Blohm+Voss Pipe Handling Equipment Special Link Connector Technical Documentation Original instructions

Size: px
Start display at page:

Download "Blohm+Voss Pipe Handling Equipment Special Link Connector Technical Documentation Original instructions"

Transcription

1 Blohm+Voss Pipe Handling Equipment Special Link Connector Technical Documentation Original instructions Manual PN D Rev. 002, May 2012 Blohm + Voss Oil Tools 1

2 GENERAL INFORMATION Warnings and Note WARNING: A warning indicates a definite risk of equipment damage or danger to personnel. Failure to observe and follow proper procedures could result in serious or fatal injury to personnel, significant property loss, or significant equipment damage. NOTE: A note indicates that additional information is provided about the current topics. WARNING: This technical documentation contains instructions on safety, installation, operation and maintenance for the Blohm + Voss Oil Tools tool. It must Improper / Unsafe Use The tool must only be used for the designated purpose. When using the tool, the rated load must never be exceeded. be studied before working with the tool. Intended use of this manual This manual is intended for use by field service, engineering, installation, operation, and repair personnel. Every effort has been made to ensure the accuracy of the information contained herein. Blohm + Voss Oil Tools, will not be held liable for errors in this material, or for consequences arising from misuse of this material. Anyone using service procedures or tools, whether or not recommended by Blohm + Voss Oil Tools, must be thoroughly satisfied that neither personal safety nor equipment safety will be jeopardized. Intellectual property All rights retained. No part of this document may be reproduced in any form (print, photocopy, microfilm or any other procedure) or be processed using an electronic system without written approval of Blohm + Voss Oil Tools. All information contained in this manual is based upon the latest product information available at any time of printing. Dependent on ongoing technical improvements (ISO 9001) Blohm + Voss Oil Tools reserves the right to change the design and specifications without announcement. The values specified in this manual represent the nominal values of a unit produced in series. Slight deviations in the case of the individual devices are possible. NOTE: In the event of problems that cannot be solved with the aid of this manual, please contact one of the addresses listed below. CE Marking The tool complies with the Machinery Directive 98/37/EC and 2006/42/EC For machines containing any hydraulic or pneumatic powered parts, the Directive 94/9/EC Equipment and protective systems in potentially explosive atmospheres applies. The marking is as follows: CE Ex II 2G T5 (hydraulic tools) or CE Ex II 2G T6 (pneumatic tools). Limited Warranty The warranty provided will be void if the tool is either: 1. Repaired or serviced by a service facility which was not authorised by Blohm + Voss Oil Tools. 2. Replacement parts not manufactured by Blohm+Voss Oil Tools are used. 3. Modifications were made to the tool which were not approved by Blohm+Voss Oil Tools. Manufacturer & Agents World wide Blohm + Voss Oil Tools Hermann-Blohm-Straße Hamburg Germany Phone: / /1162 Fax: / oiltools@blohmvoss.com Blohm + Voss Oil Tools, LLC 7670 Woodway, Suite 266 Houston, Texas United States of America Phone: Fax: bvot@blohmvoss.com Premier Sea & Land Pte. Ltd. 1, Scotts Road #19-12 Shaw Centre Singapore Republic of Singapore Phone: Fax: enquiries@mtqpremier.com.sg 2

3 General safety issues WARNING: One should avoid creating ignition sources, like heat, as a result of the use of the tool with other tools or equipment. WARNING: Do not use the tool for any other purpose than given in this document within its specification. WARNING: Failure to conduct routine maintenance could result in equipment damage or injury to personnel. WARNING: Wear personal protection equipment while working with the equipment. WARNING: All warning plates, signs and labels attached to the equipment must be observed. The warning plates, signs and labels must be present on the tool. Do not remove the labels. If they are missing, replacing is mandatory. WARNING: Any modification to the tool carried out without the approval of Blohm + Voss Repair GmbH will void any warranty. WARNING: Using the tool with damaged or worn parts can create serious incidents. WARNING: The company operating the tool is responsible for evaluating safe and proper use of the tool in a hazard analysis. WARNING: The operating company is obligated to issue working instructions for safe use and supervise observance of these working instructions. WARNING: Every Employee, which operates, services, inspects or otherwise involved with the use of the tool in other areas has to ensure, that these actions are done by trained and by an Blohm + Voss Repair GmbH authorized personnel, and should complete regular courses of training, to ensure proper use as well as safe operation, correct maintainance and inspection. WARNING: If necessary, a reasonable, additional supervisor should be appointed during operation. WARNING: Stay away from the tool during operation. In case it is remote operated it may make movements without warning. WARNING: It is not allowed to use any components which are of "non-b+v" origine, or use "non-oem" parts which are not approved by B+V. It will void any warranty and may effect the correct functioning of the tool and it's safety features. 3

4 EC-DECLARATION OF CONFORMITY We, Blohm + Voss Oil Tools Hermann-Blohm-Strasse Hamburg Phone:+49(0) Fax:+49(0) declare that the product Special Link Connectors which is the subject of this declaration, is in conformity with the following standard(s) or normative documents 2006/42/EC: Machinery Directive from 31 December DIN EN ISO : Safety of machinery, part 1 and 2 DIN EN ISO : Safety of machinery, Risk assessment Directive 94/9/EC: Devices and protection systems for intended use in explosive areas DIN EN :2009-7: Non-electrical equipment for use in potentially explosive atmospheres ISO 13535:2002/API 8C: Petroleum and natural gas industries-drilling and production equipment-hoisting equipment Marking: II 2G T6 4

5 TABLE OF CONTENTS Table of contents GENERAL INFORMATION 2 Warnings and Note 2 Intended use of this manual 2 Intellectual property 2 Improper / Unsafe Use 2 Manufacturer & Agents World wide 2 CE Marking 2 Limited Warranty 2 General safety issues 3 EC-DECLARATION OF CONFORMITY 4 TABLE OF CONTENTS 5 1. DESCRIPTION 8 General description 8 Intended use 8 Design Specification 8 Capacity and weight 8 Identification number 9 Temperature range 9 2. INSTALLATION 12 Lifting and Transport 12 Installation restrictions OPERATION 14 Safety 14 Extreme Low Temperature MAINTENANCE & INSPECTION 16 General 16 Deterioration of equipment 16 Records 16 Dismantling 16 Cleaning 16 Inspection Procedure 16 Lubrication 17 Locking of screws 17 Grease Quality 17 Inspection categories acc. to API RP 8B 18 Frequency 18 Periodic inspection 18 Non-periodic inspection 18 Inspection 18 Inspection of Hydraulic/Pneumatic System 18 Critical Load Inspection 19 Dismantling Inspection 19 Inspection check lists 20 Check Category I (Ongoing observation) 21 Check List Category II (Daily) 21 Check List Category III (every 6 months) 21 Check List Category IV (every year) 21 Wear data criteria 22 Bore and Pins 22 Beyond Repair 22 Critical Areas 23 Handling, storage and transport 24 Storage 24 Short term storage after use and less then 3 months 24 Long term storage over 3 months 24 Preserve the tool: Grease all blank surfaces with grease: Cylinders 24 Handling 24 Transport DRAWINGS AND SPARE PARTS 26 Set of B+V Type Special Link Connector 26 Parts list 26 Elevator Link Connector 26 Parts list Parts list Parts list RSP 28 Parts list RSP 28 5 TABLE OF CONTENTS DESCRIPTION INSTALLATION OPERATIONS MAINTENANCE & INSPECTION DARWINGS

