VIKING SG SERIES SEALLESS MAG DRIVE PUMPS
|
|
- Barrie Poole
- 6 years ago
- Views:
Transcription
1 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page OPERATING RANGE: SG Pumps (Cast Iron Mag Drive) and SGN (Ductile Iron Mag Drive) Displacements No. 23 SG and 7 SGN 0.06 to 90 (SG) and GPM 0.7 to 32 (SGN) Flow Range 0.03 to 43 (SG) and M 3 /Hr 0.6 to 7.2 (SGN) Pressure Range Temperature Range Viscosity Range PSI to 500 Continuous Bar to 34 Continuous F -40 to 500 C -40 to 260 SSU 2 to 250,000 cst to 55,000 Where shaft seal leakage is not allowable, for liquids that are hard to seal, or where seal maintenance is difficult, Viking Mag Drive sealless SG pumps are the solution. In this type of pump, a canister hermetically seals the liquid within the pump. Inner magnets are connected to the pump drive shaft inside the canister, and an outer magnet assembly rotates outside of the canister, driven by a motor or other drive, so that magnetic forces pass through the canister to the inner magnets and cause the drive shaft to rotate. This eliminates traditional dynamic shaft seals, and problems associated with them (wear, leakage, air infiltration). A hollow drive shaft allows some liquid to flow by means of pressure differential from the high pressure side of the pump through the shaft, into the canister and back to the low pressure side of the pump. This provides magnet cooling and prevents product stagnation. TYPICAL APPLICATIONS: Fuels and Additives Polyurethane Meter / Mix Adhesive & Sealant Dispensing Pipeline Sampling Chemical Metering Heat Transfer Oils VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
2 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) MATERIALS OF CONSTRUCTION - ALL SERIES Component Standard - SG-04, -05, -07 Standard - SGN-05, -07 Standard - SG-0, -4 Options Casing, Bracket, Head, Separation Plate Relief Valve Body Cast Iron ASTM A23 Cast Iron ASTM A23 Ductile Iron ASTM A536 Ductile Iron ASTM A536 Relief Valve Poppet Hardened Steel Hardened Steel Relief Valve Spring Steel ASTM A229 Steel ASTM A229 Cast Iron ASTM A23 Cast Iron ASTM A4 Ductile Iron ASTM A536 Chrome Silicon Spring Steel ASTM A40 Gears Hardened Steel Hardened Steel Hardened Steel Shafts Case-Hardened Steel ASTM A322 Case-Hardened Steel ASTM A322 Case-Hardened Steel ASTM A322 Surface Hardening (Vitek) PPS (composite) SG-07 only Nitralloy Anti-Friction Needle Bearings Bearing Steel Sleeve Bearings Carbon Graphite Carbon Graphite Carbon Graphite Silicon Carbide O-Rings Buna-N Buna-N Buna-N Neoprene, Viton, PTFE, Kalrez Canister 36L Stainless Steel 36L Stainless Steel 36L Stainless Steel Alloy C Magnetic Coupling Bracket (not wetted) Cast Iron ASTM A23 Cast Iron ASTM A23 Cast Iron ASTM A23 Aluminum SG-04,-05,-07 only Magnets (outer magnets nickel plated, inner magnets sealed in SS canister) Neodymium Iron Boron Neodymium Iron Boron Neodymium Iron Boron 2 Samarium Cobalt Maximum temperature 225 F / 07 C. 2 Maximum temperature 500 F / 260 C. MODEL NUMBER KEY SGN M 0 V Spur Gear Principle Frame Size Pump Size Design Series Material of Construction: Blank = Cast Iron N = Ductile Iron (-05,-07) Seal Type: = Mag Drive NOTE: Direction of rotation: clockwise is standard, counter-clockwise is optional. Bi-rotational is not available as Mag Drive. NOTE: Mag Drive pumps are connected to a magnetic coupling, which is specified separately. Coupling options are MD-A and MD-B (SG-04,-05,-07), MD2-B (SG-0) or MD2-C (SG-4). Specify NEMA or IEC face mount for close-coupled or bearing carrier for long-coupled. See page to determine the correct coupling. Shaft Rotation: (Viewed from shaft end) 0 = Clockwise = Counter- Clockwise (optional) Relief Valve: O = Without Valve V = With Valve Viton and Kalrez are registered trademarks of DuPont Performance Elastomers VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
3 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page SPECIFICATIONS SERIES SG-04, SG-05, SG-07, SG-0, SG-4 (CAST IRON) - SGN-05, SGN-07 (DUCTILE IRON) Model Numbers Port Size 60 Hz Motor Speed Nominal Pump Rating 50 Hz Motor Speed Maximum Continuous Pressure 2 Magnetic Coupling Availability Torque Maximum Hydrostatic Pressure Approximate Shipping Weight Pump With Valve (Less Power) Approximate Coupling Only Shipping Weight (ready to accept but less power) Cast Iron Ductile Iron Inches GPM RPM M 3 /Hr RPM PSI Bar Series Ft-Lbs Nm PSIG Bar Lbs KG Lbs KG SG SG SG MD-A SG SG SG SG-05 SGN SG-0525 SGN SG-0535 SGN SG-0550 SGN SG-0570 SGN MD-A SG-050 SGN SG-054 SGN-054 ¾ SG-059 SGN-059 ¾ SG-052 SGN-052 ¾ SG-074 SGN SG 075 SGN SG-072 SGN MD-A SG-07 SGN SG-076 SGN MD-B SG-0722 SGN-0722 x ¼ SG-0732 SGN-0732 x ¼ SG SG MD2-B SG SG SG MD2-C SG NOTE: Maximum temperature (standard construction) 225 F, 07 C. Higher temperatures can be handled with Samarium Cobalt magnets and optional O-ring elastomers. See page for torque and temperature limits. Optional high pressure canisters available. Consult factory. 2 See page for Selecting the correct Mag Drive coupling. 3 NPT standard. Consult factory for other port size or type options such as BSP, SAE O-Ring or other. 4 SAE J5 Code 6 flange with metric threaded fastener holes standard. Consult factory for other port sizes or type options such as NPT, BSP, SAE O-Ring or other. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200 Metric conversions are based on US measurements.
