(MLV) MULTILAYER CHIP VARISTOR

Size: px
Start display at page:

Download "(MLV) MULTILAYER CHIP VARISTOR"

Transcription

1 (MV) MUTIAYER CHIP VARISTOR MV <0.5ns ESD Multilayer Chip s (MV) are Transient Suppressors (TVS) which manufactured from semicon ductingceramics by the highly advanced multilayer formation technologies, which can offer rugged protection, excellent transient energy absorption and internal heat dissipation. The devices are leadless chip form, eliminating lead inductance and guaranteeing a faster speed of response time of less than 0.5ns, which makes the m fast enough to ensure reliable protection against ESD pulse and other specific transient events. These transient suppression devices are significantly smaller footprints and lower profiles than traditional zener diodes or radial MOVs. Multilayer Formation Technologies FEATURES Section of the chip 05[02] 1[03] [005] 32[] 35[] 2[] 5750[] 063[35] 0[32] eadless 05[02], 1[03], [005], 32[], 35[], 2[], 063[35] and 0[32] Chip Size to +5 Operating Temperature Range Vw(dc) V Operating Range Vw(DC) =3.3V to 615V ESD Inherent Bi-directional Very ow eakage <0.5ns ow Inductance, Fast Response (Response time<0.5ns) Excellent Temperature Coefficient / / Good Solderability (The electrode termination is selectable in plated and silver /palladium/platinum.)

2 MV INTRODUCTION FO FPV SERIES MUTIAYER INFORMATION FOR DESIGNER Dependent Characteristic Transient Suppressors (s) are -dependent electrical resistors with symmetrical V/I characteristic. Their resistance value decrease with increasing, thus "short-circuiting" further rises in over. TERMS AND DESCRIPTIONS Working DC (Vw(DC)) This is the maximum continuous DC, which may be applied up to the maximum operating temperature of the device. The rated DC operating (working ) is also used as the reference point for leakage current. This is always less than the breakdown of the device. Working AC (Vw(AC)) This is the maximum continuous sinusoidal rms, which maybe applied at any temperature up to the maximum operating temperature of the device. Surge ( IP ) (/ s) This is the maximum peak current, which may be applied for an / s impulse, with rated line also applied, without causing device failure. The pulse can be applied to the device in either polarity with the same confidence factor. ( E S) Surge (Es) /00 s This is the maximum rated transient energy which may be dissipated for a single current pulse at a specified impulse duration (/00 s), with the rated DC or RMS applied, without causing device failure. I leakage (I ) at Rated DC ( <50 A) A In the no conducting mode, the device is at a very high impedance (approaching ohms) andappears as an almost open circuit in the system. The leakage current drawn at this level is very low(<50 A at ambient temperature) and, unlike the zener diode, the multilayer varistors have the added advantage that, when operated up to its maximum temperature, its leakage current will not increase above A. ((DC)) 1mA This is the at which the device changes from the off state to the on state and enters its conduction mode of operation. The is usually characterized at the 1mA point. (Vc) / s This is the peak appearing across the suppressor when measured at conditions of specified pulse current and specified waveform (/ s). It is important to note that the peak current and peak may not necessarily be coincidental in time. (Cp) 1MHz 0.5V This is the capacitance of the device at a specified frequency 1MHz and bias 0.5V

3 APPICATION The Prevention of Over When the increases above the threshold of MV, the suppressor will draws a rapidly increasing current, and then the over is considerably attenuated away from the protection of the equipments should be supplemented by including specific components that will raise the withstand capabilities to the required level. s provide protection against all kind of overv oltage and prevent electronic equipment from being damaged by transient events. Specific Application EFT Suppression of Inductive Switching or Other Transient Events Such as EFT and Surge at the Circuit Board evel. ESD Protection of Components and Circuits Sensitive to ESD Transients Occurring on Power supplies, Control and Signal ines. IC CMOS MOSFET Provides On-Board Transient Protection for ICs, CMOS and MOSFET. TVS Replace arger Surface Mount TVS Zeners in Many Applications Used to Help Achieve Electromagnetic Compliance of End Products Multilayer Chip PART NUMBER IDENTIFICATION FPV 10 G 3R3 P M T Product Code FPV Multilayer Chip ( W T) (mm) Dimensions Product Series E S G High energy absorb type High speed type General type Working DC 3R V V Termination P S Plated Non-plated Pt/Pd/Ag Tolerance M % Packaging Style T B Tape & Reel Bulk

4 MV INTRODUCTION FO FPV SERIES MUTIAYER SHAPE AND DIMENSIONS & EQUIVAENT CIRCUIT (Unit): mm/inch Part Number W T D (02) ( ) ( ) ( ) ( ) (03) ( ) ( ) ( ) ( ) (005) ( ) ( ) ( ) ( ) (005) ( ) ( ) ( ) ( ) Equivalent circuit 32 () ( 0.00) ( ) ( ) 0.5 ( ) () ( 0.00) ( ) ( ) ( ) () ( 0.00) ( ) (1 0.00) ( ) (06) (6 0.00) ( ) ( ) ( ) 215 () (0 0.00) ( 0.00) 0.2 ( ) 0.5 ( ) ~ 0.7 (0. 0.0) (0. 0.0) (0~0.0) ( ) ~ (2 0.0) (0. 0.0) (0~0.0) ( ) ~ ( ) ( 0.0) (0~0.0) ( ) SPECIFICATION Multilayer Chip General Series FPV General Series is a major series of FPV Mulitlayer Chip s (MV), which can provide widely working, high reliability and suppress varies transient event IC l Protection from transient noise in all kinds of IC I/O ESD EFT l Protection from ESD, EFT and surge in power I/O port l Replacement of zener diode 05 (02) TYPE Working 05 DC AC / s 1A /00 s / s FPV0505G3R3 M % 0 FPV0505G5R6 1 FPV0505GR FPV0505GR FPV0505G FPV0505G1.5 3 FPV0505G1 1 FPV0505G FPV0505G0 0

5 1 (03) TYPE Working 1 DC AC / s 1A /00 s / s FPV10G3R3 FPV10G5R6 FPV10GR0 FPV10GR0 FPV10G1 FPV10G1 FPV10G1 FPV10G1 FPV10G0 FPV10G2 FPV10G2 FPV10G2 FPV10G0 M % (005) TYPE Working DC AC / s 1A /00 s / s FPV G3R3 M FPV G5R6 FPV GR0 FPV GR0 FPV G1 FPV G1 FPV G1 FPV G1 FPV G0 FPV G2 FPV G2 FPV G2 FPV G %