6 TABLE OF CONTENTS DESCRIPTION INSTALLATION OPERATIONS MAINTENANCE & INSPECTION DRAWINGS 6

7 DESCRIPTION DESCRIPTION 7

8 1. DESCRIPTION General description Intended use DESCRIPTION Special Link Connector are designed for connecting a set of 3.1/2" 500 sh tons rated Elevator Links to a set of Special Link Connector. The load rating is limited to vertical direction load only. The Special Link Connectors are designed for connecting Elevator links, freely. They are to be used for their designated purpose only. The links are available in 500 sh tons ratings per set. Design Specification Material and manufacturing standard in acc. to API 7k. Capacity and weight Elevator Link Connector PN Size Rated capacity (ton) Weight (kg / lbs) Y 2.3/4" 350 sh tons 335 / 738, Y 3.1/2" 500 sh tons 680 / 1498 Elevator Link Connector PN A B C Y 730 mm 460 mm 270 mm Y 840 mm 540 mm 300 mm A B C 8

9 Identification number Every Elevator link should have an idenification number. This number is stamped near an eye. Temperature range Links Temperature working range ambient * If not otherwise stated in the databook C to + 60 C * - 4 F to 140 F * Improper / Unsafe use The Special Link Connector must only be used for the designated purpose. When using the Special Link Connector, the specificated load must never be exceeded (depending on the rating). DESCRIPTION 9

10 DESCRIPTION 10

11 INSTALLATION INSTALLATION 11

12 2. INSTALLATION Lifting and Transport Lift the Special Link Connectors only at proper Lifting eyes. At Lifting the Special Link Connector make sure it is properly locked and secured. The lifting procedures should be carefully observed! Installation restrictions The Special Link Connector is to be used as a connector between two B+V Elevator Links with the same load capacity. It must never by used for any other purpose. Never exceed the designated load. INSTALLATION 12

13 OPERATIONS OPERATIONS 13

14 3. OPERATION WARNING: Any modification to the tool carried out without the approval of Blohm + Voss Oil Tools will void any warranty. WARNING: Using the tool with damaged or worn parts can create serious incidents. Safety The tool must only be used for the designated purpose. When using the tool, the rated load must never be exceeded Extreme Low Temperature OPERATIONS Ratings have been established at a temperature of minus 20 C. The effect of low temperature on steel must be recognized although no changes in design safety factors have been provided. When operating at low temperatures, caution must be exercised to take into account the lower impact capabilities of many steels which are typically employed. The risk of failure may be reduced by a critical load inspection. 14

15 MAINTENANCE & INSPECTION MAINTENANCE & INSPECTION 15

16 4. MAINTENANCE & INSPECTION General If cracks, excessive wear etc. is recognised, contact Blohm + Voss Oil Tools or an authorised service company. Weldings of the castings should be done only by Blohm + Voss Oil Tools or an authorised service company in according to Blohm + Voss welding procedure. A regular preventative maintenance program should be established for all Special Link Connectors. These written maintenance procedures should be given to the crew or maintenance personnel. Deterioration of equipment Dismantling The Special Link Connectors should be dismantled from the rig and inspected in a usitably equipped facility for excessive wear, cracks, flaws or deformation. Corrections should be made in accordance with recommendations which can be obtained from Blohm + Voss. Cleaning Before inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. should be removed from the areas to be inspected by a suitable method. Inspection Procedure The inspection should be made by trained, competent personnel. Normal wear in course of use will eventually reduce the capability of the Special Link Connectors. The existence or cracks, or the appearance of defects, can indicate severe deterioration, even impending failure, and prompt attention is required either to remove the elevator link from service immediately, or to undertake appropriate repair as required. Records MAINTENANCE & INSPECTION Inspection procedure are listed in this recommended practice and generalized sketches of the Special Link Connectors showing points to be inspected are to be provided. Written records should be maintained which accurately record the inspection and maintenance history of each elevator link. Records should include the date, personnel involved, and results of each inspection or maintenance procedure performed. WARNING: Never weld on Elevator Links! 16

17 3 Lubrication 1 4 The Special Link Connectors needs to be lubricated daily on the following points. Use a grease gun: 2 Grease points: 1. Pin 2. Pin 3. Pin 4. Pin Locking of screws All Screws are normally secured by a mechanical bolt lock or with a safety wire. All other screws are secured by metal adhesive (Locktite). Ensure the correct retention method is applied. Grease Quality In order to achieve efficient greasing even at different environmental temperatures, we recommend the following grease types should be used (obtainable from Blohm + Voss Oil Tools): Low-Viscosity grease Type AVIATICON Grease XRF Alternatively; Use EP1 gear lubricating grease for greasing non-oil tight gear trains when temp. < 0 C/32 F. Use EP2 when temp. > 0 C/32 F. WARNING: Ensure to wear personal safety protection like gloves and safety glasses when handling hydraulic oil and/or grease. Oil and grease may be potentially harmfull for skin and eyes. MAINTENANCE & INSPECTION Recommended grease gun 17

18 Inspection categories acc. to API RP 8B MAINTENANCE & INSPECTION Category I This category involves observing the equipment during operation for indications of inadequate performance. When in use, equipment shall be visually inspected on a daily basis for cracks, loose fits or connections, elongation of part, and other signs of wear, corrosion or overloading. Any parts found to show cracks, excessive wear, etc., shall be removed from service for further examination. The equipment shall be visually inspected by a person knowledgeable in that equipment and its function. Category II This is Category I inspection plus further inspection for corrosion, deformation, loose or missing components, deterioration, proper lubrication, visible external cracks, and adjustment. Category II may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances. Category III This is Category II inspection plus further inspection, which should include NDT of critical areas and may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances. Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paint-stripping, steam-cleaning, grit-blasting). Category IV This is Category III inspection plus further inspection for which the equipment is disassembled to the extent necessary to conduct NDT of all primary-load-carrying components. Equipment shall be: disassembled in a suitableequipped facility to the extent necessary to permit full inspection of all primary-loadcarrying components and other components that are critical to the equipment. inspected for excessive wear, cracks, flaws and deformation. Procedure: Corrections shall be made in accordance with the manufacturer s recommendations. Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paintstripping, steam-cleaning, gritblasting) Frequency Periodic inspection The recommended schedule for inspection of all kind of Elevators, Links, Special Link Connectors: Ongoing I Daily: II 6 Monthly: III 1 Year: IV Spiders: Ongoing: I Weekly: II 6 Monthly: III 1 Year: IV Power Slips: Ongoing: I Weekly: II 6 Monthly: III 2 Year: IV The recommended frequencies apply for equipment in use during the specified period. The inspection frequencies are only recommendations. The schedule of inspection heavily depends on the following factors: environment load cycles regulatory requirements operating time testing repairs re manufacture Non-periodic inspection A complete, on-job, shut-down inspection equivalent to the periodical Category III or Category IV should be made before (if anticipated) and after critical jobs (e.g., running heavy casing / drill strings, jarring, pulling on stuck pipes and/or operating at extreme low temperatures) <-20 C (<-4 F). Inspection A thorough inspection should be carried out periodically (every 3 months) or as special circumstances may require. Before starting an inspection disconnect any hydraulic/pneumatic system and remove all foreign materials (dirt, paint, grease Oil, scale, etc.) from surface by a suitable method. After a field inspection, it is advisable to record the extent of testing and testing results. Conduct the periodic or critical load inspection in the field by the crew with the supervisor. If cracks, excessive wear etc. is recognized, contact Blohm + Voss Oil Tools or an authorized service company. Inspection of Hydraulic/ Pneumatic System Check for leakage every day. Should internal or external leakage reach an unacceptable high level, contact Blohm + Voss Oil Tools or an authorized service company. 18

