MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 & 1

Transcription

1 Parts Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 & 1 MODEL CZT19480KWV CZT19481KWV HZT21480BV HZT21481BV McDonough, GA, U.S.A. Briggs & Startton Yard Power Products Group Copyright 2007 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision 3, 4/26/2007 Manual No

2

3 Table Of Contents PAGE GROUP 4 CASTER WHEEL ASSEMBLY 6 DRIVE TIRE & WHEEL ASSEMBLY 8 FRAME ASSEMBLY 10 FUEL TANK ASSEMBLY, LH 12 FUEL TANK ASSEMBLY, RH (Series 0) 14 FUEL TANK ASSEMBLY, RH (Series 1) 16 SEAT ASSEMBLY (Ferris) 18 SEAT ASSEMBLY (Milsco) 20 MUFFLER GUARD ASSEMBLY 22 TWIN STICK CONTROL ASSEMBLY (R.H.) 24 TWIN STICK CONTROL ASSEMBLY (L.H.) 26 PARKING BRAKE ASSEMBLY 28 LIFT SYSTEM ASSEMBLY 30 ENGINE SUB-ASSEMBLY 32 HYDRO IDLER ASSEMBLY 34 PUMPS, PULLEYS & MOTORS 36 HYDRO RESERVOIR & FILTER ASSEMBLY 38 ROLL BAR PROTECTIVE STRUCTURE 40 48" CUTTING DECK ASSEMBLY (Sub Assy) 42 48" CUTTING DECK ASSEMBLY (Final Assy) 44 48" SPINDLE ASSEMBLY 46 DECALS 48 CONTROL PANEL ASSEMBLY 50 ELECTRICAL COMPONENTS (except wiring) 52 WIRING HARNESS (Briggs Engines) 54 WIRING HARNESS (Kawasaki Engines) 56 WIRING SCHEMATIC (Briggs) 58 WIRING SCHEMATIC (Kawasaki) MID-MOUNT SERIES 0 & 1 3 Manual No

4 CASTER WHEEL ASSEMBLY Manual No MID-MOUNT 4 SERIES 0 & 1

5 CASTER WHEEL ASSEMBLY Item Part No Qty Description Note WELDMENT, Caster (Black textured) used on CZT models WELDMENT, Caster (Red) used on HZT models RING, 1 External Retaining SCREW, 7/16-14 x 6 Hex Head Cap, GR NUT, 7/16-14 Hex Nyloc BUSHING, 1 Machine TUBE, Caster Wheel (5/8 O.D. x 4.510) BALL BEARING, Flanged, 1 I. D. x 2 x 5/8 LUTCO #64F64P ASSY, Front Wheel & Tire (incl. items 9-13) AIR VALVE STEM & CAP, Snap-In BALL BEARING,.625 I.D. x TIRE, 11 x , Smooth Tread RIM, 5.00 Dia. x FITTING, Lube (1/4-28 thread) ALEMITE #3038-B SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap CAP, Caster Shaft (Black) used on CZT models CAP, Caster Shaft (Red) used on HZT models BUSHING, Idler PM Footnotes: MID-MOUNT SERIES 0 & 1 5 Manual No

6 DRIVE TIRE & WHEEL ASSEMBLY Manual No MID-MOUNT 6 SERIES 0 & 1

7 DRIVE TIRE & WHEEL ASSEMBLY Item Part No Qty Description Note WHEEL ASSY, 20 x Ply used on HZT models (incl. items 2A, 3A & 4) WHEEL ASSY, 22 x Ply used on CZT models (incl. items 2B, 3B & 4) 2A TIRE, 20 x Ply 2B TIRE, 22 x Ply Turfmaster 3A RIM, 10 x /4 3B RIM, 10 x VALVE STEM & CAP LUG NUT, 1/2-20 Tapered Seat BRAKE DRUM also shown on Parking Break Assembly page PIN, 9/64 x 1-1/2 Cotter included as part of wheel motor KEY, #11 Woodruff included as part of wheel motor NUT, 3/4-20 Slotted Hex included as part of wheel motor Footnotes: MID-MOUNT SERIES 0 & 1 7 Manual No

