Self-aligning rod ends-, pillow block- and flange bearings....plastics

Transcription

1 3. igubal.... Self-aligning rod ends-, pillow block- and flange bearings.....plastics

2 Application Examples: Exciting applications can be viewed online at LIMELIGHT V Stadium paneling bearings of atmospheric resistance. Since these slats can be RESEARCH INSTITUTE SPECIAL-PURPOSE VEHICLE dimension series K are used in the main bearing swiveled, this allows the air flow inside the stadium Mirror adjustment of the telescope is performed vir- Insensitive to dirt and maintenance-free: The rugged assembly of every individual slat owing to their to be regulated. Part number: tually free of backlash with flange bearings. clevises and bearings never give in on the freedom from maintenance, corrosion resistance and bearing KGLM-08 Magnetic influences can be avoided. special-purpose municipal vehicles. (Max-Planck Institut for physics and astrophysics) (Multicar Spezialfahrzeuge GmbH) PACKAGING MACHINE CARAVAN STEP Long service life and, at the same, food-safe Rugged, insensitive to dirt and vibration-dampening design have been implemented in this application rod ends withstand the loads even in worst- with rod ends. case conditions. (Leeb GmbH) (Hymer AG) TEXTILE INDUSTRY CHOCOLATE DECORATION SYSTEM Concentricity errors and jolts are compensated by Decoration without grease by using maintenance- means of clevises in the support of the free rod ends turn all the sweets into sheer thread guide unit more efficiently than the alternative enjoyment. metal product. (Wolf Spezialmaschinen GmbH) (Sahm GmbH & Co. KG)

3 Selection Products Overview Rod Ends Ideal for pneumatic cylinders and gas struts Rod ends with female thread from page 715 Classic design Integrated lock nut For higher forces, For small space For temperatures Classic Design, For small space for easy assembly, selectable ball material selectable ball material requirement, selectable ball material up to +200 C inch dimensions requirement, selectable ball material, inch dimensions KRM/KLM KRM-CL/KLM-CL KCRM/KCLM ERM/ELM ERM-HT/ELM-HT KRI/KLI ERI/ELI page 720 page 722 page 724 page 730 page 734 page 736 page 740 Rod ends with male thread from page 726 Classic design KARM/KALM For higher forces, selectable ball material KARM-CL/KALM-CL For small space requirement, selectable ball material EARM/EALM For temperatures up to +200 C EARM-HT/EALM-HT Classic design, inch dimensions KARI/KALI page 726 page 728 page 732 page 735 page 738 New! Angled and in-line joints from page 742 Angled ball and socket joint WGRM/WGLM Angled ball and socket joint, low-cost WGRM-LC/WGLM-LC Easy assembly and disassembly WGRM-DE/WGLM-DE In-line ball and socket joint AGRM/AGLM In-line ball and socket joint, low-cost AGRM-LC/AGLM-LC Adapter bolt PKRM/PKLM page 742 page 742 page 744 page 745 page 746 page 748 Clevis Joints Weight reduction, very simple assembly with series E rod ends Clevis joint combinations from page 749 Component parts from page 754 Clevis joints with clevis pin and circlip GERMK/GELMK Clevis joints with spring-loaded fixing clip GERMF/GELMF Combination, easy to fit GERMKE/GELMKE Combination, easy to fit GERMFE/GELMFE High strength under impact loads GERM/GELM Spring-loaded fixing clip GEFM Clevis pin and Circlip GM/GSR page 756 page 757 page 758 page 759 page 754 page 760 page 761 Pillow lock earings Cost-effective, maintenance-free, for high radial loads For small space envelope from page 763 New! New! Standard design from page 768 Easy to disassemble, Easy to fit For quick assembly Split housing with For diameters Extremely light, Compensation of Compensation of Adapter for split and low moisture parallel bore up to 150 mm compact design misalignment errors misalignment errors, dimensional housing and ball absorption inch dimensions series E KSTM-GT ESTM ESTM-GT-GT ESTM-GT ESTM-GT150 ESTM-SL KSTM KSTI page 770 page 771 page 772 page 773 page 774 page 775 page 768 page 768 page More information 709

4 Selection Products Overview Flange earings For the support of both the centre and ends of shafts For temperatures up to +80 C from page 777 New! New! For temperatures up to +200 C from page 789 Easy to install For higher radial Universal and Universal and High static load, Easy to install For higher load quick assembly quick assembly split housing radial load EFOM EFSM GFSM-IG GFSM-AG KFSM-GT EFOM-HT EFSM-HT page 782 page 784 page 786 page 787 page 788 page 789 page 790 Pivoting earings Easy to fit, cost-effective, light weight and robust Pressfit bearings from page 791 Easy to fit, Standard, For extremely Low tolerances Standard, For small space Cost-effective, low-cost, selectable easy to fit ball material narrow installation space easy to fit, inch dimensions requirement selectable ball material KGLM-LC KGLM KGLM-SL KGLM-H KGLI EGLM EGLM-LC page 797 page 796 page 798 page 799 page 800 page 801 page 802 Self-aligning clip bearing from page 803 Double joints from page 806 Simply snapping into sheet metal ECLM For high axial and radial loads, selectable ball material ECLM-HD For tolerance compensation, selectable ball material EGFM-T Solid polymer, selectable ball material EGZM Selectable ball stud and tube materials, individual dimensions and alignment WDGM page 803 page 804 page 805 page 806 page 808 page 809 Spherical Thrust earing Weight reduction Selectable ball and tube materials, individual dimensions and alignment KDGM Easy to fit from page 811 To prevent edge loads SAM page 814 Spherical alls Different materials for your particular applications and requirements Seven different ball materials from page 815 Standard, with low wear WKM/WEM Low-cost, good wear resistance RKM/REM For temperatures up to +250 C XKM/XEM Low moisture absorption JKM/JEM Low-cost and low moisture absorption J4KM/J4EM For underwater applications UWEM Clearance-free J4VEM Detectable RN248KM/ RN248EM page 819 page 820 page 821 page 822 page 824 page 825 page 826 page 827 detectable Quickly to find through metal detectable material Detectable from page 829 Rod ends Clevis joints Spherical ball from page 832 from page 834 from page 827 All other products as detectable version on request 710 More information 711

5 self-aligning maintenance-free plain bearings made of high performance polymers puts a complete system of self-alig n ing bearings bearings, pillow block bearings and rod ends at the developer s fingertips. Self-align ing bearings are easy to fit, adapt to all angular deviations and replace special hous ings in many cases. With, the user can take advantage of all the benefits of high performance polymers: vibration dampening, ability to operate in liquids or chemicals, and resistance to dirt and dust, which can impede the performance of greased metal components. The weight of the igubal parts is approx. 80 % lighter than iglidur X for high temperatures iglidur J for low moisture absorption iglidur J4 for low moisture absorption at lower costs iglidur R as a low-cost alternative iglidur UW for under water applications iglidur RN248 as detectable material iglidur J4 with clearance-free balls Spherical balls, page 815 Do not hesitate to ask for technical support concerning the choice of the material. Please contact igus. comparable steel parts. Additional savings are cost-savings at the of purchasing and during operation and on installation space due to their small dimensions. bearings are also extremely cost competitive due to the elimination of maintenance and installation costs. self-aligning bearings are made of a polymer housing for high strengths and a ball made of maintenance-free self-lubricating high performance polymers. Housing There are three housing materials available, each of them offering particular advantages: Standard housings made of igumid G, a highly shockresistant, long-fibre reinforced polymer, suitable for temperatures from 40 C to +80 C High temperature housings made of iguton G, high degree of chemical resistance, suitable for temperatures Spherical alls: from 40 C to +200 C Exceptionally costeffective with very low clearance Inner race set in housings Detectable housings made of RN246 material. Temperature range: from 30 C to +80 C Maintenance-free Dirt can become Lubrication-free Insensitive to dust and embedded for shaft protection Material Table, page 1269 dirt Areas of Application: Corrosion-resistant Temperature resistance bearing elements can be used without problems Can be used in liquid media up to +200 C, depending even in harsh environments. In moist or wet environments, Vibration-dampening on the material the bearings are corrosion resistant, and resistant to weak acids and alkalines. The application temperatures range Spherical In standard bearings, the ball is made of iglidur W300 material, which is known for its low coefficient of friction while running dry and extremely low tendency to stickslip. This is especially important for low loads and very slow movements. is from 30 C to +200 C. Resist ance to dirt and dust is outstanding. Seals are not necessary, even in extremely contaminated conditions. This is true for fine dust as well as coarse dirt, which is present in agricultural equipment. The housing is made of an impact-resistant composite material which tolerates high alternating loads. More information about iglidur W300, page 151 Detectable Taking advantage of its long experience in polymers and Made of the special materials RN248 for the ball based on several tests, igus decided in the last years to and RN246 for the housing, the parts of metal detectable respond more precisely to the different applications and polymer bearings can be verified as foreign particles customers requests by developping balls in other with all common parameters used in the metal detection iglidur materials. technology and thus ensure safe food. Further to the standard material iglidur W300, balls are now available in 6 other materials presenting particular advantages: detectable program, page 829 Material Table, page 1269 Load The load capacity of the maintenance-free bearing element parts is very high at normal ambient temperatures. bearings absorb high forces and weigh only one fifth of traditional, metal bearing hou sings. The excellent dampening properties are based on the fact that the polymer material of the two part bearing can absorb vibrations differently than steel. However, plastic specific properties, such as dependence on temperature and behaviour under long-term stress, must be taken into consideration when using bearings. The load capacity of the rod end should therefore be checked in a practical test, particularly if it will be used under continuous high loads and at elevat ed temperatures. Percentage tensile strength [%] Temperature [ºC] Standard temperatures materials High temperatures material Diagram 01: trends indicate the effect of temperature on the max. load capacity of bearings. Coefficients of Sliding Friction and Speed One important advantage of bearings is that rapid, rotary movements of a mounted shaft take place directly in the portion, made of iglidur W300. In metallic rod ends, rotary motion takes place between the race and the bearing. High speeds can be achieved with bearings. bearings are used in such a way that the angular movements of the bearings take place at the outer diameter. y contrast, rotations of the shaft are supported directly in the inner diameter of the portion. The advantage therefore lies in the polymer vs. steel relationship. Polymer produces lower friction and permits high speeds, even when running dry. Application Temperatures standard bearing elements can be used in temperatures from 30 C to +80 C. The HT-versions can be used at continuous temperatures up to +200 C. Diagram 01 trends indicate the effect of temperature on the load capacity of bearings with standard and high temperature materials. Application Temperatures Standard HT-Version Minimum 30 C 40 C Maximum, long term +80 C +200 C Maximum, short term +120 C +240 C Table 01: Application temperatures of bearings Thread Description Pitch [mm] M M M M M M M M10 F 1.25 M M12 F 1.25 M M M16 F 1.50 M M M20 M M M M M Table 02: Thread pitches of rod ends and clevis joints Chemical Resistance of bearings iglidur W300 and the housing made of igumid G are resistant to weak alkalines, weak acids and fuels, as well as all types of lubricants. The HT-versions can be used for applications with a higher chemical demand. The moisture absorption of depends on the choice of material. The moisture absorption of is approximately 1.3 % of weight in standard atmosphere. The saturation limit in water is 6.5 %. This must be taken into evaluation for applications. If a lower moisture absorption is essential, a look on to the different materials is helpfull. Chemical table, page More information 713

6 rod ends Medium Resistance Standard HT-Version Alcohol + to 0 + Hydrocarbons + + Greases, oils without additives + + Fuels + + Diluted acids 0 to + to 0 Strong acids + to Diluted alkalines + + Strong alkalines 0 + Table 03: Chemical resistance of plain bearings + resistant 0 conditionally resistant not resistant All data given at room temperature [+20 C] Check the Inner Diameter Inadequate test equipment; plug gauge too short Wrong test equipment; caliper Radiation Resistance Self-aligning plain bearings are re sis tant to radiation up to an intensity of Gy. UV Resistance The corrosion resistance of bear ings gives them special value for outside ap plications. bearings are permanently resistant to UV radiation. A small change in colour (dark coloration) of the ball due to UV radiation does not affect the me ch anical, electrical or thermal properties. Tolerances bearings can be used with different tolerances according to each application. They are designed with a large clearance in the standard product, which enables a secure operation even under high peripheral speeds. The inside diameter of the ball has a tolerance of E10. The shafts should have tolerances between h6 and h9. The tolerances are provided in the table below. Please contact us in case you require lower or other bearing tolerances. asic size [mm] Tolerance Gauge falls Gauge hangs to 3 x,01 x,05 > 3 to 6 x,02 x,07 > 6 to 10 x,02 x,08 > 10 to 18 x,03 x,10 > 18 to 30 x,04 x,12 > 30 to 50 x,05 x,15 Table 04: Tolerances of inner diameter ( balls) Tolerance test with gauge Service Life Calculation The expert allows to check the suitability of bearings for every application. You can choose from different bearings and specific load (radial, axial or static, cyclic and dynamic). The expert system will calculate from these input data: The bearing wear The theoretical service life Expertsystem productfinder Rod Ends Maintenance-free, self-lubricating High strength under impact loads High tensile strength Compensation of misalignment Compensation of edge loads Very low weight 714 Life calculation, CAD files and much more support 715