19 Critical Load Inspection Critical loads may occur. For example: impact loads such as jarring, pulling on stuck pipe, etc. If critical loads occurred unexpectedly, conduct the inspection immediately. Dismantling Inspection Generally, when the equipment returns to base, warehouse, etc. Carry out the Tool inspection, immediately. Furthermore, control it prior to its being sent on the next job. The Tool should be dismantled and inspected in a suitably equipped facility for excessive wear, cracks, flaws or deformations. Corrections should be made in accordance with recommendations which can be obtained from Blohm + Voss Oil Tools. Weldings at the castings should be done only by Blohm + Voss Oil Tools or an authorized service company in according to Blohm+Voss welding procedure. When need is shown in a field inspection, dismantle the Tool and arrange an inspection in a suitably equipped facility. Springs should be carefully visually inspected for excessive wear and obvious weakness. MAINTENANCE & INSPECTION 19

20 Inspection check lists CHECK LIST FRONT PAGE TYPE OF EQUIPMENT SERIAL NUMBER PART NUMBER SUPERVISOR DATE OF INSPECTION INSPECTION CATEGORY PLACE OF INSPECTION MAINTENANCE & INSPECTION 20

21 Check Category I (Ongoing observation) Observe during operation for inadequate performance. Check List Category II (Daily) CHECK FOR THE FOLLOWING GENERAL ISSUES (but not limited to): DESCRIPTION CHECKED SIGNATURE 1 Complete front page of check list for the records. OK 2 Check functioning of Link Connector as a whole. OK Remarks CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR (but not limited to): DESCRIPTION CHECKED SIGNATURE 1 Eyes. OK 2 Connection Link Plate and Link Connector Bolt OK Remarks Check List Category III (every 6 months) GENERAL DESCRIPTION CHECKED SIGNATURE 1 Carry out an Category II inspection. OK 2 NDT (MPI) critical areas. Some disassembly may be needed to do so. OK 3 Check parts for wear according to allowable tolerances. OK Remarks Check List Category IV (every year) GENERAL DESCRIPTION CHECKED SIGNATURE 1 Carry out an Category III inspection. OK 2 NDT (MPI) critical areas and load bearing components. Dismantle link to do so. OK Remarks MAINTENANCE & INSPECTION SUPERVISOR DATE 21

22 Wear data criteria Bore and Pins Elevator Link Connector PN Y Y A New Dimension: ø134,7 mm ø149,7 mm A max worn: ø135 mm ø149,2 mm B New Dimension: 136 mm ø151,3 mm B max worn: 136,3 mm ø152,4 mm C New Dimension: 150 mm 180 mm C max worn: 148 mm 178 mm A B C MAINTENANCE & INSPECTION Beyond Repair If the Special Link Connector is defective beyond repair, it should be destroyed immediately. Even if one Special Link Connector of a set is beyond repair both Special Link Connectors have to be destroyed. 22

23 Critical Areas MAINTENANCE & INSPECTION Critical areas are hatched 23

24 Handling, storage and transport Storage Storage of the tool requires the following measures to be taken: Ensure the tool is protected from water ingress Ensure the tool is stored in such a way, that personnel cannot be wounded by moving parts or sharp edges. If needed, secure the tool with ropes or otherwise in order to protect it from sliding due to ship movements. Short term storage after use and less then 3 months Preserve the tool: Grease all blank surfaces with grease: Cylinders Preserve all other blank surfaces with Tectyl Type 864 or equivalent Storage: Store in a dry environment with humidity max 80%. Commissioning: Not needed Long term storage over 3 months MAINTENANCE & INSPECTION Preserve the tool: Grease all blank surfaces with grease: Cylinders Preserve all other blank surfaces with Tectyl Type 864 or equivalent Storage: Store in a dry environment with humidity max 80% Commissioning: As per procedure in the User Manual Handling Lift the tool by its lifting eyes only. Transport When the tool is in it s original crate, use a fork lift for lifting the crate only. The weight of the tool is indicated on the identification area of the tool, and also on its original transporting crate. 24

25 DRAWINGS & SPARE PARTS 25 DRAWINGS & SPARE PARTS

26 7. DRAWINGS AND SPARE PARTS Set of B+V Type Special Link Connector PN Y, Y Parts list Item Qty. Part No. Description Special Link Connector 350 sh tons Special Link Connector 500 sh tons Elevator Link Connector DRAWINGS & SPARE PARTS

27 Parts list Item Qty. Part No. Description Connection Link Plate;350 sh tons Link Connector Bolt;350 sh tons * Securing Plate;350 sh tons * Distance Piece;for Link Connector;350 sh tons * Washer * Securing plate;350 sh tons * washer with bore * Distance Block;350 sh tons * Grease Nipple * Ring Screw * Cotter Pin * Nut Screw Screw * Dowel Pin Dowel Pin * Screw * Dowel Pin * Spare Parts Parts list Item Qty. Part No. Description Connection Link Plate;500 sh tons Link Connector Bolt * Securing Plate * Distance Piece;for Link Connector * Washer * Securing plate * Washer with bore * Distance Block * Grease Nipple * Ring Screw * Cotter Pin * Nut Screw * Screw * Dowel Pin Dowel Pin * Screw * Dowel Pin * Spare Parts DRAWINGS & SPARE PARTS 27

28 Parts list RSP Item Qty. Part No. Description * Securing Plate;350 sh tons * Distance Piece;for Link Connector;350 sh tons * Washer * Securing plate;350 sh tons * washer with bore * Distance Block;350 sh tons * Grease Nipple * Ring Screw * Cotter Pin * Nut * Screw * Dowel Pin Dowel Pin * Screw * Dowel Pin Parts list RSP Item Qty. Part No. Description * Securing Plate * Distance Piece;for Link Connector * Washer * Securing plate * Washer with bore * Distance Block * Grease Nipple * Ring Screw * Cotter Pin * Nut * Screw * Dowel Pin Dowel Pin * Screw * Dowel Pin DRAWINGS & SPARE PARTS 28

Blohm+Voss Pipe Handling Equipment Safety Clamps Type C and T Technical Documentation Original Instructions