6 MV INTRODUCTION FO FPV SERIES MUTIAYER 32() TYPE 32 Working DC AC / s 1A /00 s / s FPV32 G3R3 M % 0 FPV32 G5R6 1 5 FPV32 GR0 FPV32 GR0 FPV32 G1 FPV32 G1 FPV32 G1 FPV32 G1 FPV32 G0 FPV32 G2 FPV32 G2 FPV32 G2 FPV32 G0 FPV32 G3 FPV32 G30 FPV32 G FPV32 G0 FPV32 G5 FPV32 G0 FPV32 G MUTAYER CHIP VARISTOR HIGH ENERGY ABSORB SERIES High Series is design to absorb the high energy transient in circuit, which provide high rate current, highly energy absorb ability and fast response speed Application EFT Suppression of Inductive Switching or Other Transient Events Such as EFT and Surge at the Circuit Board evel. ESD Protection of Components and Circuits Sensitive to ESD Transients Occurring on Power supplies, Control and Signal ines. IC CMOS MOSFET Provides On-Board Transient Protection for ICs, CMOS and MOSFET. TVS Replace arger Surface Mount TVS Zeners in Many Applications

7 (005) TYPE Working DC AC / s 1A /00 s / s FPV E3R3 M FPV E5R6 FPV ER0 FPV ER0 FPV E1 FPV E1 FPV E1 FPV E1 FPV E0 FPV E2 FPV E2 FPV E2 FPV E V B % () TYPE Working 32 DC AC / s 1A /00 s / s FPV32 E3R3 M % 10 FPV32 E5R FPV32 ER FPV32 ER FPV32 E FPV32 E FPV32 E1 5 FPV32 E FPV32 E0 FPV32 E2 1 FPV32 E FPV32 E FPV32 E FPV32 E FPV32 E FPV32 E FPV32 E FPV32 E5 FPV32 E0 FPV32 E

8 MV INTRODUCTION FO FPV SERIES MUTIAYER 35() TYPE 35 Working DC AC / s 1A /00 s / s FPV35 E0 FPV35 E2 FPV35 E2 FPV35 E2 FPV35 E0 FPV35 E3 FPV35 E30 FPV35 E FPV35 E0 FPV35 E5 FPV35 E0 FPV35 E () TYPE 2 Working DC AC / s 1A /00 s / s FPV215E0 FPV215E2 FPV215E2 FPV215E2 FPV215E0 FPV215E3 FPV215E30 FPV215E FPV215E0 FPV215E5 FPV215E0 FPV215E TYPE 5750 FPV5750E0 FPV5750E2 FPV5750E2 FPV5750E2 FPV5750E0 FPV5750E3 FPV5750E30 FPV5750E FPV5750E0 FPV5750E5 FPV5750E0 FPV5750E60 Working DC AC / s 1A /00 s / s

9 Working DC AC / s 1A /00 s / s 063(35) TYPE 063 FPV063E FPV063E FPV063E FPV063E FPV063E31 FPV063E3 FPV063E5 FPV063E FPV063E65 FPV063E5 FPV063E0 FPV063E5 FPV063E FPV063E170 FPV063E0 FPV063E0 FPV063E5 FPV063E0 FPV063E3 FPV063E0 FPV063E @1A 63@1A 6@1A 176@5A 317@5A 361@5A 75@5A 63@5A 66@5A Working DC AC / s 1A /00 s / s (32) TYPE 0 FPV0E FPV0E FPV0E FPV0E FPV0E31 FPV0E3 FPV0E5 FPV0E FPV0E65 FPV0E5 FPV0E0 FPV0E5 FPV0E FPV0E170 FPV0E0 FPV0E0 FPV0E5 FPV0E0 FPV0E3 FPV0E0 @ 63@ 6@ 176@A 317@A 361@A 75@A 63@A 66@A 13@A Remark: The working DC of 063 and 0 part number are identified as: V V V V

10 MV INTRODUCTION FO FPV SERIES MUTIAYER Multilayer Chip High Speed Series FPV ESD EFT The Multilayer High-Speed Series is a very low capacitance extension to the FPV family of Transient Suppressor available in 05,1 and surface mount chip. The High Speed series provides protection from ESD and EFT in high speed data-line and other high frequency applications. I/O Data, Diagnostic I/O Ports USB Universal Serial Bus (USB) Video & Audio Ports Portable/Hand-Held Products / Mobile Communications/Cellular Phones /DSP Computer/DSP Products Industrial Instruments Including Medical 05(02) TYPE 05 Working DC AC / s 1A /00 s / s FPV0505S3R3 FPV0505S5R6 M % FPV0505SR0 FPV0505SR0 FPV0505S1 FPV0505S1 FPV0505S1 FPV0505S1 FPV0505S (03) TYPE Working 1 DC AC / s 1A /00 s / s FPV10S3R3 M % 15 0 FPV10S5R6 1 FPV10SR FPV10SR FPV10S1 7. FPV10S FPV10S1 50 FPV10S1.3 5 FPV10S0 FPV10S FPV10S FPV10S2. 3 FPV10S FPV10S FPV10S

11 (005) TYPE Working DC AC / s 1A /00 s / s FPV1S3R3 FPV1S5R6 FPV1SR0 FPV1SR0 FPV1S1 FPV1S1 FPV1S1 FPV1S1 FPV1S0 FPV1S2 FPV1S2 FPV1S2 FPV1S0 M % I-V CURVES VICurves - 3.3V and V Products 50 VI Curves - V,V and V Products (V) 15 5 (V) (A) 3.3V, J 3.3V, >J V, J V, >J (A) V, J V, J V, J V, >J 0 VI Curves - V and V Products 0 VI Curves - V, V,and V Products 0 (V) (V) (A) V, J V, >J V, J V, >J (A) V, J V, J V, J V, >J

12 MV INTRODUCTION FO FPV SERIES MUTIAYER VS. TEMPERATURE Voltag as Percent of Average Breakdown Vdtage Temperature Dependence of (A) ENERGY AND CAPACITANCE VS. TEMPERATURE PERCENT OF RATED CAUE AMBIENT TEMPERATURE( ) REIABIITY TEST DATA Relative to + TYPICA CAPACITANCE VS TEMPERATURE Reference Average Temperature ( ) 2 Heat resistance (High-Temperature load) Test Sample:FPV0505G3R3 2 ow Temperature Resistance Test Sample:FPV10G5R5 (V) (V) Thermal Shock (Temperature cycle) Test Sample:FPV0505G5R6 2 1 Temal Shock Test - +5 at minute High Temperature life test: (ma) Vdc max applied at 5-1 (ma) 0 hour 00 hours cycle 0cycles (V) ow Temperature Resistance test at (ma) Resistamce to Solder Heat FPVG5R6, FPV32G5R6 Test Sample:FPV0505G5R6,FOV10G5R Resustance to solder heat Test - 2,sec Chip Size 0 hour hours 2 3

13 MUTIAYER CHIP VARISTOR ARRAY CVA 32 - G 3R3 P M T Product Code CVA Multilayer Chip Array ( W T) (mm) Dimensions Configuration 2 2 Array Array Product Series S G High speed type General type Working DC 3R V V Termination P Plated S Non-plated Tolerance M % Packaging Style T B Tape & Reel Bulk SHAPE AND DIMENSIONS & EQUIVAENT CIRCUIT unit mm(inch) Part No. (00) 32 () ( ) ( 0.00) W ( ) ( ) T 0.5 ( ) 0. ( ) E /- ( /-0.00) ( ) E ( ) 0.2 ( ) D ( ) 0. ( )

