Moddit. How to install Stance Subframe Collars into a. This guide will quickly go over how to install subframe collars for your Subaru BRZ.
|
|
- Ella Pitts
- 5 years ago
- Views:
Transcription
1 Moddit How to install Stance Subframe Collars into a BRZ This guide will quickly go over how to install subframe collars for your Subaru BRZ. Written By: Jesus Page 1 of 9
2 PARTS: Stance Sub-Frame Collar Bushings (1) Page 2 of 9
3 Step 1 How to install Stance Subframe Collars into a BRZ Installing the Stance sub-frame collars on the BRZ is one of the easiest installs you could do. The install reinforces the bushings at the four contact points in the sub-frame and allows for better road control. The few following steps will take you through the install. The very first thing you will have to do is raise your car on a lift or jack the rear section of the car according to FSM specifications and jacking points Page 3 of 9
4 Step 2 Because there are only four sections you will have to unbolt and then bolt up again. The install is fairly quick. To begin, we will start installing the two front sub-frame collars. In order to ease the install you will have to loosen these bolts and metal panel, so as to not expose it to unwanted forces. On the passenger side you will also have to loosen an under-body panel Following the loosening of the bolts mentioned above proceed to remove the first large bolt pictured here Page 4 of 9
5 Step 3 Once the larger bolt is out of the way (you can remove it completely as the sub-frame wont' come falling down) you can begin wedging the Stance Sub-frame collars into the correct spots. You will notice that the collar with the thickest ridge goes on the bottom. The collar with the smaller ridge goes on the top section of the subframe bushing Page 5 of 9
6 Step 4 In this image you can see how the assembly of the collars should look like. The top collar is simply wedged in between the top of the front subframe bushing and the vehicle's body. The bottom collar also must slide in, except you will be wedging this lower collar in between the bottom part of the front sub-frame bushing and the metal support panel you loosened in step 4. Once all collars are facing the correct way, slide the bolt up and in between all collars and bushing to tighten up to FSM specs. It is very important to note that the thicker ridges of the collars must be facing towards the sub-frame bushing and the flat parts away from it. After you have repeated these steps to the opposing side you are ready to install the rear-most sub-frame collar bushings Page 6 of 9
7 Step 5 The install of the rear sub-frame collar install is a lot more straight forward. Unlike the front portion where you had to loosen a panel to loosen the sub-frame area, here you just un-bolt and re-tighten; read on to see how. Using your Socket, loosen the rear main bushing bolt from the body. This area is located right behind the exhaust muffler. Here after loosening the bolt we posed how you should layout the collar bushings. Because we had previously installed the Tomei Type-60R exhaust which has no muffler, our area to access the rear sub-frame bushing bolts was fairly open. Keep in mind you might have to remove the stock muffler if it is in your way. After holding the sub-frame collars in the correct position to demonstrate their final placement locations, we then slid the bottom collar in first. After securing the lower collar in place on the bolt, we then placed the top collar so that the bolt would pass through both sub-frame collars and the sub-frame bushing Page 7 of 9
8 Step 6 After one side is complete, simply hand tighten the bolt, but keep it loose for now. You will tighten everything down once the other side is in. At the other side or opposing rear sub-frame bushing, simply repeat step 5 and proceed to tighten to factory Spec Page 8 of 9
9 Step 7 Everything should now be in place and you will have completed the Stance Collar Sub-Frame Bushing Install. Again make sure everything is tightened before you step away. This document was last generated on :39:10 AM Page 9 of 9
Rear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5
Rear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5 Supplied Parts: B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear Subframe Mount Insert Front (601-0033) x 2 B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear
More informationModdit. How to Install an OS Giken Differential into a
Moddit How to Install an OS Giken Differential into a Subaru BRZ This guide goes over the steps necessary to remove and install the OS Giken Limited Slip Differential into a Subaru BRZ. This guide may
More informationHow to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ
Moddit How to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ Written By: Terence Chang 2019 www.moddit.com/ Page 1 of 11 TOOLS: Metric Socket Set- 10mm,12mm,14mm,17mm (1) Metric Combination
More informationModdit. How to Install Raceseng S1/S2 Pulley Kit on Subaru BRZ
Moddit How to Install Raceseng S1/S2 Pulley Kit on Subaru BRZ A quick and simple write up on the Raceseng S1/S2 Pulley Kit install on our Subaru BRZ. Written By: Ruthie 2017 www.moddit.com Page 1 of 11
More informationModdit. How to Install a Tomei Front Pipe on a Subaru BRZ. This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen
Moddit How to Install a Tomei Front Pipe on a Subaru BRZ This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen 2017 www.moddit.com Page 1 of 10 INTRODUCTION With the availability
More informationModdit. How to Install Stance Coilovers on a Subaru
Moddit How to Install Stance Coilovers on a Subaru BRZ Let's get LOW (and maybe lighter and stiffer suspension)! In this article, we will install Stance ST- ZN6-XS Coilovers on the FRSport Subaru BRZ.