8 FRAME ASSEMBLY Manual No MID-MOUNT 8 SERIES 0 & 1

9 FRAME ASSEMBLY Item Part No Qty Description Note WELDMENT, Frame (Black Textured Finish) used on CZT19480KWV WELDMENT, Frame (Black Textured Finish) used on CZT19481KWV WELDMENT, Frame (Red Finish) used on HZT21480BV WELDMENT, Frame (Red Finish) used on HZT21481BV WELDMENT, Pusher Bar SCREW, 3/8-16 x 1-1/4 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc PLATE, Frame Support SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap FAN GUARD SCREW, 5/16-18 x 3/4 Hex Head Cap, GR WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc MAT, Floorpan, CZT MAT, Footrest, CZT FLOORPAN PAD, Floor Pan LUBE FITTING, 3/16 Footnotes: MID-MOUNT SERIES 0 & 1 9 Manual No

10 FUEL TANK ASSEMBLY, LH Manual No MID-MOUNT 10 SERIES 0 & 1

11 FUEL TANK ASSEMBLY, LH Item Part No Qty Description Note SCREW, 7/16-14 x 2 Hex Head Cap, GR WASHER, 1/2 Flat SAE NUT, 7/16-14 Hex Nyloc BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc ASSEMBLY, L.H. Tank CZT (incl. 6 items shown below) 7A FUEL TANK, LH (SNAPPER PRO printed on tank) 7B CAP, Fuel, 3-1/2 Kelch part no C ELBOW, 90-degree Dapco part no D DIP TUBE,.261 I.D. x 24-1/4 7E GROMMET, Dip Tube Dapco part no F 3 SPACER ASSEMBLY, L. H. Tank HZT (incl. 6 items shown below) 8A FUEL TANK, LH (SNAPPER printed on tank) 8B CAP, Fuel, 3-1/2 Kelch part no C ELBOW, 90-degree Dapco part no D DIP TUBE,.261 I.D. x 24-1/4 8E GROMMET, Dip Tube Dapco part no F 3 SPACER BRACKET, Auxiliary Fuel Valve CLAMP, Fuel Hose 11A FUEL HOSE, 1/4 I. D. x 49 (RH) 11B FUEL HOSE, 1/4 I.D. x 17 long 11C FUEL HOSE, 1/4 I.D. x 1' Long ASSEMBLY, 3-Way Fuel Valve BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc WELDMENT, L.H. Tank Bracket CLIP, Harness WELL-NUT, 1/4-20 x 53/ CABLE TIE, 7 not shown Footnotes: MID-MOUNT SERIES 0 & 1 11 Manual No

12 FUEL TANK ASSEMBLY, RH (Series 0) Manual No MID-MOUNT 12 SERIES 0 & 1

13 FUEL TANK ASSEMBLY, RH (Series 0) Item Part No Qty Description Note SCREW, 7/16-14 x 2 Hex Head Cap, GR WASHER, 1/2 Flat SAE NUT, 7/16-14 Hex Nyloc BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc ASSEMBLY, R.H. Tank CZT (incl. 10 items shown below) 7a FUEL TANK, RH (SNAPPER PRO printed on tank) 7b CAP, Fuel, 3-1/2 Kelch part no c ELBOW, 90-degree Dapco part no d DIP TUBE,.261 I.D. x 24-1/4 7e GROMMET, Dip Tube Dapco part no f 3 SPACER 7g SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 7h WASHER, 1/4 Split Lock 7i WASHER, 1/4 Flat 7j LID, Fuel Tank NOTE: Warning text is printed on part ASSEMBLY, R. H. Tank HZT (incl. 10 items shown below) 8a FUEL TANK, RH (SNAPPER printed on tank) 8b CAP, Fuel, 3-1/2 Kelch part no c ELBOW, 90-degree Dapco part no d DIP TUBE,.261 I.D. x 24-1/4 8e GROMMET, Dip Tube Dapco part no f 3 SPACER 8g SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 8h WASHER, 1/4 Split Lock 8i WASHER, 1/4 Flat 8j LID, Fuel Tank NOTE: Warning text is printed on part BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc WELDMENT, R.H. Tank Bracket BRACKET, Auxiliary Fuel Valve WELL-NUT, 1/4-20 x 53/64 Footnotes: MID-MOUNT SERIES 0 & 1 13 Manual No

