Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987
|
|
|
- Ambrose Foster
- 5 years ago
- Views:
Transcription
1 Timing Chain: Service and Repair Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 PREPARATION FOR REMOVAL OF TIMING CHAIN 1. REMOVE CYLINDER HEAD 2. REMOVE RADIATOR 3. REMOVE OIL PAN (a) Remove the engine undercover. (b) Remove the engine mounting bolts. (c) Place a jack under the transmission and raise the engine approx. 25 mm (0.98 in. ). ( d) Remove the sixteen bolts and two nuts. ( e) Using SST and brass bar, separate the oil pan from the cylinder block. SST NOTE: When removing the oil pan, be careful not to damage the oil pan flange. REMOVAL OF TIMING CHAIN 1. ( with PS) REMOVE PS BELT 2. ( with A/C) REMOVE A/C BELT, COMPRESSOR AND BRACKET
2 3. REMOVE FLUID COUPLING WITH FAN AND WATER PUMP PULLEY (a) Loosen the water pump pulley set bolts. (b) Loosen the belt adjusting bolt and pivot bolt of the alternator, and remove the drive belt. ( c) Remove the set nuts, fluid coupling with fan and water pump pulley. 4. REMOVE CRANKSHAFT PULLEY (a) (with A/C) Remove the No.2 crankshaft pulley. (b) Using SST to hold the crankshaft pulley, loosen the pulley bolt. SST and (c) Using SST, remove the crankshaft pulley. SST REMOVE NO.1 WATER BY-PASS PIPE (22R) Remove the three bolts and pipe. (22R- E) Remove the two bolts and pipe. (22R- TE) Remove the two bolts, and disconnect the pipe from the timing chain cover.
3 6. (22 R, 22R-E) DISCONNECT HEATER WATER OUTLET PIPE Remove the two bolts, and disconnect heater water outlet pipe. (22R- TE) REMOVE NO.3 TURBO WATER PIPE Remove the two bolts and No.3 turbo water pipe. 7. REMOVE FAN BELT ADJUSTING BAR Remove the three bolts and bar. 8. REMOVE CHAIN COVER ASSEMBLY (a) Remove ten timing chain cover bolts shown by the arrows. (b) Using a plastic faced hammer, loosen the chain cover and remove it. 9. REMOVE CHAIN AND CAMSHAFT SPROCKET (a) Remove the chain from the damper. (b) Remove the cam sprocket and chain together.
4 10. REMOVE PUMP DRIVE SPLINE AND CRANKSHAFT SPROCKET If the oil pump drive spline and sprocket cannot be removed by hand, use SST to remove them together. SST REMOVE GASKET MATERIAL ON CYLINDER BLOCK INSPECTION OF COMPONENTS 1. MEASURE CHAIN AND SPROCKET WEAR (a) Measure the length of 17 links with the chain fully stretched. (b) Make the same measurements at least three other places selected at random. Chain elongation limit at 17 links: mm (5.787 in.) If over the limit at any one place, replace the chain. (c) Wrap the chain around the sprocket. (d) Using a vernier caliper, measure the outer sides of the chain rollers as shown. Measure both sprockets. Crankshaft sprocket minimum: 59.4 mm (2.339 in.) Camshaft sprocket minimum: mm (4.480 in.) If the measurement is less than minimum, replace the chain and two sprockets.
5 2. MEASURE CHAIN TENSIONER Using a vernier caliper, measure the tensioner as shown. Tensioner minimum: 11.0 mm (0.433 in.) If the tensioner is worn or less than minimum, replace the chain tensioner. 3. MEASURE CHAIN DAMPERS (a) Using a micrometer, measure each damper. Damper wear limit: 0.5 mm (0.020 in.) If either damper is worn or less than minimum, replace the damper. INSTALLATION OF TIMING CHAIN 1. INSTALL CRANKSHAFT SPROCKET AND CHAIN (a) Turn the crankshaft until the shaft key is on top. (b) Slide the sprocket over the key on the crankshaft. (c) Place the timing chain on the sprocket with the single bright link aligned with the timing mark on the sprocket. 2. PLACE CHAIN ON CAMSHAFT SPROCKET (a) Place the timing chain on the sprocket so that the space between the bright chain links is aligned with the timing mark. (b) Make sure the chain is positioned dampers. (c) Turn the camshaft sprocket counterclockwise to take the slack out of the chain.
