Belt Changing Instructions Top View :Belts attached and alignment view Undue wear / belt replacement is normally caused by 2 problems. The first probl

Size: px
Start display at page:

Download "Belt Changing Instructions Top View :Belts attached and alignment view Undue wear / belt replacement is normally caused by 2 problems. The first probl"

Transcription

1 Ksys1 Conveyor Manual Belt Changing Instructions

2 Belt Changing Instructions Top View :Belts attached and alignment view Undue wear / belt replacement is normally caused by 2 problems. The first problem is applying to much force to make the product move through the conveyor. Minimum tension should be used. The second problem is overtightening of belt on conveyor itself. The distance between belt and belt guide should be minimal. Overtightening will cause 1. Excessive belt wear, 2. possible idler damage and 3. motor damage. Belt Guide Belt Minimal distance Tension Block Assembly To Tension the belt. To Tension belt. Loosen locking nut. Turn tension bolt counter- clockwise to increase tension. Adjust tension so there is minimal distance between back of belt and belt guide. Retighten locking nut. NOTE: LOCKING NUT AND TENSION BOLT ARE LEFT-HANDED THREAD. I.E. TO TIGHTEN, TURN CCW TO LOOSEN TURN CW.

3 Top View : Motor and belts not shown Undue wear or belt replacement is normally caused by 2 problems. The first problem is applying to much force to make the product move through the conveyor. Minimum tension should be used. The second problem is overtightening of belt on conveyor itself. The belt should sit against the belt guide with minimal distance between them. Overtightening will cause 1. belt wear, 2. possible idler damage and 3. motor damage. Changing Idler Pulley Assembly Instructions When Changing Idler pulley 1. Remove Old Idler pulley. 2. Clean slot (Both Top and Bottom) 3. Apply new grease (supplied) 4. Install new idler pulley 5. Slide idler assembly back and forth in slot to ensure smooth movement NOTE: Top of Idler Pulley is Marked with a "Top". "Top"goes to top plate. Idler pulley needs to be "pushed down" to bushing before tensioning belt Idler Pulley should be horizontal to timing pulley. If it is not, belt wear and possible damage to belts, motor and idler pulley WILL OCCUR. To much tension on belt will cause this to happen. Use Minimum pressure to hold product Idler Belt Pulley Timing Belt Pulley Idler Belt Pulley Timing Belt Pulley Both Idler pulley and timing belt pulley should be parallel to each other

4 TO REMOVE OLD BELT 1. Loosen belt tensioner. (# 8) may be [LEFT -HANDED THREAD] 2. Remove screws from locations 1-7 STARTING with #5 NOTE: SCREW # 5 is attached to BOTTOM PLATE 3. Seperate plates from each other 4. Install new belt 5. Adjust tension on belt 6. Reinstall plates and screws. Starting with # 5. Make sure the idler pulley is in the slot (# 9) and belt is to the outside of belt guide (# 10) 7. Make final tension adjustment on belt (# 8) KH Systems Inc S. Rancho Way Suite 202 Rancho Dominguez CA Phone: Fax: bottomcoding@aol.com Web:

5 Breakdown of Conveyor System Top Plate Left Side Part Number 40002

6 Motor Right Side, Part Number 40019, Motor includes wiring. Motors are interchangeable with each other Ksys1 Conveyor Front view Ksys1 Conveyor Side View

7 Plate Assembly

8 Carrier Assembly

9 Product Plate and Micro-adjuster

10 Frame Assembly

11 Product Detect Assembly

12 Product Detect Assembly

13 Product Detect Assembly

14 How to make adjustments on Ksys1 conveyor system. 1. Adjusting carrier to Product. A. Loosen handles on carrier. B. With both hands push or pull (depending on increasing or decreasing the distance between the carriers) the carrier with fingers. This must be done at the same time to avoid misalignment of carrier. Do not try to push plates. This will misalign the carrier on the rod, making it much more difficult to move. C. Relock handles on carrier ** Note: When setting distance for product, it is best to place 1 product at one each end of conveyor and adjust accordingly, using minimal tension to hold the product in place. If there is too much pressure, the following problems might occur. 1. Movement of belt guide. 2. Stoppage of motors from turning

