blue series bluepro series

Transcription

1 5Hz water solutions blue series bluepro series DG blue DR blue DG bluepro DR bluepro GR bluepro AP bluepro D a t a b o o k l e t EN

2

3 water solutions blue series bluepro series DG blue DR blue DG bluepro DR bluepro GR bluepro AP bluepro 5Hz D a t a b o o k l e t

4 blue Series blue Series General characteristics Ergonomic technopolymer lifting and carrying handle. Clip floatswitch adjustment. Innovative cable gland system with twin O-rings to ensure maximum tightness. Dry motor with thermal protections. Internal startup capacitor. One silicon carbide mechanical seal (SiC) and one alumina graphite mechanical seal (AL), V-ring in direct contact with the liquid. Oil sump which guarantees longer mechanical seal lifetime, and is easily accessible thanks to a patented system to simplify maintenance procedures. Full free passage allowing the expulsion of solids and preventing fouling of the impeller (DG). Intake strainer in impact-resistant polypropylene (DR). Models available on request with ATEX certification, suitable for installation in the presence of potentially explosive gases, powders and liquids. II G Ex na IIC T Gc Ex h IIC T Gc II G Ex na nc IIC T Gc Ex h IIC T Gc Hydraulic families DG (Draga) Set-back vortex impeller Suitable with slightly soiled biological wastewaters and sewage. Suitable for domestic and residential use page 7 DR (Dreno) page Multi-channel open impeller Can be used with clear or slightly soiled wastewaters containing small solids, strained water, rainwater, seepage and water pumped from underground. Suitable for specifically domestic use Key to product code DRblue 5//GV ABM5 (A) (B) (C) Family 5 Series 6 Power (HPx) / motor poles 7 4 Delivery rate (A) TYPE (GAS thread/flanged) 8 (B) DIAMETER (mm) (C) POSITION 9 V = vertical H = horizontal Hydraulic model Version number Motor size Motor phases M = Single-phase T = Three-phase Power supply voltage frequency 5 = 5Hz 6 = 6Hz blue DATA BOOKLET

5 blue Series Operating ranges H(m) 4 DG blue Q(l/min) Q(m /h) DR blue H(m) Q(l/min) Q(m /h) ZENIT.COM blue

6 blue Series Versions available Electrical variants Single-phase models TC TCG Thermal protection, capacitor Thermal protection, capacitor, floatswitch Cooling system N No cooling and/or seal flushing system Mechanical seals SICAL One silicon carbide mechanical seal (SiC) and one alumina graphite mechanical seal (AL), V-ring Installations Free installation The electric pump, standing on its feet or base, is connected to the delivery flexible pipe using a joint fixed to the discharge. This installation allows to move easily the electrical pump Fixed installation The electric pump, standing on its feet or base, is connected to the delivery pipe, which is screwed to the discharge if threaded, or fixed to a bend if the port is flanged. The pump-hose connection may be threaded or flanged, depending on the pump fitting. Installation with external coupler Available for electric pumps with threaded discharge. The pump unit is supported by a special device fitted to the delivery pipe. This device can be installed at any time without having to empty the tank. It simplifies any maintenance work on the pump, which can be lifted out and resubmerged with great ease. It is recommended in particular for installations of small size, and does not require the pump to be resting on the bottom of the tank. Installation with base coupling foot For submerged installation, available for electric pumps with flanged or threaded horizontal discharge. The coupling device is fixed to the bottom of the tank and the pump is lowered in with the aid of two guide pipes fitted earlier, until the connection to the foot is completed. The delivery pipe is fixed to the coupling device discharge. This device makes routine checks, any maintenance work or replacement of the pump extremely easy, with no need to empty the tank. A specific kit also allowing pumps with vertical discharge to be installed with the base coupling foot is available. blue DATA BOOKLET

7 VORTEX impeller DG blue Pumps with vortex impeller Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power..74 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ½ vertical Free passage max 4 mm Max flow rate 7.7 l/s (46 l/min) Max head.6 m Motor Dry motor with thermal protections. H7RN-F 5 m cable length with schuko plug. Optional m cable length with schuko plug. Mechanical seals One silicon carbide mechanical seal (SiC) and one alumina graphite mechanical seal (AL), V-ring Applications Used with soiled biological wastewaters and sewage. Suitable and reliable for domestic use and residential applications. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials TC, TCG (single-phase models) N SICAL 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Technopolymer Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Paint type Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT ZENIT.COM 7