Blohm+Voss Pipe Handling Equipment Safety Clamps Type C and T Technical Documentation Original Instructions Blohm+Voss Pipe Handling Equipment Safety Clamps Type C and T Technical Documentation Original Instructions Manual PN 88003-D Rev. 010, August 2013 Blohm + Voss is a trademark of Blohm + Voss Shipyards

More information

Blohm + Voss Pipe Handling Equipment VES-CL Center Latch Elevator, Manual Operated c/w Bushing Technical Documentation Original Instructions

Blohm + Voss Pipe Handling Equipment VES-CL Center Latch Elevator, Manual Operated c/w Bushing Technical Documentation Original Instructions Blohm + Voss Pipe Handling Equipment VES-CL 150-1000 Center Latch Elevator, Manual Operated c/w Bushing Technical Documentation Original Instructions Manual PN 611000-Y-D Rev 003 February 2012 Blohm +

More information

Blohm + Voss Pipe Handling Equipment SDS Side Door Elevators 65, 100, 150, 250, 350 & 500 tons Technical Documentation Original Instructions

Blohm + Voss Pipe Handling Equipment SDS Side Door Elevators 65, 100, 150, 250, 350 & 500 tons Technical Documentation Original Instructions Blohm + Voss Pipe Handling Equipment SDS Side Door Elevators 65, 100, 150, 250, 350 & 500 tons Technical Documentation Original Instructions Manual PN 641020-Y-BC-D Rev 013, Mai 2013 Blohm + Voss Oil Tools

More information

TECHNICAL DOCUMENTATION

TECHNICAL DOCUMENTATION Read before first use! VES-CL-1000 Elevator Hydraulically Operated Part No. 611000-Y-H Blohm + Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone ++49 (0)40/3119-1826/1162 Fax ++49 (0)40/3119-8194

More information

Blohm+Voss Pipe Handling Equipment FPS 500-AIR Flush Power Slip Technical Documentation Original Instructions

Blohm+Voss Pipe Handling Equipment FPS 500-AIR Flush Power Slip Technical Documentation Original Instructions Blohm+Voss Pipe Handling Equipment FPS 500-AIR Flush Power Slip Technical Documentation Original Instructions Manual 754000-AIR-D Rev 000, October 2012 Blohm + Voss Oiltools 1 GENERAL INFORMATION Warnings

More information

Blohm + Voss Oil Tools

Blohm + Voss Oil Tools Blohm + Voss Pipe Handling Equipment Rotary Hand Slips: RSM / RSX / LRS Drill Collar Slips: DCS / DCM / DCL Casing Slips: CSL / CSC Technical Documentation Original Instructions Manual PN 83500-D Rev 008,

More information

Blohm + Voss Pipe Handling Equipment ABVC-200 Sliptype Elevator Technical Documentation Original Instructions

Blohm + Voss Pipe Handling Equipment ABVC-200 Sliptype Elevator Technical Documentation Original Instructions Blohm + Voss Pipe Handling Equipment ABVC-200 Sliptype Elevator Technical Documentation Original Instructions Blohm + Voss Oil Tools Manual PN 672600-Y-D Rev 003, February 2012 1 GENERAL INFORMATION Warnings

More information

Blohm + Voss Pipe Handling Equipment BVE / BVS 750 Frame 1 air operated 4.1/2 14 Technical Documentation Original Instructions

Blohm + Voss Pipe Handling Equipment BVE / BVS 750 Frame 1 air operated 4.1/2 14 Technical Documentation Original Instructions Blohm + Voss Pipe Handling Equipment BVE / BVS 750 Frame 1 air operated 4.1/2 14 Technical Documentation Original Instructions Manual PN 710000-Y-A-D Rev 004, February 2012 Blohm + Voss Oil Tools 1 GENERAL

More information

Blohm + Voss Oil Tools

Blohm + Voss Oil Tools Blohm+Voss Pipe Handling Equipment Hydraulic Operated Elevator/Spider BVE / BVS 500 PN 752000-Y-H-VC 4.1/2-14 Technical Documentation Original Instructions Manual PN 752000-Y-H-VC-D Rev 001, February 2012

More information

Blohm + Voss B+V hinged Adapter

Blohm + Voss B+V hinged Adapter Blohm + Voss B+V hinged Adapter 49 /2 to 37 /2 for RT National Inspection and maintenance procedure Part No. 55320 Blohm+Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone ++49 (0)40/39-826/62

More information

Blohm + Voss Oil Tools

Blohm + Voss Oil Tools Blohm+Voss Pipe Handling Equipment VES-HCL 350 Elevator Hydraulically Operated Part no. 63000-Y-H-F (with closing signal) Technical Documentation Original Instructions Manual PN 63000-Y-H-F-D Rev 005 valid

More information

Blohm+Voss. BVE / BVS /8 7.5/8 250 metric tons

Blohm+Voss. BVE / BVS /8 7.5/8 250 metric tons Blohm+Voss BVE / BVS 250 2.3/8 7.5/8 250 metric tons Part-No. 725000 READ THESE INSTRUCTIONS BEFORE USE! Blohm+Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone ++49 (0)40/3119-1826/1162

More information

Blohm+Voss BVE/S-750 Elevator/Spider 4 ½ 14 Pipe Range Diameter

Blohm+Voss BVE/S-750 Elevator/Spider 4 ½ 14 Pipe Range Diameter Read before first use! Blohm+Voss BVE/S-750 Elevator/Spider 4 ½ 14 Pipe Range Diameter Part No. 710000-Y-H hydraulic version Blohm + Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone

More information

BVM Corporation TYPE MS TONG 6,500 FT/LBS. TORQUE

BVM Corporation TYPE MS TONG 6,500 FT/LBS. TORQUE Page 1 BVM Corporation TYPE MS TONG 6,500 FT/LBS. TORQUE Part number: Serial Number: BVM CORPORTION TYPE MS TONG 6,500 FT/LBS. TORQUE WRNING: Manual tongs which have experienced excessive wear or are found

More information

CONTROL UNIT FOR POWER SLIPS PN:

CONTROL UNIT FOR POWER SLIPS PN: CONTROL UNIT FOR POWER SLIPS PN: 757105 Blohm + Voss Oiltools Herrmann-Blohm-Strasse 2 20457 Hamburg Germany Telephone ++49 (0)40/3119-1826/1162 Fax ++49 (0)40/3119-3305 Revision 001, February 2012 All

More information

Blohm + Voss Oil Tools Circular Buttons, Inserts and Dies Catalog

Blohm + Voss Oil Tools Circular Buttons, Inserts and Dies Catalog Blohm + Voss Oil Tools Circular Buttons, Inserts and Dies Catalog A company of ThyssenKrupp Marine Systems Blohm + Voss Repair Blohm + Voss Oil Tools General Information Brochure Contents INSERTS: DIMENSIONS...

