ASTRO FF-14NW & FF-14NEW Friction Feeder

Transcription

1 ASTRO FF-14NW & FF-14NEW Friction Feeder PARTS CATALOG

2 This manual is intended solely for the use and information of Astro Machine Corp., its designated agents, customers, and their employees. The information in this guide was obtained from several different sources that are deemed reliable by all industry standards. To the best of our knowledge, that information is accurate in all respects. However, neither Astro Machine Corp. nor any of its agents or employees shall be responsible for any inaccuracies contained herein. All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher.

3 Table of Contents GROUP 1 Mechanical 1 GROUP 2A Electrical Domestic 3 GROUP 2B Electrical Europe 5 GROUP 3 Metering Plate Assembly 7 GROUP 4 Rear Feed Shaft Assembly 8 GROUP 5 Clutch Shaft Assembly 9 GROUP 6 Middle Feed Shaft Assembly 10 GROUP 7 Pull Out Feed Shaft Assembly 11 GROUP 8 Front Feed Shaft Assembly 12 GROUP 9 Arm Guide Assembly 13 GROUP 10 Feeder Base 15 INDEX 16

4 GROUP 1 MECHANICAL 1

5 GROUP 1 - MECHANICAL KEY PART NO. DESCRIPTION QTY KEY PART NO. DESCRIPTION QTY CENTER PLATE WELDMENT MIDDLE FEED SHAFT ASSEMBLY (SEE GROUP 6) SCALE GUIDE TRUARC, # REAR CLOSURE BRAKE STUD SCREW, 4-40 x 5/16, PANHEAD PH PIN RECEPTACLE, CIRCULAR SPRING PIN, 3/32 x 1/ HEX NUT, ADJUSTMENT LEVER OPERATOR SIDE FRAME WELDMENT PULL OUT FEED SHAFT (SEE GROUP 7) SCREW, 6-32 x 1/4, FL HD UNDERCUT FRONT FEED SHAFT ASSEMBLY (SEE GROUP 8) SCREW, x 3/8, PH TRUSS HD ADJUSTMENT SHAFT BALL BEARING HOUSING RUBBER FEED ROLLER ASSEMBLY SCREW, 6-32 x 1/4 PH OVAL CSK HD SCREW, 8-32 x 1/4, PH MS SS UNDERCUT SCREW L/H SIDE GUIDE A SPRING, UPO ROLLER (#1 OF 2) R/H SIDE GUIDE MOTOR BASE R/H SIDE GUIDE BLOCK SUBASSEMBLY REAR FEED SHAFT WITH INNER RACE (SEE GROUP 4) SUPPORT PULLEY ASSEMBLY, 16 GROOVES FRONT COVER WASHER, ID, OD, THICK ARM GUIDE ASSEMBLY (GROUP 9) WASHER METERING PLATE ASSEMBLY (SEE GROUP 3) BELT, 90XLO SCREW, 8-32 x 1/4, BTN HD SOC CAP PULLEY, 16XLO SCREW, 6-32 x 1/2, PH PAN HD. BLK SET SCREW, 8-32 x 1/ SCREW, x 3/8, PH UNDERCUT SS NON-OPERATOR SIDE FRAME COVER WELDMENT MEDIA SUPPORT OPERATOR SIDE FRAME COVER WELDMENT SLIDER SCREW, x 3/4 FL HD PH WASHER, 7/16 OD x ID x 1/ MOTOR ASSEMBLY CURVED DISC SPRING GR HC STEEL SCREW, 6-32 x 1/4 PH PAN HD SLIDER CLUTCH BRACKET, REEL BEARING BELT, TIMING 110XL LINK, SENSOR TRUARC LINK (SHORT) DOUBLE CLUTCH PULLEY ASSEMBLY, GROOVES NUT, SELF LOCKING, BELT, 120XL SENSOR BRACKET PULLEY ASSEMBLY,MOTOR, 14 GROOVES SCREW, x 5/8, SOC. HD SET SCREW, x 3/16, SOC PT WASHER,#10, 3/16 x 3/8 x POWER SWITCH BRACKET LINK, CONNECTING NON-OPERATOR SIDE FRAME SCREW, x 1/4, PH TRUSS HD RUBBER FOOT SENSOR PIVOT SCREW, PAPER GUIDE SENSOR BRACKET HOUSING ASSEMBLY CLAMPING KNOB, x 7/ ROLL PIN, x 3/ WASHER, PLASTIC 3/16 x 7/16 x 1/ FEED CLUTCH ASSEMBLY SCREW, 6-32 x 1/2 PH PAN HD BELT, 160XL FRONT FEED FRAME ROLL PIN, 3/32 x 5/ FRONT FEED COVER PULLEY ASSEMBLY, 16XL GROOVES PULLEY, 14XL GROOVES PULLEY, 12XL GROOVES EXIT SHAFT ASSEMBLY WASHER, PLAIN, 1/4" MOTOR & PUMP, ZINC SCREW, 4-40 x 3/16, UNDERCUT LOCK WASHER, 1/ BALL BEARING HOUSING ASSEMBLY SCREW, 1/4-20 x 1/2, SOC. CAP L/H SIDE GUIDE BLOCK ASSEMBLY CLUTCH SHAFT (SEE GROUP 5) 1 2

