WARNING CONTRACTORS SERIES BLAST MACHINE 4 AND 6 CU. FT. WITH MILLENNIUM ACS PNEUMATIC REMOTE CONTROLS 0. M

Size: px
Start display at page:

Download "WARNING CONTRACTORS SERIES BLAST MACHINE 4 AND 6 CU. FT. WITH MILLENNIUM ACS PNEUMATIC REMOTE CONTROLS 0. M"

Transcription

1 CONTRACTORS SERIES BLAST MACHINE 4 AND 6 CU. FT. WITH MILLENNIUM ACS PNEUMATIC REMOTE CONTROLS 0. M. 558 MC FILE NUMBER: 085/0899 DATE OF ISSUE: 08/99 REVISION: E, 0/ CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 6090 Phone (66) FAX (800) info@clemcoindustries.com Do not proceed with these instructions until you have READ the preface of this MANUAL and YOU UNDERSTAND its contents. These S are included for the health and safety of the operator and those in the immediate vicinity. Keep this manual for future reference.

2 PREFACE Read and follow ALL instructions before using this equipment. Failure to comply with ALL instructions can result in serious injury or death. In the event that the user, or any assistants of the user of this equipment cannot read or cannot completely understand the warnings and information contained in these instructions, the employer of the user and his assistants must thoroughly educate and train them on the proper operation and safety procedures of this equipment. NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS AND THIS INFORMATIONAL MATERIAL The products described in this material, and the information relating to those products, is intended for knowledgeable, experienced users of abrasive blasting equipment. No representation is intended or made as to the suitability of the products described herein for any particular purpose or application. No representations are intended or made as to the efficiency, production rate, or the useful life of the products described herein. Any estimate regarding production rates or production finishes are the responsibility of the user and must be derived solely from the user s experience and expertise, and must not be based on information in this material. The products described in this material may be combined by the user in a variety of ways for purposes determined solely by the user. No representations are intended or made as to the suitability or engineering balance of the combination of products determined by the user in his selection, nor as to the compliance with regulations or standard practice of such combinations of components or products. Abrasive Blast Equipment is only a component of the range of equipment used in an abrasive blasting job. Other products may include an air compressor, abrasive, scaffolding, hydraulic work platforms or booms, paint spray equipment, dehumidification equipment, air filters and receivers, lights, ventilation equipment, parts handling equipment, specialized respirators, or equipment that while offered by Clemco may have been supplied by others. Each manufacturer and supplier of the other products used in the abrasive blasting job must be contacted for information, training, instruction and warnings with regard to the proper and safe use of their equipment in the particular application for which the equipment is being used. The information provided by Clemco is intended to provide instruction only on Clemco products. All operators must be trained in the proper, safe, use of this equipment. It is the responsibility of the users to familiarize themselves with, and comply with, all appropriate laws, regulations, and safe practices that apply to the use of these products. Consult with your employer about training programs and materials that are available. Our company is proud to provide a variety of products to the abrasive blasting industry, and we have confidence that the professionals in our industry will utilize their knowledge and expertise in the safe efficient use of these products. GENERAL INSTRUCTIONS Described herein are some, BUT NOT ALL, of the major requirements for safe and productive use of blast machines, remote control systems, operator respirator assemblies, and related accessories. Completely read ALL instruction manuals prior to using equipment. The user's work environment may include certain HAZARDS related to the abrasive blasting operation. Proper protection for the blaster, as well as anyone else that may be EXPOSED to the hazards generated by the blasting process, is the responsibility of the user and/or the employer. Operators MUST consult with their employer about what hazards may be present in the work environment including, but not limited to, exposure to dust that may contain TOXIC MATERIALS due to the presence of silica, cyanide, arsenic or other toxins in the abrasive, or materials present in the surface to be blasted such as lead or heavy metals in coatings. The environment may also include fumes that may be present from adjacent coatings application, contaminated water, engine exhaust, chemicals, and asbestos. The work area may include PHYSICAL HAZARDS such as an uneven work surface, poor visibility, excess noise, and electrical hazards. The operator MUST consult with his employer on the identification of potential hazards, and the appropriate measures that MUST be taken to protect the blaster and others that might be exposed to these hazards. ALL machines, components and accessories MUST be installed, tested, operated and maintained only by trained, knowledgeable, experienced users. DO NOT modify or substitute any Clemco parts with other types or brands of equipment. Unauthorized modification and parts substitution on supplied air respirators is a violation of OSHA regulations and voids the NIOSH approval. OPERATIONAL INSTRUCTIONS OPERATOR SAFETY EQUIPMENT Blast operators and others working in the vicinity of abrasive blasting must always wear properlymaintained, NIOSH-approved, respiratory protection appropriate for the job site hazards. DO NOT USE abrasives containing more than one percent crystalline (free) silica. Ref. NIOSH Alert #9-0 Inhalation of toxic dust (crystalline silica, asbestos, lead paint and other toxins) can lead to serious or fatal disease (silicosis, asbestosis, lead or other poisoning). ALWAYS wear NIOSH-approved supplied-air respirators as required by OSHA, in the presence of any dust including, but not limited to, handling or loading abrasive; blasting or working in the vicinity of blast jobs; and cleanup of expended abrasive. Prior to removing respirator, an air monitoring I

3 PREFACE instrument should be used to determine when surrounding atmosphere is clear of dust and safe to breathe. NIOSH-approved, supplied-air respirators are to be worn ONLY in atmospheres: NOT IMMEDIATELY dangerous to life or health and, from which a user can escape WITHOUT using the respirator. Clemco supplied-air respirators DO NOT REMOVE OR PROTECT AGAINST CARBON MONOXIDE (CO) OR ANY OTHER TOXIC GAS. Carbon monoxide and toxic gas removal and/or monitoring device must be used in conjunction with respirator to insure safe breathing air. Air supplied to respirator MUST BE AT LEAST GRADE D QUALITY as described in Compressed Gas Association Commodity Specification G-7., and as specified by OSHA Regulation 90.9 (d). ALWAYS locate compressors to prevent contaminated air (such as CO from engine exhaust) from entering the air intake system. A suitable in-line air purifying sorbent bed and filter or CO Monitor should be installed to assure breathing air quality. ALWAYS use a NIOSH-approved breathing air hose to connect an appropriate air filter to the respirator. Use of a nonapproved air hose can subject the operator to illness caused by the release of chemical agents used in the manufacture of nonapproved breathing air hose. ALWAYS check to make sure air filter and respirator system hoses are NOT CONNECTED to in-plant lines that contain nitrogen, acetylene or any other non-breathable gas. NEVER use oxygen with air line respirators. NEVER modify air line connections to accommodate air filter/respirator breathing hose WITHOUT FIRST testing content of the air line. FAILURE TO TEST THE AIR LINE MAY RESULT IN DEATH TO THE RESPIRATOR USER. Respirator lenses are designed to protect against rebounding abrasive. They do not protect against flying objects, glare, liquids, radiation or high speed heavy materials. Substitute lenses from sources other than the original respirator manufacturer will void NIOSH-approval of this respirator. BLAST MACHINES AND REMOTE CONTROLS ALWAYS equip abrasive blast machines with remote controls. Abrasive blast machine operators must wear NIOSHapproved supplied-air respirators (ref: OSHA regulations 90.94, 90., 90.9 and 90.44). NEVER modify OR substitute remote control parts. Parts from different manufacturers are NOT compatible with Clemco equipment. If controls are altered, involuntary activation, which may cause serious injury, can occur. Inspect the air control orifice DAILY for cleanliness. NEVER use welding hose in place of twinline control hose. The internal diameter and rubber composition are UNSAFE for remote control use. UNLESS OTHERWISE SPECIFIED, maximum working pressure of blast machines and related components MUST NOT exceed National Board approved 5 psig (8.5 BAR). NEVER weld on blast machine. Welding may affect dimensional integrity of steel wall and WILL VOID National Board approval. Point nozzle ONLY at structure being blasted. High velocity abrasive particles WILL inflict serious injury. Keep unprotected workers OUT of blast area. NEVER attempt to manually move blast machine when it contains abrasive. EMPTY machines, up to 6 cu. ft.(70kg) capacity, are designed to be moved: on flat, smooth surfaces by AT LEAST two people; with the Clemco "Mule"; or with other specially designed machine moving devices. Larger empty blast machines or ANY blast machine containing abrasive MUST be transported by mechanical lifting equipment. AIR HOSE, BLAST HOSE, COUPLINGS, AND NOZZLE HOLDERS Air hose, air hose fittings and connectors at compressors and blast machines MUST be FOUR times the size of the nozzle orifice. Air hose lengths MUST be kept as short as possible AND in a straight line. Inspect DAILY and repair leakage IMMEDIATELY. Blast hose inside diameter MUST be THREE to FOUR times the size of the nozzle orifice. AVOID sharp bends that wear out hose rapidly. Use SHORTEST hose lengths possible to reduce pressure loss. Check blast hose DAILY for soft spots. Repair or replace IMMEDIATELY. ALWAYS cut loose hose ends square when installing hose couplings and nozzle holders to allow uniform fit of hose to coupling shoulder. NEVER install couplings or nozzle holders that DO NOT provide a TIGHT fit on hose. ALWAYS use manufacturers recommended coupling screws. Replace coupling gaskets FREQUENTLY to prevent leakage. Abrasive leakage can result in dangerous coupling failure. ALL gaskets MUST be checked SEVERAL times during a working day for wear, distortion and softness. Install safety pins at EVERY coupling connection to prevent accidental disengagement during hose movement. ALWAYS attach safety cables at ALL air hose AND blast hose coupling connections. Cables relieve tension on hose and control whipping action in the event of a coupling blow-out. II