More informationLightweight Tubular Sway Bar Kit Subaru WRX / STi / 09+ FXT
915250 Lightweight Tubular Sway Bar Kit 2008+ Subaru WRX / STi / 09+ FXT Installation Instructions Congratulations on your purchase of the COBB Lightweight Tubular Sway Bar Kit for your Subaru WRX, STi
More informationModdit. How to Install the HKS Header W/ Cat on a Subaru BRZ
Moddit How to Install the HKS Header W/ Cat on a Subaru BRZ This full write up is a step by step process on the removal of the stock exhaust components, to the install of the HKS header with Cat. Written
More informationMake sure your vehicle is on a level surface prior to starting installation.
Thank you for purchasing the CorkSport Mazdaspeed 3 Front Sway Bar. Our sway bar will help remove the vehicles tendency to overpower the front tires under hard cornering and minimize traction robbing body
More informationBy AM Customer: Dean Smith, Aug. 8, 2014.
Ford Racing Bullitt Axle-Back Exhaust (05-09 GT, GT500) By AM Customer: Dean Smith, Aug. 8, 2014. Tools for the Job: 13mm Wrench 13mm Socket 15mm Socket 15mm Deep Socket Ratchet(s) [I used a bigger one
More informationEibach Pro-System-Plus
Eibach Pro-System-Plus Tools : - Floor Jack - 3 Jack Stands (4 preferred) - 2 wheel stoppers - Car wrench set - Fire torch - Bolt thread locker (use on every bolt you tight) Disclaimer: This guide is not
More informationThis guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationMake sure your vehicle is on a level surface prior to starting installation.
Thank you for purchasing the CorkSport Mazdaspeed 3 Front Sway Bar. Our sway bar will help remove the vehicles tendency to overpower the front tires under hard cornering and minimize traction robbing body
More informationSport Sway Bar Kit Mustang
Sport Sway Bar Kit 22102 2005 Mustang Installation of Hotchkis Front Sway Bar 1F Raising Vehicle Securely block the rear wheels of the vehicle. Use a jack to lift up the front of the vehicle and use jack
More informationFor all Ram x4 Trucks, and all Ram x4 trucks.