6 Group 2A Electrical, Domestic 3

7 GROUP 2A ELECTRICAL, DOMESTIC KEY PART NO. DESCRIPTION QTY KEY PART NO. DESCRIPTION QTY MOTOR ASSEMBLY FRONT FEED FRAME REAR CLOSURE WIRE HARNESS, MEDIA SENSOR WIRE HARNESS ASSEMBLY, SWITCHES SCREW, 4-40 x 5/16, PANHEAD PH COUNTER ASSEMBLY WASHER, #10, 3/16 x 3/8 x SWITCH, 50-21BBA2BA SENSOR BRACKET CAP, BUTTON SWITCH-BLACK SENSOR PIVOT CAP, BUTTON SWITCH-RED SENSOR BRACKET LABEL, GROUND SYMBOL SCREW, x 5/8, SOC. HD POTENTIOMETER ASSEMBLY, SPD. CONT WASHER, PLASTIC, 3/16 x 7/16 x 1/ FRONT COVER CONNECTING LINK POWER SWITCH CLAMPING KNOB, x 7/ WIRE HARNESS, FILTER-POWER INLET LINK (SHORT) WIRE HARNESS, FUSE/POWER INLET NUT, SELF-LOCKING, FUSE HOLDER LF# SENSOR LINK FUSE, 2AMP SLO-BLO FIBEROPTIC SENSOR ASSEMBLY POWER SWITCH BRACKET SCREW, 6-32 x 3/8, PH TRUSS HD WIRE HARNESS, FILTER-FUSE WASHER, PLASTIC, 3/8 x 3/4 x 1/ NON-OPERATOR SIDE FRAME PROGRAMMED SPEED CONTROL TERMINAL BLOCK ASSEMBLY TRANSFORMER, A TERMINAL STRIP SCREW, x 3/8, HEX HD KNOB WIRE HARN., TERM. BLOCK-SPD. CONT FEED CLUTCH ASSEMBLY WIRE HARN., TERM. BLOCK-SPD. CONT CIRCUIT BOARD SUPPORT WIRE HARNESS, TRANS.-TERM. BLOCK FEEDER CONTROLLER BOARD WIRE HARNESS, TRANS.-TERM. BLOCK WIRE HARNESS, TRANSFORMER WIRE SCREW, 6-32 x 1/4, PH PAN HD SCREW, x 1/4, PH TRUSS HD STAR WASHER, #6 EXTERNAL STAR WASHER, # FILTER ASSEMBLY MOTOR BASE WIRE HARNESS, TRANSFORMER-FILTER OPERATOR SIDE FRAME WELDMENT WIRE HARNESS, TRANSFORMER-FILTER 1 4