14 FUEL TANK ASSEMBLY, RH (Series 1) Manual No MID-MOUNT 14 SERIES 0 & 1

15 FUEL TANK ASSEMBLY, RH (Series 1) Item Part No Qty Description Note SCREW, 7/16-14 x 2 Hex Head Cap, GR WASHER, 1/2 Flat SAE NUT, 7/16-14 Hex Nyloc BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc ASSEMBLY, R.H. Tank CZT (incl. 10 items shown below) 7a FUEL TANK, RH (SNAPPER PRO printed on tank) 7b CAP, Fuel, 3-1/2 Kelch part no c ELBOW, 90-degree Dapco part no d DIP TUBE,.261 I.D. x 24-1/4 7e GROMMET, Dip Tube Dapco part no f 3 SPACER 7g SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 7h WASHER, 1/4 Split Lock 7i WASHER, 1/4 Flat 7j LID, Fuel Tank NOTE: Warning text is printed on part in English and Spanish ASSEMBLY, R. H. Tank HZT (incl. 10 items shown below) 8a FUEL TANK, RH (SNAPPER printed on tank) 8b CAP, Fuel, 3-1/2 Kelch part no c ELBOW, 90-degree Dapco part no d DIP TUBE,.261 I.D. x 24-1/4 8e GROMMET, Dip Tube Dapco part no f 3 SPACER 8g SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 8h WASHER, 1/4 Split Lock 8i WASHER, 1/4 Flat 8j LID, Fuel Tank NOTE: Warning text is printed on part BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc WELDMENT, R.H. Tank Bracket BRACKET, Auxiliary Fuel Valve WELL-NUT, 1/4-20 x 53/64 Footnotes: MID-MOUNT SERIES 0 & 1 15 Manual No

16 SEAT ASSEMBLY (Ferris) Manual No MID-MOUNT 16 SERIES 0 & 1

17 SEAT ASSEMBLY (Ferris) Item Part No Qty Description Note * SEAT (Ferris) (Milsco # BB Model XB- 180) used on HZT21480BV SEAT PLATE PIVOT BRACKET, Seat Hinge CROSS PLATE KNOB, Three Prong (5/16-18) WASHER, 5/16 Split Lock SPACER,.33 x.63 x SCREW, 5/16-18 x 1/2 Hex Washer Machine w/nyloc Patch SHOULDER BOLT, 5/ NUT, 5/16-18 Large Flange Hex Center Lock BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SPRING, Compression- Seat Support WASHER, 3/8 SAE Flat ASSEMBLY, Seat Switch (NC) (includes switch p/n 17590) SCREW Footnotes: Note* For Arm Rest components contact Milsco, P.O. Box N. 51st Street Milwaukee, WI ph MID-MOUNT SERIES 0 & 1 17 Manual No

18 SEAT ASSEMBLY (Milsco) Manual No MID-MOUNT 18 SERIES 0 & 1

19 SEAT ASSEMBLY (Milsco) Item Part No Qty Description Note * SEAT (Milsco) w/ Urban Gray Vinyl (Milsco # 06632A) used on CZT19480KWV SEAT PLATE PIVOT BRACKET, Seat Hinge CROSS PLATE KNOB, Three Prong (5/16-18) WASHER, 5/16 Split Lock SPACER,.33 x.63 x SCREW, 5/16-18 x 1/2 Hex Washer Machine w/nyloc Patch SHOULDER BOLT, 5/ NUT, 5/16-18 Large Flange Hex Center Lock BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SPRING, Compression- Seat Support WASHER, 3/8 SAE Flat ASSEMBLY, Seat Switch (NC) (includes switch p/n 17590) SCREW Footnotes: Note* For Arm Rest components contact Milsco, P.O. Box N. 51st Street Milwaukee, WI ph MID-MOUNT SERIES 0 & 1 19 Manual No

20 MUFFLER GUARD ASSEMBLY Manual No MID-MOUNT 20 SERIES 0 & 1

21 MUFFLER GUARD ASSEMBLY Item Part No Qty Description Note BRACKET, Lower Guard Mount BRACKET, Upper Guard Mount REAR SUPPORT, Muffler Guard BACK PLATE, Muffler Guard GUARD, Muffler NUT, 3/8-16 Hex Nyloc BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 21 Manual No

