RTM3 OXYGEN-THERAPY FLOWMETERS WITH FLOATING BALL
|
|
|
- Jody Cain
- 6 years ago
- Views:
Transcription
1 RTM3 OXYGEN-THERAPY FLOWMETERS WITH FLOATING BALL English version 09/2015
2 RAIL MOUNTING SYSTEMS AFNOR rail mounting systems BS rail mounting systems (neutral DIN rail mounting systems US OHMEDA rail mounting systems NORDIC rail mounting systems UNI rail mounting systems Others standards available upon request. DISS rail mounting systems 2
3 DIRECT PROBES AFNOR direct probes BS direct probes CZECH direct probes DIN direct probes US OHMEDA direct probes NORDIC direct probes CARBUROS direct probes UNI direct probes DISS direct probes Others standards available upon request. 3
4 RTM3 The RTM3 flowmeter with floating ball is used to adjust and measure the flow of a gas that is to be delivered to patients through the respiratory tract. The RTM3 should be connected to a source of pressured gas on the wall either using a direct probe or a rail mounting system. It must be fitted at its outlet either with a humidifier/nebulizer or with an outlet tubing nipple. Main technical features: Medical device of glass lla. In compliance with the EN ISO 15002: 2008 standard. Inlet pressure : 4.5 bar + / _ 0.5 bar (O bar + / _ 0.5 bar (Air Flowmeter with compensated pressure ensuring perfect flowrate stability and accuracy. The scale working pressure is the same as the pressure of the network so that the scale is not affected by any counter-pressure. New type of "cartridge" knob, extremely reliable, easyto-clean and ensuring an optimized adjustment. Perfect tighness of the knob thanks to its polyamide seat. The knob was tested under pressurized working conditions during more than 10,000 cycles (which corresponds to 5 openings / closings every day during more than 5 years without showing any leakage after closing. This allows us to guarantee the closing of the knob during 5 years without any leakage. Monoblock scale cover made of polyamide for a higher sturdiness and a greater safety. The inopportune unscrewing of the monoblock scale cover is not possible. Patients have no acces to te scale. Expanded scale providing higher reading accuracy for low flowrates (only for 05 l/min and 15 l/min RTM3 flowmeters. Filter at the scale inlet protecting the device against any gas network impurities and thus ensuring the protection of both the patient and the flowmeter. Body made of nickel-plated brass, very strong. Flowmeter MRI compatible. Normative information (gas name, CE marking, signs related to the use of the devise are mentionned on a self-adhesive ring for a better reading and immediate identification of a TM device. The identification ring is protected against tarnishing and wear & tear thanks to the monoblock cover. A unit serial number is engraved on the body of each flowmeter ensuring its identification and traceability. 8 digits number indicating the manufacturing year and month as well as the unit serial number of the device. Many versions available: Available gases & flowrates: OXYGEN & MEDICAL : 1.5l/min, 5l/min, 15l/min, 30l/min CO 2 : 12l/min CARBOGEN: 15l/min Inlets: 12x100F - - 1/8NPT F - 3/8"BSP F. Outlets: 12x125 M - - 1/2" BS F -. Available configurations: Single, Twin and DUO. Available connections to the wall outlet: Direct probe or Rail mounting system. Standards: AFNOR (French Standard - BS (British Standard DIN (German Standard - US OHMEDA DIAMOND (American standard - NORDIC (Scandinavian Standard UNI (Italian Standard - DISS (American Standard. Weight (without direct probe: 275 g. Dimensions (without direct probe: Height 145 mm x width 35 mm x depth 70 mm. Use, cleaning and maintenance: The RTM3 flowmeter must be connected vertically. Then just open the knob and adjust the position of the floating ball according to the required flowrate (reading in the middle of the ball. Clean the outisde of the device with water and soap. Rinse and dry. If using disinfecting products please check their compatibility with plastics. Do not lay under water. Device to be serviced every 1 to 3 years according to intensive use, if any. Accessories: Tubing nipple (1 part or tubing nipple (2 parts Switch or Flow-Switch Humidifier: CCO model (250 ml or TMS model (500ml 4
5 R01 RTM3 O 2 15 l/min mounted with BS direct probe and 9/16" outlet tubing nipple R02 RTM3 O 2 05 l/min mounted with DIN direct probe and 250 ml CCO humidifier R03 RTM3 O 2 15 l/min mounted with DIN complete rail mounting system (neutral and 9/16" outlet tubing nipple R04 RTM3 O l/min mounted with NORDIC complete rail mounting system and 9/16" outlet tubing nipple 5