4 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) SELECTING THE CORRECT VIKING MAG DRIVE COUPLING With any mag drive pump, the magnetic forces between the inner and outer magnets must meet or exceed the torque generated by the drive at the application s peak flow, speed and pressure, or the magnets will decouple, which can cause permanent loss of magnetic attraction. Instead of offering mag drive pumps with just one torque rating, Viking allows you to select between several magnetic couplings with different torque ratings. This ensures enough torque for the application, but keeps costs down by using only as much torque as is needed. Viking also offers two magnet materials in each of the coupling sizes. The standard Neodymium magnets are lowest cost, but are limited in temperature to 225 F (07 C). The optional Samarium Cobalt magnets range up to 500 F (260 C). Specify magnet material when ordering. Selecting the Right Coupling. Find pump HP and speed from performance curves using the Pump Selector program on 2. Calculate application torque (T), using this formula: T (FT LB) = HP/SPEED x Select temperature correction factor (TCF) from Table or Table Divide the calculated application torque (T) by the temperature correction factor (TCF) to get the Adjusted Application Torque. 5. Select the coupling with a torque rating (from Table 3) equal to or greater than the Adjusted Application Torque (AAT). Viking couplings have a built-in service factor, so if you have calculated the AAT correctly, you can be comfortable with a coupling that is equal to your calculated torque. Application Temp. ( F) Application Temp. ( C) Temperature Correction Factors for Standard Neodymium Magnets TC Factor Application Temp. ( F) Application Temp. ( C) Temperature Correction Factors for Optional Samarium Cobalt Magnets TC Factor TABLE 2 Magnetic Coupling Torque Capacity Coupling Size Torque (FT-LBS) Nm MD-A MD-A MD-B MD-B MD2-B MD2-B MD2-B MD2-C MD2-C MD2-C MD2-C TABLE 3 Example :. An application calls for pumping GPM of 00 SSU (22 cst) liquid at 400 PSI (27 Bar), at 00 F (3 C), with a 750 RPM motor. From the Pump Selector program, an SG0525 is selected, providing 0.95 GPM (3.6 lpm) at 750 RPM, with 0.35 BHP (0.26 kw). 2. Calculate torque. T = 0.35 / 750 x 5252 = From Table, the TCF is AAT =.05 / 0.94 =.2 FT-LB. 5. Select MD-A4 coupling in standard Neodymium magnet material (4 FT-LB rating >.2 FT-LB Adjusted Application Torque) TABLE VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
5 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page DRIVE OPTIONS FOOT-BRACKET MOUNTED PUMPS ( B DRIVE) Series SG- pumps are available with a bearing carrier mounted to the magnetic coupling to provide an external drive shaft for long-coupling to a reducer, gear motor or other drive. The 3.5 shaft height on MD-A couplings matches the shaft height on Viking A series reducers, as well as NEMA 56, 43 and 45 T motors. The 6.25 shaft height on MD-B couplings matches shaft height on 254/256 T motors. The MD2-B coupling for SG-0 has 5.5 shaft height matching Viking B reducers. Dimensions for Foot-Bracket Mounted Pumps ( B Drive) See Pages MOTOR MOUNTED UNITS ( M DRIVE) Series SG-04, -05 & -07 pumps may be close coupled to NEMA-C faced motors and SG-0 & -4 to both NEMA-C and IEC B5 flanged motors to provide an easily-assembled, compact pumping unit. This mounting arrangement eliminates the need for on-site coupling alignment that is normally required for a basemounted unit. Dimensions for Motor Mounted Pumps ( M Drive) See Pages VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
6 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-04, SG-05 AND SGN-05 (MD-A_ B DRIVE) FOOT BRACKET MOUNT MODEL NO. SG-047MD-A_B SG-04MD-A_B SG-0425MD-A_B SG-0435MD-A_B SG-0450MD-A_B SG-0470MD-A_B SG-05MD-A_B SGN-05MD-A_B SG-0525MD-A_B SGN-0525MD-A_B SG-0535MD-A_B SGN-0535MD-A_B SG-0550MD-A_B SGN-0550MD-A_B SG-0570MD-A_B SGN-0570MD-A_B SG-050MD-A_B SGN-050MD-A_B SG-054MD-A_B SGN-054MD-A_B SG-059MD-A_B SGN-059MD-A_B SG-052MD-A_B SGN-052MD-A_B A ¾ ¾ ¾ WITH R/V LESS R/V B C E B C E DD in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
7 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ B DRIVE) FOOT BRACKET MOUNT WITH R/V LESS R/V MODEL NO. A B C E B C E SG-074MD-A_B SGN-074MD-A_B in mm SG-075MD-A_B SGN-075MD-A_B in mm SG-072MD-A_B SGN-072MD-A_B in mm SG-07MD-A_B SGN-07MD-A_B in mm SG-076MD-A_B SGN-076MD-A_B in mm SG-0722MD-A_B SGN-0722MD-A_B S ¼ D in mm SG-0732MD-A_B SGN-0732MD-A_B S ¼ D in mm S = Suction Port D = Discharge Port VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
8 Section 34.3 Page Issue B SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-07 AND SGN-07 (MD-B_ B DRIVE) FOOT BRACKET MOUNT WITH R/V LESS R/V MODEL NO. A B C E B C E SG-074MD-B_B SGN-074MD-B_B in mm SG-075MD-B_B SGN-075MD-B_B in mm SG-072MD-B_B SGN-072MD-B_B in mm SG-07MD-B_B SGN-07MD-B_B in mm SG-076MD-B_B SGN-076MD-B_B in mm SG-0722MD-B_B SGN-0722MD-B_B S ¼ D in mm SG-0732MD-B_B SGN-0732MD-B_B S ¼ D in mm S = Suction Port D = Discharge Port VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
