Angle Mounted Master Cylinder Bleeding Procedure
|
|
- Loreen Eaton
- 5 years ago
- Views:
Transcription
1
2 Angle Mounted Master Cylinder Bleeding Procedure All angle-mounted master cylinders. Unable to obtain a firm brake pedal when bleeding master cylinder on vehicle Cause: Air trapped in the upper end of the master cylinder past the secondary port. When bleeding brakes system, raise rear of vehicle until master cylinder bore is level as shown below. CAUTION: Some fluid should be removed from the reservoir to avoid spilling as vehicle is raised. Always flush entire brake system with approved fluid when any brake component is replaced. JDA5256 PT
3 DIAGONAL SPLIT BLEEDING SEQUENCE FWD vehicles with diagonal split brake systems. Brake system won t bleed, uneven pad wear, low brake pedal, or warning lights that won t go out. Cause: Improper brake bleeding sequence. Brake systems on most FWD vehicles have been redesigned to insure adequate stopping power in the event of partial system failure. To ensure proper system performance these diagonal split systems require a special bleeding sequence, usually RR, LF, LR, RF. Refer to manufacture s bleeding sequence for your vehicle. When replacing brake components, always flush entire brake system with approved brake fluid from a sealed container. JDA5235 PT
4 Brake Hose May Cause Low Pedal All vehicles with power brakes. How to diagnose a sinking, low or spongy brake pedal. 1. Begin by isolating the master cylinder. Remove the lines from the master cylinder and insert blocking plugs into the ports. Press on the brake pedal. If the pedal is firm and hard, the master cylinder is good. If the pedal still drops, either air is in the unit or it is bypassing internally. Bleed the unit or replace as necessary. Reconnect and bleed the system. 2. With a properly bled master cylinder test the brake hoses. Using a proper tool, carefully pinch off all the rubber brake hoses as close to the master cylinder as possible. Release one brake hose at a time. Press the brake pedal. If the brake pedal is firm and hard, move to the next circuit. Repeat until the circuit containing the defective component is located (the brake pedal will be soft or sinking). Replace defective components as necessary. 3. Flush the system thoroughly with fresh brake fluid from a sealed container according to the manufacturer s service procedures. Pinch off hose close to master cylinder Flush system with fresh brake fluid after repairs Contaminated Fluid JDA5237 PT
5 Choose the Right Brake Fluid It Does Matter All vehicles. Choosing which type (DOT 3, 4, or 5) of brake fluid for your brake system. Does it really matter? YES! It s very important the fluid specified by the original vehicle manufacturers must be used. DOT 3 & 4 brake fluid is a mineral based fluid. DOT 5 is silicone based. Never mix the two types. DO NOT use DOT 5 in a vehicle equipped with ABS (Anti-Lock Brake System). Foaming of the fluid will occur due to the pulsed high pressure action of the ABS system under braking. To determine which fluid should be used for your vehicle, simply consult the shop manual or look on the master cylinder lid or reservoir body. Brake Fluid Specifications Located on Lid Caution: If two different brake fluids have been mixed, the brake system should be flushed, and fresh brake fluid recommended by the vehicle s manufacturer should be installed. JDA8338 PT
6 Can I Mix Brake Fluid? All vehicles. Question: Can I mix brake fluid? Answer: NO! When servicing a brake system you must always replace the brake fluid using OE specified brake fluid. Replacing the fluid avoids contaminating the entire brake system. Mixing fluids or using petroleum based fluids will destroy seals and gaskets throughout the entire brake system (see example), causing catastrophic brake failure. This can result in vehicle damage and/or personal injury. Contaminated Good Mixing or using the wrong brake fluid will void the warranty. Always refer to manufacturer's specifications when selecting the proper brake fluid. Always use new fluid from an unopened container. MS9349 PT