7 rod ends Rod Ends Rod Ends Application Examples rod ends rod ends can also be used in rough environments. They are corrosion-resistant in humid environments and resistant to weak acids and bases. The operation temperature is from 40 C up to +80 C. Rod ends are also insensitive to dirt and dust. Typical sectors of industry and application areas icycle manufacturing Plant design Packaging Offshore etc. Maintenance-free, dry-running High strength under impact loads High tensile strength When to use it? If you want to save weight For rotating, oscillating and linear movements If high-frequency oscillations/vibrations occur If silent operation is required If you need an electrically insulating part If corrosion resistance is required In combination with pneumatic cylinders and gas struts If chemical resistance is required If high stiffness is required Improve technology and reduce costs 110 exciting examples online Compensation of misalignment Compensation of edge loads When not to use it? If temperatures are higher than +80 C HT version, page If rotation speeds higher than 0.5 m/s are required If really high tensile and shear loads occur With a hydraulic cylinder If dimensions above 30 mm are required Low weight Temperature Product range +80º +200º 18 types Ø 2 30 mm 30º 40º Standard High temperature More information 717

8 rod ends Rod Ends Rod Ends Product Overview rod ends Advantages Maintenance-free High strength under impact loads Very high tensile strength for varying loads Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant High vibration-dampening Suitable for rotating, oscillating and linear movements al series K and E, according to standard DIN ISO Available with a metal sleeve to take a higher torque Loads rod ends handle high loads at normal room temperatures, have excellent dampening properties and weigh only a fifth of traditional metallic rod ends. In applications with high continuous loads and high temperatures, the load capacity of rod ends should be tested in an experiment that simulates the application. Coefficients of Friction and Speed One important advantage of bearings is that rapid, rotary movements of a mounted shaft take place directly between the shaft and the iglidur plain bearing. In metallic rod ends, rotary motion takes place between the race and the bearing. High speeds can somes be achieved with bearings. Product Range rod ends are available in the dimensional series K and E for shaft diameters of 2 to 30 mm. Form A with male thread and Form with female thread The dimensional series K and partially E are available in imperial dimensions, as well as a special version containing a stainless steel sleeve in the inner race. This allows a significantly higher torque than for the standard polymer race. Please ask us for more dimensons. Temperatures The rod ends can be used in temperatures from 30 C up to +80 C. The rod ends made of HT-Material are suitable for temperatures up to +200 C (, types A and ). Standard parts rod ends can be used at different tolerances depending on the individual application. In standard form, they are designed with a large amount of bearing clearance, which permits reliable operation even at high rotational speeds. The bore of the inner race is produced to a standard tolerance range. Shafts should also meet recommended tolerances. Please contact us if you have any questions regarding tolerances. Pivot angle α rod ends with female thread Classic design Series K KRM KLM Integrated lock nut for easy assembly, selectable ball material Series K KRM CL KLM CL For higher forces, selectable ball material Series K KCRM KCLM For small space requirement, selectable ball material ERM ELM For temperatures up to +200 C ERM HT ELM HT Classic design, inch dimensions Series K KRI KLI For small space requirement, selectable ball material, inch dimensions ERI/ELI from page 720 page 722 page 724 from page 730 page 734 from page 736 from page 740 rod ends with male thread Classic design Series K KARM KALM For higher forces, selectable ball material Series K KARM CL For small space requirement, selectable ball material EARM/EALM For temperatures up to +200 C EARM HT EALM HT Classic design, inch dimensions Series K KARI KALI from page 726 page 728 from page 732 page 735 from page 738 -Angled and in-line joints Angled ball and socket joint WGRM WGLM Angled ball and socket joint, low-cost WGRM-LC WGLM-LC New! Easy assembly and disassembly WGRM-DE WGLM-DE In-line ball and socket joint AGRM AGLM In-line ball and socket joint, low-cost AGRM-LC AGLM-LC page 742 page 743 page 744 page 745 page 746 accessories for rod ends 718 Life calculation, CAD files and much more support Adapter bolt Series K PKRM PKLM Clevis joints with clevis pin and circlip GERMK/GELMK Clevis joints with spring-loaded fixing clip GERMF/GELMF page 748 page 756 page 757

9 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends with female thread: KRM and KLM Rod ends with female thread: KRM and KLM Standard design Design with metal sleeve (MH) Maintenance-free, self-lubricating High strength under impact loads Very high tensile strength for varying loads Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant High vibration-dampening Suitable for rotating, oscillating and linear movements Very low weight al series K according to standard DIN ISO Available with a metal sleeve for a higher torque I2 h1 d4 d5 C1 d3 W I1 K M-02 Thread L = left-hand thread R = right-hand thread Housing (female thread) al series K Spherical ball: iglidur W300 page 819 Part number Max. static tensile strength Max. static radial load Min. thread depth Max. torque strength Max. torque through ball Short Long Short Long Thread Inner threading Standard Standard Right-hand Left-hand term term term term without MH with MH thread thread [N] [N] [N] [N] [mm] [Nm] [Nm] [Nm] [g] KRM-02 KLM KRM-03 KLM KRM-05 M4 KLM-05 M4 1, KRM-05 KLM-05 1, KRM-06 KLM-06 1, KRM-08 KLM-08 2,100 1, Weight KRM-10 KLM-10 3,100 1, KRM-10 F KLM-10 F 3,100 1, KRM-12 KLM-12 3,600 1, KRM-12 F KLM-12 F 3,600 1, KRM-14 KLM-14 4,000 2,000 1, KRM-16 KLM-16 4,200 2,100 1, KRM-16 F KLM-16 F 4,200 2,100 1, KRM-18 KLM-18 4,600 2,300 1, KRM-20 KLM-20 5,400 2,700 2,100 1, KRM-20 M20 KLM-20 M20 5,400 2,700 2,100 1, KRM-22 KLM-22 7,000 3,500 2,200 1, KRM-25 KLM-25 8,500 4,250 2,300 1, KRM-30 KLM-30 10,500 5,250 2,500 1, KRM-30 M27x2 KLM-30 M27x2 10,500 5,250 2,500 1, Part number E10 d3 d4 d5 C1 h1 l1 l2 W Max. without MH Right-hand thread Left-hand thread KRM-02 KLM M SW04 30 KRM-03 KLM M SW06 30 KRM-05 M4 KLM-05 M M SW09 30 KRM-05 KLM M SW09 30 KRM-06 KLM M SW11 29 KRM-08 KLM M SW14 25 KRM-10 KLM M SW17 25 KRM-10 F KLM-10 F M10 x SW17 25 KRM-12 KLM M SW19 25 KRM-12 F KLM-12 F M12 x SW19 25 KRM-14 KLM M SW22 25 KRM-16 KLM M SW22 23 KRM-16 F KLM-16 F M16 x SW22 23 KRM-18 KLM M18 x SW27 23 KRM-20 KLM M20 x SW30 23 KRM-20 M20 KLM-20 M M20 x SW30 23 KRM-22 KLM M22 x SW32 22 KRM-25 KLM M24 x SW36 22 KRM-30 KLM M30 x SW41 22 KRM-30 M27x2KLM-30 M27x M27 x SW41 22 For rod ends with metal insert please add MH to the part number. Example: KRM-10 MH (Inner-Ø: 10 mm). with MH ±0.2 pivot angle Life calculation, CAD files and much more support 721

10 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends, female thread; 2nd generation: KRM CL and KLM CL Rod ends, female thread; 2nd generation: KRM CL and KLM CL Design with metal sleeve for higher torque strength available al series K according to standard DIN ISO C1 K...M-06 CL Simple assembly due to the hexagonal body and the integrated lock nut. h1 m h2 h3 d3 l1 l2 2nd Generation Thread L = left-hand thread R = right-hand thread Housing (female thread) al series K W Spherical ball: iglidur W300 page 819 More ball materials on request page 815 Part number Max. static tensile strength Max. static radial load Min. thread Max. torque strength Max. torque through ball Weight Right-hand Left-hand Short term Long term Short term Long term depth Thread Inner threading Standard without MH Standard with MH thread thread [N] [N] [N] [N] [mm] [Nm] [Nm] [Nm] [g] KRM-06 CL KLM-06 CL 1, KRM-08 CL KLM-08 CL 2,100 1, KRM-10 CL KLM-10 CL 3,100 1, Part number d3 W C1 h3 h1 h2 l1 l2 m Max. E10 without with pivot angle Right-hand Left-hand MH MH thread thread ±0.2 KRM-06 CL KLM-06 CL M06 SW KRM-08 CL KLM-08 CL M08 SW KRM-10 CL KLM-10 CL M10 SW Rod ends can be ordered in metric dimensions with metal insert with the addition of MH after the part numbers listed here. Example: KRM-10 CL MH (Inner-Ø: 10 mm). For another bearing material than iglidur W300, please add J or R to the part number. Example: KRM-10 CL J. Spherical ball materials to choose page 815 RKM: low-cost JKM: low moisture absorption W300: standard bearing with metal sleeve J4KM: low-cost and low moisture absorption Life calculation, CAD files and much more support 723

11 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends with female thread: KCRM and KCLM Rod ends with female thread: KCRM and KCLM Smooth design has no dirt traps Spherical ball is clipped in Choice of iglidur ball materials C1 KC...M-06 Compensation of misalignment Excellent corrosion resistance Design with metal sleeve for higher torque strength available al series K according to I2 h1 Thread L = left-hand thread R = right-hand thread standard DIN ISO l1 Housing (female thread) al series K d3 W Spherical ball: iglidur W300 page 819 More ball materials on request page 815 Part number Right-hand Left-hand Max. static tensile strength Short term Long term Max. static radial load Short term Long term Max. torque Max. torque Weight strength through balls Inner threading without MH thread thread [N] [N] [N] [N] [Nm] [Nm] [Nm] [g] KCRM-05 KCLM-05 New! 1, KCRM-06 KCLM-06 1, KCRM-08 KCLM-08 2,100 1, KCRM-10 KCLM-10 3,100 1, KCRM-10-F KCLM-10-F New! 3,100 1, KCRM-12 KCLM-12 New! 3,560 1, KCRM-12-F KCLM-12-F New! 3,560 1, KCRM-16 KCLM-16 New! 3,800 1, KCRM-16-F KCLM-16-F New! 3,800 1, KCRM-20 KCLM-20 New! 4,550 2, KCRM-20-M20 KCLM-20-M20 New! 4,550 2, with MH Part number d3 W C1 h1 l1 l2 Max. without with pivot angle Right-hand Left-hand MH MH thread thread ± 0.2 KCRM-05 KCLM-05 New! M5 SW KCRM-06 KCLM M06 SW KCRM-08 KCLM M08 SW KCRM-10 KCLM M10 SW KCRM-10-F KCLM-10-F New! M10x1.25 SW KCRM-12 KCLM-12 New! M12 SW KCRM-12-F KCLM-12-F New! M12x1.25 SW KCRM-16 KCLM-16 New! M16 SW KCRM-16-F KCLM-16-F New! M16x1.5 SW KCRM-20 KCLM-20 New! M20x1.5 SW KCRM-20-M20 KCLM-20-M20 New! M20x2.5 SW Rod ends can be ordered in metric dimensions with metal insert with the addition of MH after the part numbers listed here. Example: KCRM-10 MH (Inner-Ø: 10 mm). Spherical ball materials to choose page 815 RKM: low-cost JKM: low moisture absorption W300: standard bearing with metal sleeve J4KM: low-cost and low moisture absorption Life calculation, CAD files and much more support 725

12 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends with male thread: KARM and KALM Rod ends with male thread: KARM and KALM Standard design Design with metal sleeve (MH) Maintenance-free, self-lubricating High strength ander impact loads Very high tensile strength for varying loads Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-restistant High vibration dampening capacity Suitable for rotating, oscillating, and linear movements al series K according to standard DIN ISO Available with metal sleeve for higher torque I2 h1 d3 C1 I1 KA M-05 Thread L = left-hand thread R = right-hand thread Housing (male thread) al series K Spherical ball: iglidur W300 page 819 Part number Max. static tensile strength Max. static radial load Min. thread depth Max. torque strength Max. torque through ball Weight Right-hand Left-hand Short Long Short Long Outer without MH with MH Thread term term term term threading thread thread [N] [N] [N] [N] [mm] [Nm] [Nm] [Nm] [g] KARM-05 KALM KARM-06 KALM-06 1, KARM-08 KALM-08 1, KARM-10 KALM-10 2,500 1, KARM-10 F KALM-10 F 2,500 1, KARM-12 KALM-12 2,700 1, KARM-12 F KALM-12 F 2,700 1, KARM-14 KALM-14 3,400 1, KARM-16 KALM-16 3,900 1, KARM-16 F KALM-16 F 3,900 1, KARM-18 KALM-18 4,200 2,100 1, KARM-20 KALM-20 6,000 3,000 1, KARM-20 M20 KALM-20 M20 6,000 3,000 1, KARM-22 KALM-22 7,200 3,600 1, KARM-25 KALM-25 7,500 3,750 1, KARM-30 KALM-30 8,800 4,400 2,300 1, Part number d3 C1 h1 l1 l2 Max. pivot Right-hand Left-hand E10 without MH with MH angle thread thread ± 0.2 KARM-05 KALM M KARM-06 KALM M KARM-08 KALM M KARM-10 KALM M KARM-10 F KALM-10 F M10 x KARM-12 KALM M KARM-12 F KALM-12 F M12 x KARM-14 KALM M KARM-16 KALM M KARM-16 F KALM-16 F M16 x KARM-18 KALM M18 x KARM-20 KALM M20 x KARM-20 M20 KALM-20 M M20 x KARM-22 KALM M22 x KARM-25 KALM M24 x KARM-30 KALM M30 x For rod ends with metal insert please add MH to the part number. Example: KARM-10 MH (Inner-Ø: 10 mm) Life calculation, CAD files and much more support 727