15

16

17

18

19

20

21

22

23

24

25

26

27

GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions

GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation

More information

62 Deck Idler Kit High Speed

62 Deck Idler Kit High Speed Part No. 00 FORM NO. -899 6 Deck Idler Kit High Speed For Model 70 Serial No. 99000 to 99000 For Model 7 Serial No. 9900 to 99000 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify

More information

TABLE OF CONTENTS. Ram Assembly

TABLE OF CONTENTS. Ram Assembly TABLE OF CONTENTS DUC Cover------------------------------------------------------------------------------------ 00 Table of Contents----------------------------------------------------------------------------

More information

Perfmaster Air V3. Serial Number. Date

Perfmaster Air V3. Serial Number. Date Perfmaster Air V3 12-2015 Serial Number Date TABLE OF CONTENTS SPECIFICATIONS.3 SAFETY PROCEDURES/CARE & MAINTENANCE..4 COMPONENT IDENTIFICATION 5 DELIVERY TRAY ASSEMBLY.6 PAPER STOP ASSEMBLIES..7 MACHINE

More information

Timing Belt: Service and Repair

Timing Belt: Service and Repair 2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata

More information

Models Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE

Models Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE Propane Belt Squeal Models Affected: Visions with Propane Engines ISSUE Front End Accessory Drive (FEAD) Belt chirping/squealing caused by improper fore-aft crankshaft pulley positioning. CORRECTIVE ACTION

More information

Instructions for changing bearings on all B&C Technologies SP and HP models

Instructions for changing bearings on all B&C Technologies SP and HP models Instructions for changing bearings on all B&C Technologies SP and HP models Tools and material required: 30 mm socket Socket handle with extension or air impact wrench Regular Screwdriver Phillips head

More information

Looking up the front of the engine from under the radiator. (Picture taken with belt under tension.)

Looking up the front of the engine from under the radiator. (Picture taken with belt under tension.) 8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then

More information

READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLATION

READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLATION Conveyor Idler Installation and Operation Manual Short Term Storage If conveyor idlers are to be stored for an short period(less than 3 months) prior to installation, the following steps should be taken.

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

Service Bulletin. Premature Drive Belt Wear

Service Bulletin. Premature Drive Belt Wear Premature Drive Belt Wear Applies to: E-TRx Tools Required Washers 120 grit sand paper Adjustable Wrench ¼ Hex key 4mm Hex key Steel Square 12 Steel Square 90 degree Symptom Drive belt is damaged (Fig.

More information

Belt Tracking Manual. K-Trough Trainer. 1 P age. Issue:

Belt Tracking Manual. K-Trough Trainer. 1 P age. Issue: K-HD Polyurethane Guide Roller K-Self Centring Idler K-MTD Disc Tracker K-Trough Trainer 1 P age Section 1: Rule Zero and Set-Up 1.1 Identify areas along the conveyor, which are suffering from misalignment.

More information

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission

More information

Engine, disassembly and

Engine, disassembly and Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move

More information

Timing Belt Replacement

Timing Belt Replacement 2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing

More information

Installation and Operation Manual. Manufacturers of Innovative Materials Handling Equipment since 1957.

