Section 4. Axial Fans - Section 4

Size: px
Start display at page:

Download "Section 4. Axial Fans - Section 4"

Transcription

1 Axial Flow Fans

2 Section 4 Fläkt Woods offers a wide range of axial flow fans for general air movement and special applications such as emergency high temperature smoke extract and pressurisation. ATEX fans for explosive atmospheres and multistage options for increased pressure development. All fans are tested to the latest internationally recognised standard IS05801 Part 1 (1997), installation category D (AMCA approved) for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance. Coupled with the above fan diameters, the adjustable pitch Aerofoil impeller gives the exact performance required, with a non overloading fan characteristic. Axial Fans - Section 4

3 Section 4 - Aerofoil - JM Aerofoil

4 Aerofoil - JM Aerofoil Section 4 Eleven sizes are offered from 315mm to 1000mm diameter. Volume flows of up to 19m 3 /s Static pressures up to 800 Pa High energy efficiency Sizes 31JM - (315mm) to 100JM - (1000mm). Larger sizes up to 2800mm diameter are also available. Please enquire. Fan Performance All fans are tested to the latest internationally recognised standard IS05801 Part 1 (1997), installation category D (AMCA approved) for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance. Coupled with a wide range of fan diameters, the adjustable pitch Aerofoil impeller gives the exact performance required, with a non overloading fan characteristic. Impellers A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable pitch angle availability. The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise. Every cast aluminium component is X-ray examined using Real Time Radiography inspection prior to assembly. The maximum pitch angles shown allow for speed control by frequency inverter (3ph only). Motors Low installed noise levels Motor protection IP55 All casings are hot dipped galvanised Overheat protection is fitted as standard Inverter controllable All motors are totally enclosed air stream rated class F insulation. Constructed from aluminium or cast iron as standard with special T slot or pad mounted fixings. Single speed motors are suitable for speed control by voltage regulation where indicated. Three phase motors are suitable for use with frequency inverters. Two speed motors where available are pole change type. Suitable for horizontal through to vertical shaft operation. Supplied IP55, with removable drain plugs. Sealed for life bearings lubricated with wide temperature range grease. The BT, CT, F22 and PM112 motors are all fitted with overheat protection thermostat as standard. D motors are fitted with Thermistor OHP. These motors are suitable for inverter speed control down to 20% of full speed. Section 4 - Aerofoil - JM Aerofoil Electrical Supply V / 50 Hz / 1 φ V / 50 Hz / 3 φ Temperature Range -40 C to 50 C as standard. (All motors are not suitable for starting at temperatures lower than -20 C.) Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. Other fans can be operated up to 70 C with appropriate deration of motors. Most standard 3φ fans can be offered for a one off emergency operation at 200 C for 2 hours. Casings JM Aerofoil fans are available in either a long cased form, complete with an externally mounted pre-wired electrical terminal box, or short cased for duct or plate installation. Casings are spun from sheet steel with integral pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for external as well as internal use. Accessories Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets. Electronic and transformer type speed controllers and frequency inverters. Standards available contact your local Express Distributor for more details. See section

5 Summary JM Aerofoil Data Section V / 50 Hz / 1φ Section 4 - Aerofoil - JM Aerofoil Dia. Product Product Speed Sound Electronic m 3 /s at Pa (Static) mm Code Number rev/min Level Speed dba Controller JM/16/4/5/38 DX ME JM/16/2/5/32 DX N/A JM/16/4/5/40 DX ME JM/16/2/5/34 JL N/A JM/16/4/5/40 DX ME JM/16/2/5/28 JL N/A JM/16/4/5/30 JL ME JM/16/4/5/40 DX ME JM/16/2/5/18 JL N/A JM/16/4/5/34 DX ME JM/16/4/5/40 JL ME JM/20/4/6/20 DX ME JM/20/4/6/32 DX ME JM/16/4/5/22 JL ME JM/16/4/5/28 DX ME JM/20/4/6/16 DX ME Full selection details and dimensions see section 4.1 or 9.1 (which covers all accessories) Quick selection guide to the JM Cased Aerofoil fans available Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 75

6 Summary JM Aerofoil Data Section V / 50 Hz / 3φ Dia. Product Product Speed Sound Electronic m3/s at Pa (Static) mm Code Number rev/min Level Speed Inverter dba Controller JM/16/4/5/40 DX ME3.5S FWD JM/16/2/5/36 DX N/A FWD JM/16/4/5/40 DX ME3.5S FWD JM/16/2/5/34 DX N/A FWD JM/16/2/5/40 JL N/A N/A JM/16/4/5/40 DX ME3.2D FWD JM/16/2/5/32 DX N/A FWD JM/16/4/5/30 JL ME3.2D N/A JM/16/4/5/40 DX ME3.2D FWD JM/16/2/5/20 JL N/A N/A JM/20/2/6/34 EX N/A FWD JM/16/4/5/34 DX ME3.2D FWD JM/16/4/5/40 JL ME3.2D N/A JM/20/4/6/20 JL ME3.2D N/A JM/20/4/6/32 DX ME3.2D FWD JM/20/4/6/40 JL ME3.2D N/A JM/20/2/6/24 EX N/A FWD JM/20/2/6/34 DX N/A FWD JM/16/4/5/24 JL ME3.2D N/A JM/16/4/5/32 DX ME3.2D FWD JM/20/4/6/36 DX ME3.2D FWD JM/20/2/6/24 EX N/A FWD JM/20/6/6/22 JL ME3.2D N/A JM/20/6/6/34 JL ME3.2D N/A Section 4 - Aerofoil - JM Aerofoil JM/20/4/6/22 DX ME3.2D FWD JM/20/4/6/32 DX AT7.0 FWD JM/20/6/6/22 JL ME3.2D FWD JM/20/6/6/36 EX N/A FWD JM/20/4/6/20 DX N/A FWD JM/20/4/6/24 EX N/A FWD JM/20/6/6/28 EX N/A FWD JM/20/6/6/36 JL N/A FWD JM/20/4/6/24 JL N/A FWD JM/25/4/9/22 EX N/A FWD JM/25/4/9/26 EX N/A FWD JM/25/8/9/34 JL N/A FWD JM/25/6/6/32 EX N/A FWD JM/25/6/9/24 JL N/A FWD JM/25/4/9/22 EX N/A FWD JM/25/4/9/30 EX N/A FWD JM/25/8/9/24 JL N/A FWD JM/25/6/6/22 EX N/A FWD JM/25/6/9/34 JL N/A FWD JM/25/4/6/22 EX N/A FWD JM/25/4/9/20 JL N/A FWD JM/25/4/9/24 EX N/A FWD Full selection details and dimensions see section

7 Aerofoil fan 31JM - 35JM Section Pole 2 Pole Section 4 - Aerofoil - JM Aerofoil 31JM/16/4/5/... 35JM/16/4/5/... 31JM/16/2/5/... Product Speed m3/s at Pa (Static) Code rev/min JM/16/4/5/ JM/16/2/5/ JM/16/4/5/ JM/16/2/5/ JM/16/2/5/ Electrical Data 35JM/16/2/5/ V/50Hz/1φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 230V) (at 230V) Ref Elec- Trans- Level ( ) (kw) (A) (A) tronic former dba 31JM/16/4/5/ BT5/4 DX CD1705 ME1.1 MT JM/16/2/5/ BT9 DX CD1705 N/A N/A 61 35JM/16/4/5/ BT4 DX CD1705 ME1.1 MT JM/16/2/5/ CT5 JL CD1705 N/A N/A V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) (kw) (A) (A) tronic former dba 31JM/16/4/5/ BT5/4 DX CD1344 ME3.5S MT3.0.5 FWD JM/16/2/5/ BT9 DX CD1344 N/A N/A FWD JM/16/4/5/ BT4 DX CD1344 ME3.5S MT3.0.5 FWD JM/16/2/5/ CT5 DX CD1344 N/A N/A FWD JM/16/2/5/ CT9 JL CD1344 N/A N/A N/A 66 BT4-3φ Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 77

8 Aerofoil fan 31JM - 35JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Long Cased 31JM BT4/ JM BT JM BT4/CT JM CT Short Cased 31JM BT4/ JM BT JM BT4/ JM CT JM CT All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which covers all accessories) 78

9 Aerofoil fan 40JM - 45JM Section Pole 2 Pole Section 4 - Aerofoil - JM Aerofoil 40JM/16/4/5/... 45JM/16/4/5/... 40JM/16/2/5/... 45JM/16/2/5/... 45JM/20/2/6/... Product Speed m 3 /s at Pa (Static) Code rev/min JM/16/4/5/ JM/16/2/5/ JM/16/4/5/ JM/16/4/5/ JM/16/2/5/ JM/20/2/6/ Electrical Data V/50Hz/1φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 230V) (at 230V) Ref Elec- Trans- Level ( ) (kw) (A) (A) tronic former dba 40JM/16/4/5/ 1420 BT9 DX CD1705 ME1.3 MT JM/16/2/5/ 2840 CT9 JL CD1705 N/A N/A 66 45JM/16/4/5/ 1420 BT9 JL CD1705 ME1.3 MT JM/16/4/5/ 1420 CT5 DX CD1705 ME1.3 MT JM/16/2/5/ 2840 CT9 JL CD1705 N/A N/A V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) (kw) (A) (A) tronic former dba 40JM/16/4/5/ 1420 BT9 DX CD1559 ME3.2D MT3.1 FWD JM/16/2/5/ 2840 CT9 DX CD1344 N/A N/A FWD JM/16/4/5/ 1420 BT9 JL CD1559 ME3.2D MT3.1 N/A 52 45JM/16/4/5/ 1420 CT5 DX CD1559 ME3.2D MT3.2 FWD JM/16/2/5/ 2840 CT9 JL CD1344 N/A N/A N/A 66 45JM/20/2/6/ 2910 F22 EX CD1343 N/A N/A FWD4 72 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 79

10 Aerofoil fan 40JM - 45JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Long Cased 40JM BT9:CT JM CT JM BT9:CT JM F Short Cased 40JM BT JM CT JM BT JM CT JM F All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 80