6 3. INSTALL OIL PUMP DRIVE SPLINE Slide the oil pump drive spline over the crankshaft key. NOTE: If the oil pump drive spline is difficult to install by hand, install using SST. SST ( ) 4. INSTALL TIMING CHAIN COVER ASSEMBLY (a) Remove the old cover gaskets. Clean the gasket surface. Install new gaskets over the dowels. (b) Slide the cover assembly over the dowels and pump spline. ( c) Insert the bolts as shown and torque them. Torque: 8mm bolt 130 kg-cm (9 ft-lb, 13 N.m) 10 mm bolt 400 kg-cm (29 ft-lb, 39 N.m ) 5. INSTALL FAN BELT ADJUSTING BAR (a) Temporarily install the adjusting bar to the alternator. (b) Install the adjusting bar to the chain cover and cylinder head. Torque: 130 kg-cm (9 ft-lb, 13 N.m) 6. (22 R, 22R-E) INSTALL HEATER WATER OUTLET PIPE Connect the heater water outlet pipe to the timing gear cover with two bolts.
7 (22R- TE) INSTALL NO.3 TURBO WATER PIPE Install the No.3 turbo water pipe with the two bolts. 7. INSTALL NO.1 WATER BY-PASS PIPE (22R) Install the pipe with the three bolts. (22R- E) Install the pipe with the two bolts. (22R- TE) Connect the pipe to the timing chain cover with the two bolts. 8. INSTALL CRANKSHAFT PULLEY (a) Install the crankshaft pulley and bolt. (b) Using SST to hold the crankshaft pulley, torque the bolt. SST and Torque: 1600 kg-cm (116 ft-lb, 157 N.m) (c) (with A/C) Install the No.2 crankshaft pulley. 9. INSTALL WATER PUMP PULLEY AND FLUID COUPLING WITH FAN (a) Temporarily install the water pump pulley and fluid coupling with fan with four nuts. (b) Place the drive belt on to each pulley. (c) Stretch the belt tight and tighteen the four nuts. 10. ADJUST DRIVE BELT TENSION 11. ( with A/C) INSTALL A/C COMPRESSOR BRACKET, COMPRESSOR AND BELT 12. (with PS) INSTALL PS BELT 13. INSTALL OIL PAN (a) Remove any old packing material and be careful no to drop any oil on the contacting surfaces of the oil pan and cylinder block. ^ Using a razor blade and gasket scraper, remove all the packing (FIPG) material from the gasket surfaces.
8 ^ Thoroughly clean all components to remove all the loose material. ^ Clean both sealing surfaces with a non-residue solvent. CAUTION: Do not use a solvent which will affect the painted surfaces. (b) Apply seal packing to the joint part of the cylinder block and chain cover, cylinder block and rear oil seal retainer. Seal packing: Part No or equivalent (c) Apply seal packing to the oil pan as shown in the figure. Seal packing: Part No or equivalent ^ Install a nozzle that has been cut to a 5-mm (0.20 in.) opening. NOTE: Avoid applying an excess amount to the surface. Be especially careful near oil passages. ^ Parts must be assembled within 5 minutes of application. Otherwise, the material must be removed and re-applied. ^ Immediately remove nozzle from tube and reinstall cap. (d) Install the oil pan over the studs on the block with sixteen bolts and two nuts. Torque the bolts and nuts. Torque: 130 kg-cm (9 ft-lb, 13 N.m) (e) Lower the engine and install the engine mounting bolts. (f) Install the engine under cover. POST INSTALLATION 1. INSTALL RADIATOR 2. INSTALL CYLINDER HEAD
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) 2002 Timing Chain: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4 WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
2004 Toyota RAV ENGINE Lubrication - RAV4
2004 ENGINE Lubrication - RAV4 OIL AND FILTER INSPECTION 1. CHECK ENGINE OIL QUALITY Check the oil for deterioration, entry of water, discoloring or thinning. If the quality is visibly poor, replace the
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
3/13/ :32 AM. NOTICE: Do not disconnect the hose.
1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal
1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
![1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder](/thumbs/95/123571962.jpg "1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder")
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
EM 27 2UZ-FE ENGINE MECHANICAL CAMSHAFT REMOVAL
2UZ-F NGIN MCHANICAL CAMSHAFT M 27 RMOVAL 1. RMOV TIMING BLT (See page M-18) 2. RMOV IGNITION COIL ASSMBLY (a) Disconnect the 4 ignition coil connectors. (b) Remove the 4 bolts and 4 ignition coils. 3.
ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)
ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See
LU 8 LUBRICATION SYSTEM. Oil Pump OIL PUMP COMPONENTS
LU8 OIL PUMP COMPONENTS LU9 REMOVAL OF OIL PUMP (See page LU8) 1. RAISE VEHICLE NOTICE: Be sure the vehicle is securely supported. 2. REMOVE ENGINE UNDERCOVER 3. DRAIN ENGINE OIL (a) Remove the oil filler
2001 Toyota MR ENGINES' '1.8L 4-Cylinder
TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
INSTALLATION NOTICE: EM 25. Align. Align. Align. Pin. (c) (a) (b) ENGINE MECHANICAL (2RZ FE, 3RZ FE) 2003 TOYOTA TACOMA (RM1002U) P15100 P15081 Z15266
P15100 INSTLLTION EM25 EM16P01 Check that No.1 cylinder is at TDC and that the weights of the No.1 and No.2 balance shafts are at the bottom side. 1. INSTLL NO.4 VIRTION DMPER Install the No.4 damper with
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
Remove four nuts, then the cooling fan assembly.
