Shelving with Sloped Shelves

Transcription

1 Shelving with Sloped Shelves Rousseau shelving with sloped shelves provides superior-quality gravity flow storage that integrates perfectly with other products in our Spider family. This unique product is available in a wide range of dimensions and configurationsto fulfill your exact requirements. With an average sloped of 15 degrees, sloped shelves are perfect for rearloading applications ( flow rack ). These units help to create a "first in, first out" ( FIFO ) system. Shelving units without rear access are also available for more conventional storage. Sloped shelves provide optimum visibility for items stored on shelves above the user's eye level. For shelves below this level, the extra angle reduces visibility of the shelf contents. If visibility is more important than flow in your system, we recommend installing lower, right-angle BOX shelves ( 20/21 ). E1F-EE G1F-EE Index Page(s) Shelving with Sloped Shelves Proposals Accessories 95 Components ROUSSEAUMETAL.COM INFO@ROUSSEAUMETAL.COM

2 Shelving with Sloped Shelf Proposals Open Shelving E1T-EE750502* Open and Closed Shelving When ordering, model numbers must be completed as follows : H for posts with smooth finish surface R for posts with perforated surface Unit Unit BOLTED uprights D A WELDED uprights E B 1 for open shelving 2 for closed shelving EXAMPLE : S T- EE Example : S H D 1 T - E E For a starter unit model with smooth finish posts and bolted open uprights, 36" wide, 24" deep, high and with four sloped shelves. *It is possible to replace an 27 sloped shelf with a 20 / 21 right-angle BOX shelf, see page 94. Shown here are several of the most popular shelving models. Proposals include open or closed uprights and sloped shelves; The shelves have perforations for 52 dividers and 57 guides in 1 1/2" increments c/c. Extra perforations have been added on each side for aligning an 52 divider or an 57 guide with the side of the post (this part acts as a side edge and prevents interference between stored items and the post) ; 52 dividers are available for 18 and 24 deep shelving only ; Possibility to replace a sloped shelf with a right-angle BOX shelf ; Closed shelving proposals include back panels and front base ; Open shelving proposals include one back brace. SEE PAGE 94 E1T-EE Closed Shelving E2T-EE B1T-EE B2T-EE Dimensions Number of shelves W D H " S _T-EC S _T-EC S _T-EC " S _T-EE S _T-EE S _T-EE " S _T-EH S _T-EH S _T-EH " S _T-EJ S _T-EJ S _T-EJ " S _T-EC S _T-EC S _T-EC " 24" S _T-EE S _T-EE S _T-EE " S _T-EH S _T-EH S _T-EH " S _T-EJ S _T-EJ S _T-EJ " S _T-EC S _T-EC S _T-EC " S _T-EE S _T-EE S _T-EE " S _T-EH S _T-EH S _T-EH " S _T-EJ S _T-EJ S _T-EJ " S _T-GC S _T-GC S _T-GC " S _T-GE S _T-GE S _T-GE " S _T-GH S _T-GH S _T-GH " S _T-GJ S _T-GJ S _T-GJ " S _T-GC S _T-GC S _T-GC " 24" S _T-GE S _T-GE S _T-GE " S _T-GH S _T-GH S _T-GH " S _T-GJ S _T-GJ S _T-GJ " S _T-GC S _T-GC S _T-GC " S _T-GE S _T-GE S _T-GE " S _T-GH S _T-GH S _T-GH " S _T-GJ S _T-GJ S _T-GJ " S _T-HC S _T-HC S _T-HC " S _T-HE S _T-HE S _T-HE " S _T-HH S _T-HH S _T-HH " S _T-HJ S _T-HJ S _T-HJ " S _T-HC S _T-HC S _T-HC " 24" S _T-HE S _T-HE S _T-HE " S _T-HH S _T-HH S _T-HH " S _T-HJ S _T-HJ S _T-HJ " S _T-HC S _T-HC S _T-HC " S _T-HE S _T-HE S _T-HE " S _T-HH S _T-HH S _T-HH " S _T-HJ S _T-HJ S _T-HJ END-USERS : DISTRIBUTORS :