11 Aerofoil fan 50JM Section Pole 2 Pole Section 4 - Aerofoil - JM Aerofoil 50JM/16/4/5/... 50JM/20/4/6/... 50JM/ 20/2/6/... 56JM/20/2/6/... Product Speed m 3 /s at Pa (Static) Code rev/min JM/16/4/5/ JM/16/4/5/ JM/20/4/6/ JM/20/4/6/ JM/20/4/6/ JM/20/2/6/ JM/20/2/6/ For 56JM tabular data see page 83 Electrical Data V/50Hz/1φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 230V) (at 230V) Ref Elec- Trans- Level ( ) (kw) (A) (A) tronic former dba 50JM/16/4/5/ 1420 CT5 DX CD1705 ME1.6 MT JM/16/4/5/ 1420 CT9 JL CD1705 ME1.6 MT JM/20/4/6/ 1420 BT9 DX CD1705 ME1.3 MT JM/20/4/6/ 1420 CT5 DX CD1705 ME1.6 MT V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) (kw) (A) (A) tronic former dba 50JM/16/4/5/ 1420 CT5 DX CD1559 ME3.2D MT3.2 FWD JM/16/4/5/ 1420 CT9 JL CD1559 ME3.2D MT3.2 N/A 59 50JM/20/4/6/ 1420 BT9 JL CD1559 ME3.2D MT3.1 N/A 53 50JM/20/4/6/ 1420 CT5 DX CD1559 ME3.2D MT3.2 FWD JM/20/4/6/ 1420 CT9 JL CD1559 ME3.2D MT3.2 N/A 58 50JM/20/2/6/ 2840 F22 EX CD1343 N/A N/A FWD JM/20/2/6/ 2840 PM112 DX CD1343 N/A N/A FWD6 74 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 81

12 Aerofoil fan 50JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Long Cased 50JM CT JM BT9:CT JM F22/PM Short Cased 50JM BT JM CT JM CT JM F JM PM All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 82

13 Aerofoil fan 56JM - 63JM Section Pole 4 Pole Section 4 - Aerofoil - JM Aerofoil 63JM/20/6/6/... 56JM/20/4/6/... 63JM/20/4/6/... Product Speed m 3 /s at Pa (Static) Code rev/min JM/16/4/5/ JM/16/4/5/ JM/20/4/6/ JM/20/2/6/ JM/20/6/6/ JM/20/6/6/ JM/20/4/6/ JM/20/4/6/ For graphical data of 56JM 2 Pole see page 69 Electrical Data V/50Hz/1φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 230V) (at 230V) Ref Elec- Trans- Level ( ) (kw) (A) (A) tronic former dba 56JM/16/4/5/ 1420 CT5 JL CD1705 ME1.6 MT JM/16/4/5/ 1420 CT9 DX CD1705 ME1.6 MT JM/16/4/5/ 1420 CT9 DX CD1705 ME1.6 MT JM/20/4/6/ CT9 DX CD1705 ME1.6 MT JM/20/4/6/ 1420 CT9 DX CD1705 ME1.6 MT V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) (kw) (A) (A) tronic former dba 56JM/16/4/5/ 1420 CT5 JL CD1343 ME3.2D MT3.2 N/A 57 56JM/16/4/5/ 1420 CT9 DX CD1343 ME3.2D MT3.2 FWD1 5 56JM/20/4/6/ 1420 CT9 DX CD1343 ME3.2D AT7.0 FWD JM/20/2/6/ 2910 PM112 EX CD1343 N/A N/A FWD JM/20/6/6/ 900 CT5 JL CD1559 ME3.2D MT3.2 N/A 49 63JM/20/6/6/ 900 CT9 JL CD1559 ME3.2D MT3.2 N/A 50 63JM/20/4/6/ 1420 CT9 DX CD1559 ME3.2D AT7.0 FWD JM/20/4/6/ 1420 F22 DX CD1343 N/A AT7.0 FWD2 61 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 83

14 Aerofoil fan 56JM - 63JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Long Cased 56JM CT JM F JM CT JM F22/PM Short Cased 56JM CT JM CT JM PM JM CT JM CT JM F All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) Wiring diagram references can be found in section

15 Aerofoil fan 71JM - 80JM Section Pole 4 Pole Section 4 - Aerofoil - JM Aerofoil 71JM/20/6/6/... 80JM/20/6/6/... 71JM/20/4/6/... Product Speed m3/s at Pa (Static) Code rev/min JM/20/6/6/ JM/20/6/6/ JM/20/4/6/ JM/20/4/6/ JM/20/6/6/ JM/20/6/6/ JM/20/4/6/ JM/25/4/9/ JM/25/4/9/ JM/20/4/6/... 80JM/25/4/9/... Electrical Data V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Rating Current Current Diagram Sound rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) (kw) (A) (A) tronic former dba 71JM/20/6/6/ 900 CT9 JL CD1559 ME3.2D MT3.2 FWD JM/20/6/6/ 900 F22 EX CD1559 N/A AT7.0 FWD JM/20/4/6/ 1440 F22 EX CD1343 N/A N/A FWD JM/20/4/6/ 1440 PM112 DX CD1343 N/A N/A FWD JM/20/6/6/ 935 F22 EX CD1559 N/A AT7.0 FWD JM/20/6/6/ 935 F22 JL CD1343 N/A N/A FWD JM/20/4/6/ 1440 PM112 JL CD1343 N/A N/A FWD JM/25/4/9/ 1440 PM112 EX CD1343 N/A N/A FWD JM/25/4/9/ 1440 *D132 EX CD1343 N/A N/A FWD6 71 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. * OHP = Thermistor. Maximum pitch angle at 200 = 24. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 85

16 Aerofoil fan 71JM - 80JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Long Cased 71JM CT JM F22/PM JM F22/PM JM D Short Cased 71JM CT JM F JM PM JM F JM PM JM D All dimensions shown in mm For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 86

17 Aerofoil fan 90JM - 100JM Section Pole 6 Pole 90JM/25/8/9/ JM/25/8/9/... 90JM/25/6/6/ JM/25/6/6/ JM/25/6/9/... Section 4 - Aerofoil - JM Aerofoil Product Speed m 3 /s at Pa (Static) Code rev/min JM/25/8/9/ JM/25/6/6/ JM/25/6/9/ JM/25/4/9/ JM/25/4/9/ JM/25/8/9/ JM/25/6/6/ JM/25/6/9/ JM/25/4/6/ JM/25/4/9/ JM/25/4/9/ Pole Electrical Data 90JM/25/4/9/ JM/25/4/9/ V/50Hz/3φ Product Speed Motor Product Pitch Pitch Motor Full Load Starting Wiring Speed Controller Code Number Angle Angle Rating Current Current Diagram Sound rev/min 200 C (at 400V) (at 400V) Ref Elec- Trans- Inverter Level ( ) ( ) (kw) (A) (A) tronic former dba 90JM/25/8/9/ 695 F22 JL CD1343 N/A N/A FWD JM/25/6/6/ 935 F22 JL CD1343 N/A N/A FWD JM/25/6/9/ 935 F22 JL CD1343 N/A N/A FWD JM/25/4/9/ 1450 *D132 EX CD1343 N/A N/A FWD JM/25/4/9/ 1440 *D160 EX CD1343 N/A N/A FWD JM/25/6/6/ 950 F22 JL CD1343 N/A AT7.0 FWD JM/25/6/9/ 960 *D132 JL CD1343 N/A N/A FWD JM/25/4/6/ 1470 *D132 EX CD1343 N/A N/A FWD JM/25/4/9/ 1470 *D160 JL CD1343 N/A N/A FWD JM/25/4/9/ 1470 *D160 EX CD1343 N/A N/A FWD9 79 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Product numbers shown are for Long cased fans. * OHP = Thermistor Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 87

18 Aerofoil fan 90JM - 100JM Section 4.1 Dimensions Long Cased Short Cased Section 4 - Aerofoil - JM Aerofoil Product Motor A B C D E F G H J K L M N P S T U X Max. Fan Code Range Weight (kg) Short Cased 90JM F JM D JM D JM F JM D JM D Long Cased 90JM F JM D JM D JM F JM D JM D All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) Wiring diagram references can be found in section

19 Section 4 - Aerofoil - JM High Temperature

20 Aerofoil - JM High Temperature Section 4.2 Designed for emergency ventilation of hot fire smoke applications 300 C or 400 C for two hours operation, CE marked to EN Sizes from 315mm to 1000mm Sizes 31JM - (315mm) to 100JM - (1000mm). Other sizes are available on request. Fan Performance All fans are tested to the latest internationally recognised standard IS05801 Part 1, installation category D for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance. Coupled with a wide range of diameters, the adjustable pitch Aerofoil impeller gives the exact performance required, with a non overloading fan characteristic. Impellers A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable pitch angle availability. The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise. Every cast aluminium component is X-ray examined using Real Time Radiography inspection prior to assembly. The maximum pitch angles shown allow for speed control by frequency inverter. Motors Fläkt Woods H.T. Series fans utilise a totally enclosed squirrel cage motor. The grades of motor insulation have been selected to meet the specific requirements for each of the H.T. Categories. These motors are suitable for inverter speed control down to 20% of full speed. Electrical Supply 400 V / 50 Hz / 3 φ Temperature Range All casings are hot dipped galvanised Volume flows up to 21m 3 /s Static pressures up to 600 Pa Motor protection IP55 Inverter controllable for ambient temperatures Fans are tested in compliance with high temperature test standard directive 89/106/EEC to EN , and are fully CE marked accordingly. Fläkt Woods H.T. Series fan motors are sized to run the fans continuously at normal ambient temperatures (-40 C to 50 C), as well as operating at their emergency high temperature category. (All motors are not suitable for starting at temperatures lower than -20 C.). Section 4 - Aerofoil - JM High Temperature Most Standard 3 φ fans can be offered for a one off emergency operation at 200 C for 2 hours. Note: During emergency use inverter should be overridden for full speed. Casings JM HT Aerofoil fans are available in either a long cased form, complete with an externally mounted pre-wired electrical terminal box. Casings are spun from sheet steel with integral pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for external as well as internal use. Accessories Silencers, Mounting feet, Spring type vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets. 90

21 JM HT 300/2 Section Pole 2 Pole Section 4 - Aerofoil - JM High Temperature 63JM/20/4/6/... 80JM/20/4/6/ JM/25/4/9/... 31JM/16/2/5/... 40JM/16/2/5/... Product Speed m 3 /s at Pa (Static) Code rev/min JM/16/2/5/ JM/16/2/5/ JM/20/4/6/ JM/20/4/6/ JM/25/4/9/ JM/25/4/9/ JM/25/4/9/ Electrical Data V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Code Number Angle Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level ( ) (kw) (A) (A) dba 31JM/16/2/5/ EF CD1344 FWD JM/16/2/5/ EF CD1344 FWD JM/20/4/6/ L EF CD1344 FWD JM/20/4/6/ L EF CD1344 FWD JM/25/4/9/ M EF CD1343 FWD JM/25/4/9/ M/L EF CD1343 FWD JM/25/4/9/ L EF CD1343 FWD9 81 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Performance shown at emergency operating temperatures. For short cased fans please enquire. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 91