6 R05 RTM3 O 2 15 l/min mounted with UNI direct probe and 500 ml TMS humidifier R06 Twin RTM3 O l/min mounted with AFNOR direct probe and 12 x 125 outlet tubing nipples R07 RTM3 05 l/min mounted with BS direct probe and 1/2" BS outlet tubing nipple R08 RTM3 15 l/min mounted with AFNOR complete rail mounting system (with metal clamp 6
7 RTM3 DUO FLOWMETER Patented model Double outlet integrated in the body of the flowmeter: One horizontal outlet tubing nipple; One vertical central threaded outlet to connect a humidifier (outlet thread 12x125 M and available. Thanks to this DUO system there is no need to screw and unscrew the outlet tubing nipple or the humidifier. The saving of time is really appreciated compared to a standard flowmeter and the risk of losing the nipple is avoided. The user can choose between 3 positions and can switch from one position to another without removing the nipple or the humidifier. 1 st position: the gas flow is delivered through the nipple. 2 nd position: the gas flow is cut off. Parking position. 3 rd position: the gas flow goes through the vertical central outlet to which you can connect either a CCO humidifier (250 ml or a TMS humidifier (500 ml or any other model (single-use humidifier, nebulizer. Also available with a complete rail mounting system. R09 RTM3 DUO O 2 15 l/min with AFNOR direct probe To convert the standard RTM3 flowmeters into DUO flowmeters the solution is : TM FLOW-SWITCH OR SWITCH Flow-Switch: model with ring (R10 Switch: model with knob (R11 R11 Both Flow-Switch and Switch can be screwed onto any standard flowmeter. They enable you to deliver a gas flow either through the outlet tubing nipple or through a humidifier. Available with 12x125 or 9/16" threaded inlet and outlet. R10 7
8 AFNOR French Standard OXYGEN (O 2 MEDICAL 12 x 100 F Mounted with AFNOR direct probe Mounted with AFNOR complete rail mounting system (polycarbonate clamp Flowrates l/min 12x125M 12x125M 12x125M 12 x x125M 12 x 125 WITH FLOATING BALL Single Single Single Single Twin DUO X X X X X X X X X X X X X X X X X X X X BS British Standard WITH FLOATING BALL OXYGEN (O 2 MEDICAL Mounted with BS direct probe Mounted with BS complete rail mounting system (polycarbonate clamp Flowrates l/min 1/2" BS F Single Single Single Single Twin DUO X X X X X X X X X X X X 8 * Outlet tubing nipple in 2 parts, metal - Available upon request only. X Not available. Please contact us for other flowmeter configurations.
9 DIN German Standard OXYGEN (O 2 MEDICAL DIN ISO DIN NEUTRAL WITH FLOATING BALL Flowrates l/min Single Single Single Single Twin DUO X Mounted with DIN direct probe DIN ISO 9/16" X X X DIN NEUTRAL Mounted with DIN complete rail mounting system (polycarbonate clamp DIN ISO 9/16" X X X X DIN NEUTRAL X US OHMEDA American Standard OXYGEN (O 2 MEDICAL / ISO MEDICAL / ISO MEDICAL / US 1/8NPT F Mounted with US OHMEDA direct probe Mounted with US OHMEDA complete rail mounting system (polycarbonate clamp Flowrates l/min WITH FLOATING BALL Single Single Single Single Twin DUO X X X X X X X X X X X X 9 * Outlet tubing nipple in 2 parts, metal - Available upon request only. X Not available. Please contact us for other flowmeter configurations.
10 NORDIC Scandinavian Standard OXYGEN (O 2 MEDICAL Flowrates l/min WITH FLOATING BALL Single Single Single Single Twin DUO X /8NPT F X Mounted with NORDIC direct probe X X X X X Mounted with NORDIC complete rail mounting system (polycarbonate clamp X X X X UNI Italian Standard WITH FLOATING BALL OXYGEN (O 2 MEDICAL Flowrates l/min Single Single Single Single Twin DUO X X X Mounted with UNI direct probe X X X X X Mounted with UNI complete rail mounting system (polycarbonate clamp X X X X X X * Outlet tubing nipple in 2 parts, metal - Available upon request only. X Not available. Please contact us for other flowmeter configurations. 10
11 1 2 Reference Description Monobloc scale cover in polyamide COMPLETE SCALE O Complete scale 1.5 l/min (paediatric Complete scale 05 l/min 4.5 bar Complete scale 15 l/min 4.5 bar Complete scale 30 l/min 4.5 bar Complete scale 05 l/min 4.5 bar Complete scale 15 l/min 4.5 bar Complete scale 30 l/min 4.5 bar Gasket for scale bottom Gasket for scale cover Inlet adaptator 12 x 100F Inlet adaptator Inlet adaptator 1/8NPT F Inlet adaptator 3/8G BSP F Inlet gasket for flowmeter Inlet flowmeter filter BODY ONLY Body only 12x125 M Body only 12x125 M for paediatric 1.5l/min RTM3 Body only Body only for paediatric 1.5l/min RTM3 Body only Body only 1/2"BS F 1 COMPLETE KNOB O 2 complete knob Air complete knob 9A O 2 knob only, white O 2 knob only, black (Neutral Air knob only, black 2 9B Gasket for inlet adaptor 9C Knob axis gasket 9D Knob seat 3 4 9A 9B 9C 9D