3 Shelving with Sloped Shelf Proposals Back-to-Back Open and Closed Shelving E1T-EE751001B E2T-EE751001B B1T-EE751001B B2T-EE751001B Shown here are several of the most popular shelving models. Proposals include open or closed uprights and sloped shelves; The shelves have perforations for 52 dividers and 57 guides in 1 1/2" increments c/c. Extra perforations have been added on each side for aligning an 52 divider or an 57 guide with the side of the post ( this part acts as a side edge and prevents interference between stored items and the post ) ; 52 dividers are available for 18 and 24 deep shelving only ; Possibility to replace a sloped shelf with a right-angle BOX shelf ; Closed shelving proposals include back panels and front base; Open shelving proposals include one back brace. Dimensions Number of shelves W D* H " S _T-EC750801B S _T-EC751001B S _T-EC751201B 48" S _T-EE750801B S _T-EE751001B S _T-EE751201B 60" S _T-EH750801B S _T-EH751001B S _T-EH751201B 72" S _T-EJ750801B S _T-EJ751001B S _T-EJ751201B 36" S _T-EC870801B S _T-EC871001B S _T-EC871201B 36" 48" S _T-EE870801B S _T-EE871001B S _T-EE871201B 60" S _T-EH870801B S _T-EH871001B S _T-EH871201B 72" S _T-EJ870801B S _T-EJ871001B S _T-EJ871201B 36" S _T-EC990801B S _T-EC991001B S _T-EC991201B 48" S _T-EE990801B S _T-EE991001B S _T-EE991201B 60" S _T-EH990801B S _T-EH991001B S _T-EH991201B 72" S _T-EJ990801B S _T-EJ991001B S _T-EJ991201B 36" S _T-GC750801B S _T-GC751001B S _T-GC751201B 48" S _T-GE750801B S _T-GE751001B S _T-GE751201B 60" S _T-GH750801B S _T-GH751001B S _T-GH751201B 72" S _T-GJ750801B S _T-GJ751001B S _T-GJ751201B 36" S _T-GC870801B S _T-GC871001B S _T-GC871201B 42" 48" S _T-GE870801B S _T-GE871001B S _T-GE871201B 60" S _T-GH870801B S _T-GH871001B S _T-GH871201B 72" S _T-GJ870801B S _T-GJ871001B S _T-GJ871201B 36" S _T-GC990801B S _T-GC991001B S _T-GC991201B 48" S _T-GE990801B S _T-GE991001B S _T-GE991201B 60" S _T-GH990801B S _T-GH991001B S _T-GH991201B 72" S _T-GJ990801B S _T-GJ991001B S _T-GJ991201B 36" S _T-HC750801B S _T-HC751001B S _T-HC751201B 48" S _T-HE750801B S _T-HE751001B S _T-HE751201B 60" S _T-HH750801B S _T-HH751001B S _T-HH751201B 72" S _T-HJ750801B S _T-HJ751001B S _T-HJ751201B 36" S _T-HC870801B S _T-HC871001B S _T-HC871201B 48" 48" S _T-HE870801B S _T-HE871001B S _T-HE871201B 60" S _T-HH870801B S _T-HH871001B S _T-HH871201B 72" S _T-HJ870801B S _T-HJ871001B S _T-HJ871201B 36" S _T-HC990801B S _T-HC991001B S _T-HC991201B 48" S _T-HE990801B S _T-HE991001B S _T-HE991201B 60" S _T-HH990801B S _T-HH991001B S _T-HH991201B 72" S _T-HJ990801B S _T-HJ991001B S _T-HJ991201B SEE PAGE 94 * Depth includes two units. Example: 36" = two 18" units. 92 ROUSSEAUMETAL.COM INFO@ROUSSEAUMETAL.COM

