MODEL SCS REMOTE CONDENSER

Transcription

1 FEATURES REMOTE CONDENSER CONDENSING UNIT MODEL SCS REMOTE CONDENSER FROM 3/4 TO 40 HP MODEL WCS WATER-COOLED CONDENSER FROM 3/4 TO 40 HP 1 WATER-COOLED CONDENSING UNIT SEMI-HERMETIC COMPRESSOR

2 TABLE OF CONTENTS NOMENCLATURE STANDARD FEATURES FACTORY INSTALLED OPTIONS CAPACITY CAPACITY SCS/WCS (008 TO 400) HIGH TEMPERATURE, R-22/R-407C CAPACITY SCS/WCS (008 TO 300) LOW TEMPERATURE, R CAPACITY SCS/WCS (008 TO 400) MEDIUM TEMPERATURE, R-404A/R CAPACITY SCS/WCS (008 TO 300) LOW TEMPERATURE, R-404A/R ELECTRICAL DATA ELECTRICAL DATA SCS/WCS (008 TO 400) HIGH AND MEDIUM TEMPERATURES ELECTRICAL DATA SCS/WCS (008 TO 300) LOW TEMPERATURE DRAWINGS MODEL SCS REMOTE INDOOR CONDENSING UNIT MODEL SCS REMOTE INDOOR CONDENSING UNIT (STACKABLE) MODEL WCS WATER-COOLED CONDENSING UNIT RECEIVER DATA SPECIFICATIONS NOMENCLATURE UNIT MODEL S = Remote Condenser W = Water-Cooled Condenser M = Salt-Water Cooled Condenser UNIT TYPE C = Condensing Unit Horizontal Air Flow COMPRESSOR TYPE S = Semi-Hermetic SIZE Nominal Compressor HP SIZE Fractional Compressor HP S C S H 2 9 REFRIGERANT 2 = R-22 3 = R-134a 4 = R-404A/R = R-407C APPLICATION H = High Suction M = Medium Suction L = Low Suction UNIT VOLTAGE 2 = 240/1/60 5 = /3/60 8 = 575/3/60 9 = 480/3/60 COMPRESSOR 1 = Copeland 2 = Carlyle 5 = Bitzer 2

3 FEATURES STANDARD FEATURES Heavy-gauge galvanized steel base Liquid receiver with isolating valves and safety relief valve or fusible plug (SCS) Spring mounted semi-hermetic compressor with vibrasorbers Cleanable water-cooled condenser with insulating valve and safety relief Crankcase heaters Electrical control panel complete with compressor contactors, condenser interlock (SCS), control transformer, pump-down switch and terminal block Manual reset, fix, high pressure switch Automatic reset, adjustable low pressure switch with flexible hose Oil failure switch (compressor with positive pressure oil pump) 240/1/60 control circuit FACTORY INSTALLED OPTIONS Liquid line kit complete with liquid drier (sealed or replaceable), sight glass/moisture indicator (installed) and liquid line solenoid valve (shipped loose) Suction filter (sealed or replaceable) Suction accumulator Oil separator including check valve, recommended for 10 F/-23 C room and lower (SCS) Oil separator, recommended for 10 F/-23 C room and lower (WCS) Compressor, rigid mounting without vibrasorbers Non-fused disconnect switch Fused disconnect switch Adjustable dual pressure switch with flexible hoses Compressor discharge thermostat 3-pipe hot gas defrost kit, single evaporator 3-pipe hot gas defrost kit, multiple evaporators (recommended with medium temperature application) Electric defrost timer Electric defrost kit complete with timer, heater and fan contactors, fuses and compressor/heaters interlock switch Air defrost timer 120/1/60 or 24/1/60 control circuit Capacity control: unloading and/or hot gas bypass Programmable electronic controller complete with room thermostat, temperature display, defrost timer, alarm and many programmable operation functions Water regulating valve (WCS) Stackable units Carlyle or Bitzer semi-hermetic compressor Fixed or adjustable flooding valve (SCS) Discharge check valve 3