7 Brake Lock-up Nissan Quest and Mercury Villager ( & ) Cause: Nissan Quest/Mercury Villager minivans with ABS (up to the 2002 model year). Master Cylinder and Left front/right rear brake is locking up. Contaminated brake fluid may have blocked the ABS modulator valves or the Dampener Valve. The Dampener Valve is a component that is screwed into one of the outlet ports of the master cylinder. The brake line for the left front and right rear brakes come out of this part. Another possibility is ABS system component failure causing brake pressure not to be released. 1. The first step is to examine brake fluid condition for signs of debris and contamination; flushing and replace the fluid as needed. 2. Next verify there are no ABS codes. Faulty wheel sensors (code 21) can cause false ABS actuator operation resulting in wheel lock-up. Repair or replace as necessary, then clear ABS codes and verify operation. 3. Before replacing the master cylinder, the dampener valve, or the ABS Actuator, loosen the master cylinder so it can be pulled away from the brake booster to eliminate the possibility of brake pedal free play or a pushrod adjustment problem. While this type of problem usually affects all four brakes, it does allow the master cylinder and linkage to be isolated. If the brakes still do not release, loosen the brake line from the dampener valve and verify the brakes free up. If the brake fluid pressure is not releasing on its own, this may indicate a problem in the ABS actuator or the dampener valve that is blocking release of brake fluid pressure back to the reservoir. In most cases the cause of the lock-up is the accumulation of debris and contamination that is effecting the operation of the ABS unit or the dampener valves. Proper periodic flushing and replacement of the brake fluid will help avoid this lock-up problem. Please refer to your vehicle s service manual for specific diagnostic instructions. This ProTech bulletin is supplied as technical information only and is not an authorization for repair. JDB1230 PT
ALLDATA Online Saturn L200 L4-2.2L VIN F - Base Brake Bleeding. Base Brake Bleeding
Page 1 of 9 Base Brake Bleeding BASE BRAKE BLEEDING TOOLS REQUIRED J-439l5 Brake Bleed Adapter J29532 Pressure Bleeder MANUAL BLEEDING NOTICE: Brake fluid is corrosive to painted surfaces. Take care not
More informationWeak or No Booster Assist Due to Vac Hose Problems
Weak or No Booster Assist Due to Vac Hose Problems All vehicles equipped with vacuum brake boosters. Weak or no power assist. Insufficient vacuum volume to operate booster at maximum efficiency. Check
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1992 Infiniti G20 1990-92 BRAKES Infiniti Anti-Lock Brake System Infiniti; G20, M30, Q45 DESCRIPTION & OPERATION The Anti-Lock Brake System (ABS) prevents wheel lock-up during abrupt
More informationClass 5 to 7 Truck and Bus Hydraulic Brake System
Class 5 to 7 Truck and Bus Hydraulic Brake System Diagnostic Guide 2nd Edition www.bosch.us Important Service tes The information in this publication was current at the time of printing. The information
More informationDESCRIPTION & OPERATION
2004 BRAKES Disc - TSX DESCRIPTION & OPERATION WARNING: DO NOT use air pressure or a dry brush to clean brake assemblies. Avoid breathing brake dust. Use OSHA-approved vacuum cleaner for cleaning and collecting
More informationDESCRIPTION & OPERATION
DESCRIPTION & OPERATION ANTI-LOCK BRAKING 1998-99 BRAKES Anti-Lock/TCS - Corvette The Anti-Lock Brake System (ABS) and Traction Control System (TCS) increases vehicle control during severe deceleration
More informationHydraulic Brake System, Bosch 42.15
Hydraulic Brake System, Bosch 42.15 Index Hydraulic Brake Index Subject Figure Brake warning lamp and buzzer related to parking brake Fig. 1 Brake warning lamp and buzzer related to service brake Fig.
More informationBLEEDING BRAKE SYSTEM
BLEEDING BRAKE SYSTEM CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. Bleed hydraulic system
More informationInstructions Suzuki Samurai Brake System Bleeding. Suggested Tools:
86-95 Suzuki Samurai Brake System Bleeding Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment. Suggested Tools: Brake Fluid, DOT
More informationAnti-lock Brake System (ABS),
Page 1 of 6 45-18 Anti-lock Brake System (ABS), Bosch 5.3 A traction control system (TCS/ASR) is available as optional equipment for front-wheel-drive models. The brake system of the ABS is split diagonally.