4 Shelving with Sloped Shelf Proposals K1F-EE750502* FIFO Open Shelving When ordering, model numbers must be completed as follows : EXAMPLE : Standalone Ending Unit Unit Unit Unit BOLTED uprights J D A C WELDED uprights K E B G S R 1F - EE Example : S R J 1 F - E E For an independant model, with perforated surface posts and bolted, open uprights, 36" wide, 24" deep, high and four sloped shelves. It is possible to replace an 27 sloped shelf with a 20 / 21 right-angle BOX shelf, see page 94. Shown here are several of the most popular shelving models. Proposals include open uprights and sloped shelves; Proposals include two dividing guides per shelf. The guides can be adjusted in 1 1/2" increments c/c ; The shelves have perforations for 52 dividers and 57 guides in 1 1/2" increments c/c. Extra perforations have been added on each side for aligning an 52 divider or an 57 guide with the side of the post ( this part acts as a side edge and prevents interference between stored items and the post ) ; 52 dividers are available for 18 and 24 deep shelving only ; Possibility to replace a sloped shelf with a right-angle BOX shelf ; Proposals include single or double corner gussets ( depending on configuration ). SEE PAGE 94 E1F-DC75041 K1F-DC Standalone Unit B1F-DC G1F-DC Ending Dimensions Number of shelves L P H " _ 1F-EC _ 1F-EC _ 1F-EC " _ 1F-EE _ 1F-EE _ 1F-EE " _ 1F-EH _ 1F-EH _ 1F-EH " _ 1F-EJ _ 1F-EJ _ 1F-EJ " _ 1F-EC _ 1F-EC _ 1F-EC " 24" _ 1F-EE _ 1F-EE _ 1F-EE " _ 1F-EH _ 1F-EH _ 1F-EH " _ 1F-EJ _ 1F-EJ _ 1F-EJ " _ 1F-EC _ 1F-EC _ 1F-EC " _ 1F-EE _ 1F-EE _ 1F-EE " _ 1F-EH _ 1F-EH _ 1F-EH " _ 1F-EJ _ 1F-EJ _ 1F-EJ " _ 1F-GC _ 1F-GC _ 1F-GC " _ 1F-GE _ 1F-GE _ 1F-GE " _ 1F-GH _ 1F-GH _ 1F-GH " _ 1F-GJ _ 1F-GJ _ 1F-GJ " _ 1F-GC _ 1F-GC _ 1F-GC " 24" _ 1F-GE _ 1F-GE _ 1F-GE " _ 1F-GH _ 1F-GH _ 1F-GH " _ 1F-GJ _ 1F-GJ _ 1F-GJ " _ 1F-GC _ 1F-GC _ 1F-GC " _ 1F-GE _ 1F-GE _ 1F-GE " _ 1F-GH _ 1F-GH _ 1F-GH " _ 1F-GJ _ 1F-GJ _ 1F-GJ " _ 1F-HC _ 1F-HC _ 1F-HC " _ 1F-HE _ 1F-HE _ 1F-HE " _ 1F-HH _ 1F-HH _ 1F-HH " _ 1F-HJ _ 1F-HJ _ 1F-HJ " _ 1F-HC _ 1F-HC _ 1F-HC " 24" _ 1F-HE _ 1F-HE _ 1F-HE " _ 1F-HH _ 1F-HH _ 1F-HH " _ 1F-HJ _ 1F-HJ _ 1F-HJ " _ 1F-HC _ 1F-HC _ 1F-HC " _ 1F-HE _ 1F-HE _ 1F-HE " _ 1F-HH _ 1F-HH _ 1F-HH " _ 1F-HJ _ 1F-HJ _ 1F-HJ END-USERS : DISTRIBUTORS :