13 rod ends Rod Ends Product Range My Sketches rod ends Rod ends, male thread; 2nd generation: KARM CL C1 KARM-06 CL I2 h1 I1 d3 2nd Generation Thread Housing (male thread) al series K Smooth design has no dirt traps Compensation of misalignment Excellent corrosion resistance Design with metal sleeve for higher torque strength available Left-hand thread version KALM in preparation al series K according to standard DIN ISO Spherical ball: iglidur W300 page 819 More ball materials on request page 815 Technical data Part number Max. static Max. Min. Max. torque Max. torque Weight tensile strength radial load thread depth strength through ball Outer without MH with MH Short term Long term Short term Long term Thread threading [N] [N] [N] [N] [mm] [Nm] [Nm] [Nm] [g] KARM-06 CL 1, KARM-08 CL 1, KARM-10 CL 2,500 1, KARM-12 CL 2,700 1, Part number d3 C1 h1 l1 l2 Max. E10 without MH with MH pivot angle ± 0.2 KARM-06 CL M KARM-08 CL M KARM-10 CL M KARM-12 CL M Rod ends can be ordered in metric dimensions with metal insert with the addition of MH after the part numbers listed here. Example: KARM-10 MH (Inner-Ø: 10 mm). For another bearing material please add J or R to the part number. Example: KARM-10 CL J. on request Life calculation, CAD files and much more support 729

14 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends with female thread: ERM and ELM Rod ends with female thread: ERM and ELM Maintenance-free, self-lubricating High strength under impact loads Very high tensile strength for varying loads C1 E M-04 Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant High vibration-dampening capacity Suitable for rotating, oscillating and linear movements l2 h1 l1 Thread L = left-hand thread R = right-hand thread Housing (female thread) al series E according to standard DIN ISO d4 d5 d3 W al series E 50 % higher tensile force possible due to metal inlay (only dimension 16, more dimensions on request) Spherical ball: iglidur W300 page 819 For temperatures up to +200 C we recommend More ball materials on request ERM-HT and ELM-HT page 734 page 815 Part number Max. static tensile strength Max. static radial load Min. thread depth Max. torque strength Max. torque Weight through ball Right-hand Left-hand Short term Long term Short term Long term Thread Inner threading thread thread [N] [N] [N] [N] [mm] [Nm] [Nm] [g] ERM-04 ELM ERM-05 ELM-05 1, ERM-06 ELM-06 1, ERM-08 ELM-08 2,000 1, ERM-10 ELM-10 2,300 1, ERM-10 F ELM-10 F 2,300 1, ERM-12 ELM-12 3,300 1, ERM-12 F ELM-12 F 3,300 1, ERM-15 ELM-15 4,800 2, ERM-16 ELM-16 5,000 2, ERM-16 F ELM-16 F 5,000 2, ERM-17 ELM-17 5,300 2,650 1, ERM-17 F ELM-17 F 5,300 2,650 1, ERM-20 ELM-20 7,200 3,600 1, ERM-20 M20 ELM-20 M20 7,200 3,600 1, ERM-25 ELM-25 10,000 5,000 2,600 1, ERM-30 ELM-30 10,500 5,250 3,000 1, Part number d3 d4 d5 C1 h1 l1 l2 W Max. Right-hand Left-hand E10 pivot thread thread angle ERM-04* ELM-04* 4 15 M SW08 33 ERM-05 ELM M SW09 33 ERM-06 ELM M SW11 27 ERM-08 ELM M SW14 24 ERM-10 ELM M SW17 24 ERM-10 F ELM-10 F M10 x SW17 24 ERM-12 ELM M SW19 21 ERM-12 F ELM-12 F M12 x SW19 21 ERM-15 ELM M SW22 21 ERM-16* ELM-16* M SW22 21 ERM-16 F* ELM-16 F* M16 x SW22 21 ERM-17 ELM M SW27 18 ERM-17 F ELM-17 F M16 x SW27 18 ERM-20 ELM M20 x SW30 16 ERM-20 M20 ELM-20 M M20 x SW30 16 ERM-25 ELM M24 x SW36 16 ERM-30 ELM M30 x SW41 13 * special form with hexagonal foot Spherical ball materials to choose page 815 J4VEM: clearance-free, preloaded JEM: low moisture absorption REM: low-cost J4EM: low-cost and low moisture absorption Life calculation, CAD files and much more support 731

15 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Rod ends with male thread: EARM and EALM Rod ends with male thread: EARM and EALM Maintenance-free, dry-running High stiffness Very high tensile strength for varying loads C1 EA M-05 Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant I2 Thread High vibration-dampening capacity h1 L = left-hand thread Suitable for rotating, oscillating, and linear movements I1 R = right-hand thread Housing (male thread) al series E according to al series E standard DIN ISO d3 For temperatures up to +200 C we recommend EARM-HT and EALM-HT page 735 Spherical ball: iglidur W300 page 819 More ball materials on request page 815 Part number Max. static tensile strength Max. static radial load Min. thread depth Max. torque strength Max. torque Weight through ball Right-hand Left-hand Short term Long term Short term Long term Thread Outer threading thread thread [N] [N] [N] [N] [mm] [Nm] [Nm] [g] EARM-05 EALM EARM-06 EALM EARM-08 EALM-08 1, EARM-10 EALM-10 2,600 1, EARM-10 F EALM-10 F 2,600 1, EARM-12 EALM-12 3,100 1, EARM-12 F EALM-12 F 3,100 1, EARM-15 EALM-15 3,400 1, EARM-17 EALM-17 3,600 1, EARM-17 F EALM-17 F 3,600 1, EARM-20 EALM-20 6,800 3,400 1, EARM-20 M20 EALM-20 M20 6,800 3,400 1, EARM-25 EALM-25 7,000 3,500 1, EARM-30 EALM-30 7,000 3,500 2,000 1, Part number d3 C1 h1 l1 l2 Max. Right-hand Left-hand E10 pivot angle thread thread EARM-05 EALM M EARM-06 EALM M EARM-08 EALM M EARM-10 EALM M EARM-10 F EALM-10 F M10 x EARM-12 EALM M EARM-12 F EALM-12 F M12 x EARM-15 EALM M EARM-17 EALM M EARM-17 F EALM-17 F M16 x EARM-20 EALM M20 x EARM-20 M20 EALM-20 M M20 x EARM-25 EALM M24 x EARM-30 EALM M30 x Spherical ball materials to choose page 815 J4VEM: clearance-free, preloaded JEM: low moisture absorption REM: low-cost J4EM: low-cost and low moisture absorption Life calculation, CAD files and much more support 733

16 rod ends Rod Ends Product Range Rod Ends Product Range rod ends High temperature rod ends with female thread: ERM-HT and ELM-HT High temperature rod ends with male thread: EARM-HT and EALM-HT C1 C1 E M-05-HT EA M-05-HT l2 h1 l1 High Temperature Thread L = left-hand thread I2 h1 I1 High Temperature Thread L = left-hand thread d4 d5 d3 W R = right-hand thread Housing (female thread) al series E d3 R = right-hand thread Housing (male thread) al series E For temperatures up to +200 C For temperatures up to +200 C Maintenance-free, self-lubricating Housing: iguton G page 1267 Maintenance-free, self-lubricating Housing: iguton G page 1267 High strength under impact loads Spherical ball: iglidur X page 821 High strength under impact loads Spherical ball: iglidur X page 821 Very high tensile strength for varying loads Very high tensile strength for varying loads Compensation of misalignment Compensation of misalignment Compensation of edge loads Compensation of edge loads Insensitive to dirt, dust and lint Insensitive to dirt, dust and lint Corrosion- and chemical-resistant Corrosion- and chemical-resistant (Chemical table page 1258 ) (Chemical table page 1258 ) For underwater applications For underwater applications Suitable for rotating, oscillating and linear movements Suitable for rotating, oscillating and linear movements al series E according to standard al series E according to standard DIN ISO DIN ISO Part number d3 d4 d5 C1 h1 l1 l2 W Max. Weight Part number d3 C1 h1 l1 l2 Max. Weight E10 pivot angle [g] E10 pivot angle [g] Right-hand Left-hand Right-hand Left-hand thread thread ERM-05-HT ELM-05-HT 5 19 M SW ERM-06-HT ELM-06-HT 6 21 M SW ERM-08-HT ELM-08-HT 8 24 M SW ERM-10-HT ELM-10-HT M SW ERM-12-HT ELM-12 HT M SW Other dimensions available on request thread thread EARM-05-HT EALM-05-HT 5 19 M EARM-06-HT EALM-06-HT 6 21 M EARM-08-HT EALM-08-HT 8 24 M EARM-10-HT EALM-10-HT M EARM-12-HT EALM-12-HT M Other dimensions available on request Life calculation, CAD files and much more support 735

17 rod ends Rod Ends Product Range Inch Rod Ends Product Range Inch rod ends Rod ends with female thread: KRI and KLI Rod ends with female thread: KRI and KLI Maintenance-free, self-lubricating C1 High strength under impact loads Very high tensile strength for varying loads K I-03 Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant High vibration-dampening capacity Suitable for rotating, oscillating, and h1 l2 l1 Inch Thread L = left-hand thread R = right-hand thread linear movements Housing (female thread) d4 d3 al series K W Spherical ball: iglidur W300 page 819 Part number Max. static tensile strength Max. radial load Min. thread depth Max. torque strength Right-hand Left-hand Short term Long term Short term Long term Thread Inner threading Max. Weight torque through ball thread thread [N] [N] [N] [N] [Inch] [Nm] [Nm] [g] KRI-03 KLI KRI-04 KLI-04 1, KRI-05 KLI-05 1, KRI-06 KLI-06 2,000 1,000 1, KRI-07 KLI-07 2,300 1,150 1, KRI-08 KLI-08 2,600 1,300 1, KRI-10 KLI-10 4,900 2,450 1, KRI-12 KLI-12 5,600 2,800 2,300 1, KRI-16 KLI-16 6,000 3,000 2,600 1, s [Inch] Part number d3 d4 C1 h1 l1 l2 W Max. E10 pivot Right-hand Left-hand angle thread thread KRI-03 KLI KRI-04 KLI / KRI-05 KLI / KRI-06 KLI / KRI-07 KLI / KRI-08 KLI / KRI-10 KLI / KRI-12 KLI / KRI-16 KLI * 20 * Spanner flat design Life calculation, CAD files and much more support 737

18 rod ends Rod Ends Product Range Inch Rod Ends Product Range Inch rod ends Rod ends with male thread: KARI and KALI Rod ends with male thread: KARI and KALI Maintenance-free, self-lubricating C1 High strength under impact loads Very high tensile strength for varying loads KA I-03 Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Inch Corrosion- and chemical-resistant l2 Thread High vibration-dampening capacity h1 L = left-hand thread Suitable for rotating, oscillating, and l1 R = right-hand thread linear movements Housing (male thread) al series K d3 Spherical ball: iglidur W300 page 819 Part number Max. static Max. Min. Max. Max. Weight tensile strength radial thread torque torque load depth strength through ball Right-hand Left-hand Short term Long term Short term Long term Outer threading thread thread [N] [N] [N] [N] [Inch] [Nm] [Nm] [g] KARI-03 KALI KARI-04 KALI KARI-05 KALI-05 1, KARI-06 KALI-06 1, KARI-07 KALI-07 2,000 1, KARI-08 KALI-08 2,500 1, KARI-10 KALI-10 3,500 1, KARI-12 KALI-12 3,900 1,950 1, KARI-16 KALI-16 4,400 2,200 1, s [Inch] Part number d3 C1 h1 l1 l2 Max. Right-hand Left-hand E10 pivot angle thread thread KARI-03 KALI KARI-04 KALI / KARI-05 KALI / KARI-06 KALI / KARI-07 KALI / KARI-08 KALI / KARI-10 KALI / KARI-12 KALI / KARI-16 KALI Life calculation, CAD files and much more support 739

19 rod ends Rod Ends Product Range Inch Rod Ends Product Range Inch rod ends Rod ends with female thread: ERI and ELI Rod ends with female thread: ERI and ELI Maintenance-free, self-lubricating High strength under impact loads Very high tensile strength for varying loads C1 E I-03 Compensation of misalignment Compensation of edge loads Insensitive to dirt, dust and lint Corrosion- and chemical-resistant High vibration-dampening capacity Suitable for rotating, oscillating and linear movements l2 h1 l1 Inches Thread L = left-hand thread R = right-hand thread Housing (female thread) d4 d5 d3 W al series E Spherical ball: iglidur W300 page 819 Part number Max. static tensile strength Max. radial load Min. thread depth Max. torque strength Max. torque through Weight Short term Long term Short term Long term Thread Inner threading ball Right-hand Left-hand [N] [N] [N] [N] [Inch] [Nm] [Nm] [g] thread thread ERI-03 ELI-03 1, ERI-04 ELI-04 1, ERI-05 ELI-05 2,000 1, ERI-06 ELI-06 2,300 1, ERI-07 ELI-07 3,300 1, ERI-08 ELI-08 3,300 1, ERI-10 ELI-10 5,000 2, ERI-12 ELI-12 7,200 3,600 1, s [Inch] Part number d3 d4 d5 C1 Right-hand Left-hand E10 thread thread ERI-03 ELI ERI-04 ELI / ERI-05 ELI / ERI-06 ELI / ERI-07 ELI / ERI-08 ELI / ERI-10* ELI-10* / ERI-12 ELI / Part number h1 I1 I2 W Max. Right-hand Left-hand E10 pivot angle thread thread ERI-03 ELI ERI-04 ELI ERI-05 ELI ERI-06 ELI ERI-07 ELI ERI-08 ELI ERI-10* ELI-10* ERI-12 ELI * ERI-10/ELI-10 special form with hexagonal foot Life calculation, CAD files and much more support 741

