Replace front brake pads and discs * (Ford Galaxy )
|
|
- Elijah Grant
- 5 years ago
- Views:
Transcription
1 Replace front brake pads and discs * (Ford Galaxy ) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're not sure - don't act! Administration will not accept any responsibility for damage to you or your vehicle after following these instructions bellow. Tools we need: Jack + stand(s), ratchet with set of sockets, 7mm allen bit (key), piece of wire or cord anything to hang caliper to suspension spring, hammer, breaker bar, metal brush, caliper rewind tool (See Image 1 below, make sure it's big enough to fit Ford Galaxy'S-Max brake piston), pry bar or flat head screwdriver, brake line clamp and 9mm spanner and hose for the nipple (all these 3 are optional), copper or silicone grease, nice to have a torque wrench. Posted by: waway This is how we do it: Change pads and discs. 1. Removing brake pads: - Page 1 of 12 -
2 - jack up the car (front or the side where you doing brakes), don't use jack on it's own - much safer to have a stand (Image 2) and remove the wheel *NOTE: It's easier to remove wheel if you loosen wheel nuts while the car is on the ground - using pliers or screwdriver remove caliper spring (Image 3) - remove covers for caliper pin bolts and remove pin bolts (Image 4) using 7mm allen bit (once they loose you can pull them with thin pliers or push them out with a screwdriver) - using pry bar or screwdriver wiggle caliper out, DO NOT (!) hang it on a brake line, but attach it to suspension spring with a piece of wire or string (Image 5) *NOTE: From this moment while caliper is loose DO NOT press brake pedal, otherwise piston may come out too far - remove brake pads, one from caliper piston - pull out, another from caliper bracket 2. Removing brake disc: - remove caliper bracket held by 2x18mm bolts (Image 6) Some cars may have a little bolt at the front of the disc to hold it in place when wheel is of, or little clips around wheel studs. If you don't have either of that, brake disc still can be held by rust, so it might need a good knock by a hammer to help it to come off. - Page 2 of 12 -
3 - when disc is off clean surface underneath with a metal brush and apply some copper grease to prevent sticking in the future 3. Installing new disc: - simply put it on (if there was no bolt or clips) - brake disc is held in place by wheel nuts together with the wheel - attach caliper bracket back and tighten those 18mm bolts up to 90Nm + 90 degrees (that's tight), if you are re-using bolts you might not be able to do extra 90 degrees just make sure they are tight - use brake and clutch cleaner spray to make sure there is no grease on you disc (some brake discs come in sealed bags covered in oil to prevent them from rusting during storage). 4. Installing new brake pads: - push caliper piston back as far as it goes using caliper re-wind tool (Image 1) Brake fluid will be forced to go back, and there are 2 ways you can direct it: a. Just let it go back to the system, in this case keep observing brake fluid level in expansion tank (Don't let any of brake fluid on a paintwork because it can damage it) b. Jam brake line with hose clamp (like the one on Image 7 or any other type), put tube/hose on the caliper nipple (Image 8) and drain brake fluid from caliper piston to jar or bottle Whichever way you choose - keep brake fluid level under control - Page 3 of 12 -
4 - instal new brake pads, one goes into bracket another clips in into caliper piston - apply some copper grease on a back of the pads where it contacts caliper. Make sure there is no grease on braking surfaces! - put caliper back into place. Make sure that brake line is not twisted! - clean and lubricate pins/bolts and tighten them up to 25Nm - install caliper spring Now do the same for the other wheel. Important! Before you go press brake pedal few times to get brake fluid into the pistons. Also for first time while driving allow good distance for braking, because pads and discs need to rub to each other. Here's YouTube video: - Page 4 of 12 -
5 Image 1 - Brake caliper rewind tool - Page 5 of 12 -
6 Image 2 - Jacked up car - Page 6 of 12 -
7 Image 3 - Caliper spring - Page 7 of 12 -
8 Image 4 - Caliper pin bolts - Page 8 of 12 -
9 Image 5 - Brake caliper attached to suspension spring - Page 9 of 12 -
10 Image 6 - Caliper bracket held by 2x18mm bolts - Page 10 of 12 -
11 Image 7 - Hose clamp - Page 11 of 12 -
12 Image 8 - Caliper nipple - Page 12 of 12 -
Replace brake pads and discs - front * (Volkswagen Sharan 2010-Present)
Replace brake pads and discs - front * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions,
More informationReplace brake pads and discs - rear * (Volkswagen Golf )
Replace brake pads and discs - rear * (Volkswagen Golf 1997-2004) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and
More informationReplace clutch and flywheel * (Volkswagen Sharan 2010-Present)
Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if
More informationPowerslot Mustang Rotors (Rear Pair GT/V6) - Installation Instructions
Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) - Installation Instructions The below installation instructions work for the following products: Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) Please
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationThe following information shows the steps to change the rear brake pads and rotors on an E36 chassis.