14 MV INTRODUCTION FO FPV SERIES MUTIAYER Multilayer Chip Array Electrical Characteristics Per Element Reduced component placement costs. PCB Downsize PCB. Use in multiple lines for transient suppression. Working DC AC / s 1A /00 s / s CVA-2G5R6 M % 1 5 CVA-2GR0 6. CVA-2G1 5 CVA-2G0 5 CVA-2S0 N/A <75 CVA32-G5R6 M % 1 5 CVA32-GR0 6. CVA32-G1 5 CVA32-G0 5 CVA32-S0 N/A <75

15 Ultra-low capacitance Chip Ultra-low capacitance varistors are FPV high-speed series, its lower capacity and faster response Data, Diagnostic I/O Ports Universal Serial Bus (USB) Video & Audio Ports Portable/Hand-held products Mobile commuications/cellular Phones computer/dsp Products Industrial Instruments Induding Medical CD Monitor PART NUMBER IDENTIFICATION FPV 10 S 3R3 P M T 070 Product Code ( W T) (mm) Dimensions Product Series Working DC Termination Tolerance Packaging Style FPV Multilayer Chip S High speed type 3R V V P S Plated Non-plated Pt/Pd/Ag M % T B Tape & Reel Bulk 070 7PF 15PF Working DC AC / s 1A /00 s / s FPV0505S3R3 M % ~1.5 FPV0505S5R6 M % ~1.5 FPV0505S0 M 0 1 % ~.3 FPV0505S0 M 070 % ~. FPV10S3R3 M % ~1.5 FPV10S5R6 M % ~1.5 FPV10S0 M 0 1 % ~.3 FPV10S0 M 070 % ~.

16 MV INTRODUCTION FO FPV SERIES MUTIAYER REIABIITY TESTING N0. Item Specified value Test methods 1 Operating temperature range -55to+5 2 Storage temperature range -to+ 0 ~ preheating temperature:0 ~ 3 Solderability At least 0% of terminal electrode is covered by new solder Preheating time:s : 2 Solder temperature: Duration:3S 1S 3~5 Flux: immersion into methanol solution with colophony for 3 to 5 secretary. Resistance to soldering No damage such as crucks should be caused in chip element At least 75% of terminal electrode is covered by new solder. change within. 0 ~ preheating temperature:0 ~ Preheating time:s : 2 Solder temperature: 2 1 Duration:S 1S 3~5 Flux: immersion into methanol solution with colophony for 3 to 5 secretary N N Applied force: 5N force for 05 and 1 series. N force for series. 5 Adhesion of electrode The termination and body should be no damage eep time 1S 6 Drop No mechanical damage. change within 5%. 1 Droppedtimesonaconcrete floorfromaheightof1m. 7 oading at low temperature No mechanical damage. change within 5%. - 2 Temperature:- 2 Duration: hrs

17 N0. Item Specified value Test methods 5 2 Temperature: Duration: 00 hrs oading at high temperature No mechanical damage. change within 5%. Applied : Working oading under Damp Heat No mechanical damage. change within 5%. 0~5% RH Humidity:0 to 5% RH 2 Temperature: 2 Duration: hrs Applied : Working (gf) Resistance to pressure of substrate The body shall not be damaged by forces applied on the right. d w Vibration No mechanical damage. change within 5%. ~55~Hz Frequency to 55 to Hz mm Amplitude:mm X Y Z Directions:2hrs each in X,Y,Z direction Temperature:- for 3min +0 for 3min Thermal shock No mechanical damage. change within 5%. Transforming interval:max sec 32 Number of cycles:32 Note: When there are questions concerning, measurement shall be made after recovery under the standard condition. 2hrs of

18 MV INTRODUCTION FO FPV SERIES MUTIAYER STANDAE QUANTITY TYPE Quantity (PCS) TAPING DRAWINGS TAPING DIMENSIONS (UNIT: mm) Paper carrier Sprocket Hole (+,0) Chip Cavity Direction of Feed Part NO. A B F T max max max

19 W P E F D D1 P 0 P 0 P2 A 0 B 0 t 2.0+/ / / /-0. 5+/- 0.0+/-0..0+/ / /-0..5+/ / /- +/ / / /-0..0+/ /-.+/-0..5+/-0. +/ / / / /-0. 5+/- 0.0+/-0..0+/ /- 2.0+/ / / / / / /-0. 5+/- 0.0+/-0..0+/ /- 1.0+/ / / / / / /-0. 5+/- 0.0+/-0..0+/ /- 2+/ / / Embossed Carrier / /-0. 5+/ / /-0. o REE DIMENSIONS (UNIT mm) CF- CF- A B C 1 1 N G CF

20 MV INTRODUCTION FO FPV SERIES MUTIAYER EADER AND BAN PORTION ~0.7N PEEING OFF FORCE : to 0.7N in the direction show below.

Introduction fo FPV Series Multilayer Chip Varistor

Introduction fo FPV Series Multilayer Chip Varistor Introduction fo FPV Series Multilayer Chip Multilayer Chip s (MLV) are Transient Voltage Suppressors (TVS) which manufactured from semiconducting ceramics by the highly advanced multilayer formation technologies,

More information

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four

More information

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLA Automotive Series MLA Automotive Varistor Series RoHS Description The MLA Automotive Series of transient voltage surge suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are

More information

Features. Continuous AUML Series Units. ) 1.5 to 25 J Jump Start Capability (5 minutes), (V JUMP. ) 48 V Operating Ambient Temperature Range (T A

Features. Continuous AUML Series Units. ) 1.5 to 25 J Jump Start Capability (5 minutes), (V JUMP. ) 48 V Operating Ambient Temperature Range (T A AUML Varistor Series RoHS Description The AUML Series of Multilayer Transient Surge Suppressors was specifically designed to suppress the destructive transient voltages found in an automobile. The most

More information

Surface Mount Multilayer Varistors

Surface Mount Multilayer Varistors ESD Protection (ES) Series Fast Response < 0.5 ns Low Working 5 V Low Capacitance Low Leakage Current < 1 μa Low Application Fields: Cell Phones Digital Cameras PDAs MP3 Notebooks Working (Max) (Max) Leakage

More information

AUML Varistor Series. Surface Mount Varistors

AUML Varistor Series. Surface Mount Varistors The AUML Series of Multilayer Transient Surge Suppressors was specifically designed to suppress the destructive transient voltages found in an automobile. The most common transient condition results from

More information

Metal Oxide Varistor:TVM-B Series

Metal Oxide Varistor:TVM-B Series Features 1. RoHS compliant 2. High surge suppress capability 3. EIA size 0402 ~ 2220 4. Operating voltage: 5.5 ~ 85 Vdc 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer ceramic construction

More information

ZV/ZVY Series Low Voltage SMD Varistors

ZV/ZVY Series Low Voltage SMD Varistors Description: The ZV Series of low voltage varistors is designed to protect sensitive electronics devices against high voltage surges in the low voltage region. They offer excellent transient energy absorption