The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.
Oil Pan Seal Cutter Oil Filter Wrench Transmission & Transfer Bearing Replacer. ( ) Replacer Pipe
EG359 PREPARATION SST (SPECIAL SERVICE TOOLS) 0903200100 Oil Pan Seal Cutter No.2 oil pan 0922807500 Oil Filter Wrench 0931660010 Transmission & Transfer Bearing Replacer (0931600010) Replacer Pipe Crankshaft
EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION
EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should
REMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
TIMING BELT TIMING BELT
TIMING BELT TIMING BELT DISASSEMBLY 1. Lift the vehicle by using of jack. 2. Remove the engine support bracket. (14 mm bolt and 2 nuts, 17 mm bolt) 3. Remove the power steering belt. 4. Remove the air
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT
2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page
1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)
ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
ENGINE MECHANICAL PREPARATION SST mm Socket Wrench for 12 Pointed Head
SST 027 023HH01 0901138121 12 mm Socket Wrench for 12 Pointed Head CYLINDER BLOCK ASSY(2AZFE) PARTIAL ENGINE ASSY(3MZFE) (3MZFE) NO.2(3MZFE) CYLINDER BLOCK ASSY(3MZFE) 0903200100 Oil Pan Seal Cutter PARTIAL
1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
TIMING BELT (5S FE) COMPONENTS
ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576
INSTALLATION. Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
M20 Timing Mark NGIN MHNIL INSTLLTION M19G01 1. INSTLL MSHFT TIMING SPROKT ND VVT TIMING SPROKT (a) lign the camshaft knock pin with the knock pin groove on the sprocket side with the timing mark, and
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
TIMING BELT (4A FE) COMPONENTS
EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
Technical Service BULLETIN
Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may
Timing Belt: Service and Repair
2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata
Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002
Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR
2000 Nissan Altima SE
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
ENGINE MECHANICAL PREPARATION SST mm Socket Wrench for 12 Pointed Head Union Nut Wrench 12mm PARTIAL ENGINE ASSY(1ZZ FE)
SST 025 021E001 0901138121 12 mm Socket Wrench for 12 Pointed Head CYLINDER BLOCK(1ZZFE) 0902338200 Union Nut Wrench 12mm 0903200100 Oil Pan Seal Cutter 0920101055 Valve Guide Bushing Remover & Replacer
2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
Chrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
Intake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
COOLANT COOLANT INSPECTION HINT: Check the coolant level when the engine is cold. 1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR The engine coolant level should be between the LOW and FULL lines at
1990 Buick Electra Limited
4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
Engine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
1999 Nissan Altima GLE
TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure
1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.
1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket
Timing Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
Intake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
Page 1 of 11 Assembly 50. Install the timing chain guide. Tighten to 12 Nm. Page 2 of 11 51. Install the crankshaft sprocket. 52. Install the chain tensioning tool 303-532 to the exhaust camshaft sprocket.
2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat.
31. Remove the 3 bolts, thermostat housing and thermostat. 32. Remove the 2 bolts, stud bolt and the A/C compressor. 33. Remove the bolt and the KS. 34. Remove the 8 bolts and the crankcase vent oil separator.
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E
TIMING CHAIN Removal and Installation PFP:13028 EBS00I2X A EM C D E F G H I J K L M KBIA2511E EM-35 1. Camshaft sprocket (left bank EXH) 2. Camshaft sprocket (left bank INT) 3. Camshaft sprocket (right
Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
Timing Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
<4D5> ENGINE Click on the applicable bookmark to selected the required model year
ENGINE 11B-2 ENGINE General Information GENERAL INFORMATION 11100010339 Items 4D56 Total displacement m 2,477 Bore x Stroke mm 91.1 x 95.0 Compression ratio 21 Combustion chamber Camshaft
TIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL
Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.
1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Service and Repair» Procedures» Timing Drive Components Timing Drive Components Special Tools And Equipment Special Tool(s) Material Material
2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
REMOVAL AND INSTALLATION
2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT
Sealing flanges and flywheel/drive plate, removing and installing
Page 1 of 20 13-47 Sealing flanges and flywheel/drive plate, removing and installing Note: For repairs to the clutch: Repair Manual, 5 Spd. Manual Transmission 012/01W Front Wheel Drive, Repair Group 30
Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove