FWT-200 OPTI-CHROMIC READER SYSTEM

Transcription

1 FWT-200 OPTI-CHROMIC READER SYSTEM User s Manual Covers Installation and Windows software for ISA and PCI cards September, 2002 Far West Technology, Inc. 330 South Kellogg Ave. Suite D Goleta, CA USA

2 INTRODUCTION The FWT-200 Opti-Chromic Reader is a computer controlled densitometer designed to read FWT-70 Opti- Chromic Detectors. The complete reader system consists of a computer (IBM PC\XT\AT compatible), the reader head, an ADC card for the computer (ISA and PCI versions available), a cable to connect the head to the card, and software. HARDWARE INSTALLATION Dedicated Computer We recommend that you use a dedicated computer for the Model 200. We have found that users who network, run multiple programs, or use inexpensive computers often have poor results with the Model 200. If you do have problems, stop multitasking, shut down all concurrent programs, remove the network connection, remove excess hardware and/or try a better quality computer. ADC Board (ISA Version) Before installing the ADC board in the computer you need to note the base address of the board. If you have other expansion cards in the computer you should also check that the base address does not conflict with the address of the other cards. If necessary, the base address may be altered by changing the DIP switch on the ADC card. To determine the base address of the card examine the DIP switch settings and the numbers printed on the printed circuit board (not the numbers on the DIP switch housing). The card is originally set up with an address of 0x300, which has switches 3 and 4 off and switches 5-9 on. The base address of the ADC card may be changed to provide a range of selections to the user. Table 1 gives the decimal and hexadecimal values and the position of each switch. Note the base address of the card so that this may be specified in the configuration file (DOS software version 1.x) or in the setup dialog box (version 2.x). The windows version allows you to specify the base address by showing how the DIP switches are set. Consult your computer manual for details on installing an expansion card in your computer. Most installations are as follows: First make sure that the computer is turned off and unplugged. Next open the case to allow access to the expansion slots. Choose an appropriate empty slot for the card. Remove the retaining bracket, being careful not to drop the screw in the computer. Firmly insert the card in the slot and screw the bracket to the chassis. Replace the case. ADC Board (PCI Version) See the PCI-DAS08 User s Manual for installation instructions for the PCI version of the ADC card. IMPORTANT: The PCI Board and supporting software should be installed before the FWT200 software is installed. Then the InstaCal program should be run and the PCI-DAS08 board added to the list of recognized boards. Connecting the Head to the Card Before connecting the head to the card you should make sure that the computer is turned off. Connect one end of the supplied cable to the card and the other end to the reader head (the two ends are interchangeable for the ISA card; the cable for connecting to a PCI card has different connectors on the two ends and is FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 1

3 different than the PCI cable for the FWT-100). Securely fasten them by tightening the screws on the connectors. Table 1 - FWT-300 Computer ADC Card Base Address Selection NOTE: Addresses 000 to 0FF hex used by internal I/O Address DIP Switch Settings Dec Hex on on on on on off on off on on on on off on on off on on on off on off off on on on off on on on off on on off on off on off on on off on on off off on on off on off off off on on off on on on on off on off on off on on off on off on on off on off on off on off off on off on off on on on off off on off on off on off off on off on on off off off on off on off off off off on off on on on on on off off on off on on on off off on on off on on off off on off off on on off off on 416 1A0 on on off on off off on 424 1A8 off on off on off off on 432 1B0 on off off on off off on 440 1B8 off off off on off off on 448 1C0 on on on off off off on 456 1C8 off on on off off off on 464 1D0 on off on off off off on 472 1D8 off off on off off off on 480 1E0 on on off off off off on 488 1E8 off on off off off off on 496 1F0 on off off off off off on 504 1F8 off off off off off off on Do not use - Reserved for system Do not use - Reserved for system on off on on on on off off off on on on on off on on off on on on off off on off on on on off on off off on on on off off off off on on on off on on on off on on off off on on off on on off on off on off on on off off off on off on on off on on off off on on off off on off off on on off on off off off on on off FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 2