More information

ORDER INFORMATION L-KLS6-MVR G

ORDER INFORMATION L-KLS6-MVR G istors Varistor s L-KLS6-MVR3220-431G 3220 Varistor s,430v,39pf 1 Electrical Characteristics 1.1 Technical Data Symbol Value Unit Maximum allowable continuous AC voltage*1 V RMS 275.0 V Maximum allowable

More information

MVR G. Size: Unit:mm. Type Length(L) Width(W) High(H) Termination(L1) ± ± (max) 0.40±

MVR G. Size: Unit:mm. Type Length(L) Width(W) High(H) Termination(L1) ± ± (max) 0.40± 1 Electrical Characteristics 1.1 Technical Data Symbol Value Unit Maximum allowable continuous AC voltage*1 V RMS 50.0 V Maximum allowable continuous DC voltage V DC 65.0 V Varistor voltage Measured*2

More information

MULTILAYER CHIP VARISTORS

MULTILAYER CHIP VARISTORS Feature Varistor Voltage from5v to 100V Fast response time Low leakage current High surge current ability Bidirectional clamping, high energy Wide Operating temperature range from -55-125 Suitable for

More information

S J

S J 1. Part Number Identification SPECIFICATION Brightek (Europe) Limited S01-2220 - 240 250 J Series Name Inner Code Size 1206~3220 250 250 = 25 10 0 V=25J 1R5 1R5 = 1.5J Breakdown Voltage 240 = 24 10 0 V=24V

More information

MLE Varistor Series. Features. Size Metric EIA Applications.

MLE Varistor Series. Features. Size Metric EIA Applications. The MLE Series family of Transient Voltage Suppression devices are based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress ESD events, including those specified

More information

SPHV-C Series 200W Discrete Bidirectional TVS Diode

SPHV-C Series 200W Discrete Bidirectional TVS Diode SPHV-C Series W Discrete Bidirectional TVS Diode RoHS Pb GREEN Description The SPHV-C series is designed to replace multilayer varistors (MLVs) in portable applications, LED lighting modules, and low speed

More information

AQxxC Series 450W Discrete Bidirectional TVS Diode

AQxxC Series 450W Discrete Bidirectional TVS Diode AQxxC Series 5W Discrete Bidirectional TVS Diode RoHS Pb GREEN Description The bidirectional AQxxC series is designed to replace multilayer varistors (MLVs) in electronic equipment for low speed and DC

More information

SFI Electronics Technology

SFI Electronics Technology 1. Part Number Identification SFI 2220 SA 240 250 J Company Logo Inner Code Size 1206~3220 SA SHA Series 250 250 = 25 10 0 V=25J 1R5 1R5 = 1.5J Breakdown Voltage 240 = 24 10 0 V=24V 151 = 15 10 1 V=150V

More information

Pan Overseas Zinc Oxide Varistors

Pan Overseas Zinc Oxide Varistors PVR - ZINC OXIDE VARISTORS Introduction Zinc Oxide Varistor is a non-linear resistance device, whose voltage and current relationship vary according to the Law of Powers. When high transients or surges

More information

varistor plus catalog

varistor plus catalog varistor plus catalog Single Layer Varistor Technology Surface Mount & Leaded Products SEI electronics inc. P.O.Box 58789 Raleigh,NC 27658-8789 Tel. 1-888-sei-sei-sei Fax. 919-850-9504 www.seielect.com

More information

Glass Encapsulated SMD Varistor MLV

Glass Encapsulated SMD Varistor MLV (VJ12, 2, 13, 14, 15, 32) Transient Voltage Suppression, ESD Protection Devices & EMI Devices GENERAL DESCRIPTION AVX s Professional Multilayer Varistors include 3 series of glass coated products as listed

More information

JNR ZINC OXIDE VARISTORS FEATURES APPLICATIONS PARAMENTERS DEFINITION HOW TO ORDER

JNR ZINC OXIDE VARISTORS FEATURES APPLICATIONS PARAMENTERS DEFINITION HOW TO ORDER JNR ZINC OXIDE VARISTORS Zinc oxide varistor is a voltage dependent resistor with symmetrical voltage -current characteristics that is designed to protect all kinds of electronic devices or elements from

More information

E CQC CQC CQC CQC CQC D-Seires. 11 to to to

E CQC CQC CQC CQC CQC D-Seires. 11 to to to Description CNR D/V/P/H/N series metal oxide varistor are nonlinear resistors, consisting main of zinc oxide and several kinds of metal oxide additive.they are bilateral and symmetrical V-I characteristics

More information

AQHV Series 200W Discrete Unidirectional TVS Diode

AQHV Series 200W Discrete Unidirectional TVS Diode AQHV Series W Discrete Unidirectional TVS Diode RoHS Pb GREEN Description The AQHV series is designed to provide an option for very fast acting, high performance over-voltage protection devices. Ideally

More information

0.15 +/ (0.006" +/ ) / (0.033" +/ ) / (0.088" +/ ") 1.91 (0.075") 1.09 (0.043") 0.91 (0.

0.15 +/ (0.006 +/ ) / (0.033 +/ ) / (0.088 +/ ) 1.91 (0.075) 1.09 (0.043) 0.91 (0. Note: For wave solder, increase the spacing in both the horizontal Surface Mount Polymeric.66 and Electrostatic +/- vertical.6 dimensions by Discharge Suppressors.54 (.") where denoted by an asterisk (*).4

More information

Product Specification

Product Specification Product Name : AEM Part Number : ES0402V014CT Customer : Customer Revision: 2 Date: 2011-09-08 AEM Components (Suzhou) Co., Ltd 458 Shenhu Road, Suzhou Industrial Park Jiangsu, P.R China, 215122 TEL: 86-512-6258-0028

More information

P-Series 11 to to to to to to to 1100 >1000 <25

P-Series 11 to to to to to to to 1100 >1000 <25 Description CNR D/V/P/H series metal oxide varistor are nonlinear resistors, consisting main of zinc oxide and several kinds of metal oxide additive.they are bilateral and symmetrical V-I characteristics

More information

TABLE of contents. Metal Oxide Varistor (MOV) Varistors-5D Series Varistors-7D Series Varistors-10D Series... 5

TABLE of contents. Metal Oxide Varistor (MOV) Varistors-5D Series Varistors-7D Series Varistors-10D Series... 5 TABLE of contents Subject Page Metal Oxide Varistor (MOV)..................................................... 1 Varistors-5D Series............................................................ 3 Varistors-7D

More information

Multi-Layer Power Inductors (IP Series)

Multi-Layer Power Inductors (IP Series) Multi-Layer Power Inductors (IP Series) For DC/DC Converter Application ORDERING CODE IP R M P S 9 PRODUCT CODE IP : Multilayer Power Inductor (Lead Free) DIMENSION (L X W) Code Dimension EIA. x. mm. X.

