DEMA MODEL 582 FOAM STATION III INSTRUCTION SHEET

Size: px
Start display at page:

Download "DEMA MODEL 582 FOAM STATION III INSTRUCTION SHEET"

Transcription

1 I-866 Pg. 1 of 6

2 1. PURPOSE: The purpose of the DEMA 582 Foam Station III is to allow a remotely located chemical product source (i.e. a tote) to supply up to three DEMA 582 foam stations without the need for a bulky supply container under each foam station. The product tote can be located in a remote location or a secured room. A DEMA MixRite water powered proportioning pump is placed over the tote and mixes the chemical product with water at the correct ratio and sends the mixture through pipes to one or more 582 Foam Stations. The pipes, along with pressurized air hoses, can be run through the walls (if new construction) or run up to the ceiling and dropped back down for connection to the 582 Foam Station III. 2. PARTS / COMPONENTS: A. DEMA Model 582 Foam Station III B Water Outlet Hose 25 long ¾ I.D. (optional) C PVC Foam Wand (optional) D Flow Disc 3. INSTALLATION: Preparation of the 582 location(s) must be made prior to installing this unit. Start with the location of the chemical tote and install a DEMA MixRite pump above the tote. See the DEMA MIXRITE PROPORTIONING PUMP Installation Instruction (I-814). Install a 582 Foam Station III on the wall at each chosen location. Run ½ I.D. (min.) pipe from the MixRite to the 582 location(s). Run pressurized air lines to the 582 location(s). Connect the ½ (or larger) pipe and air lines to each 582 Foam Station III. Connect ¾ ID hose to output (maximum length 50 ft.). 4. OPERATION: Open water inlet ball valve fully. Open air ball valve fully (straight up position). Adjust air pressure regulator until the proper consistency of foam is achieved (40 psi min to 150 psi max). If there is too much foam output you can reduce it by inserting the flow disk into the water inlet as follows: Remove the rubber washer from the water inlet. Insert the flow disk into the water inlet. Refer to the flow disk drawing on page 5 for the correct orientation. Reinsert the rubber washer back into the water inlet. WARNING: If the foam wand valve is shut off while the system is under pressure and the air pressure is higher than the water pressure; soapy water will be forced back into water supply or the pump. To prevent this, shut off the air valve / water valve when not using the unit for any length of time. I-866 Pg. 2 of 6

3 5. SERVICING: PROBLEM CHECK SOLUTION Check for soapy water. Troubleshoot the MixRite unit that Not producing foam. Shake some in a half full bottle to make sure the mixture will fill the other half with foam. supplies soapy water to the 582 Foam Station (See Instruction Sheet I-814). Make sure that the mixture can actually foam. Foam surges. Check for sufficient air. Check that output hose is ¾ ID. Open the air valve and check that air is flowing. If not, check the air compressor. Adjust pressure regulator (40 psi min. up to 150 psi). Adjust the Pressure Regulator. Install ¾ ID hose on output line. 6. OVERALL DIMENSIONS: I-866 Pg. 3 of 6

4 RETURNS / WARRANTY: RETURNS: WARRANTY: NO MERCHANDISE MAY BE RETURNED FOR CREDIT WITHOUT DEMA S WRITTEN PERMISSION. RETURN MERCHANDISE AUTHORIZATION NUMBER REQUIRED IN ADVANCE OF RETURN. DEMA products are warranted against defective material and workmanship under normal use and service for one year from the date of manufacture. This limited warranty does not apply to any products which have a normal life shorter than one year or failure and damage caused by chemicals, corrosion, improper voltage supply, physical abuse, or misapplication. Rubber and synthetic rubber parts such as o - rings, diaphragms, squeeze tubing and gaskets are considered expendable and are not covered under warranty. This warranty is extended only to the original buyer of DEMA products. If products are altered or repaired without prior approval of DEMA, this warranty will be void. Defective units or parts should be returned to the factory with transportation prepaid. If inspection shows them to be defective, they will be repaired or replaced without charge, F.O.B. factory. DEMA assumes no liability for damages. Return merchandise authorization number, to return units for repair or replacement, must be granted in advance of return. I-866 Pg. 4 of 6

5 ITEM NO PART NUMBER DESCRIPTION Pressure Gage ¼ NPT Ball Valve 2A Valve Knob Pressure Regulator ½ NPT PVC Ball Valve Garden Hose Swivel Rubber Washer ½ MPT Hose Adapter Flow Disc I-866 Pg. 5 of 6

6 ITEM NO PART NUMBER DESCRIPTION Foamer Body Air Nozzle V-14 O-ring Spring P-7 7/32 Dia. Teflon Ball V O-ring Washer Internal Snap Ring I-866 Pg. 6 of 6

DEMA Model 294D Spray Foam INSTALLATION INSTRUCTIONS

DEMA Model 294D Spray Foam INSTALLATION INSTRUCTIONS 1. PARTS A. Foamer Assembly B. Plastic chemical supply tubing w/ foot valve and ceramic weight C. Metering tip kit D. Outlet hose 25 long (optional accessory) E. Shut-off valve (optional accessory) 2.

More information

DEMA SPRAY CLEAN MODELS: 241CDF & 241CDFT INSTALLATION INSTRUCTIONS

DEMA SPRAY CLEAN MODELS: 241CDF & 241CDFT INSTALLATION INSTRUCTIONS 1. PARTS A. Bottle holder and injector assembly. B. Spray gun (Model 40-8B). C. 4 mounting screws in envelope. 2. INSTALLATION Mount the bottle holder on wall using the 4 screws provided through the plates

More information

DEMA MODELS P203CTC.PI.1,.2,.3 INSTALLATION INSTRUCTIONS

DEMA MODELS P203CTC.PI.1,.2,.3 INSTALLATION INSTRUCTIONS I. PARTS: A. 1 pc. Cyclone Portable Injector B. 1 pc. Foot Strainer & 1/4" I.D. Tubing. C. 1 pc. Ceramic Weight. D. 1 pc. Instruction Sheet D. 2 pc. 3 hose w/ female x female GHT fittings on both ends

More information

DEMA SPRAY CLEAN MODELS: 244CDF & 244CDFT INSTALLATION INSTRUCTIONS

DEMA SPRAY CLEAN MODELS: 244CDF & 244CDFT INSTALLATION INSTRUCTIONS I. PARTS: A. Injector. B. Spray gun. C. Mounting screws and washers. D. Vinyl supply tubing, foot strainer & ceramic weight. E. Metering tip (specified size, model 244CDFT only). II. INSTALLATION: (See

More information

TABLE 1. * SPECIFY S Stainless Steel Knob Part No S or Part No ST (for tips) for pressure exceeding 700 PSI.