4 PREFACE MAINTENANCE ALWAYS shut off compressor and depressurize blast machine BEFORE doing ANY maintenance. Always check and clean ALL filters, screens and alarm systems when doing any maintenance. ALWAYS cage springs BEFORE disassembling valves IF spring-loaded abrasive control valves are used. ALWAYS completely follow owner's manual instructions and maintain equipment at RECOMMENDED intervals. ADDITIONAL ASSISTANCE Training and Educational Programs. Clemco Industries Corp. offers a booklet, Blast-Off, developed to educate personnel on abrasive blast equipment function and surface preparation techniques. Readers will learn safe and productive use of machines, components and various accessories, including selection of abrasive materials for specific surface profiles and degrees of cleanliness. The Society for Protective Coatings (SSPC) offers a video training series on protective coatings including one entitled "Surface Preparation." For loan or purchase information, contact SSPC at the address shown below. TECHNICAL DATA AND RESEARCH COMMITTEES The following associations offer information, materials and videos relating to abrasive blasting and safe operating practices. The Society for Protective Coatings (SSPC) 40 4th Street, Pittsburgh PA Phone: (4) 8- FAX (4) research@sspc.org Website: National Association of Corrosion Engineers (NACE) 440 South Creek Drive, Houston TX Phone: (8) FAX (8) msd@mail.nace.org Website: American Society for Testing and Materials (ASTM) 00 Barr Harbor Dr., West Conshohocken, PA 948 Phone (60) FAX (60) service@astm.org Website: NOTICE This equipment is not intended to be used in an area that might be considered a hazardous location as described in the National Electric Code NFPA , article 500. WARRANTY The following is in lieu of all warranties express, implied or statutory and in no event shall seller or its agents, successors, nominees or assignees, or either, be liable for special or consequential damage arising out of a breach of warranty. This warranty does not apply to any damage or defect resulting from negligent or improper assembly or use of any item by the buyer or its agent or from alteration or attempted repair by any person other than an authorized agent of seller. All used, repaired, modified or altered items are purchased as is and with all faults. In no event shall seller be liable for consequential or incidental damages. The sole and exclusive remedy of buyer for breach of warranty by seller shall be repair or replacement of defective parts or, at seller s option, refund of the purchase price, as set forth below:.seller makes no warranty with respect to products used other than in accordance hereunder..on products seller manufactures, seller warrants that all products are to be free from defects in workmanship and materials for a period of one year from date of shipment to buyer, but no warranty is made that the products are fit for a particular purpose..on products which seller buys and resells pursuant to this order, seller warrants that the products shall carry the then standard warranties of the manufacturers thereof, a copy of which shall be made available to customer upon request. 4.The use of any sample or model in connection with this order is for illustrative purposes only and is not to be construed as a warranty that the product will conform to the sample or model. 5.Seller makes no warranty that the products are delivered free of the rightful claim of any third party by way of patent infringement or the like. 6.This warranty is conditioned upon seller s receipt within ten (0) days after a buyer s discovery of a defect, of a written notice stating in what specific material respects the product failed to meet this warranty. If such notice is timely given, seller will, at its option, either modify the product or part to correct the defect, replace the product or part with complying products or parts, or refund the amount paid for the defective product, any one of which will constitute the sole liability of seller and a full settlement of all claims. No allowance will be made for alterations or repairs made by other than those authorized by seller without the prior written consent of seller. Buyer shall afford seller prompt and reasonable opportunity to inspect the products for which any claim is made as above stated. Except as expressly set forth above, all warranties, express, implied or statutory, including implied warranty of merchantability, are hereby disclaimed. DAILY SET-UP CHECK LIST ALL piping, fittings and hoses MUST be checked DAILY for tightness and leakage. ALL equipment and components MUST be thoroughly checked for wear. ALL worn or suspicious parts MUST be replaced. ALL blast operators MUST be properly trained to operate equipment. ALL blast operators MUST be properly outfitted with abrasive resistant clothing, safety shoes, leather gloves and ear protection. BEFORE blasting ALWAYS use the following check list.. PROPERLY MAINTAINED AIR COMPRESSOR sized to provide sufficient volume (cfm) for nozzle and other tools PLUS a 50% reserve to allow for nozzle wear. Use large compressor outlet and large air hose (4 times the nozzle orifice size). FOLLOW MANUFACTURERS MAINTENANCE INSTRUCTIONS.. BREATHING AIR COMPRESSOR (oil-less air pump) capable of providing Grade D Quality air located in a dust free, contaminant free area. If oil-lubricated air compressor is used to supply respirator, it should have high temperature monitor and CO monitor or both. If CO monitor is not used, air MUST be tested FREQUENTLY to ensure proper air quality. III

5 PREFACE. Clean, properly maintained NIOSH-APPROVED SUPPLIED-AIR RESPIRATOR. ALL components should ALWAYS be present. NEVER operate without inner lens in place. Thoroughly inspect ALL components DAILY for cleanliness and wear. ANY substitution of parts voids NIOSH approval i.e. cape, lenses, breathing hose, breathing air supply hose, air control valve, cool air or climate control devices. 4. OSHA required BREATHING AIR FILTER for removal of moisture and particulate matter from breathing air supply. THIS DEVICE DOES NOT REMOVE OR DETECT CARBON MONOXIDE (CO). ALWAYS USE CO MONITOR ALARM. 5. ASME CODED BLAST MACHINE sized to hold / hour abrasive supply. ALWAYS ground machine to eliminate static electricity hazard. Examine pop up valve for alignment. Blast machine MUST be fitted with a screen to keep out foreign objects and a cover to prevent entry of moisture overnight. 8. BLAST HOSE with ID to 4 times the nozzle orifice. Lines MUST be run AS STRAIGHT AS POSSIBLE from machine to work area with NO sharp bends. Check DAILY for internal wear and external damage. 9. HOSE COUPLINGS, NOZZLE HOLDERS fitted SNUGLY to hose end and installed using PROPER coupling screws. Coupling lugs MUST be snapped FIRMLY into locking position. Gasket MUST form positive seal with safety pins inserted through pin holes. Check gaskets and replace if ANY sign of wear, softness or distortion. ALWAYS install safety cables at every connection to prevent disengagement. Check nozzle holder for worn threads. NEVER MIX DIFFERENT BRANDS OF COMPONENTS. Check each of these components DAILY. 0. Inspect NOZZLE and GASKET DAILY for wear. Replace nozzle when /6" larger than original size or if liner appears cracked. Check nozzle threads for wear. 6. AIR LINE FILTER installed AS CLOSE AS POSSIBLE to machine inlet. Sized to match inlet piping or larger air supply line. Clean filter DAILY. Drain OFTEN. 7. REMOTE CONTROLS MUST be in PERFECT operating condition. ONLY use APPROVED spare parts, including twin- line hose. DAILY: test system operation and check button bumper and spring action of lever and lever lock. DO NOT USE WELDING HOSE.. Use abrasive that is properly sized and free of harmful substances; such as, free silica, cyanide, arsenic or lead. Check material data sheet for presence of toxic or harmful substances.. Test surface to be blasted for toxic substances. Take appropriate, and NIOSH required, protective measures for operator and bystanders which pertain to substances found on the surface to be blasted. Air Compressor. Silica-free Abrasive 5. ASME Coded Blast Machine. Breathing Air Compressor (or). Ambient Air Pump for low pressure respirator. NIOSH Approved Supplied-Air Respirator 7. Remote Controls 6. Air Line Filter 4. CPF Air-Filter 0. Appropriately Sized Nozzle 9. Hose Couplings and Safety Cables 8. Blast Hose IV

6 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page.0 INTRODUCTION. Scope of manual.. These instructions cover the set-up, operation, maintenance, troubleshooting, and replacement parts for the following Clemco Contractor Series Blast Machines with pneumatic Millennium Remote Controls and abrasive cut-off (ACS): 0" diameter, 4 cu. ft. capacity 4" diameter, 6 cu. ft. capacity.. These instructions also contain important information required for safe operation of the machine. All blast operator(s) and machine (pot) tenders must be trained in the safe operation of the blast machine, remote control system, and all blasting accessories. Before using the machine, all personnel involved with the blast machine operation must read this entire manual, including the orange cover, and all accessory manuals... All personnel involved with the abrasive blasting process must be made aware of the hazards associated with abrasive blasting. The Clemco booklet "Abrasive Blasting Safety Practices" is included with every blast machine, and contains important safety information about abrasive blasting that may not be included in equipment operation manuals. Additional copies are available from Clemco Industries.. Safety Alerts.. Clemco uses safety alert signal words, based on ANSI Z , to alert the user of a potentially hazardous situation that may be encountered while operating this equipment. ANSI's definitions of the signal words are as follows: This is the safety alert symbol. It is used to alert the user of this equipment of potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. CAUTION Caution used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. CAUTION Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. DANGER Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.. Components and Operating Principles.. Components... The primary components of the Contractor machines are shown in Figure. They include the blast machine with Millennium Remote Controls, pneumatically operated Auto-Quantum Abrasive Metering Valve, frame assembly, optional air filters... Instruction Maintenance Manuals... Individual manuals are included with the following optional accessories: CPF Air Filter Apollo Respirator Cool Air Tube... The front leg contains a storage area for owners manuals. After reviewing all the manuals, and start-up and adjustments are completed, remove the urethane cover plate and store manuals in the compartment, for future reference... Blast Machine... Clemco blast machines (pressure vessels) are manufactured to American Society of Mechanical Engineers (ASME) standards, as described in Section VII, Div., and carry a National Board certification. It is the owner's responsibility to maintain the integrity of the vessel as may be required by some states. This may include regular inspection and hydrostatic testing as described in National Board Inspection Code and Jurisdictional Regulations and /or Laws.