20 rod ends Rod Ends Product Range Rod Ends Product Range rod ends Angled ball and socket joint: WGRM and WGLM a b Connection for rotating and pivoting movements and robust Easy and quick assembly Vibration-dampening Insensitive to dirt and dust all stud made of plastic or metal* S1 WG...M-05 WG...M-05 LC h1 d4 Ø Thread L = left-hand thread R = right-hand thread Housing Angled ball Spherical cap: iglidur W300 page 819 l5 e Angled ball and socket joint (low-cost): WGRM LC and WGLM LC Low-cost Thread L = left-hand thread R = right-hand thread s as WGRM Angled ball Housing with ball stud Low weight Maintenance-free all stud made of plastic or metal* h3 h2 I6 I2 I1 S1 S2 Part number Max. axial Max. axial Max. axial Max. axial tensile Weight tensile force compressive force tensile force force in housing axis, (all stud axis*) (all stud axis) (Housing axis) with metal ball stud Right-hand Left-hand Short term Long term Short term Long term Short term Long term Short term Long term thread thread [N] [N] [N] [N] [N] [N] [N] [N] [g] WGRM-05 WGLM WGRM-06 WGLM WGRM-08 WGLM , WGRM-10 WGLM , * For a metal stud please add the suffix MS. Example: WGRM-05 MS Part number d4 l1 l2 l5 l6 h1 h2 h3 a b e S1 S2 Max. Right-hand Left-hand pivot thread thread Min angle WGRM-05 WGLM M SW 8 SW 7 25 WGRM-06 WGLM M SW 9 SW 8 25 WGRM-08 WGLM M SW12 SW11 25 WGRM-10 WGLM M SW14 SW13 25 Part number Max. axial Max. axial Max. axial Max. axial tensile Weight tensile force (all stud axis*) compressive force (all stud axis) tensile force (Housing axis) force in housing axis, with metal ball stud Right-hand Left-hand Short term Long term Short term Long term Short term Long term Short term Long term thread thread [N] [N] [N] [N] [N] [N] [N] [N] [g] WGRM-05 LC WGLM-05 LC WGRM-06 LC WGLM-06 LC WGRM-08 LC WGLM-08 LC , WGRM-10 LC WGLM-10 LC , * For a metal stud please add the suffix MS. Example: WGRM-05 LC MS technical drawing page 742 Part number d4 l1 l2 l5 l6 h1 h2 h3 a b e S1 S2 Max. Right-hand Left-hand pivot thread thread Min angle WGRM-05 LC WGLM-05 LC 8.0 M SW 8 SW 7 25 WGRM-06 LC WGLM-06 LC 10.0 M SW 9 SW 8 25 WGRM-08 LC WGLM-08 LC 13.0 M SW 12 SW WGRM-10 LC WGLM-10 LC 16.0 M SW 14 SW Life calculation, CAD files and much more support 743

21 rod ends New in this catalog! Rod Ends Product Range Rod Ends Product Range rod ends all joint, now removable: WGRM-DE and WGLM-DE In-line ball and socket joint: AGRM and AGLM WG...M-05-DE AG...M-08 Cost-effective connection Very low weight Absolute corrosion-resistance Easy assembly (75 N) and disassembly High holding forces in the assembled condition (260 N) Disassembly Thread L = left-hand thread R = right-hand thread Housing Angled ball all stud: galvanised steel d4 S1 e Thread L = left-hand thread R = right-hand thread In-line ball Spherical cap: iglidur W300 page 819 e l5 a l2 Ø l1 h1 h1 d4 h3 b S1 b a l3 l1 l2 h3 S2 ø For all mechanical combinations Very easy hand assembly Maintenance-free operation Corrosion-and chemical-resistant Good vibration-dampening qualities all stud made of plastic or metal* l6 S2 Part number* d4 l1 l2 l5 l6 h1 h3 Right-hand Left-hand thread thread Min. Min WGRM-05-DE WGLM-05-DE New! 8.0 M WGRM-06-DE WGLM-06-DE New! 10.0 M Part number* S1 S2 a b e Weight Pivot angle Right-hand Left-hand thread thread [g] Recom. Max. WGRM-05-DE WGLM-05-DE New! SW9 SW WGRM-06-DE WGLM-06-DE New! SW11 SW Technical data Part number* Max. static axial tensile force Max. static axial compressive force Max. assembling force Weight Right-hand Left-hand Short term Long term Short term Long term thread thread [N] [N] [N] [N] [N] [g] AGRM-08 AGLM , * For a metal stud please add the suffix MS. Example: AGRM-08 MS Part number* d4 l1 l2 l3 h3 S1 S2 a b e Pivot angle Right-hand Left-hand thread thread Min Min. Recom. Max. AGRM-08 AGLM M SW12 SW Life calculation, CAD files and much more support 745

22 rod ends Rod Ends Product Range My Sketches rod ends In-line ball and socket joint: AGRM LC and AGLM LC AG...M-06 LC d4 S1 Low-cost Thread L = left-hand thread R = right-hand thread In-line ball e b a Housing with ball stud h3 Low weight l1 ø Maintenance-free all stud made of plastic or metal* l3 l2 S2 Part number Max. static axial tensile force Max. static axial compressive force Short term Long term Short term Long term Weight Right-hand Left-hand [N] [N] [N] [N] [g] thread thread AGRM-06 LC AGLM-06 LC ,000 1, * For a metal stud please add the suffix MS. Example: AGRM-06 LC MS Part number d4 l1 l2 l3 h3 S1 S2 a b e Pivot angle Right-hand Left-hand thread thread Min Min. Recom. Max. AGRM-06 LC AGLM-06 LC 10.0 M SW Life calculation, CAD files and much more support 747

23 rod ends Rod Ends Product Range clevis joints Adapter bolt: PKRM and PKLM I4 PK M-05 I2 I1 I3 Thread L = left-hand thread d3 R = right-hand thread Series K Adapter bolt w POM page 1268 Solid polymer bolts with a hexagonal head are an accessory to the series K rod ends. The plain shank fits into the inside diameter of the ball and is secured by a circlip. The adapter bolts consist of highly shock-resistant, longfibre reinforced polymer POM. This component effectively transforms a standard K series rod end into a ball and socket joint. Excellent corrosion resistance Designed for use with K series rod ends High strength under impact loads Vibration-dampening Easy to fit and Part number Max. static tensile strength Max. static radial load d3 l1 l4 l3 l2 W Weight Short Long Short Long Connection Total Length Thread Nut Width term term term term h11 Thread length adjusting length width across bolt Right-hand Left-hand [N] [N] [N] [N] flats [g] thread thread* PKRM-05 PKLM M PKRM-06 PKLM M PKRM-08 PKLM M PKRM-10 PKLM M PKRM-12 PKLM M PKRM-14 PKLM , M PKRM-16 PKLM , M PKRM-18 PKLM , M18 x PKRM-20 PKLM ,200 1, M20 x Clevis Joints High tensile strength Vibration-dampening Noise-dampening Can be used in combination with series E rod ends * Delivery : 4-6 weeks Life calculation, CAD files and much more support 749

24 clevis joints Clevis Joints Clevis Joints Application Examples clevis joints clevis joints are all made of igumid G to DIN 71752, which can be used in combination with series E rod ends. Available components are clevis joint, clevis pin and clip or as an alternative, springloaded pin. Typical sectors of industry and application areas Food industry Packaging Heavy Duty Automotive Renewable energy Automation etc. High tensile strength Vibration-dampening When to use it? If high stiffness is requested If corrosion resistance is required If no lubrication is to be used To save weight If maintenance-free, dry-running is required If simple assembly is required In combination with pneumatic cylinders and gas struts Improve technology and reduce costs 110 exciting examples online Noise-dampening Can be used in combination with series E rod ends When not to use it? If temperatures are higher than +200 C If diameters above 20 mm are required Temperature +80º Product range 4 types Ø 4 20 mm 30º Pneumatic cylinder 750 More information 751

25 clevis joints Clevis Joints Product Overview My Sketches clevis joints Clevis joint combinations Clevis joints with clevis pin and circlip GERMK GELMK Clevis joints with spring-loaded fixing clip GERMF GELMF Combination, easy to fit GERMKE GELMKE Combination, easy to fit GERMFE GELMFE page 756 page 757 page 758 page 759 Component parts High strength under impact loads GERM GELM Spring-loaded fixing clip Clevis pin and Circlip GM GEFM GSR from page 754 page 760 page 761 Detectable clevis joint from page Life calculation, CAD files and much more support 753

26 clevis joints Clevis Joints Product Range Clevis Joints Product Range clevis joints Clevis joint: GERM and GELM Clevis joint: GERM and GELM High strength under impact loads Corrosion resistance High tensile strength Can be used in combination with series E rod ends Vibration-dampening Noise-dampening Available in left- (GELM) and right-hand-thread (GERM) I2 h1 I1 b1 g GE M-04 Thread design L = left-hand thread R = right-hand thread al series E Clevis joint d3 a2 a1 igumid G page 1267 Part number Max. static Max. static Max. torque Weight tensile strength radial load strength Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [Nm] [g] GERM-04 M3.5 GELM-04 M GERM-04 GELM GERM-05 DIN M4 GELM-05 DIN M4 1, GERM-05 DIN M5 GELM-05 DIN M5 1, GERM-05 GELM-05 1, GERM-05 DIN M5 LS* GELM-05 DIN M5 LS* 1, GERM-06 GELM-06 1, GERM-06 LS* GELM-06 LS* 1, GERM-08 GELM-08 2,700 1, GERM-10 GELM-10 4,700 2, GERM-10 F GELM-10 F 4,700 2, GERM-12 GELM-12 5,700 2, GERM-12 F GELM-12 F 5,700 2, GERM-14 GELM-14 6,600 3,300 1, GERM-14 F GELM-14 F 6,600 3,300 1, GERM-15 GELM-15 3,200 1,600 1, GERM-16 GELM-16 7,500 3,750 1, GERM-16 F GELM-16 F 7,500 3,750 1, GERM-17 GELM-17 3,600 1,800 1, GERM-17 F GELM-17 F 3,600 1,800 1, GERM-20 GELM-20 9,500 4,750 3,000 1, GERM-20 M20 GELM-20 M20 9,500 4,750 3,000 1, * LS = longer shank Part number g a1 a2 b1 d3 I2 h1 I h Thread tolerance Right-hand thread Left-hand thread H GERM-04 M3.5 GELM-04 M M GERM-04 GELM M GERM-05 DIN M4 GELM-05 DIN M M GERM-05 DIN M5 GELM-05 DIN M M GERM-05 GELM M GERM-05 DIN M5 LS* GELM-05 DIN M5 LS* M GERM-06 GELM M GERM-06 LS* GELM-06 LS* M GERM-08 GELM M GERM-10 GELM M GERM-10 F GELM-10 F M10 x GERM-12 GELM M GERM-12 F GELM-12 F M12 x GERM-14 GELM M GERM-14 F GELM-14 F M14 x GERM-15 GELM M GERM-16 GELM M GERM-16 F GELM-16 F M16 x GERM-17 GELM M GERM-17 F GELM-17 F M16 x GERM-20 GELM M20 x GERM-20 M20 GELM-20 M M20 x * LS = longer shank Life calculation, CAD files and much more support 755

27 clevis joints Clevis Joints Product Range Clevis Joints Product Range clevis joints Clevis joints with clevis pin and circlip: GERMK and GELMK Clevis joints with spring-loaded fixing clip: GERMF and GELMF GE MK-04 GE MF-04 Clevis pin and circlip Spring-loaded fixing clip Thread design Thread design L = left-hand thread L = left-hand thread R = right-hand thread R = right-hand thread al series E Single piece design al series E Clevis joint Easy to assemble Clevis joint Corrosion resistance Easy assembly also in hard to reach locations High tensile strength Can be used in combination with series E rod ends Can be used in combination with series E rod ends igumid G page 1267 Corrosion-resistant and lightweight igumid G page 1267 Part number Max. static Max. static Weight tensile strength radial load Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERMK-04 M3.5 GELMK-04 M GERMK-04 GELMK GERMK-05 DIN M4 GELMK-05 DIN M GERMK-05 DIN M5 GELMK-05 DIN M GERMK-05 GELMK GERMK-05 DIN M5 LS* GELMK-05 DIN M5 LS* GERMK-06 GELMK-06 1, GERMK-06 LS* GELMK-06 LS* 1, GERMK-08 GELMK-08 2,100 1, GERMK-10 GELMK-10 3,000 1, GERMK-10 F GELMK-10 F 3,000 1, GERMK-12 GELMK-12 3,500 1, GERMK-12 F GELMK-12 F 3,500 1, GERMK-14 GELMK-14 6,100 3,050 1, GERMK-15 GELMK-15 2,800 1,400 1, GERMK-16 GELMK-16 7,000 3,500 1, GERMK-16 F GELMK-16 F 7,000 3,500 1, GERMK-17 GELMK-17 3,600 1,800 1, GERMK-17 F GELMK-17 F 3,600 1,800 1, GERMK-20 GELMK-20 9,000 4,500 3,000 1, GERMK-20 M20 GELMK-20 M20 9,000 4,500 3,000 1, * LS = longer shank Single components: clevis pin GM and circlip GSR page 761 Part number Max. static tensile strength Max. static radial load Weight Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERMF-04 M3.5 GELMF-04 M GERMF-04 GELMF GERMF-05 DIN M4 GELMF-05 DIN M GERMF-05 DIN M5 GELMF-05 DIN M GERMF-05 DIN M5 LS* GELMF-05 DIN M5 LS* GERMF-05 GELMF GERMF-06 GELMF-06 1, GERMF-06 LS* GELMF-06 LS* 1, GERMF-08 GELMF-08 2,100 1, GERMF-10 GELMF-10 3,000 1, GERMF-10 F GELMF-10 F 3,000 1, GERMF-12 GELMF-12 3,500 1, GERMF-12 F GELMF-12 F 3,500 1, GERMF-16 GELMF-16 7,000 3,500 1, GERMF-16 F GELMF-16 F 7,000 3,500 1, * LS = longer shank Single components: spring-loaded fixing clip GEFM page Life calculation, CAD files and much more support 757