TABLE 1. * SPECIFY S Stainless Steel Knob Part No S or Part No ST (for tips) for pressure exceeding 700 PSI. 1. PARTS A. Injector B. Ceramic Weight. C. Plastic tubing 8' long with foot strainer. 2. INSTALLATION The injector may be installed in any position in the water line with the arrow in the direction of

More information

DEMA MODEL 692T FOAM STATION I INSTALLATION INSTRUCTION

DEMA MODEL 692T FOAM STATION I INSTALLATION INSTRUCTION 1. PARTS CHECKLIST: ITEM DESCRIPTION QTY. A. Foam Station Assembly 1 B. #10 Screw & Anchor Kit Set (Total: 4 Screws & 4 Anchors) 1 C. Ceramic Weight 1 D. ¼ ID Tubing & Foot Valve Assembly 1 E. Metering

More information

DEMA MODEL 603T-WI INSTALLATION INSTRUCTIONS

DEMA MODEL 603T-WI INSTALLATION INSTRUCTIONS DEMA MODEL 603T-WI I. PARTS: A. Select-O-Matic Assembly B. 2 Pcs. Foot Strainers & 1/4" ID Tubing C. 4 Pcs. Mounting Screws & Anchors D. 1 Pc. 100-15K Metering Tip Kit (603T Only) E. 1 Pc. Backflow Preventer

More information

DEMA MODELS 606T INSTALLATION INSTRUCTIONS

DEMA MODELS 606T INSTALLATION INSTRUCTIONS I. PARTS: A. Select-O-Spray Assembly B. 2 Pcs. Foot Strainers & 1/4" ID Tubing C. 4 Pcs. Mounting Screws & Anchors D. 1 Pc. 100-15K Metering Tip Kit TABLE 1 Hose I.D. 3/8" 1/2" 5/8" Max. Length 15 ft.

More information

DEMA MODEL 693T FOAM STATION II INSTALLATION INSTRUCTION

DEMA MODEL 693T FOAM STATION II INSTALLATION INSTRUCTION 1. PARTS CHECKLIST: 2. INSTALLATION: DEMA MODEL 93T FOAM STATION II ITEM DESCRIPTION QTY. A. Foam Station Assembly 1 B. ¼ ID Tubing & Foot Strainer 1 C. 3/ ID Tubing & Foot Strainer 1 D. Ceramic Weight

More information

DEMA MODEL 606T-WI INSTALLATION INSTRUCTIONS

DEMA MODEL 606T-WI INSTALLATION INSTRUCTIONS DEMA MODEL 606T-WI INSTALLATION INSTRUCTIONS I. PARTS: A. Select-O-Spray Assembly B. 2 Pcs. Foot Strainers & 1/4" ID Tubing C. 4 Pcs. Mounting Screws & Anchors D. 1 Pc. 100-15K Metering Tip Kit E. 1 Pc.

More information

DEMA SPRAY CLEAN MODELS: 244BC, 244BCE, 244BCP & 244BCT INSTALLATION INSTRUCTIONS

DEMA SPRAY CLEAN MODELS: 244BC, 244BCE, 244BCP & 244BCT INSTALLATION INSTRUCTIONS I. PARTS: A. Injector. B. Spray gun. C. Mounting screws and washers. D. Vinyl supply tubing, foot strainer & ceramic weight. E. Metering tip (specified size, model 244BCT only). II. INSTALLATION: (See

More information

Spray Clean 606T-2 Installation Instruction

Spray Clean 606T-2 Installation Instruction Spray Clean 606T-2 Installation Instruction Overview The 606T-2 unit is designed to be used as a spray or foam unit where up to two chemicals can be attached to the unit along with a clean water rinse.

More information

DEMA MODEL 604T-WI INSTALLATION INSTRUCTIONS

DEMA MODEL 604T-WI INSTALLATION INSTRUCTIONS DEMA MODEL 604T-WI I. PARTS: A. Select-O-Matic Assembly B. 2 Pcs. Foot Strainers & 1/4" ID Tubing C. 4 Pcs. Mounting Screws & Anchors D. 1 Pc. 100-15K Metering Tip Kit (604T Only) E.1 Pc. Backflow Preventer

More information

DEMA SPRAY STATION II MODEL 606T-2 INSTALLATION INSTRUCTIONS

DEMA SPRAY STATION II MODEL 606T-2 INSTALLATION INSTRUCTIONS The 0T-2 Spray Station II Dispensers are used in any application where a chemical product must be sprayed or foamed without the use of compressed air or a high pressure pump. City water pressure and optional

More information

DEMA SPRAY CLEAN DISPENSERS MODEL 605T INSTALLATION INSTRUCTION

DEMA SPRAY CLEAN DISPENSERS MODEL 605T INSTALLATION INSTRUCTION The 605T Spray Clean Dispenser is used in any application where a chemical product must be sprayed or foamed without the use of compressed air or a high pressure pump. City water pressure and optional

More information

DEMA RAPID FIRE MODELS 6300, , , , 6310, 6300H 6300E, 6300EH, &6310E INSTRUCTION SHEET

DEMA RAPID FIRE MODELS 6300, , , , 6310, 6300H 6300E, 6300EH, &6310E INSTRUCTION SHEET I-1002 Pg. 1 of 12 PURPOSE: The RAPID FIRE is a spray system designed with a single knob to control OFF, RINSE and up to two chemicals using a single chemically resistant plastic injector. There is full