7 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page Cover (Optional Accessory) Hose Safety Cable (Optional Accessory) Lifting Eye Screen (Optional Accessory) Pop-up Seal Pop-up Valve Lifting Eye Compression Coupling Choke Valve Abrasive Trap Pusher Line Inspection Door Owners Manual Storage Tube Cover Exhaust Muffler Millennium Valve Bulkhead Fittings (Control Hose Connection) Compressed Air Inlet Quick Coupling (Blast Hose Connection) Auto-Quantum Metering Valve (Standard Metering Valve) Air filter (Optional Accessory) Breathing-Air Inlet CPF Filter (Optional Accessory) Figure Welding, grinding, or drilling on the blast machine could weaken the vessel. Compressed air pressure could cause a weakened blast machine to rupture, resulting in death or serious injury. Welding, grinding, or drilling on the blast machine vessel, without a National Board ²R² stamp voids the ASME and National Board certification.... All welding repairs done on the vessel must be performed by certified welders, at shops holding a National Board "R" Stamp. Welding performed by any welder not properly qualified per the ASME Code voids ASME and National Board certification of the vessel.... This blast machine is rated for a maximum of 50 psi (pounds per square inch); do not exceed the rated pressure. Excessive air pressure could cause a blast machine to rupture. To prevent serious injury or death, do not exceed the rated pressure of the blast machine vessel....4 Use lifting eyes to assist in loading and unloading the blast machine. Do not use a sling around the cart handles or piping....5 The blast machine is equipped with remote controls that allow the operator to pressurize the machine to start blasting, and depressurize it to stop blasting, at the nozzle.

8 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page...6 OSHA does not require pressure relief valves on blast machines when air compressors supplying air to the blast machines are built to ASME () specifications and comply with OSHA () regulations. ASME Manual section VIII, Division, UG-5, paragraph A90 (g) states that pressure relief valves or protective devices "...need not be installed directly on a pressure vessel when the source of pressure is external to the vessel and is under such positive control that the pressure in the vessel cannot exceed the maximum allowable working pressure at the operating temperature...". OSHA regulation refers to the above ASME code when describing the necessity of pressure relief valves on compressed air equipment. DO NOT operate blast machines with air compressors that are not equipped with properly functioning pressure relief valves. () American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, 989 () Occupational Safety and Health Administration, 9 CFR 90, Subpart M - Compressed Gas and Compressed Air Equipment...4 Remote Controls..4. The components of the Millennium remote control system with ACS are shown in Figure. They include the Millennium Valve, Auto-Quantum pneumatically operated abrasive metering valve, RLX Control Handle with ACS air switch assembly, 50-foot twinline control hose, 50-foot single-line control hose, 8-inch hose, 4-foot long twinline control hose, and all necessary fittings...4. The remote control system is an OSHA-required safety device. The control handle, located near the blast nozzle, is the activator for the remote control system. When the operator intentionally or unintentionally removes hand-held pressure from the remote control handle, the machine depressurizes, stopping air and abrasive flow through the nozzle. The remote control system "fails to safe", which means any interruption in the control-air circuit for reasons, such as a break in the line, the compressor stops running, or the operator drops the blast hose, the remote controls deactivate the blast machine. Never modify or substitute remote control parts. Parts from other manufacturers are not compatible with Clemco equipment. If ANY part of the remote control system is altered, involuntary activation, which may cause serious injury, can occur. Millennium Valve Some Items are Rotated for Clarity Safety Petcock Return Air Line 4-Foot Twinline Hose Auto-Quantum Metering Valve Orifice Fitting Outbound Air Line Front Leg of Blast Machine Bulkhead Fittings /4" NPT Adaptor 50-Foot Twinline Hose Nylon Tie Nozzle Holder 8-Inch Hose 50-Foot Single-Line Hose ACS Switch RLX Control Handle Figure

9 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page Millennium Remote Controls are pressurerelease-style systems, which control the pressurization and depressurization of the blast machine. Pressurization, which starts blasting, occurs when the control handle is pressed. Depressurization, which stops blasting, occurs when the handle is released Millennium Remote Controls operate pneumatically on the "return air" principle (See Figure ). One stream of air travels down the outbound twinline and escapes through an opening located under the control handle lever. As long as air escapes through the opening, the remote control system remains inactive. When the lever is pressed, the opening is sealed, and air from the outbound line returns through the return line to open the inlet segment and close the outlet segment of the Millennium valve. This pressurizes the blast machine and begins the blasting process. Releasing the handle exhausts the control air, which closes the inlet segment, and opens the outlet segment to depressurize the machine and stop the blasting...5 Abrasive Cut-Off (ACS)..5. The abrasive cut-off switch is mounted on the control handle. The operator uses the switch to close the abrasive valve independently of the air valve, so air without abrasive exits the nozzle...6 Electric Remote Control Option..6. Electric remote controls (electro-pneumatic) are recommended when the nozzle and remote control handle are farther than 00 feet from the blast machine. Pressure drop of pneumatic systems over longer distances increases actuation time, which prevents fast, safe operation. Contact your local Clemco Distributor for more information...7 Air Filter, Optional..7. The optional filter removes particles and condensed moisture from the compressed air before it enters the machine. Water is drained by use of a manual drain located at the bottom of the filter...8 Frame and Cart..8. The frame assembly provides added protection for the piping, valves and accessories. This protection keeps the piping aligned and tight. The wheeled cart assists in the mobility of the machine over smooth flat surfaces. See transporting and moving in Section...0 INITIAL SET-UP Moist air that freezes could cause blockage at the control handle or in the control lines. Blockage could cause involuntary activation of the remote controls, or prevent the controls from deactivating upon release of the control handle. This situation could result in serious injury or death. If remote controls are operated in freezing or near freezing weather, install a Clemco Anti-Freeze Injector, stock no. 0557, on the remote control air supply line.. Blast Hose and Control Hose Connections, See Figure... Locate the three /4" NPT adaptors, packaged in the accessory box. The adaptors are boxed, to prevent damage in transit... Screw the adaptors tightly into the bulkhead fittings on the lower part of the front leg... Uncoil the blast hose, and lay the 50-ft. twinline hose and 50-foot single-line hose alongside it. Hoses should be of equal lengths...4 Band the control handle to the blast hose close to the nozzle holder, using the two nylon ties provided. Once the control is firmly attached, clip the tie ends so they will not snag the operator's clothing or interfere with the operation of the control handle. Where two or more blast machines are used, carefully trace, connect, and mark, control cord, and blast hose. Cross connecting control hose or blast hose could lead to serious injury, death, or property damage from unintentional actuation of a blast machine. To prevent cross connections, hoses should be of equal lengths, and the hoses and blast machine couplings clearly marked. Use optional hose identification kits, part no for use with two blast machines, or part no. 589 for up to four machines. Mark each hose and connection per the instructions supplied with the kit, and carefully trace and verify each connection before operating.