22 TWIN STICK CONTROL ASSEMBLY (R.H.) Manual No MID-MOUNT 22 SERIES 0 & 1

23 TWIN STICK CONTROL ASSEMBLY (R.H.) Item Part No Qty Description Note BEARING, 3/4 I.D. Flange SWITCH, DPDT (NC/NO) WASHER,.77 I.D. Flat RETAINING RING, 3/4 External WALDES # PLATE, Speed Control DAMPENER, Hydraulic C SUPSA COVER, Right Hand TWIN BLOCK BRACKET, Handle Adjustment LEVER GRIP, Twin Stick WELDMENT, Stick Control WELDMENT, Twin Stick 14 1 ASSEMBLY, Pump Control Linkage (Includes item #'s 16, 29 & 30) HANDLEBAR, Twin Stick LINKAGE, Pump Control (5/16-24 threads) per linkage assembly WASHER, 5/16 Flat SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap NUT, 5/16-18 Hex Flange Lock SCREW, 3/8-16 x 2 Hex Head Cap, GR SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR NUT, 5/16-18 Hex Nyloc NUT, 3/8-16 Hex Nyloc SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR NUT, 1/4-20 Hex Nyloc GROOVE PIN, 1/4 x 1-1/4 long BALL JOINT, Pump Control Linkage (5/16-24 thread) per linkage assembly NUT, 5/16-24 Hex, GR 5 per linkage assembly Footnotes: MID-MOUNT SERIES 0 & 1 23 Manual No

24 TWIN STICK CONTROL ASSEMBLY (L.H.) Manual No MID-MOUNT 24 SERIES 0 & 1

25 TWIN STICK CONTROL ASSEMBLY (L.H.) Item Part No Qty Description Note BEARING, 3/4 I.D. Flange SWITCH- DPDT (NC/NO) WASHER,.77 I.D. Flat RETAINING RING, 3/4 External WALDES # PLATE, Speed Control COVER, Left Hand DAMPENER, Hydraulic C SUPSA TWIN BLOCK BRACKET, Handle Adjustment LEVER GRIP, Twin Stick WELDMENT, Stick Control WELDMENT, Twin Stick 14 1 ASSEMBLY, Pump Control Linkage (Includes item #'s 16, 29 & 30) HANDLEBAR, Twin Stick LINKAGE, Pump Control (5/16-24 threads) per linkage assembly WASHER, 5/16 Flat SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap NUT, 5/16-18 Hex Flange Lock SCREW, 3/8-16 x 2 Hex Head Cap, GR SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR NUT, 5/16-18 Hex Nyloc NUT, 3/8-16 Hex Nyloc SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR NUT, 1/4-20 Hex Nyloc GROOVE PIN, 1/4 x 1-1/4 long BALL JOINT, Pump Control Linkage (5/16-24 thread) per linkage assembly NUT, 5/16-24 Hex, GR 5 per linkage assembly Footnotes: MID-MOUNT SERIES 0 & 1 25 Manual No

26 PARKING BRAKE ASSEMBLY Manual No MID-MOUNT 26 SERIES 0 & 1

27 PARKING BRAKE ASSEMBLY Item Part No Qty Description Note WASHER,.77 I.D. Flat BEARING, 3/4 I.D. Flange PIN, 3/8 Self Locking Cotter Was SWIVEL, Brake Link-PM SPACER,.340 I.D. x.63 O.D. x.310 Thick RETAINING RING, 3/4 External Was 29738, WALDES # BRACKET, Brake ROD, Brake Adjustment (3/8-16 thread) BRACKET, Brake Support LINKAGE, Park Brake (3/8-16 thread) WELDMENT, Brake Rod WELDMENT, Brake Hub Rear WELDMENT, Brake Handle BRAKE DRUM ASSEMBLY, Brake Hub SPRING, Brake BRAKE ASSY, (6 inch) WASHER, 3/8 SAE Flat WASHER, 5/16 Split Lock SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was SCREW 5/16-18 x 1 Hex Head Cap, GR 5 Was NUT, 5/16-18 Hex Nyloc NUT, 3/8-16 Hex Nyloc GROOVE PIN, 1/4 x 1-1/4 long HANDLE GRIP (Simplicity) SWITCH- DPDT (NC/NO) SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) Footnotes: MID-MOUNT SERIES 0 & 1 27 Manual No

28 LIFT SYSTEM ASSEMBLY Manual No MID-MOUNT 28 SERIES 0 & 1

29 LIFT SYSTEM ASSEMBLY Item Part No Qty Description Note RING, 3/4 External Retaining WASHER,.77 I.D. Flat PIN, 1/2 x 1-1/8 Clevis LUBE FITTING, 3/ LINK, Lift BRACKET, Deck Support SHIM PLATE PLATE, Height Support TIE ROD, Lift (1/2-13 thread) ASSY, Chain and Eyebolt CHAIN LINKS WELDMENT, Deck Lift Front WELDMENT, Deck Lift Rear WELDMENT, Deck Handle Support SPACER, Lift Adjuster CLIP, 1/2 Roll Pin TETHER STRAP WELDMENT, Lift Arm GRIP (Plastic Cover) SWIVEL, Rod (1/2-13 thread) or SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SCREW, 1/2-13 x 2 Hex Head Cap, GR NUT, 5/16-18 Hex Nyloc NUT, 3/8-16 Hex Nyloc SCREW, 3/8-16 x 2-1/2 Hex Head Cap, GR COTTER PIN, 5/32 x NUT, 1/2-13 Hex Flange Lock, GR WASHER,.531 I.D. Flat NUT, 1/2-13 Hex Center Lock, GR BOLT, 5/16-18 x 1-1/4 Square Neck Carriage, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 29 Manual No