8 VORTEX impeller DG blue /G4V Performances l/s l/min m /h DG blue 4//G4V ABM DG blue 5//G4V ABM DG blue 75//G4V ABM DG blue //G4V ABM H (m) Characteristic curves according to UNI EN ISO Q (l/min) Q (m /h) Technical data 4 V Phases P (kw) P (kw) A Rpm Start DG blue 4//G4V ABM G ½ 4 mm G ½ 4 mm DG blue 5//G4V ABM G ½ 4 mm G ½ 4 mm DG blue 75//G4V ABM G ½ 4 mm G ½ 4 mm DG blue //G4V ABM G ½ 4 mm G ½ 4 mm Ø Free passage 8 DATA BOOKLET

9 Y VORTEX impeller DG blue Overall dimensions and weights A C E D F B A B C D E F DG blue 4//G4V ABM G ½ 9.5 DG blue 5//G4V ABM G ½ 9 DG blue 75//G4V ABM G ½ 9 5 DG blue //G4V ABM G ½ Dimensions in mm Packaging dimension X Z X Y Z DG blue 4//G4V ABM5 4 4 DG blue 5//G4V ABM5 4 4 DG blue 75//G4V ABM5 4 4 DG blue //G4V ABM5 4 4 Dimensions in mm ZENIT.COM 9

10 MULTI-CHANNEL OPEN impeller DR blue Pumps with multi-channel open impeller Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power..74 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ¼ vertical Free passage max 7 mm Max flow rate 5. l/s (8 l/min) Max head 4. m Motor Dry motor with thermal protections. H7RN-F 5 m cable length with schuko plug. Optional m cable length with schuko plug. Mechanical seals One silicon carbide mechanical seal (SiC) and one lip seal (AL). Applications The ideal solution for use with clear or slightly soiled wastewaters containing small solids, strained water, rainwater, seepage and water pumped from underground. Suitable and reliable for domestic use, including heavy-duty applications. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials TC, TCG (single-phase models) N SICAL 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Technopolymer Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Paint type Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT DATA BOOKLET

11 MULTI-CHANNEL OPEN impeller DR blue /G4V Performances l/s 4 5 l/min m /h DR blue 4//GV ABM DR blue 5//GV ABM DR blue 75//GV ABM DR blue //GV ABM H (m) 4 Characteristic curves according to UNI EN ISO Q (l/min) Q (m /h) Technical data 4 V Phases P (kw) P (kw) A Rpm Start Ø Free passage DR blue 4//GV ABM Dir G G ¼ 5 mm DR blue 5//GV ABM Dir G G ¼ 5 mm DR blue 75//GV ABM Dir G G ¼ 5 mm DR blue //GV ABM DiR G G ¼ 5 mm ZENIT.COM

12 Y MULTI-CHANNEL OPEN impeller DR blue Overall dimensions and weights A C E D F B A B C D E F DR blue 4//G4V ABM G ¼ 5.5 DR blue 5//G4V ABM G ¼ 5 DR blue 75//G4V ABM G ¼ 5.5 DR blue //G4V ABM G ¼ Dimensions in mm Packaging dimension X Z X Y Z DR blue 4//G4V ABM5 4 5 DR blue 5//G4V ABM5 4 5 DR blue 75//G4V ABM5 4 5 DR blue //G4V ABM5 4 5 Dimensions in mm DATA BOOKLET