More information

DEMA 652 DUO-FEED INSTALLATION INSTRUCTIONS

DEMA 652 DUO-FEED INSTALLATION INSTRUCTIONS I. PARTS: A. Dispenser assembly B. 1 pc. ½ in I.D. X 6 ft. vinyl outlet tubing C. 1 pc. 9/16 in. I.D. X 6 ft. vinyl outlet tubing. D. 2 pc. 3/8 in. O.D. X 8 ft. vinyl supply tubing, foot valve & ceramic

More information

SINGLE-STAGE INJECTOR MODELS 200-3C, 200C, 201C, 202C, 203C, 204C, 206C, 208C

SINGLE-STAGE INJECTOR MODELS 200-3C, 200C, 201C, 202C, 203C, 204C, 206C, 208C D E M A SINGLE-STAGE MODELS SINGLE-STAGE MODELS 1. PARTS A. Injector B. Backup washer (Models 204C & smaller). C. Ceramic Weight. D. Tubing 8 long w/ foot strainer. E. Three brass nozzle bushings Metering

More information

900-WC OWNER S MANUAL THIS UNIT DOES NOT INCLUDE AWATER BACKFLOW PREVENTER, CHECK LOCAL PLUMBING CODES FOR PROPER INSTALLATION. Pg.

900-WC OWNER S MANUAL THIS UNIT DOES NOT INCLUDE AWATER BACKFLOW PREVENTER, CHECK LOCAL PLUMBING CODES FOR PROPER INSTALLATION. Pg. 900-WC OWNER S MANUAL THIS UNIT DOES NOT INCLUDE AWATER BACKFLOW PREVENTER, CHECK LOCAL PLUMBING CODES FOR PROPER INSTALLATION. Pg. 1 of 6 900-WC FRONT VIEW - CONTROL BOX COVER REMOVED Pg. 2 of 6 04/04/07

More information

DEMA 951 FLUSH MANIFOLD WITH 24V DC VALVE INSTALLATION INSTRUCTIONS

DEMA 951 FLUSH MANIFOLD WITH 24V DC VALVE INSTALLATION INSTRUCTIONS System Overview The DEMA 951 Flush Manifold is designed for long reliable use with simplicity and adaptability in mind. The 951 Flush Manifold can be added to the DEMA Atlas 844P, and DEMA Laundry Master

More information

ALWAYS FOLLOW ALL SAFETY PRECAUTIONS AS DIRECTED BY THE CLEANING CHEMICAL LABEL

ALWAYS FOLLOW ALL SAFETY PRECAUTIONS AS DIRECTED BY THE CLEANING CHEMICAL LABEL Overview (Model # s 4-252- _ ) E2B2 Dispenser The E2B2 dispenser dilutes a concentrated EnvirOx product with water and dispenses the mixture with either a high flow rate (for filling buckets, scrubbers,

More information

WATCH GUARD 440 SERIES FLOAT VALVES INSTALLATION INSTRUCTIONS MODELS: T, TX, T, BT,

WATCH GUARD 440 SERIES FLOAT VALVES INSTALLATION INSTRUCTIONS MODELS: T, TX, T, BT, WATCH GUARD 440 SERIES FLOAT VALVES INSTALLATION INSTRUCTIONS MODELS: 440-22T, 440-22TX, 440-23T, 440-23BT, 440-24 Overview The Watch Guard 440 Series of float valves fills and maintains fluids in reservoirs.

More information

DEMA MIXRITE PROPORTIONING PUMP MODELS 574 & CL & 575CL FOR CORROSIVE LIQUID CHEMICALS INSTALLATION INSTRUCTION.

DEMA MIXRITE PROPORTIONING PUMP MODELS 574 & CL & 575CL FOR CORROSIVE LIQUID CHEMICALS INSTALLATION INSTRUCTION. 10% MixRite Pump I-871 Page 1 MODEL # INDUCTION RANGE%* TECHNICAL DATA TABLE Ability to turn off INDUCTION the chemical flow RANGE RATIO* while water is running OPERATING TEMPERATURE 574 3% to 10% 33/1

More information

Spray & Foam Dispenser Item #

Spray & Foam Dispenser Item # Spray & Foam Dispenser Item #92364-00 Spray & Foam Dispenser Item #92364 Table of Contents Section Page 1. Spray & Foam Dispenser Description... 3 2. Spray & Foam Dispenser Installation... 4 3. Chemical

More information

DEMA 651AG SINGLE-FEED INSTALLATION INSTRUCTIONS

DEMA 651AG SINGLE-FEED INSTALLATION INSTRUCTIONS I. PARTS: A. Dispenser assembly B. 1 pc. 9/16 in. I.D. X 6 ft. vinyl outlet tubing (4 GPM proportioner only). C. 1 pc. 3/8 in. O.D. X 8 ft. vinyl supply tubing, foot valve & ceramic weight. D. 4 pc. #10

More information

DEMA Pro-Fill I Sink Dispenser

DEMA Pro-Fill I Sink Dispenser DEMA Pro-Fill I Sink Dispenser MODELS PF651GAP, PF651AG, PF651GAP-1M, & PF651AG-1M Overview The PRO-FILL I Sink Dispenser mixes water with a cleaning chemical and dispenses the solution into holding containers

More information

The 606T-2 unit is designed to be used as a spray or foam unit where up to two chemicals can be attached to the unit along with a clean water rinse.