12 OXYGEN-THERAPY FLOWMETERS WITH FLOATING BALL Distributed by 101, rue Vaillant Couturier B.P. 46 F NOISY-LE-SEC CEDEX France Tel: 33 ( Fax: 33 ( ( info@technologiemedicale.com 09/2015 Coordination : Serge Itzkowitch Création : Acantic Photographies : Frédéric Margaux. Also available
MEDICAL DEVICES BY GREGGERSEN
MEDICAL DEVICES BY GREGGERSEN CATALOG FLOWMETER there is no substitute CATALOG FLOWMETER Kolibri compact flowmeter PLUG-IN UNITS Medical, stop-adjustable compact flowmeter for oxygen and compressed air
U-CARE. OT / ICU Resuscitation / Suspended columns
U-CARE OT / ICU Resuscitation / Suspended columns FUNCTIONALITY The U-CARE suspended beam satisfies most of the requirements of healthcare professionals and offer comfort and safety when carrying biomedical
www.wefoundyourflowmeter.com For more information call 1. 866. 462. 6839 / 905. 764. 7736 Ohio Medical has found a flowmeter that won t be moved or lost. Introducing the new Tube Style Integrated Flowmeter
502 brass ball valve with ADA pneumatic actuator
502 brass ball valve with ADA pneumatic actuator MAIN CHARACTERISTICS The 502 valve is a brass ball valve dedicated to the automatic shut off of lines of standard fluids like water or air. With chromed
Vacuum Regulators and Accessories
Vacuum Regulators and Accessories Unique, Modular Design, Devices for Suction Needs Continuous PM3000, PM3100, PM3500 & PM3600 Vacuum Regulators Continuous-Intermittent PM3300 & PM3400 PM3100D PM3300DHV
Accurate measurement of compressed air consumption and detection of leaks. Measuring the individual consumption per customer / cost centre
Inline Flowmeter for compressed air and gases DN15 - DN50 / 16 bar The flow meter of the series, based on the measurement principle of thermal mass flow, is ideally suited for the measurement of flow of
BALL VALVE WITH ADA PNEUMATIC ACTUATOR
702-703 BALL VALVE WITH ADA PNEUMATIC ACTUATOR DESCRIPTION The 702-703 ball valves are dedicated to the automatic shut off of industrial fluid s lines. It is a 3 pieces full valve with internal screws
Servicing Instructions
Servicing Instructions Therapy Equipment Pipeline Suction Range Revision 5 : June 2013 CONTENTS Section No. 1 Record of Permanent Revisions 2 Pipeline Suction Product Information 3 Annual Function Test
Configurations: s.64. s.31. s.74 3 way. Flow: Mini 2 way Direct mount. Flow: Full. Flow: Standard 3 way. ISO 5211 F03 Flange
RUBINETTERIE UTENSILERIE BONOMI MEETING STANDARDS IS OUR STANDARD Configurations: 1 2 3 s.31 s.64 s.74 3 way Flow: Mini 2 way Direct mount Flow: Full 2 way ISO 5211 F03 Flange Flow: Standard 3 way ISO
HYDRA DUO. multi-stage self-cleaning filters
SELF-CLEANING FILTERS HYDRA DUO andtrio multi-stage self-cleaning filters Exclusive multi-stage filters with self-cleaning pre-filter, for dual and triple stage water filtration and treatment 169 multi-stage
COLLECTION JARS & LINERS SUCTION COLLECTION JARS SUCTION LINERS ACCESSORIES
COLLECTION JARS & SUCTION LINERS SUCTION ACCESSORIES English version 11/ 2010 TM COLLECTION JARS The collection jrs re used to collect liquids or mucus resulting from medicl suction. They cn e used in
CEGA FORANO BY GREGGERSEN
CEGA FORANO BY GREGGERSEN PRODUCT CATALOG FORANO Terminal Unit According to DIN EN ISO 9170-1 GENERAL According to national and international standards, The unit is used to withdraw compressed gases and
COLLECTION JARS & SUCTION LINERS SUCTION COLLECTION JARS SUCTION LINERS ACCESSORIES. English version 11/ 2 010
COLLECTION JARS & SUCTION LINERS SUCTION ACCESSORIES English version 11/ 2 010 TM COLLECTION JARS The collection jrs re used to collect liquids or mucus resulting from medicl suction. They cn e used in
Inline Flow meter for compressed air and gases DN15 (1/2 ) - DN80 (3 )
EE771/EE772 Inline Flow meter for compressed air and gases DN15 (1/2 ) - DN80 (3 ) The inline flow meter EE771/EE772, based on the measurement principle of thermal mass flow, is ideally suited for the
DECLARATION OF CONFORMITY FOR THE MEDICAL DEVICE FAMILY OUTLETS FOR COMPRESSED MEDICAL GASES AND VACUUM AND FOR ANAESTHETIC GAS SCAVENGING SYSTEMS
DECLARATION OF CONFORMITY FOR THE MEDICAL DEVICE FAMILY OUTLETS FOR COMPRESSED MEDICAL GASES AND VACUUM AND FOR ANAESTHETIC GAS SCAVENGING SYSTEMS whose codes are specified in the attachment, to the essential
THERAPY EQUIPMENT LTD
THERAPY EQUIPMENT LTD Manufacturers of Health Care Equipment QUALITY UK MANUFACTURER SINCE 1983 2 7701 - DIAMOND HIGH SUCTION CONTROLLER 0 9506 - DIAMOND RANGE AIR FLOWMETER & PROBE 1 4550 - RAIL MOUNTED