4 Address DIP Switch Settings Dec Hex Do not use - Reserved for system on on on on off on off off on on on off on off on off on on off on off off off on on off on off 672 2A0 on on off on off on off 680 2A8 off on off on off on off 688 2B0 on off off on off on off 696 2B8 off off off on off on off 704 2C0 on on on off off on off 712 2C8 off on on off off on off 720 2D0 on off on off off on off 728 2D8 off off on off off on off 736 2E0 on on off off off on off 744 2E8 off on off off off on off 752 2F0 on off off off off on off 760 2F8 Do not use - Reserved for system on on on on on off off DEFAULT SETTING off on on on on off off on off on on on off off off off on on on off off Do not use - Reserved for system Do not use - Reserved for system on off off on on off off off off off on on off off on on on off on off off off on on off on off off on off on off on off off off off on off on off off on on off off on off off off on off off on off off on off off off on off off Do not use - Reserved for system on on on on off off off off on on on off off off on off on on off off off off off on on off off off 928 3A0 on on off on off off off 936 3A8 off on off on off off off 944 3B0 Do not use - Reserved for system 952 3B8 Do not use - Reserved for system 960 3C0 on on on off off off off 968 3C8 off on on off off off off 976 3D0 on off on off off off off 984 3D8 off off on off off off off 992 3E0 on on off off off off off E8 Do not use - Reserved for system F0 Do not use - Reserved for system F8 Do not use - Reserved for system FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 3

5 Lamp Replacement The FWT-200 comes with a lamp installed and one spare lamp taped to the inside of the lamp access cover. When the lamp burns out or becomes too dim you should replace it. To replace the lamp first remove the access cover by unscrewing the black thumb screw on the back of the reader head. Remove the access cover and, from the bottom of the reader, unscrew the black thumb screw which holds the lamp in place. Disconnect the lamp from the circuit board by pulling the connector off the board. Remove the lamp and discard it. Insert the new lamp into the holder as far as it will go and tighten the thumb screw just enough to prevent the lamp from moving. Do not over tighten the screw or you may damage the lamp's housing. Attach the lamp's connector to the circuit board. Replace the access cover. Dosimeter Well The FWT-200 has a dosimeter well that accepts FWT-70 Opti-Chromic dosimeters and FWT-160 Neutral Density filters. The lid to the well should be closed whenever you take a reading (zero, dosimeter or filter). Dosimeters are placed in the light path, which is parallel to the front of the reader. A neutral density filter is inserted in the slot on the right side of the well. Drape the filter s identification tab to the right so it will lay between the top of the reader housing and the well lid rather than being draped into the well. Software Version 1.x (for DOS) This software is located in the DOS folder on the CD-ROM. Information on the nstallation and use of the FWT- 200 software, v.1.x for DOS may be found in the file MANUAL1.DOC or Manual.pdf in that folder. Software version 2.x (for Windows) Version 2.x of the FWT-200 software is an applet that communicates with other programs (such as a spreadsheet, database, or word processor) through dynamic data exchange (DDE) links. The applet displays the absorbance, wavelength and any error message, and makes these available to other programs. Installation Insert the CD-ROM into your computer. Use Windows Explorer (or similar) to navigate to the appropriate ISA or PCI directory on the CD-ROM drive. Double-click the setup.exe file to run the setup. Follow the instructions in the setup program to install the software. Running the Software From Window s Start Program menu select FWT200 or FWT200PCI to run the appropriate software for your card. The file will be in the Far West Technology folder if you accepted the default folder during installation. The first time the software is run on a computer it will display the Port Address Setup (or PCI Card Setup) dialog box. In the PCI software select the PCI-DAS08 card from the pull-down list and click the accept button. In the ISA software specify the port address either by entering the address (in hexadecimal) into the address box or by clicking the DIP switch display to indicate how the switches are set on the card. You may then test the address before accepting it. The main display for the software is a box with the menus, wavelength being analyzed and absorbance reading. The only option on the File menu allows you to Exit the program. The only active option on the Help menu will give you information About the software, including the version number. FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 4