9 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page Issue B DIMENSIONS SERIES SG-0 (MD2-B_ B DRIVE) & SERIES SG-4 (MD2-C_ B DRIVE) FOOT BRACKET MOUNT PUMP AB W N R S A-PORTS X Y L Z B SG (35.9) 2.06 (52.3) 0.5 (3.0).03 (26.2) M0.00" 6.42 (63.) SG (50.) 2.3 (54.).90 (4.3) 0.70 (7.) M2.50" 4.50 (4.3) 3.63 (92.2) 6.9 (77.3) 6.63 (6.4) 3 (76.2) SG (55.7) 2. (73.2).53 (3.9) 0.4 (2.3) M2 2.00" 7.20 (2.9) SG (54.9) 2.37 (60.2) 0.4 (2.3).53 (3.9) M2 2.00" 7.04 (7.) SG (72.7) 3.27 (3.).2 (30.7) 2.09 (53.) M6 3.00" 5.9 (3.) 3.63 (92.2) 7.74 (96.6) 7. (0.6) 4.5 (4.3) SG (2.6) 4. (24.0).53 (3.9) 2.56 (65.0) M6 4.00".3 (206.5) DIMENSIONS FOR "U" MODELS (in.) Coupling D E F G H J K M O P T U V AD AE MD2-B (SG-0) MD2-C (SG-4) DIMENSIONS FOR "M" MODELS (mm) Coupling D E F G H J K M O P T U V AD AE MD2-B (SG-0) MD2-C (SG-4) VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
10 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-04, SG-05 & SGN-05 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTLESS BRACKET NOTE: Footless bracket requires footed motor. MODEL NO. A WITH R/V LESS R/V B C B C MOTOR FRAME SIZE DD D E F H J MC SG-047MD-A_M SG-04MD-A_M SG-0425MD-A_M SG-0435MD-A_M SG-0450MD-A_M SG-0470MD-A_M SG-05MD-A_M SGN-05MD-A_M SG-0525MD-A_M SGN-0525MD-A_M SG-0535MD-A_M SGN-0535MD-A_M SG-0550MD-A_M SGN-0550MD-A_M SG-0570MD-A_M SGN-0570MD-A_M SG-050MD-A_M SGN-050MD-A_M SG-054MD-A_M SGN-054MD-A_M SG-059MD-A_M SGN-059MD-A_M SG-052MD-A_M SGN-052MD-A_M ¾ ¾ ¾ in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm C 43TC 45TC 2TC 4TC 23TC* SLOT * Motor shaft must be modified to resemble 2TC-4TC shaft length, diameter and key. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
11 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTLESS BRACKET NOTE: Footless bracket requires footed motor. See page for optional footed MD-A brackets. MODEL NO. A WITH R/V LESS R/V B C B C MOTOR FRAME SIZE D E F H J MC SG-074MD-A_M SGN-074MD-A_M in mm C SLOT SG-075MD-A_M SGN-075MD-A_M in mm TC SG-072MD-A_M SGN-072MD-A_M in mm TC SG-07MD-A_M SGN-07MD-A_M in mm TC SG-076MD-A_M SGN-076MD-A_M SG-0722MD-A_M SGN-0722MD-A_M S ¼D in mm in mm TC 23TC* SG-0732MD-A_M SGN-0732MD-A_M S ¼D in mm * Motor shaft must be modified to resemble 2TC-4TC shaft length, diameter and key. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
12 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTED BRACKET NOTE: Footed bracket requires footless motor. See pages for optional footless MD-A brackets. MODEL NO. SG-074MD-A_M SGN-074MD-A_M SG-075MD-A_M SGN-075MD-A_M A B WITH R/V C E B LESS R/V C E MOTOR FRAME SIZE in mm in mm SG-072MD-A_M SGN-072MD-A_M SG-07MD-A_M SGN-07MD-A_M SG-076MD-A_M SGN-076MD-A_M in mm in mm in mm C 43TC 45TC SG-0722MD-A_M SGN-0722MD-A_M S ¼D in mm SG-0732MD-A_M SGN-0732MD-A_M S ¼D in mm S = Suction Port D = Discharge Port Footed bracket is only available for up to NEMA 45TC frame motors (4.5 rabbet) - 0TC and 20TC motor frames with.5 rabbet are only available with footless bracket. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
13 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page DIMENSIONS SERIES SG-07 AND SGN-07 (MD-B_ M DRIVE) NEMA C MOTOR MOUNT FOOTED BRACKET NOTE: Footed bracket requires footless motor. No footless brackets available with MD-B couplings. MODEL NO. SG-074MD-B_M SGN-074MD-B_M SG-075MD-B_M SGN-075MD-B_M A B WITH R/V C E B LESS R/V C E MOTOR FRAME SIZE in mm in mm SG-072MD-B_M SGN-072MD-B_M SG-07MD-B_M SGN-07MD-B_M SG-076MD-B_M SGN-076MD-B_M in mm in mm in mm TC/4TC 23TC/25TC 254TC/256TC SG-0722MD-B_M SGN-0722MD-B_M S ¼D in mm SG-0732MD-B_M SGN-0732MD-B_M S ¼D in mm S = Suction Port D = Discharge Port Coupling will accept NEMA motor frames 2TC-256TC. NEMA 254TC-256TC will require shaft modification reducing shaft extension by ⅝. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
14 Section 34.3 Page SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-0 (MD2-B_ M DRIVE) & SERIES SG-4 (MD2-C_ M DRIVE) NEMA C AND IEC MOTOR MOUNT FOOTED BRACKET PUMP AB W N R S A-PORTS X Y L Z B SG (35.9) 2.06 (52.3) 0.5 (3.0).03 (26.2) M0.00" 6.42 (63.) SG (50.) 2.3 (54.).90 (4.3) 0.70 (7.) M2.50" 4.50 (4.3) 3.63 (92.2) 6.9 (77.3) 6.63 (6.4) 3 (76.2) SG (55.7) 2. (73.2).53 (3.9) 0.4 (2.3) M2 2.00" 7.20 (2.9) SG (54.9) 2.37 (60.2) 0.4 (2.3).53 (3.9) M2 2.00" 7.04 (7.) SG (72.7) 3.27 (3.).2 (30.7) 2.09 (53.) M6 3.00" 5.9 (3.) 3.63 (92.2) 7.74 (96.6) 7. (0.6) 4.5 (4.3) SG (2.6) 4. (24.0).53 (3.9) 2.56 (65.0) M6 4.00".3 (206.5) DIMENSIONS FOR "U" MODELS FOR NEMA C FACE MOTORS (in.) Coupling NEMA Drive D E F G H J O P AD MD2-B (SG-0) MD2-C (SG-4) 2/4TC /25TC /256TC thru 256TC /26TC DIMENSIONS FOR "M" MODELS FOR IEC B5 FLANGE MOTORS (mm) Requires unfooted motor. Coupling IEC Drive D E F G H J O P AD MD2-B (SG-0) MD2-C (SG-4) 00/ / VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
15 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page PERFORMANCE CURVE NOTES Printed performance curves are not available. Performance curves can be electronically generated with the Viking Pump Selector Program. This program can be located on for the general public. For authorized distributors, this program can be found listed under the Products tab at Security passwords are required to access IDEXconnect. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
VIKING SG SERIES SINGLE PUMPS (WITH SHAFT SEAL)
SERIES SG-04, -05, -07, -10, -14 () Page 341.1.1 OPERATING RANGE: SERIES SG-04/-05 PUMP SG Pumps (, Lip or Mechanical Sealed) Displacements No. 29 Flow Range Pressure Range Temperature Range Viscosity