The 606T-2 unit is designed to be used as a spray or foam unit where up to two chemicals can be attached to the unit along with a clean water rinse. Overview The 606T-2 unit is designed to be used as a spray or foam unit where up to two chemicals can be attached to the unit along with a clean water rinse. The unit features three ball valves for control

More information

DEMA BLEND CENTER MODELS: 633GAP INSTALLATION INSTRUCTIONS

DEMA BLEND CENTER MODELS: 633GAP INSTALLATION INSTRUCTIONS The 633GAP Series Blend Center modular design lets you easily couple together any number of stations to create a system that meets your specific needs. Mix and match both high and low flow units for filling

More information

DEMA SINGLE-FEED MODEL: 651GAP& 651GAP-1 INSTALLATION INSTRUCTIONS

DEMA SINGLE-FEED MODEL: 651GAP& 651GAP-1 INSTALLATION INSTRUCTIONS The Model 65GAP is designed to dispense one product into a kitchen sink with the turn of a ball valve. I. PARTS: ITEM DESCRIPTION QTY. A Dispenser Assembly B ½ ID X 6 Long Vinyl Outlet Tubing (For 4 GPM

More information

DEMA BLEND CENTER MODELS: 637GAP-1 and 637GAP-4 INSTALLATION INSTRUCTIONS

DEMA BLEND CENTER MODELS: 637GAP-1 and 637GAP-4 INSTALLATION INSTRUCTIONS 1. PARTS CHECKLIST: ITEM DESCRIPTION QTY. A. Blend Center Assembly 1 B. ¼ ID X 8 Long Vinyl Supply Tubing & Foot Valve Assembly 4 C. Ceramic Weight 1 D. ½ ID X 6 Long Vinyl Outlet Tubing (For 1 GPM Station

More information

DEMA Pro-Fill II Sink Dispenser

DEMA Pro-Fill II Sink Dispenser DEMA Pro-Fill II Sink Dispenser MODELS PF652GAP, PF652AG, PF652GAP-2M, & PF652AG-2M Overview The PRO-FILL II Sink Dispenser mixes water with cleaning chemicals and dispenses these solutions. This unit

More information

INSTALLATION INSTRUCTIONS DEMA BLEND CENTER MODEL B-GAP, T-GAP

INSTALLATION INSTRUCTIONS DEMA BLEND CENTER MODEL B-GAP, T-GAP 1. PARTS: ITEM DESCRIPTION QTY. A. Blend Center Assembly 1 B. ¼ ID X 8 Long Vinyl Supply Tubing & Foot Valve Assembly 1 C. Ceramic Weight 1 D. ½ ID X 6 Long Vinyl Outlet Tubing (For 4 GPM Station Only)

More information

1-BUTTON DISPENSER INSTALLATION INSTRUCTIONS

1-BUTTON DISPENSER INSTALLATION INSTRUCTIONS R 1-BUTTON DISPENSER INSTALLATION INSTRUCTIONS Model: #91162-00 The Green Earth II 1-button dispenser allows you to dispense one product for mop buckets and automatic scrubbers. The modular design lets

More information

DEMA 259B DRAIN MASTER Jr. INSTALLATION INSTRUCTION SHEET

DEMA 259B DRAIN MASTER Jr. INSTALLATION INSTRUCTION SHEET I-707 Pg. 1 of 7 Summary The 259B Drain Master is designed to feed chemicals into drains and grease traps to break up grease, detergent build up and eliminate odors. All programming is done by use of a

More information

DEMA BLEND CENTER MODEL 681GAP-3 INSTALLATION INSTRUCTIONS

DEMA BLEND CENTER MODEL 681GAP-3 INSTALLATION INSTRUCTIONS 1. PARTS CHECKLIST: A. Blend Center Assembly B. Vinyl Supply Tubing with Foot Valve Assembly C. Ceramic Weight D. Vinyl Outlet Tubing E. Screw and Anchor Kit F. Label Card G. Metering Tip Kit 2. INSTALLATION:

More information

TABLE 1-1 GPM FLOW RATE PROPORTIONER, 1/4 I.D. TUBING Injection Rates For Viscosities Shown Metering Tip Color

TABLE 1-1 GPM FLOW RATE PROPORTIONER, 1/4 I.D. TUBING Injection Rates For Viscosities Shown Metering Tip Color Blend Safe II Dispensing System is a modular, locking dispensing system that allows user to dispense chemicals safely, control dispenser inventory and has the flexibility in the field to meet changing

More information

PeroxiDraw Dispenser

PeroxiDraw Dispenser The PeroxiDraw Dispensing System is a locking dispensing system that allows the user to dispense Green Earth Peroxide Cleaner for up to six different dilutions and applications safely and effectively.

More information

Caution! Pg. 1 of 5 I-932

Caution! Pg. 1 of 5 I-932 Pg. 1 of 5 PFN26-SS BA25 QF1438 QFT38 CT38-15 DFP6 AW14 AW316 AHB14 AHB316 BA25 AP25 TANK 10 FOG-MAST DPN-10 DPG-10 DP-10 HBEL1238 PL10-B HBSS1212 W10 SSAXLE12 AXC12 SHW3 HB1438 STR14 SIDE VIEW Pg. 2 of

More information

Items # and #

Items # and # D I S P E N S E R T E C H N I C A L M A N U A L Items #91160-00 and #91161-00 1. System Description... 1 2. Equipment Included with the Green Earth II XL System... 2 3. Components Included with Green Earth

More information

DART Ware Wash Speed Control

DART Ware Wash Speed Control DART Ware Wash Speed Control Overview Simple and value best describe the DEMA Dart. The system is extremely easy to setup and program. The Dart is suitable to deliver detergent, rinse aid and sanitizer

More information

DEMA DILUTION-AT-HAND EXTREME 800 Series Chemical Dispensers

DEMA DILUTION-AT-HAND EXTREME 800 Series Chemical Dispensers DEMA DILUTION-AT-HAND EXTREME 800 Series Chemical Dispensers Overview The DILUTION-AT-HAND EXTREME chemical dispenser series combines the proven technology of the DEMA DILUTION-AT-HAND with a new look

More information

I Button Chemical Dispenser. Overview. Installation Instructions

I Button Chemical Dispenser. Overview. Installation Instructions 4 Button Chemical Dispenser Overview The 4 Button Chemical Dispenser makes users more efficient, filling bottles and buckets with ease and quickness. Package Contains: Mounting Template Mounting hardware