30 ENGINE SUB-ASSEMBLY Manual No MID-MOUNT 30 SERIES 0 & 1

31 ENGINE SUB-ASSEMBLY Item Part No Qty Description Note 1 1 * ENGINE 19 HP Vert Shaft, Kawasaki Elec. Start Mod. FH580V- (shown) AS * ENGINE 19 HP Vert Shaft, Kawasaki Elec. Start Mod. FH580V- KAI BS31R 1 1 * ENGINE 21 HP Briggs & Stratton Mod E1 (not shown) ASSEMBLY, Oil Valve NUT, 5/16-18 Hex Top Lock, GR B CLAMP ASSEMBLY used on Briggs engines only BOLT, 5/16-18 x 1-1/4 Square Neck Carriage, GR NUT, 5/16-18 Hex Flange, GR MUFFLER used on Kawasaki engines only BOLT, 3/8-16 x 1 Square Neck Carriage, GR WASHER, 5/16 Flat SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR KEY, 1/4 Square x 3-1/4 Long PULLEY, Engine, Hydro Drive BRACKET, Clutch RETAINER, 3/8 Bolt NUT, 3/8-16 Hex Nyloc CLUTCH, Electric (Ogura Model # GT2.5-RM01) BUMPER, Electric Clutch WASHER, Rectangular Steel SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR WASHER,.468 x 1.85 x.25 Flat WASHER, 7/16 Split Lock SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 with locking patch FUEL HOSE, 1/4 I. D. x 2-1/ CLAMP, Fuel Line O-RING Kawasaki p/n 670D OIL DRAIN, Short (.375 NPT) MUFFLER used on Briggs engines only SCREW, 5/16-24 x 3/4 Hex Head Cap, GR BRACKET, Muffler (Briggs) WASHER, 5/16 Split Lock NUT, 5/16-24 Hex, GR EXHAUST MANIFOLD, Vanguard HEAT SHIELD, Briggs SCREW, 1/4-20 x 5/8 Hex Head Self-Tap w/free spinning washer Footnotes: NOTE: * Purchase engine components directly from engine manufacturer dealer. MID-MOUNT SERIES 0 & 1 31 Manual No

32 HYDRO IDLER ASSEMBLY Manual No MID-MOUNT 32 SERIES 0 & 1

33 HYDRO IDLER ASSEMBLY Item Part No Qty Description Note BEARING, 9/16 I.D. Flange LUBE FITTING, 3/ FLAT IDLER, 4.12 O.D SPACER,.340 I.D. x.63 O.D. x.310 Thick IDLER STUD (3/8-24) WELDMENT, Idler Arm Hydro Drive SPRING, Extension SWIVEL, Adjustable * BELT, Traction Drive (HA Section, 47.5 Effective Length) Series 0 Moodels * BELT, Traction Drive (4L Section, 48.3 Effective Length) Series 1 Models EYEBOLT, 5/ WASHER, 3/8 Split Lock WASHER, 3/8 SAE Flat NUT, 5/16-18 Hex Nyloc SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR HAIR PIN, 3/32 x 1-1/ NUT, 5/16-18 Hex, GR 5 or B NUT, 3/8-16 Hex Center Lock COTTER PIN, 1/8 x 3/ NUT, 3/8-16 Hex Flange Lock NUT, 3/8-24 Hex, GR B WASHER, 9/16 Flat (Type Narrow) Footnotes: NOTE: * The Snapper part is number stamped on belt. MID-MOUNT SERIES 0 & 1 33 Manual No