Installation and Operation Manual. Manufacturers of Innovative Materials Handling Equipment since 1957. SWINGSET DISTRIBUTOR Installation and Operation Manual Manufacturers of Innovative Materials Handling Equipment since 1957. 491 North Emerson Street * Cambridge MN 55008-1316 U.S.A. Toll Free (800) 328-8002

More information

SY-SERIES S04DA75 THRU S06DA180 & S04SR75 THRU S06SR180 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS

SY-SERIES S04DA75 THRU S06DA180 & S04SR75 THRU S06SR180 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS SY-SERIES S04DA75 THRU S06DA180 & S04SR75 THRU S06SR180 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS INTRODUCTION A-T Controls SY scotch yoke actuators have been designed and engineered to provide

More information

Crestline Dampening System. Installation Instructions. Hamada RS34 & VS34 Satellite Unit. For Presses Originally Equipped With. Integrated Dampeners

Crestline Dampening System. Installation Instructions. Hamada RS34 & VS34 Satellite Unit. For Presses Originally Equipped With. Integrated Dampeners Crestline Dampening System Installation Instructions Hamada RS34 & VS34 Satellite Unit For Presses Originally Equipped With Integrated Dampeners X88-113 01/2001 Rev-A GENERAL INFORMATION ATTENTION CRESTLINE

More information

MAINTENANCE - LPX PORTABLE TREATER

MAINTENANCE - LPX PORTABLE TREATER MAINTENANCE - LPX PORTABLE TREATER Proper maintenance of the Portable LPV Treater is critical for peak performance, reliability and accuracy of this system. The following is a guideline for the type of

More information

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks

More information

SE-1200-MP ECO - SERIES

SE-1200-MP ECO - SERIES Inc. SE-1200-MP ECO - SERIES Operation & Parts Manual SE 1200 MP ECO -SERIES OWNERS MANUAL Table of Contents 1. Installation guide 2. Set-up instructions 3. Operation instructions 4. Cleaning 5. Troubleshooting

More information

3. Timing Belt 2-3 SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER

3. Timing Belt 2-3 SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER SERVICE PROCEDURE 2-3 A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER G2M0107 1) Remove V-belt and A/C belt tensioner. 2) Remove pulley bolt. To lock crankshaft use ST. ST 499977000 CRANKSHAFT PULLEY WRENCH

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

Rear Roller Brush Kit Greensmaster 3150 & 3250

Rear Roller Brush Kit Greensmaster 3150 & 3250 Rear Roller Brush Kit Greensmaster 50 & 50 Model No. 04640 Model No. 0464 Form No. 8 808 Rev. B Installation Instructions Note: The Rear Roller Brush Kit can only be installed on cutting unit models 0460

More information

PARTS LIST. Alternator Bracket A Main Alternator Bracket 1-P763-A... Idler Pulley. Pulleys. 5/16 x 7/8 SHCS (P/S Option)

PARTS LIST. Alternator Bracket A Main Alternator Bracket 1-P763-A... Idler Pulley. Pulleys. 5/16 x 7/8 SHCS (P/S Option) LS Custom Series Serpentine Kit LS Alternator & Air Conditioning Only Serpentine Kit Kit # 20090-08 LS Alternator, Air Conditioning & Power Steering Serpentine Kit Kit # 20095-08 11/10/16 PARTS LIST Alternator

More information

Polaris 340 & ATV Power Module Training and Troubleshooting Guide

Polaris 340 & ATV Power Module Training and Troubleshooting Guide Polaris 340 & ATV Power Module Training and Troubleshooting Guide Summary: This guide is intended as a training tool for the mechanical evaluation and troubleshooting of a 340 or ATV power module only.

More information

CenterLine Filter Wheel

CenterLine Filter Wheel Engineering Excellence Because Your Image Depends On It User s Guide CenterLine Filter Wheel Finger Lakes Instrumentation, LLC September 2014 WELCOME Thank you for purchasing an FLI CenterLine Filter Wheel.