More informationSECTION 4A BRAKE SYSTEM TABLE OF CONTENTS
SECTION 4A BRAKE SYSTEM TABLE OF CONTENTS Description and Operation... 4A-2 Braking System Testing... 4A-2 Hydraulic Brake System... 4A-2 Brake Pedal... 4A-2 Master Cylinder... 4A-2 Brake Booster... 4A-3
More informationGENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench
206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent
More informationInstallation Guide. Installing the FRK Hydraulic Compact Unit (HCU) with Parking Brake Valve on International School Buses
Revised 09-18 Installation Guide Revised 1 Technical 09-18 Bulletin Installing the FRK 08-10086 Hydraulic Compact Unit (HCU) with Parking Brake Valve on International School Buses Hazard Alert Messages
More informationDevac Tool for Hard-to-Bleed Ford Power Steering Systems
Devac Tool for Hard-to-Bleed Ford Power Steering Systems All power steering equipped vehicles (especially Ford) Whine or moan noise from power steering pump Air trapped in the power steering system The
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT BIG BRAKE CONVERSION KIT A112-5 1987-93 FORD MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1993 Mitsubishi Diamante 1993 BRAKES Mitsubishi - Anti-Lock Brake System Diamante DESCRIPTION The Anti-Lock BRAKE SYSTEM (ABS) is designed to prevent wheel lock-up during heavy braking.
More informationTRACTION CONTROL SYSTEM 1996 Toyota Supra 1995-96 BRAKES Traction Control Supra DESCRIPTION Toyota Traction Control (TRAC) system controls engine torque and braking of the driving wheels. TRAC system is
More informationUNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS Ford Ra... UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN
Page 1 of 5 UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN Reference Number(s): 93-12-19, Date of Issue: June 9, 1993 CONDITIONS CLUTCH - "SOFT" UNRESPONSIVE CLUTCH PEDAL
More informationVacuum Bleeder Kit. Product:
Vacuum Bleeder Kit Product: 119-020 Warning! These pumps are not approved for use with combustible materials such as gasoline, kerosene, or diesel fuel. Serious injury or damage may occur if pump is used
More informationBRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM
Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see
More informationBASIC BRAKE SYSTEM GROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-3 BASIC BRAKE SYSTEM DIAGNOSIS 35A-6
35A-1 GROUP 35A BASIC BRAKE SYSTEM CONTENTS GENERAL DESCRIPTION......... 35A-3 DIAGNOSIS 35A-6 INTRODUCTION..................... 35A-6 DIAGNOSTIC TROUBLESHOOTING STRATEGY......................... 35A-6
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125-42 GM 10 & 12 Bolt Rear Axles with Staggered or non-staggered Shocks with C-Clips Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationInstalling FRK and FRK Hydraulic Compact Unit (HCU) on Navistar Straight Trucks
Revised 09-18 Technical Bulletin Installing FRK 09-10091 and FRK 09-10092 Hydraulic Compact Unit (HCU) on Navistar Straight Trucks Revised 1 Technical 09-18 Bulletin Hazard Alert Messages Read and observe
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W155-5 CHRYSLER 8 3 /4" & 9 3 /4" REAR AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time
More informationBRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM
Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the
More informationTH!NK neighbor Section 2 Chassis Section 2 Chassis
General Specifications... 2 Torque Specifications... 2 Description and Operation... 4 Wheel Alignment Angles... 4 Brakes... 4 Diagnosis and Testing... 6 Ball Joint Inspection... 6 Wheel Bearing Inspection...
More informationFerrari 328 Standard Brake System Bleed/Flush (Non-ABS)
Ferrari 328 Standard Brake System Bleed/Flush (Non-ABS) Carl Rose December 2003 Annual brake fluid replacement is recommended as routine system maintenance (more frequently if car driven vigorously) or
More information2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
More information67-69 Camaro. Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning
67-69 Camaro Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning These instructions are for hydraulic master cylinder installations using an external
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationASSEMBLY INSTRUCTIONS FOR PART NUMBER GROUP
ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HAT KIT, 1.19 DIAMETER VENTED ROTOR 1990-005 ACURA/CIVIC ( LUG) 000-003 CIVIC SI ( LUG) 007 - PRESENT HONDA FIT FOR FACTORY 6 mm DISC SPINDLE PART NUMBER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take
More informationREV F2.0. User's Manual. Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28
REV F2.0 User's Manual Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28 Table of Contents INTRODUCTION...4 Starting TOOLBOX Software... 5 MAIN MENU...6 System Setup... 6 Language... 7 Select
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-3 1988-98 CHEVY K1500 4WD 10" DRUMS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationSECTION 4A HYDRAULIC BRAKES
SECTION 4A HYDRAULIC BRAKES CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT CHEVROLET CORVETTE
ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT 965-98 CHEVROLET CORVETTE PART NUMBER GROUP 40-857 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED
More informationGROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-3 BASIC BRAKE SYSTEM DIAGNOSIS 35A-6 HYDRAULIC BRAKE BOOSTER (HBB) DIAGNOSIS...