4 CAPACITY CAPACITY SCS/WCS (008 TO 400) HIGH TEMPERATURE, R-22/R-407C Model Cond. Saturated Suction Temp. F (Capacity MBH) Line Size Receiver (lb.) Shipping Compressor Temp Suction Liquid Std Opt Weight (lb.) H KAN /8 3/ H KAR /8 3/ H KAGB /8 3/ H KAKB /8 3/ H ERF /8 1/ H NRB /8 1/ H NRA /8 1/ H DC (4) /8 1/ NA H DD /8 1/ NA H DL /8 5/ NA H DA /8 5/ NA H DA3A /8 5/ NA H DB3A /8 7/ NA H DS3A /8 7/ NA H DA /8 7/ NA H DH /8 1 1/ NA H DJ /8 1 1/ NA H DH /8 1 1/ NA H DJ /8 1 1/ NA NOTE : (1) Receiver holding charge (lb.) is based on 90% full at 90 F (For SCS only) (3) For R-407C refrigerant, multiply capacity by 0.98 and POE oil compressor (2) For 50 Hz operation, multiply capacity by 0.83 must be used (4) Capacity and range apply to 3-phase units only 4

5 CAPACITY CAPACITY SCS/WCS (008 TO 300) LOW TEMPERATURE, R-22 Model Cond. Saturated Suction Temp. F (Capacity MBH) Line Size Receiver (lb.) Shipping Compressor Temp Suction Liquid Std Opt Weight (lb.) L KAMB /8 3/ L KAJB /8 3/ L KAKB /8 3/ L EADA /8 3/ L EAVB /8 3/ L LAHA /8 1/ L DF /8 1/ L DL /8 1/ L DA /8 1/ L DA3A /8 5/ L DB3A /8 5/ L DF3A /8 5/ L DS3A /8 7/ L DL /8 7/ L DT /8 7/ L DL /8 1 1/ L DT NOTE : (1) Receiver holding charge (lb.) is based on 90% full at 90 F (For SCS only) (2) For 50 Hz operation, multiply capacity by /8 1 1/

6 CAPACITY CAPACITY SCS/WCS (008 TO 400) MEDIUM TEMPERATURE, R-404A/R-507 Model Cond. Saturated Suction Temp. F (Capacity MBH) Line Size Receiver (lb.) Shipping Compressor Temp Suction Liquid Std Opt Weight (lb.) NA 010-1M NA KARB-010E NA 5/8 3/ NA NA 015-1M NA KAKB-021E NA 7/8 3/ NA NA 020-1M NA ERCA-021E NA 7/8 3/ NA NA 030-1M NA ERFA-031E NA 1 1/8 1/ NA NA 040-1M NA NRB2-040E NA 1 1/8 1/ NA M DC3-050E /8 1/ M DD3-050E /8 1/ M DL3-075E /8 5/ M DA3-075E /8 5/ M DA3A-075E /8 5/ M DB3A-100E /8 7/ M DS3A-150E /8 7/ M DA3-200E /8 7/ M DH3-250E /8 1 1/ M DJ3-300E /8 1 1/ M DH3-350E /8 1 1/ M DJ3-400E /8 1 1/ NOTE : (1) Receiver holding charge (lb.) is based on 90% full at 90 F (For SCS only) 6

7 CAPACITY CAPACITY SCS/WCS (008 TO 300) LOW TEMPERATURE, R-404A/R-507 Model Cond. Saturated Suction Temp. F (Capacity MBH) Line Size Receiver (lb.) Shipping Compressor Temp Suction Liquid Std Opt Weight (lb.) L KAMB-007E /8 3/ L KAJB-010E /8 3/ L KAKB-011E /8 3/ L KALB-015E /8 3/ L EADB-021E /8 3/ L EAVB-021E /8 3/ L LAHB-032E /8 1/ L DF3-030E /8 1/ L DL3-040E /8 1/ L DA3-060E /8 1/ L DA3A-060E /8 5/ L DB3A-075E /8 5/ L DF3A-090E /8 5/ L DS3A-100E /8 7/ L DL3-150E /8 7/ L DT3-220E /8 7/ L DL3-270E /8 1 1/ L DT3-300E /8 1 1/ NOTE : (1) Receiver holding charge (lb.) is based on 90% full at 90 F (For SCS only) (2) For 50 Hz operation, multiply capacity by