More information

Timing Belt: Service and Repair

Timing Belt: Service and Repair 1996 Honda Accord Sedan L4-2.2L SOHC (16 Valve) Copyright 2009, ALLDATA 9.90 Page 1 Timing Belt: Service and Repair TIMING BELT AND TIMING BALANCER BELT REMOVAL Timing Components NOTE: - Turn the crankshaft

More information

ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal

ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft

More information

TABLE OF CONTENTS INSTALLATION & OPERATING INSTRUCTION MANUAL FOR MODEL PRC-- POWER ROLLER CONVEYOR

TABLE OF CONTENTS INSTALLATION & OPERATING INSTRUCTION MANUAL FOR MODEL PRC-- POWER ROLLER CONVEYOR TABLE OF CONTENTS INSTALLATION & OPERATING INSTRUCTION MANUAL FOR MODEL PRC-- POWER ROLLER CONVEYOR 1. INSTALLATION 2 1.1. GENERAL INSTALLATION 2 1.1.1. Building Connections 3 2. OPERATION 3 2.1. GENERAL

More information

Sure-Feed Engineering Inc. SE-900-EI. Operation & Parts Manual

Sure-Feed Engineering Inc. SE-900-EI. Operation & Parts Manual . SE-900-EI Operation & Parts Manual SE 900 EI OWNERS MANUAL Table of Contents 1. Installation guide 2. Set-up instructions 3. Operation instructions 4. Cleaning 5. Troubleshooting 6. Parts manual 7. Electrical

More information

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS June 2004 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Please be sure that this document is given to the end user of this product. It contains many important items relating to the proper usage of

More information

Installation Manual for VHM-25 Series Arms Channel Mount

Installation Manual for VHM-25 Series Arms Channel Mount 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual

More information

Ford 6.8L, w/spider, 2000+

Ford 6.8L, w/spider, 2000+ DewEze Aiir Compressor Kiit 700554 Ford 6.8L, w/spider, 2000+ INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Drain the radiator. 3. Remove the air cleaner assembly. 4. Remove the upper radiator

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS

THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS INTRODUCTION A-T Controls THD scotch yoke actuators have been designed and engineered to

More information

2003 Hyundai Truck Santa Fe V6-3.5L

2003 Hyundai Truck Santa Fe V6-3.5L Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the

More information

TIMING BELT TENSIONER FOR AFTERMARKET TENSIONER P/N FORD U.K. 1.8L 4-Cyl. Diesel Revision date: 06/17/1999

TIMING BELT TENSIONER FOR AFTERMARKET TENSIONER P/N FORD U.K. 1.8L 4-Cyl. Diesel Revision date: 06/17/1999 1. Failure to set belt tension correctly to this procedure will result in premature engine failure! 2. The Auto-tensioner is a thermal expansion compensation device so tensioning should only be carried

More information

V6 Spring Belt Tensioner

V6 Spring Belt Tensioner Dodgerunner s V6 Spring Belt Tensioner Installation Guide Dodgerunner 2007 The bracket consists of two pieces of 1/8" steel bolted together. The main piece is flat plate with welded-on alternator mounting

More information

Chrysler Mid Mount A/C Kit

Chrysler Mid Mount A/C Kit 08/29/16 Chrysler 318-360 Mid Mount A/C 40490 Kit PARTS LIST 40491 Alternator & A/C Bracket 1-40491-A... Alt-A/C Front Main Bracket 1-40491-B... Alt-A/C Rear Support Bracket 1-20140-A... Alternator Re-Locator

More information

CVVT Hub Change Guide P2 Vehicles, Rev.2 Compiled by F250 with input from MANY others

CVVT Hub Change Guide P2 Vehicles, Rev.2 Compiled by F250 with input from MANY others Important information: CVVT Hub Change Guide P2 Vehicles, Rev.2 VIDA instructions may not have the correct information with regards to clockwise (CW) or counterclockwise (CCW) movements when setting the

More information

SCAMP AND UTILITY MODELS SELF-PROPELLED BELT DRIVE SERVICING 4502, 4503, 8602, 8603 WITH F SERIES ENGINES

SCAMP AND UTILITY MODELS SELF-PROPELLED BELT DRIVE SERVICING 4502, 4503, 8602, 8603 WITH F SERIES ENGINES 4502, 4503, 8602, 8603 WITH F SERIES ENGINES Adjustments and servicing of the Scamp and Utility self-propelled mowers are very different from all previous models of self-propelled mowers. BEFORE ANY ADJUSTMENTS