34 PUMPS, PULLEYS & MOTORS Manual No MID-MOUNT 34 SERIES 0 & 1

35 PUMPS, PULLEYS & MOTORS Item Part No Qty Description Note PUMP, Hydro-Gear (Left Hand) BDP-10A-454 W/ RTN in Reverse (PG-3KCC-NC1X-XXX) PUMP, Hydro-Gear (Right Hand) BDP-10A-331, W/ RTN in Reverse (PG-34CC-NE1X-XXX) BOLT, 3/8-16 x 1-1/4 Short Neck Carriage, GR RETAINER, 3/8 Bolt WASHER, 3/8 SAE Flat NUT, 3/8-16 Hex Nyloc FAN, 7 Nylon, Counter-Clockwise FITTING, Hydraulic Parker #8 F50X-S FITTING, Hydraulic Parker #8-10 F50X-S HOSE, 19 Hydraulic Parker #F HOSE, 22 Hydraulic Parker #F Pulley, Pump, Hydro Drive (5.00 O.D.) replaces (4.50 O.D.) KEY, M5 x M SET SCREW, 1/4-20 x 1/2 Socket Head w/ Patch Lock WASHER, 1/4 x 1x 1/8 Flat WASHER, 1/4 Split Lock SCREW, M6 1.0 x 12mm Hex Head Cap WHEEL MOTOR, Hydro Gear (HGM-12C-4005) Incl. Castle Nut & Woodruff Key (5/16 x 1 SAE J 502) COTTER PIN, 1/8 x 1-1/ SCREW,1/2-13 x 2-3/4 Hex Head Cap, GR WASHER, 1/2 Split Lock NUT, 1/2-13 Hex GR B KIT, Fan Hub (Includes 1 each of 3 items shown below) (Hydro Gear p/n ) for BDP-10A Pump w/thru Shaft HUB, Fan Mount WASHER, Belleville, Fan Mount NUT, Hex Nyloc Footnotes: MID-MOUNT SERIES 0 & 1 35 Manual No

36 HYDRO RESERVOIR & FILTER ASSEMBLY Manual No MID-MOUNT 36 SERIES 0 & 1

37 HYDRO RESERVOIR & FILTER ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Hadraulic Tank Includes 4 items shown below TANK, Hydraulic, NZM CAP, Vented (Kelch # H4550D) GROMMET (Dapco # 12078) ELBOW FITTING (Dapco # 12784) HOSE CLAMP SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SCREW, 1/4-20 x 1/2 Hex Head Cap, GR WASHER, 1/4 Split Lock BRACKET, Filter NUT, 5/16-18 Hex Flange Lock or ELBOW FITTING, Hydraulic Parker #6 C50X-S FILTER HEAD FILTER UNION TEE Parker # TEE FITTING, Hydraulic Parker #6 S50X-S FITTING, Hydraulic Parker #6 V50X-S SCREW, 1/4-20 x 1 Hex Head Cap, GR 5 or WASHER, 1/4 Flat NUT, 1/4-20 Hex Nyloc BRACKET, Oil Tank HOSE, 17-1/2 Hydraulic Parker R HOSE, 6 long Parker #R801NR39XX * HOSE, 11.5 long Parker #R80137NR06XX * HOSE, 12 Long p/n GRA-12 Footnotes: MID-MOUNT SERIES 0 & 1 37 Manual No

38 ROLL BAR PROTECTIVE STRUCTURE Manual No MID-MOUNT 38 SERIES 0 & 1

39 ROLL BAR PROTECTIVE STRUCTURE Item Part No Qty Description Note WELDMENT, LH Socket WELDMENT, RH Socket WELDMENT POST, LH WELDMENT POST, RH TOP LOOP, Folding, CZT PIN, Hinge (ROPS) SCREW, 1/2-13 x 3-1/4 Hex Head Cap, GR NUT, 1/2-13 Hex Center Lock, GR STAR KNOB (5/16-18 thread) BOLT, 3/8-16 x 1 Square Neck Carriage, GR SEAT BELT, w/metal Strap NUT, 3/8-16 Hex Center Lock RETRACTER, Seat Belt BRACKET, Seat Belt, LH SCREW, 1/2-13 x 1 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc * DECAL, ROPS Overhang * DECAL, Caution ROPS * DECAL, Caution ROPS (Spanish) * DECAL, Warning ROPS * DECAL, Warning ROPS (Spanish) Footnotes: NOTE: CZT Series 1 models equipped with Roll Bar Protective Structure. NOTE: * See Decal Page for pictoral representation. MID-MOUNT SERIES 0 & 1 39 Manual No