8 ELECTRICAL DATA 8 ELECTRICAL DATA SCS/WCS (008 TO 400) HIGH AND MEDIUM TEMPERATURES Standard Unit Electric Defrost Option Model Number (1) (2) Voltage Compressor Disc. Sw. Evap. Motor Elec. Def. Disc. Sw. MCA (4) MOP (4) MCA (4) MOP (4) Model (3) Qty RLA LRA Amp. Amp. Amp. Amp. (1)-008-1H /1/60 KAN CAV (1)-008-1H /3/60 KAN TAC (1)-010-1H /1/60 KAR CAV (1)-010-1H /3/60 KAR TAC (1)-010-1M /1/60 KARB-010E-CAV (1)-010-1M /3/60 KARA-010E-TAC (1)-015-1H /1/60 KAGB-0150-CAV (1)-015-1H /3/60 KAGA-0150-TAC (1)-015-1M /1/60 KAKB-021E-CAV (1)-015-1M /3/60 KAKA-020E-TAC (1)-020-1H /1/60 KAKB-0200-CAV (1)-020-1H /3/60 KAKA-0200-TAC (1)-020-1H /3/60 ERA TAE (1)-020-1H /3/60 KAKA-0200-TAD (1)-020-1M /3/60 ERCA-021E-TAC (1)-020-1M /3/60 ERCA-020E-TAE (1)-030-1H /1/60 ERF CAB (1)-030-1H /3/60 ERF TAC (1)-030-1H /3/60 ERF TAE (1)-030-1H /3/60 ERF TAD (1)-030-1M /3/60 ERFA-031E-TAC (1)-030-1M /3/60 ERFA-031E-TAE (1)-030-1M /3/60 ERFA-031E-TAD (1)-040-(2) /3/60 NRB2-040(3)-TFC (1)-040-1H /3/60 NRB TFE (1)-040-1H /3/60 NRB TFD (1)-040-1M /3/60 NRB2-040E-TFD (1)-049-1H /3/60 NRA TFC (1)-049-1H /3/60 NRA TFE (1)-049-1H /3/60 NRA TFD (1)-050-1H /1/60 2DC CFB (1)-050-(2) /3/60 2DC3-050(3)-TFC (1)-050-(2)-8 600/3/60 2DC3-050(3)-TFE (1)-050-(2)-9 480/3/60 2DC3-050(3)-TFD (1)-060-(2) /3/60 2DD3-050(3)-TFC (1)-060-(2)-8 600/3/60 2DD3-050(3)-TFE (1)-060-(2)-9 480/3/60 2DD3-050(3)-TFD (1)-070-(2) /3/60 2DL3-075(3)-TFC (1)-070-(2)-8 600/3/60 2DL3-075(3)-TFE (1)-070-(2)-9 480/3/60 2DL3-075(3)-TFD (1)-080-(2) /3/60 2DA3-075(3)-TFC (1)-080-(2)-8 600/3/60 2DA3-075(3)-TFE (1)-080-(2)-9 480/3/60 2DA3-075(3)-TFD (1)-090-(2) /3/60 3DA3A-075(3)-TFC (1)-090-(2)-8 600/3/60 3DA3A-075(3)-TFE (1)-090-(2)-9 480/3/60 3DA3A-075(3)-TFD (1)-100-(2) /3/60 3DB3A-100(3)-TFC (1)-100-(2)-8 600/3/60 3DB3A-100(3)-TFE (1)-100-(2)-9 480/3/60 3DB3A-100(3)-TFD (1)-150-(2) /3/60 3DS3A-150(3)-TFC (1)-150-(2)-8 600/3/60 3DS3A-150(3)-TFE (1)-150-(2)-9 480/3/60 3DS3A-150(3)-TFD (1)-200-(2) /3/60 4DA3-200(3)-TSK (1)-200-(2)-8 600/3/60 4DA3-200(3)-TSE (1)-200-(2)-9 480/3/60 4DA3-200(3)-TSK (1)-250-(2) /3/60 4DH3-250(3)-TSK (1)-250-(2)-8 600/3/60 4DH3-250(3)-TSE (1)-250-(2)-9 480/3/60 4DH3-250(3)-TSK (1)-300-(2) /3/60 4DJ3-300(3)-TSK (1)-300-(2)-8 600/3/60 4DJ3-300(3)-TSE (1)-300-(2)-9 480/3/60 4DJ3-300(3)-TSK (1)-350-(2) /3/60 6DH3-350(3)-TSK (1)-350-(2)-8 600/3/60 6DH3-350(3)-TSE (1)-350-(2)-9 480/3/60 6DH3-350(3)-TSK (1)-400-(2)-8 600/3/60 6DJ3-400(3)-TSE (1)-400-(2)-9 480/3/60 6DJ3-400(3)-TSN NOTE : (1) Model SCS, WCS and MCS from 008 to 400 (2) Use suffix 1H2 for R-22 and suffix 1M4 for R-404A and R-507 (3) Use suffix 0 for mineral oil with R-22 and suffix E for Polyol Ester oil with R-22, R-404A, R-507 and R-134a (4) MCA: Minimum Circuit Ampacity, MOP: Maximum Overcurrent Protection.