22 JM HT 300/2 Section 4.2 Dimensions Long Cased Long Cased Product Motor A B C D E G H K L M N P S T X Max. Fan Code Range (kg) Weight (kg) 31JM/16/2/5/ JM/16/2/5/ JM/20/4/6/ JM/20/4/6/ JM/25/4/9/ JM/25/4/9/ JM/25/4/9/ All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories). Section 4 - Aerofoil - JM High Temperature 92

23 JM HT 400/2 Section Pole 4 Pole Section 4 - Aerofoil - JM High Temperature 63JM/20/4/6/...71JM/25/4/9/... 80JM/25/4/9/...100JM/31/4/9/... 31JM/16/2/5 35JM/16/2/5/... 40JM/16/2/5/... Product Speed m3/s at Pa (Static) Code rev/min JM/16/2/5/ JM/16/2/5/ JM/16/2/5/ JM/40/4/6/ JM/28/4/9/ JM/25/4/9/ JM/31/4/6/ /JM31/4/6/ /JM31/4/9/ Electrical Data V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Code Number Angle Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level ( ) (kw) (A) (A) dba 31JM/16/2/5/ D80 EF CD1344 FWD JM/16/2/5/ EF CD1344 FWD JM/16/2/5/ EF CD1344 FWD JM/40/4/6/ L EF CD1344 FWD JM/28/4/9/ L EF CD1344 FWD JM/25/4/9/ S EF CD1343 FWD JM/31/4/6/ M EF CD1343 FWD /JM31/4/6/ M EF CD1343 FWD /JM31/4/9/ L EF CD1343 FWD9 86 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Performance shown at emergency operating temperatures. For short cased fans please enquire. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 93

24 JM HT 400/2 Section 4.2 Dimensions Long Cased Product Motor A B C D E G H K L M N P S T X Max. Fan Long Cased Code Range (kg) Weight (kg) 31JM/16/2/5/... D JM/16/2/5/ JM/16/2/5/ JM/20/4/6/... 90L JM/25/4/9/ L JM/25/4/9/ S JM/25/4/9/ M JM/31/4/6/ M JM/31/4/9/... D All dimensions shown in mm. For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) Section 4 - Aerofoil - JM High Temperature 94

25 JM Aerofoil ATEX Section 4.3 Atex standards now available with the Fläkt Woods JM Aerofoil range. Contact your local Express Distributor for further details on availability. Section 4 - Aerofoil - JM ATEX The high specification Industrial Markets in Europe require high specification products for the hazardous application sector. To support our customers Fläkt Woods can offer ATEX compliance on its JM Aerofoil axial fans and its new Centripal EU range of centrifugal fans. This combined range is considered the widest range available from a single manufacturer. What is ATEX? As from July 1, 2003 the new EU ATEX Directive requires most products to be used in potentially explosive environments to be ATEX compliant. The new directive covers a surprisingly large range of equipment including products used in petro-chemical plants, chemicals, pharmaceuticals, battery rooms, flourmills, grain silos and other areas where a potentially explosive atmosphere may be present. Potential explosive hazards are very common and include gases, vapours, mists and dust. The specific mixture being handled categorises the features each product must include. Who does ATEX apply to? End users have the ultimate responsibility to ensure ATEX compliance and Fläkt Woods can assist in this area. Our website provides much of the information and forms required. Manufacturers OEM s Specifiers Distributors Products installed after 1/7/03 may have to be replaced should they not comply with the ATEX directive. Users must act now to specify the correct product. Fläkt Woods ATEX Compliant Fans Fläkt Woods offers both Aerofoil axial fans and Centripal EU range of centrifugal fans that are all ATEX compliant. We have ensured that all the necessary systems are in place during production to continue ATEX compliance. Fläkt Woods have invested heavily in Engineering design and specification to comply with ATEX. Fläkt Woods fans have been modified in a number of ways including changes to motors, materials, locking systems and conduit systems as well as adapting and revising product guides and operation manuals. Acceptance throughout Europe Having the ability to supply ATEX compliance and by CE marking our fans, Fläkt Woods are able to sell fan products anywhere in Europe without further requirements being applied. This also enables refurbishment of existing installations OEM customers can be confident in using Fläkt Woods products to gain the relevant certification of their products. Fläkt Woods Certificate number ST M07 TEC 2885 For more information visit 95

26 JM Aerofoil ATEX Section 4.3 Performance Range covered by The JM ATEX range. Regulation t-box fixings and cable connections as per standard requirements. Section 4 - Aerofoil - JM ATEX 96

27 Section 4 - Aerofoil - JM Bifurcated

28 JM Bifurcated Aerofoil Section mm - 800mm diameter Volume flow up to 7 m 3 /s Static pressures up to 650 Pa Suitable for temperatures up to 200 C Motor protection IP55 Overheat protection fitted as standard Sizes 40JM.Bif - 400mm, 50JM.Bif - 500mm, 63JM.Bif - 630mm, 80JM.Bif - 800mm. 800 and 1000mm JM.Bif available please contact Fläkt Woods for details. Also larger sizes are available, please enquire. Fan Performance Coupled with the above fan diameters the fully adjustable pitch Aerofoil impeller gives the exact performance required with a non overloading fan characteristic. Higher pressures are obtained by multi-staging the Bifurcated Aerofoil fan. Impellers A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable pitch angle availability. The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise. Every component is X-rayed using Real Time Radiography inspection prior to assembly. The maximum pitch angles shown allow for speed control by frequency inverter. Motors All motors are totally enclosed fan cooled class F insulation with protection to IP55. All motors are supplied with sealed for life bearings or extended lubricators. These motors are suitable for inverter speed control down to 20% of full speed. Electrical Supply V / 50 Hz / 3 φ All aluminium cast components are x-ray examined All casings are hot dipped galvanised Multi-stage is available for higher pressures All casings are hot dipped galvanised Inverter speed controllable Section 4 - Aerofoil - JM Bifurcated Temperature Range Up to 200 C continuous operation. Casings Bifurcated fans are available long case only. Long casing covers impeller and motor and has duct mounted terminal box. The hot dipped galvanised casing gives a high resistance to corrosion. Accessories Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Guards, Bell mouth inlets. 98

29 JM Bifurcated Aerofoil Section 4.4 Performance Data Section 4 - Aerofoil - JM Bifurcated Electrical Data 80 C V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Code Number Angle Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level ( ) (kw) (A) (A) dba 40JM.Bif/16/4/5/ 1440 D71C DB N/A 57 40JM.Bif/20/2/6/ 2910 F2225 DB FWD JM.Bif/16/4/5/ 1440 D80C DB FWD JM.Bif/20/2/6/ 2910 F2229 DB FWD JM.Bif/20/4/6/ 1440 F2245 DB FWD C V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Code Number Angle Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level ( ) (kw) (A) (A) dba 40JM.Bif/20/4/6/ F22c JN FWD JM.Bif/20/2/6/ F22c JN FWD JM.Bif/20/4/6/ F22c JN FWD JM.Bif/20/2/6/ F22c JN FWD JM.Bif/20/4/6/ F22c JN FWD2 70 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 99

30 JM Bifurcated Aerofoil Section 4.4 Dimensions 40JM.Bif-50JM.Bif 63JM.Bif - 80JM.Bif Section 4 - Aerofoil - JM Bifurcated Product Motor A B C D E F G H J K L M N P Q S T Weight Code Range (kg) 40JM.Bif/20/4/6/40 F JM.Bif/20/4/6/32 F JM.Bif/20/4/6/32 F JM.Bif/20/4/6/30 F JM.BIF/20/4/6/20 F All dimensions shown in mm For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 100

31 Section 4 - Aerofoil - Bifurcated Series 33

32 JM Bifurcated Series 33 Fan Section mm - 305mm diameter Volume flow up to 0.89 m 3 /s Static pressures up to 380 Pa Sizes 15JM.Bif -152mm, 25JM.Bif - 254mm, 30JM.Bif - 305mm. Fan Performance Ideally suited for exhausting or recirculating fumes, gases and hot air up to temperatures of 200 C. Motor must have access to ambient air. All fans have non overloading characteristics. Impellers Cast in aluminium silicon alloy and has a fixed pitch aerofoil section blade. This ensures strength, reliability and performance at high temperature. Motors All motors are totally enclosed fan cooled, class F insulation with motor protection to IP55. All motors are supplied with sealed for life bearings. Electrical Supply V / 50 Hz / 1 φ V / 50 Hz / 3 φ Temperature Range Up to 200 C For higher temperatures please enquire. Casings All casings are hot dip galvanised for long life and a high resistance to corrosion. A seal is provided on the motor shaft. Accessories Silencers, Mounting feet/plates, Vibration isolators, Matching flanges, High temperature flexible connectors. Suitable for temperatures up to 200 C Motor protection IP55 Series 33 is cost effective solution to Bifurcated applications Section 4 - Aerofoil - Bifurcated Series

33 JM Bifurcated Series 33 Fan Section 4.5 Performance Data Section 4 - Aerofoil - Bifurcated Series 33 Product Speed m 3 /s at Pa (Static) Code rev/min JM JM JM JM Electrical Details V/50Hz/3φ Product Speed Motor Product Motor Full Load Starting Wiring Speed Code Number Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level (kw) (A) (A) dba 25JM.Bif D63C DB CD1344 FWD JM.Bif D71C DB CD1344 FWD JM.Bif D63C DB CD1344 FWD JM.Bif D71C DB CD1344 FWD1 63 Sound pressure levels quoted are average dba at 3 m distance over a sphere, based on form B running under free field conditions, and are presented for comparative purposes only. Cylindrical silencers are available as standard. Bifurcated fans are not suitable for speed regulation. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 103

34 JM Bifurcated Series 33 Fan Section 4.5 Dimensions Product Motor A B C D E H J L M S T Weight Code Range (kg) 15JM.33 D CM JM.33 D CM JM.33 D CM JM.33 D CM JM.33 D CM All dimensions shown in mm For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) Section 4 - Aerofoil - Bifurcated Series