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT
More informationSport Coil Springs Chysler 300C SRT-8 05 Dodge Charger SRT-8
Sport Coil Springs 19105 05 Chysler 300C SRT-8 05 Dodge Charger SRT-8 Warning: This installation should be performed by a trained professional. The installation requires lowering of the rear cradle from
More informationTurboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More informationUNDERDOG RACING DEVELOPMENT URD Traction Bar Installation
URD Traction Bar Installation Introduction: UNDERDOG RACING DEVELOPMENT Thank you for choosing the URD Traction Bar for two wheel drive street trucks. More models coming soon! This bar is a true bolt on
More informationSteeda Sport Mustang Lowering Springs (2005+) - Installation Instructions
Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions The below installation instructions work for the following products: Steeda Sport Mustang Lowering Springs (2005+) Please read
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More information9000 Clutch Replacement By Jack Ashcraft
9000 Clutch Replacement By Jack Ashcraft The most usual reason for clutch (and associated parts) replacement in a Saab is clutch slippage. The clutches for the 9000 are very strong and usually will withstand
More informationDODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION
More informationLG CORVETTE GT2 COIL OVERS
LG CORVETTE GT2 COIL OVERS THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Parts Inventory: 1. Assembled Front shock and spring 2. Assembled Rear shock and spring
More informationSport Coil Springs Dodge Magnum, Chrysler 300C Dodge Challenger SRT Dodge Challenger R/T
Sport Coil Springs 19101 - Dodge Magnum, Chrysler 300C 19107 - Dodge Challenger SRT-8 19108 - Dodge Challenger R/T Warning: This installation should be performed by a trained professional. The installation
More informationINSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents:
INSTRUCTION S 350-500 G-Comp Front Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350500.1 G-Comp Subframe, Camaro 350500.2 G-Comp Sway Bar Kit, Camaro 350500.3 Hardware Kit, G-Comp
More informationRemove four screws from radio trim
ZSpeedPerformance Remove four screws from radio trim Radio trim removed, Remove 3 screws from shifter trim. The other screw is under the ash tray. Remove shift knob and remove shifter trim. Use caution
More informationPypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & GT) - Installation Instructions
Pypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & 94-97 GT) - Installation Instructions The below installation instructions work for the following products: Pypes 409 Stainless
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationAlignment Spec. Power Rack & Pinion: 5 degrees positive Camber 0 degrees Toe-In 1/32
333-TCIE237 1967-1969 Chevy Camaro Front Suspension 1968-1972 Chevy Nova Front Suspension 1967-1969 Pontiac Firebird Front Suspension 1-800-984-6259 www.totalcostinvolved.com 1967-1969 Chevy Camaro Front
More informationInstallation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer
Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationAs stated, these are solely based off of how I like to do the Pre-Trip. I give my personal opinions as well as some helpful tips.
Here are our sections: Engine Compartment Drivers Door Fuel Area Coupling System Trailer (Please note in the type of suspension your trailer has) Light Check In-Cab Inspection and Brake Tests You will
More information2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220
PART #30212 2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220 PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM CHECK PART
More informationSTOP---READ THIS FIRST!
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2003-2013 DODGE Ram 2500/3500, 8 LIFT KIT NOTE: * The factory wheels and tires WILL fit on the front of the vehicle once
More informationBBK Caster/Camber Kit (87-93)
BBK Caster/Camber Kit (87-93) Materials in the box 2 Polished Aluminum Plates 2 Steel Strut Mounts 4 Polyurethane Bushings 2 Stud Plates 2 Bushing Sleeves 2 5/8 Flat Washers 2 5/16 Allen Head Bolts 4 5/16
More informationMercedes W123 Front Seat Replacement
Mercedes W123 Front Seat Replacement If your fronts seats are saggy, ripped, springy, stuck, or otherwise in bad shape one easy option is to replace them with a good used seat. This guide will show you
More informationRear Strong-Strut. Installation Instructions
Rear Strong-Strut Installation Instructions Please read instructions completely before installing the rear Strong-Strut Forward Installation of the rear Strong-Strut is quite simple and involves the removal
More informationBBK Long Tube Header and Shorty Mid-pipe (05-10 GT):
Time Required: Approximately 6-8 Hours BBK Long Tube Header and Shorty Mid-pipe (05-10 GT): Tools Required: Floor Jack or Ramps Jack Stands (unless you used a ramp) 5mm, 8mm, 10mm, 12mm, 22mm sockets/open
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationSlowly lower the floor jack. The spring will then come right out.
