Equipment Operation Manual. CA Volumetric Hand Pump Part No

Transcription

1 Equipment Operation Manual CA Volumetric Hand Pump Part No

2 Loading and Priming Screw bottle into Fluid Element Cap by turning bottle. Tighten with pliers Ensure that the lower Fluid Element Dispense Tube is clean and dust free. Fluid Element Cap Step 1 Step 3 Remove cap and nozzle from CA bottle and discard Align Fluid Element Cap so it will slide into Bottle Holder. Bottle Holder Step 2 Step 4

3 Loading and Priming Pull gently on fluid tube to align it with the center of the rollers Step 5 Step 7 Remove fluid tube from holder Close Tube Slide and apply pressure to Tube Slide Step 6 Step 8 Tube Slide

4 Loading and Priming Clamp Tube Slide with Tension Pin by pulling pin and sliding over tube slide Select Dispense Tip and install onto Luer Fitting. Secure fluid line into holder by pushing into groove. Insure that the tip is secure by pushing against back wall of holder. Step 8 Tension Pin Step 10 Vent Tube Clamp Ensure Vent Tube is Clamped Priming the CA Volumetric Hand Pump Vent Tube Step 9 Step 11 Rotate Pump Priming Knob, 20 to 40 revolutions in the direction of the arrows, until product flows from bottle to dispense tip. The pump is now primed and ready to dispense.

5 Dispense Amount Step Dispense To set dose amount, pull trigger all the way back and hold Press Stoke Adjustment Knob in Keeping hold of the trigger, rotate Adjustment Knob to one of the six dose settings and release trigger Dispensing is achieved by squeezing and releasing trigger Best results are achieved by squeezing the trigger and allowing a drop to form on the dispense tip. Once a drop is present, transfer the adhesive to the part to be bonded and release trigger Typical Dose Size Adhesive Product Max Min 1 Step 13 To change the setting push and rotate Stroke Adjustment Knob while trigger is pulled back Loctite 401 cp 110 Loctite 415 cp mg 6.5mg 7mg 5mg 6mg 4.5mg 4.5mg 3.5mg 3mg 2.5mg 1mg 1mg

6 Replacing Fluid Element Remove cap and nozzle from CA bottle and discard Align Fluid Element Cap Step 1 Step 3 Install Fluid Element to bottle Tighten to ensure a good seal Wrap fluid line around the right side of the Priming Knob and the vent line to the left Step 2 Bottle Holder Step 4 Align Fluid Element Cap so it will slide into Bottle Holder

7 Replacing Fluid Element Vent Tube Clamp Vent Tube Step 5 Pull gently on fluid tube to align it with the center of the rollers Pull gently on vent tube and place into groove. Clamp in place with Vent Tube Clamp Step 7 Close fluid Tube Slide on to fluid line and clamp in place by pulling the Tension Pin and sliding over the Tube Slide. Tube Slide Vent Side Tension Pin Close Tube Slide on to vent tube and clamp in place by pulling the Tension Pin and sliding over the Tube Slide. Step 6 Step 8 Figure 20

8 CA Volumetric Hand Pump Replacing Fluid Element Rotate Pump Priming Knob, 20 to 40 revolutions in the direction of the arrows, until product flows from bottle to dispense tip. The pump is now primed and ready to dispense. Step 9 Step 11 Select Dispense Tip and install onto Luer Fitting. Secure fluid line into holder by pushing into groove. Insure that the tip is secure by pushing against back wall of holder. Step 10 Step 12 Dispensing of adhesive is achieved by squeezing trigger, touching adhesive drop onto part, and then releasing trigger.

9 Spare Parts Black Fluid Element Assembly PN Amber SS Needle, 15 GA 50 Pack Item Number Grey Taper Tip, 16 GA 50 Pack Item Number Green SS Needle, 18 GA 50 Pack Item Number Clear Fluid Element Assembly PN

10 Troubleshooting Malfunction Does not prime Possible cause Correction Fluid Element is not correctly installed Dispense tip is clogged Dispense tip is too small Difficult to control drop dispensing Repeat Fluid Element installation Steps 5-12 Tip gently stretch dispense tip when installing Fluid Element Change dispense tip Use larger dispense tip Use a smaller dispense setting, see Dispense Amount Slowly squeeze trigger

11 Henkel Corporation One Henkel Way Rocky Hill, CT Henkel Canada Corporation 2225 Meadowpine Boulevard Mississauga, Ontario L5N 7P2 Henkel Capital, S.A. de C.V. Calzada de la Viga s/n Fracc. Los Laureles Loc. Tulpetlac, C.P Ecatepac de Morelos, Edo. de México Henkel Corporation Automotive / Metals HQ Stephenson Hwy. Madison Heights, MI Henkel Ltda. Rua Karl Huller, 136 Jd. Canhema Diadema/SP, Brazil and designate trademarks of Henkel Corporation or its affiliates. = registered in the U.S. and elsewhere. Henkel Corporation, All rights reserved. Data in these instructions is subject to change without notice. Manual P/N: , Rev 1, Date: July 2011