How to connect a D-R-PP-Filter-Unit with a Haase VSLxx

Size: px

Start display at page:

Download "How to connect a D-R-PP-Filter-Unit with a Haase VSLxx"

Roberta Marsh
6 years ago
Views:

RUJA AUTOMATION June 2009 How to connect a D-R-PP-Filter-Unit

Connection nipple 1 x Connection piece IN Dev tray Connection

piece OUT Wash tray Connection piece IN Wash tray 2- Tools

1 RUJA AUTOMATION June 2009 How to connect a D-R-PP-Filter-Unit with a Haase VSLxx 1- Contents: 15 x Clamp 4 x Valve 5 x Connection nipple 1 x Connection piece IN Dev tray Connection piece OUT Dev tray 10m Hose dia 20 mm 4x Wheels 1 x Connection piece OUT Wash tray Connection piece IN Wash tray 2- Tools needed: Screw driver Knife Drilling machine Drill dia 26 mm PVC glue (Tangit) & Teflon 3- Unpacking: 3.1 Content: D-R-PP-Filter Unit Filter Bags Installation Kit Page 1 of 11 D-R-PP-Filter installation guide VSL

2 3.1 Preparation: Unscrew the 4 fixation bolts. Install the 4 wheels. In case of external buzzer, install the Tower light into the vertical position. Page 2 of 11 D-R PP Filter installation guide VSL

3 Remove the ph probe from the circulation tube. Unpack the probe, take care of O rings and fluid container. Remove the fluid container and put the PVC plug into position. Glide the 2 O rings (first the large and than the smaller one). Page 3 of 11 D-R PP Filter installation guide VSL

Carefully tighten the PVC plug to prevent leakages.

4 Install the ph probe in the lower section of the Filtration Unit. This PVC T part is in the return flow direction of the Water Filter. Carefully tighten the PVC plug to prevent leakages. Glue the 5 PVC pipe connection nipples. Use Tangit PVC glue to fix The 5 nipples. Page 4 of 11 D-R PP Filter installation guide VSL

3.2 Connection: Prepare the hoses and valves Length of the hoses = 250 mm!

Remove the burrs on the drilled hole 40mm 140mm 165mm Drill a hole dia 26 mm thru the

5 3.2 Connection: Prepare the hoses and valves Length of the hoses = 250 mm! Do not yet connect them to the filter unit Drill a hole dia 26 mm thru the wall of the VSL Dev tank (left side). Position 40 mm below the metal frame and 140 mm left of the metal frame. Remove the burrs on the drilled hole 40mm 140mm 165mm Drill a hole dia 26 mm thru the wall of the VSL Dev tank (bottom part). Position 120 mm left from the drain hole. Remove the burrs on the drilled hole 80mm Page 5 of 11 D-R PP Filter installation guide VSL

6 Put the rubber sealing on the washtank connection piece Mount the connection piece into the wash tank, rubber sealing inner side Screw the nut on the connection piece, reinforcement ring against the Dev tank wall Put Teflon on the threaded part Screw the elbow onto the connection, angle of 45 towards the developer section Install the nipple on the hose Glue the PVC nipple into the elbow Screw the connection piece in the bottom part of the Dev tank Use the Teflon to ensure a "leak proof" connection Page 6 of 11 D-R PP Filter installation guide VSL

On the inside of the wash tank position the elbow 45 towards the

Wash tray. Check for the optimal position.

7 On the inside of the wash tank position the elbow 45 towards the center of the Dev section Drill a hole dia 26 mm thru the wall of the VSL Wash tray (left side). Position 40 mm below the metal frame and In the center of the Wash tray. Check for the optimal position. Remove the burrs on the drilled hole There are two options for the OUT connection of the Wash tray. A hole in the bottom center of the tray or a T PVC connection piece in the Drain connection tube. Page 7 of 11 D-R PP Filter installation guide VSL

8 Connect the hoses with valves to the filter unit. There are 4 valves IN OUT Dev section and IN-OUT Wash section. The Drain has no extra valve. DRAIN Wash IN Wash OUT Dev OUT Dev IN Page 8 of 11 D-R PP Filter installation guide VSL

Software Installation: Copy the software file phcontroller.exe on your PC. Run this file and follow on screen instructions. It will install the necessary drivers and firmware on your PC.

9 4. Finalization: Clean the Dev & Wash tank and make sure that all PVC particles are removed Re-install the rollers, brushes and guide plates. Connect the Filter Unit to the socket in the electrical compartment of the Processor. The modification is now finished, for start up refer to the user manual. 5. Software Installation: Copy the software file phcontroller.exe on your PC. Run this file and follow on screen instructions. It will install the necessary drivers and firmware on your PC. Connect your PC with a USB cable to the Filter Unit and power up the system. Run the phcontroller_proj.exe file the actual firmware to control and update all parameters in the Filter Unit. Screen dump Page 9 of 11 D-R PP Filter installation guide VSL

6. Filter flow diagram: Valve 3 2 1 4 5 6 7 1 2 3 4 5

10 6. Filter flow diagram: Valve Page 10 of 11 D-R PP Filter installation guide VSL

11 7. Electrical Diagram: Page 11 of 11 D-R PP Filter installation guide VSL

RUJA AUTOMATION June User manual. D R PP Filter - Unit. Page 1 of 10 User manual D-R--P-Filter -Unit

RUJA AUTOMATION June User manual. D R PP Filter - Unit. Page 1 of 10 User manual D-R--P-Filter -Unit User manual D R PP Filter - Unit Page 1 of 10 User manual D-R--P-Filter -Unit 1. Technical specifications 2. Safety instructions 3. User section 4. Spare parts list 5. Ordering info Page 2 of 10 User manual