& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.
|
|
- Julius Bradley
- 5 years ago
- Views:
Transcription
1 Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace & MX-6 This engine is classified as an Interference engine. If the timing belt breaks or jumps timing, a piston may contact an open valve. Piston to valve contact may cause damage to the valve, piston and other engine components. In some cases valve to valve contact may be experienced when the timing belt breaks or jumps timing. To avoid belt breakage, replace the timing belt as recommended by the vehicle manufacturer timing belt replacement interval. With the timing belt removed, avoid turning the camshaft or crankshaft. If movement is required, exercise extreme caution to avoid valve damage caused by piston contact. 1. Disconnect and isolate the battery ground cable. 2. Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands. 3. Remove the righthand front wheel and tire, then the splash shield. 4. Remove the power steering pump drive belt and the alternator drive belt. 5. Remove the power steering pump drive belt idler pulley shield. 6. Remove the power steering hose brackets. 7. Remove the water pump pulley. 8. Remove the crankshaft pulley and the timing belt guide. 9. Tag the ignition leads, then remove them from the spark plugs. 10. Remove the spark plugs. 11. Disconnect the oil separator hose from the valve cover. 12. Disconnect the PCV hose from the valve cover. 13. Alternately and evenly loosen the valve cover attaching bolts in sequence, Fig /7
2 14. Remove the engine oil dipstick tube. Discard the O-ring. 15. Remove the timing belt upper and lower covers. 16. Attach a suitable engine support and lifting fixture, then raise the engine slightly. 17. Disconnect the ground harness, then remove the righthand engine support insulator. 18. Ensure the crankshaft sprocket mark is aligned with the engine mark and the camshaft sprocket timing marks (I and E) are properly aligned, Fig Rotate the timing belt tensioner pulley using a suitable hex wrench, then remove the timing belt tensioner spring. 20. Remove the timing belt from the sprockets. 21. Ensure the crankshaft sprocket and camshaft sprocket timing marks are still aligned, Fig Install the new timing belt over the sprockets. Ensure the timing belt tension side is taut. 23. Rotate the timing belt tensioner pulley clockwise using a hex wrench, then install the tensioner spring. 24. Rotate the crankshaft two turns in the normal rotation direction. 25. Ensure the crankshaft and camshaft sprocket timing marks are aligned, Fig Install the righthand engine support insulator, then remove the engine support and lifting fixture. 27. Install the timing belt lower and upper covers. 28. Install the engine oil dipstick tube with a new O-ring. 29. Apply a suitable silicone sealant to the shaded areas of the cylinder head as illustrated, Fig Alternately and evenly tighten the valve cover attaching bolts in sequence, Fig Connect the PCV hose to the valve cover. 32. Connect the oil separator hose to the valve cover. 33. Connect the ignition leads to the spark plugs. 34. Install the spark plugs. Torque them to ft. lbs. 35. Remove the crankshaft pulley and the timing belt guide. 2/7
3 36. Install the water pump pulley. 37. Install the power steering hose brackets. 38. Install the power steering pump drive belt idler pulley shield. 39. Install the power steering pump drive belt and the alternator drive belt. Refer to "Accessory Drive Belt Tension" for proper belt tension. 40. Install the splash shields, then the righthand front wheel and tire. 41. Lower the vehicle, then tighten the lug nuts. 42. Connect the battery ground cable. 43. Inspect and adjust the ignition timing as required. 3/7
4 Fig. 1 Valve cover bolt loosening sequence. 626, MX-6 & Protege 4/7
5 Fig. 2 Crankshaft & camshaft sprocket timing marks. 626, MX-6 & Protege 5/7
6 Fig. 3 Valve cover sealing locations. 626, MX-6 & Protege 6/7
7 Fig. 4 Valve cover bolt tightening sequence. 626, MX-6 & Protege Copyright 2018 Hearst Business Media. All Rights Reserved. 7/7
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More information2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
More informationENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L >
Print 2003 Subaru Forester 2.5L Eng X ENGINE CONTROLS - ON-VEHICLE ADJUSTMENTS ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > 1. Set the vehicle onto the lift. 2. Lift-up the vehicle. 3. Remove
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationTECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
More information1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
More informationMazda3 - Workshop Manual - Engine
Page 1 of 18 2005 - Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More information2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum
1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationLAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.
1 Vehicle LAND ROVER GROUP / Freelander I 2.5 V6 / 09/2001-03/2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.5 / 130 kw Motor tag KV 6 MPI RB key LRG 48 Replacement Interval Guide
More information4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)
TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the
More informationRemoval. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationTiming Belt: Service and Repair Removal and Installation Removal
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Removal and Installation Removal 1. Turn the crankshaft so its white mark (A) lines up with the
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationPage 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1992 and earlier model years, the manufacturer recommends the belt be replaced every 60,000 miles. For 1993-95
More informationChrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
More informationTesting and Inspection. Diagnostic Procedure Step 1-2
1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationPEUGEOT / 206 CC 1.6i 16V / 09/ /2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag RB key PEU 814
1 Vehicle PEUGEOT / 206 CC 1.6i 16V / 09/2000-03/2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag NFU RB key PEU 814 Replacement Interval Guide Peugeot recommend: 206:
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required
More information3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]
1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More informationTiming Belt: Service and Repair
1996 Honda Accord Sedan L4-2.2L SOHC (16 Valve) Copyright 2009, ALLDATA 9.90 Page 1 Timing Belt: Service and Repair TIMING BELT AND TIMING BALANCER BELT REMOVAL Timing Components NOTE: - Turn the crankshaft
More informationTIMING BELT REMOVAL/INSTALLATION [ZM]
ALLDATA Online - 2000 Mazda Protege LX L4-6L DOHC - Service an... 1 of 8 6/26/2012 7:53 PM TIMING BELT REMOVAL/INSTALLATION [ZM] 5. 6. 7. 8. 9. Disconnect the negative battery cable. Remove the CMP sensor.