35 JM Aerofoil - 2 Speed Section speed fans offer energy saving characteristics. Fläkt Woods offer a range of 2 speed JM Aerofoil fans on Standard delivery to suit most requirements Section 4 - Aerofoil - JM Aerofoil 2 Speed Performance Data Product Speed m 3 /s at Pa (Static) Code rev/min JM/16/2-4/5/ / JM/16/4-8/5/ / JM/16/2-4/5/ / JM/16/4-8/5/ / JM/20/2-4/6/ / JM/20/4-8/6/ / JM/20/2-4/6/ / JM/20/4-8/6/ / JM/20/4-8/6/ / JM/25/2-4/9/ / JM/20/4-8/6/ / JM/25/4-8/9/ / JM/25/4-8/9/ / JM/25/6-12/9/26 960/ JM/25/4-8/9/ / Performance is shown at highest speed. Electrical Data - Pole Change Type V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Code Number Angle Rating Current Current Diagram Sound EDC22 rev/min (at 400V) (at 400V) Ref Level 2 Speed/ ( ) (kw) (A) (A) dba DOL Starter 40JM/16/4-8/5/ /700 CT5 EL / / /1.0 CD JM/16/2-4/5/ /1440 CT9 EL / / /5.0 CD JM/16/4-8/5/ /700 CT9 EL / / /2.5 CD JM/20/2-4/6/ /1400 PM112 EL / /3.2 78/20 CD JM/20/4-8/6/ /720 F22 EL / / /5.0 CD JM/20/2-4/6/ /1400 PM112 EL / /3.2 78/20 CD JM/20/4-8/6/ /720 F22 EL / / /5.0 CD JM/20/4-8/6/ /700 F22 EL / /2.2 37/7.5 CD JM/25/2-4/9/ /1470 D160 EL / / /32 CD JM/20/4-8/6/ /700 F22 EL / /2.2 37/7.5 CD JM/25/4-8/9/ /730 D132 EL / /2.8 72/14 CD JM/25/4-8/9/ /730 D160 EL / / /27 CD JM/25/6-12/9/26 960/480 D132 EL / /2.3 52/8.5 CD JM/25/4-8/9/ /730 D160 EL / / /27 CD Electrical Data - Dual Wound Type V/50Hz/3φ Product Speed Motor Product Pitch Motor Full Load Starting Wiring Code Number Angle Rating Current Current Diagram Sound EDC19 rev/min (at 400V) (at 400V) Ref Level 2 Speed/ ( ) (kw) (A) (A) dba DOL Starter 31JM/16/2-4/5 2820/ EL / / /2.26 CD Enquire 40JM/16/2-4/5 2885/ L EL / / /4.05 CD Enquire 50JM/20/2-4/6 2875/ M EL / / /6.4 CD Enquire 50JM/20/4-8/6 1460/710 90L EL / / /2.29 CD Enquire 56JM/20/2-4/3 2875/ M EL / / /6.4 CD Enquire 63JM/20/4-8/6 1460/710 90L EL / / /2.29 CD Enquire Sound pressure levels quoted are average db(a) at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 105

36 JM Aerofoil - 2 Speed Section 4.6 Dimensions Long Cased Product Motor A B C D E F G H J K L M N P S T X Max. Fan Code Range Weight (kg) 31JM D JM CT JM CT JM F JM F JM F JM D JM F JM D JM D JM D JM D Section 4 - Aerofoil - JM Aerofoil 2 Speed All dimensions shown in mm For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 106

37 Section 4 - Aerofoil - JM Multi-Stage

38 Aerofoil - JM Multi-Stage Section mm - 800mm diameter Volume flow up to 9 m 3 /s Static pressures up to 1500 Pa High energy efficiency All casings are hot dipped galvanised Sizes 31JM - 315mm, 35JM - 355mm, 40JM - 400mm, 45JM - 450mm, 50JM - 500mm, 56JM - 560mm, 63JM - 630mm, 80JM - 800mm. Fan Performance All fans are tested to the latest internationally recognised standard IS , installation category D for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance. Coupled with the above fan diameters, the adjustable pitch Aerofoil impeller gives the exact performance required, with a non overloading fan characteristic. Impellers A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable pitch angle availability. The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise. Every cast aluminium component is X-ray examined using Real Time Radiography prior to assembly. The maximum pitch angles shown allow for speed control by frequency inverter. Motors All motors are totally enclosed air stream rated class F insulation. Constructed from aluminium as standard with special T slot or pad mounted fixings. Single speed motors are suitable for speed control by frequency inverters. Suitable for horizontal through to vertical shaft operation. Supplied IP55, with removable drain plugs. Sealed for life bearings lubricated with wide temperature range grease. Motors are fitted with thermostat overheat protection as standard. These motors are suitable for inverter speed control down to 20% of full speed. Low installed noise levels Motor protection IP55 Overheat protection fitted as standard Inverter controllable Section 4 - Aerofoil - JM Multi-Stage Electrical Supply V / 50 Hz / 3 φ Temperature Range -40 C to 50 C as standard. (All motors are not suitable for starting at temperatures lower than -20 C.) Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. Other fans can be operated up to 70 C with appropriate deration of motors. Most standard 3φ fans can be offered for a one off emergency operation at 200 C for 2 hours. Casings JM Aerofoil fans are available long cased, complete with an externally mounted pre-wired electrical terminal box. Casings are spun from sheet steel with integral pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for external as well as internal use. Accessories Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets. 108

39 Aerofoil - JM Multi-Stage Section 4.7 Performance Data Section 4 - Aerofoil - JM Multi-Stage Product Speed m3/s at Pa (Static) Code rev/min JM2/16/4/5/40/ JM2/16/4/5/40/ JM2/16/2/5/24/ JM2/16/2/5/27/ JM2/16/4/5/40/ JM2/20/2/6/29/ JM2/20/4/6/41/ JM2/20/2/6/20/ JM2/20/2/6/30/ JM2/20/4/6/30/ JM2/20/4/6/36/ JM2/20/4/6/35/ JM2/25/4/9/40/ JM2/25/4/9/20/ Electrical Data V/50Hz/3φ Product Speed Motor Product Motor Full Load Starting Wiring Speed Code Number Rating Current Current Diagram Controller Sound rev/min (at 400V) (at 400V) Ref Inverter Level (kw) (A) (A) dba 31JM2/16/4/5/40/ BT4 EQ CD1344 FWD JM2/16/4/5/40/ BT5 EQ ENQ FWD JM2/16/2/5/24/ CT5 EQ CD1344 FWD JM2/16/2/5/27/ CT9 EQ CD1344 FWD JM2/16/4/5/40/ CT5 EQ CD1343 FWD JM2/20/2/6/29/ F22 EQ CD1343 FWD JM2/20/4/6/41/ CT9 EQ CD1343 FWD JM2/20/2/6/20/ F22 EQ CD1343 FWD JM2/20/2/6/30/ PM112 EQ CD1343 FWD JM2/20/4/6/30/ CT9 EQ CD1343 FWD JM2/20/4/6/36/ CT9 EQ CD1343 FWD JM2/20/4/6/20/ F22 EQ CD1343 FWD JM2/25/4/9/40/ PM112 EQ CD1343 FWD JM2/25/4/9/20/ PM112 EQ CD1343 FWD7 82 Sound pressure levels quoted are average dba at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only. Speed controllers sized one per two stage fan. Fans that include BT or CT motors can be continuously operated at temperatures up to 70 C. When these fans are operating in excess of 50 C they should be run at full speed only. Product numbers shown are for Long cased fans. For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders. Wiring diagram references can be found in section 9.2. Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 109

40 Aerofoil - JM Multi-Stage Section 4.7 Dimensions Long Cased Product Motor A B C D E F G H J K L M N P S T W X Weight Code (kg) (kg) 31JM2/16/4/5/40/32 BT JM2/16/4/5/40/32 BT JM2/16/2/5/24/20 CT JM2/16/2/5/27/22 CT JM2/16/4/5/40/32 CT JM2/20/2/6/29/24 F JM2/20/4/6/41/32 CT JM2/20/2/6/20/16 F JM2/20/2/6/30/24 PM JM2/20/4/6/30/24 CT JM2/20/4/6/36/28 CT JM2/20/4/6/20/16 F JM2/25/4/9/40/32 PM JM2/25/4/9/20/16 PM Section 4 - Aerofoil - JM Multi-Stage All dimensions shown in mm For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories) 110

41 JM - Accessories Section 4.8 JM Matching Flanges and Flexible Connector Section 4 - JM - Accessories JM Damper Suitable Product Numbers Weight (kg) for fan Matching Flexible C Matching Flexible OA Flange Connector Flange Connection 315 DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA Note: Flexible Connection weight includes two Matching Flanges. Suitable for up to 600 C emergency operation for 2 hours and 200 C continuous. Suitable for Product Weight fan OA Number C D kg Note: Suitable for up to 400 C emergency operation and 200 C continuous. JM Mounting Feet Product Product Frame G L M N P T V W Code Number Size 315 DA BT/CT.F DA BT/CT.F DA BT/CT.F DA BT/CT,F DA BT/CT,F DA BT/CT,F DA BT/CT,F DA BT/CT,F BT/CT,F D F D F D Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 111

42 JM - Accessories Section 4.8 JM Cylindrical Silencers Acoustic Performance B Type (without Pod) Acoustic Performance (db) Octave Band Mid Frequency Hz Bore Dia. Length mm (D) K 2K 4K 8K 315 1D D D D D D D D D D D Acoustic Performance C Type (with Pod) Acoustic Performance (db) Octave Band Mid Frequency Hz Bore Dia. Length mm (D) K 2K 4K 8K 315 1D D D D D D D D D D D Section 4 - JM - Accessories Silencer The above silencers give the following approximate dba reductions: B Type 1 diameter length 7 to 10 dba C Type 1 diameter length 12 to 15 dba For full acoustic details and resistance to airflow for type C see publication SPO1 Suitable Product Numbers Weight (kg) for fan B Type C Type OA (Pod Kit) B C J B Type C Type 315 DS DA M8 ID DS DA M DS DA M DS DA M DS DA M DS DA M DS DA M DS DA M M M M