35A-1 GROUP 35A CONTENTS GENERAL DESCRIPTION......... 35A-3 DIAGNOSIS 35A-6 INTRODUCTION..................... 35A-6 DIAGNOSTIC TROUBLESHOOTING STRATEGY......................... 35A-6 SYMPTOM CHART...................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Disc Brake Spindle Kit SUM-BKA2447 1964-72 A-BODY 1967-69 F-BODY 1968-74 X-BODY Thank you for choosing SUMMIT RACING for your braking needs. Please take the time to read and carefully
More informationASE Practice Test A5 Brakes
ASE Practice Test A5 Brakes Hydraulic System Diagnosis and Repair 1) A spongy brake pedal may be caused by: a. ABS Diagnostic Trouble Code set b. Frozen caliper piston c. Defective metering valve d. Air
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationSAGINAW P-SERIES PUMP INSTALLATION
SAGINAW P-SERIES PUMP INSTALLATION WARNING Failure to read and follow these instructions will void any warranty, can cause severe damage to power steering components and premature failure. Pump internals
More informationInstallation Guide. Installing the FRK Hydraulic Compact Unit (HCU) on International School Buses TP-0913 Issued 1 Technical Bulletin
Issued 12-08 Installation Guide Installing the FRK 08-10086 Hydraulic Compact Unit (HCU) on International School Buses Issued 1 Technical 12-08 Bulletin Hazard Alert Messages Read and observe all Warning
More informationPlease Read Instructions Completely Before Starting Your Installation QTY. PART NO. DESCRIPTION
INSTRUCTIONS 916-31926 Master Cylinder and Pedal Assembly Speedway Motors, Inc. 2015 Master Cylinder and Pedal Assembly Model T Model A, and '32 Fords The master cylinder is suitable for 4-wheel disc or
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS POWER FRONT DISC CONVERSION KIT A126-7 1963-66 CHEVY C10 PICKUP NON-POWER FRONT DISC CONVERSION KIT A126-8 1963-72 CHEVY C10 PICKUP Thank you for choosing STAINLESS STEEL BRAKES
More informationCopyright 1998 Inter-Industry Conference On Auto Collision Repair v.4.0
Uniform Procedures For Collision Repair BR11 Brakes 1. Description This procedure describes repair, replacement, and inspection requirements for collisiondamaged brake systems. 2. Purpose The purpose of
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More informationINSTALLATION GUIDE. RMS510, 511, 512, 513, 511MC 510-OR, 512-OR Manual Revision:
REKLUSE MOTOR SPORTS z-start Dual-Actuated Brake Kit INSTALLATION GUIDE RMS510, 511, 512, 513, 511MC 510-OR, 512-OR 196-210 Manual Revision: 051309 2002-2009 Rekluse Motor Sports Rekluse Motor Sports,
More informationTech Feature: Brake Job on Ford Edge
Tech Topics Tech Feature: Brake Job on Ford Edge By Andrew Markel email Editor, Brake & Front End Magazine August 20, 2010 The Ford Edge is an SUV based on a the CD3 platform. The brakes on these vehicles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-3 1965-72 GM A-BODY 10 & 12 BOLT AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationANTI-LOCK BRAKE SYSTEM - REAR WHEEL
ANTI-LOCK BRAKE SYSTEM - REAR WHEEL 1994 Nissan Pickup 1994 BRAKES Nissan - Rear Anti-Lock Pathfinder, Pickup DESCRIPTION In 2WD mode, Rear Anti-Lock Brake System (RABS) helps the driver to maintain steering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS
More informationBRAKE FLUID BLEEDING. 1. PREPARE FOR BLEEDING a. Move the shift lever to the P position and apply the parking brake.
BRAKE FLUID BLEEDING CAUTION: Bleeding without the intelligent tester may result in the air not being completely bled. As this can result in an accident, be sure to use the intelligent tester for air bleeding.
More informationASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH DIAMETER VENTED ROTOR - RACE
www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH 11.75 DIAMETER VENTED ROTOR - RACE 00 - PRESENT BMW MINI COOPER AND MINI COOPER S PART NUMBER GROUP 10-870 DISC BRAKES SHOULD
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationOVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.
OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become
More informationSERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS
SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SAFETY PROCEDURES Always follow the vehicle manufacturer's recommended safety procedures in your Shop and Owners Manual. REQUIRED TOOLS Flat blade screwdriver,
More information1993 AEROSTAR, BRONCO, EXPLORER, F SERIES, F-47, RANGER
CLUTCH SOFT UNRESPONSIVE CLUTCH Article No. PEDAL AIR ENTRAPPED IN HYDRAULIC 93-12-19 SYSTEM SERVICE TIPS CLUTCH HYDRAULIC UNABLE TO RELEASE AIR ENTRAPPED IN SYSTEM SERVICE TIPS CLUTCH HYDRAULIC BLEED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationBrakeVac EBB1000 Brake Service System
MOTORVAC TECHNOLOGIES INC. BrakeVac EBB000 Brake Service System Operator Manual PDF VERSION 200-8342 EBB 000 BRAKEVAC Why should the Brake system be Flushed? Brake fluid is hygroscopic meaning it can absorb
More informationGROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-3 BASIC BRAKE SYSTEM DIAGNOSIS 35A-4 SPECIAL TOOLS... 35A-16 BRAKE PEDAL...
35A-1 GROUP 35A CONTENTS GENERAL DESCRIPTION......... 35A-3 DIAGNOSIS 35A-4 INTRODUCTION TO DIAGNOSIS........................ 35A-4 DIAGNOSTIC TROUBLESHOOTING STRATEGY...... 35A-4 SYMPTOM CHART...................
More informationSECTION 4A HYDRAULIC BRAKES
SECTION 4A HYDRAULIC BRAKES Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationAssignment 3 Hydraulic Brake Systems
Name(s) Assign_3_Hydraulics Assignment 3 Hydraulic Brake Systems BE SURE TO SAVE THIS FILE before, during and after completing your work. (Hint if you write your name, then save and close this, your name
More informationOil Injection System
Chapter Thirteen Oil Injection System This chapter provides removal, inspection and installation instructions for all oil injection components. Air bleeding instructions are also provided. Refer to Chapter
More informationLEXUS IS 250 Front Performance Brake Kit Section I - Installation Preparation
LEXUS IS 250 Front 2006- Performance Brake Kit Section I - Installation Preparation Part Number: PTR09-53080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH
More informationBrake Bleeder Kit and Vacuum/Pressure Pump
PART NUMBER 119-020 800.500.1500 mamotorworks.com Brake Bleeder Kit and Vacuum/Pressure Pump WARNING! These pumps are not approved for use with combustible materials such as gasoline, kerosene or diesel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationPower Steering Pump. GM Century/Lumina/Grand Prix/Intrigue REMOVAL & INSTALLATION BLEEDING
1 of 9 GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Power Steering Pump REMOVAL & INSTALLATION BLEEDING When servicing the power steering pump, inspect the power steering fluid. Look for foaming, milky
More informationInstallation Instructions
Replacement Proportioning Valve for BrakeMaster model 9060 Installation Instructions Part number 900001 Time Tested Time Proven ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 800-669-9690 Fax
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationVolkswagen Golf > VW Rabbit GTI 2006-> (A5)
Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> (A5) Allocation of PR. No. for brakes The brake system installed in a vehicle is documented on the vehicle data sticker via the relevant PR number. Example
More information1994 Mazda MX-5 Miata. ANTI-LOCK BRAKE SYSTEM 1994 BRAKES Mazda - Anti-Lock
ANTI-LOCK BRAKE SYSTEM 1994 BRAKES Mazda - Anti-Lock DESCRIPTION The Anti-Lock Brake System (ABS) control unit senses reductions in front and rear wheel speed and modulates hydraulic pressure to the brakes
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II
ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH 0.75 DIAMETER SOLID ROTOR 97-978 PINTO / MUSTANG II (FIVE LUG CONFIGURATION ONLY)* PART NUMBER GROUP 0-03-B DISC BRAKES SHOULD ONLY BE INSTALLED
More informationASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH DIAMETER VENTED ROTOR CHEVROLET C-4 CORVETTE
ASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH 1.00 DIAMETER VENTED ROTOR 1988-1996 CHEVROLET C-4 CORVETTE PART NUMBER GROUP 140-8314 DISC BRAKES SHOULD ONLY BE INSTALLED
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationVolkswagen New Beetle Brake System ABS, ABS/EDL 45 Anti-lock Brake System (ABS) (Page GR-45)
45 Anti-lock Brake System (ABS) (Page GR-45) Anti-lock brake system (ABS) and anti-lock brake system with electronic differential lock (ABS/EDL) ITT Mark 20 IE Differences between ABS ITT Mark 20 IE and
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationINSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT
INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you
More informationSUBJECT: Front Brake Pulsation During Light To Moderate Brake Application
NUMBER: GROUP: DATE: 05-003-02 REV. B Brakes Dec. 16, 2002l This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationSERVICE BRAKES GROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-2 BRAKE PEDAL... 35A-22 BASIC BRAKE SYSTEM DIAGNOSIS 35A-3
35A-1 GROUP 35A CONTENTS GENERAL DESCRIPTION 35A-2 BASIC BRAKE SYSTEM DIAGNOSIS 35A-3 INTRODUCTION TO BASIC BRAKE SYSTEM DIAGNOSIS 35A-3 BASIC BRAKE SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY 35A-3 SYMPTOM
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (. OFFSET) 005 - PRESENT MUSTANG 8.8 (5 LUG) PART NUMBER GROUP 0-98 INSTALLATION OF THIS KIT SHOULD ONLY
More informationMOTORVAC. BrakeVac-II. MODEL NUMBER Brake Fluid Service System. Operator Manual MotorVac
MOTORVAC BrakeVac-II MODEL NUMBER 500-800 Brake Fluid Service System Operator Manual Why should the Brake system be Flushed? Brake fluid is hygroscopic meaning it can absorb moisture from the air resulting
More information2010 Toyota Prius Repair Manual
REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1995 Chevrolet Tahoe 1995 BRAKES General Motors Corp. - Anti-Lock - 4WAL Chevrolet: Pickup, Tahoe GMC: Sierra, Suburban, Yukon MODEL IDENTIFICATION Vehicle model can be identified
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS A112, A112-1 & A112-93 1979-93 FORD MUSTANG with 7.5" & 8.8" AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KIT A120-20, A120-21 1964 1 /2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationBrakeVac-II Brake Fluid Service System
BrakeVac-II Brake Fluid Service System Part No. 500-800/500-805 USER MANUAL 500-800 (Serial Numbers 800-200 and up) 500-805 (Serial Numbers 805-0700 and up) 324 Blundell Rd. Mississauga ON Tel. 905.65.8620
More informationINSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) , , , ,
INSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) 260-3372, 260-3374, 260-3376 260-3378, 260-3380, 260-5920 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT
More informationBLEEDING; 2007 MY PRIUS [08/2...
BLEEDING; 2007 MY PRIUS [08/2... Last Modified: 11 22 2013 6.6 N Doc ID: RM000001XYG001X Model Year: 2007 Model: Prius Prod Date Range: [08/2006 ] Title: BRAKE: BRAKE FLUID: BLEEDING; 2007 MY Prius [08/2006
More informationText in Illustration
ON-VEHICLE INSPECTION If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS SUM-BK1329-X, SUM-BK1329-99904, SUM-BK1330-X, SUM-BK1330-99904 CHRYSLER 8 3 /4", 9 3 /4" and 2-PIECE REAR AXLES Thank you for choosing SUMMIT RACING
More informationP/N Instr Rev Page 1 of 11
BRAKE AND CLUTCH KIT P/N 2883864 IMPORTANT Due to the technical nature of this kit, Indian Motorcycle insists this installation be performed by a certified Indian Motorcycle Technician. APPLICATION Verify
More informationON-VEHICLE SERVICE
1- CLUTCH General Information/Service Specifications/ Lubricants/On-vehicle Service GENERAL INFORMATION 110001009 The clutch is a dry single-disc, diaphragm type; hydraulic pressure is used for the clutch
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More information