Jack up the rear, install a set of jack stands and remove the rear tires. Put a floor jack under the lower transverse link (lower control arm) jack up the lower control arm about one inch. With the jack
More informationIntroduction. Rocky Mountain Westy Subaru Conversion Airbox Installation Instructions
Rocky Mountain Westy Subaru Conversion Airbox Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Subaru Conversion Airbox. We pride ourselves in the products we develop
More informationInstallation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #
Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,
More information2010 Camaro SS/V Underbody Brace Installation Instructions
2010 Camaro SS/V6 20104 Underbody Brace Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your Underbody Brace set was designed with the performance and durability
More informationInstallation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models
Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage
More informationCobra IRS Aluminum Differential Bushings (MMIRSB-40.2)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com Cobra IRS Aluminum Differential Bushings (MMIRSB-40.2) The MM front differential
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationELECTRIC BENDING IRON
ELECTRIC BENDING IRON This is intended as a short pictorial essay on the construction of an electrical side bending iron. As the items used may vary from the ones shown here, only limited dimensions are
More informationProduct: Variable Height Spring. Part Numbers: N. Applications: BMW F8x, M2/M3/M
Product: Variable Height Spring Part Numbers: 415-503001-N Applications: BMW F8x, M2/M3/M4 2014-17 Contents in the box: Qty Part # Description 1 00P-0A1646-B Front Passenger Sleeve Assembly 1 00P-0A1645-N
More information2014+ DODGE RAM LIFT KIT PART# STOP! READ THIS FIRST!
NOTE: 2014+ DODGE RAM 2500 8 LIFT KIT PART# 54320 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal,
More informationSteeda S550 Mustang Front Coilover Installation Instructions For Part:
Steeda S550 Mustang Front Coilover Installation Instructions For Part: 555-8170 Tools required 1. Jack 2. Jack stands 3. Torque Wrench 4. 10mm wrench 5. 11mm wrench 6. 17mm wrench 7. 18mm socket 8. Plastic
More informationAMT Motorsport C7 Corvette Camber Kit User s Guide. 8 Upper Control Arm Studs and hardware for rear upper control arm adjustments
AMT Motorsport C7 Corvette Camber Kit User s Guide Thank you for purchasing the AMT Motorsport Camber Kit for the C7 Corvette. We believe this is the most versatile camber kit available on the market,
More informationEibach Pro-Damper Shocks & Struts (05-09 All):
Eibach Pro-Damper Shocks & Struts (05-09 All): Required tools: 3/8 and 1/2 drive ratchets 7, 8, 10, 15, 16, 17, 18, 21 & 22 mm open ended wrenches 8 & 10 mm box end wrenches 10mm socket 13, 15 & 18 mm
More information67 [ ] OR [ ] REAR BRACKETS BARS Shocks Includes: Includes: Includes: Includes:
1967-1969 Firebird Mini Tub 4-Link Install Instructions 1-866-925-1101 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATING OF THE KIT. IF ANY PIECES ARE
More informationInstallation Instructions
86-95 Low Range Off Road Universal Front Shock Tower Kit for Suzuki Samurai (SKU# SSP-UST) Installation Instructions Revised 10/29/13 Suggested Tools: CAUTION: Safety glasses should be worn at all times
More informationtop tip FIt GUIdE FIttING GUIdE HoW to... EssENtIaLs
FIt GUIdE Check the condition of the front balljoints; there s no point in doing all this work only to have to change the front arms again in the near future. HoW to... FIt MK1 FoCUs PoLY BUsHEs Polyurethane
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust STOP Please take time to read and understand
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6570 SPRING HANGER KIT DODGE DAKOTA Congratulations! You were selective enough
More informationINSTALLATION INSTRUCTIONS Unitronic Turbo-Back Exhaust System for MK7 GTI UH026-EXA
Unitronic Turbo-Back Exhaust System for MK7 GTI Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included
More informationTAS002 TORQUE ARM CONVERSION INSTALLATION INSTRUCTIONS Camaro and Firebird Ford 9
TAS002 TORQUE ARM CONVERSION INSTALLATION INSTRUCTIONS 1967-1969 Camaro and Firebird Ford 9 Please take note before proceeding with this installation: This product may interfere with certain exhaust kits.
More information1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions
1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Version 2 (c) 2008 Total Cost Involved Engineering, Inc. All Rights Reserved. Page 1 of
More informationCamaro Torque Arm Install Instructions
1967-1969 Camaro Torque Arm Install Instructions 1-800-984-6259 www.totalcostinvolved.com 67 [429-4202-00] OR 68-69 [429-4202-00] REAR BRACKETS BARS Shocks Includes: Includes: Includes: Includes: 1 REAR
More informationInstallation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets
Installation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the
More informationThrottle Cable Pull - Patent Pending By: NetGain Controls, Inc.