43 JM - Accessories Section 4.8 Section 4 - JM - Accessories Guard JM Aerofoil Type I & Type II Impeller Side L& S Type Motor Side S Type (BT, CT & F22) Type III Motor Side S Type (D132 & D160) Type IV Bellmouth & LType Motor Side Type II guards have a Ø220 hole cut out of centre. Suitable Type C Weight for fan φa 315 I IV I IV I IV I II IV I II IV I II IV I II III IV I II III IV I II III IV I II III IV I II III IV JM Bell Mouth Inlet Fan with flanged inlet only Suitable Product Numbers C D Weight (kg) for fan φa All dimensions shown in mm Express Range - These products are available from our UK Express Distributor on same day delivery from the date of order. Standard Service - Please consult your local distributor for availability maximum 15 days. 113

44 Section 4 - JM - Accessories

45 Section 4 - JM - Portable Cooler

46 Aerofoil - JM Portable Cooler Section mm 500mm diameter Air throw, up to m/s velocity Purpose built cradle Adjustable discharge angle Aluminium JM aerofoil impeller Sizes 40JM.PC 400mm, 50JM.PC 500mm Fan Performance The fan uses the JM aerofoil impeller set at maximum pitch for the motor to give maximum cooling velocity. Impellers A true aerofoil section high pressure die cast aluminium assembly. All cast aluminium components are X-ray inspected to ensure strength, reliability, performance and safety. Motors All motors are totally enclosed with class F insulation. Protection IP55. All motors are supplied with sealed for life bearings. Electrical Supply V / 50 Hz / 1 φ V / 50 Hz / 1 φ V / 50 Hz / 3 φ Temperature Range -40 C to 50 C For higher temperatures please enquire. 100% X-ray of impeller Heavy duty isolator Motor protection IP55 Motor side and impeller side guards Casing hot dip galvanised Section 4 - JM - Portable Cooler (All motors are not suitable for starting at temperatures lower than -20 C.) Casings Casings are hot dip galvanised with built in conical inlet to ensure performance. The fan is mounted in a heavy duty purpose built tubular frame, a heavy duty isolator is also fitted. Fans are supplied complete with motor side and impeller side safety guards. 116

400mm - 630mm diameter Volume flow up to 7.2m 3 /s ASED 42 Static pressures up to 1000 Pa High energy efficiency All casings are hot dipped galvanised Low installed noise levels protection IP55 Overheat

More information

CASED 24 Designed for emergency ventilation of hot fire smoke applications 300 C or 400 C for two hours operation, CE marked to EN12101-3 2002 All casings are hot dipped galvanised Sizes from 315mm to

More information

Section 4 e c tio - P lat F a n s

Section 4 e c tio - P lat F a n s Plate Fans Section 4 The Fläkt Woods Plate Fan Range is the result of detailed market analysis and intensive research and development by the world leaders in air movement technology. By setting and achieving

More information

ExpressBuild STANDARD FAN RANGE

ExpressBuild STANDARD FAN RANGE AIR COMFORT FIRE SAFETY ExpressBuild STANDARD FAN RANGE OUR SHORT LEAD TIME FAN RANGE ExpressBuild CONCEPT & PRINCIPLES When a short lead time solution is important, choose an ExpressBuild Fan product

More information

MAXFAN COMPAC » OFFERING HIGH PERFORMANCE, ROBUST DESIGN AND FLEXIBLE CONTROL AIR COMFORT FIRE SAFETY AIR MOVEMENT

MAXFAN COMPAC » OFFERING HIGH PERFORMANCE, ROBUST DESIGN AND FLEXIBLE CONTROL AIR COMFORT FIRE SAFETY AIR MOVEMENT AIR COMFORT FIRE SAFETY AIR MOVEMENT MAXFAN COMPAC» OFFERING HIGH PERFORMANCE, ROBUST DESIGN AND FLEXIBLE CONTROL INTRODUCING THE MAXFAN COMPAC THE NEW MAXFAN COMPAC DESIGNED FOR THE KITCHEN CANOPY MARKET

More information

Wide performance ranges are obtained by using three impeller designs to suit all types of applications.

Wide performance ranges are obtained by using three impeller designs to suit all types of applications. Roof Mounted Fans Section 6 Wide performance ranges are obtained by using three impeller designs to suit all types of applications. The roof extract units are designed to satisfy the consultants functional

More information

JM Aerofoil Bifurcated Fans

JM Aerofoil Bifurcated Fans JM Aerofoil Bifurcated Fans JM AEROFOIL - BIFURCATED CONTENTS The Bifurcated Fan Range - Introduction 3 Applications 4 Specification 5 Forms of Running, Test Methods & Quality Systems 6 Guide To Fan Selection

More information

JM Aerofoil Multi-Stage 50 Hz

JM Aerofoil Multi-Stage 50 Hz JM Aerofoil Multi-Stage 5 Hz JM AEROFOIL - MULTI-STAGE CONTENTS Page: JM Aerofoil Multi-Stage - Introduction -5 Multi-Staging Motor Frame Size Schedules - Three Phase 7-8 Performance Curves SK1- SK135

More information

JM Aerofoil Bifurcated 50Hz

JM Aerofoil Bifurcated 50Hz JM Aerofoil Bifurcated 5Hz JM AEROFOIL - BIFURCATED CONTENTS The Bifurcated Fan Range - Introduction 3 Applications 4 Specification 5 Forms of Running, Test Methods & Quality Systems 6 Guide To Fan Selection

More information

Size and Configurations

Size and Configurations !!"#!""!"$%!!" &'()&('& AK Axial Flow Fans the high efficiency direct-driven fan with adjustable pitch impeller specially designed to operate with low noise emission and vibration that meets the stringent

More information

MAJAX-2 GENERAL SPECIFICATION

MAJAX-2 GENERAL SPECIFICATION MAJAX-2 GENERAL SPECIFICATION Majax-2 axial flow fans are manufactured in diameters ranging from 315mm to 2000mm (available in 2250mm on request), and incorporate manually adjustable pitch aluminium bladed

More information

Bifurcated Case Axial Fans (BIFA)

Bifurcated Case Axial Fans (BIFA) Bifurcated Case Axial Fans (BIFA) Sizes 250 to 1000 dia Motors protected to IP55 Motor insulation Class F Maximum ambient temperature 200 C Speed controllable via transformer or inverter (when the ambient

More information

CASED AXIAL BIFURCATED SERIES 33

CASED AXIAL BIFURCATED SERIES 33 76 CASED AXIA BIFURCATED SERIES 33 PRODUCT FACTS Air flow up to 0.95 m 3 /s Static pressures up to 380 Pa Suitable for temperatures up to 200 C Series 33 is cost effective solution to Bifurcated applications

More information

ErP PLASTIC TUBE FANS - ESPADA FEATURES. ELECTRICAL SUPPLY V/50Hz/1f SIZES TEMPERATURE RANGE FEATURES AND CONSTRUCTION PRODUCT CODE

ErP PLASTIC TUBE FANS - ESPADA FEATURES. ELECTRICAL SUPPLY V/50Hz/1f SIZES TEMPERATURE RANGE FEATURES AND CONSTRUCTION PRODUCT CODE 83 PLASTIC TUBE FANS - ESPADA FEATURES mm to 315 mm diameter Air flow up to.35 m 3 /s Static pressures up to 58 Pa Plastic cased centrifugal fan Low noise levels Corrosion resistant design Easy electrical

More information

Sabre Plate Mounted Sickle Fans (VSP)

Sabre Plate Mounted Sickle Fans (VSP) Sabre Plate Mounted Sickle Fans (VSP) Swept impeller with Aerofoil blades, winglets and serrated trailing edge for optimum performance One shot die cast impeller, dynamically balanced for smoother operation

More information

Explanation of AR Series Ventilator Products. Fan type code D S AR AE

Explanation of AR Series Ventilator Products. Fan type code D S AR AE Series Axial Fan Explanation of Series Ventilator Products Fan type code 450-7 /26 D -2 F400 Smoke Extract Fan 400 C, 300 C Number of Poles D S Three Phase Single Phase AE AE Features and construction

More information

Duct mounted fans. axial flow. Pacific HVAC Engineering Tel. Australia NZ

Duct mounted fans. axial flow. Pacific HVAC Engineering Tel. Australia NZ Duct mounted fans axial flow Pacific HVAC Engineering 215 www.pacifichvac.com Tel. Australia 13 733 833 NZ 8 1 326 6 5 4 3 2 1 5 1 15 2 7 6 5 4 3 2 1 3 2.5 2 1.5 1.5 1 15.5 1 1.5 2 2.5 3 3.5 Volume m 3

More information

200mm - 760mm diameter Volume flow up to 9.2m 3 /s Static pressures up to 1000 Pa Four fan types allowing versatility of performance Rugged fibre glass construction casings Completely assembled units Mounting

More information

Hison Axial Flow Fans

Hison Axial Flow Fans Hison Axial Flow Fans Introduction Hison Marine Axial Flow Fans, formerly know as Howden Fans are manufactured to international Quality Standard. Axial flow fans are available from sizes 35mm to 18mm diameter,

More information

Axial fans. What s more, non-stock models are normally available within two weeks.

Axial fans. What s more, non-stock models are normally available within two weeks. Axial fans 7 sees the introduction of a new production line at Xpelair s Peterborough plant for the Scimitar Sickle blade fans in Plate, Short Case and Roof versions up to 63mm. Scimitar will join an impressive

More information

S ACON SEACON SEACO QUIPMEN EQUIPMENTS SEACON EQUIPMENTS

S ACON SEACON SEACO QUIPMEN EQUIPMENTS SEACON EQUIPMENTS S ACON EQ NTS ACON E NTS A S EQ A TS TS TS TS TS E AC AC AC AC AC AC S S UIP IPME IPME QU P QUI QUI EQ EQUI Q EQ EQ EQ EQ EN EN SE SE SEAC AC AC AC AC AC AC ACO EQUIP E MEN SEACO EQUIPMEN A EQU EQU AC

More information

CYLINDRICAL CASED AXIAL FLOW FANS

CYLINDRICAL CASED AXIAL FLOW FANS - Adjustable pitch fans Range of adjustable pitch aerofoil blade, cased axial flow fans. Casings formed from rolled sheet steel with a corrosion resistant hot dipped galvanised finish. All models incorporate

More information

BIFLOW SB CON Product Brochure

BIFLOW SB CON Product Brochure BIFLOW SB CON Brochure Available for next day delivery with ELTA SELECT Bifurcated Conical Axial Flow Fan For full detailed information on the following: Sound Data, Accessories & Wiring Data and Optimum