More information

WOOD CHIPPER WC1105 5PQ (8/08/2012)

WOOD CHIPPER WC1105 5PQ (8/08/2012) O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1105 5PQ990102 (8/08/2012) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the

More information

#92 DISC BRAKE ADJUSTMENTS # BRAKE MONITOR

#92 DISC BRAKE ADJUSTMENTS # BRAKE MONITOR #92 DISC BRAKE ADJUSTMENTS #102-091 BRAKE MONITOR Page 1 of 11 HOLLISTER-WHITNEY DISC BRAKE WITH BRAKE MONITOR ADJUSTMENT PROCEDURE Page 2 of 11 HOLLISTER-WHITNEY DISC BRAKE WITH MONITOR SWITCH ADJUSTMENTS

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.

More information

LS Style Track Alt/AC Serpentine Kit Kit # (Standard Mount Electric Throttle Body Kit) Kit # (Narrow Mount Mechanical Throttle Body Kit)

LS Style Track Alt/AC Serpentine Kit Kit # (Standard Mount Electric Throttle Body Kit) Kit # (Narrow Mount Mechanical Throttle Body Kit) 12/08/16 LS Style Track Alt/AC/PS Serpentine Kit Kit # 20060 (Standard Mount Electronic Throttle Body Kit) Kit # 20065 (Narrow Mount Mechanical Throttle Body Kit) LS Style Track Alt/AC Serpentine Kit Kit

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

Service and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference

Service and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference 1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,

More information

Ford 9 XD Aussie-Locker Install Instructions.

Ford 9 XD Aussie-Locker Install Instructions. Ford 9 XD-45831 Aussie-Locker Install Instructions. Before the install check the following. 1. Must be 31 spline 4-pinion carrier. 2. Must be an open carrier not a limited slip. 3. Refer to Ford or vehicle

More information

Please try our way first.

Please try our way first. 1958-1962 Corvette Raingear installation instructions Designer s Note: The 1958-1962 Corvette RainGear wiper system that you have purchased is complex and will require patient fitting. Complete Instructions

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Read the complete assembly instructions before starting the assembly. You should have: - one mower deck assembly - two carrier arm assemblies - two rear tire assemblies - one ATV

More information

OPERATIONS & MAINTENANCE MANUAL KENNETH WALKER OBSERVATORY AT DEMIGUEL ELEMENTARY SCHOOL

OPERATIONS & MAINTENANCE MANUAL KENNETH WALKER OBSERVATORY AT DEMIGUEL ELEMENTARY SCHOOL OPERATIONS & MAINTENANCE MANUAL KENNETH WALKER OBSERVATORY AT DEMIGUEL ELEMENTARY SCHOOL Department of Mechanical Engineering April 23, 2010 1 TABLE OF CONTENTS Dome Rotation Overview... 3 Maintenance...

More information

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5 Install Headlight (900, 0, 05) (Figure 5). Remove headlight from location under dash panel. Keep nut for installation.. Attach headlight to bolt on right side of the dash. Fasten with nut removed in step..

More information

Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount

Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount Install Time: 20-30

More information

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 8 Rev A Wheel Horse Snowthrower for 5xi Lawn and Garden Tractors Model No. 7966 890050 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information

More information

FOR SIT-STAND WORKSTATION

FOR SIT-STAND WORKSTATION INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3

More information

MSI SINGLE IDLER BELT SCALE

MSI SINGLE IDLER BELT SCALE MSI SINGLE IDLER BELT SCALE Instruction Manual PL-319 January 2001 33453190 Rev. 1.2 Safety Guidelines Warning notices must be observed to ensure personal safety as well as that of others, and to protect

More information

Operation and Maintenance Manual for BS and BH Hydraulic Torque Wrenches

Operation and Maintenance Manual for BS and BH Hydraulic Torque Wrenches BOLTORQ Operation and Maintenance Manual for BS and BH Hydraulic Torque Wrenches It is operating manual of BS series and BH series wrenches, please read carefully and follow the instructions. Warning and

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.