28 clevis joints Clevis Joints Product Range Clevis Joints Product Range clevis joints Clevis joints combination: GERMKE and GELMKE Clevis joints combination: GERMFE and GELMFE GE MKE-05 GE MFE-05 With clevis pin, circlip With spring-loaded and rod end fixing clip and rod end Thread design Thread design L = left-hand thread L = left-hand thread R = right-hand thread R = right-hand thread al series E al series E Clevis joint Clevis joint Corrosion resistance High tensile strength Can be used in combination with series E rod ends igumid G page 1267 igumid G page 1267 Part number Max. static Max. static Weight Part number Max. static Max. static Weight tensile strength radial load tensile strength radial load Short term Long term Short term Long term Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERMKE-05 GELMKE GERMKE-06 GELMKE-06 1, GERMKE-08 GELMKE-08 2,000 1, GERMKE-10 GELMKE-10 2,300 1, GERMKE-10 F GELMKE-10 F 2,300 1, GERMKE-12 GELMKE-12 3,300 1, GERMKE-12 F GELMKE-12 F 3,300 1, GERMKE-15 GELMKE-15 2,800 1, GERMKE-16 GELMKE-16 5,000 2, GERMKE-16 F GELMKE-16 F 5,000 2, GERMKE-17 GELMKE-17 3,600 1,800 1, GERMKE-17 F GELMKE-17 F 3,600 1,800 1, GERMKE-20 GELMKE-20 7,200 3,600 1, GERMKE-20 M20 GELMKE-20 M20 7,200 3,600 1, Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERMFE-05 GELMFE GERMFE-06 GELMFE-06 1, GERMFE-08 GELMFE-08 2,000 1, GERMFE-10 GELMFE-10 2,300 1, GERMFE-10 F GELMFE-10 F 2,300 1, GERMFE-12 GELMFE-12 3,300 1, GERMFE-12 F GELMFE-12 F 3,300 1, GERMFE-16 GELMFE-16 5,000 2, GERMFE-16 F GELMFE-16 F 5,000 2, Clevis joints with spring-loaded fixing clip can be used in combination with series E rod ends ERM and EARM page Clevis joints with spring-loaded fixing clip can be used in combination with series E rod ends ERM and EARM page Life calculation, CAD files and much more support 759

29 clevis joints Clevis Joints Product Range Clevis Joints Product Range clevis joints Spring-loaded fixing clip: GEFM Clevis pin: GM a b C I m I2 h1 l1 igumid G page 1267 d3 I1 igumid G page 1267 Part number d3 I l1 m Clip Weight Part number a b C l1 h1 l2 Weight h11 ±0.5 [g] GEFM GEFM-05 DIN GEFM-05 DIN M5 LS* GEFM GEFM-06 LS* GEFM GEFM GEFM GEFM GEFM * LS = longer shank h11 [g] GM GSR GM GSR GM-05 DIN GSR GM GSR GM GSR GM GSR GM GSR GM GSR GM GSR GM GSR GM GSR GM GSR Circlip: GSR POM page 1268 b Part number b Weight [g] GSR GSR GSR GSR GSR GSR GSR Life calculation, CAD files and much more support 761

30 clevis joints My Sketches pillow block bearings Pillow lock earings Maintenance-free, dry-running High tensile strength High endurance strength Lubrication-free Chemical-resistant High radial loads 762 Life calculation, CAD files and much more support 763

31 pillow block bearings Pillow lock earings Pillow lock earings Application Examples pillow block bearings pillow block bearings are bearing units especially easy to install and which are able to compensate alignment errors and prevent edge loads. Maintenance-free, dry-running High stiffness High strength Maintenance-free, self-lubricating When to use it? If chemical resistance is required If a cost-effective option is requested If you need dirt-resistant bearings To adjust misalignment If you need split components When not to use it? If temperatures are higher than +80 C If an integrated fixing collar is required If diameters above 50 mm are required If rotation speeds higher than 0.5 m/s are required Typical sectors of industry and application areas Plant design Machine building Packaging etc. Improve technology and reduce costs 110 exciting examples online Can be used in liquid media High radial loads Stone processing Temperature +80º Product Range 8 types Ø 5 50 mm 30º Paper industry More information 765

32 pillow block bearings Pillow lock earings Pillow lock earings Product Overview pillow block bearings Advantages Maintenance-free, dry running High stiffness High strength under impact loads Compensation for alignment errors Compensation for edge loads Corrosion-free Chemically resistant Vibration damping Suitable for rotating, oscillating and linear movements High radial loads Can be used in liquid media Space-saving design Easy to install Predictable life Maintenance-free, lubrication-free Areas of Application The ability to pivot allows pillow block bearings to compensate for misalignment and possible shaft deflection. Applications in which these effects cannot be prevented are suitable for pillow block bear ings. Tolerances Maintenance-free pillow block bear ings are designed with an inside diameter toler ance of E10. The shaft should be made to tolerance class h6 to h9. These recom mend ed tolerances allow for changes in the bearing due to temperature. Fitting pillow block bearings are designed for mounting with 2 bolts. Precision mount ing of the bearing is not necessary, since the ball compensates for alignment errors. Pillow lock earings For small space envelope Easy to dis assemble, split housing and ball Series K KSTM-GT Easy to fit ESTM page 770 page 771 page 772 New! New! For quick assembly and low moisture absorption ESTM-GT...-GT Product Range pillow block bearings are available in the dimensional series K and E for shaft diameters from 5 to 50 mm. The dimensional series K is available in imperial dimensions. More dimensions on request. Split housing with parallel bore ESTM-GT For diameters up to 150 mm ESTM-GT150 Extremely light, compact design ESTM-SL page 773 page 774 page 775 Pivot angle Pillow lock earings Standard design α Compensation of misalignment errors Series K KSTM Compensation of misalignment errors, inch dimensions Series K KSTI Adapter for dimensional series E page 768 page 768 page Life calculation, CAD files and much more support 767

33 pillow block bearings Pillow lock earing Product Range Pillow lock earing Product Range pillow block bearings Pillow block bearing KSTM and KSTI Pillow block bearing KSTM and KSTI Maintenance-free, dry-running High stiffness High strength under impact loads h2 KSTM-05 Compensation of misalignment and edge loads Corrosion- and chemical-resistant h1 h3 High vibration-dampening Suitable for rotating, oscillating and linear movements m a Pillow block bearing al series K C1 x2 Spherical ball: iglidur W300 page 819 Part number Max. static tensile strenght Max. axial static Max. torque for Weight Short term Long term compressive strength longitudinal holes [N] [N] [N] [Nm] [g] KSTM KSTM-06 1, KSTM-08 1, KSTM-10 1, KSTM-12 2,200 1, KSTM-14 2,400 1, KSTM-16 3,000 1,500 1, KSTM-18 3,500 1,750 1, KSTM-20 4,700 2,350 1, KSTM-22 6,100 3,050 1, KSTM-25 6,600 3,300 1, KSTM-30 8,100 4,050 2, Part number Max. static tensile strenght Max. axial static Max. torque for Weight Short term Long term compressive strength longitudinal holes [N] [N] [N] [Nm] [g] KSTI KSTI KSTI KSTI-06 1, KSTI-07 1, KSTI-08 1, KSTI-10 2,100 1, KSTI-12 3,100 1,550 1, KSTI-16 5,400 2,700 1, The maximum torques for longitudinal holes correspond to the permissible torque of the fixing screws (fixing category 5.8). Part number C1 h1 h2 m a h3 X2 Max. pivot E10 KSTM KSTM KSTM KSTM KSTM KSTM KSTM KSTM KSTM KSTM KSTM KSTM s [Inch] Part number C1 h1 h2 m a h3 X2 Max. pivot E10 KSTI º KSTI º KSTI º KSTI º KSTI º KSTI º KSTI º KSTI º KSTI º angle angle 768 Life calculation, CAD files and much more support 769

34 pillow block bearings Pillow lock earing Product Range Pillow lock earing Product Range pillow block bearings Pillow block bearing with split housing: KSTM-GT Pillow block bearing ESTM C1 h2 Part number d3 (2x) Fitting is easy and does not require shaft removal Maintenance-free, dry-running For high static loads Space- and weight-saving design Max. radial tensile strength KSTM-GT40-GT Max. axial tensile strength Short term Long term Short term Long term through ball Max. torque fixing holes Weight [N] [N] [N] [N] [Nm] [Nm] [g] KSTM-GT35* 11,000 5,500 2,500 1, KSTM-GT40 11,000 5,500 2,500 1, KSTM-GT40-GT** 11,000 5,500 2,500 1, KSTM-GT45* 15,000 7,500 3,000 1, KSTM-GT50 15,000 7,500 3,000 1, KSTM-GT50-GT** 15,000 7,500 3,000 1, Part number d3 h h1 h2 SW a m C1 Max. pivot E10 KSTM-GT35* KSTM-GT KSTM-GT40-GT** KSTM-GT45* KSTM-GT KSTM-GT50-GT** * Diameter given by iglidur J bore reducer; ** Split pillow block with split ball m a h1 sw h1 h Mounting: M12 High stiffness and fatigue strength Predictable life Split ball Inner diameter Split pillow block Pillow block bearing al series K Housing: RN33 page 1268 Spherical ball: iglidur J page 822 al series K accord. to standard DIN ISO angle R1 h2 m a d3 C1 High radial loads Can be used in liquid media Part number Max. radial tensile strength h h1 ESTM-08 Pillow block bearing al series E Spherical ball: iglidur W300 page 819 Space-saving design, easy to fit Predictable life Maintenance-free, self-lubricating al series E acc. to standard DIN ISO Adapter available page 776 Max. radial compressive strength Max. axial strength Max. torque fixing holes Weight Short term, [N] Long term, [N] Short term, [N] Long term, [N] Short term, [N] Long term, [N] [Nm] [g] ESTM-08 2,500 1,250 4,300 2, ESTM-10 3,400 1,700 5,300 2, ESTM-12 4,500 2,250 6,500 3, ESTM-16 6,700 3,350 8,500 4,250 1, ESTM-20 8,500 4,250 11,000 5,750 1, ESTM-25 13,500 6,750 18,500 9,250 2,300 1, ESTM-30* 10,000 5,000 16,500 8,250 2,500 1, * Due to the different manufacturing method, the load values are lower than 25mm diameter Part number, E10 d3 h h1 h2 a m C1 R1 Max. pivot angle ESTM ESTM ESTM ESTM ESTM ESTM ESTM Spherical ball materials to choose page 815 J4VEM: JEM: low REM: J4EM: low-cost clearance-free, moisture low-cost and low moisture preloaded absorption absorption 770 Life calculation, CAD files and much more support 771

35 pillow block bearings Pillow lock earing Product Range New in this catalog! Pillow lock earing Product Range pillow block bearings Pillow block bearing with split housing and split ball: ESTM-GT -GT Pillow block bearing with parallel bore: ESTM-GT ESTM-GT16-GT ESTM-GT16-25 m h1 h Split ball Split Pillow block bearing al series E Diameter Split Pillow block bearing al series E R1 C1 Housing: RN33 page 1268 Spherical ball: iglidur J page 822 m C1 h1 h igumid G page 1267 h2 a d3 Save during assembly and disassembly of shafts Low installation space and low weight High stiffness and fatigue strength Spherical ball material iglidur J for low moisture absorption Ideal for outdoor use al series E according to standard DIN ISO Adapter available page 776 R1 h2 a d3 Easy to assemble/disassemble Ideal for outdoor applications High loads al series E according to standard DIN ISO Part number max. static radial load max. static radial compressive force Weight Short term Long term Short term Long term [N] [N] [N] [N] [g] ESTM-GT16-GT 2,500 1,250 4,000 2, ESTM-GT20-GT 3,500 1,750 6,000 3, ESTM-GT25-GT 5,000 2,500 7,000 3, ESTM-GT30-GT 5,500 2,750 10,000 5, Part number d3 h h1 h2 a m C1 R1 Weight E10 [g] ESTM-GT16-25 New! ESTM-GT20-30 New! ESTM-GT25-35 New! ESTM-GT30-40 New! Part number d3 h h1 h2 a m C1 R1 Max. pivot E10 angle ESTM-GT16-GT , ESTM-GT20-GT , ESTM-GT25-GT , ESTM-GT30-GT Life calculation, CAD files and much more support 773

36 pillow block bearings New in this catalog! Pillow lock earing Product Range Pillow lock earings Product Range pillow block bearings Split pillow block bearing for diameters up to 150 mm: ESTM-GT 150 Pillow block bearing Slim line: ESTM SL ESTM-GT 150 ESTM-05 SL Diameter Split Pillow block bearing al series E h1 C1 Slim line Pillow block bearing al series E iglidur GLW page 225 R1 h Spherical ball: iglidur J page 822 Individual diameters in 6 8 weeks Static loads up to 4 tons Reduce assembly up to 50 % Resistant to corrosion and chemicals al series E according to standard DIN ISO m a h2 Space saving Low-cost Predictable life Maintenance- and lubricant-free With M3 thread, e. g. ESTM-10-SL-M3 For self tapping screw with outer diameter 3.5 mm al series E according to standard DIN ISO Part number h h1 h2 a m R1 Weight E10 [g] ESTM-GT 150 New! Part number Max. radial tensile strength Max. radial compressive strength Max. lateral strength Max. axial strength Weight Short term Long term Short term Long term Short term Long term Short term Long term [N] [N] [N] [N] [N] [N] [N] [N] [g] ESTM-05 SL 1, , ESTM-06 SL 1, , ESTM-08 SL 1, , ESTM-10 SL 1, , , Part number h h1 h2 a m C1 R1 Max. pivot E10 angle ESTM-05 SL ESTM-06 SL ESTM-08 SL ESTM-10 SL Life calculation, CAD files and much more support 775