KDG/KDF - Flow Meter and Flow Switch
Integral Flow Control Valve Easy to Read Scale Brass, SS, or PVDF Process Connections Direct Reading Scales for Water and Air Compact Economical Design Optional Panel Mounting Kit Optional Flow Switch
BFS-10-O G1/4: BFS-10-O G1/2: BFS-10-O G1: Contact rating: BFS-10-O G1/4
Flow Switches Index: B / 923-1838 BFS-10-N / BFS-10-O for monitoring liquids, with or without optical display Features set point continuously adjustable rugged, low hysteresis, any mounting position, high
mass flowmeter for compressed air
mass flowmeter for compressed air VARIOMASS ECO pressure and temperature compensated easy and cost effective installation of the sensor no pressure loss caused by the sensor no moving parts, i.e. maintenance
FILTER HOUSINGS PLUS HOT 3P
FILTER HOUSINGS PLUS HOT 3P for cartridges SX and BX PLUS HOT 3P is a range of housings applicable for hot water with special FA-HOT wound polypropylene cartridges, with CPP polypropylene melt-blown cartridges
SUITABLE FOR. Wasserdampf. Steam EXAMPLES OF USE APPROVALS. Requirements PED 2014/68/EU. Classification society
Overflow and pressure control valves Series 618 6.4 618 Overflow and pressure control valves made of gunmetal, angle-type with threaded connections SUITABLE FOR Liquids neutral and non-neutral Air, gases
2-position electric actuators with Ball valves VBZ ½...11/4
4 831.2 & VBZ ½...11/4 2-position electric actuators with Ball valves VBZ ½ 11/4 90 angle - Unidirectional rotation VBZ ½ 11/4 Electric rotary actuators for two-port ball valves Operating voltage AC 230
715 XS BALL VALVE + ADA PNEUMATIC ACTUATOR
715 XS BALL VALVE + ADA PNEUMATIC ACTUATOR MAIN CHARACTERISTICS The 715 XS isolating valve is a two pieces ball valve for industrial applications with all compatible fluids. The body and the trim are full
Flow VA 500/ 520. Flow sensors for compressed air and gases incl. temperature measurement. Verbrauch.
VA 500/ 520 Flow sensors for compressed air and gases incl. temperature Verbrauch 79 What are the advantages of the flow measuring technology of CS Instruments? 1) Even under pressure, the ow sensor VA
Data sheet for MATRE BALANCED FOAM PROPORTIONERS
Data sheet for MATRE BALANCED FOAM PROPORTIONERS Datasheet for MATRE Balanced Foam Proportioners 1 Contents 2 General product information... 3 3 General product features:... 3 4 Flow range and interface
HLX771/772. Inline Flowmeter for compressed air and gases DN15 (1/2 ) - DN80 (3 ) Typical Applications
The inline flow meter, based on the measurement principle of thermal mass flow, is ideally suited for the measurement of flow in pipelines DN15 (1/2 ) up to DN80 (3 ). Measurement of for instance the usage
80% Max working pressure: Max working temperature: 70 C. Flow-meter regulation range: Flow meter-regulation range: ± 10%
Luxor s distribution manifolds are from brass bar CW617N. The manifolds are tooled and produced with fully automated machineries and tested when complete with their accessories to guarantee their absolute
Foaming of Lubricating Oils (manual)
Foaming of Lubricating Oils (manual) ASTM D 892, ASTM D 6082 sequence IV, ISO 6247, DIN 51566, IP 146, JIS K2518, BS 5092 (obs.) Product group(s): User group(s): Scope: Lubricant Testing Automotive, Engine
Configurations: s.64. s.31. s.74 3 way RUBINETTERIE UTENSILERIE BONOMI. Flow: Mini 2 way Direct mount. Flow: Full 2 way
RUBINETTERIE UTENSILERIE BONOMI Configurations: 1 2 3 s.31 s.64 s.74 3 way Flow: Mini 2 way Direct mount Flow: Full 2 way ISO 5211 F03 Flange Flow: Standard 3 way ISO 5211 F03 Flange Mini up to 3/4 Full
patented standards SAFETY QUICK COUPLINGS EXPERTISE AT THE SERVICE OF SAFETY AND PERFORMANCE General Catalogue a n d ot h e r p e n di n g
SAFETY QUICK COUPLINGS EXPERTISE AT THE SERVICE OF SAFETY AND PERFORMANCE PREVO S1 couplings represent the latest generation of pneumatic connection mechanisms. They provide a fully safe response to the
Connection Ports: 3/4 1 1/4 BSP (other thread options on request)
HYDRAULIC FILTRATION Medium pressure, in line spin-on filters Technical Information Pressure: Max working (acc. to NFPA T 3.10.17): FA-4-1x: 34,5 bar (500 psi) FA-4-21: 24 bar (348 psi) Burst (acc. to
A SURVEY OF OUR KNOW-HOW : PETROLEUM GLASSWARE VISCOMETER TUBES
N O R M A L A B A N A L I S A SURVEY OF OUR KNOW-HOW : PETROLEUM GLASSWARE VISCOMETER TUBES NORMALAB ANALIS FRANCE S.A. 14, rue des Lilas 76210 LINTOT - FRANCE Tel : (33) 02 35 38 59 59 Fax : (33) 02 35
Datasheet Rev.1 Feb 2014 High precision flowmeter