8 GROUP 2B ELECTRICAL, EUROPE 5

9 GROUP 2B ELECTRICAL, EUROPE KEY PART NO. DESCRIPTION QTY KEY PART NO. DESCRIPTION QTY MOTOR ASSEMBLY WIRE HARNESS, MEDIA SENSOR REAR CLOSURE SCREW, 4-40 x 5/16, PAN HEAD PH WIRE HARNESS ASSEMBLY, SWITCHES WASHER, #10, 3/16 x 3/8 x COUNTER ASSEMBLY SENSOR BRACKET SWITCH, 50-21BBA2BA SENSOR PIVOT CAP, BUTTON SWITCH-BLACK SENSOR BRACKET CAP, BUTTON SWITCH-RED SCREW, x 5/8, SOC. HD LABEL, GROUND SYMBOL WASHER, PLASTIC, 3/16 x 7/16 x 1/ POTENTIOMETER ASSEMBLY, SPD. CONT CONNECTING LINK FRONT COVER CLAMPING KNOB, x 7/ POWER SWITCH LINK (SHORT) WIRE HARNESS, FILTER-POWER INLET NUT, SELF-LOCKING, WIRE HARNESS, FUSE/POWER INLET SENSOR LINK FUSE HOLDER, LF# FIBER OPTIC SENSOR ASSEMBLY FUSE, 2AMP SLO-BLO SCREW, 6-32 x 3/8, PH TRUSS HD POWER SWITCH BRACKET WASHER, PLASTIC, 3/8 x 3/4 x 1/ WIRE HARNESS, FILTER-FUSE PROGRAMMED SPEED CONTROL NON-OPERATOR SIDE FRAME TRANSFORMER, A TERMINAL BLOCK ASSEMBLY SCREW, x 3/8, HEX HD TERMINAL STRIP WIRE HARNESS, TERM. BLOCK-SPD. CONT KNOB WIRE HARNESS, TERM. BLOCK-SPD. CONT FEED CLUTCH ASSEMBLY (SEE GROUP 5) WIRE HARN., TRANSFORMER-TERM. BLOCK CIRCUIT BOARD SUPPORT WIRE HARN., TRANSFORMER-TERM. BLOCK FEEDER CONTROLLER BOARD SCREW, 6-32 x 1/4, PHILLIPS PAN HD WIRE HARNESS, TRANSFORMER WIRE STAR WASHER, #6 EXTERNAL SCREW, x 1/4, PH TRUSS HD FILTER ASSEMBLY STAR WASHER, # WIRE HARNESS, TRANSFORMER-FILTER MOTOR BASE WIRE HARNESS, TRANSFORMER-FILTER OPERATOR SIDE FRAME WIRE HARNESS, TRANSFORMER, JUMPER FRONT FEED FRAME 1 6

10 GROUP 3 METERING PLATE ASSEMBLY 7

11 GROUP 3 METERING PLATE ASSEMBLY KEY PART NO. DESCRIPTION QTY SCREW, x 3/8, SOC CAP SPACER SCREW, 6-32 x 3/16, PH RND HD ZINC DISC SPRING, HIGH CARBON STEEL SCREW, 6-32 x 1/8, PH PAN HD METERING HOLDER BALL, STEEL 0.187D SCREW, x 1/4, PH TRUSS HD METERING PLATE SCREW, 6 x 3/8, PH FLAT SELF-TAPPING, TYPE A 18-8 SS METERING FINGER WASHER, PLASTIC 3/8 x 3/4 x 1/ STUD STUD METERING BRACKET RELEASE BAR ROLL PIN, 3/32 x 7/ LEVER C-CLIP, 1/4 in. (CRESCENT) METERING KNOB S METERING SEGMENT WASHER SCREW, 6-32 x 3/8, PH UNDERCUT SS STAND OFF METERING PLATE COVER SCREW, 6-32 x 3/16 PH FH UNDERCUT SS 3 8