40 48" CUTTING DECK ASSEMBLY (Sub Assy) Manual No MID-MOUNT 40 SERIES 0 & 1

41 48" CUTTING DECK ASSEMBLY (Sub Assy) Item Part No Qty Description Note WELDMENT, 48 Deck BOLT, 3/8-16 x 2-3/4 Square Neck Carriage, GR WELDMENT, Pivot Pin NUT, 1/2-13 Hex Light Nyloc NUT, 3/8-16 Hex Nyloc BOLT, 1/2-13 x 5 Hex Head BOLT, 1/2-13 x 3-3/4 Hex Head Cap, GR BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR PULLEY, 6 O.D. Idler p/n AM SPACER, Gage Wheel NUT, 1/2-13 Hex Flange Lock, GR BRACKET, Rear Pusher Bar WELDMENT, Spring Tensioner SCREW, 3/8-16 x 1 Hex Head Cap, GR ASSEMBLY, Pusher Bar SPACER, Pulley BUSHING - Suspension SLEEVE - Suspension WELDMENT, Pusher Bar ROLLER Low Density Polyethylene or WHEEL BRACKET Front Right WHEEL BRACKET Front Left BRACKET, Front Deck Lift, Right Hand BRACKET, Front Deck Lift, Left Hand NUT, 1/2-13 Hex, GR 5 or B WASHER, 1/2 Internal Tooth Lock WASHER, 1/2 Flat WASHER, 3/8 Flat GAGE WHEEL, Polyethylene SCREW, 1/2-13 x 2 Hex Head Cap, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 41 Manual No

42 48" CUTTING DECK ASSEMBLY (Final Assy) Manual No MID-MOUNT 42 SERIES 0 & 1

43 48" CUTTING DECK ASSEMBLY (Final Assy) Item Part No Qty Description Note * BELT, HB Sect nom., HD Deck Belt SWIVEL, 3/8 w/thru hole or SLEEVE BUSHING, 3/4 I. D. GV BOLT, 3/8-16 x 4-1/2 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc PIN, Chute Hinge WASHER,.34 x 1.0 x.09 Flat BOLT, 3/8-16 x 1 Square Neck Carriage, GR * PULLEY, 6 O.D. Idler (assembly) includes pulley ( ) & bushing ( ); replaces BELT GUARD WELDMENT, 48 Discharge Chute WELDMENT, Deck Idler Arm ASSEMBLY, 48 Spindle components are shown on 48 spindle assembly page SPRING, CVT Brake IDLER BOSS ROD, Tensioner (3/8-16 threads) * BELT GUIDE replaces NUT, 3/8-16 Hex, GR 5 or B SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap PIN, 3/32 x 1 Cotter HAIR PIN, 3/32 x 1-1/ * SCREW, 3/8-16 x 2-3/4 Hex Head Cap, GR 5 was WASHER, 3/8 Flat SPRING, Chute ASSY, Discharge Chute used on CZT19481KWV model only WELDMENT, 48 Chute DEFLECTOR, Bottom BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR CHUTE, Rubber 48 Footnotes: NOTE: * The Snapper part is number stamped on belt. NOTE: * , Pulley Replacement Kit includes one each of items 9, 17 & 22. MID-MOUNT SERIES 0 & 1 43 Manual No

44 48" SPINDLE ASSEMBLY Manual No MID-MOUNT 44 SERIES 0 & 1

45 48" SPINDLE ASSEMBLY Item Part No Qty Description Note WASHER for brg. Pre-seal kit WASHER, Beveled LUBE FITTING, 1/4-28 Thread Forming Was 29275, ALEMITE #3038-B GREASE VENT, Spindle ALEMITE # BALL BEARING PULLEY, Driven 48 CZT SHAFT, Spindle WELDMENT, 48 Spindle NUT, 5/8-11 Hex Flange Lock, GR SEAL, Nylos WASHER, Spindle BLADE, 16-1/ RETAINING RING, Internal TRUARC N Footnotes: MID-MOUNT SERIES 0 & 1 45 Manual No

46 DECALS Manual No MID-MOUNT 46 SERIES 0 & 1

47 DECALS Item Part No Qty Description Note DECAL, SNAPPER PRO (2.6 high) used on CZT DECAL, SNAPPER PRO (2.25 high) used on CZT DECAL, SNAPPER (2.75 high) used on HZT DECAL, SNAPPER (2.25 high) used on HZT DECAL, Reservoir Oil Level DECAL, Danger- High Speed Rotating Parts DECAL, Tank Selector, MMZ DECAL, Park Brake, Eng/Span DECAL, Parking Brake similar to (shown above) DECAL, Caution ROPS DECAL, Caution ROPS (Spanish) DECAL, Control Panel, Engl/Span DECAL, Control Panel similar to (shown above) DECAL, Warning (SP) DECAL, Warning, Rollbar DECAL, Chute/Deflector DECAL, ROPS Overhang DECAL, Danger, Cut Finger (CPSC) DECAL, Detent DECAL, Motion Control Levers DECAL, Motion Control Levers (English) similar to (shown above) DECAL, Warning ROPS DECAL, Warning ROPS (Spanish) DECAL, Fuse DECAL, Danger- Guard Catcher DECAL, 48 Deck, Silver DECAL, Belt & Blade Information DECAL, Ear Protection Footnotes: MID-MOUNT SERIES 0 & 1 47 Manual No