More information

350 Ton Elevator Links/Link Extensions Operation Manual

350 Ton Elevator Links/Link Extensions Operation Manual TECHNICAL MANUAL 350 Ton Elevator Links/Link Extensions Operation Manual 2005-2015 Texas International Oilfield Tools, LTD. Published by Texas International Oilfield Tools, LTD, Engineering 14620 Henry

More information

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased:

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased: Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,

More information

Pipe Handling Equipment

Pipe Handling Equipment Pipe Handling Equipment Blohm+Voss Repair GmbH Oil Tool Division Hermann-Blohm-Straße 2 20457 Hamburg, Germany Phone: +49-40-31 19-81 42 Fax: +49-40-31 19-34 00 E-mail: info@blohmvoss-oiltools.com www.blohmvoss-oiltools.com

More information

Blohm + Voss Oil Tools, LLC GraySpin Mark 40 Hydraulic Drill Pipe Spinner With and without Hydraulic Lift Technical Documentation

Blohm + Voss Oil Tools, LLC GraySpin Mark 40 Hydraulic Drill Pipe Spinner With and without Hydraulic Lift Technical Documentation Blohm + Voss Oil Tools, LLC GraySpin Mark 40 Hydraulic Drill Pipe Spinner With and without Hydraulic Lift Technical Documentation 1 GENERAL INFORMATION Warnings and Notes WARNING: A WARNING INDICATES A

More information

HST -LS Interlocking device (Translation of Original Manual)

HST -LS Interlocking device (Translation of Original Manual) Installation and Operating Manual for Components HST -LS Interlocking device (Translation of Original Manual) HST-LS Ident.-No.: 10268 HST-LS Ident.-No.: 10269 HST-LS, pictured Ident-Nr. 10269 The image

More information

CENTAX-TEST Assembly and operating instructions 053C GB3. M EN Rev. 1

CENTAX-TEST Assembly and operating instructions 053C GB3. M EN Rev. 1 Assembly and operating instructions Contents 1 General remarks... 5 2 Safety... 6 2.1 Safety remarks... 6 2.1.1 Signal words... 6 2.1.2 Pictograms... 7 2.2 Qualification of deployed personnel... 7 2.3

More information

Operating Manual TWN 0121/1. Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890

Operating Manual TWN 0121/1. Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890 TWN 0121/1 Operating Manual Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890 THIELE GmbH & Co. KG Werkstraße 3 Tel: +49 (0)2371 / 947-0 58640 Iserlohn www.thiele.de B07905-D

More information

Translation of the Original operating instructions Lifting device Z 70 /...

Translation of the Original operating instructions Lifting device Z 70 /... Translation of the Original operating instructions Lifting device Z 70 /... Content 1. Lifting device / Correct use according to regulations 2. Basic principles 3. General information 4. Special remarks

More information

Technical Description Edition 2007 Mounting, maintenance and repair of propshafts with flanged universal joints

Technical Description Edition 2007 Mounting, maintenance and repair of propshafts with flanged universal joints Technical Description Edition 2007 Mounting, maintenance and repair of propshafts with flanged universal joints 1. Recommendations Assembly, disassembly, maintenance and repair of propshafts should be

More information

MEYER-Rotating Fork Positioners are attachments used to transport loads and replace

MEYER-Rotating Fork Positioners are attachments used to transport loads and replace This MEYER-Attachment complies in every aspect to the EC-Safety Guidelines. The Certificate of Conformation / Declaration by the Manufacturer has been delivered with the attachment. The CE-Symbol can be

More information

Safety Clamp Operation Manual

Safety Clamp Operation Manual TECHNICAL MANUAL Safety Clamp Operation Manual 2005-2016 Texas International Oilfield Tools, LTD. Published by Texas International Oilfield Tools, LTD, Engineering 14620 Henry Road. Houston, TX 77060 www.texasinternational.com

More information

CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080

CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080 CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080 STI S.r.l has taken every care in collecting and verifying the documentation contained in this Instruction Manual. The information herein contained are

More information

A company of ThyssenKrupp Elevator. ThyssenKrupp Aufzugswerke. Operating Manual. Oil buffer

A company of ThyssenKrupp Elevator. ThyssenKrupp Aufzugswerke. Operating Manual. Oil buffer A company of ThyssenKrupp Elevator ThyssenKrupp Aufzugswerke Operating Manual Oil buffer OPERATING MANUAL Printer s imprint All rights reserved. Copyright by: THYSSENKRUPP AUFZUGSWERKE GMBH P.O. box 23

More information

Miller Compact Manual Quick Couplers

Miller Compact Manual Quick Couplers Miller: Issue 2 Miller Compact Manual Quick Couplers For Mini Excavators (1 to 10 tonne) and Backhoe Loaders Installation Guide and Operator s Instructions IMPORTANT Keep this manual with the machine at

More information

User Manual. T29870 Beam Clamp. Original Instructions. Rev /08//14.

User Manual. T29870 Beam Clamp. Original Instructions. Rev /08//14. User Manual T29870 Beam Clamp Original Instructions Rev 1.0-12/08//14 www.doughty-engineering.co.uk Contents Introduction... 2 Exclusion of Liability... 2 Safety Instructions... 2 Operation... 3 Maintenance...

More information

Safelift Overhead Runway Beams & Rolling Beam Cranes

Safelift Overhead Runway Beams & Rolling Beam Cranes Operation & Maintenance Instructions Instructions for Safe Use Safelift Overhead Runway Beams & Rolling Beam Cranes Certification Safelift overhead runway beams and rolling beam cranes are lifting appliances

More information

500kg TELESCOPIC TRANSMISSION LIFTER

500kg TELESCOPIC TRANSMISSION LIFTER Product Code: 2056T PRODUCT CODE: 2056T 500kg TELESCOPIC TRANSMISSION LIFTER Safe Working Capacity 500kg Base Dimension 540 x 570 mm Minimum Height 1175mm Maximum Height 1900mm Made in China to TQB Brands

More information

CENTAFLEX-K Assembly and operating instructions 014K S... M EN Rev. 1

CENTAFLEX-K Assembly and operating instructions 014K S... M EN Rev. 1 Assembly and operating instructions Contents 1 General remarks... 5 2 Safety... 6 2.1 Qualification of deployed personnel... 6 2.2 Warning notes... 6 2.2.1 Signal words... 6 2.2.2 Symbols... 7 2.3 Application

More information

Lineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2

Lineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2 Lineman s Hoist LMST0- Operating, Maintenance & Parts Manual Lineman s Hoist Follow all instructions and warnings for inspecting, maintaining and operating this hoist. The use of any hoist presents some

More information

500kg HYDRAULIC TABLE LIFT

500kg HYDRAULIC TABLE LIFT Product Code: 6007T OWNER S MANUAL PRODUCT CODE: 6007T 500kg HYDRAULIC TABLE LIFT Working Load Limit 500kg Maximum Height 1575mm Minimum Height 440mm Table Dimensions 1010x520mm Wheel Diameter 150mm Made

More information

SPARKSCAN1 HIGH VOLTAGE CLAMP OPERATING MANUAL

SPARKSCAN1 HIGH VOLTAGE CLAMP OPERATING MANUAL SPARKSCAN1 HIGH VOLTAGE CLAMP OPERATING MANUAL MOTORTECH Tools & Test Equipment for Ignition Systems P/N 01.10.019 Rev. 01/2013 Copyright Copyright 2012 MOTORTECH GmbH. All rights reserved. Distribution