5 Shelving with Sloped Shelf Components Shelves and Shelf Accessories Sloped Shelf For gravity flow storage ("first in, first out" / FIFO) ; Includes a heavy-duty front edge to keep stored items in place. Front edge height: 1 3 / 8" ; 20 gauge steel shelves (painted steel) ; Shelf is placed on galvanized steel side supports (included) ; Perforations for 52 dividers and 57 dividing guides in 1 1/2'' increments c/c ; 52 dividers are available for 18 and 24 deep shelving only ; Extra perforations have been added to the sides to optimize alignment of the divider or guide with the post and to prevent stored items from falling ; adjustable in 1" increments except if 35 or 36 brackets are used ( in which case, adjustment is in 2" increments ) ; Sloped shelves and non-sloped 20/21 BOX shelves can be combined in the same unit ; Sloped shelf load capacity : 450 lb. ; Compatible with : 99 bases for mobile shelving ; 41 / 43/ 91 / 93 doors with frame* ; 85 flipper doors directly underneath an 27 shelf* ; Drawers directly underneath an 27 shelf* ; 28 bases ; 81 and 82 label holders ; 37/38/66/68/69 and 39 panels. Note: Not compatible with the following products: 50 dividers, 56 dividing rods, 65 and 67 panels, 35 corner gussets. W x D " x 18" " x 24" " x 30" " x 36" " x 18" " x 24" " x 30" " x 36" W x D " x 18" " x 24" " x 30" " x 36" " x 18" " x 24" " x 30" " x 36" *Not compatible with 35 / 36 corner gussets. 27 Box Shelf Box-type shelf with front and rear edges roll-formed and welded ; 20 gauge steel, 1 1 4" thick ; 4 sturdy and compact 60 clips included ; Perforations for dividers (52) at every 3" c/c ; 52 dividers are available for 18 and 24 deep shelving only ; To select your width, add the following to the product number: 30", 36", 42" or 48" ; 20 : Reinforcements are available for these shelves. To see load capacity. 21 : To see load capacities and shelf reinforcements available, refer to the following table. Depth " " 21-30* 30" 21-36* 36" * Double fold on the sides. SEE PAGE Shelf Load Capacity Visual distortion is reduced if an 26 reinforcement and two 23 reinforcements are used on the shelf. Two 24 reinforcements increase the BOX shelf's rigidity ( but does not increase the shelf's load capacity ). Shelves Capacity Without Reinforcement Capacity With 23 Reinforcement Capacity With 23 & 26 Reinforcement Guides DD01 57-DD02 Guides for sloped shelves (version 01) can be used to guide items all the way down ; Width adjustable in 1 1/2" increments ; The front of the guide slots into the fold of the front of the shelf ; The guide is held at the back by a plastic end piece that screws into the shelf holes ; 18" and 24" deep guides use aluminum rods, while 30" and 36" deep guides use stainless steel rods. Dividing guides for BOX shelves (version 02) can be used to separate items ; Width adjustable in 3" increments ; The guide is held at the front and back by a plastic end piece that screws into the shelf holes ; 18" and 24" deep guides use aluminum rods, while 30" and 36" deep guides use stainless steel rods. Heavy-duty black plastic end pieces. Dimensions Depth Sloped Shelf BOX Shelf 18" " " " ROUSSEAUMETAL.COM INFO@ROUSSEAUMETAL.COM

6 Shelving with Sloped Shelf Components Post 10 / 10 Welded Open Upright 11 / 11 Structural Components Tubular T-shape; up to 7 fixing zones; Perforations on sides at every 1" c/c for adjusting shelves; 14 gauge steel; Choose either : 10 universal post with perforated face for adding mini-racking units. Compatible with 35 and 36 corner gussets ; 10 shelving post with smooth face for a superior finish. Not compatible with 35 and 36 corner gussets. Universal Post Shelving Post " " " " The unique shape of the Spider post is a Rousseau Metal Inc. trademark. The maximum height for FIFO application (with 35 / 36 corner gussets) is. Upright with factory welded side braces; Fast assembly; Complete the product number by choosing the desired depth : 18", 24", 30" or 36" ; Choose either : 11 open upright with perforated face for adding mini-racking units. Compatible with 35 and 36 corner gussets ; 11 open upright with smooth face for a superior finish. Not compatible with 35 and 36 corner gussets. Universal Post Shelving Post The maximum height for FIFO application (with 35 / 36 corner gussets) is. Side Braces 34 Welded Closed Upright 12 / 12 Back Sway Brace Sold in pairs; Allow upright assemblies to be fastened in a "ladder-like" manner for easier assembly; Recommendations : 1 pair per upright assembly up to in height For upright assemblies over in height, please refer to the S58 technical sheet or contact your customer service representative. Depth " " " " 33 "X" shaped, factory assembled brace; Easy to install; Recommendations : 1 pair per upright assembly up to in height 2 pairs for posts over in height Please refer to the S58 technical sheet or contact your customer service representative. Upright with full-height factory welded parts; Fast assembly; Complete the product number by choosing the desired depth : 18", 24", 30 or 36 ; Choose either : 12 closed upright with perforated face for adding mini-racking units. Compatible with 35 and 36 corner gussets ; 12 closed upright with smooth face for a superior finish. Not compatible with 35 and 36 corner gussets. Universal Post Shelving Post The maximum height for FIFO application (with 35 / 36 corner gussets) is. Width " " " " Do not use with FIFO shelving. Replace with 35 and 36 corner gusset kits. 95 END-USERS : DISTRIBUTORS :