More informationSPUR GEAR PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1451 Page 1451.
Page 1451.1 TABLE OF CONTENTS Features & Benefits...2 Typical Applications...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Component
More informationMOTOR SPEED PRODUCT LINE: CAST IRON MAG DRIVE PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
MOTOR SPEED PRODUCT LINE: SERIES 895 Section 1443 Page 1443.1 Issue B TBLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Key...3 Cutaway View & Pump Features...3 Specifications...4
More informationVIKING HG SERIES HELICAL GEAR EXTERNAL GEAR PUMPS
Page 350.1 Series Description Viking s HG series positive displacement pumps are designed to provide low noise transfer and processing of clean, lubricating liquids for applications such as lube oils,
More informationHigh Pressure, High Reliability
Viking SG Series External Gear Pumps High Pressure, High Reliability The SG Series External Gear Pumps are designed for reliability in industrial applications through an extensive range of sizes and options
More informationVIKING SPUR GEAR SINGLE PUMPS SERIES SG-04, SG-05, SG-07 AND SGN-05, SGN-07 STANDARD CONSTRUCTION FEATURES
VIKING SPUR GEAR SINGLE PUMPS FEATURES Section 34 Page 34. SERIES SG-04 and SG-05 Pumps Cutaway View.0 to.2 GPM Sizes (.0 to 2.5 m³/hr) SERIES SG-07 Pump Cutaway View 2.8 to 32.0 GPM Sizes (. to 7 m³/hr)
More informationHigh Pressure, High Reliability
Viking SG Series External Gear Pumps High Pressure, High Reliability The SG Series External Gear Pumps are designed to ensure reliability in industrial applications through an extensive range of sizes
More informationVIKING. Viking Mag Drive Series 855. Ideal for: Hard-to-Seal Liquids 24/7 Operations Hazardous and Toxic Liquids
Viking Mag Drive Series 855 VIKING Ideal for: Hard-to-Seal Liquids 24/7 Operations Hazardous and Toxic Liquids Capacity to 29.5 M 3 /Hr (130 GPM) Pressure to 14 Bar (200 PSI) Viscosity to 55,000 cst (250,000
More informationVIKING. Series LVP STAINLESS STEEL VANE PUMP. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 2016 PRODUCT DESCRIPTION SERIES OPERATING RANGE
Page 445.1 PRODUCT DESCRIPTION Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid through a cam-shaped
More informationProduct Range IDEX CORPORATION
Product Range IDEX CORPORATION Viking Pump provides an unmatched combination of application expertise and positive displacement pumping products to meet your pumping needs. We specialize in the design,
More informationSealless Mag Drive Pumps For Crucial Liquid Containment Applications
Viking Mag Drive Pumps Sealless Mag Drive Pumps For Crucial Liquid Containment Applications Eliminates pump seal maintenance Highest level of liquid containment available Metric or U.S. Design Sizes in
More informationLIQUID-SPECIFIC PRODUCT LINE: STAINLESS STEEL VANE PUMPS PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 NOMINAL FLOW RATES 2
Page 445.1 PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid
More informationMOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1442 Page 1442.
Page 1442.1 TABLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Specifications...2 Model Number Key...3 Cutaway View & Pump Features...3 Dimensions C, F, FH Sizes...4 Dimensions
More informationDuctile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A
Page 1601.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationUNIVERSAL PRODUCT LINE: DUCTILE IRON JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
Page 1602.1 TABLE OF CONTENTS Features & Benefits...2 Porting & Sealing...2 Jacketing...2 Revolvable Pump Casings...2 Cutaway View & Pump Features...3 Model Number Key...4 Standard Materials of Construction...4
More informationVIKING JACKETED ASPHALT PUMPS
VIKING ED ASPHALT PUMPS SERIES 34 AND 434 Section 430 Page 430.1 Issue G FEATURES 1 Pressure 1 Temperature 1 Viscosity 1 Flow To 100 PSI (6.9 Bar) -60 F. to +450 F. (-51 C. to +232 C.) 31 SSU to 250,000
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 4223, 4323 (API 682 Seal) Section 304 Page 304. TABLE OF CONTENTS Features & Benefits...2 Revolvable Pump Casings...2 Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4
More informationNominal Flow Pressure Range Temp. Range Viscosity Range
VIKING UNIVERSL XPD 676 PUMPS - FULL COMPLINCE with PI 676 STNDRDS SERIES 4223X & 4323X Section 633 Page 633.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps Offering Full Compliance with PI 676 Design Standards
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL NON-JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE:
Page 1701.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationVIKING UNIVERSAL SEAL PUMPS. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options. Operating Range1: Nominal Flow Rates:
VIKING UNIVERSAL SEAL PUMPS Section 630 Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Operating Range1: Cast Iron Series 124A/AE, 4124A/AE, 4124B, 324A, 4324A, 224A/AE,
More informationIndustrial Pump Catalog
Industrial Pump Catalog Contents Why Corken?........................................................................ i-5 About This Catalog...................................................................