13 bluepro Series bluepro bluepro Series General characteristics Ergonomic aluminium lifting and carrying handle, coated for excellent mechanical strength and corrosion resistance. Clip floatswitch adjustment. Innovative cable gland system with twin O-rings to ensure maximum tightness. Dry motor with thermal protections. Single-phase models with internal capacitor. Three-phase models with motor protection relay (option). Two silicon carbide mechanical seals (SiC), and V-ring in direct contact with the liquid. Oil sump which guarantees longer mechanical seal lifetime, and is easily accessible thanks to a patented system to simplify maintenance procedures. Breather which allows the air to be vented and ensure reliable pump priming even after long periods out of use. Models available on request with ATEX certification, suitable for installation in the presence of potentially explosive gases, powders and liquids. II G Ex na IIC T Gc Ex h IIC T Gc II G Ex na nc IIC T Gc Ex h IIC T Gc Hydraulic families DG (Draga) Set-back vortex impeller Full free passage allowing the expulsion of solids and preventing fouling of the impeller. Suitable for heavy-duty applications with soiled biological wastewaters, sewage, rainwater and seepage. This electric pump is intended for both domestic and professional use. page 6 DR (Dreno) page Multi-channel open impeller Stainless steel intake strainer and diffuser plate (models 5, 75 and ). Polypropylene intake strainer with cast iron diffuser plate and foot (models 5 and ). Suitable for use with clear or slightly soiled wastewaters containing small solids, strained water, rainwater, seepage and water pumped from underground, where high pumping rates are required. This electric pump is intended for both domestic and professional use. GR (Grinder) Impeller with grinder system Grinder system comprising a revolving cutter and a plate with holes with sharpened edges that fine-chops filaments, preventing fouling of the impeller. Recommended for unstrained civil wastewaters, including those containing filaments or fibres. This electric pump is intended for both domestic and professional use. page 4 AP (Alta prevalenza) page 7 High head impeller Used for clear wastewater, rainwater and seepage containing small amounts of sand. Its high manometric head makes this series suitable for the creation of water features and decorative fountains. This electric pump is intended for both domestic and professional use. ZENIT.COM bluep

14 bluepro Series Operating ranges DG bluepro DR bluepro H(m) 5 H(m) Q(l/min) Q(l/min) 4 Q(m /h) 4 Q(m /h) H(m) 5 GR bluepro H(m) 5 AP bluepro Q(l/min) Q(m /h) Q(l/min) Q(m /h) Key to product code DR bluepro 5//GV ABM5 (A) (B) (C) Family 5 Series 6 Power (HPx) / motor poles 7 4 Delivery rate (A) TYPE (GAS thread/flanged) 8 (B) DIAMETER (mm) (C) POSITION 9 V = vertical H = horizontal Hydraulic model Version number Motor size Motor phases M = Single-phase T = Three-phase Power supply voltage frequency 5 = 5Hz 6 = 6Hz bluep DATA BOOKLET

15 bluepro Series Versions available Electrical variants Single-phase models TC TCG TCDT TCDGT Thermal protection, capacitor Thermal protection, capacitor, float switch Thermal protection, capacitor, startup capacitor, overload protection Thermal protection, capacitor, startup capacitor, overload protection, float switch Three-phase models NAE TR TRG No electric accessories installed Thermal protection, relay for motor protection Thermal protection, relay for motor protection, float switch Cooling system N No cooling and/or seal flushing system Set of mechanical seals SIC Two silicon carbide mechanical seals (SiC), V-ring Installations Free installation The electric pump, standing on its feet or base, is connected to the delivery flexible pipe using a joint fixed to the discharge. This installation allows to move easily the electrical pump Fixed installation The electric pump, standing on its feet or base, is connected to the delivery pipe, which is screwed to the discharge if threaded, or fixed to a bend if the port is flanged. The pump-hose connection may be threaded or flanged, depending on the pump fitting. Installation with external coupler Available for electric pumps with threaded discharge. The pump unit is supported by a special device fitted to the delivery pipe. This device can be installed at any time without having to empty the tank. It simplifies any maintenance work on the pump, which can be lifted out and resubmerged with great ease. It is recommended in particular for installations of small size, and does not require the pump to be resting on the bottom of the tank. Installation with base coupling foot For submerged installation, available for electric pumps with flanged or threaded horizontal discharge. The coupling device is fixed to the bottom of the tank and the pump is lowered in with the aid of two guide pipes fitted earlier, until the connection to the foot is completed. The delivery pipe is fixed to the coupling device discharge. This device makes routine checks, any maintenance work or replacement of the pump extremely easy, with no need to empty the tank. A specific kit also allowing pumps with vertical discharge to be installed with the base coupling foot is available. ZENIT.COM bluep

