid manufacturer. Install Hose and Nozzle Inlet hose If installing accessories such as meters or filters, do so before installing the hose and nozzle. Follow the manufacturer s instructions. F I G U R E 3 Clean any spills from the system exterior as they occur, following fluid manufacturer s instructions. Before Each Use 1. Keep pump exterior clean to help identify leaks. Before each use, inspect for leaks around seals or connections. 2. Make sure hoses are in good condition and connections are tight. 3. Make sure the work area is dry. MAINTENANCE Proper cleaning and maintenance is vital to prolong pump life and promote trouble-free operation. NOTE: Failure to follow recommended cleaning and storage procedures increases the chance of pump failure and may void the warranty. Remove Pump from Barrel Typical Installation CAUTION Make sure any hose and nozzle used are compatible with DEF. Slip one end of the hose onto the barbed pump outlet, install and tighten screw clamp. Slip the remaining end of the hose onto the barbed fitting on the nozzle, install and tighten screw clamp. Some fluid may spill from the pump during removal. Follow DEF label directions for cleanup and disposal. 1. Remove coupler and bracket/pump from barrel. 2. Place the nozzle into a receiving tank. 3. Open the nozzle to remove fluids from the system and actuate pump to empty any remaining fluid. 4. Clean external fluid from pump and components. 5. If the pump will not be used for more than 2 weeks, flush to prevent drying of fluids in the pump. Rev. A

4 Flush Pump When the pump will not be used for more than two weeks, it must be flushed to prevent internal drying of fluid. It is strongly recommended, for protection from personal injury, that a simple flush tank be created. Use a container with a tight fitting lid with a minimum volume of five gallons (19 litres). Cut holes in the lid of this container large enough for the inlet hose and coupler to fit through. Fill the container with distilled water. Secure the lid tightly on the top of the container during use. 1. Refer to the Remove Pump From Barrel paragraph and follow those instructions to remove and drain the pump. 2. Place the inlet hose with coupler and the nozzle through the hole in the lid of the flush tank. (Figure 4) F I G U R E 4 Clean Pump If fluid dries inside pump, the residue could damage the pump if it is actuated dry. The residue is water soluble and dissolves very quickly. 1. Soak the pump in a container of distilled water for approximately five minutes, ensuring all pump cavities are water filled, to dissolve the residue. 2. At the end of the soak, actuate the submerged pump to flush water through the inlet and outlet ports. 3. Remove pump and actuate to remove any remaining water. LP-50DEF-BRL SPECIFICATIONS Coupler hose (coupler in bucket) Applications Fluids: Operating Environment: Diesel Exhaust Fluid Outdoor, operating temperature Range of +40 F to +100 F (+5 C to +38 C) 4"- 5" air space to lift coupler clear of water 3. Open the nozzle and actuate the pump to circulate distilled water through the pump for 10 to 15 minutes. Close and open the nozzle several times to flush interior nozzle components. 4. Lift the inlet hose with coupler from the water and actuate the pump briefly until only air passes through the system. 5. Drain the hose and nozzle and close the nozzle. Wipe entire system with a clean damp cloth. To avoid fluid exposure, follow fluid manufacturer s instructions for the disposal of contaminated water. Pump Housing Performance Pump Rate: Lightweight, durable, molded plastic housing Convenient 2-inch NPS bung adapter for easy installation. Fits standard 2-inch bung. 500 ml (16.9 fluid ounces) per stroke Single action piston Self priming to at least 36 inches above fluid Mechanical Connections Outlet: 1-inch Hose Barb Weight Shipping: 8.25 lbs (3.7 kg) NOTE: Although the pump can be used with Water, Antifreeze, Diesel Fuel, Petroleum Based Products, Mild Detergents, Lubricants, Diesel Exhaust Fluid (DEF), urea solution / AUS 32 and most Agricultural Chemicals, the hose and nozzle combination received with this LP-50DEF-BRL system limits the system to being used with Diesel Exhaust Fluid (DEF) only. Do Not Use With Kerosene, Roundup Concentrate or Flammable Fluids. 4 Rev. A

5 ILLUSTRATED PARTS DRAWING 4 3 Kits / Accessories not included: DEF Barrel Bracket Kit RSV Coupler ¾" Barbed EPV Coupler ¾" Barbed Item No. Part No. Description No. Req'd Fitting, 90, 3/4" NPT X 3/4" Hose Barb Locknut, Rigid Conduit (2" NPT) Hose Clamp Kit Inlet Hose, 3/4" EPDM Tubing, EVA. 6 Ft LP-50DEF-BRL Assembly Nozzle, Def Ball Valve, 1" Hose BARB... 1 Rev. A

6 SERVICE For warranty consideration, parts or other service information, please contact your local distributor. If you need further assistance, contact the GPI Customer Service Department in Wichita, Kansas, during normal business hours. A toll-free number is provided for your convenience To obtain prompt, efficient service, always be prepared with the following information: The model number of your pump The manufacturing date code of your pump Parts descriptions and numbers Part information can be obtained from the Illustrated Parts Drawing. For warranty work, always be prepared with your original sales slip or other evidence of purchase date. Please contact GPI before returning any parts. It may be possible to diagnose the trouble and identify needed parts in a telephone call. GPI can also inform you of any special requirements you will need to follow for transportation and handling of fluid equipment. CAUTION Do not return the pump or parts without authority from the Customer Service Department. Due to strict government regulations, GPI cannot accept parts unless they have been drained and cleaned. 6 Rev. A

7

8 Limited Warranty Policy Great Plains Industries, Inc E. 36 th Street North, Wichita, KS USA , hereby provides a limited warranty against defects in material and workmanship on all products manufactured by Great Plains Industries, Inc. This product includes a 90 day warranty from date of purchase as evidenced by the original sales receipt. Manufacturer s sole obligation under the foregoing warranties will be limited to either, at Manufacturer s option, replacing or repairing defective Goods (subject to limitations hereinafter provided) or refunding the purchase price for such Goods theretofore paid by the Buyer, and Buyer s exclusive remedy for breach of any such warranties will be enforcement of such obligations of Manufacturer. The warranty shall extend to the purchaser of this product and to any person to whom such product is transferred during the warranty period. This warranty shall not apply if: A. the product has been altered or modified outside the warrantor s duly appointed representative; B. the product has been subjected to neglect, misuse, abuse or damage or has been installed or operated other than in accordance with the manufacturer s operating instructions. To make a claim against this warranty, contact the GPI Customer Service Department at or Or by mail at: Great Plains Industries, Inc E. 36 th St. North Wichita, KS, USA GPI will step you through a product troubleshooting process to determine appropriate corrective actions. GREAT PLAINS INDUSTRIES, INC., EXCLUDES LIABILITY UNDER THIS WARRANTY FOR DIRECT, INDIRECT, INCIDENTAL AND CONSEQUENTIAL DAMAGES INCURRED IN THE USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER. The company herewith expressly disclaims any warranty of merchantability or fitness for any particular purpose other than for which it was designed. This warranty gives you specific rights and you may also have other rights which vary from U.S. state to U.S. state. Note: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT Part 702 (governs the resale availability of the warranty terms) East 36th Street North Wichita, KS USA FAX: by GREAT PLAINS INDUSTRIES, INC., Wichita, KS Printed in U.S.A. 11/13 Rev. A