More information

SM24CANB Series 500W TVS Diode Array

SM24CANB Series 500W TVS Diode Array SM4CANB Series 5W TVS Diode Array RoHS Pb GREEN Description The SM4CANB TVS Diode Array is designed to protect automotive Controller Area Network (CAN lines from damage due to electrostatic discharge (ESD,

More information

Metal Oxide Varistor (MOV) Data Sheet

Metal Oxide Varistor (MOV) Data Sheet Metal Oxide Varistor (MOV) Data Sheet Features Wide operating voltage (V 1mA ) range from 18V to 1800V Fast responding to transient over-voltage Large absorbing transient energy capability Low clamping

More information

1SMA10CAT3G Series, SZ1SMA10CAT3G Series. 400 Watt Peak Power Zener Transient Voltage Suppressors. Bidirectional

1SMA10CAT3G Series, SZ1SMA10CAT3G Series. 400 Watt Peak Power Zener Transient Voltage Suppressors. Bidirectional 110CAT3G Series, SZ110CAT3G Series 400 Watt Peak Power Zener Transient Voltage Suppressors Bidirectional The series is designed to protect voltage sensitive components from high voltage, high energy transients.

More information

VZCA2.E VZCA8.E CQC CQC CQC CQC CQC D-Seires. 11 to to 1465.

VZCA2.E VZCA8.E CQC CQC CQC CQC CQC D-Seires. 11 to to 1465. Description CNR D/V/P/H series metal oxide varistor are nonlinear resistors, consisting main of zinc oxide and several kinds of metal oxide additive.they are bilateral and symmetrical V-I characteristics

More information

Anti-Surge Thick Film Chip Resistors

Anti-Surge Thick Film Chip Resistors FEATURES EXCELLENT ANTI-SURGE & ANTI-SULFUR CHARACTERISTICS AEC-Q200 QUALIFIED RATED POWER UPGRADE IN SMALLER PACKAGE SIZE AVAILABLE IN ± TOLERANCE BOTH FLOW SOLDER AND REFLOW SOLDERING ARE APPLICABLE

More information

WLFI1608 Ferrite Chip Inductors

WLFI1608 Ferrite Chip Inductors WLFI1608 Ferrite Chip Inductors *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_ WLFI1608 Series_V1.0 July. 2015 FEATURES 1. General purpose chip ferrite power inductor

More information

RELIABILITY TEST P10 PRODUCT SERIES P11 ~ P16 P17 ~ P22 P23 P24 P25 P26 V-I CURVE P27 ~ P31 SURGE LIFE TIME RATINGS P32 ~ P36 OUTLINE DIMENSION

RELIABILITY TEST P10 PRODUCT SERIES P11 ~ P16 P17 ~ P22 P23 P24 P25 P26 V-I CURVE P27 ~ P31 SURGE LIFE TIME RATINGS P32 ~ P36 OUTLINE DIMENSION Page 1 INDEX P1 VARISTOR OVERVIEW P2 INFORMATION REQUEST FORM P3 FEATURES P4 VARISTOR V-I CHARACTERISTICS P5 HOW TO SELECT A VARISTOR P6 NOTICE FOR APPLICATION P7 ~ P8 TERMINOLOGY & GENERAL P9 CHARACTERISTICS

More information

Anti-Surge Thick Film Chip Resistors

Anti-Surge Thick Film Chip Resistors FEATURES EXCELLENT ANTI-SURGE CHARACTERISTICS AEC-Q200 QUALIFIED RATED POWER UPGRADE IN SMALLER PACKAGE SIZE MEETS +85 C/85%RH TEST 000 HOURS MEETS CLIMATE CATEGORY (IEC 60068): 55/55/56 AVAILABLE IN ±

More information

Data sheet SMD Wire Wound Chip Inductor WL Series

Data sheet SMD Wire Wound Chip Inductor WL Series Data sheet SMD Wire Wound Chip Inductor W Series Scope -Ceramic body and wire wound construction provide highest s available.. Features -Ceramic base provide high -Ultra-compact inductors provide high

More information

Spezifikation für Freigabe / specification for release

Spezifikation für Freigabe / specification for release Datum / Date : 2007-01-24 ROHS Compliant A Mechanische Abmessungen / dimensions : SIZE SISE W L T a 402 0.5 1.0 0.6 0.25 603 0.8 1.6 0.9 0.3 805 1.25 2.0 1.2 0.3 1206 1.6 3.2 1.5 0.5 1210 2.5 3.2 1.5 0.5

More information

SR20X, SR25X ±1%, ±5% Power chip resistors Size 2010, 2512

SR20X, SR25X ±1%, ±5% Power chip resistors Size 2010, 2512 SR20X, SR25X ±1%, ±5% Power chip resistors Size 2010, 2512 ( Automotive & Anti-sulfuration ) Page 1 of 7 SR20-25X_V04 Sep.-2011 FEATURE 1. High reliability and stability ±1% 2. Sulfuration resistant 1000ppm

More information

Wire Wound Chip Inductor-WB Series

Wire Wound Chip Inductor-WB Series Wire Wound Chip Inductor-WB Series Construction 4 1 3 1 Ceramic Core 3 Electrode (Ag/Pd+Ni+Sn) 2 Magnet Wire 4 UV Glue 2 Features -Ceramic base provide high -Ultra-compact inductors provide high Q factors

More information

WLFI2012 Ferrite Chip Inductors

WLFI2012 Ferrite Chip Inductors WLFI2012 Ferrite Chip Inductors *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_ WLFI2012 Series_V1.0 July. 2015 FEATURES 1. General purpose chip ferrite power inductor

More information

Power Inductors (IP Series)

Power Inductors (IP Series) Multi-Layer Power Inductors (IP Series) ORDERING CODE... 1 Standard External Dimensions... 2 Power Inductor for Choke (L Type)... 3 Power Inductor for DC/DC converter (S Type)... 4 Testing Condition &

More information

THIS PAGE WAS INTENTIONALLY LEFT BLANK.

THIS PAGE WAS INTENTIONALLY LEFT BLANK. THIS PAGE WAS INTENTIONALLY LEFT BLANK. Table of Contents Transient Suppression Diodes............................................................ 1 General Information...........................................................................

More information

Maida Multilayer Varistors

Maida Multilayer Varistors Multilayer Varistors ESD and Suppression in sizes from 0402 to 2220 Multilayer Varistors (MLVs) are leadless surface mount chips available in a wide range of size, voltage and capacitance values for use

More information

Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & ANTI-SULFURATION. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free

Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & ANTI-SULFURATION. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free No.: RMNW K HTS-1 /3 Date: 217. 4. 21 Data sheet : ANTI-SULFURATION RMNW1,16,2,32,35 AEC-Q2 qualified RoHS COMPLIANCE ITEM Halogen and Antimony Free Note: Stock conditions Temperature: +5 C +35 C Relative

More information

Spezifikation für Freigabe / specification for release

Spezifikation für Freigabe / specification for release Artikelnummer / part number : 82550200 Datum / Date : 31.07.06 description : 0805 SMD VARISTOR Lead Free SMD size: 0805 ROHS Compliant A Mechanische Abmessungen / dimensions : SIZE SIZE W L T a 0402 0.5