37 pillow block bearings Pillow lock earing Product Range flange bearings Adapter for pillow block bearings of series E AD-01-ESTM-20 L h1 Pillow block bearing al series E øm x J øm x Adapter R1 N A m N 1 Same dimensions as metal pillow blocks Fz Fd For pillow block bearings of series E (ESTM, ESTM-GT) Corrosion- and chemical-resistant Fa Fs Fits directly Space-saving Same screws as tradtional metallic versions Part number Max. radial tensile strength [Fz] Max. radial compressive strength [Fd] lateral strength [Fs] Max. axial strength [Fa] (Tension/pression) Weight Flange earings Short term Long term Short term Long term Short term Long term Short term Long term [N] [N] [N] [N] [N] [N] [N] [N] [g] AD-01-ESTM-20* 2,400 1,200 10,000 5,000 3,000 1,500 1, AD-01-ESTM-25** 2,400 1,200 10,000 5,000 3,000 1,500 1, AD-01-ESTM-30** 2,400 1,200 10,000 5,000 3,000 1,500 1, [mm] Part number for ESTM- L A R1 J h1 N N1 m Mx AD-01-ESTM-20* ESTM M8 AD-01-ESTM-25** ESTM M8 AD-01-ESTM-30** ESTM M10 * plastic ** aluminum Maintenance-free, dry-running High tensile strength High endurance strength Compensation of alignment errors Compensation of edge loads Life calculation, CAD files and much more support 777

38 flange bearings Flange earings Flange earings Application Examples flange bearings flange bearings have been developed for the support of both the centre and ends of shafts. Like all products, these bearings consist of an igumid G housing and an iglidur W300 ball. flange bearings are made to the dimensional series E and are offered with two or four mounting holes. Typical sectors of industry and application areas Plant design Automation Agricultural machines Machine building Food industry etc. Maintenance-free, dry-running High stiffness High strength under impact loads When to use it? If chemical resistance is required If a cost-effective option is requested If you need dirt-resistant bearings To adjust misalignment If you need split components Improve technology and reduce costs 110 exciting examples online Low installation space When not to use it? If temperatures are higher than +200 C HT Version, page If an integrated fixing collar is required If diameters above 50 mm are required If rotation speeds higher than 0.5 m/s are required Temperature Product Range +80º +200º 5 types Ø 4 50 mm Conveyor technique 30º 40º Standard High temperature (HT) Rotary-sorter More information 779

39 flange bearings Flange earings Flange earings Product Overview flange bearings General Properties Flange bearings have been developed for supporting the centre or ends of shafts. Like all products, these bearings consist of an igumid G housing and an iglidur W300 ball. flange bearings are made to the dimensional series E and are offered with two or four mounting holes. Flange earings For temperatures up to +80 C New! Areas of Application Since flange bearings are made for maintenancefree use, they are especially suitable for applications in which access to the bearing is limited, in moist or wet en viron ments or clean room environments. flange bearings are also found in electric brushes, awnings, conveyor technology, and bakery machines. Easy to install EFOM For higher radial load EFSM from page 782 from page 784 page 786 New! Universal and quick assembly Female thread GFSM-IG Installation flange bearings are designed for mounting with 2 or 4 bolts, depending on the design. The 2-hole types are provided with elongated holes, which allow easy and flexible installation. An exact positioning of the bear ing housing is not necessary, since the flange bearing compensates for alignment errors. Universal and quick assembly Male thread GFSM-AG page 787 page 788 High static load, split housing Series K KFSM-GT Pivot angle Flange earings For temperatures up to +200 C α Easy to install EFOM-HT For higher radial load EFSM-HT page 789 page Life calculation, CAD files and much more support 781

40 flange bearings Flange earings Product Range Flange earings Product Range flange bearings Flange bearing with 2 mounting holes: EFOM iglidur W300 highly wear resistant ball d Easy to install Compensation of misalignment errors EFOM-04 Corrosion-resistance N L Inner diameter Maintenance-free, self-lubricating 2 holes m h Flange bearing al series E A1 Ag Spherical ball: iglidur W300 page 819 Part number Maximum static axial load Maximum static radial load Maximum static torque Max. pivot angle Weight Short term Long term Short term Long term Holes [N] [N] [N] [N] [Nm] [g] EFOM EFOM EFOM EFOM , EFOM ,000 1, EFOM-12 1, ,200 1, EFOM-15 1, ,400 1, EFOM-16 1, ,800 1, EFOM-17 1, ,200 1, EFOM-20 1, ,500 2, EFOM-25 3,000 1,500 6,000 3, EFOM-30 3,500 1,750 6,500 3, Spherical ball materials to choose page 815 J4VEM: JEM: low REM: J4EM: low-cost clearance-free, moisture low-cost and low moisture preloaded absorption absorption Part number d h L m A1 Ag N E10 Length Width Hole pitch Height of plate Total height ore diameter d x l ± EFOM x 5.0 EFOM x 5.0 EFOM x 5.0 EFOM x 6.5 EFOM x 8.0 EFOM x 8.0 EFOM x 10.0 EFOM x 10.1 EFOM x 10.2 EFOM x 12.5 EFOM x 12.6 EFOM x 16.0 Standard tolerances: from 0.5 to 6 mm: ±0.1 mm over 6 to 30 mm: ±0.2 mm over 30 to 120 mm: ±0.3 mm Life calculation, CAD files and much more support 783

41 flange bearings Flange earings Product Range d Flange earings Product Range flange bearings Flange bearing with 4 mounting holes: EFSM N Spherical ball made from wear-resistant iglidur W300 Easy assembly Compensation of alignment errors Corrosion-resistant Maintenance-free, dry-running h m EFSM-04 Inner diameter 4 holes Flange bearing al series E Ag A1 Spherical ball: iglidur W300 page 819 d Part number Maximum static axial load Maximum static radial load Maximum static torque Max. pivot angle Weight Short term Long term Short term Long term Holes [N] [N] [N] [N] [Nm] [g] EFSM , EFSM , EFSM , EFSM , EFSM ,000 1, EFSM ,500 1, EFSM-15 1, ,000 1, EFSM-16 1, ,200 1, EFSM-17 1, ,400 1, EFSM-20 2,000 1,000 4,000 2, EFSM-25 2,400 1,200 5,600 2, EFSM-30 2,800 1,400 6,000 3, Spherical ball materials to choose page 815 J4VEM: JEM: low REM: J4EM: low-cost clearance-free, moisture low-cost and low moisture preloaded absorption absorption Part number d h m A1 Ag N E10 Width Hole pitch Height Total ore d ±0.1 of plate height EFSM EFSM EFSM EFSM EFSM EFSM EFSM EFSM EFSM EFSM EFSM EFSM Standard tolerances: from 0.5 to 6 mm: ±0.1 mm over 6 to 30 mm: ±0.2 mm over 30 to 120 mm: ±0.3 mm Life calculation, CAD files and much more support 785

42 flange bearings New in this catalog! Flange earings Product Range New in this catalog! Flange earings Product Range flange bearings Complete housing with ball stud, female thread: GFSM-...-IG Complete housing with ball stud, male thread: GFSM-...-AG GFSM-06-IG GFSM-06-AG Maintenance-free and corrosion-resistant Easy connection easy assembly Compensation of misalignments Ag A1 h m A1 Female thread 4 holes Flange Mounted all stud: galvanised steel* Ag Other ball stud materials on request h m Maintenance-free and corrosion-resistant Easy connection easy assembly Compensation of misalignments Ag A1 h m A1 Male thread 4 holes Flange Mounted Ag all stud: galvanised steel* Other ball stud materials on request l6 Tensile force l6 Compressive force l6 Tensile force Compressive force l6 Force test direction Force test direction S1 N S1 N S1 N Part number Max. axial tensile force Max. axial compressive force Weight Short term Long term Short term Long term [N] [N] [N] [N] [g] GFSM-06-IG New! GFSM-08-IG New! GFSM-10-IG New! , Part number Max. axial tensile force Max. axial compressive force Weight Short term Long term Short term Long term [N] [N] [N] [N] [g] GFSM-06-AG New! GFSM-08-AG New! GFSM-10-AG New! , Part number m h Ag A1 I6 N S1 Max. Part number m h Ag A1 I6 N S1 Max. pivot angle pivot angle GFSM-06-IG New! M SW11 32 GFSM-06-AG New! M SW8 32 GFSM-08-IG New! M SW14 40 GFSM-08-AG New! M SW11 34 GFSM-10-IG New! M SW17 34 GFSM-10-AG New! M SW13 40 * Stainless steel ball stud on request * Stainless steel ball stud on request Life calculation, CAD files and much more support 787

43 flange bearings Flange earings Product Range Flange earings Product Range flange bearings Flange bearing with 4 mounting holes and split housing: KFSM GT High-temperature flange bearing with 2 mounting holes: EFOM-HT N h m KFSM GT-35-A EFOM-06-HT Preassembled Option with plug-in feet Resistant to dirt Low installation space For high static loads High tensile strength and fatigue strength Predictable life Maintenance-free, dry-running Mounting: with plug-in feet M10 without plug-in feet M12 Example: KFSM-GT-40-A Part number Maximum static radial load Maximum static axial load Weight Short term Long term Short term Long term [N] [N] [N] [N] [g] KFSM-GT-35* 5,000 2,500 4,500 2, KFSM-GT-40 5,000 2,500 4,500 2, KFSM-GT-45* 6,000 3,000 5,000 2, KFSM-GT-50 6,000 3,000 5,000 2, Max. tightening torque for fixing: 30 Nm A1 dk dn Part number dn d3 dk A1 A2 m h N Max. E10 pivot angle KFSM-GT-35* KFSM-GT KFSM-GT-45* KFSM-GT A2 d3 Option with plug-in feet Inner diameter Split housing 4 holes Flange bearing al series K Housing: RN33 page 1268 Spherical ball: iglidur J page 822 N A1 For high temperatures up to +200 C Spherical ball made of high temperature resistant iglidur X Easy assembly Compensation for alignment errors Corrosion-resistance Maintenance-free, dry-running Chemical resistant (chemical table page 1258 ) Under-water use d m h Part number d h L m A1 Ag N Max. Weight E10 Length Width Hole pitch ±0.1 Height of plate Total height ore diameter d l pivot angle [g] EFOM-05-HT x EFOM-06-HT x EFOM-08-HT x EFOM-10-HT x EFOM-12-HT x Other dimensions available on request Ag L High temperature s 2 holes Flange bearing al series E Housing: iguton G page 1267 Spherical ball: iglidur X page 821 For KFSM with distance pieces, please add an A to the part no. Example: KFSM-GT50-A. * Diameter given by iglidur J bore reducer Life calculation, CAD files and much more support 789

44 flange bearings Flange earings Product Range pressfit bearing High-temperature flange bearing with 4 mounting holes: EFSM-HT Ag A1 EFSM-05-HT d N High temperature 4 holes Flange bearing al series E h m Housing: iguton G page 1267 Spherical ball: iglidur X page 821 Ag A1 d For high temperatures up to +200 C Spherical ball made of high temperature resistant iglidur X Easy assembly Compensation for alignment errors Corrosion-resistance Maintenance-free, dry-running Chemical resistant (chemical table page 1258 ) Under-water use Part number d h m A1 Ag N Max. Weight E10 Width Hole pitch Height Total ore diameter pivot angle ±0.1 of plate height d [g] EFSM-05-HT EFSM-06-HT EFSM-08-HT EFSM-10-HT EFSM-12-HT Pressfit Spherical earings Easy to fit Extremely cost-effective Chemical-resistant High strength Other dimensions available on request Life calculation, CAD files and much more support 791

45 pressfit bearing Pressfit Spherical earings Pressfit Spherical earings Application Examples pressfit bearing The use of pivoting bearings is usually associated with high weight materials, difficult installation, and high costs. Most of the, maintenance is still necessary long term, and the bearings are only corrosion resistant in special designs. pressfit bearings put an end to all of these disadvantages: they are easy to fit, cost-effective, lightweight and robust. Typical sectors of industry and application areas Food industry Railway technology Automotive Plant design etc. Easy to fit Extremely cost-effective Chemical-resistant When to use it? For high axial and radial loads When an easy installation is required In case of reduced installation place If chemical resistance is required If a cost-effective option is requested If you need dirt-resistant bearings To adjust misalignment Improve technology and reduce costs 110 exciting examples online When not to use it? If temperatures are higher than +80 C If diameters above 30 mm are required If rotation speeds higher than 0.5 m/s are required High strength Temperature Product range +80º 13 types Ø 2 30 mm 30º Hose-skiving 792 More information 793

46 pressfit bearing Pressfit Spherical earings Pressfit Spherical earings Product Overview pressfit bearing Often roller bear ings or plain bearings malfunction prematurely due to high edge loads, or because they need to be readjusted, reamed, or re fitted in order to compensate for align ment errors. bearings put an end to all of these disadvantages and open up many new possibilities for your engineering design. easy to fit extremely cost-effective very low weight high strength Tolerances Maintenance-free pillow block bearings are designed with an inside diameter tolerance of E10. The shaft should be made to tolerance class h6 to h9. These recommended tolerances allow for changes in the bearing due to temperature. Installation bearings are pressfitted into a recommended H7 housing bore and axially secured. An exact orientation of the bear ing housing is not necessary, since the spheri cal bearing compensates for alignment errors. pressfit bearing Easy to fit, low-cost, selectable ball material Series K KGLM-LC Standard, easy to fit Series K KGLM For extremely narrow installation space Series K KGLM-SL Low tolerances Series K KGLM-H Standard, easy to fit, inch dimensions Series K KGLI page 797 page 796 page 798 page 799 page 800 Area of application Ease of installation makes many applications possible for bearings. They can be used anywhere. The self-aligning feature offers design advantages and helps to simplify assembly. s bearings are manufactured according to DIN ISO dimensional series K and E. The product range provides dimensions from 0.19 to 1.0 and from 2 to 30 mm. Please contact us if you need other dimensions. Pivot angle For small space requirement EGLM Cost-effective, selectable ball material EGLM-LC page 801 page 802 self-aligning clip bearing α Simply snapping into sheet metal ECLM For high axial and radial loads, selectable ball material ECLM-HD For tolerance compensation, selectable ball material EGFM-T page 803 page 804 page 805 double joint Solid polymer, selectable ball material EGZM Selectable ball stud Selectable ball and and tube materials, tube materials, individual dimensions individual dimensions and alignment and alignment WDGM KDGM page 806 page 808 page Life calculation, CAD files and much more support 795