More informationVIKING. Series LVP. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA Section 445 Page Issue C
VIKING Section 445 Page 445.1 Issue C PRODUCT DESCRIPTION Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping
More informationNominal Flow. Pressure Range. Temp. Range. Viscosity Range. Nominal Flow. Pressure Range. Temp. Range. Viscosity Range. Stainless Steel.
Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Standard Pump (shown: KK124A) Operating Range 1 : Cast Iron Series: 124A/AE, 4124A/AE, 324A, 4324A, 224A/AE, 4224A/AE
More informationVane Pumps for Corrosive, Thin Liquids at Higher Pressures
Viking LVP Series Stainless Steel Vane Pumps Vane Pumps for Corrosive, Thin Liquids at Higher Pressures Higher pressures than other stainless positive displacement pumps Low-wear, long-life vanes Superior
More informationUNIVERSAL PRODUCT LINE: CAST IRON NON-JACKETED PUMPS SERIES DESCRIPTION TABLE OF CONTENTS RELATED PRODUCTS OPERATING RANGE:
Page 1401.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features (124A/AE, 4124A/AE, 324A, 4324A)...4
More informationVane Pumps for Corrosive, Thin Liquids at Higher Pressures
Viking LVP Series Stainless Steel Vane Pumps Vane Pumps for Corrosive, Thin Liquids at Higher Pressures Capacity to 36 M³/Hr (160 GPM) Pressure to 14 Bar (200 PSI) Viscosity 0.1 to 500 cst (28 to 2,300
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
UNIVERSAL PRODUCT LINE: SERIES 227A, 4227A, 327A, 4327A Section 1702 Page 1702.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 223A, 4223A, 323A, 4323A Page 1302.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable Pump Casings...3 Cutaway View
More informationVIKING MOTOR SPEED INTERNAL GEAR PUMPS
VIKING MOTOR SPEED Series Description Vikg s Motor Speed series ternal gear pumps represent a technological advance the science of flow. Through new techniques of feedg the rotor and idler, Vikg has achieved
More informationSP SERIES SELF-PRIMING MAG DRIVE
SP SERIES SELF-PRIMING MAG DRIVE spend less time waiting. and more time pumping. year Big on power yet short on energy consumption, the SP Series from Finish Thompson is one of the most versatile and economical
More informationGENERAL OVERVIEW BRONZE PEDESTAL ROTARY GEAR N13HDM C992 BRONZE BRONZE HELICAL ROTOR 101BG RUBBER
GENERAL OVERVIEW BRONZE CLOSE COUPLED N970 BRONZE PEDESTAL N4000R BRONZE PEDESTAL ROTARY GEAR N13HDM PLASTIC CENTRIFUGAL 144 RUBBER ROLLER 310F BRONZE CENTRIFUGAL 50P DUCTILE IRON CLOSE COUPLED C992 BRONZE
More informationSealless, Non-Metallic Pumps for Crucial Liquid Containment Applications
Viking Non-Metallic Mag Drive Pumps Sealless, Non-Metallic Pumps for Crucial Liquid Containment Applications Universal flanges and Motor Adapters Standard housing mates to both DIN and ANSI flange systems
More informationPRODUCT OBSOLETED 1Q16
STANDARD CONSTRUCTION FEATURES Page 141.1 SERIES 15 Pumps Cutaway View (Packed Type) 8-15-0 GPM Sizes (--7 m³/hr) MECHANICAL SEAL (SERIES 415) G - HL, K - LL SIZES AK, AL, LS - M SIZES BRACKET 5 416 SHAFT
More informationVIKING UNIVERSAL SEAL PUMPS. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options. Operating Range: Nominal Flow Rates:
VIKING UNIVERSAL SEAL PUMPS Section 630 Page 630. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Options Standard Pump (shown: KK123A) Jacketed Pump (shown: KK4223A) Nominal Flow Rates: Pump
More informationVIKING HEAVY DUTY PUMPS
SERIES 495 STANDARD CONSTRUCTION Section 44 Page 44. Issue D FEATURES Range Temperature Range Viscosity Range 250 PSI (7 BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU ( cst to cst) 00
More informationCoro-Flo Sales Catalog
LPGCFP100C LPG Pumps Coro-Flo Sales Catalog FF-Model DL-Model DLF-Model C-Model Table of Contents General Information What is a Coro-Flo Pump...3 History of the Coro-Flo Pump... 4 Markets Served... 4 Model
More informationLACT PERFORMANCE PRODUCTS
LACT PRODUCTS DURABLE & RELIABLE SOLUTIONS BOLTS PLUG LID Low Pressure Drop Inclined basket design for low pressure drop and high system efficiency O-RING Easy to Clean Top basket removal eliminates the
More informationPIPELINE INJECTION PRODUCTS
PIPELINE INJECTION PRODUCTS DURABLE & RELIABLE SOLUTIONS PIPELINE INJECTION PUMP GP-10 & GP-1 SERIES Flows up to: 210 GPM / BPH / 7,20 BPD (nominal flow) BUSHINGS BACK PULL OUT SEAL HEAD DRIVER SHAFT DRIVEN
More informationVISCOSITY RANGE GPM m 3 h PSI Bar F C SSU cst
UNIVERSL PRODUCT LINE: SERIES 724, 4724 Section 1706 Page 1706.1 Issue B TBLE OF CONTENTS Features & Benefits...2 Cutaway View & Pump Features...2 Model Number Key...3 Standard Materials of Construction...3
More informationHydraulic gear pumps and motors
PL 01 T E DISPLACEMENTS From To Hydraulic gear pumps and motors 0.07 in 3 /rev (1.07 cm 3 /rev) 5.56 in 3 /rev (91.10 cm 3 /rev) through bore aluminum body PRESSURE Max. Continuous Max. Intermittent Max.