16 VORTEX impeller DG bluepro Pumps with vortex impeller Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power.7.5 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ½ - vertical Free passage max 5 mm Max flow rate.6 l/s (756 l/min) Max head 5. m Motor Dry motor with thermal protections. H7RN-F - 5 m cable length. Optional m cable length. Mechanical seals Two silicon carbide mechanical seals (SiC), V-ring Applications Suitable for heavy-duty applications with soiled biological wastewaters, sewage, rainwater and seepage. This electric pump is intended for both domestic and professional use. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials TC, TCG (single-phase models) NAE, TRG (three-phase models) N SIC 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Cast iron EN-GJL 5 Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Paint type Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT 6 DATA BOOKLET

17 VORTEX impeller DG bluepro /G4V Performances l/s l/min m /h DG bluepro 5//G4V ABM(T) DG bluepro 75//G4V ABM(T) DG bluepro //G4V ABM(T) H (m) Characteristic curves according to UNI EN ISO Q (l/min) Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start DG bluepro 5//G4V ABM Dir G G ½ 4 mm DG bluepro 75//G4V ABM Dir G G ½ 4 mm DG bluepro //G4V ABM Dir G G ½ 4 mm Ø Free passage V Phases P (kw) P (kw) A Rpm Start DG bluepro 5//G4V ABT Dir 4G G ½ 4 mm DG bluepro 75//G4V ABT Dir 4G G ½ 4 mm DG bluepro //G4V ABT Dir 4G G ½ 4 mm Ø Free passage ZENIT.COM 7

18 VORTEX impeller DG bluepro /G5V Performances l/s l/min m /h DG bluepro 5//G5V ACM(T) DG bluepro //G5V ACM(T) H (m) Characteristic curves according to UNI EN ISO Q (l/min) 4 Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start DG bluepro 5//G5V ACM Dir G G 5 mm DG bluepro //G5V ACM Dir G G 5 mm Ø Free passage V Phases P (kw) P (kw) A Rpm Start DG bluepro 5//G5V ACT Dir 4G G 5 mm DG bluepro //G5V ACT Dir 4G G 5 mm Ø Free passage 8 DATA BOOKLET

19 Y VORTEX impeller DG bluepro Overall dimensions and weights A C E D F B A B C D E F DG bluepro 5//G4V ABM(T) G ½ 9 DG bluepro 75//G4V ABM(T) G ½ 9 5 DG bluepro //G4V ABM(T) G ½ A Dimensions in mm E D F C B A B C D E F kg DG bluepro 5//G5V ACM(T) G DG bluepro //G5V ACM(T) G 4 Dimensions in mm Packaging dimension X Z X Y Z DG bluepro 5//G4V ABM(T)5 4 4 DG bluepro 75//G4V ABM(T)5 4 4 DG bluepro //G4V ABM(T)5 4 4 DG bluepro 5//G5V ACM(T) DG bluepro //G5V ACM(T) Dimensions in mm ZENIT.COM 9

20 MULTI-CHANNEL OPEN impeller DR bluepro Pumps with multi-channel open impeller Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power.7.5 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ¼ - vertical Free passage max 5 mm Max flow rate.5 l/s (69 l/min) Max head 7. m Motor Dry motor with thermal protections. H7RN-F - 5 m cable length. Optional m cable length. Mechanical seals Two silicon carbide mechanical seals (SiC), V-ring Applications Suitable for use with clear or slightly soiled wastewaters containing small solids, strained water, rainwater, seepage and water pumped from underground, where high pumping rates are required. This electric pump is intended for both domestic and professional use. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials TC, TCG (single-phase models) NAE, TRG (three-phase models) N SIC 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Cast iron EN-GJL 5 Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Paint type Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT DATA BOOKLET