More information

Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal

Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal TM Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal WARNING This Special Instruction Manual and General Instructions Manual, CA-1, should be read

More information

2106 HDCT-DUAL Belt Tracker

2106 HDCT-DUAL Belt Tracker 2106 HDCT-DUAL Belt Tracker Features Stainless steel construction Two cylinders for added tracking power and neutral positioning External bearings Two mechanical remote sensors Filter regulator unit Tracker

More information

MMU2 filament jam. MMU2 filament jam. Written By: Jakub Dolezal manual.prusa3d.com/ Page 1 of 7

MMU2 filament jam. MMU2 filament jam. Written By: Jakub Dolezal manual.prusa3d.com/ Page 1 of 7 Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 7 Step 1 Filament jam During filament loading or unloading the filament can get stuck (jammed). The printer will try several times to fix it

More information

AUTOMATIC SPINDLE CAPPER

AUTOMATIC SPINDLE CAPPER OPERATIONS MANUAL AUTOMATIC SPINDLE CAPPER (Shown above in one of several configurations.) 3999 East Hupp Road, Bldg. R-43 Phone: 219-393-3600 La Porte, IN 46350 Fax: 219-393-5260 www.liquidpackagingsolution.com

More information

Installation instructions for the FC6 Forward Controls for Suzuki Marauder 800

Installation instructions for the FC6 Forward Controls for Suzuki Marauder 800 Installation instructions for the FC6 Forward Controls for Suzuki Marauder 800 It is highly recommended that you use a thread lock compound such as Loctite on all threads to keep them from vibrating loose.

More information

NEW WAVE 3 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS. with Quad Spring Tensioners

NEW WAVE 3 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS. with Quad Spring Tensioners NEW WAVE 3 with Quad Spring Tensioners INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Check us out at www.asgco.com Customer Service 800-344-4000 800-394-2358 ASGCO Mfg., Inc. 301 Gordon Street Allentown,

More information

Belt Drive Preventive Maintenance Manual

Belt Drive Preventive Maintenance Manual VAC VAC VAC VAC VAC VAC Belt Drive Preventive Maintenance Manual VAC Belt Drive Preventive Maintenance Manual Preventive Maintenance Saves Time & Money Compared to the mechanical problems and costs incurred

More information

When to Turn Pins and Bushings

When to Turn Pins and Bushings When to Turn Pins and Bushings 1. The track pins and bushings must be turned when the OD of the bushings is less than 2.11 inches (54 mm). TRACK PINS AND BUSHINGS 5506-5 5. Look for the wear point on the

More information

Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal

Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal TM Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal WARNING This Instruction Manual and General Instructions Manual, CA-1, should be read thoroughly prior to pump installation,

More information

HercuLine 2000 Series Gear Kit Replacement Instructions

HercuLine 2000 Series Gear Kit Replacement Instructions HercuLine 2000 Series Gear Kit Replacement Instructions 51452443-501 Document Information Form: 62-86-33-35 Effective: 5/04 Supersedes: None Summary This kit contains all the gears, idler shafts and hardware

More information

Timing Belt: Service and Repair TIMING BELT

Timing Belt: Service and Repair TIMING BELT 2003 Hyundai Truck Santa Fe V6-2.7L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT TIMING BELT 2.7L REMOVAL 1. Remove the engine cover. 2. Using a [16 mm], rotate the

More information

!" # )("*"+,$' 0*.!0&!&1* &23# 0 &*&.444#3# 0

! # )(*+,$' 0*.!0&!&1* &23# 0 &*&.444#3# 0 !" $%$&'( )("*"+,$' -.%%,$' /.%%,+% 0*.!0&!&1* &23 0 &*&.4443 0 INTRODUCTION Dear Customer Congratulations and thank you for purchasing a Powermover by Ultra-Fab. It is our intent to provide you with the