7 Shelving with Sloped Shelf Components Side Panel 30 Back Panel 31 Shelf Front or Front Base Panel combinations : H posts (39" + 39") H posts (39" + 51") H posts (51" + 51") 111"H posts (39" + 39" + 39") 123"H posts (39" + 39" + 51") Complete the product number by choosing the desired depth : 18", 24", 30" or 36" " " 28 Same component for both applications; Fast hook-on installation; Note : Front base is always included with closed shelving proposals; Complete the product number by choosing the desired width : 30", 36", 42" or 48" " " Structural Perforated Back Panel Panel combinations : H posts (39" + 39") H posts (39" + 51") H posts (51" + 51") 111"H posts (39" + 39" + 39") 123"H posts (39" + 39" + 51") Complete the product number by choosing the desired width : 30", 36", 42" or 48" " " 39 Perforated panel for shelving back; Integrated part of the shelving structure; Holes at every inch c/c; Compatible with WM9F, WM9G, WM9H and WM9J hooks; Compatible with WM9L and WM9K supports; Pannel combinations : H posts (39" + 39") H posts (39" + 51") H posts (51" + 51") Note: Used without the 31 back panels; Complete the product number by choosing the desired width : 30", 36", 42" or 48" " " Double Corner Gusset Kit 35 Double Corner Gusset Kit 36 Replaces back sway brace to provide full access to the front and rear of the shelving ; For use with an aisle-end post or a common post with joined shelves offset by at least 4" in height ; Does not allow two shelves side by side at the same height ; Installs at the front and back of the post ; Compatible with 20, 21 and 27 shelves ; For use with uprights and posts only ; Not compatible with doors with frame, drawers, roll-out shelves and flipper doors ; Note : A minimum of three kits of two 35 or 36 brackets is required per post to provide proper lateral bracing ; Note : Not to be used for shelving over, multi-level shelving or double reinforcement for shelves (C2XXX) pair pairs Replaces sway brace to provide full access to the front and rear of the shelving ; For use with a common post with shelves side by side at the same height ; Installs at the front and back of the post ; Compatible with 20, 21 and 27 shelves ; For use with uprights and posts only ; Not compatible with doors with frame, drawers, roll-out shelves and flipper doors ; Note: A minimum of three kits of two 35 or 36 brackets is required per common post to provide proper lateral bracing ; Note: Not to be used for shelving over, multi-level shelving or double reinforcement for shelves (C2XXX) pair 96 ROUSSEAUMETAL.COM INFO@ROUSSEAUMETAL.COM

8 Shelving with Sloped Shelf Components Installation Accessories Floor Anchor Plate Shim Plate Floor Anchoring Hardware Sold individually; Attaches to the post for anchoring shelving sections to the floor. Distributes the load on a larger surface and protects the floor; 12 gauge galvanized steel. 45 Sold individually; Evens out shelving units on uneven surfaces. Slides under 45 floor anchor plate; 12 or 16 gauge galvanized steel. Thickness gauge (0,100") gauge (0,060") Used for anchoring shelving to the floor; Includes 4 cement screws Wall Spacer Leveling Glides Kit Designed to anchor shelving to the wall; Adjusts from 3" to 4"; Wall anchoring hardware not included (holes are 5 16" in diameter) Serves to adjust the height of the Spider shelving unit 11 4" to 2 1 8" on uneven floor surfaces; Maximum capacity of 750 lb. / glide; Restrictions : Offered for high shelving and less Compatible with posts and uprights only Not compatible with RF32/RF36 drawers, RF41/ RF45 roll-out shelves and the 28 base; Sold in pairs END-USERS : DISTRIBUTORS :