More information

23200 Navigator Dilution Control System 4 Button Model (NAV 4)

23200 Navigator Dilution Control System 4 Button Model (NAV 4) 23200 Navigator Dilution Control System 4 Button Model (NAV 4) Overview The NAV 4 Chemical Dilution Control System accurately dilutes cleaning chemicals from cleaning concentrate product. It is a closed

More information

Trident Laundry Chemical Delivery System

Trident Laundry Chemical Delivery System Trident Laundry Chemical Delivery System Installation and Setup Guide The DEMA Trident is a complete laundry chemical delivery system for commercial laundry applications. The Trident features Bluetooth

More information

DEMA 258BD-200C and 258BT-200C DRAIN MASTER Jr. INSTALLATION INSTRUCTION SHEET

DEMA 258BD-200C and 258BT-200C DRAIN MASTER Jr. INSTALLATION INSTRUCTION SHEET I-736 Pg. 1 of 10 Summary The 258BD-200C Drain Master is designed to feed chemicals into drains and grease traps to break up grease, detergent buildup and eliminate odors. The 258BT-200C Trash Master is

More information

DEMA SINGLE PRODUCT LAUNDRY MASTER TM W/BLEACH OPTION INSTALLATION INSTRUCTIONS LIQUID MODEL 840 (B)(S)

DEMA SINGLE PRODUCT LAUNDRY MASTER TM W/BLEACH OPTION INSTALLATION INSTRUCTIONS LIQUID MODEL 840 (B)(S) LIQUID MODEL 840 (B)(S) DEMA Engineering Company 10020 Big Bend Blvd. St. Louis, MO 63122 (800) 325-3362 or (314) 966-3533 www.demaeng.com Rev B-34251 2/27/09 Page 1 of 11 LIQUID MODEL 840 (B)(S) Model

More information

DEMAMaster TM DM-811 Series Installation Manual

DEMAMaster TM DM-811 Series Installation Manual R TM MADE IN USA I-807 Page 1 of 6 System Overview The DEMAMaster series is designed for long reliable use with simplicity in mind for both the installer and user. The DEMAMaster dispenses using the reliable

More information

DEMA S.U.D.S Jr. SINGLE PRODUCT LAUNDRY 581K(I)(S)(V)

DEMA S.U.D.S Jr. SINGLE PRODUCT LAUNDRY 581K(I)(S)(V) DEMA S.U.D.S Jr. SINGLE PRODUCT LAUNDRY 581K(I)(S)(V) Overview The DEMA 581K SUDS Jr. Single Product Solid Laundry system has been updated and redesigned. It uses the proven DEMA Viking Bowl and removes

More information

D EMA TWO-STAGE INJECTOR MODELS 233, 234A, 236A, 236-8, 238, AND 2312 INSTALLATION INSTRUCTIONS FIGURE 3 FIGURE 2

D EMA TWO-STAGE INJECTOR MODELS 233, 234A, 236A, 236-8, 238, AND 2312 INSTALLATION INSTRUCTIONS FIGURE 3 FIGURE 2 1. PARTS A. Injector B. Three brass nozzle bushings. C. Plastic Tubing 8 long with foot strainer. D. Ceramic Weight 2. INSTALLATION A. Selecting the nozzle bushing: Refer to Section 4 APPLICATIONS and

More information

910 BHF OWNER S MANUAL. Pg. 1 of 9

910 BHF OWNER S MANUAL. Pg. 1 of 9 OWNER S MANUAL Pg. 1 of 9 DFP6 TANK 10 HHPB1214 QF14P QFSEL14 QF1238 QFSEL38 PL10-CH QFA3838 DPN-10 DPG-10 DP-10 HBEL1238 H38B W10 SSAXLE12 AXC12 SHW3 FV2 Pg. 2 of 9 PSG-BRKT ICS-12V BC23-12V-A BC23-12V

More information

Trapper Drain Maintenance/Odor Control Chemical Dispensing

Trapper Drain Maintenance/Odor Control Chemical Dispensing Trapper Drain Maintenance/Odor Control Chemical Dispensing Overview The DEMA Trapper is a digital chemical dispenser that is designed to deliver chemicals for both drain and odor control. The system will

More information

665 Series Dispenser. Metering tip kit

665 Series Dispenser. Metering tip kit 665 Series Dispenser Metering tip kit Box Contains Mounting hardware, template & key set Instruction sheet 665 series dispenser 4 SafeLink cap assemblies OR Bulk tubing, 4 ceramic weights and foot valves

More information

DEMA SQUIRT DRAIN UNIT

DEMA SQUIRT DRAIN UNIT DEMA SQUIRT DRAIN UNIT Overview The Squirt is a chemical dispenser with a programmable timer designed primarily for dispensing chemicals into drains. Its most clear intended use is for drain applications

More information

ALWAYS DISCONNECT DISPENSER FROM WATER SOURCE WHEN DISPENSER IS NOT IN USE.

ALWAYS DISCONNECT DISPENSER FROM WATER SOURCE WHEN DISPENSER IS NOT IN USE. 1060GAPRF With dilution selector 1060GAP OVERVIEW DEMA S MPD is a multiple product and dilution dispenser designed for use with SafeLink closed loop inserts. With its innovative patent pending QuickDock

More information

DEMA Nitro for Europe Ware Wash Chemical Dispensing

DEMA Nitro for Europe Ware Wash Chemical Dispensing DEMA Nitro for Europe Ware Wash Chemical Dispensing Overview The DEMA Nitro is a digital ware wash dispenser designed to dispense cleaning chemicals when signals are received from ware wash and dish machines.

More information

BIOACTIVE SOLUTIONS AC DRAIN STATION

BIOACTIVE SOLUTIONS AC DRAIN STATION BIOACTIVE SOLUTIONS AC DRAIN STATION 98488-00 Overview The BioActive Solutions Drain Station is a chemical dispenser with a programmable timer designed primarily for dispensing chemicals into drains. Its

More information

Drain Chief Plus Drain Maintenance/Odor Control Chemical Dispensing

Drain Chief Plus Drain Maintenance/Odor Control Chemical Dispensing Drain Chief Plus Drain Maintenance/Odor Control Chemical Dispensing Overview The VIKING Drain Chief Plus is a digital chemical dispenser that is designed to deliver chemicals for both drain and odor control.