Datasheet Rev.1 Feb 2014 High precision flowmeter DeltaTMHP Warranty of high accuracy measurement Compliance with the requirements while limiting the measurement uncertainties to their minimum (ISO5167,
SPARE PARTS CATALOGUE SAFETY WELDING & CUTTING
SPARE PARTS CATALOGUE SAFETY WELDING & CUTTING Delivery within 24 hours from stock! (The Netherlands) Katje Welding bv, De Steven 4, NL-9206 AX Drachten, PO Box 5, NL-9200 AA Drachten, tel. +31-512-532829,
GALATEA. Dal 1901 COD
GALATEA COD. 9942027.08 REV.00 TAVOLA 1 Mod. MN - DE 1 5074423DL FRONT BASEMENT FRONTAL 2 5074424DL REAR BASEMENT FRONTAL 3 7817801 SCREW TPS M4X16 4 7816002 SCREW TCEI M4X12 5 5340500LL RIGHT-LEFT LATERAL
SRG LPG Liquid Service/Offtake Valve Type /
SRG LPG Liquid Service/Offtake Valve Type 480-426 / 480-427 Inlet Connection Outlet Connection Width across flats ¾ NPT 1 ¼ NPT M26x1,814 36 mm 46 mm Product Description: The SRG type 480 liquid service
Dry Pillar Hydrant Type ADR with pre-set break. Technical Bulletin. code. General description
Dry Pillar Hydrant Type ADR with pre-set break General description Type ADR with pre-set break off point and automatic shut-off in case of breakage to prevent water escape. Above ground section 360 rotational
WAYS BALL VALVES WITH ADA ACTUATOR
783-786 3-WAYS BALL VALVES WITH ADA ACTUATOR MAIN CHARACTERISTICS The three-ways flanged ball valve type 783-785 à brides is dedicated to the mixing or deviating functions in process of fluids. With full
Thermo Scientific Gilmont
Direct Reading Laboratory Flowmeters Instruments Wide selection of flow ranges measure air from 0.02 ml/min to 137 LPM or water from 0.0002 ml/min to 4.1 LPM Excellent chemical compatibility with glass
736XS-746 XS VALVE WITH AP PNEUMATIC ACTUATOR
736XS-746 XS VALVE WITH AP PNEUMATIC ACTUATOR VALVE FEATURES The 736 XS-746 XS is a 3 pieces full bore ball valve for industrial fluids, especially made to be easily actuated and to offer a good and long
Technical Datasheet. SP Terminal Units. Classification. Services. Terminal Block. Check Valve Assembly. Tailpipe Options
SP Terminal Units Pneumatech MGS East & Zeus SP terminal units provide a safe means of supplying medical equipment with medical gases from the central gas supply system. They are manufactured to accept
SELF-CLEANING FILTER
SELF-CLEANING FILTER CT0126.0_00 UK November 2008 PRODUCTION RANGE Connections Standard Mesh [μm] Size Code Kv [m³/h] THREADED FF UNI-EN-ISO 228 100 3/8 126.03.10 1,80 1/2 126.04.10 3,10 3/4 126.05.10
High-Tech Waterjet Cutting
6,200 bar High-Pressure Innovations STREAMLINE PRO-I ultra high-pressure pumps PRO series cutting heads AMS PRO abrasive management system PSC PRO installation parts High-Tech Waterjet Cutting About KMT
SUITABLE FOR EXAMPLES OF USE APPROVALS. Requirements PED 2014/68/EU
Overflow and pressure control valves Series 630 6.10 630 Overflow and pressure control valves made of gunmetal, straightway form with threaded connections externally adjustable SUITABLE FOR Liquids neutral
B21 Series BASOTROL Gas Valve
Installation Instructions B21 Issue Date September 19, 2017 Installation IMPORTANT: These instructions are intended as a guide for qualified personnel installing or servicing BASO Gas Products. Carefully
INSERTION flow sensor for continuous flow measurement
INSERTION flow sensor for continuous flow measurement Economic integration in pipe systems without any additional piping 3-wire frequency pulse version to directly interface with PLC s (both PNP and NPN)
Variable Area Flowmeters Ori-Flowrator TM Meters
Data Sheet (US) Variable Area Flowmeters Ori-Flowrator TM Meters 10B4000 Low installation cost Linear indication over 12-1/2 to 1 flow range Inexpensive method of measuring large flow rates in direct flow
LINED EQUIPMENT // Fort Vale Engineering Ltd CATALOGUE REVISION_
LINED EQUIPMENT // 3 45 Footvalve 4 to 3 Hydraulic Footvalve 25mm Ball Valve 50mm Ball Valve 80mm Ball Valve 3" Butterfly Valve MK3 65mm Flanged Relief Valve 80mm Flanged Vacuum Vent Valve Fort Vale Engineering
Connection Ports: 1/2 1 1/2 BSP (other thread options on request) aluminium alloy NBR (FKM on request)
HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working (acc. to NFPA T 3.1.5.1): F1-XD4/63/1: 1 bar (15 psi) F1-XD16/25/4: 8 bar (12 psi) Housing Burst (acc. to
Signet 2551 Magmeter Flow Sensor
Signet 2551 Magmeter Flow Sensor Available in a variety of wetted materials and ideal for pipe sizes up to DN900 (36 in.) Features Test certificate included for -X0, -X1 Patented Magmeter technology No
Level instruments. Continuous level measurement - Capacitance transmitters SITRANS LC300. 5/262 Siemens FI Overview.
