Pump System Technology. Owner's Manual SERIES LP PUMP. For series: LP50, LP200, LP450, LP650. Series LP50

Transcription

1 Pump System Technology Owner's Manual SERIES LP PUMP For series: LP50, LP200, LP450, LP650 Series LP50

2 Dear Fill-Rite Customer, Congratulations on your purchase of Fill-Rite s new Series LP pump. We at Fill-Rite have built our worldwide reputation by designing the finest and most reliable pumps available in today s market. Your new pump was designed with pride by some of the best and most experienced fluid control experts available. We use the most advanced technology possible to give you a pump with the superiority you deserve and the quality you ve come to expect from Fill-Rite products. Sincerely yours, GENERAL DESCRIPTION The Fill-Rite LP Lube Pump is a positive displacement, direct drive pump for lubrication fluids. The rugged design makes for a long life of trouble-free operation. SAFETY The motors used in Fill-Rite LP pumps are listed with: Underwriters Laboratories Inc., a nationally recognized independent organization for product testing to ensure public safety. MOTOR The Fill-Rite Team WARNING Canadian Standards Association, a Canadian organization for product testing to ensure public safety. Explosion Hazard Static charge could result in a fire or explosion. Do not use pump with low flash point fluids (100 F or less) or in Hazardous locations. WARNING Electrical Hazard Improper use or installation can cause serious bodily injury or death. Motor must be properly grounded. Electrical wiring must be done by a licensed electrician. SAFETY INSTRUCTIONS 1. To ensure safe and efficient operation, it is essential to read the entire manual before installing or operating this product. 2. This pump is not suited for use with fluids containing water. 3. The pump motor is equipped with thermal overload protection. If overheated, it will shut itself off without damage to the windings. Turn off the pump power if this occurs. As the motor cools, it may start without warning if power is on. 4. NOTE: Pump has a built-in check valve with pressure relief to prevent fluid thermal expansion from causing unsafe system pressures. DO NOT USE ADDITIONAL CHECK VALVES OR FOOT VALVES UNLESS THEY HAVE PROPER PRESSURE RELIEF VALVES (MAX. 30 PSI) BUILT INTO THEM. GENERAL TECHNICAL INFORMATION Inlet: 2" female NPT mounting on pump, 1" female NPT for suction pipe. 2" male threads on quick detach adapter with 1" female NPT for suction pipe. Outlet: ¾" NPT Built in check valve, bypass and pressure relief valves Motor: Thermal overload protection Permanent sealed ball bearing construction Series LP50 kit pumps are as 115 VAC or 12VDC 115/230 VAC on bulk and demand pumps Performance Maximum outlet pressure from psi ( bar) Maximum flow rate: up to 36 qpm (34 lpm) Maximum viscosity of fluid pumped: See page 7. Maximum fluid temperature: 150 F Minimum fluid temperature: See viscosity chart page 7. Minimum dry vacuum: 6 inches of mercury Fluid Compatibility The LP pump is compatible with the following fluids: Motor Oil, Gear Oil, Hydraulic Oil, Industrial Coolant, Antifreeze (not to exceed 50% water), ATF, Waste Oil. The LP pump is NOT compatible with the following fluids: Water, Acids, Brake Fluid, Windshield Washer Fluid If in doubt about compatibility of a specific fluid, contact supplier of fluid to check for any adverse reactions to the following wetted materials. Cast Iron Steel Stainless Steel Brass Flourocarbon Zinc Pltd. Stl. Aluminum 2