More information

AXIAL FANS Catalogue CN0050C01 May 2008

AXIAL FANS Catalogue CN0050C01 May 2008 ADTA AXIAL FANS Catalogue CN0050C01 May 2008 ADTA AXIAL FANS Catalogue CN0050C01 May 2008 Construction Specifications Impellers: Breezax aerfoil blades are available in four types of material: Glass Reinforced

More information

Centrifugal performance characteristics with axial flow pattern: RADAX VAR

Centrifugal performance characteristics with axial flow pattern: RADAX VAR High pressure in-line mixed-flow fans RADAX VAR Centrifugal performance characteristics with axial flow pattern: RADAX VAR COMPACT PRESSURE-RESISTANT UNIVERSAL In their compact casing, the RADAX VAR impellers

More information

Hison Axial Flow Fans

Hison Axial Flow Fans Hison Axial Flow Fans Introduction Hison Marine Axial Flow Fans, formerly know as Howden Fans are manufactured to international Quality Standard. Axial flow fans are available from sizes 35mm to 18mm diameter,

More information

supplied in Form (B) configuration. Airflow over Impeller- Motor.

supplied in Form (B) configuration. Airflow over Impeller- Motor. CYLINDRICAL CASED AXIAL FLOW FANS COMPACT Series TCBB-TCBT (Aluminium impellers) and TCFB-TCFT (Plastic impellers) NEW VERSIONS Description The S&P Cylindrical Cased Axial Fans feature, as the name suggests,

More information

DATASHEET 63JMP/20/4/3/32

DATASHEET 63JMP/20/4/3/32 62 ATE HMIDITY FAS SESOR JM STB-02 ATE FA DATASHEET RODCT FACTS Air flow up to 8.17 m 3 /s Static pressures up to 260 a Motor protection I55 Speed controllable Supplied fully assembled Full range of accessories

More information

ErP POWERBOX EC FANS - ESTOC EC FEATURES ELECTRICAL SUPPLY TEMPERATURE RANGE SIZES FEATURES AND CONSTRUCTION PRODUCT CODE IMPELLER MOTOR

ErP POWERBOX EC FANS - ESTOC EC FEATURES ELECTRICAL SUPPLY TEMPERATURE RANGE SIZES FEATURES AND CONSTRUCTION PRODUCT CODE IMPELLER MOTOR 13 POWERBOX EC FANS - ESTOC EC FEATURES Sizes from 3 to 3 mm diameter Air flow up to.1 m 3 /s Static pressures up to Pa Controllable EC motors Multiple outlet orientations ELECTRICAL SUPPLY 22-2V/Hz/1f

More information

Sabre Sickle Fan Assisted Roof Cowls (VSR)

Sabre Sickle Fan Assisted Roof Cowls (VSR) Sabre Sickle Fan Assisted Roof Cowls (VSR) Swept impeller with Aerofoil blades, winglets and serrated trailing edge for optimum performance Fully assembled cowl, separate plate axial fan Optional backdraught

More information

TGT Series Adjustable Pitch Fans

TGT Series Adjustable Pitch Fans CYLINDRICAL CASED AXIAL FLOW FANS TGT Series Adjustable Pitch Fans Range of adjustable pitch aerofoil blade, cased axial flow fans.casings formed from rolled sheet steel with a corrosion resistant hot

More information

Short casing. Long casing (L version) Commercial premises

Short casing. Long casing (L version) Commercial premises CYLINDRICAL CASED AXIAL FLOW FANS TGT Series Adjustable Pitch Fans Long casing (L version) Short casing A P P L I C A T I O N S Range of adjustable pitch cased axial flow fans. Casings formed from rolled

More information

Square Duct Fans - ESTOC Range. Estoc Features. Electrical Supply. Product Code. Sizes 355, 400, 450, 500, 560, 630 and 710.

Square Duct Fans - ESTOC Range. Estoc Features. Electrical Supply. Product Code. Sizes 355, 400, 450, 500, 560, 630 and 710. Square Duct Fans - ESTOC Range Features Sizes from 355 to 71 mm diameter Air flow 1,9 m 3 /h (5.2 m 3 /s) Static pressures up to 115 Pa Maximum temperature from +4 C to +7` C (depending on the model) Adjustable

More information

TGT Series Adjustable Pitch Fans

TGT Series Adjustable Pitch Fans CYLINDRICAL CASED AXIAL FLOW FANS Series Adjustable Pitch Fans Range of adjustable pitch aerofoil blade, cased axial flow fans.casings formed from rolled sheet steel with a corrosion resistant hot dipped

More information

CYLINDRICAL CASED AXIAL FLOW FANS TGT Series - ADJUSTABLE PITCH FANS

CYLINDRICAL CASED AXIAL FLOW FANS TGT Series - ADJUSTABLE PITCH FANS - ADJUSTABLE PITCH FANS Range of adjustable pitch aerofoil blade, cased axial flow fans. Casings formed from rolled sheet steel with a corrosion resistant hot dip galvanised finish. All models incorporate

More information

Max. airflow m 3 /s Diam. min. Diam. max

Max. airflow m 3 /s Diam. min. Diam. max Axial Fans Max. airflow m 3 /s Diam. min Diam. max 1% adjustable motor Assembly, any position Reversible (3% Reduction) Page Number AW AR AW.97 2 3 * * 13 AR.97 2 3 * * 134 ZSP 2.9 315 5 * * 13 ZAP 13.89

More information

ErP METAL TUBE FANS - ROPERA EC FEATURES ELECTRICAL SUPPLY TEMPERATURE RANGE SIZES FEATURES AND CONSTRUCTION PRODUCT CODE INSTALLATION

ErP METAL TUBE FANS - ROPERA EC FEATURES ELECTRICAL SUPPLY TEMPERATURE RANGE SIZES FEATURES AND CONSTRUCTION PRODUCT CODE INSTALLATION 95 METAL TUBE FANS - ROPERA EC FEATURES mm to 355 mm diameter Air flow up to.56 m 3 /s Static pressures up to 7 Pa Casing - galvanized sheet steel Backward curved impeller Easy electrical connection via

More information

Vent-Axia Sabre Sickle Roof Fans (VSR)

Vent-Axia Sabre Sickle Roof Fans (VSR) Vent-Axia Sabre Sickle Roof Fans (VSR) Features and Benefits High performance roof sickle fan Fully assembled cowl. Optional backdraught shutters and birdguard Moulded from recyclable polymeric material,

More information

CONTENTS. Page. Adjustable Axial Pitch Flow Fans 3. Dimensions 4. AP056 Performance Curves 5. AP056 Sound Performance 6. AP063 Performance Curves 7

CONTENTS. Page. Adjustable Axial Pitch Flow Fans 3. Dimensions 4. AP056 Performance Curves 5. AP056 Sound Performance 6. AP063 Performance Curves 7 CONTENTS Page Adjustable Axial Pitch Flow Fans 3 Dimensions 4 AP056 Performance Curves 5 AP056 Sound Performance 6 AP063 Performance Curves 7 AP063 Sound Performance 8 AP071Performance Curves 9 AP071 Sound

More information

Performance. Sound Levels. Impellers. Motors. Accessories

Performance. Sound Levels. Impellers. Motors. Accessories EuroSeries (ESP) Die cast aluminium impellers Fully speed controllable Air Volumes up to 13.89m 3 /s Sizes 250 to 1000 dia protected to IP54 Operating Temperatures from -40 C up to +70 C Insulation Class

More information

Series TDA DIRECT DRIVEN MODEL: TDA- 450/9AA/8-8/ / Construction. Airflow Direction

Series TDA DIRECT DRIVEN MODEL: TDA- 450/9AA/8-8/ / Construction. Airflow Direction DIRECT DRIVEN Series TDA Construction Double flanged casing is produced in mild steel or galvanised steel, available in short and long cased. The impeller having manually adjustable pitch blades is made

More information

CENTRIFUGAL DIRECT DRIVE FANS CMT-CMB

CENTRIFUGAL DIRECT DRIVE FANS CMT-CMB CENTRIFUGAL DIRECT DRIVE FANS CMT-CMB Applications The CMT-CMB range of fans are suitable for many general and OEM ventilation applications where the extract of nonhazardous heated air is required. The

More information

Shut-off dampers. Type AK-Ex. For low-leakage shut-off of volume flows in potentially. explosive atmospheres (ATEX) PD AK-Ex 1.

Shut-off dampers. Type AK-Ex. For low-leakage shut-off of volume flows in potentially. explosive atmospheres (ATEX) PD AK-Ex 1. X X testregistrierung Shut-off dampers Type ATEX-compliant parts and units For low-leakage shut-off of volume flows in potentially explosive atmospheres (ATEX) Circular shut-off dampers for shutting off

More information

ROOFMASTER STEF-HT ROOF FAN

ROOFMASTER STEF-HT ROOF FAN fire safety Air movement Roof Fans ROOFMASTER STEF-HT ROOF FAN» Technical CATALOGuE Contents ROOFMASTER STEF-HT...3 Performance Data...4 Performance Table...5 General description...6 Fan Chart-explanation

More information

REVOLUTION SLCX Product Brochure

REVOLUTION SLCX Product Brochure REVOLUTION SLCX Brochure Available for next day delivery with ELTA SELECT ATEX Long Cased Axial Flow Fan For full detailed information on the following: Sound Data, Accessories & Wiring Data and Optimum

More information

Short casing. Long casing (L version) Highly versatile range due to different number of available blades and adjustable pitch angles

Short casing. Long casing (L version) Highly versatile range due to different number of available blades and adjustable pitch angles CYLINDRICAL CASED AXIAL FLOW FANS TGT Series Additional Information Standard air direction: form (B) configuration (Impeller over ). models description: incorporated an "L" after blade pitch angle. E.g.

More information

ROOFMASTER STEF-HT ROOF FAN

ROOFMASTER STEF-HT ROOF FAN fire safety Air movement Roof Fans ROOFMASTER STEF-HT ROOF FAN» Technical CATALOGuE Contents ROOFMASTER STEF-HT...3 Performance Data...4 Performance Table...5 General description...6 Fan Chart-explanation

More information

TURBOFLOW TF Contra Rotating Axial Flow Fan

TURBOFLOW TF Contra Rotating Axial Flow Fan TURBOFLOW TF Contra Rotating Axial Flow Fan Select models available for next day delivery TURBOFLOW TF Overview 5 standard sizes from 450mm to 630mm Air volume flow rates up to 4.6 m³/s Static pressures

More information

Tube Fans - ROPERA Range ROPERA 100 (L) Features. Electrical Supply. Product Code. Sizes 100, 125, 150, 160, 200, 250, 315 and 355.