10 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 5..5 Attach the 50-foot twinline hose to the two fittings on the back of the control handle. Either side of the hose can be attached to either fitting...6 Attach the 50-foot single-line control hose to the fitting on the ACS Switch mounted on the control handle...7 Working from the control handle back, band the twinline and single-line hoses to the blast hose every four to six feet, and as close to the couplings as possible...8 Place the nozzle washer in the nozzle holder, and screw the nozzle into the holder. The nozzle must seat tightly against the nozzle washer.. Compressed-Air Supply Hose Connection.. Install an air supply hose fitting to the optional air filter or air inlet that is compatible with the compressed-air supply hose from the compressor. See Section.... Breathing Air Connections, Optional CPF Filter Air supply to the respirator system is critical to the safety of the user. Read the CPF Filter and Apollo Respirator manuals carefully. Poor quality air will cause serious respiratory injury or death to the user... Breathing air must meet the requirements for Grade D or higher quality, as described in Compressed Gas Association Commodity Specification pamphlet G- 7.., titled Commodity Specification For Air, Published by Compressed Gas Association Inc., Chantilly, VA. (CFR Title 0 Chapter ). DANGER Do not connect the CPF Filter, or any other regulator or filter, to bottled air or any other air source that does not have a pressure-reducing valve that reduces pressure to maximum of 50 psi. Failure to comply with this warning will cause low pressure devices to explode under the high pressure of bottled air. Such an explosion could cause severe injury or death... Connect an air supply hose fitting to the filter inlet, which is compatible with the air supply hose from an air source that meets OSHA requirements for respirable air, to the CPF Filter inlet as shown in Figure. Pressure supplied to the filter must not exceed 50 psi... For models with CPF filter only: Connect the respirator lead hose to the compatible fitting on the CPF filer. Refer to the Apollo Respirator and CPF Filter manuals for instructions concerning their operation..0 OPERATION. Transporting and Moving.. Transporting a blast machine... Always empty the machine before transporting. Transporting the machine containing abrasive could increase the weight to an unsafe handling limit, and could cause abrasive to settle in piping. Always empty the blast machine before lifting or hoisting. Use the lifting eyes when lifting the machine. Never hoist the machine by the handle or piping, or with a sling through the handle or piping. Always use lift equipment that is rated higher than the weight of the machine and accessories. When transporting a machine on a pallet, always securely attach the machine to a sturdy pallet. Always securely anchor the machine to the transport vehicle. Anyone using material handling equipment to move, transport, or lift the machine must be experienced, and able to recognize and avoid hazards associated with handling this type of machinery, and to safely operate the equipment. Failure to observe these warnings could result in serious injury or death... Moving a blast machine Never attempt to manually move a blast machine when it contains abrasive. An empty machine may be moved when the following criteria are met:

11 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 6... An empty machine may be moved manually, on level flat surfaces. Do not manually move the machine on an incline, or on a slippery or irregular surface that could cause the operator to slip or lose balance. Sudden weight shifts when the machine is tilted on an incline, and slipping or tripping while moving the machine will cause the operator to lose control of the machine, causing severe injury and property damage.... Move the machine by pushing it forward. Do not back-up while moving the machine, as potential tripping hazards may be out of view.... Use the lifting eyes when lifting the machine. Do not use a sling around the cart handles or piping....4 If the machine contains any abrasive, keep the machine upright. Laying down a machine containing abrasive could cause abrasive to lodge in the piping and cause the machine to malfunction, or cause damage to the valves. Hose disconnection while under pressure could cause serious injury or death. Use safety lock pins and safety cables on all coupling connections to help prevent hose couplings from accidental disconnection...5 Connect the ends of the 50-foot twinline hose to the lower adaptors in the bulkhead fittings on the front leg as shown in Figure. Either side of the hose can be attached to either fitting. Make sure all fittings are tight. Leaks will cause the system to malfunction. Single-Line Hose Adaptor Twinline Hose Adaptors Front Leg. Start-Up.. Locate the compressor upwind from the blasting operation to prevent contaminated air from entering the compressor intake... Connect an line from the compressor to the air supply hose connector installed on the blast machine inlet. For best blasting performance, use -/4" ID or larger air line when using up to a 5/6" orifice nozzle, - /" or larger when using up to a /8" nozzle, and " or larger when using up to a /" nozzle. See the compressed air and abrasive consumption chart in Figure 4 for approximate air consumption... Make sure the coupling gaskets are in place and in good condition before connecting the blast hose to the quick coupling on the blast machine. When connecting the hose make sure the coupling spring lock pins are at 80 degrees (Pins should enter the unused hole of the adjoining coupling). The spring lock pins help prevent accidental separation of hose couplings during blasting...4 Make sure that all compressed-air supply hose connections are secured with safety lock pins and safety cables to prevent accidental separation or disconnection. Safety cables are listed in Section 8. of this manual. Figure..6 Connect the end of the 50-foot single-line to the top adaptor as shown in Figure. Make sure all fittings are tight. Leaks will cause the system to malfunction...7 Connect an air line between a source of respirable breathing air meeting the requirements for Grade D or higher quality, and the CPF filter inlet. See Section.. The maximum inlet pressure for the CPF Filter must not exceed 50 psi. DANGER Do not connect the CPF Filter, or any other regulator or filter, to bottled air or any other air source that does not have a pressure reducing valve that reduces pressure to a maximum of 50 psi. Failure to comply with this warning will cause low pressure devices to explode under the high pressure of bottled air. Such an explosion could cause severe injury or death.

12 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 7..8 Make sure that all blast hose and compressedair hose connections are secure, and that coupling lock pins are in place...9 Make sure the choke valve is open, (handle inline with the valve and piping)...0 Make sure that all blast hose and compressedair hose connections are secure, and that coupling lock pins are in place. If twist-on type air hose couplings are used, they must be secured by safety pins or wires to prevent accidental disconnection. Hose disconnection while under pressure could cause serious injury or death... Make sure the choke valve is open, (handle inline with the valve and piping). Compressed Air and Abrasive Consumption Consumption rates are based on abrasive that weigh 00 pounds per cubic foot Nozzle Pressure At The Nozzle (psi) Air, Power Orifice and Abrasive Size (in.) Requirements Air (cfm) No Abrasive lbs/hr) /8" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) /6" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) /4" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) 5/6" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) /8" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) 7/6" Compressor (hp) Air (cfm) No Abrasive (lbs/hr) /" Compressor (hp) For nozzle sizes /8" to /", blast machines should be equipped with -/4" or larger piping and inlet valve to prevent pressure loss. Air requirements were measured by a flow meter under actual blasting conditions, and are therefore lower than figures for air alone, with no abrasive. Horsepower requirements are based on 4.5 cfm per horsepower. Figures are for reference only, and may vary for different working conditions. Several variables, including metering valve adjustments, can affect abrasive flow. Figures show approximate compressed air and abrasive consumption when nozzles are new. Consumption will increase as the nozzle wears. Figure 4

13 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 8.. Close the Quantum abrasive metering valve. Closed position is when the knob is turned fully clockwise. See Section Open the safety petcock on the inlet section of the Millennium valve. It is open when the lever is in-line with the petcock, as shown in Figure 5. To prevent severe injury or death from accidental activation of the blast machine, open the safety petcock when the blast machine is not in use. Opening the petcock prevents unintentional blasting. The control handle can not activate the machine when the petcock is open...4 Make sure that the control handle lever is in the up (no blast) position, and that the handle lever and safety lock move freely. Closed Open Figure 5..5 Check to make sure that the handle lever will not seal the opening on the control handle, unless the safety lever lock is pulled down. Malfunctioning control handles could cause unintentional actuation of a blast machine, or prevent a machine from deactivating upon release. Malfunctioning control handles must be taken out of service immediately and repaired or replaced. Serious injury or death can result from unintentional blasting...6 Close the air valve on the compressor. Start the compressor, and bring it to operating temperature and pressure. The pressure must be more than 0 psi, but not exceed 50 psi...7 Slowly open the compressor air valve, to pressurize the air supply line. Listen for any open lines or leaks...8 Pressurize the breathing air supply line, and adjust pressure on the CPF Filter outlet, to the pressure stated in the respirator manual...9 Load abrasive into the machine by following the instructions in Section Do not allow anyone within 0 feet of the blast machine except machine tenders, who are appropriately fitted with approved protective equipment. The blast operator could pressurize and depressurize the machine without warning. All persons except for the machine tender must stay clear of the blast machine. The blast operator may pressurize or depressurize the machine at any time. The noise generated by the sudden release of compressed air when the machine is pressurized or depressurized, may startle bystanders, and may vent abrasive under pressure. Either condition could result in injury. The machine tender must wear a suitable, approved respirator, plus approved eye, face, and hearing protection... When the blast operator is ready to blast, either the operator or the machine tender, while standing back and facing away from the concave filling head of the blast machine and the exhaust muffler, closes the safety petcock. Closing the petcock prepares the machine for remote operation and activation by the control handle. Air should be heard escaping from the orifice under the control handle lever but nowhere else. The noise from air escaping at the control handle is an audible signal that air is supplied to the blast machine, and will activate if the control handle is pressed.. Blasting Attire.. Operators and anyone else that may be exposed to the hazards generated by the blasting process must wear appropriate protective gear, including abrasive-resistant clothing, leather gloves, eye and hearing protection, and a NIOSH-approved Type CE Supplied-Air Respirator.