3 GENERAL INSTALLATION INSTRUCTIONS NOTE: Pump has a built-in check valve with pressure relief to prevent fluid thermal expansion from causing unsafe system pressures. DO NOT USE ADDITIONAL CHECK VALVES OR FOOT VALVES UNLESS THEY HAVE PROPER PRESSURE RELIEF VALVES (MAX. 30 PSI) BUILT INTO THEM. All tanks must be properly vented. Use oil resistant pipe sealant on all threaded joints. Drums must be properly secured to prevent tip over when full or empty. MOUNTING LP PUMP USING QUICK-DETACH BUNG ADAPTER Quick-Detach Bung Adapter 1" Suction Pipe Figure 1a Use sealant here Mounting the LP Pump using the Quick-Detach Adapter (See Figure 1a & 1b) 1. Screw length of suction pipe into the quick-detach adapter that extends 1" to 2" above bottom of tank. 2. Screw quick-detach adapter securely into tank bung. 3. Lubricate O-ring on pump inlet. 4. Position pump on adapter. Pump can be rotated in 90 increments. Tighten 2 screws to secure pump to adapter. Figure 1b Tighten screws Lubricate O-ring Mounting the LP Pump using the Motor Bracket (See Figure 2 & 3) CAUTION MOTOR MOUNTING BRACKET Mounting Bracket Always mount pump using motor bracket when mounting pump to a vehicle. 1. Using mounting plate as template, mark holes on mounting surface. 2. Use four 3/8" bolts with lock washers and nuts to attach bracket to mounting surface. Tighten securely. Mounting the LP Pump directly to a tank (See Figure 4) The Pump inlet flange has a 2" female NPT thread that can be mounted directly to a 2" male pipe thread on the tank. If only female threads are available on the tank, use a 2" schedule 40 pipe nipple to connect pump to the tank. 1. Screw correct length of 1" suction pipe into the pump inlet flange 1" port. Suction pipe should extend 2" to 3" above bottom of tank. 2. Thread pump directly onto the 2" tank nipple and tighten securely. Mounting Bracket Horizontal Mounted Wall Mounted Figure 2 Figure 3 DIRECT MOUNTING INSTALLATION Use sealant here 1" Suction Pipe 2" Schedule 40 nipple 2" Tank Bung Figure 4 3

4 INSTALLATION, DISCHARGE PLUMBING ON PUMP OUTLET LP50 Kit Pumps (50psi): Install hose and nozzle using oil resistant pipe sealant on threads. Tighten securely. If desired, install nozzle boot as shown. Tighten bolts securely. 1 2 # 1 Description Screw, on motor LP200 Series Bulk Pumps (200psi): Use hoses, pipes, fittings, and meters that can safely handle the rated pump pressure. A short length of flexible hose (5 FT. min.) is required at the pump outlet before connecting to rigid metal piping. For best performance, use the largest inside diameter pipe practical for long runs of pipe to minimize pressure drop and maximize flow rate. LP450 and LP650 On Demand Pumps ( psi): Use hoses, pipes, fittings, and meters that can safely handle the rated pump pressure. WARNING High Pressure Fluid Hazard Improper installation can cause serious injury or death. Use hose and pipe fitings rated for a min. of 800 psi A short length of flexible hose (5 FT. min.) is required at the pump outlet before connecting to rigid metal piping. For best performance, use the largest inside diameter pipe practical for long runs of pipe to minimize pressure drop and maximize flow rate. 2 Plastic Washer, found in literature bag Instructions for Removing the Motor Bracket Note: Bracket screws with supplied plastic washers must be re-installed in the motor to prevent dirt and moisture from damaging motor. 1) Remove motor bracket screws and bracket. 2) Slip plastic washer over motor bracket and re-install into motor. Tighten to 30 in*lbs. DO NOT OVERTIGHTEN SCREWS. ELECTRICAL INSTALLATION WARNING Electrical Hazard Improper use or installation can cause serious bodily injury or death. Shut off all power before connecting wires to motor Electrical wiring must be done by a licensed electrician. LP50 Series Kit Pumps, AC Power Factory wired for 115VAC. Power to the unit should be supplied from a dedicated circuit breaker. AC extension cords must be capable of safely carrying the rated motor current. Use heavy duty, 3-wire, grounded extension cords. Note that long extension cords must be larger gauge wire to safely handle the electrical load: -up to 25 feet, 14 AWG wire -up to 50 feet, 12 AWG wire -up to 100 feet, 10 AWG wire NOTE: Many building codes require Ground Fault Circuit Interrupt (GFCI) protection. 4 LP50 Series Kit Pumps, 12V DC Power Factory wired for 12VDC. Circuit must be protected with a 50 amp automotive fuse. Power cord must be capable of safely carrying the rated current. Long power cords must be larger gauge wire to safely handle the electrical load. -up to 8 feet, 8 AWG wire -up to 20 feet, 4 AWG wire