More information

SM Series 400W TVS Diode Array

SM Series 400W TVS Diode Array General Purpose ESD Protection - SM5 through SM3 SM Series W TVS Diode Array RoHS Pb GREEN Description The SM series TVS Diode Array is designed to protect sensitive equipment from damage due to electrostatic

More information

METAL OXIDE VARISTOR (MOV)

METAL OXIDE VARISTOR (MOV) METAL OXIDE VARISTOR (MOV) How to Order SR 241 K 10 D S 40 X Type code Tolerance Disk Size Code Disk Type Lead Type or Taping Code Lead Cutting Special Request SR: Walsin ( volt) (From 180 to 112) Two

More information

Specification Status: Released

Specification Status: Released PAGE NO.: 1 of 9 Specification Status: Released BENEFITS ESD protection for high frequency applications (HDMI 1.3) Smaller form factor for board space savings Helps protect electronic circuits against

More information

Specification Status: Released

Specification Status: Released PAGE NO.: 1 OF 9 Specification Status: Released BENEFITS ESD protection for high frequency applications (HDMI 1.3) Smaller form factor for board space savings Helps protect electronic circuits against

More information

Content (RF Inductors) Multi-Layer High Frequency Inductors (IQ & HI Series) Cautions... 18

Content (RF Inductors) Multi-Layer High Frequency Inductors (IQ & HI Series) Cautions... 18 Content (RF Inductors) Multi-Layer High Inductors (IQ & HI Series)... 2 Ordering Code... 2 Standard External Dimensions... 3 High Q Type (IQ Series)... 4 Standard Type (HI Series)... 5 Testing Condition

More information

ÒZNRâÓ Transient/Surge Absorbers, SMD Moded Case Type

ÒZNRâÓ Transient/Surge Absorbers, SMD Moded Case Type ÒZNRâÓ Transient/Surge Absorbers, SMD Moded Case Type Type: VF Type: CF Type: SF n Features l Large withstanding surge current capability, compact size l Designed for flow/reflow soldering l Excellent

More information

YAGEO CORPORATION Lead-Free & RoHs Compliance!!

YAGEO CORPORATION Lead-Free & RoHs Compliance!! Lead-Free & RoHs Compliance!! SPECIFICATION FOR APPROVAL CUSTOMER: CUSTOMER P/N: OUR DWG No: QUANTITY: Pcs. DATE: ITEM: PBY321611T-SERIES-N SPECIFICATION ACCEPTED BY: COMPONENT ENGINEER ELECTRICAL ENGINEER

More information

WK25S WK20S WK10S WK12S WK08S WK06S. Thick Film Power Surge Chip Resistors. Size 2512, 2010, 1210, 1206, 0805, 0603

WK25S WK20S WK10S WK12S WK08S WK06S. Thick Film Power Surge Chip Resistors. Size 2512, 2010, 1210, 1206, 0805, 0603 WK25S WK20S WK10S WK12S WK08S WK06S ±5% 5%, ±10 10%, ±20 20% Thick Film Power Surge Chip Resistors Size 2512, 2010, 1210, 1206, 0805, 0603 *Contents in this sheet are subject to change without prior notice.

More information

THIS PAGE WAS INTENTIONALLY LEFT BLANK.

THIS PAGE WAS INTENTIONALLY LEFT BLANK. THIS PAGE WAS INTENTIONALLY LEFT BLANK. Table of Contents Transient Suppression Diodes... 1 General Information... 2 P4KE Series 400 Watt... 8 SA Series 500 Watt... 12 P6KE Series 600 Watt... 18 1.5KE

More information

LBZX84XXXXLT1G SEMICONDUCTOR. 225 mw SOT-23 Zener Voltage Regulator Diodes. Zener Voltage Regulator Diodes. SERIES 225mW SOT-23 TECHNICAL DATA

LBZX84XXXXLT1G SEMICONDUCTOR. 225 mw SOT-23 Zener Voltage Regulator Diodes. Zener Voltage Regulator Diodes. SERIES 225mW SOT-23 TECHNICAL DATA SEMICONDUCTOR TECHNICAL DATA 225 mw SOT-23 Zener Voltage Regulator Diodes GENERAL DATA APPLICABLE TO ALL SERIES IN THIS GROUP Zener Voltage Regulator Diodes LBZX84XXXXLTG SERIES 225mW SOT-23 3 Cathode

More information

Metal Oxide Varistor:TVR Series

Metal Oxide Varistor:TVR Series Features. Body size: Ф5 ~ Ф20mm 2. Wide operating voltage range:vac ~ 00Vac 3. Operating temperature range:-40 ~ +85 C 4. Agency recognition: UL 449 3 rd /UL 44/cUL/VDE /CSA/CQC 5. TVR48~42 and TVR208~202

More information

General Purpose Ceramic Capacitors (C Series)

General Purpose Ceramic Capacitors (C Series) Features: RoHS Compliant and Halogen Free Capacitance range: 0.1pF to 220uF range: 4V to 100V Terminations: 100% matte Tin (Sn), Palladium (Pd-Ag), Gold (Au) and Lead (Pb) Very low ESR in X7R/X5R (

More information

SPECIFICATION FOR APPROVAL

SPECIFICATION FOR APPROVAL SPECIFICATION FOR APPROVAL CUSTOMER CUSTOMER P/N OUR DWG No Lead-Free & RoHs Compliance!! QUANTITY Pcs. DATE 2010/11/01 ITEM SBK160808T-121Y-N COMPONENT ENGINEER ELECTRICAL ENGINEER MECHANICAL ENGINEER

More information

WK25S WK20S WK10S WK12S WK08S WK06S. Thick Film Power Surge Chip Resistors AEC Q-200 Qualified Size 2512, 2010, 1210, 1206, 0805, 0603

WK25S WK20S WK10S WK12S WK08S WK06S. Thick Film Power Surge Chip Resistors AEC Q-200 Qualified Size 2512, 2010, 1210, 1206, 0805, 0603 WK25S WK20S WK10S WK12S WK08S WK06S ±5% 5%, ±10 10%, ±20 20% Thick Film Power Surge Chip Resistors AEC Q-200 Qualified Size 2512, 2010, 1210, 1206, 0805, 0603 *Contents in this sheet are subject to change

More information

TVS Diode Arrays (SPA Diodes) SP2502L Series 3.3V 75A Diode Array. Lightning Surge Protection - SP2502L Series. RoHS Pb GREEN.