14 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 9 Before blasting, test the coating and substrate for toxic materials (such as lead or other heavy metals, or asbestos). These hazards require special measures to protect the operators and the environment. No dust is safe to breathe. Abrasive blasting produces harmful dust. Failure to wear approved respirators could result in serious lung disease or death. Blast operators must wear properly fitted and maintained NIOSHapproved, type-ce supplied-air respirators approved for abrasive blasting. During abrasive blasting, abrasive particles and dust in the area around the blast machine and blast nozzle become airborne. Everyone working in the vicinity of abrasive blasting must wear properly-maintained, NIOSH-approved, respiratory protection appropriate for the job site hazards. Loud noise generated by the use of compressed air could cause hearing damage. Everyone in the blasting area must wear approved eye and hearing protection..4 Blasting.4. Hold the blast hose securely and point the nozzle only at objects intended to be blast cleaned..4. Pull back the safety lever lock and depress the remote control handle. Within a few seconds, the pop-up valve automatically closes, and the blast machine pressurizes to start blasting. CAUTION Be prepared for the recoil from the blast hose. Blasting should begin within a few seconds after pressing the control handle lever. OSHA requires the use of remote controls on all blast machines when an operator controls the nozzle. To comply with OSHA regulations, the remote control handle, which starts and stops the flow of air and abrasive, must be held down manually. Do not tie down the control handle lever or attempt to bypass any part of the remote control system. Doing so will defeat the purpose of the fail-to-safe feature of the remote control. Serious injury or death could result from uncontrolled blasting. Ref. 9 CFR (b)..4. If the metering valve is closed, as instructed, only air will exit the nozzle..4.4 Check that the toggle on the ACS switch is pointing away from the nozzle to open the Quantum metering valve. See Section.8 for operation of the ACS..4.5 Adjust abrasive flow per Section Stop Blasting.5. If the blast hose must be blown-out before stopping blasting, Move the toggle on the ACS switch toward the nozzle to close the Quantum metering valve and clear the hose. The See Section.8 for operation of the ACS..5. To stop blasting; release the control handle lever. The outlet section of the Millennium valve opens, and the blast machine depressurizes. The pop-up valve automatically drops when air is expelled from the machine and pressure equalizes..5. When the control handle lever is released, the control handle safety lever will flip up to lock the handle lever in the up (no blast) position..5.4 Make sure that the control handle safety lever lock is up, and that it prevents the handle lever from engaging..5.5 Always open the safety petcock during work breaks and before filling the blast machine. Opening the petcock prevents unintentional blasting.

15 CONTRACTOR SERIES BLAST MACHINE, 4 & 6 CU. FT. Page 0.6 Loading Abrasive into the Blast Machine Obtain a material safety data sheet (MSDS) for the blast abrasive. Abrasive blasting with sands containing crystalline (free) silica can lead to serious or fatal respiratory disease. As NIOSH recommends, do not use abrasives containing more than trace amounts (more than one percent) free silica. When approaching an idle blast machine, and before loading the blast machine with abrasive, always check to make sure the safety petcock is open. If it is closed, open it while standing back and facing away from the concave head and exhaust muffler. This step is especially important if one worker (a machine tender) loads the machine with abrasive while another worker (the blast operator) controls the blasting. The blast operator could pressurize the machine before the machine tender has moved away from the machine. During pressurization, abrasive could be forced out of the top of the machine, and cause injury..6. Load abrasive into the machine by pouring it through the screen into the concave head. Use a screen placed over the head to prevent objects from falling inside. Foreign objects will jam the machine. Abrasive flows through the filling port into the machine. Keep the abrasive level below the pop-up valve. Abrasive resting on the pop-up valve could be forced up and out of the top of the machine when the machine is pressurized. NOTE: Use only abrasives specifically manufactured for blast cleaning, that are compatible with the surface being blasted. Abrasive produced for other applications may be inconsistent in size and shape, and contain particles that could jam the abrasive metering valve, or cause irregular wear. Some abrasive may contain salts, corrosives, or other materials that could contaminate the surface being blasted..6. When the blast operator is ready, either the operator or the machine tender, while standing back and facing away from the concave filling head and exhaust muffler, closes the safety petcock..7 Emptying the Machine of Abrasive.7. When working in environments subject to extreme temperature changes, or very humid conditions, condensation may develop inside the machine. Condensation dampens abrasive and causes flow problems. To prevent this, empty the machine of all abrasive when shutting down for the day. This will eliminate trouble from moist abrasive when starting a new day's blasting. One way to avoid having to empty the machine is to load only as much abrasive as will be used during the work period. If the machine must be purged of abrasive, do the following..7. With the blast machine off, turn the blast pressure to approximately psi, close the choke valve and set the abrasive metering valve at full open..7. To prevent rapid wear of the nozzle holder threads, the nozzle should be firmly attached to the nozzle holder. Removal of the nozzle is not recommended. If circumstances require the nozzle to be removed, also remove the nozzle washer. Purging the machine without a nozzle in place will erode the thread area of the nozzle holder, which could cause a hazardous condition..7.4 Point the nozzle into a drum or suitable container, or in the direction the abrasive is to be disposed..7.5 Hold the hose securely (do not leave the hose unattended), and pressurize the machine by activating the control handle. Be prepared for surging, or recoil of the hose, which can be severe..7.6 When the machine is empty, release the control handle lever, open the safety petcock, and open the choke valve. The threads on the nozzle and nozzle holder must be inspected each time the nozzle is secured to the holder. Make sure the threads are not worn, and that the nozzle holder securely grips the nozzle. The nozzle washer must also be inspected for wear. Worn nozzle washers cause thread erosion. A loose fitting nozzle may eject from the holder under pressure and could cause severe injury..7.7 If the nozzle was removed, thoroughly inspect the nozzle holder threads for wear before installing the nozzle washer and attaching the nozzle.

WARNING. Electronic files include a Preface containing the same important information as the orange cover.

WARNING. Electronic files include a Preface containing the same important information as the orange cover. CONTRACTOR SERIES 4 AND 6 CU. FT. BLAST MACHINE WITH MILLENNIUM PNEUMATIC PRESSURE RELEASE REMOTE CONTROLS O. M. 21941 DATE OF ISSUE: 01/96 REVISION: K, 05/13 2013 CLEMCO INDUSTRIES CORP. One Cable Car

More information

WARNING CLASSIC BLAST MACHINE WITH PNEUMATIC TLR REMOTE CONTROLS O. M MC FILE NUMBER: DATE OF ISSUE: 02/99 REVISION: D, 01/05

WARNING CLASSIC BLAST MACHINE WITH PNEUMATIC TLR REMOTE CONTROLS O. M MC FILE NUMBER: DATE OF ISSUE: 02/99 REVISION: D, 01/05 CLASSIC BLAST MACHINE WITH PNEUMATIC TLR REMOTE CONTROLS O. M. 22501 MC FILE NUMBER: 2072-0299 DATE OF ISSUE: 02/99 REVISION: D, 01/05 2005 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 63090

More information

WARNING TLR 100/300 SERIES PNEUMATIC REMOTE CONTROLS O. M

WARNING TLR 100/300 SERIES PNEUMATIC REMOTE CONTROLS O. M TLR 100/300 SERIES PNEUMATIC REMOTE CONTROLS O. M. 22428 MC FILE NUMBER: 2068-1298 DATE OF ISSUE: 12/98 REVISION: B, 10/09 2009 CLEMCO INDUSTRIES CORP. ONE CABLE CAR DR. WASHINGTON, MO 63090 Phone (636)

More information

WARNING POOL PAL 1 CU. FT. CAPACITY BLAST MACHINE O. M

WARNING POOL PAL 1 CU. FT. CAPACITY BLAST MACHINE O. M POOL PAL 1 CU. FT. CAPACITY BLAST MACHINE O. M. 24813 MC FILE NUMBER: 2314-0406 DATE OF ISSUE: 04/06 REVISION: B, 08/08 Do not proceed with these instructions* until you have READ the orange cover of this

More information

WARNING. Electronic files include a Preface containing the same important information as the orange cover.

WARNING. Electronic files include a Preface containing the same important information as the orange cover. CONTRACTOR SERIES 2 CU. FT. BLAST MACHINE WITH MILLENNIUM PNEUMATIC PRESSURE RELEASE REMOTE CONTROLS O. M. 21939 DATE OF ISSUE: 04/98 REVISION: G, 02/17 2017 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington,

More information

WARNING WETBLAST FLEX TM WATER-INJECTION ABRASIVE-BLAST SYSTEM

WARNING WETBLAST FLEX TM WATER-INJECTION ABRASIVE-BLAST SYSTEM WETBLAST FLEX TM WATER-INJECTION ABRASIVE-BLAST SYSTEM WITH MILLENNIUM ACS PNEUMATIC REMOTE CONTROLS O. M. 28452 DATE OF ISSUE: 04/15 REVISION: B 03/17 2017 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington,

More information

WARNING CLASSIC BLAST MACHINE 2 CU. FT. TO 20 CU. FT. CAPACITY WITH MANUAL CONTROLS O. M

WARNING CLASSIC BLAST MACHINE 2 CU. FT. TO 20 CU. FT. CAPACITY WITH MANUAL CONTROLS O. M CLASSIC BLAST MACHINE 2 CU. FT. TO 20 CU. FT. CAPACITY WITH MANUAL CONTROLS O. M. 06160 DATE OF ISSUE: 06/01/73 REVISION: N, 02/17 2017 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 63090 Phone

More information

WARNING HOLLO-BLAST. Electronic files include a Preface containing the same important information as the orange cover.