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Globe control valve, pneumatically operated Actuator sizes 40 mm - 125 mm, Nominal diameter DN10-65 Kolbengesteuertes Geradsitzventil Antriebsgrößen 40 mm - 125 mm, Nennweiten DN10-65 Vanne à siège droit

More information

STRUT SPRING COMPRESSOR

STRUT SPRING COMPRESSOR OWNER S MANUAL PRODUCT CODE: 1221T STRUT SPRING COMPRESSOR Capacity Stroke Spring Coil Spring Spring Coil Net Weight (Maximum) Thickness Length Diameter 1,000kg 330mm 10-18mm 210-570mm 100-158mm 36kg Made

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Industrial Process Installation, Operation, and Maintenance Manual Series PBV Plastic Lined Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health

More information

CENTAX-SEC Series B Assembly and operating instructions CX BFS1-LE/SE-**-B M EN Rev. 1

CENTAX-SEC Series B Assembly and operating instructions CX BFS1-LE/SE-**-B M EN Rev. 1 Assembly and operating instructions -**-B Contents 1 General remarks... 5 2 Safety... 6 2.1 Safety remarks... 6 2.1.1 Signal words... 6 2.1.2 Pictograms... 7 2.2 Qualification of deployed personnel...

More information

Operating manual. Custom made gearboxes

Operating manual. Custom made gearboxes Operating manual Custom made gearboxes DSS-Nr. 100389549 DSS-Rev. 001 Datum 16.01.2018 Contents Contents 1 General information 3 1.1 Using the operating manual 3 1.2 Warnings in this operating manual 4

More information

Keystone Butterfly valves ParaSeal Installation and maintenance instructions

Keystone Butterfly valves ParaSeal Installation and maintenance instructions Before installation these instructions must be fully read and understood Please read these instructions carefully Hazard potentials: disregarding of instructions improper use of product insufficiently

More information

Turbocharger / A100-L Original assembly instructions English

Turbocharger / A100-L Original assembly instructions English Assembly Instructions Turbocharger / A100-L Original assembly instructions English This document is valid for the A100-L series: A165-L, A170-L, A175-L, A180-L, A185-L, A190-L Purpose The assembly instructions

More information

OPERATING MANUAL C-1350 CABLE PUSHER. Copyright 2003 by CBS Products (KT), Ltd

OPERATING MANUAL C-1350 CABLE PUSHER. Copyright 2003 by CBS Products (KT), Ltd CBS Products (KT), Ltd, Pillings Road, Oakham, Rutland, LE15 6QF. UK Telephone: +44(0)1572723665 Fax: +44(0)1572 756006 E-Mail: sales@cbsproducts.com Website:www.cbsproducts.com OPERATING MANUAL C-1350

More information

Turbocharger / VTR..0, VTR..1 Original assembly instructions English

Turbocharger / VTR..0, VTR..1 Original assembly instructions English Assembly Instructions Turbocharger / VTR..0, VTR..1 Original assembly instructions English This document is valid for the VTR..0/..1 series: VTR160, VTR200, VTR250, VTR320, VTR400 VTR161, VTR201, VTR251,

More information

Instruction Manual. Unique 7000 Series Aseptic - Manually Operated ESE02421-ENUS Original manual

Instruction Manual. Unique 7000 Series Aseptic - Manually Operated ESE02421-ENUS Original manual Instruction Manual Unique 7000 Series Aseptic - Manually Operated 2210-0042 ESE02421-ENUS1 2013-03 Original manual Table of contents The information herein is correct at the time of issue but may be subject

More information

RENFROE. WARNING: Before putting tool in service, take to your immediate supervisor.

RENFROE. WARNING: Before putting tool in service, take to your immediate supervisor. WARNING: Before putting tool in service, take to your immediate supervisor. RENFROE Model NM Clamp Application, Operation and Maintenance Manual OM 211-NM Operators Manual This Operator s Manual covers

More information

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference!

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference! Tension Meter FT Series S C H M I D T c o n t r o l i n s t r u m e n t s Edition FT 03.E Model FT Instruction Manual Valid as of: 01.09.2011 Please keep the manual for future reference! Contents 1 Warranty

More information

Declaration of Conformity as per Directive 97/23/EC

Declaration of Conformity as per Directive 97/23/EC Declaration of Conformity as per Directive 97/23/EC The manufacturer declares that:, 47906 Kempen, Germany PTFE-lined Rotary plug valves Series 23e, with packing with lever for 90 operation with worm gear

More information

HEAVY DUTY WHEEL LIFTER

HEAVY DUTY WHEEL LIFTER OWNER S MANUAL PRODUCT CODE: BTWD750 HEAVY DUTY WHEEL LIFTER Capacity Lift Arm Lifting Tilt Range Dimensions Net (Max) Spread Range (degrees) (L x W x H) Weight 750kg 533-635mm 60-275mm -2.5-10mm 787x1092x895mm

More information

Condensate Drain Valve AK 45. Original Installation Instructions English

Condensate Drain Valve AK 45. Original Installation Instructions English Condensate Drain Valve AK 45 EN English Original Installation Instructions 810467-03 1 Contents Important Notes Page Usage for the intended purpose...4 Safety note...4 Danger...4 Attention...4 PED (Pressure

More information

Pneumatic Cylinder 14 Bore X 21 Stroke Part No. P Replaces Part No. P

Pneumatic Cylinder 14 Bore X 21 Stroke Part No. P Replaces Part No. P Pneumatic Cylinder 14 Bore X 21 Stroke Part No. P -322908-00000 Replaces Part No. P-191067-00000 Service Information WARNING: INSTALLATION AND MOUNTING The user of these devices must conform to all applicable

More information

OPERATION & SERVICE MANUAL DRUM (MANUAL DRUM LIFTER)

OPERATION & SERVICE MANUAL DRUM (MANUAL DRUM LIFTER) OPERATION & SERVICE MANUAL DRUM-55-36 (MANUAL DRUM LIFTER) Vestil Manufacturing Corp. 2999 North Wayne St., Angola, IN 46703 Ph: 260-665-7586. Fax: 260-665-1339 E-mail: Sales@vestil.com Website: www.vestil.com

More information

TRUSS KITS FOR SPOUTING Installation Manual

TRUSS KITS FOR SPOUTING Installation Manual TRUSS KITS FOR SPOUTING Installation Manual LAMBTON CONVEYOR LIMITED 102 Arnold Street Wallaceburg, ON N8A 3P4 Canada Telephone: (519) 695-2316 Telephone: (519) 627-8228 ONE SOURCE ONE SOLUTION Toll free:

More information

Model 6 Weld-On Drawbar Eye

Model 6 Weld-On Drawbar Eye MANUFACTURING CO. THE FIRST NAME IN QUALITY COUPLINGS Installation, Inspection, Operation & Maintenance Guide Model 6 Weld-On Drawbar Eye IMPORTANT Read these instructions completely before installing,

More information

Innovative Landing String system for ultra-deep offshore

Innovative Landing String system for ultra-deep offshore Innovative Landing String system for ultra-deep offshore V. Flores, J.Franchi, S. Granger Vallourec Drilling Products A. Vierke, J. Grotherr Blohm+Voss Oil Tools Introduction Offshore industry trends:

More information

Operating Manual for extrusion valve MMKD-40 KV/LV/LVP

Operating Manual for extrusion valve MMKD-40 KV/LV/LVP Operating Manual for extrusion valve MMKD-40 KV/LV/LVP Read this manual carefully before installing, operating or servicing this equipment. Keep always handy for further use. ALFRED SCHÜTZE Apparatebau

More information

INSTRUCTION MANUAL. Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps

INSTRUCTION MANUAL. Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps INSTRUCTION MANUAL Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps IMPORTANT Please read this instruction manual before using these products. This manual contains

More information

RENFROE. WARNING: Before putting tool in service, take to your immediate supervisor. Model SCSL Clamp Application, Operation and Maintenance Manual

RENFROE. WARNING: Before putting tool in service, take to your immediate supervisor. Model SCSL Clamp Application, Operation and Maintenance Manual WARNING: Before putting tool in service, take to your immediate supervisor. RENFROE Model SCSL Clamp Application, Operation and Maintenance Manual OM 311 SCSL Operators Manual This Operator s Manual covers

More information

USE AND MAINTENANCE MANUAL

USE AND MAINTENANCE MANUAL LATERAL TURNOVER 360 ORIGINAL INSTRUCTIONS INTRODUCTION This manual includes instructions for assembly, maintenance (regular and extraordinary), and for possible faults with remedies. The instructions

More information

CENTAFLEX-H Assembly and operating instructions 008H /3000 M EN Rev

CENTAFLEX-H Assembly and operating instructions 008H /3000 M EN Rev 008H-00400-1000/3000-1000 -3000-1000 -3000 Contents 1 General remarks... 5 2 Safety... 6 2.1 Safety remarks... 6 2.1.1 Signal words... 6 2.1.2 Pictograms... 7 2.2 Qualification of deployed personnel...

More information

-ty EYDESCREEN MANUF=ACTUFIINC. Operating lnstructions MANUAL

-ty EYDESCREEN MANUF=ACTUFIINC. Operating lnstructions MANUAL -ty EYDESCREEN MANUF=ACTUFIINC Operating lnstructions MANUAL Operating Instructions MANUAL All rights reserved, in particular the right to duplicate and distribute and to translate the present document.

More information

MG12K24T60V4 Mechanical Grapple

MG12K24T60V4 Mechanical Grapple 170 State Route 271 Attachment Solutions MG12K24T60V4 Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information....

More information

Instruction Manual. LKAP Air-Operated Valve ESE01993-EN Original manual

Instruction Manual. LKAP Air-Operated Valve ESE01993-EN Original manual Instruction Manual LKAP Air-Operated Valve ESE01993-EN6 2016-07 Original manual Table of contents The information herein is correct at the time of issue but may be subject to change without prior notice

More information

Turbocharger / TPS-H Original assembly instructions English

Turbocharger / TPS-H Original assembly instructions English Assembly Instructions Turbocharger / TPS-H Original assembly instructions English This document is valid for the TPS-H series: TPS44-H, TPS48-H, TPS52-H Purpose TPS-H turbocharger The assembly instructions

More information

Pneumatic Cylinder 14 Bore X 22 Stroke Part No. R (Formerly P )

Pneumatic Cylinder 14 Bore X 22 Stroke Part No. R (Formerly P ) Pneumatic Cylinder 14 Bore X 22 Stroke Part No. R434001268 (Formerly P -193419-00003) Service Information INSTALLATION Before installing this cylinder, all air lines in the system should be blown clean

More information

Installation and Operation Manual

Installation and Operation Manual 1645 Lemonwood Dr. Santa Paula, CA 93060 USA Toll Free: 1 (800) 253-2363 Tel: 1 (805) 933-9970 rangerproducts.com Ranger Floor Jack Installation and Operation Manual Manual Revision B July 2017 Manual

More information

In This Document MODULE DESCRIPTION This module provides information on the safety concerns and

In This Document MODULE DESCRIPTION This module provides information on the safety concerns and Crane Safety Fact Sheet In This Document MODULE DESCRIPTION This module provides information on the safety concerns and Introduction necessary precautions you will need to be aware of when working Crane

More information

Side Door Elevator SDS

Side Door Elevator SDS Pipe-Handling-Equipment Hoisting Equipment Side Door Elevator SDS SDS / VES SDS / SDS-H Type Series Manual and hydraulic operated elevators SDS Type Series Side Door Collar Type Elevator VES SDS Type Series

More information

PORTABLE LADDER SAFETY PROGRAM

PORTABLE LADDER SAFETY PROGRAM PORTABLE LADDER SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.25 Portable Wood Ladders* - 29 CFR 1910.26 Portable Metal Ladders* - 29 CFR 1926.1050-1060* *The above standards are intended to prescribe

More information

OWNER S MANUAL PRODUCT CODE: 2006T

OWNER S MANUAL PRODUCT CODE: 2006T Jul-18 Product Code: 2006T OWNER S MANUAL PRODUCT CODE: 2006T HYDRAULIC PIPE BENDER 12,000KG Model Capacity Bending Die No of Attachments 12,000kg 1/2", 3/4", 1", 1-1/4", 1-1/2", 2" 6 Made in China to

More information

Operating Instructions Hoist Chains EN 818-7

Operating Instructions Hoist Chains EN 818-7 Operating Instructions Hoist Chains EN 818-7 THIELE GmbH & Co. KG Werkstraße 3 Phone: +49 (0) 2371 / 947-0 58640 Iserlohn www.thiele.de B08285-B Page 1 EN-170114 Table of Contents 1 Introduction... 2 2

More information

Broetje-Automation Company Standard Coating

Broetje-Automation Company Standard Coating Broetje-Automation Company Standard Table of Contents Scope and Objective... 2 1 Standards and Corrosion Protection... 2 1.1 Standards... 2 1.2 Corrosion Resistance... 2 2 Surface Preparation... 3 2.1

More information

BODAS Pressure sensor PR3 series 10

BODAS Pressure sensor PR3 series 10 BODAS Pressure sensor PR3 series 10 RE 95155 Edition: 04.2014 Replaces: 12.2013 Measurement ranges to 25, 50, 160, 200, 250, 400, 600 bar Ratiometric output signal 0.5 to 4.5 V with 5 V supply voltage

More information

Bulletin E460. Compact Valves. with high flow capacity. ROSS Air Control Products

Bulletin E460. Compact Valves. with high flow capacity. ROSS Air Control Products Bulletin E60 Compact Valves with high flow capacity ROSS Air Control Products ROSS Compact Valves small in size, but ready for big challenges... The new line of ROSS compact valves consists of /-, /- and

More information

Distributed by Tri-State Equipment Company Inc. Web: PH: FAX:

Distributed by Tri-State Equipment Company Inc.   Web:   PH: FAX: Lineman s Hoist Distributed by Tri-State Equipment Company Inc. Email: sales@tsoverheadcrane.com Web: www.tsoverheadcrane.com PH: -869-00 FAX: -869-6 LMST680 Operating, Maintenance & Parts Manual Lineman