More informationVIKING GENERAL PURPOSE PUMPS SERIES 32 AND 432
Page 310.1 FEATURES SERIES 32 and 432 3 GPM (.7 m³/hr) Size Shown. or Mechanical seal type. Valve on casing. SERIES 432 5 GPM (1 m³/hr) Mechanical seal type. Shown with valve on head. C, F & FH Sizes J
More informationBSM ROTARY GEAR PUMPS
-SERIES FLG. MTD. PUMP PUMP FOOT The BSM -Series pumps are designed to provide quiet and efficient service at standard motor speeds, moderately high pressures. Typical applications are supplying hydraulic
More informationCLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM
CLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM DESCRIPTION Series S pumps are general purpose positive displacement gear pumps and are a good choice
More informationROTAN INTERNAL GEAR PUMPS. Serving industry since 1921 Available in cast iron, carbon steel, and stainless steel construction
DESMI INC. ROTAN INTERNAL GEAR PUMPS Serving industry since 1921 Available in cast iron, carbon steel, and stainless steel construction GP/HD/PD/CD/MD SERIES DESMI ROTAN, one of the world s leading manufacturers
More informationA Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer
THE LEADING FORCE behind liquids since 1857 A Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer The Roper Pump Family of Gear
More informationMOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1441 Page 1441.
MOTOR SPD PRODCT LIN: SRIS 495, 495 Section 44 Page 44. Issue TL OF CONTNTS Features & enefits...2 Standard Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4 Mounting
More informationRSV Series In-Line Vertical Multi-Stage, Ring Section Pump September 2013
1.0 Overview. The RSV series is Carver s multi-stage pump for water with maximum working pressures below 440 PSI. For other clean liquids please contact Carver Pump Company or your local distributor. The
More informationVIKING HEAVY DUTY PUMPS SERIES 4193 AND 493 STEEL EXTERNALS FEATURES
VIKING HEAVY DUTY PUMPS SERIES 49 AND 49 FEATURES Section 54 Page 54. Issue C Pressure Range 2 Temperature Range Viscosity Range 250 PSI ( BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU
More informationEFQT/EFQU. EBARA Self Priming Trash Pump. Contents Project: Model: Chk d: Date:
Contents Section Page Model Designation 2 Features 3 Standard Specifications 5 Specifications 6 Selection Chart 7 Suction Speed Flow Chart 9 Performance Curves 10 Dimension Drawings 20 Model Designation
More informationViking SL Industrial Lobe Pump Series
Section 288 Page 288. Viking SL Industrial Lobe Pump Series This product brings gentle low shear pumping action with in-line cleaning capabilities to the industrial markets. Rugged enough for corrosive
More informationITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.
ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L
More informationVISCOSITY RANGE GPM m 3 h PSI Bar F C SSU cst
SERIES 493, 493 Section 34 Page 34. TBLE OF CONTENTS Features & Benefits...2 Specifications...2 Standard Materials of Construction...2 Key...3 Cutaway View & Pump Features...3 Mountg Options...4 Dimensions
More informationVIKING. Metric Motor Speed Pumps
Metric Motor Speed Pumps VIKING Serving Applications For: Chemical Processors Grain Processors Rotating Equipment OEMs Petroleum Products And Many Others Flows: to 45 M 3 /Hr Pressures: to 17 BAR Viscosities:
More information1SV (e-sv) 60 Hz 3500 RPM
DIMENSIONS AND ENGINEERING PAGE 31 CONSTRUCTION: 34 STAINLESS STEEL NOMINAL FLOW: 9 GPM CAPACITIES: 2-12 GALLONS PER MINUTE HEADS: 13 372 PSI TDH STAGING: 2 3 MINIMUM FLOW: 2 GPM MAXIMUM WORKING 36 PSI
More information1SV (e-sv) 50 Hz 2900 RPM
DIMENSIONS AND ENGINEERING PAGE 37 CONSTRUCTION: 34 STAINLESS STEEL NOMINAL FLOW: 9 GPM CAPACITIES: 2-12 GALLONS PER MINUTE HEADS: 13 372 PSI TDH STAGING: 2 3 MINIMUM FLOW: 2 GPM MAXIMUM WORKING 36 PSI
More informationEclipse. The Power of Design Innovation. Series
Eclipse The Power of Design Innovation Series Pulsafeeder Technology Since 1936, Pulsafeeder has been recognized as a world leader in fluid handling and control technology. Pulsafeeder continues to deliver
More informationProduct Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE
Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,
More informationCASING COVER PLATE LUBRICATION GASKETS PRESSURE RELIFE VALVE SEAL OPTIONAL EQUIPMENT
Series: PFSPT Self-Priming Centifugal Pumps Size: x, Solids -1/ DISCHARGE x, lbs. Flange LIQUID TEMPERATURE 1 F CASING IMPELLER SHAFT SHAFT SLEEVE WEAR RING COVER PLATE FLAP VALVE Gray Iron ASTM A- Class
More informationVIKING HEAVY DUTY PUMPS SERIES 4197 STAINLESS STEEL FEATURES
VIKING HEAVY DUTY PUMPS FEATURES Section 64 Page 64. s Cutaway View 0--0 GPM Sizes (2-4.5-7 m³/hr) s Cutaway View 5-50-75 GPM Sizes (8--7 m³/hr) Pressure Range Temperature Range Viscosity Range 0 PSI (4
More information390 Series Multi-Stage Vertical In-Line Centrifugal Pumps
Bulletin 390 /Rev. B 390 Series Multi-Stage Vertical In-Line Centrifugal Pumps Capacities to 400 G.P.M. (91 M 3 /HR) Heads to 800 Feet (243 Meters) Temperatures to 250 F (120 C) motralec 4 rue Lavoisier.