47 pressfit bearing Pressfit Spherical earings Product Range Pressfit Spherical earings Product Range pressfit bearing Pressfit bearing: KGLM Pressfit bearing: KGLM Low Cost C Variety of ball materials Easy to install KGLM-02 Low-cost Split housing KGLM-05 LC Low Cost Pressfit bearing f 30 al series K C Pressfit bearing al series K Compensation of misalignment and edge loads Corrosion-resistant High dampening qualities Spherical ball: iglidur W300 page 819 Spherical balls: iglidur W300 page 819 High vibration-dampening capacity Other balls on request page 815 Suitable for rotating, oscillating and linear movements 30 f and Part number Max. static Max. torque C f Max. Weight compressive through ball E10 pivot angle strength radial axial* [N] [N] [Nm] [g] KGLM KGLM KGLM-05 1, KGLM-06 1, KGLM-08 2,700 1, KGLM-10 4,000 1, KGLM-12 5,400 1, KGLM-14 6,000 2, KGLM-16 8,000 3, KGLM-18 9,000 4, KGLM-20 10,000 5, KGLM-22 11,700 6, KGLM-25 13,600 7, KGLM-30 20,000 9, * The maximum static axial load is determined in a remote location hole. Part number Max. static compressive strength (short term) Weight radial axial* [N] [N] [g] KGLM-05 LC 1, KGLM-10 LC 4,000 1, KGLM-12 LC 5,400 1, KGLM-16 LC 8,000 3, KGLM-18 LC New! 9,000 4, KGLM-20 LC 10,000 5, KGLM-25 LC 13,600 7, KGLM-30 LC 20,000 9, * The maximum static axial load is determined in a remote location hole. Part number * C f Max. E10 pivot angle KGLM-05 LC KGLM-10 LC KGLM-12 LC KGLM-16 LC KGLM-18 LC New! KGLM-20 LC KGLM-25 LC KGLM-30 LC * pressfitted Life calculation, CAD files and much more support 797

48 pressfit bearing Pressfit Spherical earings Product Range Pressfit Spherical earings Product Range pressfit bearing Pressfit bearing: KGLM Slim Line Pressfit bearing: KGLM-H Soft Touch KGLM-08 SL KGLM-16 H Slim line Haptics f 30 Pressfit bearing C Pressfit bearing al series K al series K Spherical ball: iglidur W300 page 819 Spherical ball: iglidur L250 page max. 30 f Very small space, Quiet operation wall thickness 50 % thiner than KGLM compared Low tolerances to KGLM Easy to install Angle compensation up to 5 Chemical- and corrosion-resistant Low weight Compensation of misalignment errors, precise s according to DIN 1850 operation and Part number Max. static compressive Max. static compressive f Max. Weight strength (short term) strength (long term) E10 pivot angle radial axial radial axial [N] [N] [N] [N] [g] KGLM-08 SL 2, , KGLM-10 SL 4, , KGLM-12 SL 4, , KGLM-16 SL 6, , and Part number Max. static compressive Max. static compressive C f Max. Weight strength (short term) strength (long term) E10 pivot angle radial axial radial axial [N] [N] [N] [N] [g] KGLM-16-H 4, , Life calculation, CAD files and much more support 799

49 pressfit bearing Pressfit Spherical earings Product Range Pressfit Spherical earings Product Range pressfit bearing Pressfit bearing: KGLI Pressfit bearing: EGLM C C KGLI-03 EGLM-04 Inch Pressfit bearing Pressfit bearing f 30 al series K f 30 al series E Compensation of misalignment and edge loads Compensation of misalignment errors and edge loads Corrosion-resistant Corrosion-resistant High dampening qualities Spherical ball: iglidur W300 page 819 High dampening qualities Spherical ball: iglidur W300 page 819 Excellent vibration dampening Excellent vibration dampening Suitable for rotating, oscillating and linear movements Suitable for rotating, oscillat ing and linear movements and s [Inch] and Part number Max. static Max. torque C f Max. Weight compressive strenght through ball E10 pivot angle radial axial* [N] [N] [Nm] [g] KGLI-03 1, KGLI-04 1, KGLI-05 2, KGLI-06 2, KGLI-07 3, KGLI-08 4, KGLI-10 5, KGLI-12 8, KGLI-16 13,600 2, * The maximum static axial load is determined in a remote location hole. Part number Max. static Max. torque C f Max. Weight compressive strenght through ball E10 pivot angle radial axial* [N] [N] [Nm] [g] EGLM EGLM-05 1, EGLM-06 1, EGLM-08 1, EGLM-10 2, EGLM-12 3, EGLM-15 5,500 1, EGLM-16 6,000 1, EGLM-17 6,300 1, EGLM-20 9,000 1, EGLM-25 14,000 2, EGLM-30 17,000 4, * The maximum static axial load is determined in a remote location hole Life calculation, CAD files and much more support 801

50 pressfit bearing Pressfit Spherical earings Product Range Self-aligning Clip earing Product Range pressfit bearing Pressfit bearing: EGLM Low Cost Self-aligning clip bearing: ECLM Easy to install Low-cost b2 b1 Chemical- and corrosionresistant EGLM-15-LC ECLM Very tough Compensation of misalignment errors Low Cost metrisc d3 Sheet thickness Pressfit bearing Self-aligning clip bearing C al series E al series E Very easy installation by simply snapping into sheet metal Spherical ball: iglidur W300 page 819 Other balls on request page 815 No additional axial fastening necessary Extremely small installation space: space-saving, thin-walled design Spherical ball: iglidur J page f and Part number Max. static Max. torque C f Max. Weight compressive strenght through ball E10 pivot angle radial axial* [N] [N] [Nm] [g] EGLM-15-LC 5,500 1, EGLM-16-LC 6,000 1, EGLM-20-LC 9,000 1, EGLM-25-LC 14,000 2, EGLM-30-LC 17,000 4, * The maximum static axial load is determined in a remote location hole. Part number Max. static compressive strength (short term) Max. static compressive strength (long term) Weight radial axial radial axial [N] [N] [N] [N] [g] ECLM ECLM ECLM , ECLM , ECLM , ECLM , , Part number d3 Sheet metal b1 b2 Max. E10 ±0.2 thickness ±0.1 pivot y angle ECLM ECLM ECLM ECLM ECLM ECLM Life calculation, CAD files and much more support 803

51 pressfit bearing Self-aligning Clip earing Product Range Self-aligning Clip earing Product Range pressfit bearing Self-aligning clip bearing: ECLM-HD Self-aligning clip bearing: EGFM-T ECLM HD EGFM-08 T Heavy Duty Tolerance compensation Sheet thickness Inner diameter b2 Self-aligning bearing d3 y Self-aligning clip bearing al series E min. max. with flange al series E Spherical balls: iglidur W300 page 819 Other balls on request page 815 d3 C Spherical balls: iglidur W300 page 819 Other balls on request page 815 High axial and radial loads Adjustment of axial and radial clearance by preloading Easily clips into sheet metal No additional axial fastening necessary For sheet thickness 4 to 8 mm Maintenance-free, dry-running Easy to fit Max. tolerance compensation ±0.2 mm Part number Max. static compressive Max. static compressive Weight strength (short term) strength (long term) radial axial radial axial [N] [N] [N] [N] [g] ECLM HD New!* 1, ECLM HD 2, , ECLM HD New!* 3, , ECLM HD New!* 6, , Part number d3 y Max. E10 ±0.15 ±0.1 pivot angle ECLM HD New!* ECLM HD ECLM HD New!* ECLM HD New!* * in this catalog Spherical bearing materials to choose page 815 REM: low-cost JEM: low moisture absorption J4EM: lowcost and low moisture absorption J4VEM: clearance-free preloaded ball Part number Max. stat. compressive force (short term) Max. stat. compressive force (long term) Weight radial axial radial axial [N] [N] [N] [N] [g] EGFM-08 T SL* 1, EGFM-10 T 1, EGFM-12 T 2, , EGFM-16 T 6, , EGFM-20 T 9, , EGFM-25 T 14,000 2,800 7,000 1, EGFM-30 T 17,000 3,000 8,500 1, Part number d3 C b2 Housing Max. min. max. min. max. pivot angle EGFM-08 T SL* 8 (H10) EGFM-10 T 10 (E10) EGFM-12 T 12 (E10) EGFM-16 T 16 (E10) EGFM-20 T 20 (E10) EGFM-25 T 25 (E10) EGFM-30 T 30 (E10) * Spherical ball made of iglidur J Life calculation, CAD files and much more support 805

52 pressfit bearing Double Joint Product Range My Sketches pressfit bearing Double joint: EGZM c EGZM a x Pitch X Inner diameter Double joint al series E b Maintenance-free, self-lubricating Mechanical joining link between 2 components Compensation of misalignment errors Corrosion-resistant Double joint turned 90 available on request Spherical ball: iglidur W300 page 819 Other balls on request page 815 and Part number Max. static tensile Max. static tensile X b a c Max. Weight strength (short term) strength (long term) E10 pivot angle radial axial radial axial [N] [N] [N] [N] [g] EGZM ,100 1, EGZM , EGZM , EGZM ,100 1, EGZM , EGZM , EGZM ,100 1, EGZM , EGZM , EGZM ,000 3,500 1,500 1, EGZM ,000 1,900 1, EGZM ,500 3,500 1,250 1, EGZM ,500 2,300 1,250 1, EGZM ,500 1,900 1, EGZM ,000 3,500 1,000 1, EGZM ,500 1,900 1, Spherical bearing materials to choose page 815 REM: JEM: low J4VEM: J4EM: low-cost low-cost moisture clearance-free preloaded and low moisture absorption ball absorption Life calculation, CAD files and much more support 807

53 pressfit bearing Double Joint Product Range Double Joint Product Range pressfit bearing Variable double joint: WDGM Variable double joint: KDGM WDGM-05-A-SR-SZ KDGM-06-A-SR-J all stud material Spherical ball material SZ = Steel lank = iglidur W300 EZ = Stainless steel J = iglidur J PZ = igumid G J4 = iglidur J4 Tube material R = iglidur R SR = Steel EK = Stainless steel ER = Stainless steel Tube material all stud direction SR = Steel (A,, C or D) ER = Stainless steel Version A Version Version C Version D all stud thread Version A Version all stud direction (A or ) Double joint Angle Inner diameter Double joint al series K x d3 Spherical ball: igumid G, steel or stainless steel all stud: galvanised or stainless steel d3 x all: variable page 815 Socket cup M5, M6, M8 and M10 all stud: galvanised or stainless steel Individual centre dimensions and lengths R Individual alignment of the bearing position C all diameters 6, 8, 10 and 12 mm Individual centre dimensions and lengths Individual alignment of the bearing position h1 h2 S1 Part number d3 X h1 h2 S1 R Max. Width pivot angle min. across flats WDGM-05-A-SR-SZ * M SW WDGM-06-A-SR-SZ * M SW WDGM-08-A-SR-SZ * M SW WDGM-10-A-SR-SZ * M10** SW * Please add the required centre distance in mm. ** Housing s size 8 with a special M10 stud, available only in metal. Order example, WDGM-05-A-SR-SZ, 100 : Double joint with 05 ball stud thread, version A, tube material made of steel, ball stud made of steel, centre distance 100mm Part number d3 X C Max. pivot angle E 10 min. KDGM-06-A-SR-J * KDGM-08-A-SR-J * KDGM-10-A-SR-J * KDGM-12-A-SR-J * * Please add the required centre distance in mm. Order example, KDGM-06-A-SR-J, 100 : Double joint with 06 mm inner diameter, version A, tube material made of steel, ball made of iglidur J, centre distance 100mm Life calculation, CAD files and much more support 809

54 pressfit bearing My Sketches thrust bearings Spherical Thrust earings Easy to install Compensation of misalignment errors Compensation of edge loads Very good friction and wear properties 810 Life calculation, CAD files and much more support 811

55 thrust bearings Spherical Thrust earing Spherical Thrust earing thrust bearings self-aligning thrust bearings are very easy to fit and help to compensate misalignment errors and prevent edge loads. Easy to install Compensation of misalignment errors Prevent edge loads Very good friction and wear properties When to use it? If you want to save weight If corrosion resistance is requested If a bearing with a good coefficient of friction is sought When not to use it? At very high loads If temperatures are higher than +80 C If a high number of revolutions have to be achieved Mechanical Properties self-aligning thrust bearings are very easy to fit and help to compensate for alignment errors and prevent edge loads.the housing pad is made of the impact resistant, thermoplastic composite material igumid G. The washer is made of the iglidur W300 plain bearing material. This combination provides exceptionally good friction and wear properties. Loads The load capacity of thrust bearings is very high for standard ambient temperatures. For high continuous loads and high temperatures, the load capacity of the thrust bearings should be tested in an experiment that simulates the application. Coefficients of Friction and Speed Taking into account the radial load, maximum surface speeds up to 0.5 m/s rotating are possible. Installation The housing pad is installed so that it is countersunk and secured. The washer is loosely fitted in the socket and is held in place by the shaft that is placed into the bearing. Product Range thrust bearings are available in standard form to suit diameters from 5 to 20 mm. Please contact us if you require other dimensions. Temperature Product range +80º 1 type Ø 5 20 mm 30º 812 More information 813