1 of 20 1/18/2010 9:15 PM See More DIY Articles Bookmark Site! The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. Disclaimer: The following information
More informationMirrored from:
Mirrored from: http://www.wranglerforum.com/f274/install-synergy-suspension-ball-joints-write-up-147062.html 03-18-2012, 02:43 AM #1 SilverSport Supporting Member WF Supporting Member Install Synergy Suspension
More informationSteeda Bumpsteer Kit (94-04) - Installation Instructions
Steeda Bumpsteer Kit (94-04) - Installation Instructions The below installation instructions work for the following products: Steeda Bumpsteer Kit (94-04) Please read through the instructions carefully
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationCommander SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 - FRONT UPPER A-ARMS 2 - FRONT LOWER A-ARMS 4 - COTTER PINS 2-12MM JAM NUTS 2 - TIE ROD EXTENDERS 8- FLANGED DELRON BUSHINGS 4- DELRON CASTER SPACERS 6 - GREASE FITTINGS 3 - BEARING REMOVAL
More informationPerformance Brake Caliper Guide Bushing Set Installation Guide
Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationRear Parking Brake Cable (93 Cobra)
Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and
More informationHawk HP Performance Brake Pads (94-98 GT/V6 Front Pair) - Installation Instructions
Hawk HP Performance Brake Pads (94-98 GT/V6 Front Pair) - Installation Instructions The below installation instructions work for the following products: Hawk HP Plus Performance Brake Pads (94-98 GT/V6
More informationFord Focus Front Brake Pad Replacement
2005-2007 Ford Focus Front Brake Pad Replacement Replacing the brake pads on all 2005-2007 Focus models with rear drum brakes. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationAudi B5 A4/S4 Rear Wheel Bearing Service Kit
Audi B5 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More information2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up.
FRONT BRAKES: 2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up. 1. Remove this bolt holding brake line bracket to the suspension. 2. I had to replace all 4 rotors at 60K miles, so
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationAudi B6/B7 A4/S4 Rear Wheel Bearing Service Kit
Audi B6/B7 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationDodge Caravan Brake Pads and Rotors Replacement
2001-2007 Dodge Caravan Brake Pads and Rotors Replacement Written By: aelegg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide shows how easy it is for someone with little skills to
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationAudi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions
Audi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal
More informationFord Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions
Ford Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions Time Necessary: Approximately 1.5 hours Tools Required: 15 MM Socket Ratchet PryBar Floor Lift or: o Floor Jack o (2) Jack Stands
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS POWER FRONT DISC CONVERSION KIT A126-7 1963-66 CHEVY C10 PICKUP NON-POWER FRONT DISC CONVERSION KIT A126-8 1963-72 CHEVY C10 PICKUP Thank you for choosing STAINLESS STEEL BRAKES
More informationTriumph Brake Kit TR4A/TR250/TR6 PART # Rutherford St. P.O. Box 847 Goleta, CA FAX
1. Lift the front of the car with a jack and place it on jackstands. Take off the front wheels. 2. Use two 9/16 combination wrenches to disconnect the soft brake line from the body and hard line connection
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More informationSCION tc BIG BRAKE KIT Section I - Installation Preparation
SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper
More informationRelease the electrical wire from the bracket -2- toward the left -A- and remove.
Page 1 of 8 Front Brake Pads, FBC-60, Removing and Installing Always replace on both axles. Special tools and workshop equipment required t Torque Wrench 5 50 Nm -V.A.G 1331- t Reversible Ratchet -V.A.G.