Throttle Cable Pull - Patent Pending By: NetGain Controls, Inc. Powering the future! Installation Guide 2011 All Rights Reserved NetGain Controls, Inc. 1 of 8 Introduction Thank you for purchasing a NetGain
More information13 March F Dodge Adjustable Track bar with Relocation Bracket (I-00201) 1
13 March 2014 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket (I-00201) 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 P/N# 1032011-F UPLEASE READ ALL INSTRUCTIONS
More information1969 Camaro. Concourse Style Disc Brake Conversion Kit Instllation Instructions
Concourse Style Disc Brake Conversion Kit Instllation Instructions 1969 Camaro (1970 Chevelle Kit Shown) This document contains our regular disc brake conversion instructions with the addition of GM assembly
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationINSTALLATION INSTRUCTIONS CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION
INSTALLATION INSTRUCTIONS 68-74 CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationThis Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs
1 2 3 This Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs Thank you for purchasing the CorkSport Mazda
More informationMM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4) The lower spring perch is drilled
More informationINSTALLATION OF HOTCHKIS PERFORMANCE DOUBLE ADJUSTABLE TRAILING ARMS
1215 DOUBLE ADJUSTABLE UPPER TRAILING ARMS 67-70 CHEVROLET B-BODY This installation will require: A hydraulic jack, jack stands The following wrenches or sockets: 15/16 Adjustable wrench (1-1/4 1-9/32
More information1 August Dodge Adjustable Track bar with Relocation Bracket 1
1 August 2017 1032011-1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 DOWNLOAD ENHANCED INSTALL MANUALS AT BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500
More informationCHEVY SILVERADO CREW CAB RX3 Includes models equipped with DEF tank
2007-2017 CHEVY SILVERADO 1500-3500 CREW CAB RX3 Includes models equipped with DEF tank HARDWARE INCLUDED RECOMMENDED TOOLS 1 Passenger Side Front Support Plate 13mm Wrench 1 8-1.25 x 40mm Hex Bolt 13mm
More informationFULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
More informationINSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA
INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA ISNTALLATION DIFFICULTY: Advanced APPROX TIME: 6-8 Hours REQUIRED TOOLS: 14mm-35mm sockets, wrenches, and ratchet 9/16 and 5/8 12
More informationQA1 Caster Camber Plates (79-89 all)
Time Needed: About 2 hours QA1 Caster Camber Plates (79-89 all) Tools Needed: Socket for lug nuts 13/16 or 6 spline tool is the most common, 17mm socket, 15/16 socket, ¾ socket, 9/16 socket, 15/16 wrench,
More informationPlease take time to read and understand these installation instructions.
Please take time to read and understand these installation instructions. CORSA recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationBBK Ceramic Long Tube Headers (99-04 Cobra and Mach 1) - Installation Instructions
BBK Ceramic Long Tube Headers (99-04 Cobra and 03-04 Mach 1) - Installation Instructions The below installation instructions work for the following products: BBK Ceramic Long Tube Headers (99-04 Cobra
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --300 W PONTIAC WAY CLOVIS, CA 93612 local: 559-875-0222 fax: 559-876-2249 toll free: 800-445-3767-- 6446 5.5 REAR AXLE FLIP-KIT 2015+ FORD F-150 2WD SHORT BED Thank you for being
More informationINSTALLATION MANUAL 4.5 I.F.S. SUSPENSION CURR. FORD F150 W/4.2 OR 4.6 LITER PART # 24940
INSTALLATION MANUAL 4.5 I.F.S. SUSPENSION 1997- CURR. FORD F150 W/4.2 OR 4.6 LITER PART # 24940 SJ101402 PART NUMBER : 24940 1997 CURR. FORD F150 W/4.2 OR 4.6 LITER 4.5 SUSPENSION SYSTEM WITH FRONT SPINDLES
More informationJBA Cat4ward Shorty Header Install (05-10 Mustang GT and Bullitt)
JBA Cat4ward Shorty Header Install (05-10 Mustang GT and 08-09 Bullitt) Installation Time: 6-8 Hours (Depending on Tools and Help) Tools Required: 8mm Socket 10 mm Socket 13mm Socket 15mm Deep Socket Ratchet
More informationInstallation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937
Installation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the
More informationYou will be removing the suspension of your vehicle. If you are not comfortable with this or do not have the proper tools, please do not proceed.