More information

Spicer Axles & Brakes

Spicer Axles & Brakes Spicer Axles & Brakes Wheel Differential Bearing Adjustment Tool Kit Instructions P/N: SHAIS150 Shown below is a complete set of instructions on how to properly utilize Dana s Wheel Differential Bearing

More information

WOOD CHIPPER WC1103 5PQ (8/02/12)

WOOD CHIPPER WC1103 5PQ (8/02/12) O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1103 5PQ990101 (8/02/12) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the

More information

Final Assembly Instructions: Runaround Cruiser

Final Assembly Instructions: Runaround Cruiser Final Assembly Instructions: Runaround Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert

More information

Installation. Check, Test & Start Procedure

Installation. Check, Test & Start Procedure Installation General CAUTION: Sheet metal parts, screws, clips and similar items inherently have sharp edges, and it is necessary that the installer and service personnel exercise caution. The installation

More information

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket. Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,

More information

Final Assembly Instructions Portside Cruiser

Final Assembly Instructions Portside Cruiser Final Assembly Instructions Portside Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert cycling

More information

Page 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft

More information

Procedure Replacing a Cover

Procedure Replacing a Cover Procedure 7.1 - Replacing a Cover Cover Removal 1. Remove two screws, one each side, from the front of the top cover. Remove the top cover. See Diagram 7.1. Diagram 7.1 - RBK 815 Covers Top Cover Left

More information

CABINET REEL OPERATING INSTRUCTIONS

CABINET REEL OPERATING INSTRUCTIONS CABINET REEL OPERATING INSTRUCTIONS MODELS 15, 25, 40 & 60 SERIES RAPID-AIR CORPORATION 4601 KISHWAUKEE ST. ROCKFORD, IL 61109-2925 Phone: (815) 397-2578 Fax: (815) 398-3887 Web Site: www.rapidair.com

More information

INSTALLATION INSTRUCTIONS FOR: RE DOOR JK WRANGLER RE DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM

INSTALLATION INSTRUCTIONS FOR: RE DOOR JK WRANGLER RE DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM RUBICON MANUFACTURING INC. 3290 MONIER CIR., RANCHO CORDOVA, CA. 95742 916-473-4600 INSTALLATION INSTRUCTIONS FOR: RE7122 2 DOOR JK WRANGLER RE7142 4 DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM Safety

More information

LIGHT BALL CLUTCH Lifelong Engineering and Development, Inc.

LIGHT BALL CLUTCH Lifelong Engineering and Development, Inc. Lifelong International Bowling, Inc. Worlds Leader in High Performance Specialty Parts LL300-202 Instructions LIFELONG INTERNATIONAL BOWLING, INC. LIGHT BALL CLUTCH Your new LIGHT BALL CLUTCH is designed

More information

Service Manual Notes... iii. Tools Needed... v Parts:... v Technical Help... v Additional Notes... v. 1. Machine Overview Covers...

Service Manual Notes... iii. Tools Needed... v Parts:... v Technical Help... v Additional Notes... v. 1. Machine Overview Covers... 5K Service Manual ii Table of Contents Service Manual Notes... iii Tools Needed... v Parts:... v Technical Help... v Additional Notes... v 1. Machine Overview.. 6-7 1.1. Covers...8 2. Drive Train.....9

More information

This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the

This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the box and assemble it. If you have not assembled a bicycle

More information

THE GLIDER 5th Wheel Attachment

THE GLIDER 5th Wheel Attachment April 2007 APPLICATION: INSTALLATION INSTRUCTIONS MODEL NO. 70460 70046 THE GLIDER 5th Wheel Attachment For use on short bed pickup applications US Patent No. 6247720 COMPLETE PARTS LIST Part Description

More information

Carriage Height Calibration

Carriage Height Calibration 979-530-0207 Carriage Height Calibration The purpose of this Service Calibration is to adjust the distance between the Carriage Assembly and the Center Platen. This calibration is necessary in order to

More information

2003 Hyundai Sonata LX

2003 Hyundai Sonata LX TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate

More information

Note: Replace the washer and the spacer above the turgo or the shaft adapter with the spacer above the washer as shown in the following pictures.