Tube Fans - ROPERA Range ROPERA 100 (L) Features. Electrical Supply. Product Code. Sizes 100, 125, 150, 160, 200, 250, 315 and 355. Tube Fans - ROPERA Range Features 1 mm to 355 mm diameter Air flow 234 m 3 /h (.65 m 3 /s) Static pressures up to 92 Pa Casing - galvanized sheet steel Backward curved impeller Easy electrical connection

More information

ROOF MOUNTED AXIAL FLOW FANS HCTB / HCTT Series

ROOF MOUNTED AXIAL FLOW FANS HCTB / HCTT Series asy to install Supports to facilitate installation in the roof. XTRACTION (type B) SUPPLY (type A) High quality steel sleeve nsuring the long life of the fan. Range of axial roof fans with horizontal air

More information

Eco Mixed Flow (emf) Energy Saver. Terminal Box. Performance. Quality Assurance. Impellers. Accessories. Motors

Eco Mixed Flow (emf) Energy Saver. Terminal Box. Performance. Quality Assurance. Impellers. Accessories. Motors Eco Mixed Flow (emf) High efficiency Mixed Flow Fan with guide vanes Available in sizes 355 to 710mm dia. IP54 Fan rating (duct mounted) Operating temperatures up to 80 C (see technical specification)

More information

ROOFMASTER STEF-ATEX ROOF FAN

ROOFMASTER STEF-ATEX ROOF FAN Air Comfort Air movement Roof fans ROOFMASTER STEF-ATEX ROOF FAN» Technical CATALOGuE 2 STEF-ATEX Roofmaster - Technical Catalogue Contents General description Application/specification... 3 Features...

More information

Square Mixed Flow Fans (MFQ)

Square Mixed Flow Fans (MFQ) Square Mixed Flow Fans (MFQ) Features and Benefits Motors protected to IP44 Motor insulation Class B Maximum operating temperature +40 C Standard Thermal Overload Protection Sizes 400 to 500 3 phase are

More information

CAV controllers. Type EN-Ex. For the precise control of normal and high constant volume flows in potentially explosive atmospheres (ATEX)

CAV controllers. Type EN-Ex. For the precise control of normal and high constant volume flows in potentially explosive atmospheres (ATEX) X X testregistrierung CAV controllers Type Adjustment scale For the precise control of normal and high constant volume flows in potentially explosive atmospheres (ATEX) Rectangular, mechanical self-powered

More information

Square Duct Fans - ESTOC TARGE Range. Estoc Targe Features. Electrical Supply. Sizes 355, 400, 450, 500, 560 and 630.

Square Duct Fans - ESTOC TARGE Range. Estoc Targe Features. Electrical Supply. Sizes 355, 400, 450, 500, 560 and 630. Square Duct Fans - ESTOC TARGE Range Features Sizes from 55 to 6 mm diameter Air flow 21, m /h (5.8 m /s) Static pressures up to 145 Pa Maximum temperature up to 11 C Controllable external rotor motors

More information

HIGH TEMPERATURE TWIN SQUIF FANS

HIGH TEMPERATURE TWIN SQUIF FANS HIGH TEMPERATURE FANS HIGH TEMPERATURE FOR SMOKE EXTRACT CERTIFIED TO EN12101-3-2002. 374 029 2085 8200 BENEFITS QUIET AND POWERFUL SOLUTIONS High performance centrifugal motor/impeller combination providing

More information

Axial-flow Fan AFC. Model numbering system AF C / T. Accessories Three phase. Power rate 1.

Axial-flow Fan AFC. Model numbering system AF C / T. Accessories Three phase. Power rate 1. xial-flow Fan FC Construction xial fan designed for installation in a ducted system. Casing of rolled and electro-welded steel sheet, powder coated RL5. Impeller in polypropylene. Casing in acid-proof

More information

AXICIAT VA. Axial fans. Smoke extraction F200/120 and F400/120. High available pressure

AXICIAT VA. Axial fans. Smoke extraction F200/120 and F400/120. High available pressure Smoke extraction F200/120 and F400/120 A complete range from 1250 to 95000 m 3 /s High available pressure Blade with variable pitch on stop APPLICATION Extraction or introduction of non-loaded air in the

More information

Circular Box Fans - DAISHO EC Range DAISHO EC 125. Features. Electrical Supply. Product Code. Sizes 125, 150, 200, 250, 315, 450, 630 and 1000.

Circular Box Fans - DAISHO EC Range DAISHO EC 125. Features. Electrical Supply. Product Code. Sizes 125, 150, 200, 250, 315, 450, 630 and 1000. Circular Box Fans - DAISHO EC Range Features 125mm to 1mm Air flow 1,25 m 3 /h (3.5m 3 /s) Static pressures up to 125 Pa Maximum temperature range 6ºC Suitable for variable or constant pressure systems

More information

Powerful centrifugal fans for universal use: The product ranges TEM and REM

Powerful centrifugal fans for universal use: The product ranges TEM and REM Powerful centrifugal fans for universal use: The product ranges TEM and REM The fan ranges TEM and REM offered by Nicotra Gebhardt do present a large fan programme of single inlet centrifugal fans which

More information

CONTINUO. Radial centrifugal impeller. Radial centrifugal impellers dynamically balanced, according to ISO 1940 standard,

CONTINUO. Radial centrifugal impeller. Radial centrifugal impellers dynamically balanced, according to ISO 1940 standard, RADIAL CENTRIFUGAL FANS CBT-N Series CONTINUO Range of single inlet direct driven centrifugal fans designed for the continuous extraction of air stream up to 120ºC(1). The casings are manufactured from

More information

hore PRODUCT CATALOGUE nd Offsh arine an ms for Ma & Refrig CENTRIFUGAL FANS HV VAC &

hore PRODUCT CATALOGUE nd Offsh arine an ms for Ma & Refrig CENTRIFUGAL FANS HV VAC & hore nd Offsh arine an ms for Ma geration System & Refrig HV VAC & PRODUCT CATALOGUE CENTRIFUGAL FANS ! "# $ % & " ' (! ) * +,+( -../01..2 PRODUCT CATALOGUE 73-16 CENTRIFUGAL FANS CONTENT PAGE 1. CENTRIFUGAL

More information

CGT Series Adjustable Pitch Fans

CGT Series Adjustable Pitch Fans AXIAL FLOW CABINET FAN CGT Series Adjustable Pitch Fans New Ø 400-450-500 Range of adjustable pitch aerofoil blade, axial flow cabinet fans.fan casing manufactured from heavy gauge galvanised sheet steel

More information

Tube Fans - ESPADA Range ESPADA 100 (L) Features. Electrical Supply. Product Code. Sizes 100, 125, 150, 160, 200, 250 and 315

Tube Fans - ESPADA Range ESPADA 100 (L) Features. Electrical Supply. Product Code. Sizes 100, 125, 150, 160, 200, 250 and 315 Tube Fans - ESPADA Range Features mm to 315 mm diameter Air flow 18 m 3 /h (.5 m 3 /s) Static pressures up to 72 Pa Plastic cased centriugal fan Low noise levels Completely corrosion resistant Easy electrical

More information

LC/SC. Long & Short Cased Axial Fans

LC/SC. Long & Short Cased Axial Fans LC/SC Long & Short Cased xial Fans LC/SC contents introduction features & benefits specification performance dimensional data mounting silencer data accessories inverters & DCV controllers additional

More information

IN-LINE DUCT FANS MIXVENT-TD Fan Systems

IN-LINE DUCT FANS MIXVENT-TD Fan Systems IN-LINE DUCT FANS MIXVENT-TD Fan Systems NEW TD-EXTRACTOR KIT (see page 175) MIXVENT TD / MIXVENT TD-T MIXVENT TDx2 ACCESSORIES Description Range Construction The MIXVENT system has been designed to compliment

More information

CONTRA ROTATING CASED AXIAL FANS TCBBx2 / TCBTx2 Series

CONTRA ROTATING CASED AXIAL FANS TCBBx2 / TCBTx2 Series Range of cylindrical cased axial fans fitted with aluminium impellers and manufactured from high grade rolled galvanised steel and protected against corrosion by cataforesis primer and black polyester

More information

NOVENCO FAN CATALOGUE

NOVENCO FAN CATALOGUE NOVENCO FAN CATALOGUE WWW.NOVENCO-MARINE.COM ZERAX AXIAL FLOW FANS PRODUCT The Novenco ZerAx series of axial flow fans use innovative design to reduce power consumption and to better fan efficiency. The

More information

CGT Series Adjustable Pitch Fans

CGT Series Adjustable Pitch Fans AXIAL FLOW CABINET FAN CGT Series Adjustable Pitch Fans New Ø 400-450-500 Range of adjustable pitch aerofoil blade, axial flow cabinet fans.fan casing manufactured from heavy gauge galvanised sheet steel

More information

Type AK-Ex FOR LOW-LEAKAGE SHUT-OFF OF VOLUME FLOWS IN POTENTIALLY EXPLOSIVE ATMOSPHERES (ATEX)

Type AK-Ex FOR LOW-LEAKAGE SHUT-OFF OF VOLUME FLOWS IN POTENTIALLY EXPLOSIVE ATMOSPHERES (ATEX) Homepage > Products > Control units > Shut-off and restriction > Shut-Off Devices > Type AK-Ex Type AK-Ex FOR LOW-LEAKAGE SHUT-OFF OF VOLUME FLOWS IN POTENTIALLY EXPLOSIVE ATMOSPHERES (ATEX) Circular shut-off

More information

Terminal Box Are to IP54, as standard, protected against dust and water from any angle allowing outside applications.