5 LP200 Series Bulk Pumps See page 11 for factory set voltage. A diagram on the motor label describes how the electrical connections are to be made. Power to the motor should be supplied from a dedicated circuit breaker sized to handle the motor load. Provisions must be made to break both legs of the 230VAC circuit. Conduit should be used to protect all permanent wiring installations. LP450 & LP650 Series On-Demand Pumps WARNING Spill hazard Entire tank could be emptied by the On-Demand pump if a leak occurs in the nozzle, meter, hose, or piping. Turn power switch off when not attended. Pump Fluid Outlet "On-Demand" switch junction box. Customer supplied power here. Use sealed cable connection that prevents water from entering junction box. See page 12 for factory set voltage. Instructions in the "On-Demand" switch junction box describes the electrical connections. The neutral wire must be wired to the #3 terminal in the "On- Demand" switch juction box for proper operation. Ground wire must be connected to the green wire inside the "On-Demand" switch junction box. Power to the motor should be supplied from a dedicated circuit breaker sized to handle the motor load. Provisions must be made to break both legs of the 230 VAC circuit. Conduit should be used to protect all permanent wiring installations. OPERATING INSTRUCTIONS Note: Do not operate pump dry (except at initial startup), damage to pump could occur. LP200 Series Bulk Pumps: Place customer supplied nozzle in container to be filled. Turn on motor. Fill container to desired level. Shut off and remove nozzle. Turn off motor. LP450 and LP650 Pumps with "On Demand" switch: Make sure user supplied discharge nozzle is closed. Turn pump motor switch on. Motor may turn on momentarily to build pressure in line if pump has not been used recently. If motor does not shut off after 30 seconds, turn off power and see "Trouble Shooting Guide" on page 6. Place nozzle in container to be filled. Open nozzle. Motor will automatically turn on. Fill container or vehicle reservoir to desired level. Shut off nozzle. Pump motor will automatically shut off after 6 seconds. Turn off pump motor switch when not attended. Purge the air from the pump: Purge Valve and Purge Valve Screw are assembled to the pump at the factory. Purge Connector and plastic tube are in a plastic bag shipped with the pump. 1) Thread the Purge Connector to the Purge Valve. 2) Push the purge tube into the Purge Connector. 3) Start pump. Using a flathead screw driver, turn the Purge Valve Screw counter clockwise. When tube starts to fill with oil, tighten screw back down. Unit is now primed. 4) Remove Purge Tube by pushing in the black plastic portion of the Purge Connector and pulling the tube out. 5) Wipe up any oil drips. Purge Connector can be left on the pump or removed. LP450H0035 Purge Connector (in bag) Flat head screw driver LP450H0038 Purge Valve Screw (on pump) LP450H0037 Purge Valve (on pump) LP50 Kit Pumps: Place nozzle in container to be filled. Turn on motor. Fill container to desired level. Shut off nozzle. Turn off motor and hang up nozzle. 5