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More information1 of 17 2/19/ :10 AM TIMING BELT
1 of 17 2/19/2012 11:10 AM TIMING BELT 2 of 17 2/19/2012 11:10 AM INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 3 of 17 2/19/2012 11:10 AM 2) Install left-hand belt cover No.2. 3) Install
More information2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More informationREMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
More informationThe following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationALLDATA Online Land Rover Freelander (LN) V6-2.5L - Camshaft Timing Belt
Page 1 of 13 Camshaft Timing Belt Service Repair No - 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt. 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
More information2003 Land Rover Freelander S. CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed.
FRONT TIMING BELT CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed. Removal CAUTION: Camshaft timing belt must be replaced if cylinder head is to be
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationTECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.
SERVICE V8 XJ Series DATE 12/02 TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump 100-21 MODEL 2002 MY V8 XJ Series VIN F44114 - F55936 Issue: Some 2002
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT
More information5.7L ENGINE PARTS BOOK. Not for. Reproduction
5.7L ENGINE PARTS BOOK Engine Model: Engine Family: PSI, Industrial Engine Spec N.: 39004120-39004248 Parts Book Revision: December, 2015 TABLE OF CONTENTS SECTION PAGE CYLINDER BLOCK... 3-5 CYLINDER HEAD...
More information1 of 15 1/26/2017 8:57 AM
1 of 15 1/26/2017 8:57 AM Timing Belt and Balancer Belt Removal Special Tools Required ^ Holder Handle 07JAB-001020A ^ Holder Attachment, 50 mm, Offset 07MAB-PY3010A ^ Socket, 19 mm 07JAA-001020A or a
More informationTiming Drive Components ( )
Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position
More information1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE).
1Search TIMING BELT 2005 Chrysler Pacifica 3.5L Eng Base FRONT TIMING BELT COVER REMOVAL 1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE). 2. Disconnect
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More information2001 Escort Workshop Manual
Page 1 of 6 SECTION 303-01B: Engine 2.0L Zetec 2001 Escort Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/26/2004 Timing Drive Components Timing Belt Special Tool(s) Crankshaft TDC Timing
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More information2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for 10) Install
More informationTiming Belt: Service and Repair Timing Belt Replace. Timing Belt Removal
1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley
More informationTiming Belt and Timing Balancer Belt
Replacement Turn the crankshaft so that the No. 1 cylinder is at TDC (page 6-25). 1. Remove the splash shield. 3. Remove the mounting bolt, nut and V-belt from the power steering pump, then remove the
More informationValve Cover - RH Material
1 of 5 5/15/2015 8:06 AM Valve Cover - RH Material 2 of 5 5/15/2015 8:06 AM 3 of 5 5/15/2015 8:06 AM Removal CAUTION: During engine repair procedures, cleanliness is extremely important. Any foreign material,
More informationTiming Belt: Service and Repair Removal
2001 Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Removal Special Tools Required ^ Holder handle 07JAB-001020A ^ Holder attachment,
More informationTiming Belt and Timing Balancer Belt
Replacement CAUTION: Inspect the water pump when replacing the timing belt (page 10-12). NOTE: Turn the crankshaft so that the No. 1 piston is at TDC (page 6-106). 1. Remove the splash shield. 3. Remove
More informationVALVE TIMING CHECK-TIMING BELT COVER INSTALLED
TIMING BELT SERVICE VALVE TIMING CHECK-TIMING BELT COVER INSTALLED 1. Remove number one spark plug. 2. Using a dial indicator; set number one cylinder to TDC on the compression stroke. 3. Remove the access
More information5-18 ENGINE TOP END. Cylinder Head Cover
5-18 ENGINE TOP END Cylinder Head Cover Cylinder Head Cover Installation Replace the head cover gasket [A] with a new one. Apply silicone sealant [B] to the cylinder head as shown. Sealant - Kawasaki Bond
More information2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More information8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
More information1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationMazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: VARIABLE VALVE TIMING (VVT) NOISE AND/OR TIMING CHAIN NOISE Bulletin No: 01-012/12 MULTI-MODEL (L3 TURBO) - VARIABLE VALVE
More informationService and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More informationREMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section.
303-01B-1 303-01B-1 REMOVAL Cylinder Head Material Item Specification Special Tool(s) Motorcraft Metal Surface Prep Modular Engine Lift Bracket ZC-31 303-F047 (014-00073) or equivalent Silicone Gasket
More informationTiming Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.
Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationIN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
More informationAcura ZDX V6-3.7L 2010-Timing Belt: Service and Repair
Acura ZDX V6-3.7L 2010-Timing Belt: Service and Repair Timing Belt Removal Timing Belt Removal 1. Turn the crankshaft so its white mark (A) lines up with the pointer (B). NOTE: The other pointer (C) is
More information10 +/- 2 degrees before top dead center (BTDC)
1996 Ford Contour L4-122 2.0L DOHC VIN 3 SFI Ignition Timing Adjustments Base ignition timing is referenced to the position of the crankshaft position sensor. It is set at 10 +/- 2 degrees before top dead
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner
More informationInstallation Instructions
Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.
More informationFig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover
Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and
More information