Terminal Box Are to IP54, as standard, protected against dust and water from any angle allowing outside applications. EuroSeries (ESR) Cowl & base moulded from recyclable polymeric material All sizes resistant to UV light Sizes 250 to 1000 dia are protected to IP54 Optional backdraught shutters and bird guard (250-630mm)

More information

AC Commercial Fans Edition. ErP ready

AC Commercial Fans Edition. ErP ready AC Commercial Fans 213 Edition ErP ready AC Commercial Fans Axair Fans UK Ltd / 1782 34943 About Axair Fans UK Axair is an independent industrial fan manufacturer and distributor. What we offer : Application

More information

CAV controllers. Type RN-Ex. For the precise control of constant volume flows in potentially explosive atmospheres (ATEX) PD RN-Ex 1

CAV controllers. Type RN-Ex. For the precise control of constant volume flows in potentially explosive atmospheres (ATEX) PD RN-Ex 1 X X testregistrierung CAV controllers Type Adjustment scale ATEX-Zertifizierung For the precise control of constant volume flows in potentially explosive atmospheres (ATEX) Circular, mechanical self-powered

More information

Mixed Flow Roof Fans (RMH)

Mixed Flow Roof Fans (RMH) Mixed Flow Roof Fans (RMH) Features and Benefits Motors protected to IP44 Motor insulation Class B Maximum operating temperature 4 C Standard Thermal Overload Protection IP65 P65 service isolator Guard

More information

MegaBox Product-specific information

MegaBox Product-specific information MegaBox Product-specific information Application Noise-encapsulating centrifugal fans with retractable motor impeller unit and motor located outside the air flow Suitable for rough operating conditions

More information

Powerful centrifugal fans for universal use: The product ranges TEM and REM

Powerful centrifugal fans for universal use: The product ranges TEM and REM Powerful centrifugal fans for universal use: The product ranges TEM and REM The fan ranges TEM and REM offered by Nicotra Gebhardt do present a large fan programme of single inlet centrifugal fans which

More information

Specifications. Applications Ventilation of safety cabinets (STORM 10), scrubbers, fume capture arms, filter housing, etc. (STORM 12, 14, 16).

Specifications. Applications Ventilation of safety cabinets (STORM 10), scrubbers, fume capture arms, filter housing, etc. (STORM 12, 14, 16). Specifications Applications Ventilation of safety cabinets (STORM 10), scrubbers, fume capture arms, filter housing, etc. (STORM 12, 14, 16). Housings: PP* Single block strong high density UV treated and

More information

Utility Sets Standard Design Features Standard design features common to all Class I and Class II fans

Utility Sets Standard Design Features Standard design features common to all Class I and Class II fans Standard Design Features Utility Sets Standard Design Features Standard design features common to all Class I and Class II fans Shaft AISI 1045, turned ground and polished for accuracy. Designed to provide

More information

Mixed Flow Roof Fans (RMH)

Mixed Flow Roof Fans (RMH) Mixed Flow Roof Fans (RMH) Motors protected to IP44 Motor insulation Class B Maximum operating temperature 4 C Standard Thermal Overload Protection IP65 service isolator Bird guard included as standard

More information

Novenco axial flow fans. ZerAx - Standard January 2010

Novenco axial flow fans. ZerAx - Standard January 2010 Novenco axial flow fans ZerAx - Standard January 2010 Product facts Product The Novenco ZerAx series of axial flow fans uses innovative design to reduce power consumption by improving efficiency. As an

More information

AXIAL FANS & VANEAXIAL FANS

AXIAL FANS & VANEAXIAL FANS AXIAL FANS & VANEAXIAL FANS TYPE MPV APPLICATIONS Typical application for this fan is mechanical ventilation of cargo rooms, engine room a.o. Where you have transportation of big air volumes at relative

More information

SLCX ATEX LONG CASED AXIAL FLOW FAN PLEASE CONTACT AERAULIQA DIRECLTY FOR A SPECIFIC FAN SELECTION ACCESSORIES APPLICATION FEATURES & BENEFITS

SLCX ATEX LONG CASED AXIAL FLOW FAN PLEASE CONTACT AERAULIQA DIRECLTY FOR A SPECIFIC FAN SELECTION ACCESSORIES APPLICATION FEATURES & BENEFITS ATEX LOG ASE AXAL FLOW FA ALATO ATEX ucted Axial Flow Fans suitable to exhaust/supply air in presence of chemical processes, water and sewage treatment, material and gas waste, dust and paint extraction,

More information

TCDH F400-TCDV F400. Smoke extract - Fire protection SMOKE EXTRACT FANS CENTRIFUGAL BACKWARD ROOF FANS F Application. Range.

TCDH F400-TCDV F400. Smoke extract - Fire protection SMOKE EXTRACT FANS CENTRIFUGAL BACKWARD ROOF FANS F Application. Range. N OU VE A U Approved F400 10 (400 C 10 mn) CE marked Special range for speed variation VAR Easy installation and maintenance Low sound level Electrical accessories and relay box mounted wired New vertical

More information

Roof Units. Specification. Construction. Performance. Impellers. Size range. Ancillary Equipment

Roof Units. Specification. Construction. Performance. Impellers. Size range. Ancillary Equipment Roof Extract Units Roof Units Specification The Flaktwoods Colchester range of roof extract units are designed to satisfy the consultants functional requirement for a direct drive fan unit of guaranteed

More information

Medium Pressure Centrifugal Fans

Medium Pressure Centrifugal Fans Medium Pressure Centrifugal Fans 2012 Edition ...About Axair Fans UK Application Knowledge: Over 20 years experience in general air movement; including corrosive, explosive and hot fume handling. Stock

More information

CMB / CMT Series CENTRIFUGAL SINGLE INLET FANS. Centrifugal direct drive fans CMB/CMT 80 C. Impeller dynamically balanced

CMB / CMT Series CENTRIFUGAL SINGLE INLET FANS. Centrifugal direct drive fans CMB/CMT 80 C. Impeller dynamically balanced CENTRIFUGAL SINGLE INLET FANS CMB / CMT Series 80 C CONTINUOUS operation Range of centrifugal single inlet fans suitable for continuous extraction of airstreams temperature up to 80ºC (Series 1) or 150ºC

More information

400ºC/2h centrifugal roof fans with horizontal or vertical air outlet CHT 200 4T BS. Installed capacity

400ºC/2h centrifugal roof fans with horizontal or vertical air outlet CHT 200 4T BS. Installed capacity 400ºC/2h centrifugal roof fans with horizontal or vertical air outlet : 400ºC/2h centrifugal roof fans with horizontal air outlet, hood in aluminium : 400ºC/2h centrifugal roof fans with vertical air outlet,

More information

BIFURCATED AXIAL FANS

BIFURCATED AXIAL FANS BFURATE AXAL FAS SB (YL) ALATO SB (O) Bifurcated axial fans suitable to move air in hostile applications, for example in case of dust and chemical substances in heavy industrial, boiler houses, corrosive

More information

HEAVY DUTY FANS FOR INDUSTRIAL APPLICATIONS

HEAVY DUTY FANS FOR INDUSTRIAL APPLICATIONS HEAVY DUTY FANS FOR INDUSTRIAL APPLICATIONS OUR COMMITMENT TO THE ENVIRONMENT Sodeca has begun a new stage of study and design of new trends in ventilation which will help to preserve the environment and

More information

Series VENTS OVK. Low pressure axial fans in the steel casing with the air capacity up to m 3 /h for wall mounting

Series VENTS OVK. Low pressure axial fans in the steel casing with the air capacity up to m 3 /h for wall mounting AXIAL FANS Series VENTS OV Series VENTS OVK Series VENTS Low pressure axial fans in the steel casing with the air capacity up to 122 m 3 /h for wall mounting Low pressure axial fans in the steel casing

More information

A X I A L A N D C E N T R I F U G A L F A N S A N D B L O W E R S F O R A L L I N D U S T R I E S

A X I A L A N D C E N T R I F U G A L F A N S A N D B L O W E R S F O R A L L I N D U S T R I E S A X I A L A N D C E N T R I F U G A L F A N S A N D B L O W E R S F O R A L L I N D U S T R I E S Australia s leading fan company PRODUCT OVERVIEW COMMERCIAL INDUSTRIAL POWER & ENERGY MINING FOOD PROCESSING

More information

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733 SH Series 60 Hz SERIE SH HYDRAULIC PERFORMANCE RANGE AT 60 Hz WEB 10-2006 2 CONTENTS 5 Specifications... 6

More information

CHMT Series, F Rated Fans

CHMT Series, F Rated Fans CNTRIFUGAL SINGL INLT FANS CT Series, F400 120 Rated Fans Officially approved to N12101-3 standard (certificate number 0370-CPD-0348) Range of single inlet direct drive centrifugal fans designed for smoke

More information

NCF fans 50 Hz. Protection class IP 55

NCF fans 50 Hz. Protection class IP 55 The Nederman NCF Fans have direct drive motors which means a safe and cost effective operation. Installing an energy efficient NCF fan with our other Nederman products saves time and reduces energy costs.

More information

Category 1 (zone 0) covers areas, where there is a permanent or long lasting occurrence

Category 1 (zone 0) covers areas, where there is a permanent or long lasting occurrence Explosion proof fans General Systemair explosion proof fans have been developed to be used in effective supply and exhaust air systems allocated to category 2 (zone 1) and category 3 (zone 2) in explosion

More information

BULLETIN 456. July 1997 VANEAXIAL FANS. Type W Direct Drive/Belt Driven. Model VW Direct Drive. Model VWBD Belt Driven

BULLETIN 456. July 1997 VANEAXIAL FANS. Type W Direct Drive/Belt Driven. Model VW Direct Drive. Model VWBD Belt Driven BULLETIN 456 July 1997 VANEAXIAL FANS Type W Direct Drive/Belt Driven Model VW Direct Drive Model VWBD Belt Driven Aerovent certifies that the Type W Vaneaxial Fans shown herein are licensed to bear the

More information

NEW Slimpak EC Box Fan (SLPT EC)

NEW Slimpak EC Box Fan (SLPT EC) NEW Slimpak EC Box Fan (SLPT EC) Compact low profile design Duct Sizes 100 500mm Performance - Airflow 0.01 to 1.2m 3 /s, Pressure up to 650Pa Latest energy saving EC/DC motors Internal mounting IPX2 Manufactured

More information

Series VENTS KSK. Centrifugal kitchen fan in sound-insulated casing with air flow up to 8138 m 3 /h

Series VENTS KSK. Centrifugal kitchen fan in sound-insulated casing with air flow up to 8138 m 3 /h SOUND-INSULATED KITCHEN FAN Series device. The impeller is mounted on the motor shaft and is balanced statically and dynamically. The motor has F class motor winding insulation and ingress protection rating.

More information

SECTION AXIAL HVAC FANS

SECTION AXIAL HVAC FANS SECTION 233413 - AXIAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Centrifugal medium-pressure fans fitted with multi-blade

Centrifugal medium-pressure fans fitted with multi-blade CMP/ATEX CMP/ATEX impeller Centrifugal medium-pressure fans fitted with multi-blade with ATEX certification Centrifugal single-inlet, medium-pressure fans with casing and sheet steel impeller to work in

More information