6 TROUBLESHOOTING GUIDE Problem Possible Cause Solution Dirty Strainer screen Remove and clean strainer Suction line problem Check for leaks in suction line O-ring in tank adptor damaged or missing. Inspect and replace o-ring if needed. Pump outlet is blocked or valve is shutoff. Check pump outlet system for blockage. Air trapped in system. Vent air from system (On-demand models have air purge valve) Pump Won't Prime Fluid level below suction pipe. Refill tank or add longer suction pipe. Fluid viscosity exceeds pumps rated capability. Refer to page 7 for viscosity limits Exceeds lift capacity of pump Do not exceed 7 feet of lift for oil Gears are locked. Inspect gears for smooth rotation, remove any debris. Excessive gear wear Inspect gears, replace if worn. Bypass valve not seating Remove/inspect bypass valve, clean if necessary. Shaft key is sheared or missing. Open rotor cover and inspect shaft key. Dirty Strainer screen Remove and clean strainer Suction line problem Check for leaks in suction line Fluid viscosity exceeds pumps rated capability. Refer to page 7 for viscosity limits Outlet system pressure too high. Check outlet system for blockage. Low capacity (low Nozzle or meter has higher pressure flowrate) requirements than what pump is rated for. Replace meter or nozzle. Bypass valve not seating Remove/inspect bypass valve, clean if necessary. Excessive gear wear Inspect gears, replace if worn. Low voltage to motor Ensure power at motor is at proper voltage. Motor stalls when valve/nozzle is closed. Bypass valve is sticking. Remove and inspect bypass valve. Clean if necessary. Motor stalls when Fluid viscosity exceeds pumps rated capability. Refer to page 7 for viscosity limits pump first starts. Gears are locked. Inspect gears for smooth rotation, remove any debris. Fluid viscosity exceeds pumps rated capability. Refer to page 7 for viscosity limits Motor overheats Gears are not rotating smoothly. Inspect gears for smooth rotation, remove any debris. Incorrect voltage Ensure power at motor is at proper voltage. No power to motor Check circuit breakers and electrical connections. Motor will not turn on Switch failure Replace switch. Motor has tripped internal motor protection. Allow motor to cool for at least 30 minutes. Missing or damaged seal Inspect affected area for proper o-ring/gasket. Pumps leaks. Shaft seal damage. Inspect and replace shaft seal if needed. Incompatible fluid pumped. Check fluid compatibility in Owners Manual ON-DEMAND PUMPS ONLY On-demand motor Fluid viscosity exceeds pumps rated capability. Refer to page 7 for viscosity limits turns off before nozzle is closed. System exceeds rated values for pump. Change system pressure or replace pump. Motor runs for ~6 seconds after nozzle is closed Normal operation, no problem On-demand motor Pressure is too low due to air in system. Air in system must be purged. does not turn off Fluid is too light to build up enough pressure. Turn pump off manually. automatically Leak in system allowing pressure to drop. Inspect system line for leaks Check valve not seating properly. Inspect check valve for debris or damage. On-demand motor Periodic charging of system is normal. Shut off motor when not attended 6

7 Table 1: Viscosities Limits - (SSU) Model Name LP50P18Q115 LP50P36Q115 LP50P18Q12 LP200P18Q LP200P36Q LP450P10Q LP650P10Q Maximum Minimum (Start-up) (Start-up) 6,000 N/A 5,000 N/A 2,000 N/A 7,000 N/A 6,000 N/A 6, , Table 2: Viscosities of Common Fluids at Various Temperatures Temp Temp. ATF ISO 46 Deere 10W-30 15W Wt. SAE Wt. 50 Wt SAE 140 ( F) ( C) Mil SSU HyGard Gear Lube Gear Lube Gear Lube N/A N/A 7

8 MAINTENANCE Disconnect all power and relieve pressure by opening nozzle before servicing pump. To keep pump running at its best, periodically perform the following procedures. 1. Check strainer for dirt accumulation. To clean strainer, remove strainer cover (item 18 on page 8) and pull out screen (item 20 ). Clean gasket surface on strainer cover (item 18 ), pump (item C ) and gasket (item 19). Reinstall and tighten strainer cover firmly. 2. Check hose and nozzle for wear or damage. Worn and damaged hoses or nozzles are potential safety hazards and should be replaced. 3. If the rotor cover (item 15) is removed, note that the rotor cover can only be reassembled as shown in the exploded view on page 8. REPAIR To maintain safety, motors that need repair should be taken to an authorized repair shop. Pumps must be thoroughly flushed and drained before being taken in for service. BASIC LP PUMP PARTS LIST (Common to all models) A Pages 9-12 Motor - Model Specific 1 2 LP50H0157 Bypass Cap Assembly 1 3 LP50H0069 Bypass Cap O-Ring 1 B Pages 9-12 Bypass Spring - Model Specific 1 5 LP50G9976 Bypass Valve 1 C Pages 9-12 Pump Housing - Model Specific G8109 O-Ring -124 (Outlet Flange) 1 D Pages 9-12 Check Valve Assembly - Model Specific 1 9 LP50G9927 Outlet Flange 1 10 LP50H0066 Screw 5/16 x 7/8" SHCS (Outlet Fitt.) 2 11 LP50G9974 Lip Seal, Motor Shaft 1 E Pages 9-12 Gear Set - Model Specific 1 13 LP50G9990 Key Shaft 1 14 LP50G9972 O-Ring, Rotor Cover 1 15 LP50G9920 Rotor Cover 1 16 LP50H0219 Screw 5/16-18 x 3/4"SHCS 6 17 LP50G9973 Screw 3/8-16 x 1" SHCS F4370 Strainer Cap F4381 Gasket, Strainer Cap F2665 Stainer Screen F7744 Gasket, Lathe cut (-244) 1 22 LP50H0027 Tank Adapter Quick-Detach 1 23 LP50G9979 O-Ring -232 (Inlet Flange) 1 24 LP50G9924 Inlet Flange 1 25 LP50H0219 Screw 5/16-18 x 3/4"SHCS 2 8

9 MODEL LP50P18Q115 MAX FLOW = 18 qt/min (17 liter/min) MAX PRESSURE = 50 psi (3.4 bar) NOMINAL CURRENT DRAW = VAC LP KIT MODELS 1 702F3400 Elbow 3/4" NPT 1 2 Incl. w/motor Motor Mounting Bracket 1 3 LP50H0027 Quick-Detach Bung Adapter KTG7743 Suction Pipe 1" (Includes item 5-6) 1 5 VP1400F7687 Suction Pipe 1" PVC, Extension 2 6 VP1400F7686 Suction Pipe 1" PVC, Assembly 1 7 LP50G9987 Hose 3/4" ID X 8 feet long 1 8 6U075 3/4" Manual Nozzle 1 9 LP50H0090 Nozzle Cover F7751 Screw 5/16-18 x 1/2" (Nozzle Cover) 2 A LP50G9958 Motor 1/3 HP, 115VAC, 1700 rpm 1 B LP50G9977 Bypass Spring 1 C LP50G9922 Pump Housing 1 D LP50G9980 Check Valve Assembly 1 E LP50G9944 Gear Set 1 LP50G9967 Power Cord 36" long (not shown) 1 MODEL LP50P36Q115 MAX FLOW = 36 qt/min (34 liter/min) MAX PRESSURE = 50 psi (3.4 bar) NOMINAL CURRENT DRAW = VAC 1 702F3400 Elbow 3/4" NPT 1 2 Incl. w/motor Motor Mounting Bracket 1 3 LP50H0027 Quick-Detach Bung Adapter KTG7743 Suction Pipe 1" (Include items 5-6) 1 5 VP1400F7687 Suction Pipe 1" PVC, Extension 2 6 VP1400F7686 Suction Pipe 1" PVC, Assembly 1 7 LP50G9987 Hose 3/4" ID X 8 feet long 1 8 6U075 3/4" Manual Nozzle 1 9 LP50H0090 Nozzle Cover F7751 Screw 5/16-18 x 1/2" (Nozzle Cover) 2 A LP50G9959 Motor 1 HP, 115VAC, 3400 rpm 1 B LP50G9977 Bypass Spring 1 C LP50G9922 Pump Housing 1 D LP50G9980 Check Valve Assembly 1 E LP50G9944 Gear Set 1 LP50G9968 Power Cord 36" long (not shown) 1 9

10 MODEL LP50P18Q12 MAX FLOW = 18 qt/min (17liter/min) MAX PRESSURE = 50 psi (3.4 bar) NOMINAL CURRENT DRAW = 39 12VDC 1 702F3400 Elbow 3/4" NPT 1 2 Incl. w/motor Motor Mounting Bracket 1 3 LP50H0027 Quick-Detach Bung Adapter KTG7743 Suction Pipe 1" (Include items 5-6) 1 5 VP1400F7687 Suction Pipe 1" PVC, Extension 2 6 VP1400F7686 Suction Pipe 1" PVC, Assembly 1 7 LP50G9987 Hose 3/4" ID X 8 feet long 1 8 6U075 3/4" Manual Nozzle 1 9 LP50H0090 Nozzle Cover F7751 Screw 5/16-18 x 1/2" (Nozzle Cover) 2 A LP50G9957 Motor 1/2 HP, 12VDC, 1700 rpm 1 B LP50G9977 Bypass Spring 1 C LP50G9922 Pump Housing 1 D LP50G9980 Check Valve Assembly 1 E LP50G9944 Gear Set 1 10

11 MODEL LP200P18Q MAX FLOW = 18 qt/min (17 liter/min) MAX PRESSURE = 200 psi (13.8 bar) NOMINAL CURRENT DRAW = VAC NOMINAL CURRENT DRAW = 6 230VAC FACTORY WIRED FOR 115VAC LP BULK TRANSFER MODELS 1 Incl. w/motor Motor Mounting Bracket 1 2 LP50H0027 Quick-Detach Bung Adapter 1 A LP450G9960 Motor 1 HP, 115VAC, 1700 rpm 1 B LP200H0067 Bypass Spring 1 C LP50G9922 Pump Housing 1 D LP50G9980 Check Valve Assembly 1 E LP50G9944 Gear Set 1 MODEL LP200P36Q MAX FLOW = 36 qt/min (34 liter/min) MAX PRESSURE = 200 psi (13.8 bar) NOMINAL CURRENT DRAW = VAC NOMINAL CURRENT DRAW = VAC FACTORY WIRED FOR 230VAC NOTE: Not recommended for use with 115VAC power unless circuit is fitted with appropriate breaker and wire size to handle motor load. 1 Incl. w/motor Motor Mounting Bracket 1 2 LP50H0027 Quick-Detach Bung Adapter 1 A LP200G9962 Motor 2 HP, 115/230 VAC, 3400 rpm 1 B LP200H0067 Bypass Spring 1 C LP50G9922 Pump Housing 1 D LP50G9980 Check Valve Assembly 1 E LP50G9944 Gear Set 1 11

12 LP ON-DEMAND PUMP MODEL LP450P10Q MAX FLOW = 10 qt/min (9.5 liter/min) MAX PRESSURE = 450 psi (31 bar) NOMINAL CURRENT DRAW = 115VAC NOMINAL CURRENT DRAW = VAC PRESSURE SENSING ON/OFF SWITCH = Set at 400 psi FACTORY WIRED FOR 115VAC 1 Incl. w/motor Motor Mounting Bracket 1 2 LP50H0027 Quick-Detach Bung Adapter 1 A LP450G9960 Motor 1 HP, 115/230 VAC, 1700 rpm 1 B LP450H0068 Bypass Spring 1 C LP450G9947 Pump Housing 1 D LP450H0092 Check Valve Assembly 1 E LP50G9945 Gear Set 1 MODEL LP650P10Q MAX FLOW = 10 qt/min (9.5 liter/min) MAX PRESSURE = 650 psi (44.8 bar) NOMINAL CURRENT DRAW 115VAC NOMINAL CURRENT DRAW = VAC PRESSURE SENSING ON/OFF SWITCH = Set at 650 psi FACTORY WIRED FOR 230VAC NOTE: Not recommended for use with 115VAC power unless circuit is fitted with appropriate breaker and wire size to handle motor load. 1 Incl. w/motor Motor Mounting Bracket 1 2 LP50H0027 Quick-Detach Bung Adapter 1 A LP650G9961 Motor 1 1/2 HP,115/230VAC,1700 rpm 1 B LP200H0067 Bypass Spring 1 C LP450G9947 Pump Housing 1 D LP450H0092 Check Valve Assembly 1 E LP50G9945 Gear Set 1 12