WARNING HOLLO-BLAST. Electronic files include a Preface containing the same important information as the orange cover. HOLLO-BLAST INTERNAL-PIPE BLAST TOOL O. M. 06158 MC FILE NUMBER: 140-0777 DATE OF ISSUE: August 1977 REVISION: F, 04/14 WARNING 2014 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 63090 Phone

More information

PNEUMATIC ABRASIVE CONVEYORS MODELS 16-PAC, 24-PAC, 30-PAC AND 36-PAC O.M MC FILE NUMBER: DATE OF ISSUE: 2/15/78 REVISION: C, 02/92

PNEUMATIC ABRASIVE CONVEYORS MODELS 16-PAC, 24-PAC, 30-PAC AND 36-PAC O.M MC FILE NUMBER: DATE OF ISSUE: 2/15/78 REVISION: C, 02/92 PNEUMATIC ABRASIVE CONVEYORS MODELS 16-PAC, 24-PAC, 30-PAC AND 36-PAC O.M. 04117 MC FILE NUMBER: 145-1177 DATE OF ISSUE: 2/15/78 REVISION: C, 02/92 NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS AND THIS

More information

WARNING BIG CLEM BULK BLAST MACHINES O. M

WARNING BIG CLEM BULK BLAST MACHINES O. M BIG CLEM BULK BLAST MACHINES O. M. 05110 DATE OF ISSUE: 05/71 REVISION: J, 07/15 2015 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 63090 Phone (636) 239-4300 Fax (800) 726-7559 Email: info@clemcoindustries.com

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM BP50 3 BLAST POT Manual Number: ZVP PC 0156 00 SECTION 1. GENERAL INFORMATION 2. INITIAL SETUP INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE 5. TROUBLE SHOOTING

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM BP110 3 BLAST POT Manual Number: ZVP PC 0155 00 SECTION 1. GENERAL INFORMATION 2. INITIAL SETUP INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE 5. TROUBLE SHOOTING

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM BP600 3 BLAST POT Manual Number: ZVP PC 0154 00 SECTION 1. GENERAL INFORMATION 2. INITIAL SETUP INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE 5. TROUBLE SHOOTING

More information

RPC-2 REVERSE PULSE DUST COLLECTOR

RPC-2 REVERSE PULSE DUST COLLECTOR RPC-2 REVERSE PULSE DUST COLLECTOR Clemco Industries Corp. One Cable Car Drive Washington, MO 63090 Phone: (636) 239-4300 Fax: (800) 726-7559 Email: info@clemcoindustries.com NOTICE TO PURCHASERS AND USERS

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM BP300-1 BLAST POT Manual Number: ZVP-PC-PB-0014 SECTION 1. GENERAL INFORMATION 2. INITIAL SETUP INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE 5. TROUBLE SHOOTING

More information

Classic Clemco Tough, Reliable, Quality Blast Machines

Classic Clemco Tough, Reliable, Quality Blast Machines Classic Clemco Tough, Reliable, Quality Blast Machines Semi-elliptical head for larger storage of abrasive. Urethane-coated pop-up valve with external sleeve for long life and fast pressurization. Large

More information

INTERNAL PIPE CLEANING TOOL

INTERNAL PIPE CLEANING TOOL INTERNAL PIPE CLEANING TOOL OPERATION & MAINTENANCE MANUAL Manual # Twister1512 Contents Page Important Notice 3 Introduction, Specifications & Air Requirements 4 Assembly Procedure 5 & 6 Safety 7 Set-up

More information

Initial Issue Date Revision Date: Revision No. Next Revision Date: Reliant Holdings Ltd Safety Management System. Issuing Dept: Safety

Initial Issue Date Revision Date: Revision No. Next Revision Date: Reliant Holdings Ltd Safety Management System. Issuing Dept: Safety BLASTING Preparation: Mgr SOP-1 Page: Page 1 of 10 Purpose The purpose of this program is to provide safe guidelines for the operation and maintenance of abrasive blasting equipment and their related components

More information

Product Brochure/Flyer

Product Brochure/Flyer Product Brochure/Flyer Copyright 2016 Burwell Technologies For more information: 1300 287 935 / mail@burwell.com.au / www.burwell.com.au Classic Clemco Tough, Reliable, Quality Blast Machines Semi-elliptical

More information

Hydraulic Long Jacks

Hydraulic Long Jacks Operating Instructions & Parts Manual Hydraulic Long Jacks Model 44915 44930 44940 44980 44981C (Air option) Capacity 1-1/2 Ton 3 Ton 4 Ton 8 Ton 8 Ton Models 44915, 44930, 44940 & 44980 Model 44981C U.S.

More information

Hydraulic Truck Jack

Hydraulic Truck Jack Operating Instructions & Parts Manual Hydraulic Truck Jack Model Capacity 23221C 22 Ton 23222C (Low Profile) 22 Ton 23301 30 Ton Models 23221C & 23222C Model 23301! U.S. Patent No's. 5,341,723 & 5,94,912

More information

ABSC-1028 Blast Machine - 18 ltr.

ABSC-1028 Blast Machine - 18 ltr. INSTRUCTION MANUAL Rev. A - Jan 2016 ABSC-1028 Blast Machine - 18 ltr. Surface Treatment Solutions Manufactured by: Airblast B.V. P.O. Box 1075 1700 BB Heerhugowaard The Netherlands Tel. : + 31 72 5718002

More information

Heavy Duty Engine Cranes

Heavy Duty Engine Cranes Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number Atd-7484 Atd-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model Atd-7484 Model Atd-7485 Atd Tools Inc. 160 Enterprise Drive, Wentzville,

More information

SB20G. Large Pressurized Abrasive Blaster Assembly & Operating Instructions

SB20G. Large Pressurized Abrasive Blaster Assembly & Operating Instructions SB20G Large Pressurized Abrasive Blaster Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides

More information

Hydraulic Transmission Jack, Telescopic

Hydraulic Transmission Jack, Telescopic Operating Instructions & Parts Manual Hydraulic Transmission Jack, Telescopic Model 4000 400 (Air Operated) Capacity 000 lbs. 000 lbs. Model 4000 Model 400 U.S. Patent No. 6,02,377! This is the safety

More information

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings -

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings - Instructions Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. 311082D Pressure Roller with 24-inch Fixed Extension - For application of architectural

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM AURORA LED HELMET & HOSE MOUNT KITS Manual Number: ZVP PC 0034 01 SECTION 1. GENERAL INFORMATION 2. INTRODUCTION 3. INSTALLATION 4. OPERATING INSTRUCTIONS 5. MAINTENANCE

More information

110 Volt/12 Volt Portable Inflator

110 Volt/12 Volt Portable Inflator 110 Volt/12 Volt Portable Inflator Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM CS37 SUCTION BLAST CABINET Manual Number: ZVP PC 0069 00 SECTION 1. GENERAL INFORMATION 2. ASSEMBLY & INSTALLATION INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE

More information

SBCNNS. Abrasive Blast Cabinet Assembly & Operating Instructions

SBCNNS. Abrasive Blast Cabinet Assembly & Operating Instructions SBCNNS Abrasive Blast Cabinet Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

Air-Operated Waste Oil Drainer

Air-Operated Waste Oil Drainer Air-Operated Waste Oil Drainer 20-Gallon Tank Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other

More information

ABSC-2452 Blast Machine ltr.

ABSC-2452 Blast Machine ltr. INSTRUCTION MANUAL Rev. A - Jan 2016 ABSC-2452 Blast Machine - 200 ltr. Surface Treatment Solutions Manufactured by: Airblast B.V. P.O. Box 1075 1700 BB Heerhugowaard The Netherlands Tel. : + 31 72 5718002

More information

Air Actuated Hydraulic Bottle Jacks

Air Actuated Hydraulic Bottle Jacks Air Actuated Hydraulic Bottle Jacks Operating Instructions & Parts Manual Model Number Atd-7412 Atd-7420 Capacity 12 Ton 20 Ton Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China

More information

Long Chassis Hydraulic Service Jacks

Long Chassis Hydraulic Service Jacks Model BH6011 Long Chassis Hydraulic Service Jacks Operating Instructions and Parts Manual Capacity 10 Ton Model BH6011 U.S. Patent No's. 5,946,912 5,341,723! This is the safety alert symbol. It is used

More information

OPERATOR S MANUAL BLASTMASTER 6.5 CU. FT. HP-SERIES ABRASIVE BLASTING POT

OPERATOR S MANUAL BLASTMASTER 6.5 CU. FT. HP-SERIES ABRASIVE BLASTING POT OPERATOR S MANUAL BLASTMASTER 6.5 CU. FT. HP-SERIES ABRASIVE BLASTING POT Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment.

More information

The information in this instruction manual is subject to modifications without prior notice and is the exclusive property of Zorzini.

The information in this instruction manual is subject to modifications without prior notice and is the exclusive property of Zorzini. Dear Customer, Thank you for choosing a Zorzini S.p.A. product. Zorzini manway doors and manhole covers 1 are designed and manufactured according to the highest standards in regards safety, functionality

More information

Operating Instructions & Parts Manual. Air/Manual Hydraulic Bottle Jacks

Operating Instructions & Parts Manual. Air/Manual Hydraulic Bottle Jacks J18124-M1_032015 Operating Instructions & Parts Manual Air/Manual Hydraulic Bottle Jacks Model J18124 J18204 Capacity 12 Ton 20 Ton U.S. Patent Nos. 6,012,377-5,946,912! This is the safety alert symbol.