Note: Replace the washer and the spacer above the turgo or the shaft adapter with the spacer above the washer as shown in the following pictures. BEARINGS, SERVICE & ASSEMBLY IMPORTANT Bearing maintenance is important. You should replace bearings ONCE PER YEAR or as soon as you notice any looseness from wear. If they are too loose, severe damage

More information

CRESTLINE DAMPENING SYSTEM INSTALLATION INSTRUCTIONS. Ryobi 3302M Itek 3985 A.B. Dick 9985 X /99

CRESTLINE DAMPENING SYSTEM INSTALLATION INSTRUCTIONS. Ryobi 3302M Itek 3985 A.B. Dick 9985 X /99 CRESTLINE DAMPENING SYSTEM INSTALLATION INSTRUCTIONS Ryobi 3302M Itek 3985 A.B. Dick 9985 X88-32 3/99 GENERAL INFORMATION ATTENTION CRESTLINE DAMPENER OWNER Accel Graphic Systems provides parts and service

More information

Aligning the TH-28/480 Series Lower Drive System

Aligning the TH-28/480 Series Lower Drive System January 15, 2003 Page 1 of 12 Aligning the TH-28/480 Series Lower Drive System 1. Purpose: 1. The purpose of this document is to provide additional reference information for aligning the lower drive system

More information

57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Model: MR55H KUNZ ENGINEERING, INC. / MENDOTA, IL / PH (815) /07

57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Model: MR55H KUNZ ENGINEERING, INC. / MENDOTA, IL / PH (815) /07 57 ROUGH CUT OWNER S MANUAL With Assembly Instructions For Model: MR55H KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 1/07 ASSEMBLY INSTRUCTIONS Read the complete assembly instructions

More information

2002 Mitsubishi Montero Limited

2002 Mitsubishi Montero Limited Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components

More information

IMING BELT COMPONENTS REMOVAL

IMING BELT COMPONENTS REMOVAL 1 of 11 11/21/2012 2:21 PM IMING BELT COMPONENTS REMOVAL 1. Remove the wheel of passenger side. 2. Remove the side cover. 3. Remove the engine cover. 4. Disconnect the power steering hose fixing on the

More information

Compressor - Install (E.40.C.31 - F.10.A.15)

Compressor - Install (E.40.C.31 - F.10.A.15) Compressor - Install (E.40.C.31 - F.10.A.15) 1. Set the compressor on its mount and secure into place using the four bolts. Connect the refrigerant suction line (5) and the discharge line (4). Install

More information

Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit

Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit Install Time: 10-15 minutes The

More information

Logo/Company Name 4 w x.75 h. Assembly Instructions. 1) Remove base, back/back bar, pneumatic cylinder, casters/glides, and seat from box.

Logo/Company Name 4 w x.75 h. Assembly Instructions. 1) Remove base, back/back bar, pneumatic cylinder, casters/glides, and seat from box. 8 ) Remove base, back/back bar, pneumatic cylinder, casters/glides, and seat from box. ) Put casters or glides on base. Use pressure to push in (8). ) Slide optional foot ring () over pneumatic cylinder

More information

Read these instructions thoroughly before attempting to install this option.

Read these instructions thoroughly before attempting to install this option. Rewind Option Kit Installation Instructions This kit includes the parts and documentation necessary to install the Media Rewind option into the following printers: 0XiIIIPlus, 0 dpi 0XiIIIPlus, 00 dpi

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Models: MR55T, MR55B & MR55K

57 ROUGH CUT OWNER S MANUAL. With Assembly Instructions For Models: MR55T, MR55B & MR55K 57 ROUGH CUT MR55K MR55B OWNER S MANUAL With Assembly Instructions For Models: MR55T, MR55B & MR55K KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954 1/05 ASSEMBLY INSTRUCTIONS Read the complete

More information