13 Fill-Rite: A Worldwide Reputation for Reliability. For over 40 years, people all over the world who have needed tough, dependable pumps have insisted on Fill- Rite products. For them, Fill-Rite has been the reliable red pump that keeps on working even under the toughest of conditions. We re proud of the reputation our hand pumps, DC and AC pumps and meters have earned. Today they re only a part of the rapidly expanding Fill-Rite line. Applying the Science of Fluid Transfer. An active research and development program is the centerpiece of our ongoing commitment to respond to new fluid transfer opportunities. This has led to new products and to new technologies and new facilities to produce these products. To bring this advanced technology to market, we have invested in precision engineering and testing equipment. This improves our ability to produce fluid handling equipment that meets market demands for quality, performance and price. A Hard Working Support Network. Just as important as these capabilities are the people behind them - our design and production personnel. They give you the ability to specify systems that meet the most challenging of applications. With them, you can be assured of prompt, intelligent answers to your fluid transfer questions. To service customers in the field, we ve put together a select, well-monitored team of distributors. Throughout the world, they are ready to help you with technical advice, ordering and delivery. Fill-Rite will always stand for reliable red pumps and fluid handling equipment. We ll continue to develop new products and production techniques to keep pace with ever changing technologies. Each of our products will always be made with the same care and quality that made our pumps famous. PRODUCT WARRANTY Tuthill Transfer Systems ( Manufacturer ) warrants to each consumer buyer of its Fill-Rite products (the Buyer ), from the date of invoice or sales receipt, that goods of its manufacture ( Goods ) will be free from defects of material and workmanship. Duration of this warranty is as follows: Heavy Duty Products - Two years Standard Duty Products One year Economy Duty Products One year Lube Transfer Products One year Cabinet pumps, Parts, and Accessories - One year Manufacturer s sole obligation under the foregoing warranties will be limited to either, at Manufacturers option, replacing or repairing defective Goods (subject to limitations hereinafter provided) or refunding the purchase price for such Goods theretofore paid by the Buyer, and Buyer s exclusive remedy for breach of any such warranties will be enforcement of such obligations of Manufacturer. If Manufacturer so requests the return of the Goods, the Goods will be redelivered to Manufacturer in accordance with Manufacturer s instructions F.O.B. Factory. The remedies contained herein shall constitute the sole recourse of the Buyer against Manufacturer for breach of warranty. IN NO EVENT SHALL MANUFACTURER S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF THE MANUFACTURE, SALE, DELIVERY, OR USE OF THE GOODS EXCEED THE PURCHASE PRICE OF THE GOODS. The foregoing warranties will not extend to Goods subjected to misuse, neglect, accident or improper installation or maintenance, or which have been altered or repaired by anyone other than Manufacturer or its authorized representative. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE OF ANY OTHER TYPE, WHETHER EXPRESS OR IMPLIED. No person may vary the foregoing warranties and remedies except in writing signed by a duly authorized officer of Manufacturer. Warranties or remedies that differ from the foregoing shall not otherwise be binding on Manufacturer. The Buyer s acceptance of delivery of the Goods constitutes acceptance of the foregoing warranties and remedies, and all conditions and limitations thereof. LP50G9954 rev 1 13