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

12 Volt Heavy-Duty Air Inflator

12 Volt Heavy-Duty Air Inflator 12 Volt Heavy-Duty Air Inflator Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

Lubricator Gun: 10,000 psi (700 bar) Maximum Delivery Pressure when disconnected from Dispenser

Lubricator Gun: 10,000 psi (700 bar) Maximum Delivery Pressure when disconnected from Dispenser INSTRUCTIONS-PARTS LIST 30 455 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supercedes B Hand-Operated Portable Grease Dispenser Buckshot Luber

More information

OPERATOR S MANUAL BLASTMASTER 130E REMOTE CONTROL SYSTEM

OPERATOR S MANUAL BLASTMASTER 130E REMOTE CONTROL SYSTEM OPERATOR S MANUAL BLASTMASTER 30E REMOTE CONTROL SYSTEM Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If the user and/

More information

APCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES

APCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES APCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES Instruction D12043 June 2016 DeZURIK Instructions These instructions provide installation, operation and maintenance information for APCO CRF-100A Rubber

More information

SPIN-KOTE INTERNAL PIPE COATING TOOLS

SPIN-KOTE INTERNAL PIPE COATING TOOLS SPIN-KOTE Clemco Industries Corp. One Cable Car Drive Washington, MO 63090 Phone: (636) 239-4300 Fax: (800) 26-559 Email: info@clemcoindustries.com www.clemcoindustries.com NOTICE TO PURCHASERS AND USERS

More information

D Instructions/Parts. Siphon Feed Detail Spray Gun D

D Instructions/Parts. Siphon Feed Detail Spray Gun D Instructions/Parts D-5-55 Siphon Feed Detail Spray Gun FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309991D Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

OPERATOR S MANUAL BLASTMASTER 155E AND 156E REMOTE CONTROL SWITCHES

OPERATOR S MANUAL BLASTMASTER 155E AND 156E REMOTE CONTROL SWITCHES OPERATOR S MANUAL BLASTMASTER 155E AND 156E REMOTE CONTROL SWITCHES Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If

More information

User s Manual. 3.5 & 6.5 Cu Ft - EPH / EPR SERIES BLASTERS. Read Manual. Manual P/N: PB-MAE001

User s Manual. 3.5 & 6.5 Cu Ft - EPH / EPR SERIES BLASTERS. Read Manual. Manual P/N: PB-MAE001 User s Manual 3.5 & 6.5 Cu Ft - EPH / EPR SERIES BLASTERS These products and equipment are not under any circumstances to be used with sand or silica products of any type and use of such materials will

More information

Heavy Duty Bottle Jacks

Heavy Duty Bottle Jacks Heavy Duty Bottle Jacks Models: 10300 & 10500 10300 10500! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol

More information

PRODUCT OPERATING MANUAL

PRODUCT OPERATING MANUAL PRODUCT OPERATING MANUAL PANBLAST TM BP600 1 BLAST POT Manual Number: ZVP PC 0157 00 SECTION 1. GENERAL INFORMATION 2. INITIAL SETUP INSTRUCTIONS 3. OPERATING INSTRUCTIONS 4. MAINTENANCE 5. TROUBLE SHOOTING

More information

Customer Support

Customer Support Portable auxiliary air tanks owner's Manual aux05 aux05a aux10 WWW.CALIFORNIAAIRTOOLS.COM Customer Support 1-866-409-4581 TAbLe OF CONTeNTS INTROduCTION IntroductIon Important Safety InStructIonS components

More information

Low Profile Service Jack

Low Profile Service Jack Low Profile Service Jack Model GMG29031 Capacity 3 Ton U.S. Patent No. 6,199,379! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages

More information

Heavy Duty Engine Cranes

Heavy Duty Engine Cranes Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number ATD-7484 ATD-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model ATD-7484 Model ATD-7485 WARNING: This product may contain chemicals,

More information

T1-Titanium Non-HVLP Spray Gun

T1-Titanium Non-HVLP Spray Gun T1-Titanium Non-HVLP Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS 12 Volt High-V Volume Air Inflator Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND A OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

Clemco has earned its reputation for quality and customer support over six decades of service to industry.

Clemco has earned its reputation for quality and customer support over six decades of service to industry. Clemco has earned its reputation for quality and customer support over six decades of service to industry. ISO 9001 Certified Clemco Wetblast Systems Help Contractors Minimize Job Site Blast Dust The Wetblast

More information

MACHINES / RECLAIMS WITH DUST BAG

MACHINES / RECLAIMS WITH DUST BAG WARNING SET-UP INSTRUCTIONS MACHINES / RECLAIMS WITH DUST BAG *** READ BEFORE OPERATING EQUIPMENT *** 1. Remove plastic from machine. 2. Remove lag bolts from each of the four legs, then remove machine

More information

OPERATOR S MANUAL BLASTMASTER REGULATOR JR. ABRASIVE METERING VALVE

OPERATOR S MANUAL BLASTMASTER REGULATOR JR. ABRASIVE METERING VALVE OPERATOR S MANUAL BLASTMASTER REGULATOR JR. ABRASIVE METERING VALVE Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If

More information

TONS. Before each shift: Before operating: Before initial operation of hoist:

TONS. Before each shift: Before operating: Before initial operation of hoist: LEVER HOIST 0.25 9 TONS Manual Notice It is the responsibility of the owner/user to install, inspect, test, maintain, and operate these lever hoists in accordance with ASME B30.21, Safety Standard for

More information

OPERATOR S MANUAL BARRICADE 286 AIRLINE FILTERS

OPERATOR S MANUAL BARRICADE 286 AIRLINE FILTERS OPERATOR S MANUAL BARRICADE 286 AIRLINE FILTERS Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If the user and/ or assistants

More information

DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR

DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR OPERATION MANUAL DUAL PURPOSE DIAGNOSTIC LEAK DETECTOR P/N 95-030 NIS -800-662-200 nissantechmate.com CONTENTS Specifications / Warranty... Functions...2-3 Accessories... 4 Set-Up... 5 Adaptor Installation...

More information

Hydraulic Wheel Dolly

Hydraulic Wheel Dolly Hydraulic Wheel Dolly Operating Instructions & Parts Manual Model Number HW93766 Capacity 3/4 Ton Made in the U.S.A. This is the safety alert symbol. It is used to alert you to potential personal injury

More information

Gauge Adapter Instruction Manual

Gauge Adapter Instruction Manual Instruction Manual MODELS: CF3812, CF3812E, CF3814 & CF4514 CF3812-M1_092017! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that

More information

LUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type

LUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type INSTRUCTIONS-PARTS LIST 306 460 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. E Supercedes D Detachable-type LUBRICATOR GUN 10,000 psi (700 bar)

More information

Viscount I Hydraulic Motor and Displacement Pump

Viscount I Hydraulic Motor and Displacement Pump INSTRUCTIONS-PARTS LIST 308 674 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supersedes Rev. B Viscount I Hydraulic Motor and Displacement Pump

More information

APCO ASR-400/450 SEWAGE AIR RELEASE VALVES

APCO ASR-400/450 SEWAGE AIR RELEASE VALVES APCO ASR-400/450 SEWAGE AIR RELEASE VALVES Instruction D12005 December 2012 Instructions These instructions provide installation, operation and maintenance information for the APCO ASR- 400/450 Sewage

More information

OPERATOR S MANUAL BLASTMASTER 150P REMOTE CONTROL SWITCH

OPERATOR S MANUAL BLASTMASTER 150P REMOTE CONTROL SWITCH OPERATOR S MANUAL BLASTMASTER 150P REMOTE CONTROL SWITCH Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If the user and/

More information

Manifold w/ Needle Valve Instruction Manual

Manifold w/ Needle Valve Instruction Manual MODELS: MFC2 & MFC4 Manifold w/ Needle Valve Instruction Manual SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 - Fax: 816-448-2142 E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

More information

Pro Shot Grease Dispense Valve

Pro Shot Grease Dispense Valve Instructions Parts List Pro Shot Grease Dispense Valve 309032J For high pressure grease dispense. 8000 psi (55 MPa, 552 bar) Maximum Working Pressure Model No. 242055, Series B, 1/4 npt Fluid Inlet Model

More information

DeZURIK 2 20" BOS BUTTERFLY VALVES

DeZURIK 2 20 BOS BUTTERFLY VALVES 2 20" BOS BUTTERFLY VALVES Instruction D10459 October 2013 2-20 BOS Butterfly Valves Instructions These instructions provide information about BOS Butterfly Valves. They are for use by personnel who are

More information

Mini Jacks Instruction Manual

Mini Jacks Instruction Manual J11050-M0_062017 Instruction Manual MODELS: J11050, J11055-5 Ton Capacity J11100-10 Ton Capacity J11200-20 Ton Capacity This is the safety alert symbol. It is used to alert you to potential personal injury

More information

Spray Nozzle Adapters

Spray Nozzle Adapters INSTRUCTIONS-PARTS LIST 306 788 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. G Supersedes Rev. F DIRECTIONAL

More information

Operating Instructions & Parts Manual

Operating Instructions & Parts Manual Aluminum / Steel Hybrid Service Jack Operating Instructions & Parts Manual Model 26017 26028 26033 Capacity 1.5 Ton 2.5 Ton 3 Ton! This is the safety alert symbol. It is used to alert you to potential