56 thrust bearings Spherical Thrust earing Product Range balls Spherical thrust bearing: SAM SAM-05 Spherical washer Inner-Ø Type R1-all d 1 h1 Spherical washer: iglidur W300 page 151 Housing pad: igumid G page 1267 d 2 Housing pad h2 d 3 d 2 Part number Maximum static axial tensile strength short term Maximum static axial tensile strength long term Weight [N] [N] [g] SAM-05 4,000 2, SAM-06 5,000 2, SAM-08 8,000 4, SAM-10 10,000 5, SAM-12 12,000 6, SAM-16 17,000 8, SAM-20 22,000 11, Part number d3 h1 h2 H R1 Compensation washer housing pad washer housing pad total height radius angle DIN 7168 DIN 7168 SAM º SAM º SAM º SAM º SAM º SAM º SAM º * in assembled condition Spherical alls Maintenance-free, self-lubricating Corrosion-resistant High compressive strength High elasticity Different materials Life calculation, CAD files and much more support 815

57 balls Spherical alls Spherical alls Application Examples balls Every single iglidur material has its own special properties, which determines the suitability for your special applications and requirements. Today, we offer you bearings from iglidur materials W300 (standard), J, J4, R, RN248, UW and X. Typical sectors of industry and application areas Plant design Model building Furniture/Industrial design etc. Maintenance-free, self-lubricating Corrosion-resistant High compressive strength When to use it? If you need maintenance-free material When dimensional series E and K components should be fitted If different iglidur materials should be tested If high compressive strength is required If high elasticity is required Improve technology and reduce costs 110 exciting examples online High elasticity When not to use it? If temperatures are higher than +250 C If dimensions above 50 mm are required If rotation speeds higher than 0.5 m/s are required Different materials Drum bearing in a tumble dryer Temperature Depend on material Product Range 6 types Ø 2 50 mm Tolerances The tolerance of the inner diameter is E10. The shaft tolerance should be included between h6 and h9. Carriage in a crane system More information 817

58 balls Product Overview Spherical alls Product Range balls standard balls iglidur W300 (material information page 151) low-cost balls iglidur R (material information page 277) Standard balls: WKM and WKI/WEM and WEI dk dn W...M WKM/WKI Series K metric/inch WEM/WEI metric/inch RKM Series K metric REM metric page 819 page 819 page 820 page 820 high temperatures balls iglidur X (material information page 173) low moisture absorption balls iglidur J (material information page 109) XKM Series K metric XEM metric JKM Series K metric JEM metric page 821 page 821 page page 822 cost-effective balls iglidur J4 (material information page 1266) J4KM Series K metric J4EM metric UWEM metric page 824 page 824 page 825 clearance free balls iglidur J4VEM (material information page 1266) under water applications balls iglidur UW (material information page 565) detectable balls iglidur RN248 (material information page 1269) J4VEM metric RN248KM Series K metric RN248EM metric page 826 page 827 page 827 Part number dn dk Weight E10 WKM WKM WKM WKM WKM WKM WKM WKM WKM WKM WKM WKM WKM WKM Part number dn dk Weight E10 dk dn WEM WEM WEM WEM WEM WEM WEM WEM WEM WEM WEM WEM [g] [g] +90º 40º s [Inch] Width Inner diameter Measuring system M = I = Inch Dimensonal series K = Series K E = Spherical balls made of iglidur W300 Part number dn dk Weight E10 [g] WKI WKI WKI WKI WKI WKI WKI WKI WKI s [Inch] Part number dn dk Weight H10 [g] WEI WEI WEI WEI WEI WEI WEI WEI WEI Life calculation, CAD files and much more support 819

59 balls Spherical alls Product Range Spherical alls Product Range balls Low-cost balls: RKM and REM High temperatures balls: XKM and XEM dk dn R...M dk dn X...M dk dn Width Inner diameter +90º +250º al series K = Series K E = 50º 100º Spherical balls made of iglidur R dk dn 30 Width Inner diameter al series K = Series K E = Spherical balls made of iglidur X Part number dn dk Weight E10 [g] RKM Part number dn dk Weight E10 [g] XKM Part number dn dk Weight E10 [g] REM REM REM REM REM Part number dn dk Weight E10 [g] XEM XEM XEM XEM XEM Life calculation, CAD files and much more support 821

60 balls Spherical alls Product Range New in this catalog! Spherical alls Product Range balls Low moisture absorption balls: JKM and JEM Low moisture absorption balls: JKM dk dn 30 J...M dk dn 30 JKM dk dn º 50º Width Inner diameter al series K = Series K E = Spherical balls made of iglidur J +90º 50º Width Inner diameter al series K Spherical balls made of iglidur J Part number dn dk Weight E10 [g] JKM JKM JKM JKM JKM JKM JKM JKM JKM JKM JKM JKM Part number dn dk Weight E10 [g] JEM JEM JEM JEM JEM JEM JEM JEM JEM JEM JEM JEM Part number dn dk Weight E10 JKM-35-49** New!* JKM JKM-45-60** New!* JKM ** Diameter reduced by means of a plain bearing Low moisture absorption balls, splitted: JKM-GT dk dn 30 JKM-GT-40 Part number dn dk Weight E10 +90º 50º JKM-GT-40 New!* JKM-GT-50 New!* * in this catalog [g] Split ball al series K Spherical balls made of iglidur J [g] Life calculation, CAD files and much more support 823

61 balls Spherical alls Product Range Spherical alls Product Range balls Cost-effective balls: J4KM and J4EM Spherical balls for under water applications: UWEM dk dn dk dn º 50º J4...M Width Inner diameter al series K = Series K E = Spherical balls made of iglidur J4 Part number dn dk Weight E10 [g] J4KM dk dn º 50º UWEM Inner diameter al series E Spherical balls made of iglidur UW Part number dn dk Weight E10 [g] UWEM UWEM UWEM UWEM Part number dn dk Weight E10 [g] J4EM J4EM J4EM J4EM J4EM J4EM J4EM J4EM J4EM J4EM J4EM J4EM Life calculation, CAD files and much more support 825

62 balls Spherical alls Product Range Spherical alls Product Range balls Clearance-free, single piece: J4VEM Spherical balls detectable: RN248KM and RN248EM +90º 50º J4VEM dk dn 30 RN248...M Width Width 0,5 (6x) dk Inner diameter al series E Preloaded Material iglidur J4 dk dn º 50º Inner diameter al series K = Series K E = Spherical balls made of iglidur RN248 Can be combined with all series E housings Sizes 8 to 20 mm Preloaded Totally clearance-free in unloaded state Part number dk Weight E10 [g] J4VEM J4VEM J4VEM J4VEM J4VEM Part number dn dk Weight E10 [g] RN248KM Part number dn dk Weight E10 [g] RN248EM RN248EM RN248EM RN248EM RN248EM Sizes available: Ø 8, 10, 12, 16, 20 mm combinable with: Rod Ends EA(L)RM page 732 Rod Ends E(L)RM page 730 Pillow lock earing ESTM page 771 Flange earing EFOM page 782 Flange earing EFSM page 784 Pivoting earing EGFM-T page 805 Pivoting earing EGLM page 801 Double Joint EGZM page Life calculation, CAD files and much more support 827

63 balls My Sketches detectable detectable Detectable Insensitive to dust and dirt Lubrication- and maintenance-free Vibration-dampening Corrosion-resistant 828 Life calculation, CAD files and much more support 829

64 detectable detectable detectable Product Overview detectable bearings can be found quickly in case of misuse or crash of the system through metal detectable material. Even the smallest fragment can be found by metal detectors. Detectable Insensitive to dust and dirt Lubrication- and maintenance-free When to use it? When particles should be detectable When maintenance-free materials are required If dimensional series K and E should be used If high pressure resistance is required If high elasticity is requested If high pressure resistance is required Integrated lock nut for easy assembly Series K KRM- -CL-DT KLM- -CL-DT For small space requirement ERM- -DT ELM- -DT High strength under impact loads GERM- -DT GELM- -DT Spring-loaded fixing clip GEFM-DT Clevis joints with spring-loaded fixing clip GERMF- -DT GELMF- -DT Spherical alls Series K and E RN248KM RN248EM page 832 page 833 page 834 page 836 page 837 page 827 on request Vibration-dampening When not to use it? If temperatures are higher than +80 C If diameters above 16 mm are required If rotation speeds higher than 0.5 m/s are required Rod Ends Pillow lock earings For higher forces KARM-CL-DT For small space requirement EARM-DT For higher forces KCRM-DT Easy to fit ESTM-DT Extremely light, compact design ESTM-SL-DT page 728 page 732 page 724 page 771 page 775 Flange earings Temperature +80º 30º Product range 4 types Ø 4 16 mm more dimensions on request Easy to install EFOM-DT For higher radial load EFSM-DT page 782 page 784 Pressfit Spherical earings Easy to fit, low-cost For extremely narrow For small space requirement Simply snapping into sheet metal ECLM-DT For tolerance compensation Solid polymer installation space KGLM LC-DT KGLM SL-DT EGLM-DT EGFM-T-DT EGZM-DT page 797 page 798 page 801 page 803 page 805 page More information 831

65 detectable detectable Product Range detectable Product Range detectable Rod ends with female thread: KRM-CL-DT and KLM-CL-DT Rod ends with female thread: ERM-DT and ELM-DT C1 C1 K...M-06-CL-DT E...M-04-DT h1 m h2 h3 d3 W l1 l2 Detectable 2nd Generation Thread L = left-hand thread R = right-hand thread Housing (female thread) al series K l2 h1 d4 d5 d3 W l1 Detectable Thread L = left-hand thread R = right-hand thread Housing (female thread) al series E Smooth design has no dirt traps Smooth design has no dirt traps Compensation for shaft misalignment Housing: RN246 page 1269 Clip in ball Housing: RN246 page 1269 Spherical ball: RN248KM page 827 Compensation for shaft misalignment Spherical ball: RN248EM page 827 Excellent corrosion resistance al series K according to Excellent corrosion resistance standard DIN ISO Part number d3 W C1 h3 h1 h2 l1 l2 m max. Right-hand thread Left-hand thread E10 pivot angle KRM-06-CL-DT KLM-06-CL-DT 6 20 M06 SW Part number d3 d4 d5 C1 h1 l1 l2 W max. E10 pivot angle Right-hand thread Left-hand thread ERM-04-DT ELM-04-DT 4 15 M SW08 33 ERM-05-DT ELM-05-DT 5 19 M SW09 33 ERM-06-DT ELM-06-DT 6 21 M SW11 27 ERM-08-DT ELM-08-DT 8 24 M SW14 24 ERM-10-DT ELM-10-DT M SW17 24 ERM-12-DT ELM-12-DT M SW Life calculation, CAD files and much more support 833

66 detectable detectable Product Range detectable Product Range detectable Clevis joint, detectable: GERM-DT and GELM-DT Clevis joint, detectable: GERM-DT and GELM-DT b1 GE M-04-DT g Detectable I2 Detectable Insensitive to dust and dirt Maintenance-free and lubricant-free Vibration dampening h1 I1 d3 a2 a1 RN246 page 1269 Thread L = left-hand thread R = right-hand thread al series E Clevis joint Part number Max. static tensile strength Max. static radial load Weight Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERM-04-DT GELM-04-DT GERM-05-DT GELM-05-DT GERM-06-DT GELM-06-DT GERM-08-DT GELM-08-DT 1, GERM-10-DT GELM-10-DT 3,290 1, GERM-10-DT-F GELM-10-DT-F 3,290 1, GERM-12-DT GELM-12-DT 3,990 1, GERM-12-DT-F GELM-12-DT-F 3,990 1, Part number g a1 a2 b1 d3 I2 h1 l1 H9 h Thread tolerance Right-hand thread Left-hand thread 6H GERM-04-DT GELM-04-DT M GERM-05-DT GELM-05-DT M GERM-06-DT GELM-06-DT M GERM-08-DT GELM-08-DT M GERM-10-DT GELM-10-DT M GERM-10-DT-F GELM-10-DT-F M10 x GERM-12-DT GELM-12-DT M GERM-12-DT-F GELM-12-DT-F M12 x Life calculation, CAD files and much more support 835

67 detectable detectable Product Range detectable Product Range detectable Spring-loaded fixing clip, detectable: GEFM-DT Clevis joints with spring-loaded fixing clips, detectable: GERMF-DT and GELMF-DT I2 b a GEFM-04-DT GE MF-04-DT detectable detectable C Spring loaded pin h1 l1 Spring loaded pin al series E Thread Clevis joint L = left-hand thread R = right-hand thread Detectable Detectable al series E Insensitive to dust and dirt Insensitive to dust and dirt Clevis joint Maintenance-free and lubricant-free Maintenance-free and lubricant-free Vibration dampening Vibration dampening RN246 page 1269 RN246 page 1269 Part number a b c l1 h1 l2 Weight ±0.5 [g] GEFM-04-DT GEFM-05-DT GEFM-06-DT GEFM-08-DT GEFM-10-DT GEFM-12-DT Part number Max. static tensile strength Max. static radial load Weight Short term Long term Short term Long term Right-hand thread Left-hand thread [N] [N] [N] [N] [g] GERMF-04-DT GELMF-04-DT GERMF-05-DT GELMF-05-DT GERMF-06-DT GELMF-06-DT GERMF-08-DT GELMF-08-DT 1, GERMF-10-DT GELMF-10-DT 2,100 1, GERMF-10-DT-F GELMF-10-DT-F 2,100 1, GERMF-12-DT GELMF-12-DT 2,450 1, GERMF-12-DT-F GELMF-12-DT-F 2,450 1, Individual components: Clevis joint GERM-DT and spring-loaded fixing clip GEFM-DT page 834 and Life calculation, CAD files and much more support 837