More informationDOUBLE, P.O. CHECK VALVES (PRE-ENGINEERED BLOCKS)
DOUBLE, P.O. CHECK VALVES (PRE-ENGINEERED BLOCKS) SERIES DOUBLE PILOT OPERATED CHECK VALVE... HS3 Page HD1 Page HD2 SERIES DOUBLE PILOT OPERATED CHECK VALVE GPM PSI LPM BAR CAVITY MODEL PAGE 5 3500 19
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP B-Series pumps are a good choice for a variety of recirculating, mixing, and transfer applications. Typical pumped liquids include solvents, resins, and petroleum products. These pumps are
More informationEN. 850 Filtrate Pumps. Technical Specification Pages
850 17.01.EN 850 Filtrate Pumps Technical Specification Pages 850 Series Filtrate Pump 850 17.01.EN This page left intentionally blank. 1.0 Overview. The 850 is Carver s filtrate pump line designed for
More informationModel Z4500 Stationary Pump
LPGCVP3C Sales Catalog for Stationary and Truck Pumps Model Z32 Truck Pump Model Z35 Stationary and Truck Pump Model Z45 Stationary Pump Model C51 Direct-Coupled Mounting Model 121 Stationary Coro-Vane
More informationUTN-L / UTN-BL I frame
UTN-L / UTN-BL I frame Lined Magnetic Drive Process Centrifugal Pumps UTN-BL PFA CLOSE COUPLED EXECUTION Plastic and Fluoroplastic Lined Magnetic drive Horizontal - Single Stage - Process Centrifugal pumps
More informationFLOMAX SELF PRIMING CENTRIFUGAL PUMP FEATURES. 3 MP PUMPS, INC. PHONE: (800) FAX: (586) FLOMAX 5 FLOMAX 8
FLOMAX 5 8 10 SELF PRIMING CENTRIFUGAL PUMP FEATURES CLOSED COUPLED TO ELECTRIC MOTOR PUMPAK ONLY TO MOUNT TO STANDARD NEMA C FACE MOTOR FLOWS - 100-750 GPM PRESSURES - 100-230 FEET HEAD AVAILABLE IN:
More informationVIKING HEAVY DUTY PUMPS SERIES 225 AND 4225 JACKETED BRACKET, STANDARD CONSTRUCTION FEATURES
VIKING HEAVY DUTY PUMPS JACKETED BRACKET, STARD CONSTRUCTION FEATURES SERIES 5 Pumps Cutaway View 5-0-60-80-5 GPM Sizes (-7--8- m³/hr) Section Page. Issue C MECHANICAL SEAL (SERIES 5) H - LL SIZES LS -
More informationVeljan Gear Pumps. E' Series Features:-
E' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 43.5cc/rev to 146.5cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 38.7gpm High strength
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA3 RA2 DEAN PUMP SERIES RA FAN COOLED HIGH TEMPERATURE HOT OIL PUMPS No Liquid Cooling Required
More informationGear Housing Widths 1.00" 1.25" 1.50" 1.75" 2.00" 2.25" 2.50" Gear Housing Widths / Flow Rate [ VGP - D Series ]
'D' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 20.6cc/rev to 104.2cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 27.5gpm High strength
More informationDPS. The SSV Dual Pump System
DPS The SSV Dual Pump System A Full Range of Product Features The DPS series of 36L stainless steel vertical multi-stage pumps from G&L has been designed to provide reliable high pressure boosting to serve
More informationFeatures: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
More informationFlow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer
Screw pump Series LPD Product description Flow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer The LPD pump is used for a number of different fluids:
More informationSpecifications. Ansimag KF Series Pumps for Chemical Process. Models: KF2110 KF31510 KF3210 KF4310 KF4310H KF6410
Specifications Ansimag KF Series Pumps for Chemical Process Models: KF2110 KF31510 KF3210 KF4310 KF4310H KF6410 English Original, September 2015 1 DESCRIPTION Sealless Horizontal, End Suction, Mag-drive
More informationPRODUCT OBSOLETED 1Q16
VIKING HEAVY DUTY PUMPS FEATURES Section 6 Page 6. Issue C 9 SERIES 27 s Cutaway View (Packed Type) 60-200-280 GPM Sizes (36-45-64 m³/hr) Shown without over-pressure relief valve MECHANICAL SEAL (SERIES
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationEngineering Data Pack GlobalGear Series Pump US
Engineering Data Pack GlobalGear Series Pump US Excellence at work. Excellence in life. Table of Contents GG015 - GG030 with Angle Ports (Flanged Only) Mounting Dimensions 3 IG015I - IG030I with Integral
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL MAGNETIC DRIVE - CAST IRON & DUCTILE IRON PUMPS SERIES SG & SGN SIZES
More informationModel 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS
Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP The Heavy Duty S-Series pumps are designed to handle a wide variety of liquids and are particularly suitable for bulk transfer applications where long life and dependable service is required.