9 ELECTRICAL DATA ELECTRICAL DATA SCS/WCS (008 TO 300) LOW TEMPERATURE Standard Unit Electric Defrost Option Model Number (1) (2) Voltage Compressor Disc. Sw. Evap. Motor Elec. Def. Disc. Sw. MCA (4) MOP (4) MCA (4) MOP (4) Model (3) Qty RLA LRA Amp. Amp. Amp. Amp. (1)-008-1L /1/60 KAMB-0075-CAV (1)-008-1L /3/60 KAMA-0075-TAC (1)-008-1L /1/60 KAMB-007E-CAV (1)-008-1L /3/60 KAMA-007E-TAC (1)-010-1L /1/60 KAJB-0100-CAV (1)-010-1L /3/60 KAJA-0101-TAC (1)-010-1L /1/60 KAJB-010E-CAV (1)-010-1L /3/60 KAJA-011E-TAC (1)-015-1L /1/60 KAKB-0200-CAV (1)-015-1L /3/60 KAKA-0200-TAC (1)-015-1L /1/60 KAKB-011E-CAV (1)-017-1L /1/60 KALB-015E-CAV (1)-017-1L /3/60 KALA-016E-TAC (1)-020-1L /1/60 EADB-0200-CAB (1)-020-1L /3/60 EADA-0200-TAC (1)-020-1L /1/60 EADB-021E-CAB (1)-020-1L /3/60 EADA-020E-TAC (1)-025-1L /1/60 EAVB-0210-CAV (1)-025-1L /3/60 EAVA-0210-TAC (1)-025-1L /3/60 EAVA-0210-TAD (1)-025-1L /1/60 EAVB-021E-CAV (1)-025-1L /3/60 EAVA-021E-TAC (1)-025-1L /3/60 EAVA-021E-TAE (1)-025-1L /3/60 EAVA-021E-TAD (1)-030-1L /1/60 LAHB-0311-CAB (1)-030-1L /3/60 LAHA-0310-TAC (1)-030-1L /3/60 LAHA-0310-TAD (1)-030-1L /1/60 LAHB-032E-CAB (1)-030-1L /3/60 LAHA-032E-TAC (1)-030-1L /3/60 LAHA-032E-TAE (1)-030-1L /3/60 LAHA-032E-TAD (1)-040-(2)-2 240/1/60 2DF3-030(3)-CFB (1)-040-(2) /3/60 2DF3-030(3)-TFC (1)-040-(2)-8 600/3/60 2DF3-030(3)-TFE (1)-040-(2)-9 480/3/60 2DF3-030(3)-TFD (1)-050-(2) /3/60 2DL3-040(3)-TFC (1)-050-(2)-8 600/3/60 2DL3-040(3)-TFE (1)-050-(2)-9 480/3/60 2DL3-040(3)-TFD (1)-060-(2) /3/60 2DA3-060(3)-TFC (1)-060-(2)-8 600/3/60 2DA3-060(3)-TFE (1)-060-(2)-9 480/3/60 2DA3-060(3)-TFD (1)-070-(2) /3/60 3DA3A-060(3)-TFC (1)-070-(2)-8 600/3/60 3DA3A-060(3)-TFE (1)-070-(2)-9 480/3/60 3DA3A-060(3)-TFD (1)-080-(2) /3/60 3DB3A-075(3)-TFC (1)-080-(2)-8 600/3/60 3DB3A-075(3)-TFE (1)-080-(2)-9 480/3/60 3DB3A-075(3)-TFD (1)-090-(2) /3/60 3DF3A-090(3)-TFC (1)-090-(2)-8 600/3/60 3DF3A-090(3)-TFE (1)-090-(2)-9 480/3/60 3DF3A-090(3)-TFD (1)-100-(2) /3/60 3DS3A-100(3)-TFC (1)-100-(2)-8 600/3/60 3DS3A-100(3)-TFE (1)-100-(2)-9 480/3/60 3DS3A-100(3)-TFD (1)-150-(2) /3/60 4DL3-150(3)-TSK (1)-150-(2)-8 600/3/60 4DL3-150(3)-TSE (1)-150-(2)-9 480/3/60 4DL3-150(3)-TSK (1)-220-(2) /3/60 4DT3-220(3)-TSK (1)-220-(2)-8 600/3/60 4DT3-220(3)-TSE (1)-220-(2)-9 480/3/60 4DT3-220(3)-TSK (1)-270-(2) /3/60 6DL3-270(3)-TSK (1)-270-(2)-8 600/3/60 6DL3-270(3)-TSE (1)-270-(2)-9 480/3/60 6DL3-270(3)-TSK (1)-300-(2) /3/60 6DT3-300(3)-TSK (1)-300-(2)-8 600/3/60 6DT3-300(3)-TSE (1)-300-(2)-9 480/3/60 6DT3-300(3)-TSK NOTE : (1) Model SCS, WCS and MCS from 008 to 300 (2) Use suffix 1L2 for R-22 and suffix 1L4 for R-404A and R-507 (3) Use suffix 0 for mineral oil with R-22 and suffix E for Polyol Ester oil with R-22, R-404A, R-507 and R-134a (4) MCA: Minimum Circuit Ampacity, MOP: Maximum Overcurrent Protection 9