TVS Diode Arrays (SPA Diodes) SP2502L Series 3.3V 75A Diode Array. Lightning Surge Protection - SP2502L Series. RoHS Pb GREEN. SP202L Series 3.3V 7A Diode Array RoHS Pb GREEN Description The SP202L provides overvoltage protection for applications such as 0/00/000 Base-T Ethernet and T3/ E3 interfaces. This device has a low capacitance

More information

SMD Wire Wound Chip Inductor

SMD Wire Wound Chip Inductor GSW Series SMD Wire Wound Chip Inductor Scope -Ceramic body and wire wound construction provide highest s available.. Features -Ceramic base provide high -Ultra-compact inductors provide high Q factors

More information

WW25X, WW18X, WW12X, WW08X, WW06X ±1%, ±5% Thick Film Current Sensing Chip Resistors Size 2512, 1218, 1206, 0805, 0603 (Automotive)

WW25X, WW18X, WW12X, WW08X, WW06X ±1%, ±5% Thick Film Current Sensing Chip Resistors Size 2512, 1218, 1206, 0805, 0603 (Automotive) WW25X, WW18X, WW12X, WW08X, WW06X ±1%, ±5% Thick Film Current Sensing Chip Resistors Size 2512, 1218, 1206, 0805, 0603 (Automotive) *Contents in this sheet are subject to change without prior notice. Page

More information

MA04X, MA06X ±1%, ±5%, Convex Type General purpose chip resistors array

MA04X, MA06X ±1%, ±5%, Convex Type General purpose chip resistors array MA04X, MA06X ±1%, ±5%, Convex Type General purpose chip resistors array Size 0402x4, 0603x4 (8p4R) ( Automotive & Anti-sulfur ) Page 1 of 8 MA04/ 06_V03 Apr.2010 FEATURE 1. High reliability and stability

More information

Metal Oxide Varistor:TVT Type

Metal Oxide Varistor:TVT Type Features. RoHS compliant 2. 2 leaded or 3 leaded thermally protected metal oxide varistor, Three-leaded version available for indication purposes. 3. Body size : 4, 20, 22, 25, 32 and 34 mm in diameter

More information

WA04X, WA06X ±1%, ±5%, Convex Type General purpose chip resistors array

WA04X, WA06X ±1%, ±5%, Convex Type General purpose chip resistors array WA04X, WA06X ±1%, ±5%, Convex Type General purpose chip resistors array Size 0402x4, 0603x4 (8p4R) (Automotive ) Page 1 of 8 ASC_WAxxX_J_V05 May.2011 FEATURE 1. Small size and light weight 2. Reduced size

More information

THIS PAGE WAS INTENTIONALLY LEFT BLANK.

THIS PAGE WAS INTENTIONALLY LEFT BLANK. THIS PAGE WAS INTENTIONALLY LEFT BLANK. Table of Contents Features... 2 Applications... 2 Approvals... 2 Part Marking... 3 System... 4 Absolute Ratings... 4 Fuse Configuration and Dimensions... 5 Specifications...

More information

Multilayer Chip Beads / CP TYPE(Large Current)

Multilayer Chip Beads / CP TYPE(Large Current) Multilayer Chip Beads / CP TYPE(Large Current).Features: 1.Closed magnetic circuit structure allows high density mounting while preventing crosstalk. 2.Extremely high reliability due to entirely monolithic

More information

WW25N ±1%, ±5%, 2W Ultra low ohm power chip resistors Size 2512 (6432)

WW25N ±1%, ±5%, 2W Ultra low ohm power chip resistors Size 2512 (6432) WW25N ±1%, ±5%, 2W Ultra low ohm power chip resistors Size 2512 (6432) Metal Current Sensing Type *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_WW25N_V14 Jul - 2015

More information

DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R

DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R Product Specification May 31, 2016 V.14 DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product

More information

NXE1 Series Isolated 1W Single Output SM DC/DC Converters

NXE1 Series Isolated 1W Single Output SM DC/DC Converters NXE1 Series SELECTION GUIDE FEATURES Patents pending Lower Profile UL695 Recognition pending ANSI/AAMI ES661-1 Recognition pending 3kVDC Isolation Hi Pot Test Substrate Embedded Transformer Automated Manufacture

More information

DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R

DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R Product Specification October 27, 16 V.15 DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free

More information

Notice for TAIYO YUDEN Products

Notice for TAIYO YUDEN Products Notice for TAIYO YUDEN Products [ For General Electronic Equipment (General Environment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is

More information

Multi-Layer Power Inductors (IP_L Series)

Multi-Layer Power Inductors (IP_L Series) Multi-Layer Power Inductors (IP_L Series) For Choke Application ORDERING CODE IP 2012 2R2 M P L 9 PRODUCT CODE IP : Multilayer Power Inductor (Lead Free) DIMENSION (L X W) Code Dimension EIA 1608 1.6 x

More information

Nov 7, 2006 DIELECTRIC CERAMIC FILTER SPECIFICATION 1 OF 9 SPECIFICATION ITEM: DIELECTRIC CERAMIC FILTER PART NUMBER: CF

Nov 7, 2006 DIELECTRIC CERAMIC FILTER SPECIFICATION 1 OF 9 SPECIFICATION ITEM: DIELECTRIC CERAMIC FILTER PART NUMBER: CF Nov 7, 2006 DIELECTRIC CERAMIC FILTER SPECIFICATION 1 OF 9 SPECIFICATION ITEM: DIELECTRIC CERAMIC FILTER PART NUMBER: CF-19100328 4/14/06 Added recommended PCB layout and plots. 6/2/06 Added Tape and Reel

More information

POWERBOX Industrial Line PMF20W Series 20W 4:1 Single Output DC/DC Converter Manual. DC/DC Converter Features. Introduction

POWERBOX Industrial Line PMF20W Series 20W 4:1 Single Output DC/DC Converter Manual. DC/DC Converter Features. Introduction Table of Contents Output specification Input specification General specification Environmental specifications EMC characteristic curves Output voltage adjustment Input source impedance Output over current

More information

WF25S WF20S WF12S ±5% 20% Power Surge Chip Resistors Size 2512, 2010, Customer : Approval No : Issue Date : Customer Approval :

WF25S WF20S WF12S ±5% 20% Power Surge Chip Resistors Size 2512, 2010, Customer : Approval No : Issue Date : Customer Approval : WF25S WF20S WF12S ±5% 5%, ±10 10%, ±20 20% Power Surge Chip Resistors Size 2512, 2010, 1206 Customer : Approval No : Issue Date : Customer Approval : Page 1 of 7 WF25S WF20S WF12S Ver.4 Sep.-2008 FEATURE

More information

WK25S WK20S WK10S WK12S WK08S. Thick Film Power Surge Chip Resistors. Size 2512, 2010, 1210, 1206, 0805

WK25S WK20S WK10S WK12S WK08S. Thick Film Power Surge Chip Resistors. Size 2512, 2010, 1210, 1206, 0805 WK25S WK20S WK10S WK12S WK08S ±5%, ±10%, ±20% Thick Film Power Surge Chip Resistors Size 2512, 2010, 1210, 1206, 0805 *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_WKxxS_V02

More information

Metal Oxide Varistor:TVR-D Series

Metal Oxide Varistor:TVR-D Series Features. RoHS compliant 2. Halogen-free series are available 3. Body size: Ф7mm ~ Ф 20mm 4. Wide operating voltage range: 5Vac ~ 680Vac 5. High surge current rating up to 3KA 6. High energy rating up

More information

NXE1 Series Isolated 1W Single Output SM DC-DC Converters

NXE1 Series Isolated 1W Single Output SM DC-DC Converters NXE1 Series SELECTION GUIDE Order Code 1 Nominal Input Voltage Output Voltage Input Current Output Current Load Regulation (Typ) Load Regulation (Max) Output Ripple & Noise (Typ) Output Ripple & Noise