12 GROUP 4 REAR FEED SHAFT ASSEMBLY KEY PART NO. DESCRIPTION QTY REAR FEED SHAFT WITH INNER RACE ROLL PIN, 3/32 x 5/8, STEEL PULLEY ASSEMBLY, 12XL GROOVES RUBBER FEED ROLLER ASSEMBLY SET SCREW, 8-32 x 1/ PULLEY ASSEMBLY, 16 GROOVES WASHER, ID, OD, THICK WASHER 1 9

13 GROUP 5 CLUTCH SHAFT ASSEMBLY KEY PART NO. DESCRIPTION QTY CLUTCH SHAFT PULLEY 16XLO SET SCREW, 8-32 x 1/ TRUARC ROLL PIN, x 3/ HOUSING ASSEMBLY FEED CLUTCH ASSEMBLY DOUBLE CLUTCH PULLEY ASSEMBLY, GROOVES 1 10

14 GROUP 6 MIDDLE FEED SHAFT ASSEMBLY C Roller (Optional For use on Middle Feed Shaft Assembly ONLY) KEY PART NO. DESCRIPTION QTY MIDDLE FEED SHAFT WITH INNER RACE WASHER WASHER, ID, L703 OD, THICK PULLEY ASSEMBLY, 17 GROOVES FEED ROLLER ASSEMBLY (SMOOTH TREAD ROLLER) C FEED ROLLER ASSEMBLY OPTIONAL (HIGH TRACTION SERRATED TREAD ROLLER) 4 FOR USE ON MIDDLE FEED SHAFT ONLY SET SCREW, x 1/4 CUP PT PULLEY, 16XLO SET SCREW, 8-32 x 1/4 1 11

15 GROUP 7 PULL OUT FEED SHAFT ASSEMBLY KEY PART NO. DESCRIPTION QTY PULL OUT FEED SHAFT SET SCREW, 8-32 x 1/ RUBBER FEED ROLLER ASSEMBLY PULLEY ASSEMBLY, 16XL GROOVES ROLL PIN, 3/32 x 5/8 1 12

16 GROUP 8 FRONT FEED SHAFT ASSEMBLY KEY PART NO. DESCRIPTION QTY FRONT FEED SHAFT WITH INNER RACE FEED ROLLER ASSEMBLY (SMOOTH TREAD ROLLER) S FEED ROLLER ASSEMBLY OPTIONAL (HIGH TRACTION SMOOTH TREAD ROLLER) 4 FOR USE ON FRONT FEED SHAFT ONLY SET SCREW, x 1/4 CUP PT PULLEY ASSEMBLY, 16 GROOVES WASHER WASHER, ID, OD, THICK BRAKE SPRING, FEED ROLLER BRAKE THUMBSCREW, BRAKE S Roller (Optional For use on Front Feed Shaft Assembly ONLY) 13

17 GROUP 9 ARM GUIDE ASSEMBLY KEY PART NO. DESCRIPTION QTY SHAFT WHEEL AND BEARING ASSEMBLY TRUARC ARM SCREW, 6-32 x 1/4, PH PAN HD SHAFT SCREW, 6-32 x 1/4, TRUSS. HD. PH. SS SPRING ARM GUIDE SHAFT ARM GUIDE SCREW, 8-32 x 5/16, FL. HD UNDERCUT ARM 4 14

18 GROUP 10 FEEDER BASE KEY PART NO. DESCRIPTION QTY FEEDER BASE ASSEMBLY (INCLUDES ALL COMPONENTS LISTED BELOW) RUBBER FOOT

19 PART NO. GROUP KEY A B A B A B A B A B A B A B A B A B A 5 Index PART NO. GROUP KEY B A B A B A B A B A B A B A B A B A B A B PART NO. GROUP KEY A B B A B A B A B A B

20 PART NO. GROUP KEY A B A B A B A B A B A B A B A B A B A A 58 Index PART NO. GROUP KEY A B A B A B A B A B A B A B A B B B A B A B A B A B A B A B A B A B A B PART NO. GROUP KEY A B A B A B A B A B A C S S

21 NOTES 18

22

23 Copyright Astro Machine Corp. 01/30/2017 PART NUMBER: 100-FF14NW Rev. G.