More information

Certo Chemical Dilution System

Certo Chemical Dilution System Certo Chemical Dilution System Overview The Certo Chemical Dilution System accurately dilutes chemical concentrates with water and dispenses the diluted mixture at either a high flow rate to fill buckets

More information

PRO IV LIQUID DETERGENT & LIQUID RINSE DISPENSER INSTALLATION INSTRUCTIONS REVISION #5

PRO IV LIQUID DETERGENT & LIQUID RINSE DISPENSER INSTALLATION INSTRUCTIONS REVISION #5 PRO IV LIQUID DETERGENT & LIQUID RINSE DISPENSER INSTALLATION INSTRUCTIONS REVISION #5 STEP #1. MOUNTING 1. Choose a location where the unit is visible to the machine operator. 2. Locate the unit out of

More information

DEMA Dispensing. Overview. Warnings. I-1205 Rev. B a digital ware. The DEMA. Nitro Plus is. tee.

DEMA Dispensing. Overview. Warnings. I-1205 Rev. B a digital ware. The DEMA. Nitro Plus is. tee. DEMA Nitro Plus Ware Wash Chemical Dispensing Overview The DEMA Nitro Plus is a digital ware wash dispenser designed to dispense cleaning chemicals into ware wash and dish machines. The unit is triggered

More information

Intended Use: Explanation of Signal Word Consequences

Intended Use: Explanation of Signal Word Consequences SAFETY INFORMATION & INSTRUCTION MANUAL Please read, understand, and follow all safety information contained in these instructions prior to the use of this device. Retain these instructions for future

More information

BLAST-TEC PRO - ROTATING TURBO NOZZLES

BLAST-TEC PRO - ROTATING TURBO NOZZLES BLAST-TEC PRO - ROTATING TURBO NOZZLES BLAST-TEC PRO ROTATING TURBO NOZZLE - 1000 PSI The Blast-Tec Pro was designed specifically for high-pressure, high-impact vehicle wash applications including wheel

More information

DEMA 257C / 257CV PRO BATTERY DRAIN CHIEF INSTALLATION & OPERATING INSTRUCTIONS

DEMA 257C / 257CV PRO BATTERY DRAIN CHIEF INSTALLATION & OPERATING INSTRUCTIONS DEMA 257C / 257CV PRO BATTERY DRAIN CHIEF INSTALLATION & OPERATING INSTRUCTIONS Note This dispenser is designed for injecting drain and grease trap products in locations where an outlet isn t available.

More information

Foam Output 50 gal/min (190 ltr/min) 65 gal/min (246 ltr/min) Foaming Distance 30 feet (9 meters) 35 feet (10 meters) alcohols, ketones.

Foam Output 50 gal/min (190 ltr/min) 65 gal/min (246 ltr/min) Foaming Distance 30 feet (9 meters) 35 feet (10 meters) alcohols, ketones. INSTRUCTION MANUAL INTRODUCTION Foam cleaning is recognized as an effective method for removing oil and heavy soils from all types of surfaces. It is used for cleaning throughout the food processing, dairy,

More information

SAFETY INFORMATION & INSTRUCTION MANUAL

SAFETY INFORMATION & INSTRUCTION MANUAL SAFETY INFORMATION & INSTRUCTION MANUAL Please read, understand, and follow all safety information contained in these instructions prior to the use of this device. Retain these instructions for future

More information

MACHINES / RECLAIMS WITH DUST BAG

MACHINES / RECLAIMS WITH DUST BAG WARNING SET-UP INSTRUCTIONS MACHINES / RECLAIMS WITH DUST BAG *** READ BEFORE OPERATING EQUIPMENT *** 1. Remove plastic from machine. 2. Remove lag bolts from each of the four legs, then remove machine

More information

Dual Phase Extraction Inlet. Patent No Installation Manual. P/N Rev

Dual Phase Extraction Inlet. Patent No Installation Manual. P/N Rev Patent No. 6520259 Installation Manual P/N 95232 Rev 6-16-11 Table of Contents ing Extraction Inlets track changing water levels to maintain optimum performance 1.Component Identification Page 1 2. How

More information

INSTALLATION INSTRUCTIONS. PART NUMBER C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo

INSTALLATION INSTRUCTIONS. PART NUMBER C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo INSTALLATION INSTRUCTIONS PART NUMBER 26-3002C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 08483K HOSE CLAMP #28, BLACK ZINC PLATED 2 2 5-1070 COUPLER;1.75-2.50X3.25"

More information

SWING JOINT & HEAVY TURF

SWING JOINT & HEAVY TURF PRICE GROUP DESCRIPTION 11 SWING JOINT 08 HEAVY TURF DISCOUNT MULTIPLIER PRODUCTS SWING JOINT & HEAVY TURF IRRIGATION FITTINGS INCLUDES: PVC SWING JOINTS AND IRRIGATION ACCESSORIES LSJHT EFFECTIVE JULY

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS BMW 335i 3.0L

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS BMW 335i 3.0L Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS 2012-2015 BMW 335i 3.0L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2057DK AIR FILTER 1 2 9-0442 TUBE;

More information

Reference Manual FM-200 Series

Reference Manual FM-200 Series Flush Manifold A/P FOR LIQUID LAUNDRY SUPPLY SYSTEMS Reference Manual FM-200 Series Copyright 2004 Nova Controls, Inc. P/N 20-07941-00 Rev. C i P/N 20-07941-00 Rev. C ii P/N 20-07941-00 Rev. C 1 Description

More information

SOLUTION STATION Instruction Manual

SOLUTION STATION Instruction Manual SOLUTION STATION Instruction Manual WAXIE Sanitary Supply 9353 WAXIE Way San Diego, CA 92123 Phone: 800.995.4466 www.waxie.com TABLE OF CONTENTS Unpacking Instructions Disclaimer..... Warranty... Introduction...