21 MULTI-CHANNEL OPEN impeller DR bluepro /GV Performances l/s 4 5 l/min m /h DR bluepro 5//GV ABM(T) DR bluepro 75//GV ABM(T) DR bluepro //GV ABM(T) H (m) 4 Characteristic curves according to UNI EN ISO Q (l/min) Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start DR bluepro 5//GV ABM Dir G G ¼ 5 mm DR bluepro 75//GV ABM Dir G G ¼ 5 mm DR bluepro //GV ABM Dir G G ¼ 5 mm Ø Free passage V Phases P (kw) P (kw) A Rpm Start DR bluepro 5//GV ABT Dir 4G G ¼ 5 mm DR bluepro 75//GV ABT Dir 4G G ¼ 5 mm DR bluepro //GV ABT Dir 4G G ¼ 5 mm Ø Free passage ZENIT.COM

22 MULTI-CHANNEL OPEN impeller DR bluepro /G5V Performances l/s l/min m /h DR bluepro 5//G5V ACM(T) DR bluepro //G5V ACM(T) H (m) 5 5 Characteristic curves according to UNI EN ISO Q (l/min) 4 Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start DR bluepro 5//G5V ACM Dir G G x mm DR bluepro //G5V ACM Dir G G x mm Ø Free passage V Phases P (kw) P (kw) A Rpm Start DR bluepro 5//G5V ACT Dir 4G G x mm DR bluepro //G5V ACT Dir 4G G x mm Ø Free passage DATA BOOKLET

23 Y MULTI-CHANNEL OPEN impeller DR bluepro Overall dimensions and weights A C E D F B A B C D E F DR bluepro 5//GV ABM(T) G ¼ 5 DR bluepro 75//GV ABM(T) G ¼ 5.5 DR bluepro //GV ABM(T) G ¼ 5 4 Dimensions in mm A E D F C B A B C D E F kg DR bluepro 5//G5V ACM(T) G DR bluepro //G5V ACM(T) G Dimensions in 4 mm Z Packaging dimension X X Y Z DR bluepro 5//GV ABM(T)5 4 5 DR bluepro 75//GV ABM(T)5 4 5 DR bluepro //GV ABM(T)5 4 5 DR bluepro 5//G5V ACM(T) DR bluepro //G5V ACM(T)5 Dimensions 5 48 in mm ZENIT.COM

24 GRINDER impeller GR bluepro Grinder pumps Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power.74.5 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ½ - DN horizontal Free passage - Max flow rate 5.6 l/s (6 l/min) Max head 7 m Motor Dry motor with thermal protections. H7RN-F - 5 m cable length. Optional m cable length. Mechanical seals Two silicon carbide mechanical seals (SiC), V-ring Applications Recommended for unstrained civil wastewaters, including those containing filaments or fibres. This electric pump is intended for both domestic and professional use. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Cast iron EN-GJL 5 Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Grinding system Paint type TCDT, TCDGT (single-phase models) TR, TRG (three-phase models) N SIC Chromium steel Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT 4 DATA BOOKLET

25 GRINDER impeller GR bluepro /G4H Performances l/s 4 5 l/min m /h GR bluepro //G4H ACM(T) GR bluepro 5//G4H ACM(T) GR bluepro //G4H ACM(T) H (m) 5 Characteristic curves according to UNI EN ISO Q (l/min) 5 5 Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start GR bluepro //G4H ACM Dir G G ½ -DN - GR bluepro 5//G4H ACM Dir G G ½ -DN - GR bluepro //G4H ACM Dir G G ½ -DN - Ø Free passage V Phases P (kw) P (kw) A Rpm Start GR bluepro //G4H ACT Dir 4G G ½ -DN - GR bluepro 5//G4H ACT Dir 4G G ½ -DN - GR bluepro //G4H ACT Dir 4G G ½ -DN - Ø Free passage ZENIT.COM 5

26 Y GRINDER impeller GR bluepro Overall dimensions and weights A J J E G H D F C B A B C D E F G H J J GR bluepro //G4H ACM(T) G ½ GR bluepro 5//G4H ACM(T) G ½ GR bluepro //G4H ACM(T) G ½ Dimensions in mm Packaging dimension X Z X Y Z GR bluepro //G4H ACM(T)5 5 4 GR bluepro 5//G4H ACM(T) GR bluepro //G4H ACM(T) Dimensions in mm 6 DATA BOOKLET