More information

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input reflected ripple current. Switching frequency NXE1S0305MC 85

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input reflected ripple current. Switching frequency NXE1S0305MC 85 SELECTION GUIDE Order Code 1 Nominal Input Voltage Output Voltage Input Current Output Current Load Regulation (Typ) Load Regulation (Max) Output Ripple & Noise (Typ) Output Ripple & Noise (Max) Efficiency

More information

SPECIFICATION SHEET. ±1%, ±5%, Convex Type General purpose chip resistors array

SPECIFICATION SHEET. ±1%, ±5%, Convex Type General purpose chip resistors array SPECIFICATION SHEET CNA24, CNA34 ±1%, ±5%, Convex Type General purpose chip resistors array Size 0402x4, 0603x4 (8p4R) ( Automotive & Anti-sulfur ) All data in this sheet are subject to change, modify

More information

DPX15-xxWDxx Dual Output: DC-DC Converter Module 9.5 ~ 36VDC, 18 ~ 75VDC input; ±5 to ±15 VDC Dual Output; 15 Watts Output Power

DPX15-xxWDxx Dual Output: DC-DC Converter Module 9.5 ~ 36VDC, 18 ~ 75VDC input; ±5 to ±15 VDC Dual Output; 15 Watts Output Power DPX15-xxWDxx Dual Output: DC-DC Converter Module 9.5 ~ 36VDC, 18 ~ 75VDC input; ±5 to ±15 VDC Dual Output; 15 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW

More information

WR18X(W), WR20X(W), WR25X(W) ±1%, ±5% Power chip resistors Size 1218,2010,2512

WR18X(W), WR20X(W), WR25X(W) ±1%, ±5% Power chip resistors Size 1218,2010,2512 WR18X(W), WR20X(W), WR25X(W) ±1%, ±5% Power chip resistors Size 1218,2010,2512 Customer : Approval No : Issue Date : Customer Approval : Page 1 of 7 WR18-20-25X(W) Ver.13 Oct.-2010 FEATURE 1. High power

More information

DPX30-xxSxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; 3.3 to 28 VDC Single Output; 30 Watts Output Power

DPX30-xxSxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; 3.3 to 28 VDC Single Output; 30 Watts Output Power DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; 3.3 to 28 VDC Single Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS

More information

DPX30-xxDxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power

DPX30-xxDxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS

More information

Ceramic transient voltage suppressors, CTVS

Ceramic transient voltage suppressors, CTVS Ceramic transient voltage suppressors, CTVS Reliability Date: April 2017 EPCOS AG 2017. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained

More information

Metal Oxide Varistor:TVR-D Series

Metal Oxide Varistor:TVR-D Series Features. RoHS compliant 2. Halogen-free series are available 3. Body size: Ф7mm ~ Ф 20mm 4. Wide operating voltage range: 5Vac ~ 680Vac 5. High surge current rating up to 3KA 6. High energy rating up

More information

DPX30-xxWDxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power

DPX30-xxWDxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS FOR INPUT AND

More information

Notice for TAIYO YUDEN Products

Notice for TAIYO YUDEN Products Notice for TAIYO YUDEN Products [ For General Electronic Equipment (General Environment) ] Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is

More information

Load (2) Single or Dual

Load (2) Single or Dual Features Regulated Converter Reinforced insulation for 25VAC working voltage Clearance and creepage distance >8.mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout

More information

Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration )

Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration ) SR12, SR10, SR08, SR06, SR04, General purpose chip resistors Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration ) *Contents in this sheet are subject to change without prior notice. Page 1 of 9 ASC_SR_V03

More information

SIDACtor Protection Thyristors Baseband Protection (Voice-DS1)

SIDACtor Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor Series - DO-214 Description SIDACtor Series DO-214AA are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides

More information

WW25M 1%, 5% Metal Plate Low Ohm Power Chip Resistors. Size 2512 (6432) 1W Current Sensing Type RoHS Exemption free and Halogen free

WW25M 1%, 5% Metal Plate Low Ohm Power Chip Resistors. Size 2512 (6432) 1W Current Sensing Type RoHS Exemption free and Halogen free WW25M 1%, 5% Metal Plate Low Ohm Power Chip Resistors Size 2512 (6432) 1W Current Sensing Type RoHS Exemption free and Halogen free *Contents in this sheet are subject to change without prior notice. Page

More information

DPX30-xxWSxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; 3.3 to 28VDC Single Output 30 Watts Output Power

DPX30-xxWSxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; 3.3 to 28VDC Single Output 30 Watts Output Power DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; 3.3 to 28VDC Single Output 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS FOR INPUT AND OUTPUT

More information

Molded Chip Wirewound Inductors

Molded Chip Wirewound Inductors FEATURES EIA SIZES A (1210), B (1812), C (1008) AND D (0805) EXCELLENT HIGH Q AND HIGH CHARACTERISTICS BOTH FLOW AND REFLOW SOLDERING APPLICABLE HIGH INDUCTANCE AVAILABLE IN SMALL SIZE EMBOSSED PLASTIC

More information

According to IEC , grade 1.1

According to IEC , grade 1.1 Single metallized film pulse capacitor, polypropylene dielectric According to IEC 60384-16, grade 1.1 TYPICAL APPLICATIONS Pulse operation in SMPS, TV, monitor, electrical ballast and other high frequency

More information

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input Current. Input reflected ripple current

SELECTION GUIDE. Nominal Input Voltage. Output Voltage. Input Current. Input reflected ripple current SELECTION GUIDE FEATURES Patents pending Lower Profile UL9 Recognition pending ANSI/AAMI ES1-1 Recognition pending 3kVDC Isolation Hi Pot Test Substrate Embedded Transformer Automated Manufacture Industry

More information

NTC Thermistor for Automotive: TSM-C Series

NTC Thermistor for Automotive: TSM-C Series Features 1. Qualification based on AEC-Q200 Rev-C 2. Operating temperature range: -50 ~ +150 3. Superior stability in high-temperature and high-humidity environment 4. RoHS & Halogen Free (HF) compliant

More information

TeleLink SM Fuse. CSA Approved File No. LR UL Recognized E Patent Pending. TeleLink SM Fuse. Product Description.

TeleLink SM Fuse. CSA Approved File No. LR UL Recognized E Patent Pending. TeleLink SM Fuse. Product Description. Product Description The TeleLink Surface Mount (SM) surge resistant time lag fuse has been designed to offer the ultimate in circuit protection while meeting the necessary surge requirements of the telecommunications

More information

PHE426 Single metallized film pulse capacitor, polypropylene dielectric According to IEC , grade 1.1

PHE426 Single metallized film pulse capacitor, polypropylene dielectric According to IEC , grade 1.1 Single metallized film pulse capacitor, polypropylene dielectric According to IEC 60384-16, grade 1.1 TYPICAL APPLICATIONS CONSTRUCTION L B Pulse operation in SMPS, TV, monitor, electrical ballast and

More information