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More informationNEW BRAKE INSTALLATION. Let us show you how a
Tech Article From Newsletter 17.2-2nd Quarter of 2011 NEW BRAKE INSTALLATION Let us show you how a Big Brake Install is easier than you think!! So, you have a 572 (or a hot 383) in your shoebox... you
More informationNote: ToyTec recommends that all products are installed by trained professionals.
ToyTec Front Suspension Install Instructions 2.5" Front Suspension Kit 2003 2009 Toyota 4Runner, 2007 2009 Toyota FJ Cruiser, 2005+ Toyota Tacoma, 2002-2009 Prado 120, 2005-2011 Toyota Hilux Note: ToyTec
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationBMW 3 Series E46 Front Wheel Bearing
BMW 3 Series E46 Front Wheel Bearing Replacement A step-by-step guide on BMW 3 Series E46 Front Wheel Bearing Replacement. Written By: Danielle 2017 guides.drivediy.com Page 1 of 13 INTRODUCTION Discover
More informationBHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
More informationv Porsche 928
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
More informationInstallation instructions, accessories - Fuel driven heater 912-D
XC90 Section Group Weight(Kg/Pounds) Year Month 8 87 2002 10 XC90 2003 D5244T, XC90 2004 D5244T, XC90 2005 D5244T AW50/51 AWD, XC90 2006 D5244T, XC90 2006 D5244T AW50/51 AWD D5244T R8703687 Page 1 of 20
More informationNext, set the bar level and tighten it down. Do this on both the driver and passenger sides.
Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Using two tape measures, measure the outside width at the front and the rear of the tubes. The front dimension
More informationFORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1)
FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationThis guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationLMB-C6 CF Senior Member
LMB-C6 CF Senior Member Rotor install DIY... ****** FRONT: ****** Remove the wheel. To remove the rotor you need to remove the caliper and the bracket. There are 2 bolts for the caliper (top smaller bolt
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More informationHow To: Replace Brembo front discs & pads
How To: Replace Brembo front discs & pads Necessary Tools required Good quality socket set. T55 Torx/spline bit of very good quality. T30 Torx/spline bit. T27 Torx /spline bit WD40 Mallet. Punch. Brake
More informationTeam Z Motorsports. K-Member installation instructions
Team Z Motorsports K-Member installation instructions Parts Included: 1-Tubular K-Member Needed Items-Solid Steering Shaft Offset Steering Rack Bushings Optional-Heavy Duty Bolt Kit Tubular Front Lower
More informationALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1)
ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack Stands
More information1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.
Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationFirst, check and record the camber and caster readings, they will be adjusted later.
First, check and record the camber and caster readings, they will be adjusted later. The caliper-mounting bosses are machined perpendicular to the spindle so they are an excellent place for the level.
More informationThis Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs
1 2 3 This Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs Thank you for purchasing the CorkSport Mazda
More informationInstallation Instructions for disc brakes
Installation Instructions for disc brakes Bedford CF 230-280, built 1974-1986, not suitable for vehicles with rear twin tyres Included 2 pcs. Wheel Hubs with Wheel Bolts, Mounted Brake Discs and Wheel
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationNext, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.
Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore
More informationOMIX-ADA EXHAUST MANIFOLD
OMIX-ADA EXHAUST MANIFOLD Installation Time: 240 Minutes Tools Required: 3/8 ratchet 3/8 3 extension 10 mm socket 13mm socket 9/16 socket Flashlight 9/16 box end wrench Pocket screw driver Can of brake
More informationPypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & GT) - Installation Instructions
Pypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & 94-97 GT) - Installation Instructions The below installation instructions work for the following products: Pypes 409 Stainless
More informationDetroit Tuned R56 Oil Service How-To
Detroit Tuned R56 Oil Service How-To Welcome to Detroit Tuned s how-to guide for an oil service for an R56 MINI Cooper. It s always best to do an oil change on a hot engine as the hot oil will drain better
More informationSuzuki GS1000G fork seal replacement
Suzuki GS1000G fork seal replacement Before you start you require: 1) To read workshop service manual for your model 2) Socket allen key M8 3) Torque wrench 4) Special tool to hold inner, make your own,
More information55-64 Full Size Chevy
55-64 Full Size Chevy Installation Instructions Power Disc Conversion 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand tools. The only tools you may not
More informationSUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version
SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm Introduction Acrobat Printable Version I'd like to thank Ben Davis for providing the pictures for this procedure. Ben took the time to take
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More informationService Procedure. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels.
Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on
More informationOVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf. This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same.
OVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same. Badly corroded calipers (caused by moisture in the
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 68-74 X Body 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand
More informationRemoving/installing final drive
1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm
More information1 of 11 4/11/ :35 AM
1 of 11 4/11/2015 11:35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM-6007-30 Adaptor Removal Procedure 2 of 11 4/11/2015 11:35 AM Caution: Refer to Brake Dust Caution
More informationMK5/MK6 Panzer Plate Install Instructions
MK5/MK6 Panzer Plate Install Instructions This is the install procedure for the dieselgeek.com MK5/MK6 Panzer Plate Skid Plate Kits. These instructions are for the following vehicles, regardless of engine
More informationReplacement Front Outer Tie Rod End (85-93 All)
Replacement Front Outer Tie Rod End (85-93 All) Materials in the box: One outer tie rod end, castle nut, cotter pin, nut, and grease fitting. Tools Needed: Jack and Jack Stands Pry bar (you may or may
More information86-95 Suzuki Samurai Complete Contact Spring Over Axle Pads (SKU# SSP-CCSP4) Installation Instructions
86-95 Suzuki Samurai Complete Contact Spring Over Axle Pads (SKU# SSP-CCSP4) Installation Instructions Revised 4/17/18 Front Pads (SSP-CCFP) Rear Pads (SSP-CCRP) Suggested Tools: CAUTION: Safety glasses
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationAudi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions
Audi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal
More informationBAER Your Complete Performance Brake Supplier!
Installation Instructions Instruction Part Number: 6000511 Product: Extreme+ / Pro+ Rear Rev Date: 28 January 2015 Vehicle Make: Ford Model: Mustang Year(s): 2015> ATTENTION: Read this before going any
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationAutomotive Service Tools
Automotive Service Tools Part 1 by: Ed Nutter The following document shows the tools that I use to keep my vehicle on the road. You don't have to buy all these tools at once I've been collecting them for
More informationFord Racing Front Lower Control Arms (05-12 GT & GT500):
Ford Racing Front Lower Control Arms (05-12 GT & GT500): Tools needed: Floor jack Jack stands 18mm & 21mm box end wrench 18mm & 21mm socket 13/16 socket (2) Ratchets Breaker bar Torque wrench (0-150 ft/lbs)
More informationCarry out replacement in the following order:
How to replace the rear brake disc on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Replace the brake disks on the car Nissan X-Trail T30 in complete set for each axis. Regardless
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationSpikes-Spider Hub Installation
Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationMustang Steeda Tri-Ax Shifter Installation Guide
Mustang Steeda Tri-Ax Shifter Installation Guide The below installation instructions work for the following products: Mustang Short-Throw Shifters and Mustang Handles This "all questions answered" guide
More informationBBK Electric Mustang Fuel Pump Kit - (86-97 V8) - Installation Instructions
BBK Electric Mustang Fuel Pump Kit - (86-97 V8) - Installation Instructions The below installation instructions work for the following products: BBK Electric Mustang Fuel Pump Kit - 190 LPH (86-97 V8)
More informationSteeda Billet Charge Motion Control Plates (05-08 GT) - Installation Instructions
Steeda Billet Charge Motion Control Plates (05-08 GT) - Installation Instructions The below installation instructions work for the following products: Steeda Billet Charge Motion Control Plates (05-08
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take
More informationInstructional Video Productions and Sales
Instructional Video Productions and Sales Home DVD Info Pictorials Sales Images Updates to DVDs Contact Information R1200 Brake Flush 2007 and newer, and non-abs. Caution: This pictorial is for informational
More informationGP125S STAINLESS HEADER
GP125S STAINLESS HEADER WITH EGR FITTING FORD EXCURSION 6.8L-V-10 2/4WD FORD SUPERDUTY TRUCK F250HD/F350 6.8L-V10 2/4WD GIBSON HEADERS ARE 50 STATE SMOG LEGAL 2/2 WARNING! Do not rely on bumper jacks or
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT BIG BRAKE CONVERSION KIT A112-5 1987-93 FORD MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationREAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
More informationServicing front brakes
46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal
More information