27 HIGH HEAD impeller AP bluepro Pumps with high head impeller Operating ranges H(m) Q(l/min) Q(m /h) Range characteristics Motor power.74.5 kw Poles Insulation class F Degree of protection IP68 Discharge GAS ½ - DN horizontal Free passage 6 mm Max flow rate 7. l/s (46 l/min) Max head 6.6 m Motor Dry motor with thermal protections. H7RN-F - 5 m cable length. Optional m cable length. Mechanical seals Two silicon carbide mechanical seals (SiC), V-ring Applications Used for clear wastewater, rainwater and seepage containing small amounts of sand. Its high manometric head makes this series suitable for the creation of water features and decorative fountains. This electric pump is intended for both domestic and professional use. Versions Electrical variants Cooling system Mechanical seals Operating specifications Max operating temperature PH of treated fluid Viscosity of treated fluid Maximum immersion depth Density of treated fluid Acoustic pressure max Max starts per hour Construction materials TC, TCG (single-phase models) TR, TRG (three-phase models) N SIC 4 C 6 4 mm /s m Kg/dm <7dB Case Cast iron EN-GJL 5 Hydraulic parts Cast iron EN-GJL 5 Impeller Cast iron EN-GJL 5 Nuts and bolts Stainless steel - Class A-7 Standard gasket Rubber - NBR Shaft Stainless steel - AISI 4 Paint type Ecological bicomponent epoxy (~ 8 μm) Installations FREE FIXED with EXTERNAL COUPLER with BASE COUPLING FOOT ZENIT.COM 7

28 HIGH HEAD impeller AP bluepro /G4H Performances l/s l/min m /h AP bluepro //G4H ACM(T) AP bluepro 5//G4H ACM(T) AP bluepro //G4H ACM(T) H (m) Characteristic curves according to UNI EN ISO Q (l/min) 5 5 Q (m /h) Technical data V Phases P (kw) P (kw) A Rpm Start AP bluepro //G4H ACM Dir G G ½ -DN - AP bluepro 5//G4H ACM Dir G G ½ -DN - AP bluepro //G4H ACM Dir G G ½ -DN - Ø Free passage V Phases P (kw) P (kw) A Rpm Start AP bluepro //G4H ACT Dir 4G G ½ -DN - AP bluepro 5//G4H ACT Dir 4G G ½ -DN - AP bluepro //G4H ACT Dir 4G G ½ -DN - Ø Free passage 8 DATA BOOKLET

29 Y HIGH HEAD impeller AP bluepro /G4H Overall dimensions and weights A J J D F C E G H B A B C D E F G H J J AP bluepro //G4H ACM(T) G ½ AP bluepro 5//G4H ACM(T) G ½ AP bluepro //G4H ACM(T) G ½ Dimensions in mm Packaging dimension X Z X Y Z AP bluepro //G4H ACM(T)5 5 4 AP bluepro 5//G4H ACM(T) AP bluepro //G4H ACM(T) Dimensions in mm ZENIT.COM 9

30 blue Series Hydraulic performance data For quick, easy reference DG blue DG blue 4//G4V ABM DG blue 5//G4V ABM DG blue 75//G4V ABM DG blue //G4V ABM DR blue DR blue 4//GV ABM DR blue 5//GV ABM DR blue 75//GV ABM DR blue //GV ABM DG bluepro DG bluepro 5//G4V ABM(T) DG bluepro 75//G4V ABM(T) DG bluepro //G4V ABM(T) DG bluepro 5//G5V ACM(T) DG bluepro //G5V ACM(T) DR bluepro DR bluepro 5//GV ABM(T) DR bluepro 75//GV ABM(T) DR bluepro //GV ABM(T) DR bluepro 5//G5V ACM(T) DR bluepro //G5V ACM(T) GR bluepro GR bluepro //G4H ACM(T) GR bluepro 5//G4H ACM(T) GR bluepro //G4H ACM(T) AP bluepro AP bluepro //G4H ACM(T) AP bluepro 5//G4H ACM(T) AP bluepro //G4H ACM(T) blue DATA BOOKLET

31

32 water solutions All data made available remain non-binding. Zenit reserves the right to make unannounced product changes it deems appropriate. Rev. - //7