Thank you for purchasing the CorkSport Mazda 3 and Mazdaspeed 3 Coilover Kit. This suspension system features 15-way adjustable dampening settings and full length adjustment to meet every driver s handling
More informationDe clunking your MGB rear axle. By Stuart Clarke
De clunking your MGB rear axle By Stuart Clarke Do you have that annoying clunking noise when accelerating or decelerating, or even when you lift off to change gear, well it s possible to resolve the issue
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More information928 Specialists Rear Sway Bar Installation
928 Specialists Rear Sway Bar Installation This document is also available for download on our website (www.928gt.com/rearswaybarinstall.htm). Any new revisions to these original instructions can be found
More informationINSTALLATION GUIDES DekaFlex Connectors DEKAFLEX MC-HL CONNECTOR INSTALLATION GUIDE FOR HAZARDOUS LOCATIONS
INSTALLATION GUIDES DekaFlex Connectors DEKAFLEX MC-HL CONNECTOR INSTALLATION GUIDE FOR HAZARDOUS LOCATIONS INTRODUCTION Dekoron s DekaFlex armored cables are a revolution in the armored cable industry
More informationWHEEL DRIVE GM S-SERIES TRUCKS & SUV S ( 82-95) & ( 96-04) &
1982-2004 2-WHEEL DRIVE GM S-SERIES TRUCKS & SUV S ( 82-95) 8000990-01 & 8000990-02 ( 96-04) 8001020-01 & 8001020-02 Unisteer offers a limited warranty against all manufacturer defects of their kits and
More informationMishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; Cobra)
Mishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; 97-01 Cobra) Installed on: 2000 Mustang GT (manual transmission) Tools: 8mm socket 10mm socket 13mm socket 3/4" wrench
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More informationSubaru WRX Performance Charge-Pipe System, 2015+
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
More information034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit, MkV/MkVI Volkswagen & 8J/8P Audi
034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit, MkV/MkVI Volkswagen & 8J/8P Audi The installation of your 034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit for the 8J/8P
More informationFocus RS Catback
593100 - Focus RS Catback 593100 Focus RS Catback Ford Focus RS 2016-18 Congratulations on your purchase of the COBB Tuning Focus RS Catback Exhaust! The following instructions will assist you through
More informationPage1. ISF Stainless Steel Headers // Part# HDR-004
Congratulations on the purchase of your ISF Stainless Steel Headers and thank you for choosing Sikky Manufacturing. This installation manual is intended to guide you through the removal of the factory
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationFLANGE. Flanges used for
FLANGE FLANGE Flanges with rating class designations 150, 300, 400, 600, 900, 1500, and 2500 in sizes NPS 1 2 through NPS 24 ASME B16.5: Pipe Flanges and Flanged Fittings (NPS 24 ) ASME B16.47: NPS 26
More information1. Start by removing stock air box and inlet feeding from above front bumper (or any aftermarket are filter system you might have).
1. Start by removing stock air box and inlet feeding from above front bumper (or any aftermarket are filter system you might have). 2. Unplug radiator fan (plug is just behind top of bumper on drivers
More informationPypes Polished Shorty Headers (05-10 V6):
Pypes Polished Shorty Headers (05-10 V6): Introduction: The kit comes complete with replacement hardware and gaskets and can be easily done in your driveway. The hardware supplied for install includes
More informationAxle Length. Page 1 of 16
Page 1 of 16 Rear Axle Alignment The edge of the level is against the spinner. You can tell by how far away the reflection of the level is, from the level itself, at the lowest point of the panel, just
More information