6 The Setup menu has five options. Shut Motor Off or Turn Motor On In order to increase the life of the motor you may shut the motor off if you do not plan to use the reader for an extended period of time. Once you shut the motor off the menu option changes so you may turn the motor on and continue reading. NOTE: the motor should automatically stop anytime you exit the program. Neutral Density Filter Check allows you to verify reader performance by analyzing neutral density filters (NDF). When you select this option a dialog box will appear. With the dosimeter well empty and the lid closed, you should click on the zero button. Zeroing will enable the three filter buttons. You may then place any filter into the reader and click the appropriate button to take readings of that filter. Do this for one or more of the filters. The absorbances will display on the screen and are available through a DDE link (see DDE Links section below). The software uses a calibration factor to adjust the ADC readings to absorbance readings. This check will give you the information you need to adjust this calibration factor, if desired (you may also treat the difference between the observed NDF values and the certified values as a bias of the reader). The default calibration factor is 1.9. The calibration factor may be changed using the fwtgain.exe program in the support directory of the CD-ROM. Start the program, enter the reader s serial number. The program will display the current (or default) value for the reader. You may change the value or exit the program without changing the value. Decreasing the gain will decrease the absorbance readings; thus if your NDF readings average about 2% high you would adjust the gain down 2%. Zero allows you to zero the absorbance reading. The reading may change over time a slow drift in zero is normal. Wavelength allows you to select for which wavelength(s) to display absorbance data. Port brings up the Port Address Setup dialog box, discussed above. DDE Links Dynamic Data Exchange (DDE) links allow data to be transferred from one program to another. The FWT200 program allows other programs to access the absorbance reading for a wavelength. The communication is established with a link source of fwt200 (for the ISA version of the program) or fwt200pci (for the PCI version), a topic of data, and an items of a1, a2 and a3 for absorbance at the primary (typically 600 nm), secondary (typically 656 nm) and reference (typically 750 nm) wavelengths, respectively; lbla1, lbla2 and lbla3 are the primary, secondary and reference wavelengths, respectively (for example, 600 nm, 656 nm and 750 nm ); na1, na2, na3, for the absorbances of neutral density filter A (the light filter) at the primary, secondary and reference wavelengths, respectively; nb1, nb2, nb3, for the absorbances of neutral density filter B (the medium filter) at the primary, secondary and reference wavelengths, respectively; nc1, nc2, nc3, for the absorbances of neutral density filter C (the dark filter) at the primary, secondary and reference wavelengths, respectively; wl, for the wavelength; wl is 1 if only the primary wavelength is displayed, it is 2 if only the secondary wavelength is displayed, and it is 3 if both wavelengths are displayed. FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 5

7 Consult the software manual for your spreadsheet, database or word processor to determine its capabilities for DDE communication and the appropriate syntax. In Microsoft Excel the syntax is: =fwt200 data!a1 to have the cell s contents reflect the absorbance reading at the primary wavelength using an ISA card. The pipe character,, separates the program name and topic; an exclamation point,!, separates the topic and item. The fwt200.xls spreadsheet in the support directory on the distribution CD-ROM illustrates how the data may be accessed, how a dose may be determined from default initial absorbance and a lookup table, and how to copy the information as data (rather than links) into another area of the spreadsheet. Troubleshooting If you are having problems with the FWT200 reader or software please check the following: 1. Reader is securely fastened to the ADC card using the cable supplied by Far West Technology. 2. Computer is connected to an appropriate stable power supply and is turned on. We encourage the use of a quality computer, surge protection and any line filter needed to provide the computer with a stable voltage input. 3. The lamp is on. If there is no light first check items 1 and 2 above, then try replacing the lamp, per the directions in the Lamp Replacement section above. 4. The reader s optical path is clear. Be sure there are no dosimeters in the reader. If the above actions do not solve your problem you may check our website ( for additional information on troubleshooting or contact us at: Far West Technology, Inc. 330 S Kellogg Ave, Suite D Goleta, CA USA Tel.: +1 (805) Fax: +1 (805) info@fwt.com When contacting us, please indicate the following: 1. The version of the FWT200 software you are using (see the Help About dialog box) and whether you are using a PCI or ISA card. 2. The version of Windows you are using. 3. The serial number of your reader. 4. Contact information, including contact name, company, location (include country if outside the USA) fax number and address. 5. A complete description of the problem you are experiencing. FAR WEST TECHNOLOGY FWT 200 Opti-Chromic Reader PAGE 6