Overview Configuration is an inverse frequency shift capacitance continuous It is ideal for standard industrial applications in chemical, hydrocarbon processing, food and beverage and mining, aggregate
5" SUBMERSIBLE PUMPS _ed.12/2014. Single member - Company subject to the control and coordination of Franklin Electric Co., Inc.
Vertical S.r.l. via Asolo, 7 36031 Dueville (Vicenza) - Italy Tel. +39 0444 361114 Fax +39 0444 365247 P.IVA e C.F. 00558130241 e-mail: sales@vertical.vi.it www.etechpumps.com Single member - Company subject
BALL VALVE WITH ADA PNEUMATIC ACTUATOR
762-763 BALL VALVE WITH ADA PNEUMATIC ACTUATOR MAIN CARACTERISTICS The 762-763 valve is a split body flanged ball valve dedicated to the automatic shut off of lines of standard fluids. With full bore construction,
Type MR 783 Magnetic level switch
Technical data sheet Magnetic level switch Houdec Instrument SAS Magnetic level switch Technical data sheet Page 0 Technical data sheet Magnetic level switch Operation A float fitted with a magnet slides
Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T ) Burst 840 bar (12200 psi) (acc. to NFPA T )
HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T 3.10.5.1) Burst 840 bar (12200 psi) (acc. to NFPA T 3.10.5.1) Housing
Level Measurement Continuous level measurement Ultrasonic transmitters
Siemens AG 2018 Overview Configuration ultrasonic level transmitter, ideal for level, volume, and volume flow measurements. It works with liquids, slurries, and bulk materials up to 12 m (0 ft). Benefits
Pressostats and thermostats CAS
MAKING MODERN LIVING POSSIBLE Technical brochure Pressostats and thermostats CAS www.danfoss.com Description CAS units are pressure-controlled switches. The position of the contacts depends on the pressure
standard and industrial pipe fittings
fittings mm sizes standard and industrial pipe fittings Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings from 6 bars to 16 bars,
V-100 product information. Variable area flowmeters for gases and liquids
V-100 product information Variable area flowmeters for gases and liquids MyScale Air mm ALU Wide-ranging and modular: Variable area flowmeters V-100 Highly modular and adaptable for almost any requirement:
Liquid filters _ 302. Deaerators. Product Bulletin
Liquid filters Deaerators _ 32 Product Bulletin WWW.VAF.NL Introduction VAF Instruments liquid filters/deaerators are used in combination with VAF flowmeters. The use of liquid filters protects downstream
CVS Rack and Pinion Pneumatic Actuator
Instruction Manual CVS Rack and Pinion Pneumatic Actuator Introduction These instructions apply specifically to the CVS Rack and Pinion pneumatic actuator. This manual provides sizing, maintenance, operation,
SUITABLE FOR EXAMPLES OF USE APPROVALS. Type approval Deutsche Bahn. Requirements. AD 2000 Data sheet A2 DIN EN ISO PED 2014/68/EU
Type test approved atmospheric discharge safety valves for industrial applications Series 8 4.2 8 Safety valves made of brass, atmospheric discharge, with threaded connections SUITABLE FOR Air, gases and
Installation Locations and Accessories for Temperature Probes
Page 1/8 Installation ocations and Accessories for Temperature Probes Ball valves T-pieces Adapter screw fittings Installation accessories The correct selection of installation locations for acquiring
MidFlow _ 135. Sliding Vane Meters DN (1-2 ) Model PT / Fuel Oil Flowmeters135. Product Bulletin
MidFlow Model PT / Fuel Oil Flowmeters135 Sliding Vane Meters DN 25-50 (1-2 ) _ 135 Product Bulletin WWW.VAF.NL 1 Introduction VAF Instruments MidFlow Model PT positive displacement sliding vane type liquid
Type S030. Operating Instructions. Symbols used. INLINE fitting. Bedienungsanleitung Manuel d'utilisation
Type S030 INLINE fitting We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. Operating Instructions Bedienungsanleitung
mass flowmeter for compressed air
mass flowmeter for compressed air VARIOMASS LC pressure and temperature compensated flowmeter easy and cost effective installation of the senor no pressure loss caused by the sensor no moving parts, i.e.