48 CONTROL PANEL ASSEMBLY Manual No MID-MOUNT 48 SERIES 0 & 1

49 CONTROL PANEL ASSEMBLY Item Part No Qty Description Note DASH CONSOLE, Black CONTROL LEVER, Throttle/Choke CONTROL CABLE, Throttle (53.99" long) CHOKE CABLE, Briggs, HZT (58.49" long) CONTROL CABLE, Choke (Kawasaki)(53.49" long) SCREW, #10-32 x 5/8 Hex Washer Self-Tap NUT, #10-32 Hex Nyloc SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap TETHER STRAP also shown on Lift System Assembly Page SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was (also shown on Parking Brake Assembly Page) Footnotes: MID-MOUNT SERIES 0 & 1 49 Manual No

50 ELECTRICAL COMPONENTS (except wiring) Manual No MID-MOUNT 50 SERIES 0 & 1

51 ELECTRICAL COMPONENTS (except wiring) Item Part No Qty Description Note SWITCH, Ignition SOLENOID, Super Trombetta (2 Terminal) vendor p/n KEY SET (2), G.C. Ignition not shown SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was ASSEMBLY, Seat Switch (NC) also shown on Seat Assembly pages NUT, 1/4-20 Hex Nyloc SCREW seat switch mount screws SWITCH, PTO, Yellow HOUR METER w/flash Alerts Sendec Corp. Model No BATTERY, 11 Plate 375CCA- Wet SCREW, 1/4-20 x 5/8 Hex Head Cap, GR WASHER, 1/4 Flat NUT, 1/4-20 Hex Center Lock BRACKET, Battery SCREW, #10-32 x 5/8 Hex Washer Self-Tap NUT, #10-32 Hex Nyloc CABLE TIE, 7 not shown CLIP, Harness SWITCH- DPDT (NC/NO) also shown on Twin Stick Control and Parking Brake pages SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) Footnotes: MID-MOUNT SERIES 0 & 1 51 Manual No

52 WIRING HARNESS (Briggs Engines) Manual No MID-MOUNT 52 SERIES 0 & 1

53 WIRING HARNESS (Briggs Engines) Item Part No Qty Description Note WIRE HARNESS, 21 HP Briggs CABLE, Battery- Positive (6 Gage, 34 long) not shown CABLE, Battery- Ground (6 Gage/14 Gage, 23 long) not shown CABLE, Solenoid to Starter (6 Gage, 10 long) not shown WIRE, Solenoid- Ground (10 Gage, 6-1/2 long) not shown Footnotes: MID-MOUNT SERIES 0 & 1 53 Manual No

54 WIRING HARNESS (Kawasaki Engines) Manual No MID-MOUNT 54 SERIES 0 & 1

55 WIRING HARNESS (Kawasaki Engines) Item Part No Qty Description Note WIRE HARNESS, 19 HP Kawasaki CABLE, Battery- Positive (6 Gage, 34 long) not shown CABLE, Battery- Ground (6 Gage/14 Gage, 23 long) not shown CABLE, Solenoid to Starter (6 Gage, 10 long) not shown WIRE, Solenoid- Ground (10 Gage, 6-1/2 long) not shown Footnotes: MID-MOUNT SERIES 0 & 1 55 Manual No

56 WIRING SCHEMATIC (Briggs) Manual No MID-MOUNT 56 SERIES 0 & 1

57 WIRING SCHEMATIC (Briggs) Item Part No Qty Description Note WIRE HARNESS, 21 HP Briggs Footnotes: MID-MOUNT SERIES 0 & 1 57 Manual No

58 WIRING SCHEMATIC (Kawasaki) Manual No MID-MOUNT 58 SERIES 0 & 1

59 WIRING SCHEMATIC (Kawasaki) Item Part No Qty Description Note WIRE HARNESS, 19 HP Kawasaki Footnotes: MID-MOUNT SERIES 0 & 1 59 Manual No

60

61

62 Parts Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 & 1 IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS McDonough, GA, U.S.A. Briggs & Startton Yard Power Products Group Copyright 2007 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision 3, 4/26/2007 Manual No