More information

810201,810202,810203,810204

810201,810202,810203,810204 810201,810202,810203,810204 IP02 SERIES 2:1 RATIO TRANSFER PUMP OPERATIONING MANUAL WITH PARTS IDENTIFICATION IPM, INC. Manufactured by International Pump Manufacturing, Inc. IP02 series 2:1 RATIO TRANSFER

More information

OPERATOR S MANUAL BLASTMASTER 60 CU. FT. ABRASIVE BLASTING POTS

OPERATOR S MANUAL BLASTMASTER 60 CU. FT. ABRASIVE BLASTING POTS OPERATOR S MANUAL BLASTMASTER 60 CU. FT. ABRASIVE BLASTING POTS Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If the

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.1 LAST EDITED 7.25.14 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of

More information

Low Profile Service Jack Jack Stand Combo

Low Profile Service Jack Jack Stand Combo Low Profile Service Jack Jack Stand Combo Jack Stands Low Profile Service Jack U.S. Patent No. 6,199,379! This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

More information

CRD600 Automatic Fitting Inserter

CRD600 Automatic Fitting Inserter CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.3 LAST EDITED 12.07.2018 cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents. 2 1.0 General Product & Safety Information...3

More information

PENBERTHY MODELS GL AND GH GAS OPERATED JET PUMPS INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

PENBERTHY MODELS GL AND GH GAS OPERATED JET PUMPS INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Before installation, these instructions must be read carefully and understood. PRODUCT WARRANTY Emerson warrants its Penberthy products as designed and manufactured to be free of defects in the material

More information

40000 and PRESSURE BLASTER with Deadman Control System

40000 and PRESSURE BLASTER with Deadman Control System 40000 and 40002 PRESSURE BLASTER with Deadman Control System OPERATION GUIDE Rev. 9/8/15 DIVISION OF S&H INDUSTRIES 5200 Richmond Road Cleveland, OH 44146 Phone 216-831-0550 Toll Free 800-253-9726 Fax

More information

Heavy-Duty Welding Fabrication Table

Heavy-Duty Welding Fabrication Table Heavy-Duty Welding Fabrication Table with Fix-Up Kit Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and

More information

Operating Instructions & Parts Manual

Operating Instructions & Parts Manual Swift Lift Hydraulic Service Jack Operating Instructions & Parts Manual Model Number ATD7341 Capacity 3-1/2 Ton U.S. Patent No's. 5,946,912 6,199,379! This is the safety alert symbol. It is used to alert

More information

Clemco Wetblast Systems Help Contractors Minimize Job Site Blast Dust. The Wetblast FLEX TM

Clemco Wetblast Systems Help Contractors Minimize Job Site Blast Dust. The Wetblast FLEX TM Clemco has earned its reputation for quality and customer support over six decades of service to industry. Committed to extraordinary products, technical support, and service. ISO 9001 Certified Clemco

More information

CRD610 Automatic Fitting Inserter

CRD610 Automatic Fitting Inserter CRD610 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 1.2 LAST EDITED 12.12.2018 cleanroomdevices.com 1 Table of Contents Title Page. 1 Table of Contents...2 1.0 General Product & Safety Information....3

More information

OPERATOR S MANUAL BLASTMASTER 750 CFM AIR DRYER

OPERATOR S MANUAL BLASTMASTER 750 CFM AIR DRYER OPERATOR S MANUAL BLASTMASTER 750 CFM AIR DRYER Before using this equipment, read, understand and follow all instructions in the Operator s Manuals provided with this equipment. If the user and/ or assistants

More information

18 KG MOBILE SODA BLASTING UNIT

18 KG MOBILE SODA BLASTING UNIT OWNER S MANUAL PRODUCT CODE: 3043 18 KG MOBILE SODA BLASTING UNIT Working Air Hose Tank Volume Overall Dimensions Pressure Consumption Length 18KG 35 90psi 6-12CFM 2400mm 460 x 305 x 660 Made in China

More information

Fast Lift Service Jack, Low Profile

Fast Lift Service Jack, Low Profile Blackhawk Automotive is a Licensed Trade Mark Made by SFA Companies, Kansas City, MO Fast Lift Service Jack, Low Profile Operating Instructions & Parts Manual Model BH6023B Capacity 2 Ton! U.S. Patent

More information

1. Contents 1. CONTENTS INTRODUCTION SAFETY WARNINGS POWER TILT STANDARD OPERATING INSTRUCTIONS... 5.

1. Contents 1. CONTENTS INTRODUCTION SAFETY WARNINGS POWER TILT STANDARD OPERATING INSTRUCTIONS... 5. 1. Contents 1. CONTENTS..... 2. INTRODUCTION..... 3. SAFETY WARNINGS..... 4. POWER TILT STANDARD OPERATING INSTRUCTIONS....... 5. POWER SEAT LIFT STANDARD OPERATING INSTRUCTIONS...... 6. POWER TILT / SEAT

More information

DeZURIK AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators

DeZURIK AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators Instructions D11033 August 2013 Instructions These instructions provide information about AFR3 Filter Regulators. They are for use by personnel

More information

MagicLift Hydraulic Service Jack Model (w/one piece handle) (w/one piece handle)

MagicLift Hydraulic Service Jack Model (w/one piece handle) (w/one piece handle) Operating Instructions & Parts Manual MagicLift Hydraulic Service Jack Model 27025 27026 (w/one piece handle) 27035 27036 (w/one piece handle) Capacity 2-1/2 Ton 2-1/2 Ton 3-1/2 Ton 3-1/2 Ton Model 27025

More information

18 GAUGE FLOORING STAPLER. Models: /13

18 GAUGE FLOORING STAPLER. Models: /13 18 GAUGE FLOORING STAPLER Models: 7560 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

Propane torch. Model Assembly And Operation Instructions

Propane torch. Model Assembly And Operation Instructions Propane torch Model 39953 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA

More information

SPECIFICATIONS Horsepower: 1.5 HP Running Maximum PSI: 125 PSI Tank Capacity: 15 Gallons CFM: 6 40 PSI 5 90 PSI

SPECIFICATIONS Horsepower: 1.5 HP Running Maximum PSI: 125 PSI Tank Capacity: 15 Gallons CFM: 6 40 PSI 5 90 PSI 15 GALLON AIR COMPRESSOR Model: 7678 DO NOT RETURN TO STORE Please call 800-348-5004 for parts and service CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials

More information

Owner s Manual & Safety Instructions

Owner s Manual & Safety Instructions Owner s Manual & Safety Instructions Save Save This This Manual Keep Keep this this manual manual for for the the safety safety warnings warnings and and precautions, assembly, assembly, operating, inspection,

More information

2-Pack Indoor/Outdoor Simulated Security Cameras. Owner s Manual

2-Pack Indoor/Outdoor Simulated Security Cameras. Owner s Manual 2-Pack Indoor/Outdoor Simulated Security Cameras Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other

More information

Operating Instructions & Parts Manual

Operating Instructions & Parts Manual Hydraulic Air/Manual Bottle Jacks Operating Instructions & Parts Manual Model Number ATD-74 ATD-74 Capacity Ton 0 Ton! U.S. Patent No.'s. 5,34,73-5,946,9 This is the safety alert symbol. It is used to

More information

MG12K24T60V4 Mechanical Grapple

MG12K24T60V4 Mechanical Grapple 170 State Route 271 Attachment Solutions MG12K24T60V4 Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information....

More information

2-Pack Indoor Simulated Dome Security Cameras

2-Pack Indoor Simulated Dome Security Cameras 2-Pack Indoor Simulated Dome Security Cameras Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other

More information

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance Troubleshooting

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance Troubleshooting Model 3182 2,500 Lbs Power Train Table/Lift OWNER'S MANUAL CONTENTS: Page 1 Page 2-3 Page 3 Page 4 Page 5 Page 5 Page 6 Page 7 Page 8 Specifications Warning Information Setup Operating Instructions Preventative

More information

QUICK START GUIDE OWNER S MANUAL AL50 SERIES SAND FILTRATION TECHNOLOGY PLEASE CALL DO NOT RETURN TO STORE

QUICK START GUIDE OWNER S MANUAL AL50 SERIES SAND FILTRATION TECHNOLOGY PLEASE CALL DO NOT RETURN TO STORE QUICK START GUIDE OWNER S MANUAL SAFETY, INSTALLATION, OPERATION & PARTS AL50 SERIES SAND FILTRATION TECHNOLOGY PLEASE CALL 877-278-2797 DO NOT RETURN TO STORE! WARNING This equipment must be installed

More information

Voltmaster Centrifugal Trash Pumps

Voltmaster Centrifugal Trash Pumps Voltmaster Centrifugal Trash Pumps Model TSP2, TSP3 and TSP4 Owner s Manual February 2011 Table of Contents 1 Introduction............................ 1 1.1 Read before using..................... 1 1.2

More information

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance and Troubleshooting

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance and Troubleshooting Model 3322 22 Ton Air/Hydraulic Truck Axle Jack OWNER'S MANUAL CONTENTS: Page 1 Page 2 Page 3-4 Page 4-5 Page 5 Page 6 Page 7 Page 8 Specifications Warning Information Assembly Operating Instructions Preventative

More information