More informationVeljan Gear Pumps. 'B' Series Features:
'' Series Features: Self-priming pumps Heavy duty sleeve bushing design in a small frame size Displacements from 9.8cc/rev to 39.9cc/rev Working pressures up to bar Speeds up to rpm Flows up to 10.5gpm
More informationour contribution for Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB environmental protection
Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB our contribution for environmental protection General DICKOW-pumps of series HZM are sealless multistage horizontal centrifugal
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA296 RA3146 RA3186 RA296 The smaller, foot mounted economy version of the air-cooled RA series
More informationmagnetic drive gear pump
SERIES GA/GAH magnetic drive gear pump Series GA/GAH When you need a low flow pump that delivers high performance, Series GA/GAH provides precise, pulseless flows from as low as 10 ml/min and system pressures
More informationKIRLOSKAR ROMAK PUMP - RMK ISO 2858 / DIN EN / ISO 5199
KIRLOSKAR ROMAK PUMP - RMK ISO 2858 / DIN EN 22858 / ISO 5199 MAGNETIC DRIVE PUMP TYPE - RMK RANGE Discharge capacity (Q) : 3 Up to 300 m /hr Delivery head (H) : Up to 150 m (at 2900 rpm) Available nominal
More informationTHE LEADING FORCE behind liquids since 1857
THE LEADING FORCE behind liquids since 1857 High Capacity Bulk Liquid Handling Pumps - For loading/unloading transport truck tankers, railway tank cars, and barges - High flow rate transfer capability
More informationA measured step forward. CENTRAN TM - Centrifugal Transfer Pumps
A measured step forward CENTRAN TM - Centrifugal Transfer Pumps TM Lutz-JESCO Centrifugal Pumps Products you can rely on Lutz-JESCO s CENTRAN TM - Magnetic Drive Centrifugal - pumps are the ideal complement
More informationPFM6 Digital Portable Hydraulic Tester
PFM6 Digital Portable Hydraulic Tester temperature Helical tube pressure gauge One toggle switch to control power and pressure Platinum resistance temperature sensor Pressure surge protection with internal
More informationEMTEC Series 3-Screw
EMTEC Series 3-Screw Coolant and Emulsion Pumps The reliable pump people Rotary Screw Pumps Performance Shown at 1.8 cst, 3500 RPM Differential Pressure PSI 20-38 20-46 20-56 40-38 40-46 80-36 80-46 140-39
More informationGEAR PUMPS TOUGH INTERNAL GEAR SIMPLE SIMPLE EXTERNAL GEAR COST EFFECTIVE COST EFFECTIVE
TOUGH INTERNAL GEAR GEAR PUMPS SIMPLE SIMPLE EXTERNAL GEAR COST EFFECTIVE COST EFFECTIVE NOMAD GEAR PUMPS California-based JDA GLOBAL LLC, the world s largest provider of after-market diaphragm pump products,
More informationL Q LIQUID-SPECIFIC PRODUCT LINE: CAST IRON ASPHALT PUMPS SERIES DESCRIPTION (34 & 32E) OPERATING RANGE: MODEL NUMBER KEY:
LIQUID-SPECIFIC PRODUCT LINE: SERIES 4A, 4AE, 44A, 44AE, 34A, 434A, 14E, 34E, 34, 3E Section 430 Page 430.1 Issue S SERIES DESCRIPTION (34 & 3E) Viking 34 Series Asphalt Pumps are designed to handle asphalts,
More informationVersa-Matic. Operating Manual. 3/8" Bolted Plastic Pumps. Polypropylene Kynar
Versa-Matic Operating Manual 3/8" Bolted Plastic Pumps Polypropylene Kynar E8 SAFETY WARNINGS Read these instructions completely before installation and start-up. It is the responsibility of the purchaser
More informationE8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions
E8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions Polypropylene SAFETY WARNINGS Read these instructions completely before installation and start-up. It is the responsibility of the purchaser
More informationCONSOLIDATED BILL OF MATERIALS (BOM) FOR STANDARD H-SERIES GEAR PUMPS
CONSOLIDATED BILL OF MATERIALS (BOM) FOR STANDARD H-SERIES GEAR PUMPS Model H14F Sealed, Long-Coupled Model H14F Sealed or Mag-Drive, Close-Coupled Table of Contents Model H14F: SEALED-Long-Coupled: 316
More informationVIKING HEAVY DUTY ALLOY PUMPS SERIES 724 AND 4724
VIKING HEAVY DUTY ALLOY PUMPS Section 210 Page 210.1 FEATURES SERIES 4724 Cutaway View Mechanical, 1½, 3 and 5 GPM Sizes 1 Range 200 PSI (14 BAR) for (21 cst) and above (Small Pumps F, FH and G sizes)
More informationRegenerative Turbine Pumps
Bulletin E4 November 009 E4 T4 Series Regenerative Turbine Pumps Capacities to GPM Heads to 600 Feet Temperatures to 00 F MTH PUMPS MTH E4 T4 Series Close-coupled and pedestal mounted regenerative turbine
More informationRSV In-Line Vertical Multi-Stage, Ring Section Pumps
RSV In-Line Vertical Multi-Stage, Ring Section s Technical Specification Pages RSV In-Line Vertical Multi-Stage, Ring Section This page left intentionally blank. RSV In-Line Vertical Multi-Stage, Ring
More informationMICROPUMP MAG-DRIVE GEAR PUMPS
MAG-DRIVE GEAR PUMPS REVISION # 1 DATE: 6-6-6 WETTED MATERIALS Pump housings: 316 stainless steel. Gears: PEEK. Gear shafts: 316 stainless steel. Gear shaft bearings: PEEK. Driven magnet: Totally encapsulated
More informationD1AFF Fleet Fueling Dispensers
D1AFF Fleet Fueling Dispensers (Mechanical Register) 6102 One in a series of the finest dispensers, all designed with you in mind. Compare these features & benefits Compact D1AFF Aluminum Cabinet 1" Neptune
More informationWMDA Series WMDA. Seal-less Mag-Drive Pumps. MAG-DRIVE ANSI-B73.1 ISO-2858 or API-685 CENTRIFUGAL PUMPS
Seal-less Mag-Drive Pumps Seal-less Mag-Drive Pump Specialists WORKING LIMITS QMAX = 1800 USGPM @ 3500RPM; 350 cm/h @ 2900 RPM HMAX = 700 ft @ 3500RPM; 150 m @ 2900RPM T = -212 F (-100 C) up to 662 F (350
More information