More information

DIRECT-DRIVE PRESSURE WASHERS

DIRECT-DRIVE PRESSURE WASHERS DIRECT-DRIVE PRESSURE WASHERS PJG SERIES PRESSURE WASHER MANUFACTURED BY: PJG-2002B PJG-2502-6.5B PJG-3002B PJG-4002B INTRODUCTION Thank you for purchasing a Mancorp Pressure Washer. This manual covers

More information

DMV 2D Self Rotating Nozzle

DMV 2D Self Rotating Nozzle DMV 2D Self Rotating Nozzle for Downhole Applications W A T E R J E T T O O L S Hydropulsion Ltd. www.hydropulsion.com Phone +44 (0)1224 200125, Fax +44 (0)1224 515010 email orders: sales@hydropulsion.com

More information

S P R AY E R VA L V E S AND C O N T ROL S C AT A L OG

S P R AY E R VA L V E S AND C O N T ROL S C AT A L OG Q UA L I T Y VA LV E S A N D C O N T R O L S. TO D AY A N D TO M O R R O W. Texas Industrial Remcor, Inc. CATALOG NO. 33 The new RC2 control system: Ensures no potential leaks in the tractor cab when using

More information

Parts Manual V100G Vacuum Machine Part #E (SERIAL #1G G )

Parts Manual V100G Vacuum Machine Part #E (SERIAL #1G G ) 2006 Perimeter Road. Greenville, SC 29605 Toll Free: 800/435-9340 - Phone: 864/277-5870 Fax: 864/235-9661 - Website address: www.mightymole.com Email address: mmole@mightymole.com Parts Manual V100G Vacuum

More information

Crescent Flush Manifold FOR LIQUID LAUNDRY SUPPLY SYSTEMS

Crescent Flush Manifold FOR LIQUID LAUNDRY SUPPLY SYSTEMS Crescent Flush Manifold FOR LIQUID LAUNDRY SUPPLY SYSTEMS Reference Manual FM-300 Series Copyright 2005 Nova Controls, Inc. P/N 20-08195-00 Rev. B i ii 1 Description Overview The FM-300 series Flush Manifold

More information

Techcon Systems TS5620 Series Diaphragm Valve. User Guide

Techcon Systems TS5620 Series Diaphragm Valve. User Guide Techcon Systems TS5620 Series Diaphragm Valve User Guide CONTENTS Page number 1. Specifications - Horizontal Valve. 3 2. Specifications -Vertical Valve.. 4 3. Unpacking and Inspection 5 4. Description........5

More information

PARTS AND INSTALLATION MANUAL

PARTS AND INSTALLATION MANUAL PSP-3240 POLYPROPYLENE SELF-PRIMING 2 CENTRIFUGAL PUMP PARTS AND INSTALLATION MANUAL PSP-3240 Shown with GX-160 Honda CDS-JOHN BLUE COMPANY DIVISION OF ADVANCED SYSTEMS TECHNOLOGY, INC. 165 Electronics

More information

AUTO-PUMP 120 VAC AIR COMPRESSOR SYSTEM INSTRUCTION MANUAL. 170 Cherry Avenue West Sayville, NY

AUTO-PUMP 120 VAC AIR COMPRESSOR SYSTEM INSTRUCTION MANUAL. 170 Cherry Avenue West Sayville, NY INSTRUCTION MANUAL AUTO-PUMP 120 VAC AIR COMPRESSOR SYSTEM MODEL #: #:091-9B-1 091-9B-1 INPUT :120 volt, 50/60 Hz, 1.8 AMPS OUTPUT: 100 PSI MAXIMUM File: 091-9B-1_revA1_GEN3 Rev: A1 Revised By:PSS/JRN

More information

Parts Manual V100G Vacuum Machine Part #E (SERIAL #1G G )

Parts Manual V100G Vacuum Machine Part #E (SERIAL #1G G ) 2006 Perimeter Road. Greenville, SC 29605 Toll Free: 800/435-9340 - Phone: 864/277-5870 Fax: 864/235-9661 - Website address: www.mightymole.com Email address: mmole@mightymole.com Parts Manual V100G Vacuum

More information

LBT-3 WITH 300 CFM RECLAIM MANUAL NUMBER: 506 TABLE OF CONTENTS

LBT-3 WITH 300 CFM RECLAIM MANUAL NUMBER: 506 TABLE OF CONTENTS LITTLE BLASTER LITTLE BLASTER LBT-3 WITH 300 CFM RECLAIM MANUAL NUMBER: 506 TABLE OF CONTENTS PAGE FIGURE 1 - SET-UP INSTRUCTIONS 1 - OPERATING INSTRUCTIONS 1 - GENERAL MAINTENANCE 2 1 STANDARD CABINET

More information

SCHEDULE 80 PVC PRESSURE FITTINGS L80P EFFECTIVE JULY 1, 2017 REVISED PRODUCTS PRICE LIST INCLUDES: SCHEDULE 80 PVC 1/4 TO 12

SCHEDULE 80 PVC PRESSURE FITTINGS L80P EFFECTIVE JULY 1, 2017 REVISED PRODUCTS PRICE LIST INCLUDES: SCHEDULE 80 PVC 1/4 TO 12 PRICE GROUP DESCRIPTION 02 SCH 80 PVC through 8 92 SCH 80 PVC 10" AND LARGER VB GASKET for FLANGE DISCOUNT MULTIPLIER PRODUCTS SCHEDULE 80 PVC PRESSURE FITTINGS INCLUDES: SCHEDULE 80 PVC 1/4 TO 12 L80P

More information

HIGH PRESSURE AIR COMPRESSOR SYSTEM MODEL #: 091-9HP-220 INPUT:

HIGH PRESSURE AIR COMPRESSOR SYSTEM MODEL #: 091-9HP-220 INPUT: INSTRUCTION MANUAL AUTO-PUMP HP 240 VAC HIGH PRESSURE AIR COMPRESSOR SYSTEM MODEL #: 091-9HP-220 INPUT: 220-240 Vac, 50 Hz, 1.3 Amps 230 Vac, 60 Hz, 1.2 Amps File: IM_091-9HP-220-RevB2.indd Rev: B2 Revised

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) 2016 VW Jetta 1.