Suction Spares and Accessories 2009
MUL91600101 Black Rubber Feet for Machined Base Plates, (Pack of 5) MUL8150038 Black Rubber Feet for Machined Base Plates, (Pack of 4) b MUL94004000 Illuminated Green Rocker Switch (L30mm x W25mm x D30mm)
Technical specifications
Flow sensor, proximal For Hamilton Medical ventilators PN 281637 PN 282049 PN 282051 188 cm - 10/box 260 cm - 10/box 330 cm - 10/box Overview Diameter (ID, OD [mm]) / Description 1 Connector OD15, ventilator
Fittings Metal Push-To- Connect Fittings. We make things MOVE
Fittings Metal Push-To- Connect Fittings We make things MOVE Contents 3 Fittings 4 Product Features 4 Push-In Fittings 4 Features and Benefits 5 How it Works 5 Materials of Construction 5 Fluid 5 Operating
DISASSEMBLY AND ASSEMBLY INSTRUCTIONS FOR LIQUID RING VACUUM PUMPS WITH MECHANICAL SEALS DELTA B75
DISASSEMBLY AND ASSEMBLY INSTRUCTIONS FOR LIQUID RING VACUUM PUMPS WITH MECHANICAL SEALS DELTA B75 INTRODUCTION These instructions are for the maintenance staff in case of repair for the following pumps:
771 XS BALL VALVE WITH ADA PNEUMATIC ACTUATOR
771 XS BALL VALVE WITH ADA PNEUMATIC ACTUATOR MAIN CHARACTERISTIC The 771 XS wafer ball valve is dedicated to the automatic shut-off of low and medium pressure industrial fluids lines up to 16 bar. The
SUITABLE FOR EXAMPLES OF USE APPROVALS. Type approval Deutsche Bahn. Requirements AD 2000 Data sheet A2 DIN EN ISO PED 2014/68/EU
Type test approved atmospheric discharge safety valves for industrial applications Series 812 4.4 812 Safety valves made of brass, atmospheric discharge, with threaded connections SUITABLE FOR Air, gases
TECHNICAL CATALOGUE BALL VALVES: IDEAL
TECHNICAL CATALOGUE BALL VALVES: TEC ITAP SpA, founded in Lumezzane (Brescia) in 1972, is currently one of the leading production companies in Italy of valves, fittings and distribution manifolds for
AIRLINE EQUIPMENT CATALOGUE //
AIRLINE EQUIPMENT CATALOGUE // 16 15 14 13 12 11 10 9 The Fort Vale Range of Airline Ball & Butterfly Valves 8 Fort Vale Engineering Ltd. 2014 THIS PAGE IS INTENTIONALLY BLANK AIRLINE VALVE CATALOGUE //
INSTALLATION AND OPERATION
All Plastic Variable Area Flowmeter DFM INSTALLATION AND OPERATION Nixon Flowmeters Ltd. Leckhampton, Cheltenham, Glos UK Tel. 0044 (0) 1242 243006 Fax 0044 (0) 1242 222487 Email info@nixonflowmeters.co.uk
information service Page 1
Page 1 TO ALL OUR CUSTOMERS 1. NEW OMNIAPLUS SERIES DOMESTIC INTERLOCKED SOCKET The SCAME product line of interlocked sockets has been enhanced with the new OMNIAPLUS Series: The first interlocked socked
Metal tube flowmeters Series M21 Variable area flowmeter for low flows of liquids, gases and steam
Metal tube flowmeters Series M21 Variable area flowmeter for low flows of liquids, gases and steam Metallic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in
SXE-SSE DN PVC-U. Easyfit True Union ball and spring check valve
SXE-SSE DN 10 50 PVC-U Easyfit True Union ball and spring check valve SXE-SSE DN 10 50 The Easyfit check valve line developed with Giugiaro Design offers two different versions: SXE with ball shutter and
INTRODUCTION AND STANDARD SPECIFICATIONS
INTRODUCTION AND STANDARD SPECIFICATIONS INTRODUCTION Instrument valves and manifolds are often used on general applications for liquid and gas service and are suitable for shutting-off impulse lines to
CHOOSING YOUR MANIFOLD & LOCATION
CHOOSING YOUR MANIFOLD & LOCATION THOUGHTS ON ZONING The function of a manifold is to distribute the correct flow to each loop to meet its specific heating load. This is achieved by balancing each loop
Medical Gas Outlet Adaptor, Fitting and Hose Catalog
2018 Medical Gas Outlet Adaptor, Fitting and Hose Catalog For Clinical Engineering, Biomedical, and Respiratory, Departments 11300 Sanders Drive, Suite 1 Rancho Cordova, CA 95742 (916) 853-1222 Fax (916)
Order No light grey. Order No black
DPP- Plastic dome plug Body: Polyamide (V2 acc. to UL94) Sealing: Neopren Dynamic: -20 ~+80, short term:100 _ Easy and quick assembly Color: RAL7001 silver grey RAL7035 light grey RAL9005 black Blue, Red
Operating Instruction for Flowmonitor. Model: DF-WM
Operating Instruction for Flowmonitor Model: DF-WM 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 4 5. Operating Principle... 5 6. Mechanical Connection...