More information

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Version with handwheel Mounting and Operating Instructions EB 8039 EN Edition May 2016 Definition of signal

More information

Installation and Operational Instructions for ROBA -D Couplings Type 91_. _

Installation and Operational Instructions for ROBA -D Couplings Type 91_. _ Please read the Installation and Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to coupling failure, resulting in damage to other

More information

Model 407SE Swivel Drawbar Eye

Model 407SE Swivel Drawbar Eye MANUFACTURING CO. THE FIRST NAME IN QUALITY COUPLINGS Installation, Inspection, Operation & Maintenance Guide Model 407SE Swivel Drawbar Eye IMPORTANT Read these instructions completely before installing,

More information

DC Master 24/ A

DC Master 24/ A USERS MANUAL DC Master 24/12 50-60A DC-DC converter MASTERVOLT Snijdersbergweg 93, 1105 AN Amsterdam The Netherlands Tel.: +31-20-3422100 Fax.: +31-20-6971006 www.mastervolt.com ENGLISH Copyright 2015

More information

CE Operating and Maintenance Manual

CE Operating and Maintenance Manual CE Operating and Maintenance Manual Demolition and Sorting Grab Type S 450-D Zijtveld Grijpers The Netherlands www.zijtveld-grijpers.nl 1 Introduction Dear User, The Demolition/Selector grab is a piece

More information

ov-lifting_bolts_divider - Updated Lifting Bolts

ov-lifting_bolts_divider - Updated Lifting Bolts ov-lifting_bolts_divider - Updated - 09-01-2017 Lifting Bolts Technical Information roduct information Lifting Bolts roduct marking Compliant with 2006/42/EC, and with individual date of manufacture and

More information

Installation Instructions. Install Hubs Set Spacing Install Element FINISHED BORE INTERFERENCE FIT. Step 1 - HUB INSTALLATION

Installation Instructions. Install Hubs Set Spacing Install Element FINISHED BORE INTERFERENCE FIT. Step 1 - HUB INSTALLATION Instruction Manual for Baldor Dodge Raptor Spacer Couplings These instructions must be read thoroughly before installing or operating this product. Video walkthroughs of each installation procedure are

More information

INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700

INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700 INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700 11.106.32.0001 INOXPA, S.A. c/telers, 54 Aptdo. 174 E-17820 Banyoles Girona (Spain) Tel. : (34) 972-57 52 00 Fax. : (34) 972-57 55 02 email:

More information

INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700

INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700 INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS Y-FILTER 83700 11.106.32.0001 INOXPA, S.A. c/telers, 54 Aptdo. 174 E-17820 Banyoles Girona (Spain) Tel. : (34) 972-57 52 00 Fax. : (34) 972-57 55 02 email:

More information

Type 6213 EV, 6281 EV

Type 6213 EV, 6281 EV Type 6213 EV, 6281 EV 2/2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions

More information

Oil-free piston compressors KK and piston vacuum pumps KV

Oil-free piston compressors KK and piston vacuum pumps KV Oil-free piston compressors KK and piston vacuum pumps KV Installation and Operating Instructions 0678106030L02 1707V003 Contents Important information 1 About this document 2 1.1 Warnings and symbols

More information

AC 100. Operating instructions Pneumatic Crimper AC 100. Date of issue: 05/2010. Keep for future use!

AC 100. Operating instructions Pneumatic Crimper AC 100. Date of issue: 05/2010. Keep for future use! Operating instructions Pneumatic Crimper AC 100 Date of issue: 05/2010 Keep for future use! SAFETY SAFETY Basic information The basic prerequisite for ensuring safe use and continuous operation of the

More information

Installation manual wall-mounted distributor

Installation manual wall-mounted distributor EN Installation manual wall-mounted distributor EN 60003233 Issue 11.2016 2016-14-11 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2

More information

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves Type 3347-1 and Type 3347-7 Pneumatic Control Valves Type 3347-7, cast body with welding ends Type 3347-7, bar stock body with threaded connections Mounting and Operating Instructions EB 8097 EN Edition

More information

KEYSTONE SERIES 320 BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS

KEYSTONE SERIES 320 BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS Before installation these instructions must be fully read and understood HAZARD POTENTIALS disregarding of instructions improper use of product insufficiently qualified personnel Valve application to be

More information

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK CONTENTS: Page 1 Specifications 2 Warning Information 3 Setup Instructions 4 Operating Instructions, Preventative Maintenance, Inspection and Proper Storage 5 Hydraulic Jack Maintenance Guide and Regular

More information

Installation and operating manual

Installation and operating manual LK product no: 901002 and 901102 501002 and 501102 (JIS) Article no: 74500 Revision: 9 Article no: 74500 Revision: 9 2 (23) Contents 1. General information... 5 2. Safety precautions... 5 2.1 Significance

More information

Assembly instructions PRORUNNER mk1 2

Assembly instructions PRORUNNER mk1 2 Assembly instructions PRORUNNER mk1 Version 0.1 / 01-JUN-2013 Copyright Qimarox B.V. All rights reserved. No part of this document may be copied, stored in a database and/or published by means of printing,

More information

6722 Rev. A CAPACITY: 22 TON TRUCK AXLE JACK WITH AIR RETURN

6722 Rev. A CAPACITY: 22 TON TRUCK AXLE JACK WITH AIR RETURN CONTENTS: Page Specifications 2 Warning Information Setup Instructions and Operating Instructions 4 Preventative Maintenance, Inspection and Proper Storage 5 Troubleshooting, Owner/User Responsibility

More information

SuperGrip SG. User s manual

SuperGrip SG. User s manual SuperGrip SG User s manual This publication contains instructions for the installation and handling of the SuperGrip SG grapples. The instructions cover both general information for all models, and procedures

More information

Operating & Maintenance Manual For Steam Conditioning Valve

Operating & Maintenance Manual For Steam Conditioning Valve For Steam Conditioning Valve 1 Table of Contents 1.0 Introduction 3 2.0 Product description 3 3.0 Safety Instruction 4 4.0 Installation and Commissioning 5 5.0 Valve Disassembly 6 6.0 Maintenance 6 7.0

More information

PAGE 1 OF 5 HEALTH, SAFETY & ENVIRONMENTAL MANUAL PROCEDURE: S360 Overhead Cranes & Lifts Procedure REV 4.0 8/14/2012

PAGE 1 OF 5 HEALTH, SAFETY & ENVIRONMENTAL MANUAL PROCEDURE: S360 Overhead Cranes & Lifts Procedure REV 4.0 8/14/2012 PAGE 1 OF 5 PURPOSE: OVERHEAD CRANES AND LIFTS PROCEDURE The purpose of this procedure is to define the safety and training requirements for use of overhead cranes and lifts. Procedure: Definitions Designated

More information

Safe Operating Practices & Maintenance Manual

Safe Operating Practices & Maintenance Manual tcamerican.com sales@tcamerican.com 763-479-7000 11110 Industrial Circle NW, Suite A, Elk River, MN 55330 Safe Operating Practices & Maintenance Manual Section Subject Page A. General 2 B. Operator Qualifications

More information