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) 2016 VW Jetta 1. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-797C (GUN METAL GRAY FINISH) 2016 VW Jetta 1.4T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 2-1578C TUBE; 3.25"D

More information

Hose reels for diesel exhaust fluid (DEF)

Hose reels for diesel exhaust fluid (DEF) Installation and maintenance guide Hose reels for diesel exhaust fluid (DEF) Models 85700-30 and 85700-50 Date of issue January 2015 Form number 404381C Section E35 Page 78C DANGER Read manual prior to

More information

BLAST-TEC PRO. Rotating Turbo Nozzles. Optimization & Troubleshooting Guide REV C revc0118

BLAST-TEC PRO. Rotating Turbo Nozzles. Optimization & Troubleshooting Guide REV C revc0118 BLAST-TEC PRO Rotating Turbo Nozzles Optimization & Troubleshooting Guide REV C 4000002 revc08 Hydra-Flex, Hydra-Flex, Inc. 208 Inc. 208 TABLE OF CONTENTS Product Overview Product Line Description Specifications

More information

WATERBLAST HOSE REEL SYSTEM HWB HOSE REEL OPERATION AND MAINTENANCE MANUAL W A T E R J E T T O O L S

WATERBLAST HOSE REEL SYSTEM HWB HOSE REEL OPERATION AND MAINTENANCE MANUAL W A T E R J E T T O O L S WATERBLAST HOSE REEL SYSTEM HWB HOSE REEL OPERATION AND MAINTENANCE MANUAL W A T E R J E T T O O L S 466 S. SKYLANE DR. DURANGO, COLORADO 81303 970-259-2869 PHONE 970-259-2868 FAX www.stoneagetools.com

More information

Versa Stainless Wash System

Versa Stainless Wash System Versa Stainless Wash System Introduction Congratulations on your purchase of the Ginsan Versa Stainless Wash System. Ginsan's Versa Stainless Wash System is designed specifically to meet the needs of the

More information

DP DIAPHRAGM PUMP Parts & Instruction Manual

DP DIAPHRAGM PUMP Parts & Instruction Manual DP-392.1 DIAPHRAGM PUMP Parts & Instruction Manual Price $10.00 CDS-JOHN BLUE COMPANY DIVISION OF ADVANCED SYSTEMS TECHNOLOGY, INC. 290 Pinehurst Drive Huntsville, Alabama 35806 P. O. Box 1607 Huntsville,

More information

SUPER SEALCOATER 550 & 800 PARTS MANUAL REV. B

SUPER SEALCOATER 550 & 800 PARTS MANUAL REV. B SUPER SEALCOATER 550 & 800 PARTS MANUAL 709 REV. B Fill in appropriate fields that apply to this machine. Machine S/N: st Hose S/N: nd Hose S/N: st Pump S/N: nd Pump S/N: Engine S/N: Compressor S/N: Gear

More information

Operating and Maintenance Instructions

Operating and Maintenance Instructions 1500 Tube Leak Test Gun - Vacuum Tube & Pipe Cleaners Tube Testers Tube Plugs Tube Removal Tube Installation Operating and Maintenance Instructions www.elliott-tool.com Table Of Contents Introduction...

More information

INSTALLATION INSTRUCTIONS PART NUMBER WR (Wrinkle Red Finish)

INSTALLATION INSTRUCTIONS PART NUMBER WR (Wrinkle Red Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-746WR (Wrinkle Red Finish) 2015-17 VOLKSWAGEN GOLF 1.8/2.0L 2015-17 VOLKSWAGEN GTI 2.0L 2015-16 VOLKSWAGEN GOLF

More information

Owner s Manual Nitrate Series Salt Based Filter System

Owner s Manual Nitrate Series Salt Based Filter System Owner s Manual Nitrate Series Salt Based Filter System Page 2 Copyright 2012 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems.

More information

Model 6518FR. NOTE TO INSTALLER: Please leave this information with the Maintenance Department. LIMITED WARRANTY

Model 6518FR. NOTE TO INSTALLER: Please leave this information with the Maintenance Department. LIMITED WARRANTY INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model 6518FR No. 2077777(21)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-783C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6L TURBO C.A.R.B. E.O# D-670-24 2017 HYUNDAI TUCSON 1.6L TURBO

More information

QUANTUM SERIES JUICE DISPENSER

QUANTUM SERIES JUICE DISPENSER QUANTUM SERIES JUICE DISPENSER l IPL Manual Release Date: April 25, 2001 Publication Number: 720901120IPL Revision Date: April 28, 2014 Revision: C Visit the Cornelius web site at www.cornelius.com for

More information

Techcon Systems TS5322 TS5322D Adjustable Mini Spool Valve. User Guide

Techcon Systems TS5322 TS5322D Adjustable Mini Spool Valve. User Guide Techcon Systems TS5322 TS5322D Adjustable Mini Spool Valve User Guide CONTENTS Page number 1. Specifications..... 3 2. Unpacking and Inspection.... 4 3. Description........4 4. Theory of Operation.. 4

More information

INSTALLATION INSTRUCTIONS PART NUMBER: DC

INSTALLATION INSTRUCTIONS PART NUMBER: DC Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8033DC 2014-16 Chevrolet Silverado 1500 5.3L/6.2L C.A.R.B. E.O. # D-670-23 2014-16 GMC Sierra 1500 5.3L/6.2L

More information

ILLUSTRATED PARTS LIST

ILLUSTRATED PARTS LIST Anoka, MN. 0- Telephone -00--00 Facsimile -00--0 FCB POST-MIX DISPENSER WITH HOT-GAS DEFROST AND V ELECTRONICS (DEFROST/ERROR INDICATOR LIGHTS) UNIT PART NO. 0000 000 THIS DOCUMENT CONTAINS IMPORTANT INFORMATION

More information