VXE DN PVC-U. Easyfit 2-way ball valve
VXE DN 10 50 PVC-U Easyfit 2-way ball valve VXE DN 10 50 FIP and Giugiaro Design designed and developed VXE Easyfit, the innovative True Union ball with union nut tightening control that permits simple
Wheel operated cylinder valve in O-ring seal design for carbon dioxide
Wheel operated cylinder valve in O-ring seal design for carbon dioxide SWN-12/C (simple valve) IWN-12/C (inline RPV) Robust construction and built to last High flow and reliable performance Low torque
Flow switches Series AD/VH
Flow switches Series AD/VH Flow switch and indicator for liquids and gases Suitable for clear, opaque or turbid liquids (series AD & VH), and for gases (series AD) Flow switching by means of magnetic coupling,
Series 812. TÜV/CE atmospheric discharge safety valves for industrial applications. Air, gases and vapours
TÜV/CE atmospheric discharge safety valves for industrial applications Series 812 4.4 812 Safety valves made of brass, atmospheric discharge, with threaded connections SUITABLE FOR Air, gases and vapours
VXE DN PVC-C. Easyfit 2-way ball valve
VXE DN 10 50 PVC-C Easyfit 2-way ball valve VXE DN 10 50 FIP and Giugiaro Design designed and developed VXE Easyfit, the innovative True union ball valve with union nut tightening control system that permits
Data sheet Pressure controls and thermostats type CAS August 2000 DKACT.PD.P10.B B0616
Data sheet Pressure controls and thermostats type CAS August 2000 DKACT.PD.P10.B2.02 520B0616 Pressure controls, type CAS Range Further 0 10 20 30 40 50 60 bar p e Type information bar page Standard pressure
ADVANCED FLUID MANAGEMENT SOLUTIONS. Sturdy and reliable industrial and diaphragm pumps. 5 YEARS ANNI DI GARANZIA WARRANTY.
ADVANCED FLUID MANAGEMENT SOLUTIONS Sturdy and reliable industrial and diaphragm pumps. 5 ANNI DI 5 YEARS WARRANTY GARANZIA Made In Italy Industrial piston pumps TECHNICAL CHARACTERISTICS Strength points
THERMOSETTER Recirculation thermal balancing valve
THERMOSETTER Recirculation thermal balancing valve 116 series 01325/17 NA ACCREDITED Function ISO 9001 FM 21654 The THERMOSETTER adjustable thermal balancing valve is used for automatic balancing of recirculation
TECHNICAL CATALOGUE GAS BALL VALVES: BERLIN
TECHNICAL CATALOGUE GAS BALL VALVES: BERLIN TEC ITAP SpA, founded in Lumezzane (Brescia) in 1972, is currently one of the leading production companies in Italy of valves, fittings and distribution manifolds
Explanations. 6 Protection (IP-Code) acc. to DIN / IEC etc. Several Icons. Manufacturing process
info@vogel-germany.de - ww.vogel-germany.de Explanations 1 2 4 5 6 8 9 10 11 In our catalogue you will find several pictograms beside the text description. They should be helpful for a quick and easier
BUTTERFLY VALVE CATALOGUE //
BUTTERFLY VALVE CATALOGUE // 11 The Fort Vale of s 1 CATALOGUE REVISION_01-.0.0 Fort Vale Engineering Ltd. 20 BUTTERFLY CATALOGUE // CONTENTS // 2 BUTTERFLY VALVES //» 2 CLAMPED WIDDOP BUTTERFLY VALVE
Mini-Pak TM 6. Industry s most advanced additive injection system for load racks with multiple injection points.
Mini-Pak TM 6 Industry s most advanced additive injection system for load racks with multiple injection points. The PCM3 electronic control module combines all the features and flexibility of six individual
VR DN PVC-U. Check valve
VR DN 10 100 PVC-U Check valve VR DN 10 100 The VR is an angle seat check valve with weighted PVC piston that allows the passage of fluid in one direction only CHECK VALVE Connection system for solvent
industrial and economy pipe fittings PVC-U Solvent Cement WELD-ON REGULAR 719 Size Code Price 500ml tin
pvcu fittings mm sizes industrial and economy pipe fittings fittings mm sizes 68 Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings
ProFlow TO BE REALLY SURE. Vane Meters. Experience in flow measurement. Introduction
ProFlow N142 P R O D U C T B U L L E T I N Vane Meters Special versions This brochure comprises only VAF Instruments standard delivery program. Special flowmeter variants can be offered as tailor-made
DK AND DK/CP DN 15 65
DK AND DK/CP DN 15 65 New diaphragm valves with maximised flow rate available in manual or pneumatically actuated versions. Manual versions are equipped with the innovative DIALOCK lockable handwheel.
VALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS
PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS The S1 model is self-operated bellows sealed pressure excess valve. This series of