10 DRAWINGS MODEL SCS REMOTE INDOOR CONDENSING UNIT /4 13 3/4 1/2"ø 4 MTG HOLES B A 22 1/4 24 1/4 22 1/4 24 1/4 MODEL 270 TO 400 WITH OPT. RECEIVER MODEL SCS REMOTE INDOOR CONDENSING UNIT (STACKABLE) Std Receiver Opt. Receiver Model No. A B A B 008 to /2 47 1/4 49 1/2 47 1/4 070 to /2 53 1/4 55 1/2 53 1/4 150 to /2 53 1/4 73 1/2 71 1/4 270 to /2 71 1/4 73 1/2 71 1/ /4 B A 22 1/4 24 1/2 10

11 DRAWINGS MODEL WCS WATER-COOLED CONDENSING UNIT B Model No. A B C D 008 to /4 040 to /4 090 to /4 1/2"ø 4 MTG HOLES C 7/8 7/8 1 1/2 1 1/2 D A RECEIVER DATA Dimensions Mounting Refrigerant Charge (lb.) O.D. X Length Position R-22 R-404A 6" X 30" H,V " X 36" H " X 42" H " X 48" H " X 60" H " X 60" H Refrigerant charges are based on 90% full at 90 F For R-134a, multiply R-22 by For R-507, multiply R-404A by 0.88 For R-407C, multiply R-22 by

12 SPECIFICATIONS CASINGS: Remote condenser and water-cooled condensing unit bases and electrical boxes are heavy-gauge galvanized steel (G90) with plated or stainless steel hardware for corrosion-free assembly. WIRING: Compressors and controls are wired using water and oil resistant wire, Type TEW 105 C and protected by plastic or metallic conduit secured with certified connectors. ELECTRICAL BOXES are located on the front of the unit for easy access and service. They are manufactured of heavy-gauge galvanized steel and assembled with plated or stainless steel hardware for corrosion protection. CONTROL PANELS are complete with terminal blocks, control transformer, control circuit fuses, compressor contactors, fan interlock, fix high and adjustable low pressure control, oil failure switch (for compressors with positive pressure oil pump), and a pump-down switch. The wires are numbered and color-coded, conveniently routed in wiring ducts. All terminal blocks are identified to match the wiring diagram. COMPRESSORS are air or suction cooled, refrigeration duty, accessible semi-hermetic. They are supplied with suction and discharge valves, suction strainer, oil filter, oil pump on model 3HP and larger, solid state or line break thermal protection, crankcase heater, mineral oil for HCFC refrigerant and Polyol Ester oil with HFC refrigerant. RECEIVERS (6" dia. and smaller) are UL/CSA certified and are supplied with a fusible plug. Receivers (6 5/8" dia. and larger) are CRN or ASME "U" stamped and are supplied with relief valves. All receivers have inlet and outlet back-seated Rotalock valves. REFRIGERATION FLOODING VALVES are offered as an option. They are either fixed or adjustable pressures and are factory installed (SCS). CONDENSER WATER VALVES are offered as an option. They are pressure actuated and are either 2-way or 3-way (WCS). REFRIGERATION COPPER TUBES are ASTM certified and factory bent using a programmable CNC tube bender. They are manufactured with the minimum number of fittings and brazed joints to reduce the risk of leaks. FACTORY TESTED: All RefPlus units are electrically tested. A Dielectric Voltage Withstand Strength Test is done on all units. The compressors are energized, and the operating sequence and all controls on each unit are factory tested. Refrigeration piping is leak tested and the system is pressurized and sealed with -40 F/-40 C dew point nitrogen. RefPlus Inc. reserves the right to make any changes in the design or specifications of any product at any time without notice. Copyright 2004 by RefPlus Inc. SCS/WCS R0-2K Printed in Canada. 12 USA & CANADA De Coulomb, Boucherville, Quebec Canada J4B 7L8 Tel.: (450) Fax: (450)